PROVN OF 2 SHED FOR DG SET,COMPOSTPIT WITH PROTEC BOUNDRY AND COVER FOR GARBAGE DISPOSAL,CERT MISC WKS IN LOGIC SEC,IRON GRILL OVER WINDOW OF DSC ROOM,ATT TOILET AND WASHROOM BLDG P196,IMPROVEMENT TO REST ROOM OF FIRE PKT DUTY PERSON AT AFS MT ABU

Amount

M&L for excavating in post holes or similar work each not exceeding 0.5 CUM in hard dense soil getting out and returning filling and ramming including watering etc and removing surplus to a distance n.exc 50 mtr and making good to ground. In soft / loose soil

M&L for cement concrete type C2 1:3:6 (40 mm graded stone agg) as in posts all as specified and directed.

S&F joist channel angle, tee section, MS pipe, MS square tube ,bars , MS plate fixed in purlin rafter cleat, support etc incl welding, riveting etc conf to Fe-290 Gde E-165 all as directed by Engr-in-charge

M&L preparation of new steel surfaces over 10 cm in width or girth and applying two coat of synthetic enamel paint over one coat of red oxide.

S & F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Surface dressing n.exc 15cm deep in hard /dense soil

M&L for excavating in trenches n.exc 1.5m wide and n.exc 1.5m deep for foundation in any type of soil and getting out etc all as specified and directed by Engg-in-charge.

Removing of excavated material n.exc 50 mtr and depositing where directed at a level n. exc 1.5m above the starting point.

Returning filling in including spreading levelling watering &well ramming in layers n.exc 25 cm in hard/dence soil.

M&L PCC 1:4:8 type D.2 (40mm graded agg) as in fdn filling and mass concrete

M&L for brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius built in CM1:4 all as specifed and directed by Engineer -in- Charge.

M&L RCC M-25 grade in plinth beams, bands; and mass concrete

M&L RCC M-25 grade in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified directed by Engr-in-Charge.

M&L for RCC M-20 grade using 25 mm graded stone aggregate as in slab supported on walls,roof complete all as specified and directed by Engr-in-Charge.

M&L for 10 mm dia and over TMT bar cut to length bent to shape required including cranking bending spirally for hoping for columns hooking ends binding with MS wire n.exc 0.9mm or with securing clips etc.

M&L for 6 to 8 mm dia TMT bar cut to length bent to shape required including cranking bending spirally for hoping for columns hooking ends binding with MS wire n.exc 0.9mm or with securing clips etc.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick,fair finished surface complete all as specified

Formwork to sides and soffits of floor or roof beams, for fair finished surfaces

M&L 15mm thick rendering in cm 1:6 on fair surfaces of walls finished even and smooth w/o using extra cement.

M&L 15mm thick rendering on stone masonry / brick surface in cm 1:4 to finished even and fair.

M&L preparation new plastered surface and applying one coat chalk whiting & two coat of oil bound distemper wash on walls

M&L preparation new plastered surface and applying 3 cots of white wash on Ceilings

Earth filling under floors in layers n exc 25 cm thick spreading & levelling including well ramming complete all as specified and directed.

M&L hardcore of broken stone or boulder n,exc 63 mm deposited spread and leveled in layers n.exc 15 cm thick watered and rammed to a true surface.

M/L 75mm thick Plain cement concrete (1:4:8), type D-2, using 40mm graded crushed stone aggregate as in sub base of flooring complete all as specified and directed by Engr-in-Charge.

M&L 25mm thick PCC 1:2:4 type B-1 with 20mm graded agg as in floor.

M&L screed bed or bedding layer of mortar 20 mm thick with cm 1:6 for laying floor finishes

M&L cement concrete 75 mm thick type C-2 1:3:6 ( 40 mm graded agg ) as in plinth protection etc.

S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; ramed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

M & L for preparation of new steel Surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coat of synthetic enamel paint over a coat of red zinc chrome primer

M&L framed work as in doors or gates of angle or other section with gusset plates, rails, braces,etc., complete drilled for fixing of steel sheeting or other covering , Doors,etc. to be prepared for hanging or sliding with and including either hoks and hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering , running rails and guides) and hanging ; also fastening and fixing complete.

S&F rotational moulded polyethylene water storage tanks (cylinderical, vertical with closed top) of 500 Ltrs capacity hoisted and fixed in position all as specified and directed as per SSR Pt- I

S&F 20mm bore Ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in repair and all as specified and directed by Engr-in-Charge

S&F GI tubes medium grade with all fitting and fixed complete to walls and ceiling or laid in floor in following bore of tube :-

S&F Gun-metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe and fixed in repair and all as specified and directed by Engr-in-Charge

S/F repairs 15 mm bore bib taps chromium plated cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F repair PVC (SWR) pipes single socketed in any length of bore 110mm with rubber ring joints fixed to wall all as specified and directed by Engr-in-charge.

S & F PVC (SWR) bends 110 mm dia

S&F sinks with drainage board made of stainless steel 1 mm thick kitchen with plugs, washers and waste pipes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm X 460 mm bowl size 410 mm x 330 mm x 160 mm

S&F waste fitting/coupling brass chromium plated of 40 mm dia for glazed ware sink, basin, etc with long screwd sanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge Make : GEM/Parko/Soma

M&L for brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius built in CM1:4 all as specifed and directed by Engineer -in- Charge.

M&L 15mm thick rendering in cm 1:6 on fair surfaces of walls finished even and smooth w/o using extra cement.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for keys, scrubbing down with water, etc.

M&L for digital design glazed ceramic tiles in vertical surface of size of each tile 300 x 450 mm and 7 to 8 mm thick fixed to wall with 10 mm thik cement sand mortar in CM 1: 4 , set and joint in neat cement slurry and pointed in white or coloured cement to match the same complete all as specified and directed. (make SOMANY, KAJARIA, MARBITO)

M&L for machine cut kota stone slab flooring 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, moulding on edge and polishing over and including 20mm thick screed bed in CM 1:4 complete all as directed by Engineer-in-Charge.

S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; ramed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

M & L for preparation of new steel Surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coat of synthetic enamel paint over a coat of red zinc chrome primer

Excavating in trenches,n exc 1.5 m wide and n exc 1.5m in depth for foundation etc in any type of soils

M&L for PCC 1:4:8 Type D2 (40 mm graded aggregate)as in foundations,filling and mass concrete

M&L brick work with Sub class B bricks straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6

Returning filling in, including spreading, leveling , watering & well ramming in layer n exc 25 cm

Removing excavated material nexc 50 m and depositing where directed at a level nexc 1.50m above the starting point in soft/loose soil

M&L for reinforced cement concrete of Nominal Mix Type B1 1:2:4 20 mm graded aggregate as in slabs supported on walls

M&L for formwork to soffits of suspended slabs such as roof slabs for flat rough finished surfaces of concrete

M&L for Mild steel TMT bars of 10mm dia and over,cut to length,bent to shape required,including cranking,bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L for rendering 15 mm thick cement plaster on than fair faces of brick work or concrete surfaces in CM 1:4 rendering is to be finished even and smooth without using extra cement adding water proofing compounder 3% by weight of cement (water proofing compound shall be measured and paid separately)

Supply of liquid water proofing compound

M&L for rendering 15 mm thick (1: 6) on fair faces of brick work or concrete surfaces finished even and smooth

M&L for preparing surface and applying three coats of white wash on walls of new surfaces.

M&L for two coats of cement base paint for external faces of walls including preparation

M&L cement concrete 75 mm thick type C-2 1:3:6 ( 40 mm graded agg ) as in plinth protection etc all as directed by Engr in charge .

M&L hard core of gauge nexc 63mm, deposited, spread and levelled inlayers nexc 15cm thick, watered and rammed to a true surface of broken stone or boulder.

M&L cement concrete Type D2 1:4:8 (40 mm graded aggregate) 75 mm thick as in sub base

M & L for Rubber moulded Chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick set , jointed and pointed in neat cement slurry in floors with gray cement and pigment with screed bed 15 mm CM 1:6 complete all as specified by Engr- in- Charge

M/L for Screed bed or bedding layer of cement mortar 15 mm thick for laying floors finishes in cement mortar 1:6 complete all as specified and directed

M&L for non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed

M/L rendering 15 mm thick cement mortar on stone masonary surfaces or surfaces other than fair faces of brick work in cement mortar 1:4 as backing coat to glazed tile complete all as specified and directed

M&L for digital glazed ceramic tiles coloured size 300 x 200 x 7mm thick as on vertical surfaces, of walls as in skirting, dado etc set and jointed in neat cement slurry & pointed with coloured cement to match complete all as specified and directed

S&F Vitreous china squatting pan ,'Orissa' pattern, size 580x440 mm white,with integral foot rests (excluding flushing cistern and flush pipe)

S&F PVC valveless,symphonic action type,flushing cistern ,low level white,with inlet,ball valve,float and handle including brackets of 10 ltrs

S &F Vitreous china bowl urinal flat back ,size of 465x355x265 white (minimum),with grating and union for discharge pipe(excluding flushing cistern,flush pipe and waste pipe)

S&F for waste fittings,brass,chromium plated 40 mm dia for urinals

S&F waste coupling of 40 mm bore(half or full threaded)suitable for urinals

S&F of vitreous china wash basin,white,flat back,size 450x300mm excluding taps,waste,chain and plug and porcelin stopper but including brackets

S&F for waste fittings,brass,chromium plated of 32 mm dia for wash basins

S&F waste coupling of 32 mm bore(half or full threaded)suitable for wash basins

S&F of pillar taps of 15 mm bore chromium plated screwed down high pressure with long screwed shanks and fly nuts

S&F Grating doom 100 mm dia of PTMT (Minimum weight 100 gms)

S/F PVC connections 15mm size with PTMT nuts of length 300mm.

S&F stop valve, 15mm bore dia PTMT of any colour high pressure screwed for iron pipe and fixed (Minimum weight 90 gms) complete all as specified and directed

S&F bib taps, fix cast copper alloy with crutch or butterfly handle, fancy type chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixing 15mm bore dia complete all as specified and directed.

S/F for tubes medium grade, galvanized with iron all fittings fixed to walls, ceiling and laid in floor of sizes complete all as specified and directed :-

15MM Dia

20MM Dia

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube S&F in opening as per specification and drawing

S&F factory made soild panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing.

S&F cold rolled stainless steel butt hinges 75mm size medium weight complete all as specified and directed

S&F aluminium alloy barrel tower bolt 150 mm long

S&F 150 mm aluminium alloy handels cast/plate type

S/F Aluminium alloy, anodised, sliding door bolt 250 mm length with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F towel rail 450mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 170gms)

S & F in 15mm chromium plated swivel shower rose with or without swivel joints sny size for fixing with 15 mm pipe incl shower arm 15 mm

Cutting into existing manholes for connecting new drains, making good to pipe and rendering cutting out existing benching and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required.

S&F reinforced concrete pipe, class NP2 laid and jointed complete with collers 150 mm bore of pipe

Dismantling floor, hearth or wall tiling or stone flooring including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge

M&L for coloured printed non skid tiles area of each tile exceeding exc 0.18 sqm but n.exc 0.38 sqm in floors etc set and jointed with neat cement slurry pointed with colour cement to match the floor, and including 15 mm thick screed bed cement mortar in CM 1:4 and including the chipping of the existing PCC floor complete all as specified.

Demolition of brick work/stone boulder masonary built in cement mortar. including coping but except ashlar facing dressed stone work to precast concrete article complete all as specified and directed

Demolition of Reinforced cement concrete above ground floors exc 15 cms thickness as in roofs,floors,beams and staircases,landings chajjas and similar suspended works(cutting of reinforcement included in the rate)

M/L for Brick works with old size sub class 'B' bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed

M/L for rendering 15 mm thick on fair faces brick work or concrete surfaces in cement 1:4 and finished even and smooth complete all as specified and directed

M&L for plain cement concrete 1:2:4 type B0 (12.5mm graded stone aggregate) as in copings

M&L for preparing surface and applying three coats of white wash on walls of new surfaces.

M&L for preparation of old previously decorated surfaces by brooming down or steel wire brushes, scrapping down smoke soot, moulds, efflorescent salts etc and applying one coat of white wash on walls all as specified.

M/L for preparation of old treated wooden surface of any description not otherwise desceribed over 10 cm width or girth and applying one coat of synthetic enamel paint all as directed.

M&L for machine cut kota stone slab flooring in steps and floor ( 1.2 to 1.5 m length) 20-25mm also in riser thick laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, moulding on edge and polishing over and including 20mm thick screed bed in CM 1:4 and including the chipping of the existing PCC floor complete all as directed by Engineer-in-Charge.

Cutting holes into brick walls built in cement mortar superficial area exc 400 Sq cm but n exc 0.10 Sqm for depth 15 cm

S&F joist channel angle, tee section, MS pipe, MS square tube ,bars , MS plate fixed in purlin rafter cleat, support etc incl welding, riveting etc conf to Fe-290 Gde E-165 all as directed by Engr-in-charge

M&L preparation of new steel surfaces over 10 cm in width or girth and applying two coat of synthetic enamel paint over one coat of red oxide.

S&F pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/clading to wall, molding/folding in circular/semicircular of any position and height fixed with self tapping screws as specified, As directed by Engr-in-charge

M&L 18/19 mm thick block boards interior grade 2 Quality interior grade veneered on both sides,commercial type, fixed with screws to timber frame work

S&F Continuous (piano) hinges 30 mm wide flap, mild steel, bright finish or electrogalvanised

S&F 30mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished

M&L for 2nd class hard wood scantling clean sawn timber fixed for purlins, posts rafters etc, in any position (unframed work) complete all as specified and directed

M&L for beads exc 3mm but n exc 75mm girth on soft wood

M&L for hasp and staple of size 75mm safety type of aluminium anodised incl bolt to hinge plate and fixed with screws

S&F aluminium anodised frame for doors, windows,partitions powder coated (min thickness 50 microns) complete all as specifed and directed

S&F Aluminium anodised powder coated door shutters aluminium section weighing 0.55 kg per mtr incl necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges anodised aluminium snap beading, screws etc complete all as specifed and directed

S&F tinted glass pane 5.5mm thick area of each pane exc 0.5 sqm fixed with beads and metal clips/pins

S&F Aluminium anodised powder coated window shutter, fixed type without sash bar, alumn section section weighing 0.55 kg per mtr incl necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specifed and directed

S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 and fixed with stainless steel wire staples complete.

S&F powder coated aluminium anodized grill of 6/7 mm dia rod square, rectangular, circular or similar type of shape, fixed with channel 38 mm x 12 mm x 1.30 mm (Sec No 8778) all as specified.Make :- DECOREL.

M/S Balkishan Panwar Construction