Addn/Altn to RSSI Bldg No P-06, P-25/2 of HQ 9 Corps at Yol Cantt under AGE B/R-I of GE (KH) YOL

Amount

PART-I:- Dismantling plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, complete all as specified and directed.

Dismantling boarding, any discription fixed in any postion with nails, complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness, laid bedded and pointed in any mortar in floors, aprons etc. including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish of the premisses, complete including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Demolition of stones or brick masonry, built in cement mortar including all quoins, arches etc., but excluding ashlar facing, dressed stone work etc., complete including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Demolition of cement concrete reinforced of any description in any position complete including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 25 or 32mm bore, steel tubing and connections, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking down cement plaster on brick or stone walls, ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.50 Sqm each and removing from site, complete all as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.50 Sqm but not exc. 4 Sqm each and removing from site, complete all as specified and directed.

Dismantling PVC/CI drain pipes, 75 to 110mm dia, fixed to walls, laid in floors or in trenches or in any position including all fittings, complete all as specified and directed.

Dismantling timber scantlings 40 sqcm and over in section, in any position, unframed work, complete all as specified and directed.

Dismantling aluminium windows/partition of any section/description with all fittings and accessories including glass panes, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

Mat finish joint less (non skid), Premium class I grade, coloured/printed, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.18 Sqm but not exc. 0.38 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand), including necessary cutting and waste as per site requirement having 3mm spacers and 10mm depth to be filled by epoxy material pointed in white or coloured cement to match complete all as specified and directed by Engr-In-Charge. Note:- The size, shade and design will be approved by GE.

Vitrified ceramic tiles light shade, 10mm thick glossy/mat finish double charged heavy duty (Square/ rectangular) polished, area of each tile exc. 0.18 Sqm but not exc. 0.38 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand), including necessary cutting and waste as per site requirement having 3mm spacers and 10mm depth to be filled by epoxy material pointed in white or coloured cement to match complete all as specified and directed by Engr-In-Charge. Note:- The size, shade and design will be approved by GE.

Vitrified ceramic tiles light shade, 10mm thick glossy/mat finish double charged heavy duty (Square/ rectangular) polished, area of each tile exc. 0.18 Sqm but not exc. 0.36 Sqm, in skirting, dado etc and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick rendering in cement mortar 1:4 (1 cement : 4 coarse sand), including necessary cutting and waste as per site requirement having 3mm spacers and 10mm depth to be filled by epoxy material or pointed in white or coloured cement to match complete all as specified and directed by Engr-In-Charge. Note:- The size, shade and design will be approved by GE.

Endura tiles/parking tiles 10-12mm thick glossy/mat finish double charged heavy duty (square/rectangular) of approved design, size and shade as directed by Engr-In-Charge in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed by Engr-In-Charge. Note:- The size, shade and design will be approved by GE.

Glazed ceramic, premium quality, coloured/printed tiles of size 350mmx250mm /450mmx350mm /1200mmx600mmx7 to 8mm thick as in skirting, dado etc and the like, set and jointed in neat cement slurry, laid over and including 10mm thick rendering in cement mortar 1:4 (1 cement : 4 coarse sand), including necessary cutting and waste as per site requirement having 3mm spacers and 10mm depth to be filled by epoxy material or pointed in white or coloured cement to match the shade of tile, complete all as specified and directed by Engr-In-Charge. Note:- The size, shade and design will be approved by GE.

Grouting the joints of flooring tiles having joints of 3mm width, using epoxy grout mix of 0.70 Kg of organic coated filler of desired shade (0.10 kg of hardner and 0.20 kg of resin per kg), including filling/grouting and finishing, complete all as specified and directed by Engr-In-Charge.

Black granite 20mm thick (table rubbed and polished) in steps, jambs, pollars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, laid over and including 15mm thick screed bed in cement mortar (1:6), including necessary cutting and waste as per site requirement pointed in white or coloured cement to match, complete all as specified and directed by Engr-In-Charge.

Machine cut kota stone slab flooring 18-20mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:6 (1 cement : 6 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish, complete all as specified and directed.

Plain cement concrete M-7.5, nominal mix, type D-2, using 40mm graded mechanically crushed stone aggregate as in floor for sub base, 75mm thick, complete all as specified and directed.

Taking down existing unserviceable roof treatment materials and PCC/ cement mortar padding etc complete from roof carefully by cutting chiselling, cleaning the surface by scrapping, brooming, brushing etc and removing the rubbish from site, complete all as specified and directed by Engr-in Charge.

Rendering cement plaster 10mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (5mm thick first layers and 5mm thick 2nd layer), mixed with WPC @ 3% by weight of cement on fair faces of brick walls or on concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified and directed. Note:- water proofing compound shall be measured and paid separately.

Providing and applying water profing treatement over terrace using SHALIURETHANE-BTD OF STP MAKE OR EQUIVALENT as approved by GE, high solid content single component water based liquid applied elastomeric water proofing membrene as ASTMC 836 and ASTMD 6083, thickness of the memberane shall be 1.50mm, having solid content of more than 80% elongation of 500+(-) 50% laid over reinforcing layer on non woven geo-textile mesh of 40/50 50gms, including applying self primer coat by diluting with 1:1 ratio @ 0.2 kg per sqm and suface preparation including cleaning of existing treatement, complete all as per specified and directed by Engineer-In-Charge.

Plain cement concrete M-15, nominal mix, type B-0, using 12.50mm graded mechanically crushed stone aggregate as in flooring, 25mm thick, surface finished even and rough for receiving floor finishes, complete all as specified and directed.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5cm deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), complete all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

Plain cement concrete M-15, nominal mix, B-0 using 12.50mm graded mechanically crushed stone aggregate as in lintels upto 1.50 metre clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates for serving hold fasts, filling in mild steel frames etc., kerbs, including weathering slighting rounded or chamfered angles and throating, complete all as specified and directed. Note :- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

Reinforced cement concrete, M-15 (Nominal mix), type B-1, (with 20mm graded crushed stone aggregate as) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings facias, louvres, parapets and railings and similar work; not exceeding 200mm thick (Horizontal or sloping), etc. For fair finished flat surfaces of concrete, complete all as specified and directed.

Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed.

Brick work with old size fly ash bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed.

Walling random rubble masonry with best quality locally available stone, uncoursed, well bonded, bedded, solidly hearted and built in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed.

All as per item No. 39 above but except stone.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) on fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement with WPC @ 3% by weight of cement, complete all as specified and directed. Note:- water proofing compound shall be measured and paid separately.

Supply only integral water proofing compound, complete all as specified and directed.

Rendering plaster 15mm thick in cement mortar 1:6 (1 cement :6 coarse sand) on other than fair faces of brick wall or stone wall surfaces, surface finished even and smooth without using extra cement, complete all as specified and directed.

Rendering cement plaster 10mm thick in cement mortar 1:3 (1 cement : 3 coarse sand) on ceiling, surface finished even and smooth without using extra cement, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of wall to prepare the surface even and smooth and applying finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified and as directed.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over 2mm thick wall with plaster of paries putty, complete all as specified and directed.

Preparation of newly plastered ceiling surfaces and applying one coat of oil bound distemper over 1mm thick wall care paries putty including preparation of surface, complete all as specified and directed.

Preparation of old plastered or unplastered surfaces of wall including complete removal of existing surfaces and applying finishing walls with Acrylic Smooth exterior paint of required shade (Two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified and as directed.

Preparation of old plastered or unplastered surfaces of walls including complete removal of existing treatment and applying two coats of oil bound distemper over 2mm thick wall with plaster of paries putty including cleaning the floor/joinery surfaces, glass pans, complete all as specified and as directed.

Preparation of old plastered or unplastered surfaces of ceilings including complete removal of existing treatment and applying one coat of oil bound distemper over 2mm thick wall with plaster of paries putty, complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick walls, complete all as specified and directed.

Supplying and laying of 16mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors, complete all as specified and directed.

Supplying and laying of 20mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors, complete all as specified and directed.

Supplying and laying of 32mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors, complete all as specified and directed.

25mm Tank Adaptor for CPVC pipes SDR 11 & Plain CPVC SDR 11, complete all as specified and directed by Engr-In-Charge.

20mm Union for CPVC pipes SDR 11 & Plain CPVC SDR 11, complete all as specified and directed by Engr-In-Charge.

16mm Female Brass Threaded Adaptor (FTA/ FBTA) for CPVC pipes SDR 11 & Plain CPVC SDR 11, complete all as specified and directed by Engr-In-Charge.

Sink with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, including 40mm dia waste pipe & CP waste coupling, overall size 915mm x 460mm bowl size 405mm x 355mm x 178mm, fixed in repair, complete all as specified and directed. Make:- Cat Part No SSSB-52 (Silver shine) of Blue Star or equivalent makes mentioned in Appx 'C'.

Angle valve/stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs, complete all as specified and directed. Make: Cat. No.:F360006 of "HINDWARE" or Cat No. F1016201GG of "CERA" or Cat No. 8110 of "PRAYAG" or Cat No. TQT-526N of "ESSCO" or equivalent makes mentioned in Appx 'C' as directed by Engr-in-Charge.

Bib taps, 15mm bore, cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down high pressure, screwed for iron pipe or for brass ferrule fixed in repairs, complete all as specified and directed. Make: Cat. No.: F360004 of "HINDWARE" or F2002152 of "CERA" or Cat No. 8108 of "PRAYAG" or Cat No. TQT-512 of "ESSCO" or equivalent makes mentioned in Appx 'C' as directed by Engr-in-Charge.

Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed, complete all as specified and directed. Make: Cat. No.: F280016/Cat. No.: F280020 of "HINDWARE' or F2002511/ F2002405 of "CERA" or Cat No. 8155/9055 of "PRAYAG" or Cat No. TQT-520/521S of "ESSCO" or equivalent makes mentioned in Appx 'C' as directed by Engr-in-Charge.

Vitreous china wash down water closet (pedestal pattern), with flushing cistern (single piece), coloured of size 800mmx375mmx650mm of Jaquar/ 700mmx370mmx745mm of Prayag/ 650mmx360mmx750mm of Hindware/ 720mmx370mmx760mm of Cera any other size as directed and including S traps, trap distance 180mm connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC coloured seat cover and CP jet/health faucet including PVC connection, fixed complete including demolition of old unserviceable WC and provision of PCC M-15, type B-1, using 20mm graded crushed stone aggregate, complete all as specified and directed. Make:- Cat Part No. ARS-WHT-39751P or ARS-WHT-39201 of jaquar, Cat Part No. ARTISAN 4390 of Prayag, Cat Part No. 20122 (S-22) or 20127 (P-18) of Hindware, Cat Part No. A1014112 of Cera or equivalent makes mentioned in Appx 'C' as directed by Engr-in-Charge. Note:- Size, shape and cat part will be approved by GE.

Brass Chromium Plated, Tubular towel rail, 20mm dia, D type, 60cm long between flanges, with brass brackets, fixed with chromium plated screws, fixed in repair, complete all as specified and directed.

Wash hand basins, vitreous china (table top basin) of size 510x405x185mm oval shape Cat No. ECS-WHT-703 of ESSCO or size 520x310x170mm white colour Cat No. 4719 of Prayag or size 410x340x150mm star white Cat No. 91088 of Hindware or 370x370x115mm snow white canal Cat No. S2020107 of Cera or equivalent makes mentioned in Appx 'C' as directed by Engr-In-Charge, excluding pillar tap etc including silicon or adhesive required to fixed on top of granite shelf with 32mm bore waste fittings, brass, chromium plated with long screwed shanks and fly nuts, PVC connections 15mm size with CP brass coupling nuts of length 450mm, trap, grating and union for discharge pipe, waste, chain and plug and porcelain stopper, chain and plug, bottle trap having minimum water seal of 25mm (minimum weight 32mm-260gms/ 40mm-270gms) or PVC 32mm dia flush pipe and all accessories fixed in repair, complete all as specified and directed.

Pillar cock with long extension body with provision of hot and cold water lever operated having long braided hoses pipe with PVC connection of length 450mm screwed down for iron pipe and fixed complete all as specified and directed. Make: Cat. No.: F520002 of "HINDWARE" or F1016102 of "CERA" or Cat No. 8751 of "PRAYAG" or Cat No. STE107005B of "ESSCO" or equivalent makes mentioned in Appx 'C' as directed by Engr-in-Charge.

Vitreous china urinal, full stall type of approved size white colour with waste coupling of PTMT (half or full threaded) minimum weight 32mm-45gms/40mm-60gms, having urinal spreader for fixing with 15mm dia pipe (Minimum weight 60 gms) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement: fixing automatic flushing cistern with brackets, flush pipe PVC connections 15mm size with CP brass coupling nuts of length 450mm, grating and union for discharge pipe, fixed in repair, complete all as specified and directed.

15mm Push tap button cast copper alloy, chromium plated, fancy type screwed for iron pipe and fixed, suitable for urinals (Minimum weight 15mm-50gms), complete all as specified and directed. Make:- Cat Part No. F8010103 flush valve concealed push type (single flush) 32mm (1.25") of Hindware or equivalent makes mentioned in Appx 'C' as directed by Engr-in-Charge.

Providing and fixing granite stone slab of approved shade table rubbed, edges rounded and polished on both sides of 18mm thick fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6mm nominal size as per direction of Engr-In-Charge and finished smooth, complete all as specified and directed.

S& F in repair PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm dia outlet pipe in cement concrete type B-1 (1:2:4),complete all as specified and directed.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete all as specified and directed.

S&F for 32 mm dia HDPE pipes of pressure rating 6 kgf/cm2 (Waste pipe connect to Sink/WHB for removal of waste), complete all as specified and directed.

S&F for PVC connection 15mm size with PTMT nuts at boths end 600mm long and fixed, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of bore 110mm, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of bore 75mm, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with adjustable clamps of bore 110mm, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with adjustable clamps of bore 75mm, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall or laid in floors of bore 150mm, including taking down old pipe, complete all as specified and directed.

PVC (SWR) junction single, (Single T) equal or unequal, Branch piece 75mm bore, provided with oval access door, fixed in repair, complete all as specified and directed.

PVC (SWR) bends any radius, 110mm bore (fitted with or without access door), fixed in repair, complete all as specified and directed.

PVC (SWR) junction single, (Single T) equal or unequal, Branch piece 110mm bore, fixed in repair, complete all as specified and directed.

PVC (SWR) bends any radius, 75mm bore (fitted with or without access door), fixed in repair, complete all as specified and directed.

PVC (SWR) bends any radius, 150mm bore (fitted with or without access door), fixed in repair, complete all as specified and directed.

PVC (SWR) 110mm vent cowl, complete all as specified and directed.

Rotational moulded polyethylene three layered water storage tank 500 Ltrs capacity (Cylinderical vertical with closed top) 4 layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position including PVC float brass ball valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/PVC storage tank, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge, hips, valley gutters, drip and straight flashing (length and girth as fixed), fixed with self tapping screws, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.60mm thick of any colour having tensile strength of 550 Mpa as in valley gutters, fixed with steel, complete all as specified and directed.

Rolled mild steel joist channel, angle or tee section fixed independantly without connection plate etc. conforming to grade Fe.410-W.Gde-E-250 quality A, steel work, complete all as specified and directed.

Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins angle for shed where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc. conforming to grade Fe.410-W.Gde-E-250 quality A, steel work, complete all as specified and directed.

Applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, complete all as specified and directed.

Opening and refixing of 12mm toughned glass in the same position as in hinged doors, partitions, automatic doors and similar work including cutting to shape, drilling holes required, complete all as specified and directed. Note:- All fittings required to fix in same position are included in this rate.

Removal of glass film or dehatching on 12mm toughened glass using cleansing agent/chemical to prepare the surface for adhesion of live wallpaper well prepared and cleaned complete all as specified and directed by Engr-In-Charge.

Designed plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets or metal frame work and reinforced with GI wire mesh with complete GI metal frame work for seamless ceilling comprising of GI permeter channel 0.55mm thick with two unequal flanges of 20mm and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.90mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each lips of 10.50mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre for flat and curved surface of ceiling, complete all as specified and directed by Engr-In-Charge. Note:- Design and shape will be approved by GE.

Providing and fixing in position wall panelling at all heights with PVC wall panel/sheets (5-9mm thickness) of approved texture, design and patterns, comprising of a frame made in the wall offsets from especially fabricated galvanized mild steel sheet and PVC wall panel/sheets of noncombustible are to be screw fixed with self tapping pan head nickel coated mild steel screws as per direction of Engr-In-Charge. Note:- All fittings including PVC strips like L, U etc fixed at corner edges, adhesives or any other are included in this item.

S & F Powder coated anodized aluminium door chowkhat with shutter of approved design complete with all fixing arrangements including providing and fixing door handles, tower bolts, mortice lock, hinges, door stopper including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- a) Shutter vertical member 85.00 x 44.45 x 1.80mm weighing 1.302 Kg/RM. b) Shutter top member 83.50 x 44.45 x 1.70 mm weighing 1.243 Kg/RM. c) Shutter bottom member 114.30 x 44.45 x 1.29mm weighing 1.139 Kg/RM. d) Shutter lock rail 83.50x44.45x1.70mm weighing 1.243 Kg/RM. e) Anodised aluminium handle, fancy type, 350mm long, Aluminium Door Closer and aluminium tower bolt of size 150mm. (f) 5.50mm thick tinted sheet glass fixed with alumnium beading, silicon lining and gaskets. (g) Aluminium anodised frame of door of section 101.60 x 44.45 x 1.75mm weighing 1.367 Kg/M, with flat iron hold fasts and necessary concrete in PCC M-15, type B-1 using 12.50 mm graded crushed stone aggregate to fix hold fasts all as directed. Note:- Shutter shall be fixed with heavy floor spring or hydraulic door closer ISI marked and pivot, brass lock with duplicate keys.

S&F Powder coated anodized aluminium window/ventilator (double shutter (glazed & Gauged) with chowkhat of approved design complete all as directed with all fixing arrangements (including providing and fixing window handles, tower bolts and provision for fixing lock) including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a) Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881 Kg/RM. (b) Shutter top member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (c) Shutter bottom member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (d) Natural colour 15 micron anodized aluminium anodised frame of chowkhat of section 85.00 x 44.45 x 1.80 mm weighing 1.302 Kg/ RM, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. (e) 5.50mm thick tinted glass fixed with alumnium beading, silicon lining and gaskets complete. (f) The size of anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and anodised aluminium tower bolt of size 100mm (02 Nos). (g) Wiremesh of standard size for approved shutters of sections mentioned above. (Note: All fixtures & fastenings required are included in this rate).

S & F Powder coated anodized aluminium sliding window three track with chowkhat and aluminium grill of approved design complete all as directed with all fixing arrangements (including providing and fixing window handles, tower bolts and provision for fixing lock) including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a) Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881 Kg/RM. (b) Shutter top member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (c) Shutter bottom member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (d) Natural colour 15 micron anodized aluminium anodised frame of chowkhat of section 85.00 x 44.45 x 1.80 mm weighing 1.302 Kg/ RM, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. (e) 5.50mm thick tinted glass fixed with alumnium beading, silicon lining and gaskets and stainless steel wire cloth complete. (f) The size of anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and anodised aluminium tower bolt of size 100mm (02 Nos). (Note: All fixtures & fastenings required are included in this rate).

S&F Powder coated anodized aluminium fixed window/ventilator (glazed & Gauged) with chowkhat of approved design complete all as directed with all fixing arrangements (including providing and fixing window handles, tower bolts and provision for fixing lock) including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a) Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881 Kg/RM. (b) Shutter top member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (c) Shutter bottom member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (d) Natural colour 15 micron anodized aluminium anodised frame of chowkhat of section 85.00 x 44.45 x 1.80 mm weighing 1.302 Kg/ RM, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. (e) 5.50mm thick tinted glass fixed with alumnium beading, silicon lining and gaskets complete. (f) The size of anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and anodised aluminium tower bolt of size 100mm (02 Nos). (g) Wiremesh of standard size for approved shutters of sections mentioned above. (Note: All fixtures & fastenings required are included in this rate).

Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed ballusters walk ways; railings; flat iron for framing grills. framework of water tanks and similar work conforming to Fe.290. Gde-E-165, complete all as specified and directed.

Preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint over a coat of primer, complete all as specified and directed.

2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed, complete all as as specified and directed.

12mm Plywood, grade BWR, type BB, fixed with screws to timber frame work/on walls to receive decorative laminate/mica over it, complete all as as specified and directed.

0.9mm Decorative laminate type-1 of surface finish, colour and pattern as approved mica, fixed with approved adhesive on plywood or board as per manufacturer's instructions, complete all as as specified and directed.

Cupboard cabinet stainless steel hinges suitable for 14-20mm thick wooden panel shutter with 4 hole/2 hole full overlay nickel plated to maximum 105'' opening well fixed, complete all as as specified and directed. Make:- Godrej, Hitachi.

Stainless steel sliding track, 1mm thick, fixed to wooden sliding shutter of cup boards, kitchen racks etc with suitable size cadmium screws, complete all as as specified and directed.

Precast cement M-15 nominal mix, type B-1, using 20mm graded crushed stone aggregate as in landings, cover slab (for manholes etc.), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weatherings, throating etc. and setting in cement mortar 1:6 complete with joints to match, complete all as specified and directed.

Plain cement concrete M-10 nominal mix, type B-1 using 20 mm graded mechanically crushed stone aggregate as in surface channel and drains, complete all as specified and directed.

Taking down point wiring with aluminium/ copper conductor for light point, fan & socket point/ power point etc. complete including switches, sockets, holders, (batten or pendent type), ceiling rose, switch board, bell/buzzer, bell push, and making good to the disturbed surfaces of wall/ floor etc. to match with existing surfaces including white wash/ colour wash/ distempering to match with existing wall/ floor/ ceiling finishes, complete all as specified and directed.

Taking down submain wiring any type and any size and making good disturbed surface by using cement mortar, white cement, putty etc. and match with existing surfaces of walls, floors etc., complete all as specified and as directed.

Taking down sheet metal enclosure DB, MCB, main switch etc and making good distrubed surfaces to match with existing surfaces, complete all as specified and directed.

Point wiring with 1.50 Sqmm copper conductor FRLS (Multi strand) PVC insulated ISI Marked unsheathed cable in and including concealed PVC conduit medium grade, ISI marked of suitable size with all fittings/ accessories and also including PVC insulated ISI marked unsheathed 1.50 Sqmm copper multistranded conductor FLRS as phase, neutral and earth wire connected to common earth dolly and including concealed pressed steel/ cast iron of suitable sizes (modular sunken box) terminal boxes made from 1.60 mm thick sheet for mounting of switches, sockets, fan regulators, light fittings etc. and modular cover plate as top cover for one light point or one fan/exhaust fan point or one bell point, independent, controlled by one way switch/ push button complete all as specified and directed. Note:-i) Wiring colour code i.e Red/Yellow/Blue for phase, Black for neutral and Green for earth shall be maintained. (ii) Insulation test of point wiring.

All as per serial item No '112' above, but for ceiling fan wall fan controlled by one switch 6 Amp, SP, ony way, 240V, complete all as specified and directed.

All as per serial item No '112' above, but for one 3 pin 5 Amps socket outlet on the independent board with 1.50 sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 1.50 sqmm stranded copper conductor cable as continous earth wire, complete all as specified and directed.

All as per serial item No '112' above, but for one 3 pin 5 Amps socket outlet on the same board with 1.50 sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 1.50 sqmm stranded copper conductor cable as continous earth wire, complete all as specified and directed.

All as per serial item No '112' above, but for 3 pin 15 amps socket out let on independent with 2.50 Sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 2.50 Sqmm stranded copper conductor cable as continuous earth wire, complete all as specified and directed.

Supply and fix modular switch piano flush type one way 6 Amps, 1 module, 230V, Fixed, complete all as specified and directed.

Supply and fix modular switch piano flush type one way with indicator 16 Amps, 1 module, 230V, Fixed, complete all as specified and directed.

S&F Modular socket 6 Amp 2/3 Pin combined, two module 230 Volts, complete all as specified and directed.

S&F Modular socket 6/16 Amp 3 Pin combined, two module 230 Volts, complete all as specified and directed.

Ceiling rose 65x50mm, three phase, PVC/Polycarbonate, insulated body and fixed, complete all as specified and directed.

Supply and fixing LED ceiling cove strip light 220V AC surface mounted type with high efficiency PMMA diffuser soft glare free light complete with driver, holder and LED lamp including connecting up with driver three core flexible copper conductor cases of suitable size, complete all as specified and directed. Make:- Wipro, Philips

LED tube light fitting 20W, 6000K, 230V, box type complete bipin holders, connector block and retro LED rod of 20W polycarbonate diffuser having high efficiency (double side connection) complete with all accessories internally prewired batten (double side connection) including connecting up with three core twisted flexible copper conductor cable of suitable size from ceiling rose to connector of light fitting including mounted on PVC square block, complete all as specified and directed. Note:- (i) Contractor shall produce LM 79 & LM 80 test report from OEM owned NABL accredited laboratory. (ii) Contrctor shall give gurantee of complete fitting/fixture for minimum 2 years from the date of completion. (iii) Contractor shall conduct the inspection of company representative at site before installation of fitting/fixture at no extra cost.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 600m sweep with, blades, and frame and louvers, complete all as specified and directed.

Single pole and neutral enclosure with a two pin and earth plug top and socket complete with one single pole MCB 20 Amps, complete all as specified and directed.

MCB SP 6 to 32 Amp, 240 Volts, 10 KA, B series, including taking out old MCB, complete all as specified and directed. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.

MCB SPN 6 to 32 Amp, 240 Volts, 10 KA, B series, including taking out old MCB, complete all as specified and directed. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.

S&F MCCB 4 pole with adjustable type, 160 Amps 415V, 50 Hz, having breaking capacity 36 KA, making all connections using bottle/ pin copper thimbles, complete all as specified and directed.

S&F MCCB 4 pole with adjustable type, 100 Amps 415V, 50 Hz, having breaking capacity 16 KA, making all connections using bottle/ pin copper thimbles, complete all as specified and directed.

Sheet metal enclosures factory made for DBs when MCBs to be used, single pole and neutral (double Door powder coated factory made flush fixed), 12 way, 240 volts with 200 Amp rated bus bar single phase, complete all as specified and directed.

S&F of sheet metal enclosure distribution boards, double door, VTPN, 415 volts, 4 ways, as per IEC 61439-3, degree of protection IP-43 (one incoming three phase and twelve out goings single phase) for MCCB & MCB's comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed comprising of the following:- (a) MCCB 4 pole 100 Amps, AC, 415V, 25 KA=01 No (for incoming). (b) MCB SP 6 to 32 Amps = 12 Nos (for outgoings) complete with 250 Amps fully insulated copper bus bar for each phase and neutral link, prefitted masking sheet fixed flush in wall including chases wall for fixing DB, complete all as specified and directed. Note:- (i) The DB shall be VTPN series of Make:- Schneider or technocommercially equivalent make of L&T/ABB/Legrand. (ii) Connections of the MCCBs/MCBs with cable shall be made through appropriate size pin/bottle type thimble properly crimped. (iii) All the vacant holes of the DB shall be provided with blank plates of appropriate size. (iv) Double continuous earth wire shall be provided for each three phase DB from earthing mains dolly. (v) Cutting chasing shall be part of job at no extra cost. (vi) MCCB and MCB shall be measured and paid seperately

M & L for sub main wiring and including PVC conduit 1.80mm thick, 20mm dia with two single core PVC insulated unsheathed, 1100 Volts grade, (FRLS) copper cable 4 sqmm stranded conductor and one run of PVC insulated unsheathed , 1100 Volts grade, (FRLS) copper cable 4 sqmm (green colour) stranded conductor for earth continuity conductor and connected to common earth dolly with thimble etc. complete all as specified and directed. (Two run of 4 sqmm plus one run 4 sqmm of earth wire will be measured as 1RM). One run of PVC conduit, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit. Note:- (i) Insulation test of point wiring to be carried out on completion of work. (ii) Proper colour coding is to be maintained. (Ph-red, N-black, Earth-green). (iii) Two runs of single core cable with one run of earth cable and suitable size of conduit shall be measured as one RM. (iv) Cutting chases for sub main wiring concealed PVC rigid conduit shall be deemed to be included in the quoted rate of item.

M & L for sub main wiring and including PVC conduit 1.80mm thick, 25mm dia with two single core PVC insulated unsheathed, 1100 Volts grade, (FRLS) copper cable 6 sqmm stranded conductor and one run of PVC insulated unsheathed , 1100 Volts grade, (FRLS) copper cable 6 sqmm (green colour) stranded conductor for earth continuity conductor and connected to common earth dolly with thimble etc. complete all as specified and directed. (Two run of 6 sqmm plus one run 6 sqmm of earth wire will be measured as 1RM). One run of PVC conduit, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit. Note:- (i) Insulation test of point wiring to be carried out on completion of work. (ii) Proper colour coding is to be maintained. (Ph-red, N-black, Earth-green). (iii) Two runs of single core cable with one run of earth cable and suitable size of conduit shall be measured as one RM. (iv) Cutting chases for sub main wiring concealed PVC rigid conduit shall be deemed to be included in the quoted rate of item.

Supply, installation, commissioning and testing bus bar chamber factory made Outdoor type, CPRI approved, size 0.45mx0.75mx0.4m deep, fabricated out of 3.15 mm thick mild steel sheet and vermin proof with neoprene gasket having front opening and locking arrangement mounted angle iron legs made out of angle iron size 40mmx40mmx6mm, 0.40m above ground level and 0.40m embedded in PCC 1:2:4 type B-2 using 40mm graded crushed stone aggregate blocks of size 0.30mx0.30mx0.50m- 04 Nos duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, complete with 200 Amp rated aluminium bus bar size with LED phase indicators (R,Y,B), suitable for 3 phase 4 wire supply system with MCCB 160 Amps 4 pole breaking capacity 36 KA-01 No, duly drilled holes for cable connection mounted on epoxy based post insulator all as required at site, complete all as specified and directed by Engr-In-Charge. Note:- Contractor shall submit the drg of bus bar chamber showing arrangement of MCCB, cable gallery, bus bar chamber overall dimensions and marked all items to be incorporated in to LT panel for approval of accepting officer. Engr-In-Charge shall ensure that LT bus bar shall be made as per approved drg only.

Supply, install, commissioning and testing of commercial Air curtain unit of door opening size 52" x 90" for prevention of dust and conditioned air losses, three phase 440 V, 50 Hz, made out of MS/CRCA sheet of minimum thickness 18 gauge finished with two coats of red oxide primer and final coat of synthetic enamel paint (oven baked) with MS - CRC 18 gauge square perforated suction grills, Aluminium alloy fans and single/three phase electric motor, nozzles etc, complete with fittings and accessories so as to produce 1- 1.5 m/sec air velocity at floor level for door opening, complete all as specified and directed by Engr-In-Charge.

XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 24 Sqmm 4 core laid in trenches passing through pipe or bare in road crossings/ paths/ drains/ floors/ along poles/ ducts/ surface of wall ceiling etc including testing after laying, complete all as specified and directed.

XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 70 Sqmm 3.50 core laid in trenches passing through pipe or bare in road crossings/ paths/ drains/ floors/ along poles/ ducts/ surface of wall ceiling etc including testing after laying, complete all as specified and directed.

Excavation in trenches n exc 1.50 metre wide & n exc 1.50 metre in depth for foundation etc or for shafts, wells, cesspits manholes, pier holes, cables etc n. exc 10 Sqm on plan n exc 1.50 metre in depth and getting out in any type of soil, complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc. 25cm thick each layer of soil, complete all as specified and directed.

Removing excavated material not exc. 50m and depositing where directed at a level not exc. 1.50m above the starting point, complete all as specified and directed.

Sand cushioning for protection of cable using dry river sand, free from particles, complete all as specified and directed by Engr-in-Charge.

Supplying and laying un-reinforced precast concrete cable cover, class LV, type 2, flat size 300mm x 180mm x 40mm, complete all as specified and directed by Engr-in-Charge.

M&L for 50mm dia GI pipe light grade as in trenches, across road or pole, crossings are fixed to wall/pole, complete all as specified and directed. Note:- Excavation and earth work shall be measured and paid seperately.

Cable jointing kit for 11 KV (Earthed) grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 120 sqmm to 150 sqmm, complete all as specified and directed by Engr-in-Charge.

Supply and fix tripple pole and earth enclosure with a three pin and earth plug top and socket complete with one tripple pole MCB 20 Amps, 415V, complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less than 1.50m below ground level, connecting to galvanised iron wire 4mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of GI up to test point and earth wire protected by provision of galvanised iron pipe light grade, 15 mm bore, GI water tubing pipe 20mm bore medium grade with funnel and wire mesh, charcoal and salt, 40mm thick precast RCC (1:2:4) type B-0, Nominal mix, cover reinforced with XPM (weighing not less than 4 Kg/Sqm) with suitable steel handle and angle iron 40x40x3mm frame and chamber of PCC (1:3:6) type C-0 (including earth work in any type of soil, removal of surplus soil to a distance n.exc 50m) and connecting, testing on completion, all as shown on electrical plate No. 03 of SSR-2009 Part-I, complete all as specified and directed by Engr-in-Charge. Note:- (i) Earth lead and protection pipe length upto and including 7.50m is included in quoted rates. (ii) Soil should be free from stones, boulders, aggregates, gravels etc.

Eshaan Construction Co. (BID ID -3138624)