Ambaji UGD, STP and WSS under SJMMSVY(Re invitation) : Ambaji Under Ground Drainage with Sewerage Treatment Plant With Operation and Maintenance With All Allied Works for 02-[Two] Years for UGD work and 07-[Seven] Years for STP Including 03-[Three] Years Defect Liability Period with Operation and Maintenance with All Allied Works for 02-[Two] Years Including 03-[Three] Years Defect Liability Period AND for Ambaji Water Supply Project with Operation and Maintenance with All Allied Works for 02-[Two] Years Including 03-[Three] Years Defect Liability Period Under SJMMSVY

A Total of Schedule-B of Ambaji Under Ground Drainage Under SJMMSVY

Ambaji Water Supply Scheme Under SJMMSVY

Schedule-B15 Pump House at main JOD HW

Schedule-B16 Rising Main From Main JOD HW to all HW

Schedule-B17 Elevated Storage Reservoir at Various Head Works

Schedule-B18 Ground Storage Reservoir at Various Head Works

Schedule-B19 Control Room, Pump house and Chlorination room Various Head Works

Schedule-B20 Electro-Mechanical and Instrumentation Work at Prop. PH

Schedule-B21 Electro-Mechanical and Instrumentation Work at Prop. ESR-1

Schedule-B22 Gravity main Distribution network

Schedule-B23 House Connection for WSS

Schedule-B24 Road Excavation and Restoration-Flexible pavement Road Works

Schedule-B25 Road Excavation and Restoration-Rigid Pavement Road Works

Schedule-B26 Road Excavation and Restoration-Paver Block Road Works

B Total of Schedule-B of Ambaji Water Supply Scheme Under SJMMSVY

Schedule-C1 O&M of Sewerage Scheme except STP for 2 years

Schedule-C2 O&M of STP for 7 years

C Total of Schedule-C of Ambaji Under Ground Drainage Under SJMMSVY

Schedule-C3 O&M of Water Supply Scheme for 2 years

D Total of Schedule-C of Ambaji Water Supply Scheme Under SJMMSVY

[A+C] Total Project cost of Ambaji Under Ground Drainage Under SJMMSVY

[B+D] Total Project cost of Ambaji Water Supply Scheme Under SJMMSVY

[A+B+C+D] Total Project Cost of Ambaji UGD + WSS Under SJMMSVY

Total Project Cost Say in Rs.

Ambaji Under Ground Drainage Under SJMMSVY

Sewerage Network of SPS-01 In Ambaji

Item Description Qty Unit Rate in Rs.

1 Excavation for trenches with shoring & strutting if required as per 4081.95 cu.m. 102.35

required gradient and line including all safety provision using site rails and

stacking excavated stuff including up to all required lead cleaning the site

etc. complete for all lift and strata as specified.

I) In all sort of soils and soft murrum

1.1 II) In hard murrum, boulders incl. macadam road. 1882.00 cu.m. 155.25

1.2 III) In soft rock and/or masonry in CM or L M or Lime Concrete. 1882.00 cu.m. 187.45

1.3 IV) In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking, 2823.00 cu.m. 427.80

chiseling, or by chiseling/breaking only.

I) In all sort of soils and soft murrum

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking, chiseling,

or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking, chiseling,

or by chiseling/breaking only.

2 Providing bedding incl. ramming, watering, levelling, consolidating etc. 4258.00 cu.m. 69.00

complete as per standard and instruction of engineer incharge.

(I) As above with selected excavated earth available near site

2.1 (II) As above with Murrum brought from outside including all lead 2795.00 cu.m. 202.40

3 Providing and casting in situ mass Cement Concrete in 1:4:8 proportion 507.00 cu.m. 3901.95

using granite quartzite trap metal of size 25 mm to 40 mm including

consolidation curing etc. complete.

4 Providing and casting in situ C.C. in grade M-20 (proportions as per mix 26.00 cu.m. 6348.00

design or as per table 9 of IS456 2000 in masses by weigh batching ) using

granite, quartzite trap metal of size 6 mm to 20 mm for RCC work,

including scaffolding centering, formwork, needle vibrated consolidation,

curing complete (excluding cost of reinforcement and neat finishing) with

centering and shuttering/deshuttering etc. complete for Drain Crossing

5 Providing and supplying ISI Standard R.C.C. pipes (Horizontal Cast) of 3520.00 Rmt. 527.00

Sulphate Resisting Cement) in standard lengths of following class and

diameter suitable for either collar joints or rubber ring joints including all

taxes, insurance, transportation, freight charges, octroi, inspection

charges, loading, unloading, conveyance to departmental stores, stacking

Note : One rubber ring should be supplied with each full length socketed

pipe, cost included in rates below.

As Directed by Engineering in charge.

(I) RCC NP3 Pipe

Ambaji Under Ground Drainage Under SJMMSVY

Sewerage Network of SPS-01 In Ambaji

Item Description Qty Unit Rate in Rs.

6 Lowering, laying & jointing R.C.C pipes in C.M. 1:1.5 for following dia in 3520.00 Rmt. 111.55

proper position , grade and alignment as directed by Engineer -in-charge

including conveyance from store to site of work. Labour giving Hydraulic

testing as per ISI code.

R.C.C. PIPES (At any Depth)

7 Providing, fixing and constructing of pre-cast RCC M-40 grade circular 235.00 No 14150.00

manholes with internal dia 1.0m and up to specified depth having pre-cast

RCC M-40 grade circular manhole cover frame (ID 0.56m, OD 0.92m),

conical piece (top ID 0.56m, bottom ID 1.0m, vertical height 0.805m, wall

thickness 125mm), and circular rings of required heights (ID 1.0m, height

150/225/300/600 mm, wall thickness 125mm) below conical piece as per

required depth of manhole and having steel reinforcement in conical piece

@ not less than 80 kg per cum of concrete, including cast-in-situ PCC M-10

grade (1:3:6) foundation of 1.625m dia and 150mm thickness, PCC M15

grade circular wall ID 0.925m, wall thickness 200mm, height equal to ID of

sewer pipe + one wall thickness of pipe + 50 mm (to flush the manhole

frame with road top, height of wall can be increased but not more than

100mm), PCC M15 grade benching and channel portion and up to top

level of sewer pipe etc complete with curing compaction and form work,

supplying and fixing heavy duty SFRC manhole cover as per IS 12592 (Part I

and II), supplying and fixing plastic encapsulated CI/MS foot steps / SFRC

foot steps, including cost of shuttering, steel reinforcement, testing for

water tightness etc. complete in all respect as per drawing, as per

specification and the direction of the Engineer. Note:- Excavation of earth

work and road cutting for manhole will be measured and paid separately.

Pre-cast RCC M-40 grade circular manhole conical piece with inbuilt cover

and frame (height 0.805), cast-in-situ PCC M-10 grade foundation, PCC

M15 grade circular wall ID 0.925m, wall thickness 200mm, wall height

equal to ID of sewer pipe + one wall thickness of pipe + 50 mm, PCC M15

grade benching and channel portion. Depth of manhole shall be measured

from top of manhole cover upto lowest invert of pipe. (Depth includes in

the item = height of Conical piece + ID of Sewer pipe + 1 Wall thickness of

7.1 Providing and fixing pre-cast RCC M-40 grade circular ring of ID 1.0m, wall 190.58 Rmt. 6990.00

thickness 125mm, height 150/225/300/600 mm for constructing extra

depth of manhole beyond depth mentioned in above item as per drawing.

Ambaji Under Ground Drainage Under SJMMSVY

Sewerage Network of SPS-01 In Ambaji

Item Description Qty Unit Rate in Rs.

7.2 Providing, fixing and constructing of pre-cast RCC M-40 grade circular 122.00 No 17800.00

manholes with internal dia 1.2m and up to specified depth having pre-cast

RCC M-40 grade circular manhole cover frame (ID 0.56m, OD 0.92m),

conical piece (top ID 0.56m, bottom ID 1.2m, vertical height 1.005m, wall

thickness 125mm), and circular rings of required heights (ID 1.2m, height

150/225/300/600/900mm, wall thickness 125mm) below conical piece as

per required depth of manhole and having steel reinforcement in Conical

piece @ not less than 80 kg per cum of concrete, including cast-in-situ PCC

M-10 grade (1:3:6) foundation of 1.825m dia and 150mm thickness, PCC

M15 grade circular wall ID 1.125m, wall thickness 200mm, height equal to

ID of sewer pipe + one wall thickness of pipe + 50 mm (to flush the

manhole frame with road top, height of wall can be increased but not

more than 100mm), PCC M15 grade benching and channel portion and up

to top level of sewer pipe etc complete with curing compaction and form

work, supplying and fixing heavy duty SFRC manhole cover as per IS

(Part I and II), supplying and fixing plastic encapsulated CI/MS footsteps /

SFRC footsteps, including cost of shuttering, steel reinforcement, testing

for water tightness etc complete in all respect as per drawing, as per

specification and the direction of the Engineer. Note:- Excavation of earth

work and road cutting for manhole will be measured and paid separately.

Pre-cast RCC M-40 grade circular manhole conical piece with inbuilt cover

and frame (height 1.005), cast-in-situ PCC M-10 grade foundation, PCC

M15 grade circular wall ID 1.125m, wall thickness 200mm, wall height

equal to ID of sewer pipe + one wall thickness of pipe + 50 mm, PCC M15

grade benching and channel portion. Depth of manhole shall be measured

from top of manhole cover upto lowest invert of pipe. (Depth includes in

the item = height of Conical piece + ID of Sewer pipe + 1 Wall thickness of

pipe + increased height of wall (if any) + 50mm)

7.3 Providing and fixing pre-cast RCC M-40 grade circular ring of ID 1.2m, wall 148.39 Rmt. 7810.00

thickness 125mm, height 150/225/300/600/900mm for constructing extra

depth of manhole beyond depth mentioned in above item as per drawing.

8 Refilling the pipeline trenches including ramming, watering, consolidating 3265.00 cu.m. 25.30

disposal of surplus stuff as directed within a radius of 3 Km.

(I) Refilling as Directed

9 Drilling of 900mm dia Horizontal borehole for watermain pipeline 50.00 Rmt. 25712.85

crossing under the road incl in all strata with required length incl fixing

of 800 mm dia M.S casing pipe with pushing etc complete for 450 mm dia

Without Water main & with 800 mm dia. 12 mm plate thickness MS

Ambaji Under Ground Drainage Under SJMMSVY

Sewerage Network of SPS-01 In Ambaji

Item Description Qty Unit Rate in Rs.

10 Providing & erecting C.I & M.S ventilating column 15 cms dia with CI 8.00 No. 47414.50

ornamental cap and min 6 mt height(height may be varying as per site

)base fixed firmly with necessary foundation with one coat of red oxide

paint and one coat of any approved colour with 15 cms dia 10 mt in length

with 0.35*0.35 mt* M 100 encasing,RCC pipe connection with M.H

including excavation and jointing as required etc complete as per drawing

For 12 Mtr. Height (2 m CI and 10m MS)

11 Dewatering by pumping set of required capacity including temporary 9493.00 HP/hr 21.07

platform carting pumping at site and fixing the same in position including

all accessories, and fuel and labour etc. complete.

Pump set of capacity

Ambaji Under Ground Drainage Under SJMMSVY

Sewerage Network of SPS-02 for Ambaji

Item Description Qty Unit Rate in Rs.

1 Excavation for trenches with shoring & strutting if required as per 8055.00 cu.m. 102.35

required gradient and line including all safety provision using site rails and

stacking excavated stuff including up to all required lead cleaning the site

etc. complete for all lift and strata as specified.

I) In all sort of soils and soft murrum

1.1 II) In hard murrum, boulders incl. macadam road. 3806.00 cu.m. 155.25

1.2 III) In soft rock and/or masonry in CM or L M or Lime Concrete. 3806.00 cu.m. 187.45

1.3 IV) In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking, 5709.00 cu.m. 427.80

chiseling, or by chiseling/breaking only.

I) In all sort of soils and soft murrum

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

I) In all sort of soils and soft murrum

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

I) In all sort of soils and soft murrum

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

2 Providing bedding incl. ramming, watering, levelling, consolidating etc. 9689.00 cu.m. 69.00

complete as per standard and instruction of engineer incharge.

(I) As above with selected excavated earth available near site

2.1 (II) As above with Murrum brought from outside including all lead 5214.00 cu.m. 202.40

3 Providing and casting in situ mass Cement Concrete in 1:4:8 proportion 980.00 cu.m. 3901.95

using granite quartzite trap metal of size 25 mm to 40 mm including

consolidation curing etc. complete.

4 Providing and supplying ISI Standard R.C.C. pipes (Horizontal Cast) of 9785.00 Rmt. 527.00

Sulphate Resisting Cement) in standard lengths of following class and

diameter suitable for either collar joints or rubber ring joints including all

taxes, insurance, transportation, freight charges, octroi, inspection

charges, loading, unloading, conveyance to departmental stores, stacking

Note : One rubber ring should be supplied with each full length socketed

pipe, cost included in rates below.

As Directed by Engineering in charge.

(I) RCC NP3 Pipe

Ambaji Under Ground Drainage Under SJMMSVY

Sewerage Network of SPS-02 for Ambaji

Item Description Qty Unit Rate in Rs.

5 Lowering, laying & jointing R.C.C pipes in C.M. 1:1.5 for following dia in 9785.00 Rmt. 111.55

proper position , grade and alignment as directed by Engineer -in-charge

including conveyance from store to site of work. Labour giving Hydraulic

testing as per ISI code.

R.C.C. PIPES (At any Depth)

6 Providing, fixing and constructing of pre-cast RCC M-40 grade circular 636.00 No 14150.00

manholes with internal dia 1.0m and up to specified depth having pre-

cast RCC M-40 grade circular manhole cover frame (ID 0.56m, OD 0.92m),

conical piece (top ID 0.56m, bottom ID 1.0m, vertical height 0.805m, wall

thickness 125mm), and circular rings of required heights (ID 1.0m, height

150/225/300/600 mm, wall thickness 125mm) below conical piece as per

required depth of manhole and having steel reinforcement in conical

piece @ not less than 80 kg per cum of concrete, including cast-in-situ

PCC M-10 grade (1:3:6) foundation of 1.625m dia and 150mm thickness,

PCC M15 grade circular wall ID 0.925m, wall thickness 200mm, height

equal to ID of sewer pipe + one wall thickness of pipe + 50 mm (to flush

the manhole frame with road top, height of wall can be increased but not

more than 100mm), PCC M15 grade benching and channel portion and up

to top level of sewer pipe etc complete with curing compaction and form

work, supplying and fixing heavy duty SFRC manhole cover as per IS

12592 (Part I and II), supplying and fixing plastic encapsulated CI/MS foot

steps / SFRC foot steps, including cost of shuttering, steel reinforcement,

testing for water tightness etc. complete in all respect as per drawing, as

per specification and the direction of the Engineer. Note:- Excavation of

earth work and road cutting for manhole will be measured and paid

Pre-cast RCC M-40 grade circular manhole conical piece with inbuilt cover

and frame (height 0.805), cast-in-situ PCC M-10 grade foundation, PCC

M15 grade circular wall ID 0.925m, wall thickness 200mm, wall height

equal to ID of sewer pipe + one wall thickness of pipe + 50 mm, PCC M15

grade benching and channel portion. Depth of manhole shall be

measured from top of manhole cover upto lowest invert of pipe. (Depth

includes in the item = height of Conical piece + ID of Sewer pipe + 1 Wall

thickness of pipe + 50mm).

6.1 Providing and fixing pre-cast RCC M-40 grade circular ring of ID 1.0m, wall 551.52 Rmt. 6990.00

thickness 125mm, height 150/225/300/600 mm for constructing extra

depth of manhole beyond depth mentioned in above item as per

Ambaji Under Ground Drainage Under SJMMSVY

Sewerage Network of SPS-02 for Ambaji

Item Description Qty Unit Rate in Rs.

6.2 Providing, fixing and constructing of pre-cast RCC M-40 grade circular 78.00 No 17800.00

manholes with internal dia 1.2m and up to specified depth having pre-

cast RCC M-40 grade circular manhole cover frame (ID 0.56m, OD 0.92m),

conical piece (top ID 0.56m, bottom ID 1.2m, vertical height 1.005m, wall

thickness 125mm), and circular rings of required heights (ID 1.2m, height

150/225/300/600/900mm, wall thickness 125mm) below conical piece as

per required depth of manhole and having steel reinforcement in Conical

piece @ not less than 80 kg per cum of concrete, including cast-in-situ

PCC M-10 grade (1:3:6) foundation of 1.825m dia and 150mm thickness,

PCC M15 grade circular wall ID 1.125m, wall thickness 200mm, height

equal to ID of sewer pipe + one wall thickness of pipe + 50 mm (to flush

the manhole frame with road top, height of wall can be increased but not

more than 100mm), PCC M15 grade benching and channel portion and up

to top level of sewer pipe etc complete with curing compaction and form

work, supplying and fixing heavy duty SFRC manhole cover as per IS

12592 (Part I and II), supplying and fixing plastic encapsulated CI/MS

footsteps / SFRC footsteps, including cost of shuttering, steel

reinforcement, testing for water tightness etc complete in all respect as

per drawing, as per specification and the direction of the Engineer. Note:-

Excavation of earth work and road cutting for manhole will be measured

and paid separately.

Pre-cast RCC M-40 grade circular manhole conical piece with inbuilt cover

and frame (height 1.005), cast-in-situ PCC M-10 grade foundation, PCC

M15 grade circular wall ID 1.125m, wall thickness 200mm, wall height

equal to ID of sewer pipe + one wall thickness of pipe + 50 mm, PCC M15

grade benching and channel portion. Depth of manhole shall be

measured from top of manhole cover upto lowest invert of pipe. (Depth

includes in the item = height of Conical piece + ID of Sewer pipe + 1 Wall

thickness of pipe + increased height of wall (if any) + 50mm)

6.3 Providing and fixing pre-cast RCC M-40 grade circular ring of ID 1.2m, wall 120.61 Rmt. 7810.00

thickness 125mm, height 150/225/300/600/900mm for constructing

extra depth of manhole beyond depth mentioned in above item as per

7 Refilling the pipeline trenches including ramming, watering, consolidating 6630.85 cu.m. 25.30

disposal of surplus stuff as directed within a radius of 3 Km.

(I) Refilling as Directed

8 Providing & erecting C.I & M.S ventilating column 15 cms dia with CI 4.00 No. 47414.50

ornamental cap and min 6 mt height(height may be varying as per site

)base fixed firmly with necessary foundation with one coat of red oxide

paint and one coat of any approved colour with 15 cms dia 10 mt in

length with 0.35*0.35 mt* M 100 encasing,RCC pipe connection with M.H

including excavation and jointing as required etc complete as per drawing

For 12 Mtr. Height (2 m CI and 10m MS)

9 Dewatering by pumping set of required capacity including temporary 23731.00 HP/hr 21.07

platform carting pumping at site and fixing the same in position including

all accessories, and fuel and labour etc. complete.

Pump set of capacity

Ambaji Under Ground Drainage Under SJMMSVY

Sewerage Network of SPS-02 for Ambaji

Item Description Qty Unit Rate in Rs.

10 Providing and casting in situ C.C. in grade M-20 (proportions as per mix 310.00 cum 6085.80

design or as per table9 of IS456 2000 in masses by weigh batching )

using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work,

including scaffolding centering, formwork, needle vibrated consolidation,

curing complete (excluding cost of reinforcement and neat finishing)

with centering and shuttering/deshuttering etc. complete for structure

other than water retaining Footing without form work. (For Antifloation

Ambaji Under Ground Drainage Under SJMMSVY

Sewerage Network for TSPS Ambaji

Item Description Qty. Unit Rate in Rs.

1 Excavation for trenches with shoring & strutting if required as per 65292.00 cu.m. 102.35

required gradient and line including all safety provision using site rails and

stacking excavated stuff including up to all required lead cleaning the site

etc. complete for all lift and strata as specified.

I) In all sort of soils and soft murrum

1.1 II)In hard murrum, boulders incl. macadam road. 31372.00 cu.m. 155.25

1.2 III) In soft rock and/or masonry in CM or L M or Lime Concrete. 31372.00 cu.m. 187.45

1.3 IV) In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking, 47059.00 cu.m. 427.80

chiseling, or by chiseling/breaking only.

I) In all sort of soils and soft murrum

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

I) In all sort of soils and soft murrum

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

I) In all sort of soils and soft murrum

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

I) In all sort of soils and soft murrum

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

2.0 Providing bedding incl. ramming, watering, levelling, consolidating etc. 99687.00 cu.m. 69.00

complete as per standard and instruction of engineer incharge.

(I) As above with selected excavated earth available near site

2.1 (II) As above with Murrum brought from outside including all lead 46185.00 cu.m. 202.40

3.0 Providing and casting in situ mass Cement Concrete in 1:4:8 proportion 8199.00 cu.m. 3901.95

using granite quartzite trap metal of size 25 mm to 40 mm including

consolidation curing etc. complete.

Ambaji Under Ground Drainage Under SJMMSVY

Sewerage Network for TSPS Ambaji

Item Description Qty. Unit Rate in Rs.

4.0 Providing and casting in situ C.C. in grade M-20 (proportions as per mix 222.00 cu.m. 6348.00

design or as per table 9 of IS456 2000 in masses by weigh batching )

using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work,

including scaffolding centering, formwork, needle vibrated consolidation,

curing complete (excluding cost of reinforcement and neat finishing) with

centering and shuttering/deshuttering etc. complete for Drain Crossing

5.0 Providing and supplying ISI Standard R.C.C. pipes (Horizontal Cast) of 63860.00 Rmt. 527.00

Sulphate Resisting Cement) in standard lengths of following class and

diameter suitable for either collar joints or rubber ring joints including all

taxes, insurance, transportation, freight charges, octroi, inspection

charges, loading, unloading, conveyance to departmental stores, stacking

Note : One rubber ring should be supplied with each full length socketed

pipe, cost included in rates below.

As Directed by Engineering in charge.

(I) RCC NP3 Pipe

6.0 Lowering, laying & jointing R.C.C pipes in C.M. 1:1.5 for following dia in 63860.00 Rmt. 111.55

proper position , grade and alignment as directed by Engineer -in-charge

including conveyance from store to site of work. Labour giving Hydraulic

testing as per ISI code.

R.C.C. PIPES (At any Depth)

Ambaji Under Ground Drainage Under SJMMSVY

Sewerage Network for TSPS Ambaji

Item Description Qty. Unit Rate in Rs.

7.0 Providing, fixing and constructing of pre-cast RCC M-40 grade circular 4055.00 No 14150.00

manholes with internal dia 1.0m and up to specified depth having pre-

cast RCC M-40 grade circular manhole cover frame (ID 0.56m, OD 0.92m),

conical piece (top ID 0.56m, bottom ID 1.0m, vertical height 0.805m, wall

thickness 125mm), and circular rings of required heights (ID 1.0m, height

150/225/300/600 mm, wall thickness 125mm) below conical piece as per

required depth of manhole and having steel reinforcement in conical

piece @ not less than 80 kg per cum of concrete, including cast-in-situ

PCC M-10 grade (1:3:6) foundation of 1.625m dia and 150mm thickness,

PCC M15 grade circular wall ID 0.925m, wall thickness 200mm, height

equal to ID of sewer pipe + one wall thickness of pipe + 50 mm (to flush

the manhole frame with road top, height of wall can be increased but not

more than 100mm), PCC M15 grade benching and channel portion and up

to top level of sewer pipe etc complete with curing compaction and form

work, supplying and fixing heavy duty SFRC manhole cover as per IS

12592 (Part I and II), supplying and fixing plastic encapsulated CI/MS foot

steps / SFRC foot steps, including cost of shuttering, steel reinforcement,

testing for water tightness etc. complete in all respect as per drawing, as

per specification and the direction of the Engineer. Note:- Excavation of

earth work and road cutting for manhole will be measured and paid

Pre-cast RCC M-40 grade circular manhole conical piece with inbuilt cover

and frame (height 0.805), cast-in-situ PCC M-10 grade foundation, PCC

M15 grade circular wall ID 0.925m, wall thickness 200mm, wall height

equal to ID of sewer pipe + one wall thickness of pipe + 50 mm, PCC M15

grade benching and channel portion. Depth of manhole shall be

measured from top of manhole cover upto lowest invert of pipe. (Depth

includes in the item = height of Conical piece + ID of Sewer pipe + 1 Wall

thickness of pipe + 50mm).

7.1 Providing and fixing pre-cast RCC M-40 grade circular ring of ID 1.0m, wall 3018.23 Rmt. 6990.00

thickness 125mm, height 150/225/300/600 mm for constructing extra

depth of manhole beyond depth mentioned in above item as per drawing.

Ambaji Under Ground Drainage Under SJMMSVY

Sewerage Network for TSPS Ambaji

Item Description Qty. Unit Rate in Rs.

7.2 Providing, fixing and constructing of pre-cast RCC M-40 grade circular 1359.00 No 17800.00

manholes with internal dia 1.2m and up to specified depth having pre-

cast RCC M-40 grade circular manhole cover frame (ID 0.56m, OD 0.92m),

conical piece (top ID 0.56m, bottom ID 1.2m, vertical height 1.005m, wall

thickness 125mm), and circular rings of required heights (ID 1.2m, height

150/225/300/600/900mm, wall thickness 125mm) below conical piece as

per required depth of manhole and having steel reinforcement in Conical

piece @ not less than 80 kg per cum of concrete, including cast-in-situ

PCC M-10 grade (1:3:6) foundation of 1.825m dia and 150mm thickness,

PCC M15 grade circular wall ID 1.125m, wall thickness 200mm, height

equal to ID of sewer pipe + one wall thickness of pipe + 50 mm (to flush

the manhole frame with road top, height of wall can be increased but not

more than 100mm), PCC M15 grade benching and channel portion and up

to top level of sewer pipe etc complete with curing compaction and form

work, supplying and fixing heavy duty SFRC manhole cover as per IS

12592 (Part I and II), supplying and fixing plastic encapsulated CI/MS

footsteps / SFRC footsteps, including cost of shuttering, steel

reinforcement, testing for water tightness etc complete in all respect as

per drawing, as per specification and the direction of the Engineer. Note:-

Excavation of earth work and road cutting for manhole will be measured

and paid separately.

Pre-cast RCC M-40 grade circular manhole conical piece with inbuilt cover

and frame (height 1.005), cast-in-situ PCC M-10 grade foundation, PCC

M15 grade circular wall ID 1.125m, wall thickness 200mm, wall height

equal to ID of sewer pipe + one wall thickness of pipe + 50 mm, PCC M15

grade benching and channel portion. Depth of manhole shall be

measured from top of manhole cover upto lowest invert of pipe. (Depth

includes in the item = height of Conical piece + ID of Sewer pipe + 1 Wall

thickness of pipe + increased height of wall (if any) + 50mm)

7.3 Providing and fixing pre-cast RCC M-40 grade circular ring of ID 1.2m, wall 2418.21 Rmt. 7810.00

thickness 125mm, height 150/225/300/600/900mm for constructing

extra depth of manhole beyond depth mentioned in above item as per

Ambaji Under Ground Drainage Under SJMMSVY

Sewerage Network for TSPS Ambaji

Item Description Qty. Unit Rate in Rs.

7.4 Providing, fixing and constructing of pre-cast RCC M-40 grade circular 51.00 No 23900.00

manholes with internal dia 1.5m and up to specified depth having pre-

cast RCC M-40 grade circular manhole cover frame (ID 0.56m, OD 0.92m),

conical piece (top ID 0.56m, bottom ID 1.5m, vertical height 1.305m, wall

thickness 125mm), and circular rings of required heights (ID 1.5m, height

150/225/300/600/900/1200 mm, wall thickness 125mm) below conical

piece as per required depth of manhole and having steel reinforcement in

conical piece @ not less than 80 kg per cum of concrete, including cast-in-

situ PCC M-10 grade (1:3:6) foundation of 2.125m dia and 150mm

thickness, PCC M15 grade circular wall ID 1.425 m, wall thickness 200mm,

height equal to ID of sewer pipe + one wall thickness of pipe + 50 mm (to

flush the manhole frame with road top, height of wall can be increased

but not more than 100mm), PCC M15 grade benching and channel

portion and up to top level of sewer pipe etc complete with curing

compaction and form work, supplying and fixing heavy duty SFRC

manhole cover as per IS 12592 (Part I and II), supplying and fixing plastic

encapsulated CI/MS footsteps / SFRC footsteps, including cost of

shuttering, steel reinforcement, testing for water tightness etc complete

in all respect as per drawing, as per specification and the direction of the

Engineer. Note:- Excavation of earth work and road cutting for manhole

will be measured and paid separately

Pre-cast RCC M-40 grade circular manhole conical piece with inbuilt cover

and frame (height 1.305), cast-in-situ PCC M-10 grade foundation, PCC

M15 grade circular wall ID 1.425m, wall thickness 200mm, wall height

equal to ID of sewer pipe + one wall thickness of pipe + 50 mm, PCC M15

grade benching and channel portion. Depth of manhole shall be

measured from top of manhole cover upto lowest invert of pipe. (Depth

includes in the item = height of Conical piece + ID of Sewer pipe + 1 Wall

thickness of pipe + increased height of wall (if any) + 50mm)

7.5 Providing and fixing pre-cast RCC M-40 grade circular ring of ID 1.5m, wall 103.45 Rmt. 9220.00

thickness 125mm, height 150/225/300/600/900/ 1200mm for

constructing extra depth of manhole beyond depth mentioned in above

item as per drawing.

8 Refilling the pipeline trenches including ramming, watering, consolidating

disposal of surplus stuff as directed within a radius of 3 Km.

(I) Refilling as Directed

9 Drilling of 600mm dia Horizontal borehole for watermain pipeline 50.00 Rmt. 13345.75

crossing under the road incl in all strata with required length incl fixing

of 500 mm dia M.S casing pipe with pushing etc complete for 300 mm

dia ID watermain.

Without Water main & with 500 mm dia. 8 mm plate thickness MS

Ambaji Under Ground Drainage Under SJMMSVY

Sewerage Network for TSPS Ambaji

Item Description Qty. Unit Rate in Rs.

10 Drilling of 900mm dia Horizontal borehole for watermain pipeline 100.00 Rmt. 25712.85

crossing under the road incl in all strata with required length incl fixing

of 800 mm dia M.S casing pipe with pushing etc complete for 450 mm

dia ID watermain.

Without Water main & with 800 mm dia. 12 mm plate thickness MS

11 Drilling of 1300mm dia Horizontal borehole for watermain pipeline 150.00 Rmt. 47368.50

crossing under the road incl in all strata with required length incl fixing

of 1200 mm dia M.S casing pipe with pushing etc complete for 600 mm

dia ID watermain.

Without Water main & with 1200 mm dia. 16 mm plate thickness MS

12 Providing & erecting C.I & M.S ventilating column 15 cms dia with CI 94.00 No. 47414.50

ornamental cap and min 6 mt height(height may be varying as per site

)base fixed firmly with necessary foundation with one coat of red oxide

paint and one coat of any approved colour with 15 cms dia 10 mt in

length with 0.35*0.35 mt* M 100 encasing,RCC pipe connection with M.H

including excavation and jointing as required etc complete as per drawing

For 12 Mtr. Height (2 m CI and 10m MS)

13 PCC M-15 (Without formwork) 6.00 cu.m. 5441.80

Providing and casting in situ C.C. in grade M-15 (approx. corresp. to prop.

1:2:4) (proportions as per mix design or as per Table 9 of IS456 2000 in

masses by weigh batching ) using granite, quartzite trap metal of size

mm to 20 mm for RCC work, including scaffolding centering, form work,

needle vibrated consolidation, curing comp. up to 6 meter depth or

height (excluding cost of reinforcement and neat

finishing) with centering and shuttering/deshuttering etc. comp. for

structure for other than water retaining.

Providing and cast in situ C.C. in grade M-30 proportions of ingredients as

per mix design by weigh batching using granite, quartzite trap metal of

size 12 mm to 20 mm

and or 6 mm to 12 mm including scaffolding centering formwork, needle

vibrated consolidation, curing and hydraulic testing etc. complete

(excluding cost of

reinforcement) with centering and shuttering/deshuttering etc. comp. up

to 6 meter height /depth Av. G.L.for all water retaining structures.

14.1 RC.C. Top Slab 9.00 cu.m. 9444.95

14.2 RC.C. Base Slab 9.00 cu.m. 9444.95

15 Supplying cutting, bending, binding and placing in position steel as per 13.00 MT 77285.20

plan and design and as per ISS 2502 including cost of steel and binding

wire for reservoirs/structures only including lift up to 6 meter height or

depth below G.L. for all diameters

Do – deformed (TMT) bars confirming to relevant IS Fe – 500 grade for all

Ambaji Under Ground Drainage Under SJMMSVY

Sewerage Network for TSPS Ambaji

Item Description Qty. Unit Rate in Rs.

16 Providing and applying Epoxy paint of approved make to concrete surface 181.00 Sq.m 103.50

for precast chamber including cleaning the surface by scrapping and air

blowers to the satisfaction of Engineer-in-charge necessary scaffolding

etc. complete with all leads and lifts and giving satisfactory hydraulic test

for water tightness as per IS codes

17 RCC Precast MH Frame & Cover 1.0 No. 1121.00

RCC precast M.H. Frame & Cover Manufacture, supply & Delivery at store

or at site of work precast RCC M.200

Frame & cover suitable to drainage M.H. and as per type design &

Drawing including cost of reinforcement M.S.

Angles or Flat, curing mold work etc..

Heavy duty : Frame suitable for 50cm opening of MH

17.1 RCC Precast MH Frame & Cover 1.0 No. 1173.00

RCC precast M.H. Frame & Cover Manufacture, supply & Delivery at store

or at site of work precast RCC M.200

Frame & cover suitable to drainage M.H. and as per type design &

Drawing including cost of reinforcement M.S.

Angles or Flat, curing mold work etc..

Heavy duty : Cover suitable for 50cm opening of MH

18 Providing and fixing PVC steps 90.00 No. 87.00

19 Dewatering by pumping set of required capacity including temporary 47461.00 HP/hr 21.07

platform carting pumping at site and fixing the same in position including

all accessories, and fuel and labour etc. complete.

Pump set of capacity

Ambaji Under Ground Drainage Under SJMMSVY

House Connection for UGD

Item Description Qty Unit Rate in Rs. Amount (Rs.)

1 Excavation for trenches with shoring & strutting as per required gradient 8889.00 Cu.m. 102.35

and line including all safety provision using site rails and stacking

excavated stuff including up to all required lead cleaning the site etc.

complete for all lift and strata as specified. In all sorts of Soil and murrum.

(For Pipeline & Chamber )

For depth upto 1.5 m. In all sort of soils and soft murrum

1.1 In hard murrum, boulders incl. macadam road. 1606.00 cu.m. 155.25

1.2 In soft rock and/or masonry in CM or L M or Lime Concrete. 1606.00 cu.m. 187.45

1.3 In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking, 2409.00 cu.m. 427.80

chiseling, or by chiseling/breaking only.

2 Providing bedding including ramming, watering, levelling consolidating 405.00 Cu.m. 378.35

etc. complete as per standard and instruction of engineer in charge with

required quality sand brought from outside including all lead. (For

3 Providing and supplying in standard length ISI mark rigid unplasticised 10800.00 Rmt. 258.00

PVC pipes suitable for potable water with ring fit joint including cost of

rings, as per IS specification no. 4985/1988 including all local and central

taxes, transportation, freight charges, octroi, inspection charges,

loading, unloading, conveyance to the departmental stores and including

cost of jointing

Test Pressure 8 Kg/cm2.

For 110 mm dia UPVC pipes

3.1 Lowering, laying, fixing and jointing PVC/uPVC/cPVC pipes and specials of 10800.00 Rmt. 21.85

following class and diameter including cost of conveyance from stores to

site of works including cost of labour, material, cement solvent, giving

satisfactory hydraulic testing as per ISI code.

For 110 mm dia UPVC pipes

4 Refilling the pipeline trenches including ramming, watering, consolidating 9105.00 Cu.m. 25.30

disposal of surplus stuff as directed within a radium of 3 Km.

5 Providing and casting in situ C.C. in grade M-15 (approx. corresp. to prop. 1101.00 cu.m. 5641.90

1:2:4) (proportions as per mix design or as per Table 9 of IS456 2000 in

masses by weigh batching ) using granite, quartzite trap metal of size

mm to 20 mm for RCC work, including scaffolding centering, form work,

needle vibrated consolidation, curing comp. up to 6 meter depth or

height (excluding cost of reinforcement and neat finishing) with centering

and shuttering/deshuttering etc. comp. for structure for other than water

6 Providing and cast in situ C.C. in grade M-25 proportions of ingredients as 720.00 cu.m. 9288.55

per mix design by weigh batching using granite, quartzite trap metal of

size 12 mm to 20 mm

and or 6 mm to 12 mm including scaffolding centering formwork, needle

vibrated consolidation, curing and hydraulic testing etc. complete

(excluding cost of

reinforcement) with centering and shuttering/deshuttering etc. comp. up

height /depth Av. G.L.for all water retaining structures

Ambaji Under Ground Drainage Under SJMMSVY

House Connection for UGD

Item Description Qty Unit Rate in Rs. Amount (Rs.)

7 Supplying cutting, bending, binding and placing in position steel as per 57.60 MT 77285.20

plan and design and as per ISS 2502 including cost of steel and binding

wire for reservoirs/structures only including lift up to 6 meter height or

depth below G.L. for all diameters

Do – deformed (TMT) bars confirming to relevant IS Fe – 500 grade for all

8 Cement plaster 20 mm thick in C.M. 1:2 using water proofing compound 7776.00 smt 232.30

of approved quality including finishing etc. complete.

9 Brick work using common burnt clay building bricks having crushing 2268.00 cum 4245.09

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand)(B) Conventional

10 Providing and fixing PVC Step 7200.00 No. 87.00

11 RCC precast M.H. Frame & Cover Manufacture, supply & Delivery at store 3600.00 No. 813.00

or at site of work precast RCC M.200 Frame & cover suitable to drainage

M.H. and as per type design & Drawing including cost of reinforcement

M.S. Angles or Flat, curing mold work etc.

House Connection Chamber light duty Frame

Ambaji Under Ground Drainage Under SJMMSVY

Demolition and construction of Road Works

Item Description Qty. Unit Rate in Rs.

1 DEMOLITION AND CONSTRUCTION OF FLEXIBLE PAVEMENT ROAD 4460.00 Cum 22.96

WORKS (ASPHALT)

Rolling of earthwork in layers with power roller including filling in

depressions which occur during the process.

Watering of earth work as directed.

1.1 Construction of granular sub-base (Grade - III) by providing coarse graded 4460.00 Cum 1008.25

material, spreading in uniform layers with motor grader on prepared

surface, mixing by mix in place method with rotavator at OMC, and

compacting with vibratory roller to achieve the desired density, complete

as per MoRTH clause

1.2 Providing, laying, spreading and compacting graded stone aggregate to 5580.00 Cum 1039.91

wet mix macadam specification including premixing the Material with

water at OMC in mechanical mix plant carriage of mixed Material by tipper

to site, laying in uniform layers with paver in sub- base / base course on

well prepared surface and compacting with vibratory roller to achieve the

desired density as per MoRTH Clause

1.3 Providing and applying Prime coat with Slow Setting Bitumen Emulsion 22290.00 Sqm 62.38

binder (SS- 1) @ rate of 7.5 Kg./10 sq.m. of road surface using Emulsion

pressure sprayer etc.,cleaning the road surface complete including cost of

material labour etc complete as directed by engineer in charge.

1.4 Providing and laying Dense Graded Bituminous Macadam in two layer 5350.00 MT 3259.67

(single layer not more than 75 mm) using BT stone chips as per MoRTH

gradation and specification with Bitumen Grade (VG 30) for mixing @

45.00 Kg /MT of total Wt. of mix i.e (4.50 % of total weight mix) including

tack coat @ 2.5 kg/10 smt with Bitumen Emulsion (Rapid setting) and

mixing aggregate & asphalt by batch mix plant and spreading the

mechanical means including rolling & consolidation with 10-12 tonne

vibratory roller & providing all materials equipment's tools & plants, fire

wood, oil , kerossene,labour charges , using contractor 's own machinery

etc Complete as directed by engineer in charge as per MoRTH

1.5 Providing and laying Bituminous concrete using BT aggregate as per 2220.00 MT 3577.19

MORTH gradation ,specification and asphalt Grade VG 30 mixing @54.00

Kg /MT of total Wt. of mix i.e. (5.40% of total weight mix) including

heating and mixing aggregate & asphalt by batch mix plant spreading the

mechanical means including rolling & consolidation with 10-12 tonne

vibratory roller,Tandem Roller & providing all materials equipment's tools

& plants, fire wood, oil , kerossene,labour charges , using contractor 's

own machinery etc Complete as directed by engineer in charge as per

MoRTH Specification

1.6 Excavation in bituminious road as per required gradient and line including 3343.00 Cum 288.65

safety provisions using site rails and stacking excavated stuff including up

to all required lead cleaning the site etc. complete for all lifts as specified.

Ambaji Under Ground Drainage Under SJMMSVY

Demolition and construction of Road Works

Item Description Qty. Unit Rate in Rs.

2 DEMOLITION AND CONSTRUCTION OF RIGID PAVEMENT ROAD WORKS 8130.00 Cum 22.96

Rolling of earthwork in layers with power roller including filling in

depressions which occur during the process.

Watering of earth work as directed.

2.1 Construction of dry lean cement concrete Sub- base over a prepared sub- 4470.00 Cum 2058.78

grade with coarse and fine aggregate conforming to IS: 383, the size of

coarse aggregate not exceeding 25 mm, aggregate cement ratio not to

exceed 15:1, aggregate gradation after blending to be as per table 600-1,

cement content not to be less than 150 kg/ cum, optimum moisture

content to be maintain during construction, concrete strength not to be

less than 10 Mpa at 7 days, mixed in a batching plant, transported to site,

laid with a paver compacting with 8-10 tonnes vibratory roller, finishing

and curing as per MoRTH clause

2.2 Construction of un-reinforced, dowel jointed, plain cement concrete 8940.00 Cum 6972.71

pavement over a prepared sub base with in M -40 grade of concrete with

43 grade cement , coarse and fine aggregate conforming to IS

maximum size of coarse aggregate not exceeding 25 mm, mixed in a

batching and mixing plant as per approved mix design, transported to site

and mechanically laid, compacted and finished in a continuous operation

including provision of contraction, expansion, construction and

longitudinal joints, joint filler, separation membrane, sealant primer, joint

sealant, debonding strip, dowel bar, tie rod, admixtures as approved,

curing compound, finishing to lines and grades as per drawing as per

2.3 Excavation of C.C. Road of any thickness etc. complete with stacking the 12182.00 Cum 427.80

material as directed by the Engineer-in-charge.

3 DEMOLITION AND CONSTRUCITON OF PAVER BLOCK ROAD WORKS 460.00 Cum 22.96

Rolling of earthwork in layers with power roller including filling in

depressions which occur during the process. Watering of earth work as

3.1 Providing, laying, spreading and compacting graded stone aggregate to 580.00 Cum 1039.91

wet mix macadam specification including premixing the Material with

water at OMC in mechanical mix plant carriage of mixed Material by tipper

to site, laying in uniform layers with paver in sub- base / base course on

well prepared surface and compacting with vibratory roller to achieve the

desired density as per MoRTH Clause

3.2 Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete 2290.00 Sqm 701.90

block 60mm thick with grade of concrete M300 pnumatic compressed /

vibrated mechanically and as per approved design Confirming to IS 15658 :

2006 including 35 mm Sand layer for levelling and filling the joint with

sand in proper line and level as per guidlines of IRC : SP 63 (Latest

Revision) etc. Complete.

Ambaji Under Ground Drainage Under SJMMSVY

Demolition and construction of Road Works

Item Description Qty. Unit Rate in Rs.

3.3 Dismentaling tiled of stone floors laid in mortar including stacking of 2283.30 Sqm 49.12

serviceable materilas and disposal of unserviceable materials with all lead

Ambaji Under Ground Drainage Under SJMMSVY

Civil Work of Construction of Sewage Pumping Station (SPS-01)

Item Description Qty. Unit Rate in Rs.

1 Excavation for foundation with shoring & strutting if required as per 84.00 cu.m. 102.35

required gradient and line including all safety provision using site rails and

stacking excavated stuff including up to all required lead cleaning the site

etc. complete for all lift and strata as specified.

I) In all sort of soils and soft murrum

1.1 II) In hard murrum, boulders incl. macadam road. 56.00 cu.m. 155.25

1.2 III) In soft rock and/or masonry in CM or L M or Lime Concrete. 56.00 cu.m. 187.45

1.3 IV) In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking, 84.00 cu.m. 427.80

chiseling, or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

2 Refilling the pipeline trenches incl. ramming, watering, consolidating 140.00 cu.m. 25.30

desposal of surplus stuff as directed within a radius of 3 km.

Refilling as directed

3 Refilling the pipeline trenches incl. ramming, watering, consolidating 360.00 cu.m. 201.25

desposal of surplus stuff as directed within a radius of 3 km.

--do-- with selected soil brought from outside including all

4 Anchor bars below RCC raft slab including drilling of necessary size hole in 229.00 No. 1893.00

dry or wet condition, grouting with hilti OR EQUILVANT in dry or wet

condition, including random pull out test for 5% of total bars anchored as

per drawing and instruction of engineer-in-charge, (excluding cost of TMT

Bars) (In Hard Rocky Strata)

5 Providing and casting in situ C.C. in grade M-15 (approx. corresp. to prop. 20.00 cu.m. 5641.90

1:2:4) (proportions as per mix design or as per Table 9 of IS456 2000 in

masses by weigh batching ) using granite, quartzite trap metal of size

mm to 20 mm for RCC work, including scaffolding centering, form work,

needle vibrated consolidation, curing comp. up to 6 meter depth or

height (excluding cost of reinforcement and neat finishing) with centering

and shuttering/deshuttering etc. comp. for structure for other than water

retaining. Footing (With form work)

Ambaji Under Ground Drainage Under SJMMSVY

Civil Work of Construction of Sewage Pumping Station (SPS-01)

Item Description Qty. Unit Rate in Rs.

6 Providing and casting in situ C.C. in grade M-15 (approx. corresp. to prop. 10.00 cu.m. 5441.80

1:2:4) (proportions as per mix design or as per Table 9 of IS456 2000 in

masses by weigh batching ) using granite, quartzite trap metal of size

mm to 20 mm for RCC work, including scaffolding centering, form work,

needle vibrated consolidation, curing comp. up to 6 meter depth or

height (excluding cost of reinforcement and neat finishing) with centering

and shuttering/deshuttering etc. comp. for structure for other than water

retaining. Footing (Without form work)

7 Providing and cast in situ C.C. in grade M-30 proportions of ingredients as 30.00 cu.m. 9444.95

per mix design by weigh batching using granite, quartzite trap metal of

size 12 mm to 20 mm and or 6 mm to 12 mm including scaffolding

centering formwork, needle vibrated consolidation, curing and hydraulic

testing etc. complete (excluding cost of reinforcement) with centering

and shuttering/deshuttering etc. camp. up to 6 meter height /depth Av.

G.L.for all water retaining structures.

R.C.C. base slab

7.1 R.C.C. walls 60.00 cu.m. 9295.45

7.2 R.C.C. staircase 2.00 cu.m. 9654.25

7.3 R.C.C Beams 4.00 cu.m. 9758.90

7.4 RCC Column 3.00 cu.m. 10714.55

7.5 R.C.C. Top slab 3.00 cu.m. 9444.95

8 Supplying cutting, bending, binding and placing in position steel as per 14.00 MT 77285.20

plan and design and as per ISS 2502 including cost of steel and binding

wire for reservoirs/structures only including lift up to 6 meter height or

depth below G.L. for all diameters. Do-deformed (TMT) bars confirming

to relevant IS Fe-500 grade for all diameters.

9 Grouting with 1:3 cement mortar for anchor bolt pockets machine bases, 2.00 cu.m. 3566.95

pipe sleeves, pocket holes etc. including roughening and cleaning of

concrete surfaces curing etc. complete.

10 Providing 20 mm thick Cement plaster in Cement mortar (1:2) using 100.00 smt 232.30

water proofing compound of approved quality including finising etc .

11 Providing and applying 20 mm thick sand faced cement plaster at outside 40.00 smt 320.70

RCC / brick on work upto height 10 mtr. above ground level consisting of

12 mm thick backing coat of C. M. 1:3 (1 cement : 3 sand) and 8 mm thick

finishing coat of C. M. 1:1 (1 cement : 1 sand) etc. complete.

12 'Providing and applying 15 mm thick cement plaster in single coat on brick 10.00 smt 234.35

work with floating coat of net cement slurry for interior plastering of

pumphouse and outside plastering of sump upto finished even and

smooth in Cement motar 1 : 3 (1 cement : 3 sand) including racking out

joint curing, scaffolding required if any, with necessary cement finishing

etc. complete as directed.

Ambaji Under Ground Drainage Under SJMMSVY

Civil Work of Construction of Sewage Pumping Station (SPS-01)

Item Description Qty. Unit Rate in Rs.

13 Providing and laying 40 mm thick heavy duty cement concrete flooring in 20.00 smt 382.11

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) with water proofing compound and ironite powder

including finishing with a floating of neat cement etc. complete laid in one

layer in wet well area below GL, and for platform of pumphouse 40 mm

14 Providing and laying polished Kota stone slab flooring over 20 mm 5.00 smt 1067.32

(average) thick base of cement mortar 1:6 (1 cement : 6 coarse sand) laid

over and jointed with grey cement slurry including rubbing and polishing

etc. complete at office area, etc. 30 mm thick

15 Providing and applying epoxy paint of approved make to concrete surface 113.00 smt 103.50

for RCC structure including cleaning the surface by scrapping and air

blowers to the satisfaction of Engineer-in -charge necessary scaffolding

etc. complete with all leads and lifts and giving satisfactory hydraulic test

for water tightness as per IS codes. For new surface-Two coats

16 Wall painting (two coats) with plastic emulsion paint of approved brand 40.00 smt 83.18

and manufacture of undercoated wall surface to give an even shade

including thoroughly brushing the surface free from mortar dropings and

other foreign matter and sand papered smooth.

17 Providing & fixing 50 cm wide MS ladder (without safety cage) fabricated 6.00 Rmt. 3392.50

from MS flats 10 mm x 75 mm with 20 mm dia steel bar steps in double

rows @ 30 cm C/C. The include stays of 10 mm x 50 mm flats fixed at

mt. C/C with welding anchoring and 3 coats anticorrsive paint.

18 Providing Cement vata (10 cm x 10 cm size) quarter round in cement 20.00 Rmt. 24.28

mortar 1:1 including neat cement finishing, watering etc. complete.

19 Providing 100 mm x 100 mm size vata in cement concrete (1:2:4) 30.00 Rmt 41.00

including water proofing compounds, smooth finish, curing, etc. complete

for the internal side of the sump.

20 'Providing and fixing water tight construction or expansion joints 150 mm. 120.00 Rmt. 379.50

dia. Wide thin ribbed PVC.

21 Brick masonry in cement mortar (1:5) using common burnt clay building 3.00 cu.m. 4526.81

bricks having crushing strength not less than 35kg/cm2 including

scaffolding,curing, etc. complete for walls, parapets, etc. at all levels.

Extra for brick work in superstructure above plinth level

upto floor two level

22 Brick work using common burnt clay building bricks having crushing 5.00 cu.m. 4245.09

strength not less than 35kg / Sq. C. M. in ramp, steps and Foundation &

Plinth in cement morter1:5 (1 cement : 5 coarse sand) including racking

out joints, curing, scaffolding required if any etc. complete, as directed.

23 Providing and fixing 40mm dia. GI pipe medium weight (3.17 kg/rmt 6.00 Rmt. 1784.00

approx ) quality as railing with angle iron support at 1.5 m c/c using 75 x

75 x 10 mm angles, 1.15 m long with three rows of pipes as railing

including necessary painting with two coats of approved quality oil paint

over one coat of approved primer including necessary welding, bolting

required, if any.

Ambaji Under Ground Drainage Under SJMMSVY

Civil Work of Construction of Sewage Pumping Station (SPS-01)

Item Description Qty. Unit Rate in Rs.

24 Supplying, cleaning, cutting, bending, welding, fabricating, erecting 3930.00 Kg 99.00

structural steel in position irrespective of locations and levels as per

drawing including handling and transport etc. complete including applying

two coats of primer red oxide and 'two coats of approved quality of paint

over it etc. complete as directed for gentry girder, platform, 'stairs,

chequered plate for cable trench etc.

25 Providing and fixing plastic moulded reinforced steps with 10 mm TOR 30.00 No. 87.00

steel bar with plastic 'polyproclene (P.P.) material (vergin) etc. complete.

26 Providing, laying and jointing in true line and level 110 diametre U.P.V.C 5.00 Rmt. 1053.73

(Type B) conforming to IS 13592-1992 with one end plain and other end

socketed with rubber ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with

each other with rubber lubricant, pipe shall be fixed on wall using of PVC

clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at

every 2000 mm center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent cement including cost

of all materials..

27 Providing and fixing 1.20 Metre high fencing with 2.0 Metre long M.S. 60.00 Rmt. 391.93

Angle posts 40mm x 40 mm x6 mm and oil painting 3 coats fixed at

Mt,C/c. with five Horizontan lines and two diagonals of galvanised steel

barbed wire weighting 9.38 Kg. per 100 Metre, strained and fixed to posts

with G.I,staples including fixing the postsin ground with 0.5 M x 0.5.M x

0.5 M. block in C.C1:5:10 etc complete.

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping Station (SPS-01)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

1 (A) MECHANICAL WORKS 2 Set 3,95,886

NON-CLOG SEWAGE SUBMERSIBLE PUMP MOTOR SET :

Supply, Installation, Testing and Commissioning (SITC) of Non-clog submersible

pump of following duty parameters along with LV AC submersible induction

motor air filled dry type pump-motor set shall be of materials of construction

and must have all required accessories viz. automatic coupling device, double

guide pipes, chain with shackles, Submersible Power & control cable (copper

flexible & stranded type conductor of reqd. cores & size for each pump motor

set) & length of 12 m long each run with necessary electrical termination

connection at junction box / starter panels, RCC foundation with duck foot bend

for auto coupling & delivery bend and PMU etc. as per equipment data sheet

and detailed technical specifications and also including in scope any other parts /

accessories / fittings required to complete the work in all respects & satisfactory

operation of pump set.

Pump Capacity: 80 m 3/hr, (1W+1S)

Max. RPM: 1500 &

Motor Rating: Minimum 18.5 kW (or higher as recommended by pump

Over all Minimum Acceptable Efficiency at Duty Point: 45%.

2 VALVES: 2 Nos. 6,433

SITC of CI / DI Double Flanged, Manually Operated Sluice Valve confirming to IS

14846, PN 1.0 of following sizes with SS 304 seat rings and SS spindle with hot

dipped galvanised hardwares, bolts, nuts & washers etc. as per IS and

Specification & complete the work in all respects.

Size: 150 mm NB (on delivery of each pumpset)

3 SITC of Non slam, flanged, CI/DI Single Door type Non Return Valve conforming 2 Nos. 8,612

to IS 5312 (Part-1), PN 1.0, having DI/CI body and door, CF8M seat rings

alongwith all necessary hardwares as per specifications and complete in all

Size: 150 mm NB (on delivery of each pumpset)

4 SITC of Flange ends Expansion Bellow (PN 1.0) as per EJMA standards and as per 1 No. 4,656

specs. and complete in all respect.

Size : 150 mm NB X 300 mm L (on Common Header)

5 DI PIPES 500 kg 155.00

SITC of double flanged DI Pipes confirming to IS 8329-2000, class K9 with

connections complete for delivery and header lines and as per specifications. The

scope also includes connection with main header/rising main & complete the

work in all respects.

Size: 80 mm dia. to 300mm dia.

6 DI FITTINGS 200 kg 155.00

Supply, installation, connection with delivery / header, testing and

commissioning of Flanged DI Fittings and Specials like 90 deg. Bend, Drilled /

Drilled Blind Flanges, Reducer / enlarger, Tee, etc. as required to complete the

piping and connection of pumps with header/rising main conforming to IS

& complete the work in all respects.

Size: 80 mm to 300 mm dia.

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping Station (SPS-01)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

7 Flanged Joints of Pipes, Fittings and Specials: 8 Nos. 611

Supply, Installation, Making of Flanged DI /CI / GI / MS Pipes, Fittings and

Specials Joints with all jointing materials, rubber packing, nut bolts, labour etc.for

complete connection.

Size : 150 mm dia.

8 --- Item description as above --- 1 No. 837

Size : 200 mm dia.

9 MONORAIL EOT WITH ELECTRIC CHAIN HOIST 1 Set 1,76,240

SITC of Electrically Operated Chain Hoist & Electrically operated Trolley, suitable

to operate on Mono Rail Girder having motorised motion in vertical lifting &

cross travel, manufactured as per IS:6547-1972-Class-II & IS-3177- Class-II,

complete with electrically operated chain hoist & Electically operated geared

trolley, brake, chain-gear, motors, safety device, pendant push button, starter

panel, cables from motor to starter panel and all other required accessories like

limit switches, panel, power supply system (Fastoon cable type), fasteners, epoxy

painting, etc. tested for over load as per IS complete as per specifications and

complete in all respect.

Capacity : Min. 1.0 Ton. (At Pump House)

Lift : 11.00 m as mini. or as per site req.

Bay Length : 5.5 m min. or as per site req.

(w/o MONORAIL GIRDER & MS supporting structure)

10 SITC of Manual Operated Chain Pulley Block (CPB) as per IS 3832 duty with 1 Set 14,400.00

geared traveling trolley with 50 % over load test, load chain alloy steel Gr.80, as

per IS 6216, etc. as per IS, complete as per specifications and complete in all

Capacity : 1 Ton. (Above Manual screen)

'Lift : 6.00 m as mini. or as per site req.

(w/o MONORAIL GIRDER & MS supporting structure)

11 SLUICE GATE 1 No. 1,34,720

SITC of Manually operated C.I. Sluice Gate conforming to AWWA C 501 or IS :

13349 - 1992 Class - 1 with rising spindle, single faced, wall thimble mounted,

handwheel, flange back frame, head stock, Spindle with supports brackets

having length as specified or to suit site condition, suitable for seating as well as

unseating water head, complete in all respect.

Gate Size : 300 mm X 300 mm - approx. 4.0 m spindle length (at inlet chamber) -

Conventional Bottom Closing or suitable Closing

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping Station (SPS-01)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

12 SITC of Box Type Manual Mesh Screen having following size, made of SS 304 1 Set 1,07,770

material having round bars of size 9.0 mm dia with clear bar opening as specified

here below, suitably welded in outer frame of equal Leg SS angle of size 50 mm x

50 mm x 6 mm thick or higher, with intermediate support at required locations,

complete as per specs. & shall also including followings:

The screen shall be with SS perforated Screening Material Collection Box at

bottom end of Screen having size as specified, fabricated from 3 mm thk SS

sheet, screen shall be suitable to slide complete screen through rollers between

existing guide passage of MCP 400, embedded/ fixed in wall on both sides of

RCC wall up to top of chamber with all necessary hardware, SS nuts, bolts &

wahsers, sacrificial Brass lugs on sides, min. two lifting lugs/hooks & SS lifting

chain having intermediate link/chain of 100 mm dia. at every 1.5 m distance with

shackle, etc. complete in all respects and provided with 1 set of cleaning rake

with each screen, complete as per specification and complete in all respect.

Screen Size: 600 mm (W-or actual chamber width as per site ) x 600 mm (H) x

Box Size: 600 mm (W-or actual screen width) x 100 mm (H) x 300 mm (D)

Opening: 50 mm x 50 mm sq. opening

Note : Screen suitable for 700 mm wide screen chamber or to suit site

(w/o Guide channel & MS supporting structure)

13 Providing, Supply of Structure Steel at site of work with freight, loading, 1500 kg. 64.838

unloading carting, etc. including all taxes and duties complete such as joints,

channels, angles, Iron Rails, ISA/ISMC/ISMB/MS flat, Plates, Chequered plates

(min. 7 mm thickness) for cable trench etc. required for support structure of all

Electro-mechanical equipment, piping, etc. for support on floor / wall / beam /

brackets etc. as per tender and IS.

14 Labour Charges for lowering, laying, Fixing with fabrication various size section of 1500 kg. 11.365

MS such as joints, channels, angles, Iron Rails, ISA/ISMC/ISMB/MS flat, Plates,

Chequered plates, for cable trench etc Complete with two coats of red oxide and

two coats of approved colour shade of epoxy paint as per relevant IS and as per

15 (B) ELECTRICAL WORK 1 Set 39,391.46

TPN MCCB (For LT Service Obtaining Requirement)

SITC of 250A TPN microprocessor MCCB, LSIG (50kA) with inbuilt O/L, S/C & E/F

protection with Extended rotary handle, Terminal spreader, Auxiliary change

over & Trip contact, with Outdoor Enclosure with canopy 2mm thick

Single/double door & Wall mounted/ stand mounted as per site requirement

(with incoming & outgoing cable entry at bottom )with Cable end boxes with RYB

indicating lamp, Digital voltmeter, VSS,ON,OFF & Trip indicating lamp etc as per

Power supply company requirements & location. Including all civil works for

fixing of panel on wall.

(Wall mounted at Location as per PSC req.)

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping Station (SPS-01)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

16 MEDIUM VOLTAGE PANEL BOARD (PMCC /APFC) 1 Set 5,79,000.00

SITC of PMCC Panel (50kA), compartmentalized, Stand mounted as per site

condition and requirement with required modification / rectofication works as

required, operating height maximum 1800/1900 mm, Extensible on both ends,

suitable for Manual & Auto operation -Local & through PLC/SCADA operation as

per site conditions complete in all respects as per Tender SLD / Specification / IS

and including following as minimum:

(1) One no. Incoming feeder FP 250A Microprocessor MCCB (50kA), LSIG, with

inbuilt O/C, S/C, & E/F protection for I/c with Digital Voltmeter, Voltmeter

selector switch, Digital Ammeter, Ammeter selector switch, Power Factor Meter,

MFM with RS-485 of Class-0.5, Indicating lamps R,Y,B,On,off,Trip, 3nos. 250A/5A,

Cl.-0.5 metering CT, CL 0.5 CT for APFC relay etc. Constant voltage/control

voltage transformer 1500VA, 415V/230V AC, with tapping +/-5% in steps of 2.5%,

32A DP MCB complete in all respects.

(2) 250A TPN Main Aluminium busbars. (main busbars size with current density

(3) 18.5 KW STAR -DELTA STARTER FEEDER (SUBM.): 2 NOS

18.5 KW or higher as per pump manufacturer recommendation Star-delta starter

with 80A TPN Thermal magnetic MCCB with Adjustable O/L & Adjustable S/C

protection, 80A AC3 duty contactors (3 nos.), O/L Relay, star-delta timer,

Ammeter with ASS, Resin Cast CT Cl: 0.5(3 nos.),SPP, PMU, A/M, L/R switch, ON,

OFF, TRIP Indication & Start, E-Stop & Reset pushbutton etc. for S/D starter.

complete in all respects.

(4) 63A TPN TM MCCB FEEDER : 2 Nos. ( 2 nos. spare)

Each feeder comprising of 63A TPN Thermal Magnetic (TM) MCCB, with

indicating lamp etc.

(5) 32A TPN TM MCCB FEEDER : 2 Nos. (1 no. for EOT with ECH at PH., 1 no.

Each feeder comprising of 32A TPN Thermal Magnetic (TM) MCCB, with

indicating lamp etc.

(6) 63A TPN TM MCCB FEEDER FOR ALL MCB FEEDERS: 1 set:

17 Incomer: 63A TPN

SITC of Lighting Thermal Magnetic

Distribution (TM)asMCCB,

Board (LDB) under:with indicating lamp etc. 2 Nos. 7,947.39

SITC of 3 Phase 4 Wire 4P, double door Prewired LDB each for Indoor Lighting &

Outdoor Lighting Suitable to house :

Incoming: 32A FP, ELMCB (30mA)

Outgoing: 20A SP MCB (9 nos.) & 16A SP MCB (9 nos.)

18 LOW VOLTAGE (LT) CABLES 25 Mtr. 783.00

Supply, laying, testing and commissioning of 1.1 kV, A2XFY(X)/2XWY(X) XLPE

insulated (IS 7098) AL / Cu stranded conductor, Extruded innersheath cables as

per specification & IS.

The cable when laid outside the building shall be laid underground in trench

with brick & sand protection/in DWC pipes as per specified method and shall be

laid in prepared trench/ on cable tray when laid inside the building.

SITC of 3.5C x 240 sq. mm. A2XFY(X) Cable (1 run for MCCB to PMCC panel)

19 SITC of 4C x 6 sq. mm. A2XFY(X) Cable (For 1 no. Indoor LDB, 1 no. Outdoor LDB) 50 Mtr. 78.00

20 SITC of 4C x 2.5 sq. mm. 2XWY/2XFY(X) Cable (1 no. for EOT with ECH at Pump 100 Mtr. 283.15

House & for 2 nos. street light)

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping Station (SPS-01)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

21 SITC of Single core 95sq. mm. PVC insulated circular unsheathed copper 20 Mtr 919.45

conductor flexible Cable (For Power supply Metering Panel to I/c MCCB Unit)

22 CABLE END TERMINATION AND CONNECTION: 2 Nos. 838.00

SITC of Double compression Ni-Plated brass cable glands and crimping type

Bimetallic lugs / sockets with necessary tools and equipments as specified in

specifications and IS. The glands and lugs / sockets shall be suitable for cable

size and type mentioned below & as per specifications.

1) Earthing the glands and armouring with earthing clamp and jumper and also

connecting to common earth bar.

2) The job also includes, if necessary, supply & fixing of extension busbar of same

material on MCCB or panel board terminal / connector to connect more than

one no. of parallel cables or to connect higher size cable to lower size unit. The

job also includes earthing the glands and armour of the cable with common

earth bar or flexible copper mesh.(Cable termination qty. shall be as per site

SITC of 3.5C x 240 sq. mm. A2XFY(X) Cable (1 run for MCCB to PMCC panel)

23 4C x 6 sq. mm. A2XFY(X) Cable (For 1 no. Indoor LDB, 1 no. Outdoor LDB) 4 Nos. 111.00

24 4C x 2.5 sq. mm. 2XWY/2XFY(X) Cable (For 1 no. for EOT with ECH at Pump House 6 Nos. 68.93

& for 2 nos. street light)

25 Single core 95sq. mm. PVC insulated circular unsheathed copper conductor 10 Nos. 49.84

flexible Cable (For Power supply Metering Panel to I/c MCCB Unit)

26 CABLE TRAY 50 Mtr. 584.34

SITC of G.I. (hot dip galvanised )Ladder type medium duty (2mm thick) Cable

Tray with necessary bends, tees, reducers, covers and clamps for fixing. All

material shall be Hot dip galvanised as per Specification. And including all

300 x 100 mm - Ladder type

27 150 x 50 mm - Ladder type 70 Mtr. 292.70

28 Supply, laying and erection of 75 mm ID approved make Double Walled 50 Mtr. 158.00

Corrugated pipes (DWC) of polyethelene (confirming to IS-14930 II) with

necessary connecting accessoies of same material at required depth for laying of

cable below ground / road surface for enclosing cable and back filling the same

to make ground as per original. (LT cable etc)

29 Cable Trench, Laying & Installation of Cable: Making cable trench in soft soil of 70 Mtr. 48.78

suitable width of 90cms deep for laying cable, Sand cushioning and brick

protection on sides and on top all over the run and back filling the same and

making the surface as normal ground as per IS & Specification. (For laying of LT

cable in ground)

30 Cable Protection/ Covering in Trench: Cable Covering with second class bricks or 20 Mtr. 141.05

cement tiles laid cover the cable (top) & also on both side with sand

bedding/cusioning of 75mm.& covering of 150mm Layer of sand above cable

(16 bricks per meter.) as per IS & Tender Drg/ Specification. (For HT/LT cable

protection) complete in all respects as instructed by EIC.

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping Station (SPS-01)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

31 CHEMICAL EARTHING SYSTEM 2 Set 11,123.58

SITC of Maintenance free chemical earthing (copper) with earthpit of minimum

bore size dia. 225mm Safe Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS-3043:1987 /Tech spec. made of corrosion free Pipes having Outer pipe

dia of 48 mm having 250 Micron copper plating, Inner corrosion free Hot dip

galvanised (80 to 100 micron) pipe dia of 26 mm with copper flat strip type

connection terminal 14mm dia with constant ohmic value surrounded by highly

conductive corrosion resistant chemical compound with high charge dissipation

suitable for electrical installation & of 3Mtr. length of Pipe with two nos. 25Kg.

bag of Back filling compound. (2nos. for ICP/PLC Earthing)

NOTE: Earthing Resistance value & date shall be painted on the chamber cover.

32 SITC of Maintenance free chemical earthing with earthpit of minimum bore size 4 Set 7,450.01

dia. 225mm Safe Earthing Electrode consisting Pipe-in-Pipe Technology as per IS-

3043:1987 /Tech spec. made of corrosion free Hot dip Galvanised (min

Microns) Pipes having Outer pipe dia of 76 mm , Inner corrosion free Hot dip

galvanised (80 to 100 micron) pipe dia of 26 mm with copper flat strip type

connection terminal 14mm dia with constant ohmic value surrounded by highly

conductive corrosion resistant chemical compound with high charge dissipation

suitable for electrical installation & 3Mtr. length of Pipe with two nos. 25Kg. bag

of Back filling compound. (2 nos. for LT panel & 2nos. for all elect. Equipments)

NOTE: Earthing Resistance value & date shall be painted on the chamber cover.

33 SITC of 50mm(w) x 8mm(T) etc. sizes as required, HOT dip galvanized GI Strip 230 Kg. 81.66

including supply & fixing using GI spacers, saddles when laid inside the building

and inclusive of excavation & refilling of earth when laid outside the building &

interconnection with earth pit & all electro-mechanical equipments.

(50X6 G.I Strip wt.2.3 kg/m, 2.3x100Mt.=230kg.)

34 Supply, laying and erection of 25mm(w) x 3mm(T) etc. sizes as required, HOT dip 12 Kg. 81.66

galvanized GI Strip including supply & fixing using GI spacers, saddles when laid

inside the building and inclusive of excavation & refilling of earth when laid

outside the building & interconnection with earth pit & all electro-mechanical

equipments. (25X3 G.I Strip, 0.6 Kg/m, 0.6x60Mt.=12Kg.)

35 Supply, laying and erection of 25mm(w) x 3mm(T) etc. sizes Copper Strip 23 Kg. 834.61

including supply & fixing of bolts, saddles when laid inside the building and

inclusive of excavation & refilling of earth when laid outside the building &

interconnection with earth pit & PLC Panel (25X3 Cu. Strip, 0.761 Kg/m, 0.761 x

Copper Bolt,Nuts ,Washers shall be used for Connecting Earth electrode to

individual eqp. Bitumen shall be used at the place of joint/welding. (For PLC

Panel to Earthing)

36 SITC of HOT Dip Galvanized iron strip wire 8 SWG (For LDB,LCS, etc.) 10 Kg. 81.66

(8 SWG G.I Strip, 0.103 Kg/m, 0.103 x 100Mt.=10.3 Kg.)

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping Station (SPS-01)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

37 INTERNAL WIRING 50 Mtr. 82.72

SITC of Mains & outlet points wiring with 1.1 kV grade FRLS PVC insulated ISI

marked flexible stranded copper conductor wires with medium class min. 25mm.

dia. Electrical grade PVC pipe and accessories to be erected concealed in / to be

run on surface / wall / ceiling with following sizes as mentioned below. The unit

rate wirings shall be with connector, PVC junction box, wires, holder, ceiling rose,

angle holder, switch, sockets, switch board, brass chromium / cadmium plated

machine screws, phase and neutral wires, green Earth continuity wires etc. as

required to complete wiring from LDB panel to the final outlet termination

points. The wiring shall be as per IS:732, IS:4648 and as per tender

specification / IS.

(a) SITC of Mains wiring with 3 wire 1.5 sq.mm.

38 same as above, but (b) SITC of Mains wiring with 3 wire 2.5 sq.mm as per tender 50 Mtr. 101.81

specification & IS.

39 same as above, but (c) SITC of Mains wiring with 4 wire 1.5 sq.mm as per tender 80 Mtr. 91.20

specification & IS.

40 same as above, but (d) SITC of Mains wiring with 4 wire 2.5 sq.mm as per tender 80 Mtr. 126.20

specification & IS.

41 SITC of Point wiring for Light / fan / Bell / Primary Point with 2nos. 1.5 sq. mm & 13 Nos. 345.72

earth wire of 1.5 sq. mm (green) both are of ISI marked 1.1 kv grade FRLS PVC

insulated multistrand copper wires , pipe to be erected concealed in flushed on

wall / ceiling, complete with 6A Tissino Type ISI marked flush type switch / bell

push & accessories erected on metal / PVC Box covered with 3 mm thick PC

(Polycarbonate) / Acrylic sheet with necessary lamp holder / ceiling Rose / H. D.

connector as directed with medium class Rigid PVC pipe & accessories.

42 SITC of 6A independent Plug with 2nos. 1.5 sq.mm Cu. Mains size wiring & 2 Nos. 305.42

earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multistrand copper wires with medium class Rigid PVC pipe and

accessories to be erected on wall / ceiling, complete with ISI marked 3 / 5 Pin

socket and tissino type switch erected with earth continuity connection erected

on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / Acrylic sheet.

43 SITC of 6/16A independent Plug with 2nos. 4 sq.mm Cu. Mains size wiring & 2 Nos. 599.18

earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multistrand copper wires with medium class Rigid PVC pipe and

accessories to be erected on wall / ceiling, complete with ISI marked 3 / 5 Pin

socket and tissino type switch erected with earth continuity connection erected

on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / Acrylic sheet. (1

no. LT Room cum Pump House)

44 SITC of One 300/380 mm dia. Ex fan 16A independent Plug point near Ex. Fan 2 Nos. 599.18

with 2nos. 4 sq.mm Cu. Mains size wiring & earthwire of 1.5 sq.mm (green) both

are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires with

medium class Rigid PVC pipe and accessories to be erected on wall / ceiling,

complete with ISI marked 3Pin socket and tissino type switch erected with earth

continuity connection erected on Metal / PVC box covered with 3 mm thick

PC(Polycarbonet) / Acrylic sheet. Plug point shall be near Ex.Fan.

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping Station (SPS-01)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

45 SITC of 380mm sweep 1400 R.P.M exhaust fan, capacitor type, having double 2 Nos. 3,236.65

ball bearing, M.S.blades, mounting frame, forearms, suitable to operate on

230V,50 HZ AC supply conforming to IS: 2312.Fan shall be painted with epoxy

grey colour controlled by one 6 A flush type switch on board and 6A plug point

46 SITC of Single Phase 20A 3 Pin Metal clad Industrial Type Socket with plug top 2 Nos. 820.00

and 20A SPMCB, suitable for flush mounting, in 16 SWG MS box of suitable size

and covered with 3 mm thick electrical grade hylam sheet or equivalent ISI

marked Electrical grade Bakelite sheet and earthing with 2.5 sq.mm insulated

copper wire run inside the conduit including interconnections etc. complete as

(1 no. LT Room cum Pump House)

47 SITC of Sheets steel powder coated weather proof enclosure with One no. 32A, 1 No. 809.16

415V 4P MCB for Motor & Inductive load (C Curve) having 10 KA breaking

capacity & confirms to IS: 8828. (1 no. for EOT with ECH at P.H)

48 1200mm sweep ceiling fan, capacitor type, having double ball bearing 450mm 2 Set 619.33

down rod, canopies, shackle, rubber bush, blades, electronic speed regulator,

suitable to operate on 230V,50Hz AC supply conforming to IS: 374/1979.Fan shall

be painted with white colour.(1 no. LT Room)

49 LED LIGHT FIXTURES & LIGHTING: 4 Nos. 231.19

SITC of Indoor wall mounting 20Watt or up to 25% higher wattage LED 4 feet

Tube Light indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled

on single MCPCB, with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA polyester powder coated and high U.V. &

corrosion resistance with diffuser and/or Polycarbonate optics with company

120 to 300 V,Power Factor more than 0.9, THD < 20 %,

CCT 4000 K to 6500K, Uniformity ratio >0.7,

Luminaries efficacy> 85 lumens/watt

LED driver efficiency > 85 %

(Each fitting required LM-79 & LM-80 Certificates)

Tube Light with integral / non-integral driver, Surge-4KV,IP-20, 4 feet, Cat-III

50 Item description as per above SITC of 7 watts LED Lamps integral type,cool white 1 No. 1,676.65

with PC diffuser suitable for B22 LAMP holder (1 no. LT Room cum Pump House)

51 SITC of 40W LED Surface / Wall mounted LED Flood Light fittings with High 4 Nos. 5,454.15

power White LEDs wattage of 1Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses with company

mark/name engraved or embossed

120 to 300 V,Power Factor more than 0.95, THD < 20 %, CCT 5000 K to 5700K,

Uniformity ratio >0.45, Luminaries efficacy> 85 lumens/watt . LED driver

efficiency > 85 %.

( Each fittings required LM-79 & LM-80 certificates)

(IP-65), Surge -4KV Cat-III

For Indoor use: (at Pump House)

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping Station (SPS-01)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

52 SITC of 'B' class galvanised iron pipe 32 mm outside dia 45 cms long duly welded 9 Nos. 586.46

on 20 cms x 20 cms x 3 mm thick M.S. base plate, erected on wall or corner for

mounting luminaries with necessary hardware materials duly painted for wall

mounting indoor flood light fixtures on Wall of Buildings & post top lantern.

53 EXTERNAL LIGHTING (Flood LIGHT): 5 Nos. 6,392.69

SITC of 70W LED Wall mounted LED Flood Light fittings with High power White

LEDs wattage of 1Watt and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die cast aluminum housing with

smooth finish powder coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses with company mark/name engraved or

120 to 300 V,Power Factor more than 0.95, THD < 20 %, CCT 5000 K to 5700K,

Uniformity ratio >0.45, Luminaries efficacy> 85 lumens/watt . LED driver

efficiency > 85 %.

( Each fittings required LM-79 & LM-80 certificates)

(IP-65), Surge -4KV Cat-III

For Outdoor use: (for area lighting)

54 EXTERNAL LIGHTING (STREET LIGHT): 4 Nos. 11,223.27

SITC of Street Light Pole, steel tubular swaged type, 7.5 meter long with single

arm & M.S.base plate with pipe cap and over hung 1.5 m long having dia to suit

the socket of 240V LED street light fixtures. Street light pole unit rate shall be

with (i) IP 65 SMC box of size 20 x 15 x 15 cms. with MCB & terminal strip inside

the box with hinged/sliding door (ii) 50mm dia, B class GI pipe bracket

min.1.5mtr long for Incoming & outgoing cable (iii)MS Cable Clamp of 25 x 3mm

(iv)SITC of 1.5 Mtr.single Arm bracket of medium duty MS pipe of 4.2 cms. Out

side dia complete with suitable sleeve tubing 45 cms. long of required size of

pole top etc. and having spread of 1.5.mtr. length with 110 deg.(v) Complete

painted with one coat of Red oxide / PU base primer and two coats of Aluminium

/ PU paint for Pole,Arm, pipe etc.

55 SITC of 70W LED Street light fittings with High power White LEDs wattage of 4 Nos. 6,274.98

1Watt and above assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminum housing with smooth finish

powder coated and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses with company mark/name engraved or embossed

120 to 300 V,Power Factor more than 0.95, THD < 20 %, CCT 5000 K to 5700K,

Uniformity ratio >0.45, Luminaries efficacy> 85 lumens/watt . LED driver

efficiency > 85 %.

( Each fittings required LM-79 & LM-80 certificates)

Street Light (IP-65), Surge -4KV, 70 watt Cat-III

56 SITC of M-20 / 1:2:4 cement concrete foundation for Street light pole & 70 % 4 Nos. 1,357.44

PCC from bottom including excavation for the pole of size 60 x 60 x 120 cms.

Deep in below ground level with plinth of 45 cms x 45 cms(or 45 cms dia x

cms) high upper ground level with necessary curing and finishing in approved

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping Station (SPS-01)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

57 SAFETY ACCESSORIES 2 Nos. 9,105.45

SITC of following safety accessories complete with necessary fixing brackets,

other accessories and tools etc. as required to complete the job.

Supply & Erecting carbon dioxide (CO2) fire extinguisher of 6.5kg capacity with

necessary clamps made from 50 x 6 mm M.S. Flat with nut & bolts grouted in

(2 nos. LT Room cum Pump House)

58 Supplying of standard first AID box with antiseptic cream, medicine for use on 1 No. 314.97

wounds due burn, crepe bandage, guage bandage, medicated ready to use

bandage (Band-aid) adhesive tape for medicinal user, scissors, antiseptic solution

(Savlon or similar) etc. (All above contents shall be of standard makes)

(1 no. LT Room cum Pump House)

59 Supply & fixing of printed instruction (First Aid) Chart both in English and 1 Nos. 136.80

Gujarati and duly framed with front glasses, for treatment of person suffering

from electric shock. (For 1 no. For LT Room)

60 Supply and fixing of 20 W fluorescent lamp operated emergency light with 1 Nos. 2,670.00

maintenance free battery for 3 hours operation during mains power failure.

(For 1 no. LT Room)

61 Supply and laying of Synthetic Insulating Mat of Class - A of min. thickness 2mm 4 Sq.mtr. 1,078.53

as per IS:15652 and with good electrical insulation property for 1.1KV/3.3KV as

per site requirement. (For LT Panel)

62 (C) INSTRUMENTATION WORK 2 NOS. 5,413.00

PRESSURE MEASURING SYSTEM

Supply, installation, testing & commissioning of Diaphragm Type pressure guage

having 150 mm dial with necessary fittings/accessories in SS

(manifold valve, nipples etc.) complete in all respects and as per specs.

Range : 0 - 6Kg/cm2 (at each pump's delivery side )

63 LEVEL MEASURING SYSTEM 1 NO. 84,568

Supply, installation, testing and commissioning of Hydrostatic type Level

Transmitter with Local Indicator and 4-20 mA Retransmission output with

meter cable, Junction box, all mounting accessories, hardware, Fixing of 2.5" size

UPVC pipe in Sump for installation the Hydrostatic sensor, Clamp,etc. complete

in all respects with local and remote display at PLC/HMI, as per specification and

having following measurement ranges for Sewage application:

Meas. Range: upto 10 m (at Sump)

64 LARGE SIZE LED DISPALY FOR SUMP LEVEL TX. 1 NO. 20,160

Supply, installation, testing and commissioning LED diplay 8" size (320 mm H X

650 mm W X 50 mm D) with 4-20 mA Input at Wet Well to monitor the level of

Wet Well from distance, all required accessories, etc. complete in all respects as

per specification.

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping Station (SPS-01)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

65 Supply, installation, testing and commissioning of Float type Level Switch along 1 NO. 12,802.00

with 10 mtr. Cable and WP Junction Box (at wet well for dry run protection of

pumps ) complete in all respects and as per specification.The scope also includes

providing 4" flanged , puddle pipe approximate 300 mm long including fixing of

the same in civil structure slabe of pump house for mounting of level switch.The

work also include all necessary work like make hole,repair / modification in slab,

66 FLOW MEASURING SYSTEM 1 NO. 82,972.00

Supply, installation, testing and commissioning of remote type Full Bore

Electromagnetic Flow Meter comprising of IP-68 Sensor, IP66 remote

transmitter with 20 m cable between sensor and transmitter along with all

mounting accessories, hardware, etc. complete in all respect and as per specs

and shall have following size and measurement range. The scope also includes

necessary connection with header pipe.

Meter Size : 150 mm NB

Pipe size: 150 mm NB

67 PLC BASED CONTROL PANEL FOR SPS 1 LOT 7,30,296.00

Supply, Installation, Testing & Commissioning of PLC Based Instrument control

Panel with panel mounted 10 " colour touch screen HMI, 4G or Latest GPRS

modem with (Ethernet port + SIM Slot) for Remote data transmission to central

SCADA of client in future , Communication port for MFM. Instrument Control

Panel '(PLC Enclosure / Panel ) with necessary PLC based logic and wiring , Min.

kVA Online UPS + CVT (with 60 min min backup ), etc. complete in all respects

and as per specs with PLC having minimum I/O count of 20DI / 12 DO / 4AI

/2AO. These are the minimum IO requirement if any other IO,s required to

complete the work contractor shall be provide the same without any extra cost.

68 INSTRUMENT CABLE & ACCESSORIES 50 MTR. 146.00

Supply, Laying, Installation, Connection, Termination, Testing & Commissioning

of Instrument Cables, along with cable glands, lugs, cable trays, required junction

boxes, fittings and accessores as per specs. The unit rate shall include.

(a) Supply, loading & unloading of the cable at site from store.

(b) Shifitng of cable from site store to place of installation.

(c) Fixing of cable clamps, brackets, supports, route markers etc. where ever

required to fix the cables safely.

(d) Excavation, back filling and levelling of ground alongwith laying of fine sand,

protection bricks and other necessary civil material for laying cables outside the

(f)Testing and submission of sketches & reports of all the cables laid.

69 CONTROL CABLE 50 MTR. 330.00

70 SIGNAL CABLE 100 MTR. 133.00

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping Station (SPS-01)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

71 INSTRUMENT CABLE TRAY 10 MTR. 476.00

G.I. Perorated type cable tray shall be made out of galvanized mild steel sheets

of 2 mm thickness with required asccessories . All material shall be Hot dip

galvanised as per IS 2629 (as mentioned in specification and tray hardware shall

200 X 25 mm - Perforated type

72 50 X 25 mm - Perforated type 10 MTR. 291.00

73 CABLE END TERMINATION AND CONNECTION : 4 NOS. 160.00

Supply, fixing, connection, testing and commissioning of double compression

brass cable glands and crimping type Bimetalic lugs / sockets with necessary

tools and equipments as specified in specifications and IS complete in all

respects. The glands and lugs / sockets shall be suitable for cable size and type

mentioned above. The job also includes earthing the glands and armour of the

cable with common earth bar or flexible copper mesh as applicable.

74 CONTROL CABLE 8 NOS. 230.00

75 SIGNAL CABLE 6 NOS. 160.00

Ambaji Under Ground Drainage Under SJMMSVY

Rising main from SPS-01 to Gravity line of TSPS

Item Description Qty. Unit Rate in Rs.

Excavation for trenches with shoring & strutting if required as per

required gradient and line including all safety provision using site rails

and stacking excavated stuff including up to all required lead cleaning

the site etc. complete for all lift and strata as specified.

I) In all sort of soils and soft murrum

1.1 II) In hard murrum, boulders incl. macadam road. 164.0 cu.m. 155.25

1.2 III) In soft rock and/or masonry in CM or L M or Lime Concrete. 164.0 cu.m. 187.45

1.3 IV) In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking, 246.0 cu.m. 427.80

chiseling, or by chiseling/breaking only.

Providing bedding incl. ramming, watering, levelling, consolidating etc.

complete as per standard and instruction of engineer incharge.

(II) As above with Murrum brought from outside including all lead

Providing and supplying D. I. K-9 grade pipes for following nominal bore

diameter with internal cement mortar lining including all taxes,

insurance, transportation, freight charges, octroi, inspection charges,

loading, unloading, conveyance to departmental stores, stacking etc.

complete. (IS 8329-2000). For sewerage project cement mortor lining

shall be with sulphate resistance cement.

200 mm dia DI K-9 with EPDM Gasket

4 Lowering, laying and jointing C. I. S & S Spun pipes suitable for Tyton 700.0 Rmt 113.85

joints / Mortar lined D. I. Pipes of various classes with CI / MS specials of

following diameters in proper position, grade and alignment as directed

by Engineer-in-charge including

hydraulic testing etc. complete.

200 mm dia DI K-9 with EPDM Gasket

Manufacture, Supply & Delivery of Ductile Iron Flange socket spigot

bends, tees, reducers or any other specials as per BS-EN-545/1995 Class-

A series K12 suitable for use with D.I. Pipes manufactured as per

IS:8329/1994 delivery of specials is to be made to GWSSB store or site of

works any where in Gujarat including all taxes, loading, unloading,

carting, stacking, insurance, inspection charges, octroi etc. complete.

Socket & Spigot Type 80 to 300 mm dia

Providing, supplying, Delivery and fixing of Water Hammer Control

Devices for use on various pumping main of following class and

diameter including all taxes, insurance, transportation, freight charges,

octroi, inspection charges. loading, unloading, conveyance to

departmental stores, stacking etc. complete. a) 200 mm dia Zero Velocity

Valve with bypass arrangement with CI Body (Class-15)

6.1 200 mm dia Air Cushion Valve with Cast iron body (Class-15) 1.0 No. 126945.00

Ambaji Under Ground Drainage Under SJMMSVY

Rising main from SPS-01 to Gravity line of TSPS

Item Description Qty. Unit Rate in Rs.

7 Providing, supplying ISI mark Cast Iron D/F Sluice Valves of following 1.0 No. 9813.00

class and diameter including all taxes, insurance, transportation, fright

charges, Octroi Inspection charges, loading, unloading, conveyance to

site stacking, etc. complete.

PN-1 with hand wheel /cap operated (PD Type short body)

Lowering, laying & jointing in position following C. I. / D/F Sluice Valves

including cost of all labour, jointing material, including nut bolts & giving

satisfactory hydraulic testing, etc. complete.

PN-1 with hand wheel /cap operated (PD Type short body)

Providing, supplying,& fixing CI Tamper proof Air valves with SS

Float gun metal nozzle of approved make & quality of following class and

diameter including all taxes, transportation, freight charges, octroi,

inspection charges, loading, unloading, conveyance to the departmental

stores, stacking etc. complete.

With Isolating Sluice Valve PN

8.1 Lowering, laying & jointing in position following air Valves including cost 2.0 No. 435.85

of all labour, jointing material, including nut bolts & giving satisfactory

hydraulic testing, etc. complete.

With Isolating Sluice Valve PN

9 Construction of Valve chambers in brick masonary, locally available in 5.0 No. 13053.65

C.M. 1:6, foundation concrete 150 mm thick in C.C. 1:4:8 of trap metal

size 25 mm to 40 mm thick, inside cement plaster in C.M. 1:3 and cement

pointing outside in C. M. 1 :3 & top cover of precast RCC slab 150 mm

thick upto 1 mt. depth from G.L. but excl. cost of excavation and refilling.

With cast in situ RCC slab in two piece, with 23 mm thick brick masonary

wall in C.M.1:6, With precast slab in two parts 15 mm.

Size of chamber 1.3m x 1.3 m and 1.0 mt. deep.

9.1 for 1 m. extra depth 2.0 Rmt. 6996.60

10 Providing and casting in situ C.C. in grade M-15 (approx. corresp. to prop. 3.0 cu.m. 5441.80

1:2:4) (proportions as per mix design or as per Table 9 of IS456 2000 in

masses by weigh batching ) using granite, quartzite trap metal of size

mm to 20 mm for RCC work, including scaffolding centering, form

work, needle vibrated consolidation, curing comp. (excluding cost of

reinforcement and neat finishing) with centering and

shuttering/deshuttering etc. comp. for structure for other than water

Footing (without form work)

Ambaji Under Ground Drainage Under SJMMSVY

Rising main from SPS-01 to Gravity line of TSPS

Item Description Qty. Unit Rate in Rs.

11 Providing and casting in situ C.C. in grade M-20 (proportions as per mix 85.0 cu.m. 6348.00

design or as per table 9 of IS 456 2000 in masses by weigh batching )

using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work,

including scaffolding centering, formwork, needle vibrated consolidation,

curing complete (excluding cost of reinforcement and neat finishing)

with centering and shuttering/deshuttering etc. complete for structure

other than water retaining (Below G.L)

RCC ( For Thrust block & encasing)

Supplying cutting, bending, binding and placing in position steel as per

plan and design and as per ISS 2502 including cost of steel and binding

wire for reservoirs/structures only including lift up to 6 meter height or

depth below G.L. for all diameters

Do – deformed (TMT) bars confirming to relevant IS Fe – 500 grade for all

Refilling the pipeline trenches including ramming, watering,

consolidating disposal of surplus stuff as directed within a radius of 3 Km.

Refilling as Directed

13.1 do with selected soil brought from outside including all lead 454.0 cu.m. 201.25

14 Providing and cast in situ C.C. in grade M-30 proportions of ingredients 2.0 cu.m. 9295.45

as per mix design by weigh batching using granite, quartzite trap metal of

size 12 mm to 20 mm

and or 6 mm to 12 mm including scaffolding centering formwork, needle

vibrated consolidation, curing and hydraulic testing etc. complete

(excluding cost of

reinforcement) with centering and shuttering/deshuttering etc. comp. up

to 6 meter height /depth Av. G.L.for all water retaining structures.RCC

14.1 RC.C. Top Slab 1.0 cu.m. 9444.95

14.2 RC.C. Base Slab 1.0 cu.m. 9444.95

Supplying cutting, bending, binding and placing in position steel as per

plan and design and as per ISS 2502 including cost of steel and binding

wire for reservoirs/structures only including lift up to 6 meter height or

depth below G.L. for all diameters

Do – deformed (TMT) bars confirming to relevant IS Fe – 500 grade for all

Providing and applying Epoxy paint of approved make to concrete

surface for precast chamber including cleaning the surface by scrapping

and air blowers to the satisfaction of Engineer-in-charge necessary

scaffolding etc. complete with all leads and lifts and giving satisfactory

hydraulic test for water tightness as per IS codes

Ambaji Under Ground Drainage Under SJMMSVY

Rising main from SPS-01 to Gravity line of TSPS

Item Description Qty. Unit Rate in Rs.

17.00 RCC Precast MH Frame & Cover 1.0 No. 1121.00

RCC precast M.H. Frame & Cover Manufacture, supply & Delivery at store

or at site of work precast RCC M.200

Frame & cover suitable to drainage M.H. and as per type design &

Drawing including cost of reinforcement M.S.

Angles or Flat, curing mold work etc..

Heavy duty : Frame suitable for 50cm opening of MH

17.1 RCC Precast MH Frame & Cover 1.0 No. 1173.00

RCC precast M.H. Frame & Cover Manufacture, supply & Delivery at store

or at site of work precast RCC M.200

Frame & cover suitable to drainage M.H. and as per type design &

Drawing including cost of reinforcement M.S.

Angles or Flat, curing mold work etc..

Heavy duty : Cover suitable for 50cm opening of MH

18.00 Providing and fixing PVC steps 4.0 No. 87.00

Ambaji Under Ground Drainage Under SJMMSVY

Civil Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs.

Excavation for foundation with shoring & strutting if required as per

required gradient and line including all safety provision using site rails and

stacking excavated stuff including up to all required lead cleaning the site

etc. complete for all lift and strata as specified.

I) In all sort of soils and soft murrum

1.1 II)In hard murrum, boulders incl. macadam road. 66.00 cu.m. 155.25

1.2 III) In soft rock and/or masonry in CM or L M or Lime Concrete. 66.00 cu.m. 187.45

1.3 IV) In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking, 98.00 cu.m. 427.80

chiseling, or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking, chiseling,

or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking, chiseling,

or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking, chiseling,

or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking, chiseling,

or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking, chiseling,

or by chiseling/breaking only.

2 Refilling the pipeline trenches incl. ramming, watering, consolidating 163.00 cu.m. 25.30

desposal of surplus stuff as directed within a radius of 3 km..Refilling as

Refilling the pipeline trenches incl. ramming, watering, consolidating

desposal of surplus stuff as directed within a radius of 3 km.--do-- with

selected soil brought from outside including all lead

Anchor bars below RCC raft slab including drilling of necessary size hole in

dry or wet condition, grouting with hilti OR EQUILVANT in dry or wet

condition, including random pull out test for 5% of total bars anchored as

per drawing and instruction of engineer-in-charge, (excluding cost of TMT

Bars) (In Hard Rocky Strata)

5 Providing and casting in situ C.C. in grade M-15 (approx. corresp. to prop. 30.00 cu.m. 5641.90

1:2:4) (proportions as per mix design or as per Table 9 of IS456 2000 in

masses by weigh batching ) using granite, quartzite trap metal of size 6 mm

to 20 mm for RCC work, including scaffolding centering, form work,

needle vibrated consolidation, curing comp. up to 6 meter depth or height

(excluding cost of reinforcement and neat finishing) with centering and

shuttering/deshuttering etc. comp. for structure for other than water

retaining. Footing (With form work)

Ambaji Under Ground Drainage Under SJMMSVY

Civil Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs.

6 Providing and casting in situ C.C. in grade M-15 (approx. corresp. to prop. 50.00 cu.m. 5441.80

1:2:4) (proportions as per mix design or as per Table 9 of IS456 2000 in

masses by weigh batching ) using granite, quartzite trap metal of size 6 mm

to 20 mm for RCC work, including scaffolding centering, form work,

needle vibrated consolidation, curing comp. up to 6 meter depth or height

(excluding cost of reinforcement and neat finishing) with centering and

shuttering/deshuttering etc. comp. for structure for other than water

retaining. Footing (Without form work)

7 Providing and cast in situ C.C. in grade M-30 proportions of ingredients as 60.00 cu.m. 9444.95

per mix design by weigh batching using granite, quartzite trap metal of size

12 mm to 20 mm and or 6 mm to 12 mm including scaffolding centering

formwork, needle vibrated consolidation, curing and hydraulic testing etc.

complete (excluding cost of reinforcement) with centering and

shuttering/deshuttering etc. camp. up to 6 meter height /depth Av. G.L.for

all water retaining structures.

R.C.C. base slab

7.2 R.C.C. staircase 1.00 cu.m. 9654.25

7.3 R.C.C Beams 10.00 cu.m. 9758.90

7.4 R.C.C. Top slab & Platform 10.00 cu.m. 9444.95

8 Providing and cast in situ C.C. in grade M-25 proportions of ingredients as 20.00 cu.m. 9599.05

per mix design by weigh batching using granite, quartzite trap metal of size

12 mm to 20 mm and or 6 mm to 12 mm including scaffolding centering

formwork, needle vibrated consolidation, curing and hydraulic testing etc.

complete (excluding cost of reinforcement) with centering and

shuttering/deshuttering etc. camp. up to 6 meter height /depth Av. G.L.for

all water retaining structures.

a) R.C.C. beams, lintels and bracket for gantry or chain pully blocks, plinth

beams, tie beams.

8.1 b) R.C.C. slabs and platform 10.00 cu.m. 9288.55

8.2 c) R.C.C. weather shed, pardi & staircase 10.00 cu.m. 9288.55

8.3 d) R.C.C. columns 10.00 cu.m. 10574.25

8.4 e) R.C.C. footing 3.00 cu.m. 9288.55

Supplying cutting, bending, binding and placing in position steel as per plan

and design and as per ISS 2502 including cost of steel and binding wire for

reservoirs/structures only including lift up to 6 meter height or depth

below G.L. for all diameters. Do-deformed (TMT) bars confirming to

relevant IS Fe-500 grade for all diameters.

Grouting with 1:3 cement mortar for anchor bolt pockets machine bases,

pipe sleeves, pocket holes etc. including roughening and cleaning of

concrete surfaces curing etc. complete.

Providing 20 mm thick Cement plaster in Cement mortar (1:2) using water

proofing compound of approved quality including finising etc . Complete

Ambaji Under Ground Drainage Under SJMMSVY

Civil Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs.

Providing and applying 20 mm thick sand faced cement plaster at outside

RCC / brick on work upto height 10 mtr. above ground level consisting of

12 mm thick backing coat of C. M. 1:3 (1 cement : 3 sand) and 8 mm thick

finishing coat of C. M. 1:1 (1 cement : 1 sand) etc. complete.

'Providing and applying 15 mm thick cement plaster in single coat on brick

work with floating coat of net cement slurry for interior plastering of

pumphouse and outside plastering of sump upto finished even and smooth

in Cement motar 1 : 3 (1 cement : 3 sand) including racking out joint curing,

scaffolding required if any, with necessary cement finishing etc. complete

Providing and applying 10 mm thick cement plaster in single coat on

concrete work for interior plastering upto floor two level finished even and

smooth in Cement mortar 1 : 3 (1 cement : 3 sand) in a single coat over

RCC slab (on ceiling) etc. complete as directed.

Providing and laying 40 mm thick heavy duty cement concrete flooring in

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal

size) with water proofing compound and ironite powder including finishing

with a floating of neat cement etc. complete laid in one layer in wet well

area below GL, and for platform of pumphouse 40 mm thick

Providing and applying epoxy paint of approved make to concrete surface

for RCC structure including cleaning the surface by scrapping and air

blowers to the satisfaction of Engineer-in -charge necessary scaffolding etc.

complete with all leads and lifts and giving satisfactory hydraulic test for

water tightness as per IS codes. For new surface-Two coats

Wall painting (two coats) with plastic emulsion paint of approved brand

and manufacture of undercoated wall surface to give an even shade

including thoroughly brushing the surface free from mortar dropings and

other foreign matter and sand papered smooth.

Distempering in 3 coats with oil bound distemper of approved brand and

manufacture and of required shade on wall surface to give an even shade

over and including a primer coat with distemper primer of approved brand,

thoroughly brushing the surface free from mortar dropping and other

foreign material and also inclusive of preparing the surface even and

smooth etc. complete, as directed on interior wall surface for pumphouse.

Ambaji Under Ground Drainage Under SJMMSVY

Civil Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs.

19 Providing & fixing in position aluminum fully paneled doors with 15 micron 3.00 smt 3024.00

natural matt brush finish anodized as per over all size shown on the

drawings and aluminum sections of approved make conforming to IS:733

and IS : 1285, made out of 102 mm x 45 mm x 1.90 mm thick aluminum

outer frame section weighing 1.640Kg/m. and shutter sections with bottom

/ lock rail 96 mm x 45 mm x 2.7 mm, top rail 48 mm x 45 mm x 2.70 mm

weighing 1.38 Kg/m. vertical styles 48 mm x 45 mm x 1.90 mm weighing

0.976 Kg/m. with rounded sides, fixed with roll plugs and screws or with

fixing clips, or with expansion hold esters including necessary filling up of

gaps at junctions, at top, bottom and sides with required PVC/neoprene

felt etc. and aluminum snap beading for glazing / paneling, C. P.

brass/stainless steel screws, including standard anodized aluminum fittings

and fixtures of approved make and of adequate size and in adequate

numbers, double action floor springs of approved make for each shutter

with standard pivot panels of 12 mm thick pre-laminated three layer

medium density, exterior grade particle board (termite proof, water proof

and fire proof)Grade 1, Type II conforming to IS : 12823 bounded with

phenol formaldehyde synthetic resin, of approved make including cost and

fixing of fixtures etc. complete as per detailed drawings with all lead and

20 Providing and fixing window having extruded aluminum Colour anodized 9.00 smt 1583.95

section frame main outer size 95mm x 24mm x 1.17mm @ wt.of

Kg/mt , horizontal Three track member size 92mm x 31.75mm x

1.30mm,@ Wt.1.07 Kg/mt , vertical member of size 92mm x 31.75mm x

1.50mm @ Wt. 1.06 Kg/mt with sliding shutters of horizontal member size

40 mmx18mm x1.29mm @ wt.of 0.456 Kg/mt, vertical member of size

40mm x 18mm x 1.29 mm @ wt.of 0.456Kg/mt/ with 5 mm thick

transparent bronze colour tinted float glass with powder coated aluminum

fittings and fixtures and transparent silicon sealant glass fixing to frame as

per details etc.

21 Providing and fixing M.S. grills of required pattern to wooden frames of 80.00 Kg 106.23

windows etc. with M.S. flats at required spacings and frame alround,

square or round bars with round headed bolts and nuts or by screws (A)

22 Providing and fixing standared extruded of alluminium section of size 5.00 smt 1175.56

63mm x 38.10mm x 1.2mm @ Wt. 0.643 Kg/mt with colour anodized

alluminium frame for ventilation with 5 mm thick frosted glass as details

etc complete for Ventilation

Providing and fixing rolling shutters of approved make made of 80 mm

wide M.S. laths inter-locked together through their entire length and

jointed together at the ends by end locks mounted on specially designed

pipe shaft with bracket plates, guide channels and arragements for inside

and outside locking with push-pull operation including the cost of hood

cover and spring etc. complete.(A) Shutters having width below 3.5 M.

Ambaji Under Ground Drainage Under SJMMSVY

Civil Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs.

Providing & fixing 50 cm wide MS ladder (without safety cage) fabricated

from MS flats 10 mm x 75 mm with 20 mm dia steel bar steps in double

rows @ 30 cm C/C. The include stays of 10 mm x 50 mm flats fixed at 3 mt.

C/C with welding anchoring and 3 coats anticorrsive paint.

25 Saftey cage for MS ladder 500.00 Kg 77.05

Providing Cement vata (10 cm x 10 cm size) quarter round in cement

mortar 1:1 including neat cement finishing, watering etc. complete.

27 Providing 100 mm x 100 mm size vata in cement concrete (1:2:4) including 68.00 Rmt 41.00

water proofing compounds, smooth finish, curing, etc. complete for the

internal side of the sump.

28 'Providing and fixing water tight construction or expansion joints 150 mm. 370.00 Rmt. 379.50

dia. Wide thin ribbed PVC.

Brick masonry in cement mortar (1:5) using common burnt clay building

bricks having crushing strength not less than 35kg/cm2 including

scaffolding,curing, etc. complete for walls, parapets, etc. at all levels.Extra

for brick work in superstructure above plinth level upto floor two level

Brick work using common burnt clay building bricks having crushing

strength not less than 35kg / Sq. C. M. in ramp, steps and Foundation &

Plinth in cement morter1:5 (1 cement : 5 coarse sand) including racking out

joints, curing, scaffolding required if any etc. complete, as directed.

Half brick masonary in common burnt clay building bricks having crushing

strength not less than 35 Kg./sq.cm. in cement mortar (1:4).

32 Providing and fixing 40mm dia. GI pipe medium weight (3.17 kg/rmt 40.00 Rmt. 1784.00

approx ) quality as railing with angle iron support at 1.5 m c/c using 75 x

x 10 mm angles, 1.15 m long with three rows of pipes as railing including

necessary painting with two coats of approved quality oil paint over one

coat of approved primer including necessary welding, bolting required, if

33 Providing and fixing MS grating with 8 mm thick 50 mm wide flat at 50 mm 20.00 smt 12590.00

c/c to form grid pattern as specified and wherever directed including two

coats of approved quality oil paint with one coat of primer red oxide etc.

Supplying, cleaning, cutting, bending, welding, fabricating, erecting

structural steel in position irrespective of locations and levels as per

drawing including handling and transport etc. complete including applying

two coats of primer red oxide and 'two coats of approved quality of paint

over it etc. complete as directed for gentry girder, platform, 'stairs,

chequered plate for cable trench etc.

Providing and laying broken chine mosaic flooring for terrace using 12 mm

to 20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to

plain or slope and to be tempered to bring mortar creme out upto surface

using white cement including rounding off junctions and extending them

upto 15 cm along the wall,clearing with water and oxalic acid etc. as

Ambaji Under Ground Drainage Under SJMMSVY

Civil Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs.

Providing and fixing plastic moulded reinforced steps with 10 mm TOR

steel bar with plastic 'polyproclene (P.P.) material (vergin) etc. complete.

37 Providing, laying and jointing in true line and level 110 diametre U.P.V.C 30.00 Rmt. 1053.73

(Type B) conforming to IS 13592-1992 with one end plain and other end

socketed with rubber ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with

each other with rubber lubricant, pipe shall be fixed on wall using of PVC

clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at

every 2000 mm center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent cement including cost of

all materials..

Providing and fixing 1.20 Metre high fencing with 2.0 Metre long M.S.

Angle posts 40mm x 40 mm x6 mm and oil painting 3 coats fixed at

Mt,C/c. with five Horizontan lines and two diagonals of galvanised steel

barbed wire weighting 9.38 Kg. per 100 Metre, strained and fixed to posts

with G.I,staples including fixing the postsin ground with 0.5 M x 0.5.M x

M. block in C.C1:5:10 etc complete.

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

1 (A) MECHANICAL WORKS 2 Set 6,67,927

NON-CLOG SEWAGE SUBMERSIBLE PUMP MOTOR SET:

Supply, Installation, Testing and Commissioning (SITC) of Non-clog submersible

pump of following duty parameters along with LV AC submersible induction

motor air filled dry type pump-motor set shall be of materials of construction

and must have all required accessories viz. automatic coupling device, double

guide pipes, chain with shackles, Submersible Power & control cable (copper

flexible & stranded type conductor of reqd. cores & size for each pump motor

set) & length of 15 m long each run with necessary electrical termination

connection at junction box / starter panels, RCC foundation with duck foot bend

for auto coupling & delivery bend and PMU etc. as per equipment data sheet

and detailed technical specifications and also including in scope any other parts /

accessories / fittings required to complete the work in all respects & satisfactory

operation of pump set.

Pump Capacity (Type-1): 110 m /hr, (1W+1S)

Max. RPM: 1500 &

Motor Rating: Minimum 30 kW (or higher as recommended by pump

Over all Minimum Acceptable Efficiency at Duty Point: 48.5%.

2 --- Item description as above --- 2 Set 4,84,957

Pump Capacity (Type-2): 60 m3/hr, (1W+1S)

Max. RPM: 1500 &

Motor Rating: Minimum 22 kW (or higher as recommended by pump

Over all Minimum Acceptable Efficiency at Duty Point: 40.00%.

3 VALVES: 2 Nos. 6,433

SITC of CI / DI Double Flanged, Manually Operated Sluice Valve confirming to IS

14846, PN 1.0 of following sizes with SS 304 seat rings and SS spindle with hot

dipped galvanised hardwares, bolts, nuts & washers etc. as per IS and

Specification & complete the work in all respects.

Size: 150 mm NB (on delivery of each pumpsets type-1)

4 --- Item description as above --- 2 Nos. 4,002

Size: 100 mm NB (on delivery of each pumpsets type-2)

5 --- Item description as above --- 1 No. 10,555

Size : 200 mm NB (on common header)

6 SITC of Non slam, flanged, CI/DI Single Door type Non Return Valve conforming 2 Nos. 8,612

to IS 5312 (Part-1), PN 1.0, having DI/CI body and door, CF8M seat rings

alongwith all necessary hardwares as per specifications and complete in all

Size: 150 mm NB (on delivery of each pumpsets type-1)

7 --- Item description as above --- 2 Nos. 5,787

Size: 100 mm NB (on delivery of each pumpsets type-2)

8 SITC of approved make CI/DI Flanged Air Valve with Isolation Sluice Valve as per 1 No. 11,600

AWWA / IS 14845 PN-1.0 & IS-14846 PN-1.0 respectively with SS304 float, gun

metal nozzle, complete hardware's, bolts, nuts & washers, gaskets etc. complete

as per IS and Specification.

Size: 50 mm NB (On header)

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

9 SITC of Flange ends Expansion Bellow (PN 1.0) as per EJMA standards and as per 1 Nos. 6,216

specs. and complete in all respect.

Size : 200 mm NB X 300 mm L (on Common Header)

10 DI PIPES 1150 kg 155.00

SITC of double flanged DI Pipes confirming to IS 8329-2000, class K9 with

connections complete for delivery and header lines and as per specifications.

The scope also includes connection with main header/rising main & complete

the work in all respects.

Size: 80 mm dia. to 300mm dia.

11 DI FITTINGS 500 kg 155.00

Supply, installation, connection with delivery / header, testing and

commissioning of Flanged DI Fittings and Specials like 90 deg. Bend, Drilled /

Drilled Blind Flanges, Reducer / enlarger, Tee, etc. as required to complete the

piping and connection of pumps with header/rising main conforming to IS

& complete the work in all respects.

Size: 80 mm to 300 mm dia.

12 Flanged Joints of Pipes, Fittings and Specials: 8 Nos. 611

Supply, Installation, Making of Flanged DI /CI / GI / MS Pipes, Fittings and

Specials Joints with all jointing materials, rubber packing, nut bolts, labour

etc.for complete connection.

Size : 150 mm dia.

13 --- Item description as above --- 8 Nos. 477

Size : 100 mm dia.

14 --- Item description as above --- 15 Nos. 837

Size : 200 mm dia.

15 MONORAIL EOT WITH ELECTRIC CHAIN HOIST 1 Set 1,76,240

SITC of Electrically Operated Chain Hoist & Electrically operated Trolley, suitable

to operate on Mono Rail Girder having motorised motion in vertical lifting &

cross travel, manufactured as per IS:6547-1972-Class-II & IS-3177- Class-II,

complete with electrically operated chain hoist & Electically operated geared

trolley, brake, chain-gear, motors, safety device, pendant push button, starter

panel, cables from motor to starter panel and all other required accessories like

limit switches, panel, power supply system (Fastoon cable type), fasteners,

epoxy painting, etc. tested for over load as per IS complete as per specifications

and complete in all respect.

Capacity : Min. 1.0 Ton. (At Pump House)

Lift : 10.00 m as mini. or as per site req.

Bay Length : 7.5 m min. or as per site req.

(w/o MONORAIL GIRDER & MS supporting structure)

16 --- Item description as above --- 1 Set 1,76,240

Capacity : Min. 1.0 Ton. (Above Screen Chmber)

Lift : 8.00 m as mini. or as per site req.

Bay Length : 3.0 m min. or as per site req.

(w/o MONORAIL GIRDER & MS supporting structure)

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

17 SLUICE GATE 1 No. 1,64,640

SITC of Manually operated C.I. Sluice Gate conforming to AWWA C 501 or IS :

13349 - 1992 Class - 1 with rising spindle, single faced, wall thimble mounted,

handwheel, flange back frame, head stock, Spindle with supports brackets

having length as specified or to suit site condition, suitable for seating as well as

unseating water head, complete in all respect.

Gate Size : 450 mm X 450 mm - approx. 4.0 m spindle length (at inlet chamber) -

Conventional Bottom Closing or suitable Closing

18 --- Item description as above --- 4 Nos. 1,07,460

Gate Size : 200 mm X 200 mm - approx. 4.2 m spindle length (at each Screen

Inlet & Outlet) - Flush Bottom Closure type or suitable Closing.

19 SITC of Box Type Manual Mesh Screen having following size, made of SS 304 2 Set 1,20,450

material having round bars of size 9.0 mm dia with clear bar opening as specified

here below, suitably welded in outer frame of equal Leg SS angle of size 50 mm x

50 mm x 6 mm thick or higher, with intermediate support at required locations,

complete as per specs. & shall also including followings:

The screen shall be with SS perforated Screening Material Collection Box at

bottom end of Screen having size as specified, fabricated from 3 mm thk SS

sheet, screen shall be suitable to slide complete screen through rollers between

existing guide passage of MCP 400, embedded/ fixed in wall on both sides of

RCC wall up to top of chamber with all necessary hardware, SS nuts, bolts &

wahsers, sacrificial Brass lugs on sides, min. two lifting lugs/hooks & SS lifting

chain having intermediate link/chain of 100 mm dia. at every 1.5 m distance

with shackle, etc. complete in all respects and provided with 1 set of cleaning

rake with each screen, complete as per specification and complete in all respect.

Screen Size: 900 mm (W-or actual chamber width as per site ) x 800 mm (H) x

Box Size: 900 mm (W-or actual screen width) x 100 mm (H) x 300 mm (D)

Opening: 50 mm x 50 mm sq. opening

Note : Screen suitable for 900 mm wide screen chamber or to suit site

(w/o Guide channel & MS supporting structure)

20 Providing, Supply of Structure Steel at site of work with freight, loading, 2000 kg. 64.838

unloading carting, etc. including all taxes and duties complete such as joints,

channels, angles, Iron Rails, ISA/ISMC/ISMB/MS flat, Plates, Chequered plates

(min. 7 mm thickness) for cable trench etc. required for support structure of all

Electro-mechanical equipment, piping, etc. for support on floor / wall / beam /

brackets etc. as per tender and IS.

21 Labour Charges for lowering, laying, Fixing with fabrication various size section 2000 kg. 11.365

of MS such as joints, channels, angles, Iron Rails, ISA/ISMC/ISMB/MS flat, Plates,

Chequered plates, for cable trench etc Complete with two coats of red oxide and

two coats of approved colour shade of epoxy paint as per relevant IS and as per

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

22 (B) ELECTRICAL WORK 1 Set 39,391.46

TPN MCCB (For LT Service Obtaining Requirement)

SITC of 250A TPN microprocessor MCCB, LSIG (50kA) with inbuilt O/L, S/C & E/F

protection with Extended rotary handle, Terminal spreader, Auxiliary change

over & Trip contact, with Outdoor Enclosure with canopy 2mm thick

Single/double door & Wall mounted/ stand mounted as per site requirement

(with incoming & outgoing cable entry at bottom )with Cable end boxes with

RYB indicating lamp, Digital voltmeter, VSS,ON,OFF & Trip indicating lamp etc as

per Power supply company requirements & location. Including all civil works for

fixing of panel on wall.

(Wall mounted at Location as per PSC req.)

23 MEDIUM VOLTAGE PANEL BOARD (PMCC /APFC) 1 Set 9,78,000.00

SITC of PMCC Panel (50kA), compartmentalized, Stand mounted as per site

condition and requirement with required modification / rectofication works as

required, operating height maximum 1800/1900 mm, Extensible on both ends,

suitable for Manual & Auto operation -Local & through PLC/SCADA operation as

per site conditions complete in all respects as per Tender SLD / Specification / IS

and including following as minimum:

(1) One no. Incoming feeder FP 250A Microprocessor MCCB (50kA), LSIG, with

inbuilt O/C, S/C, & E/F protection for I/c with Digital Voltmeter, Voltmeter

selector switch, Digital Ammeter, Ammeter selector switch, Power Factor Meter,

MFM with RS-485 of Class-0.5, Indicating lamps R,Y,B,On,off,Trip, 3nos.

250A/5A, Cl.-0.5 metering CT, CL 0.5 CT for APFC relay etc. Constant

voltage/control voltage transformer 1500VA, 415V/230V AC, with tapping +/-5%

in steps of 2.5%, 32A DP MCB complete in all respects.

(2) 250A TPN Main Aluminium busbars. (main busbars size with current density

(3) 22 KW STAR -DELTA STARTER FEEDER (SUBM.): 2 NOS :

22 KW or higher as per pump manufacturer recommendation Star-delta starter

with 100A TPN Thermal magnetic MCCB with Adjustable O/L & Adjustable S/C

protection, 95A AC3 duty contactors (3 nos.), O/L Relay, star-delta timer,

Ammeter with ASS, Resin Cast CT Cl: 0.5(3 nos.),SPP,PMU, A/M, L/R switch, ON,

OFF, TRIP Indication & Start, E-Stop & Reset pushbutton etc. for S/D starter.

complete in all respects.

(4) 30 KW STAR -DELTA STARTER FEEDER (SUBM.): 2 NOS :

30 KW or higher as per pump manufacturer recommendation Star-delta starter

with 125A TPN Thermal magnetic MCCB with Adjustable O/L & Adjustable S/C

protection, 95A AC3 duty contactors (3 Nos), O/L Relay, star-delta timer, MFM

with RS-485, Resin Cast CT Cl: 0.5, MPR with RS-485, CBCT, SPP, PMU, A/M, L/R

switch, ON, OFF, TRIP Indication & Start, E-Stop & Reset pushbutton etc. for S/D

starter. complete in all respects.

(5) 63A TPN TM MCCB FEEDER : 2 No. (2 nos. Spare)

SITC of comprising

Lighting of 63A

Distribution TPN Thermal

Board (LDB) as Magnetic

under: (TM) MCCB, with 2 Nos. 7,947.39

SITC of 3 Phase 4 Wire 4P, double door Prewired LDB each for Indoor Lighting &

Outdoor Lighting Suitable to house :

Incoming: 32A FP, ELMCB (30mA)

Outgoing: 20A SP MCB (9 nos.) & 16A SP MCB (9 nos.)

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

25 LOW VOLTAGE (LT) CABLES 30 Mtr. 783.00

Supply, laying, testing and commissioning of 1.1 kV, A2XFY(X)/2XWY(X) XLPE

insulated (IS 7098) AL / Cu stranded conductor, Extruded innersheath cables as

per specification & IS.

The cable when laid outside the building shall be laid underground in trench

with brick & sand protection/in DWC pipes as per specified method and shall be

laid in prepared trench/ on cable tray when laid inside the building.

SITC of 3.5C x 240 sq. mm. A2XFY(X) Cable (1 run for MCCB to PMCC panel)

26 SITC of 4C x 6 sq. mm. A2XFY(X) Cable (For Indoor LDB, 1 no. Outdoor LDB) 50 Mtr. 130.44

27 SITC of 4C x 2.5 sq. mm. 2XWY/2XFY(X) Cable (1 no. for EOT with ECH at Pump 200 Mtr. 283.15

House, 1 no. for EOT with ECH at manual screen, 1 no. for ICP/PLC Panel & for

nos. street light)

28 SITC of Single core 95sq. mm. PVC insulated circular unsheathed copper 20 Mtr 919.45

conductor flexible Cable (For Power supply Metering Panel to I/c MCCB Unit)

29 CABLE END TERMINATION AND CONNECTION: 2 Nos. 838.00

SITC of Double compression Ni-Plated brass cable glands and crimping type

Bimetallic lugs / sockets with necessary tools and equipments as specified in

specifications and IS. The glands and lugs / sockets shall be suitable for cable

size and type mentioned below & as per specifications.

1) Earthing the glands and armouring with earthing clamp and jumper and also

connecting to common earth bar.

2) The job also includes, if necessary, supply & fixing of extension busbar of same

material on MCCB or panel board terminal / connector to connect more than

one no. of parallel cables or to connect higher size cable to lower size unit. The

job also includes earthing the glands and armour of the cable with common

earth bar or flexible copper mesh.(Cable termination qty. shall be as per site

SITC of 3.5C x 240 sq. mm. A2XFY(X) Cable (1 run for MCCB to PMCC panel)

30 Same as above but, 4C x 6 sq. mm. A2XFY(X) Cable (For Indoor LDB, 1 no. 4 Nos. 111.00

31 Same as above but, 4C x 2.5 sq. mm. 2XWY/2XFY(X) Cable (1 no. for EOT with 14 Nos. 68.93

ECH at Pump House, 1 no. for EOT with ECH at manual screen, 1 no. for ICP/PLC

Panel & for 4 nos. street light)

32 Single core 95sq. mm. PVC insulated circular unsheathed copper conductor 10 Nos. 49.84

flexible Cable (For Power supply Metering Panel to I/c MCCB Unit)

33 CABLE TRAY 70 Mtr. 584.34

SITC of G.I. (hot dip galvanised )Ladder type medium duty (2mm thick) Cable

Tray with necessary bends, tees, reducers, covers and clamps for fixing. All

material shall be Hot dip galvanised as per Specification. And including all

300 x 100 mm - Ladder type

34 150 x 50 mm - Ladder type 120 Mtr. 292.70

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

35 Supply, laying and erection of 75 mm ID approved make Double Walled 50 Mtr. 158.00

Corrugated pipes (DWC) of polyethelene (confirming to IS-14930 II) with

necessary connecting accessoies of same material at required depth for laying of

cable below ground / road surface for enclosing cable and back filling the same

to make ground as per original. (LT cable etc)

36 Cable Trench, Laying & Installation of Cable: Making cable trench in soft soil of 50 Mtr. 48.78

suitable width of 90cms deep for laying cable, Sand cushioning and brick

protection on sides and on top all over the run and back filling the same and

making the surface as normal ground as per IS & Specification. (For laying of LT

cable in ground)

37 Cable Protection/ Covering in Trench: Cable Covering with second class bricks or 20 Mtr. 141.05

cement tiles laid cover the cable (top) & also on both side with sand

bedding/cusioning of 75mm.& covering of 150mm Layer of sand above cable

(16 bricks per meter.) as per IS & Tender Drg/ Specification. (For HT/LT cable

protection) complete in all respects as instructed by EIC.

38 CHEMICAL EARTHING SYSTEM 2 Set 11,123.58

SITC of Maintenance free chemical earthing (copper) with earthpit of minimum

bore size dia. 225mm Safe Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS-3043:1987 /Tech spec. made of corrosion free Pipes having Outer pipe

dia of 48 mm having 250 Micron copper plating, Inner corrosion free Hot dip

galvanised (80 to 100 micron) pipe dia of 26 mm with copper flat strip type

connection terminal 14mm dia with constant ohmic value surrounded by highly

conductive corrosion resistant chemical compound with high charge dissipation

suitable for electrical installation & of 3Mtr. length of Pipe with two nos. 25Kg.

bag of Back filling compound. (2nos. for ICP/PLC Earthing)

NOTE: Earthing Resistance value & date shall be painted on the chamber cover.

39 SITC of Maintenance free chemical earthing with earthpit of minimum bore size 6 Set 7,450.01

dia. 225mm Safe Earthing Electrode consisting Pipe-in-Pipe Technology as per IS-

3043:1987 /Tech spec. made of corrosion free Hot dip Galvanised (min

Microns) Pipes having Outer pipe dia of 76 mm , Inner corrosion free Hot dip

galvanised (80 to 100 micron) pipe dia of 26 mm with copper flat strip type

connection terminal 14mm dia with constant ohmic value surrounded by highly

conductive corrosion resistant chemical compound with high charge dissipation

suitable for electrical installation & 3Mtr. length of Pipe with two nos. 25Kg. bag

of Back filling compound. (2 nos. for LT panel & 4nos. for all elect. Equipments)

NOTE: Earthing Resistance value & date shall be painted on the chamber cover.

40 SITC of 50mm(w) x 8mm(T) etc. sizes as required, HOT dip galvanized GI Strip 575 Kg. 81.66

including supply & fixing using GI spacers, saddles when laid inside the building

and inclusive of excavation & refilling of earth when laid outside the building &

interconnection with earth pit & all electro-mechanical equipments.

(50X6 G.I Strip wt.2.3 kg/m, 2.3x250Mt.=575kg.)

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

41 Supply, laying and erection of 25mm(w) x 3mm(T) etc. sizes as required, HOT 120 Kg. 81.66

dip galvanized GI Strip including supply & fixing using GI spacers, saddles when

laid inside the building and inclusive of excavation & refilling of earth when laid

outside the building & interconnection with earth pit & all electro-mechanical

equipments. (25X3 G.I Strip, 0.6 Kg/m, 0.6x200Mt.=120Kg.)

42 Supply, laying and erection of 25mm(w) x 3mm(T) etc. sizes Copper Strip 38 Kg. 834.61

including supply & fixing of bolts, saddles when laid inside the building and

inclusive of excavation & refilling of earth when laid outside the building &

interconnection with earth pit & PLC Panel (25X3 Cu. Strip, 0.761 Kg/m, 0.761 x

Copper Bolt,Nuts ,Washers shall be used for Connecting Earth electrode to

individual eqp. Bitumen shall be used at the place of joint/welding. (For PLC

Panel to Earthing)

43 SITC of HOT Dip Galvanized iron strip wire 8 SWG (For LDB,LCS, etc.) 21 Kg. 81.66

(8 SWG G.I Strip, 0.103 Kg/m, 0.103 x 200Mt.=20.6 Kg.)

44 INTERNAL WIRING 80 Mtr. 82.72

SITC of Mains & outlet points wiring with 1.1 kV grade FRLS PVC insulated ISI

marked flexible stranded copper conductor wires with medium class min.

25mm. dia. Electrical grade PVC pipe and accessories to be erected concealed in

/ to be run on surface / wall / ceiling with following sizes as mentioned below.

The unit rate wirings shall be with connector, PVC junction box, wires, holder,

ceiling rose, angle holder, switch, sockets, switch board, brass chromium /

cadmium plated machine screws, phase and neutral wires, green Earth

continuity wires etc. as required to complete wiring from LDB panel to the final

outlet termination points. The wiring shall be as per IS:732, IS:4648 and as per

tender specification / IS.

(a) SITC of Mains wiring with 3 wire 1.5 sq.mm.

45 same as above, but (b) SITC of Mains wiring with 3 wire 2.5 sq.mm as per tender 100 Mtr. 101.81

specification & IS.

46 same as above, but (c) SITC of Mains wiring with 4 wire 1.5 sq.mm as per tender 100 Mtr. 91.20

specification & IS.

47 same as above, but (d) SITC of Mains wiring with 4 wire 2.5 sq.mm as per tender 120 Mtr. 126.20

specification & IS.

48 SITC of Point wiring for Light / fan / Bell / Primary Point with 2nos. 1.5 sq. mm & 19 Nos. 345.72

earth wire of 1.5 sq. mm (green) both are of ISI marked 1.1 kv grade FRLS PVC

insulated multistrand copper wires , pipe to be erected concealed in flushed on

wall / ceiling, complete with 6A Tissino Type ISI marked flush type switch / bell

push & accessories erected on metal / PVC Box covered with 3 mm thick PC

(Polycarbonate) / Acrylic sheet with necessary lamp holder / ceiling Rose / H. D.

connector as directed with medium class Rigid PVC pipe & accessories.

49 SITC of 6A independent Plug with 2nos. 1.5 sq.mm Cu. Mains size wiring & 2 Nos. 305.42

earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multistrand copper wires with medium class Rigid PVC pipe and

accessories to be erected on wall / ceiling, complete with ISI marked 3 / 5 Pin

socket and tissino type switch erected with earth continuity connection erected

on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / Acrylic sheet.

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

50 SITC of 6/16A independent Plug with 2nos. 4 sq.mm Cu. Mains size wiring & 2 Nos. 599.18

earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multistrand copper wires with medium class Rigid PVC pipe and

accessories to be erected on wall / ceiling, complete with ISI marked 3 / 5 Pin

socket and tissino type switch erected with earth continuity connection erected

on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / Acrylic sheet.

(2 nos. LT Room cum Pump House)

51 SITC of One 300/380 mm dia. Ex fan 16A independent Plug point near Ex. Fan 3 Nos. 599.18

with 2nos. 4 sq.mm Cu. Mains size wiring & earthwire of 1.5 sq.mm (green) both

are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires with

medium class Rigid PVC pipe and accessories to be erected on wall / ceiling,

complete with ISI marked 3Pin socket and tissino type switch erected with earth

continuity connection erected on Metal / PVC box covered with 3 mm thick

PC(Polycarbonet) / Acrylic sheet. Plug point shall be near Ex.Fan.

52 SITC of 300mm sweep 960 R.P.M exhaust fan, capacitor type, having double ball 1 Set 1,977.83

bearing, M.S.blades, mounting frame, forearms, suitable to operate on 230V,50

HZ AC supply conforming to IS: 2312.Fan shall be painted with epoxy grey colour

controlled by one 6 A flush type switch on board and 6A plug point near Ex. fan.

53 SITC of 380mm sweep 1400 R.P.M exhaust fan, capacitor type, having double 2 Nos. 3,236.65

ball bearing, M.S.blades, mounting frame, forearms, suitable to operate on

230V,50 HZ AC supply conforming to IS: 2312.Fan shall be painted with epoxy

grey colour controlled by one 6 A flush type switch on board and 6A plug point

54 SITC of Single Phase 20A 3 Pin Metal clad Industrial Type Socket with plug top 1 Nos. 820.00

and 20A SPMCB, suitable for flush mounting, in 16 SWG MS box of suitable size

and covered with 3 mm thick electrical grade hylam sheet or equivalent ISI

marked Electrical grade Bakelite sheet and earthing with 2.5 sq.mm insulated

copper wire run inside the conduit including interconnections etc. complete as

(1 no. LT Room)

55 SITC of Sheets steel powder coated weather proof enclosure with One no. 32A, 2 No. 811.28

415V 4P MCB for Motor & Inductive load (C Curve) having 10 KA breaking

capacity & confirms to IS: 8828. (1 no. for EOT with ECH at Pump House, 1 no.

for EOT with ECH at manual screen)

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

56 LED LIGHT FIXTURES & LIGHTING: 5 Nos. 310.73

SITC of Indoor wall mounting 20Watt or up to 25% higher wattage LED 4 feet

Tube Light indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled

on single MCPCB, with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA polyester powder coated and high U.V. &

corrosion resistance with diffuser and/or Polycarbonate optics with company

120 to 300 V,Power Factor more than 0.9, THD < 20 %,

CCT 4000 K to 6500K, Uniformity ratio >0.7,

Luminaries efficacy> 85 lumens/watt

LED driver efficiency > 85 %

(Each fitting required LM-79 & LM-80 Certificates)

Tube Light with integral / non-integral driver, Surge-4KV,IP-20, 4 feet, Cat-III

57 Item description as above SITC of 7 watts LED Lamps integral type,cool white 2 No. 117.72

with PC diffuser suitable for B22 LAMP holder (2 nos. LT Room cum Pump

58 1200mm sweep ceiling fan, capacitor type, having double ball bearing 450mm 2 Set 1,676.65

down rod, canopies, shackle, rubber bush, blades, electronic speed regulator,

suitable to operate on 230V,50Hz AC supply conforming to IS: 374/1979.Fan

shall be painted with white colour.(2 nos. LT Room)

59 SITC of 40W LED Surface / Wall mounted LED Flood Light fittings with High 4 Nos. 5,454.15

power White LEDs wattage of 1Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses with company

mark/name engraved or embossed

120 to 300 V,Power Factor more than 0.95, THD < 20 %, CCT 5000 K to 5700K,

Uniformity ratio >0.45, Luminaries efficacy> 85 lumens/watt . LED driver

efficiency > 85 %.

( Each fittings required LM-79 & LM-80 certificates)

(IP-65), Surge -4KV Cat-III

For Indoor use: (at Pump House)

60 SITC of 'B' class galvanised iron pipe 32 mm outside dia 45 cms long duly welded 9 Nos. 586.46

on 20 cms x 20 cms x 3 mm thick M.S. base plate, erected on wall or corner for

mounting luminaries with necessary hardware materials duly painted for wall

mounting indoor flood light fixtures on Wall of Buildings & post top lantern.

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

61 EXTERNAL LIGHTING (Flood LIGHT): 5 Nos. 6,392.69

SITC of 70W LED Wall mounted LED Flood Light fittings with High power White

LEDs wattage of 1Watt and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die cast aluminum housing with

smooth finish powder coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses with company mark/name engraved or

120 to 300 V,Power Factor more than 0.95, THD < 20 %, CCT 5000 K to 5700K,

Uniformity ratio >0.45, Luminaries efficacy> 85 lumens/watt . LED driver

efficiency > 85 %.

( Each fittings required LM-79 & LM-80 certificates)

(IP-65), Surge -4KV Cat-III

For Outdoor use: (for area lighting)

62 EXTERNAL LIGHTING (STREET LIGHT): 4 Nos. 11,223.27

SITC of Street Light Pole, steel tubular swaged type, 7.5 meter long with single

arm & M.S.base plate with pipe cap and over hung 1.5 m long having dia to suit

the socket of 240V LED street light fixtures. Street light pole unit rate shall be

with (i) IP 65 SMC box of size 20 x 15 x 15 cms. with MCB & terminal strip inside

the box with hinged/sliding door (ii) 50mm dia, B class GI pipe bracket

min.1.5mtr long for Incoming & outgoing cable (iii)MS Cable Clamp of 25 x 3mm

(iv)SITC of 1.5 Mtr.single Arm bracket of medium duty MS pipe of 4.2 cms. Out

side dia complete with suitable sleeve tubing 45 cms. long of required size of

pole top etc. and having spread of 1.5.mtr. length with 110 deg.(v) Complete

painted with one coat of Red oxide / PU base primer and two coats of

Aluminium / PU paint for Pole,Arm, pipe etc.

63 SITC of 70W LED Street light fittings with High power White LEDs wattage of 4 Nos. 6,274.98

1Watt and above assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminum housing with smooth finish

powder coated and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses with company mark/name engraved or embossed

120 to 300 V,Power Factor more than 0.95, THD < 20 %, CCT 5000 K to 5700K,

Uniformity ratio >0.45, Luminaries efficacy> 85 lumens/watt . LED driver

efficiency > 85%.

( Each fittings required LM-79 & LM-80 certificates)

Street Light (IP-65), Surge -4KV, 70 watt Cat-III

64 SITC of M-20 / 1:2:4 cement concrete foundation for Street light pole & 70 % 4 Nos. 1,357.44

PCC from bottom including excavation for the pole of size 60 x 60 x 120 cms.

Deep in below ground level with plinth of 45 cms x 45 cms(or 45 cms dia x

cms) high upper ground level with necessary curing and finishing in approved

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

65 SAFETY ACCESSORIES 1 Nos. 9,105.45

SITC of following safety accessories complete with necessary fixing brackets,

other accessories and tools etc. as required to complete the job.

Supply & Erecting carbon dioxide (CO2) fire extinguisher of 6.5kg capacity with

necessary clamps made from 50 x 6 mm M.S. Flat with nut & bolts grouted in

(1 nos. LT Room cum Pump House)

66 Supplying of standard first AID box with antiseptic cream, medicine for use on 1 Nos. 314.97

wounds due burn, crepe bandage, guage bandage, medicated ready to use

bandage (Band-aid) adhesive tape for medicinal user, scissors, antiseptic

solution (Savlon or similar) etc. (All above contents shall be of standard makes)

(1 nos. LT Room cum Pump House)

67 Supply & fixing of printed instruction (First Aid) Chart both in English and 1 Nos. 136.80

Gujarati and duly framed with front glasses, for treatment of person suffering

from electric shock. (1 nos. LT Room cum Pump House)

68 Supply and fixing of 20 W fluorescent lamp operated emergency light with 1 Nos. 2,670.00

maintenance free battery for 3 hours operation during mains power failure.

(1 nos. LT Room cum Pump House)

69 Supply and laying of Synthetic Insulating Mat of Class - A of min. thickness 7 Sq.mt 1,078.53

2mm as per IS:15652 and with good electrical insulation property for r.

1.1KV/3.3KV as per site requirement. (For LT Panel)

70 (C) INSTRUMENTATION WORK 4 NOS. 5,413.00

PRESSURE MEASURING SYSTEM

Supply, installation, testing & commissioning of Diaphragm Type pressure guage

having 150 mm dial with necessary fittings/accessories in SS

(manifold valve, nipples etc.) complete in all respects and as per specs.

Range : 0 - 6 Kg/cm2 (at each pump's delivery side )

71 LEVEL MEASURING SYSTEM 1 NO. 84,568

Supply, installation, testing and commissioning of Hydrostatic type Level

Transmitter with Local Indicator and 4-20 mA Retransmission output with

meter cable, Junction box, all mounting accessories, hardware, Fixing of 2.5"

size UPVC pipe in Sump for installation the Hydrostatic sensor, Clamp,etc.

complete in all respects with local and remote display at PLC/HMI, as per

specification and having following measurement ranges for Sewage application:

Meas. Range: upto 10 m (at Sump)

72 LARGE SIZE LED DISPALY FOR SUMP LEVEL TX. 1 NO. 20,160

Supply, installation, testing and commissioning LED diplay 8" size ( 320 mm H X

650 mm W X 50 mm D) with 4-20 mA Input at Wet Well to monitor the level of

Wet Well from distance , all required accessories, etc. complete in all respects

as per specification.

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

73 Supply, installation, testing and commissioning of Float type Level Switch along 1 NO. 12,802.00

with 10 mtr. Cable and WP Junction Box (at wet well for dry run protection of

pumps ) complete in all respects and as per specification.The scope also

includes providing 4" flanged , puddle pipe approximate 300 mm long including

fixing of the same in civil structure slabe of pump house for mounting of level

switch.The work also include all necessary work like make hole,repair /

modification in slab, etc.

74 FLOW MEASURING SYSTEM 1 NO. 1,06,049.00

Supply, installation, testing and commissioning of remote type Full Bore

Electromagnetic Flow Meter comprising of IP-68 Sensor, IP66 remote

transmitter with 20 m cable between sensor and transmitter along with all

mounting accessories, hardware, etc. complete in all respect and as per specs

and shall have following size and measurement range. The scope also includes

necessary connection with header pipe.

Meter Size : 200 mm NB

Pipe size: 200 mm NB

75 PLC BASED CONTROL PANEL FOR SPS 1 LOT 7,30,296.00

Supply, Installation, Testing & Commissioning of PLC Based Instrument control

Panel with panel mounted 10 " colour touch screen HMI, 4G or Latest GPRS

modem with (Ethernet port + SIM Slot) for Remote data transmission to central

SCADA of client in future , Communication port for MFM. Instrument Control

Panel '(PLC Enclosure / Panel ) with necessary PLC based logic and wiring , Min.

1 kVA Online UPS + CVT (with 60 min min backup ), etc. complete in all respects

and as per specs with PLC having minimum I/O count of 20DI / 12 DO / 4AI

/2AO. These are the minimum IO requirement if any other IO,s required to

complete the work contractor shall be provide the same without any extra cost.

76 INSTRUMENT CABLE & ACCESSORIES 50 MTR. 146.00

Supply, Laying, Installation, Connection, Termination, Testing & Commissioning

of Instrument Cables, along with cable glands, lugs, cable trays, required

junction boxes, fittings and accessores as per specs. The unit rate shall include.

(a) Supply, loading & unloading of the cable at site from store.

(b) Shifitng of cable from site store to place of installation.

(c) Fixing of cable clamps, brackets, supports, route markers etc. where ever

required to fix the cables safely.

(d) Excavation, back filling and levelling of ground alongwith laying of fine sand,

protection bricks and other necessary civil material for laying cables outside the

(f)Testing and submission of sketches & reports of all the cables laid.

77 CONTROL CABLE 80 MTR. 330.00

78 SIGNAL CABLE 100 MTR. 133.00

Ambaji Under Ground Drainage Under SJMMSVY

Electro-Mechanical and Instrumentation Work of Construction of Sewage Pumping station (SPS-02)

Item Description Qty. Unit Rate in Rs. Amount in Rs.

79 INSTRUMENT CABLE TRAY 10 MTR. 476.00

G.I. Perorated type cable tray shall be made out of galvanized mild steel sheets

of 2 mm thickness with required asccessories . All material shall be Hot dip

galvanised as per IS 2629 (as mentioned in specification and tray hardware shall

200 X 25 mm - Perforated type

80 50 X 25 mm - Perforated type 15 MTR. 291.00

81 CABLE END TERMINATION AND CONNECTION : 4 NOS. 160.00

Supply, fixing, connection, testing and commissioning of double compression

brass cable glands and crimping type Bimetalic lugs / sockets with necessary

tools and equipments as specified in specifications and IS complete in all

respects. The glands and lugs / sockets shall be suitable for cable size and type

mentioned above. The job also includes earthing the glands and armour of the

cable with common earth bar or flexible copper mesh as applicable.

82 CONTROL CABLE 8 NOS. 230.00

83 SIGNAL CABLE 6 NOS. 160.00

Ambaji Under Ground Drainage Under SJMMSVY

Rising main from SPS-02 to Gravity line of TSPS

Item Description Qty. Unit Rate in Rs.

Excavation for trenches with shoring & strutting if required as per required

gradient and line including all safety provision using site rails and stacking

excavated stuff including up to all required lead cleaning the site etc.

complete for all lift and strata as specified.

I) In all sort of soils and soft murrum

1.1 II)In hard murrum, boulders incl. macadam road. 279 cu.m. 155.25

1.2 III) In soft rock and/or masonry in CM or L M or Lime Concrete. 279 cu.m. 187.45

1.3 IV) In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking, 416 cu.m. 427.80

chiseling, or by chiseling/breaking only.

Providing bedding incl. ramming, watering, levelling, consolidating etc.

complete as per standard and instruction of engineer incharge.

(II) As above with Murrum brought from outside including all lead

Providing and supplying D. I. K-9 grade pipes for following nominal bore 1100 Rmt

diameter with internal cement mortar lining including all taxes, insurance,

transportation, freight charges, octroi, inspection charges, loading,

unloading, conveyance to departmental stores, stacking etc. complete. (IS

8329-2000). For sewerage project cement mortor lining shall be with

sulphate resistance cement.

250 mm dia DI K-9 with EPDM Gasket

4 Lowering, laying and jointing C. I. S & S Spun pipes suitable for Tyton joints 1100 Rmt 146.05

/ Mortar lined D. I. Pipes of various classes with CI / MS specials of

following diameters in proper position, grade and alignment as directed by

Engineer-in-charge including

hydraulic testing etc. complete.

250 mm dia DI K-9 with EPDM Gasket

Manufacture, Supply & Delivery of Ductile Iron Flange socket spigot bends, 1337 kg

tees, reducers or any other specials as per BS-EN-545/1995 Class-A series

K12 suitable for use with D.I. Pipes manufactured as per IS:8329/1994

delivery of specials is to be made to GWSSB store or site of works any

where in Gujarat including all taxes, loading, unloading, carting, stacking,

insurance, inspection charges, octroi etc. complete.

Socket & Spigot Type 80 to 300 mm dia

Providing, supplying, Delivery and fixing of Water Hammer Control

Devices for use on various pumping main of following class and diameter

including all taxes, insurance, transportation, freight charges, octroi,

inspection charges. loading, unloading, conveyance to departmental

stores, stacking etc. complete. a) 250 mm dia Zero Velocity Valve with

bypass arrangement with CI Body (Class-15)

6.1 200 mm dia Air Cushion Valve with Cast iron body (Class-15) 1.0 No. 126945.00

Ambaji Under Ground Drainage Under SJMMSVY

Rising main from SPS-02 to Gravity line of TSPS

Item Description Qty. Unit Rate in Rs.

7 Providing, supplying ISI mark Cast Iron D/F Sluice Valves of following class 1 No. 15920.00

and diameter including all taxes, insurance, transportation, fright charges,

Octroi Inspection charges, loading, unloading, conveyance to site stacking,

PN-1 with hand wheel /cap operated (PD Type short body)

8 Lowering, laying & jointing in position following C. I. / D/F Sluice Valves 1 No. 1087.90

including cost of all labour, jointing material, including nut bolts & giving

satisfactory hydraulic testing, etc. complete.

PN-1 with hand wheel /cap operated (PD Type short body)

9 Providing, supplying,& fixing CI Tamper proof Air valves with SS 304 Float 3 No. 13789.00

gun metal nozzle of approved make & quality of following class and

diameter including all taxes, transportation, freight charges, octroi,

inspection charges, loading, unloading, conveyance to the departmental

stores, stacking etc. complete.

With Isolating Sluice Valve PN

10 Lowering, laying & jointing in position following air Valves including cost of 3 No. 472.65

all labour, jointing material, including nut bolts & giving satisfactory

hydraulic testing, etc. complete.

With Isolating Sluice Valve PN

11 Construction of Valve chambers in brick masonary, locally available in C.M. 6 No. 13053.65

1:6, foundation concrete 150 mm thick in C.C. 1:4:8 of trap metal size

mm to 40 mm thick, inside cement plaster in C.M. 1:3 and cement pointing

outside in C. M. 1 :3 & top cover of precast RCC slab 150 mm thick upto

mt. depth from G.L. but excl. cost of excavation and refilling. With cast in

situ RCC slab in two piece, with 23 mm thick brick masonary wall in

C.M.1:6, With precast slab in two parts 15 mm.

Size of chamber 1.3m x 1.3 m and 1.0 mt. deep.

11.1 for 1 m. extra depth 3 Rmt. 6996.60

12 Providing and casting in situ C.C. in grade M-15 (approx. corresp. to prop. 5 cu.m. 5441.80

1:2:4) (proportions as per mix design or as per Table 9 of IS456 2000 in

masses by weigh batching ) using granite, quartzite trap metal of size 6 mm

to 20 mm for RCC work, including scaffolding centering, form work,

needle vibrated consolidation, curing comp. (excluding cost of

reinforcement and neat finishing) with centering and

shuttering/deshuttering etc. comp. for structure for other than water

Footing (without form work)

13 Providing and casting in situ C.C. in grade M-20 (proportions as per mix 245 cu.m. 6348.00

design or as per table 9 of IS 456 2000 in masses by weigh batching ) using

granite, quartzite trap metal of size 6 mm to 20 mm for RCC work,

including scaffolding centering, formwork, needle vibrated consolidation,

curing complete (excluding cost of reinforcement and neat finishing) with

centering and shuttering/deshuttering etc. complete for structure other

than water retaining (Below G.L)

RCC ( For Thrust block & encasing)

Ambaji Under Ground Drainage Under SJMMSVY

Rising main from SPS-02 to Gravity line of TSPS

Item Description Qty. Unit Rate in Rs.

14 Supplying cutting, bending, binding and placing in position steel as per plan 0.5 MT 77285.20

and design and as per ISS 2502 including cost of steel and binding wire for

reservoirs/structures only including lift up to 6 meter height or depth

below G.L. for all diameters

Do – deformed (TMT) bars confirming to relevant IS Fe – 500 grade for all

Refilling the pipeline trenches including ramming, watering, consolidating

disposal of surplus stuff as directed within a radius of 3 Km.

(I) Refilling as Directed

15.1 (II) do with selected soil brought from outside including all lead 772 cu.m. 201.25

Ambaji Under Ground Drainage Under SJMMSVY

Civil Work of Construction of Terminal Sewage Pumping station (TSPS)

Item Description Qty. Unit Rate in Rs.

1 Excavation for foundation with shoring & strutting if required as per 336.00 cu.m. 102.35

required gradient and line including all safety provision using site rails

and stacking excavated stuff including up to all required lead cleaning

the site etc. complete for all lift and strata as specified.

I) In all sort of soils and soft murrum

1.1 II)In hard murrum, boulders incl. macadam road. 224.00 cu.m. 155.25

1.2 III) In soft rock and/or masonry in CM or L M or Lime Concrete. 224.00 cu.m. 187.45

1.3 IV) In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking, 336.00 cu.m. 427.80

chiseling, or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

In hard rock and / or in C. C. 1:2:4 or RCC with blasting, breaking,

chiseling, or by chiseling/breaking only.

2 Refilling the pipeline trenches incl. ramming, watering, consolidating 559.00 cu.m. 25.30

desposal of surplus stuff as directed within a radius of 3 km..Refilling as

Refilling the pipeline trenches incl. ramming, watering, consolidating

desposal of surplus stuff as directed within a radius of 3 km.--do-- with

selected soil brought from outside including all lead

4 Anchor bars below RCC raft slab including drilling of necessary size hole 1345.00 No. 1893.00

in dry or wet condition, grouting with hilti OR EQUILVANT in dry or wet

condition, including random pull out test for 5% of total bars anchored

as per drawing and instruction of engineer-in-charge, (excluding cost of

TMT Bars) (In Hard Rocky Strata)

Ambaji Under Ground Drainage Under SJMMSVY

Civil Work of Construction of Terminal Sewage Pumping station (TSPS)

Item Description Qty. Unit Rate in Rs.

5 Providing and casting in situ C.C. in grade M-15 (approx. corresp. to 80.00 cu.m. 5641.90

prop. 1:2:4) (proportions as per mix design or as per Table 9 of IS456

2000 in masses by weigh batching ) using granite, quartzite trap metal of

size 6 mm to 20 mm for RCC work, including scaffolding centering,

form work, needle vibrated consolidation, curing comp. up to 6 meter

depth or height (excluding cost of reinforcement and neat finishing) with

centering and shuttering/deshuttering etc. comp. for structure for other

than water retaining. Footing (With form work)

6 Providing and casting in situ C.C. in grade M-15 (approx. corresp. to 41.00 cu.m. 5441.80

prop. 1:2:4) (proportions as per mix design or as per Table 9 of IS456

2000 in masses by weigh batching ) using granite, quartzite trap metal of

size 6 mm to 20 mm for RCC work, including scaffolding centering,

form work, needle vibrated consolidation, curing comp. up to 6 meter

depth or height (excluding cost of reinforcement and neat finishing) with

centering and shuttering/deshuttering etc. comp. for structure for other

than water retaining. Footing (Without form work)

7 Providing and cast in situ C.C. in grade M-30 proportions of ingredients 320.00 cu.m. 9444.95

as per mix design by weigh batching using granite, quartzite trap metal

of size 12 mm to 20 mm and or 6 mm to 12 mm including scaffolding

centering formwork, needle vibrated consolidation, curing and hydraulic

testing etc. complete (excluding cost of reinforcement) with centering

and shuttering/deshuttering etc. camp. up to 6 meter height /depth Av.

G.L.for all water retaining structures.

R.C.C. base slab

7.2 R.C.C. staircase 1.00 cu.m. 9654.25

7.3 R.C.C Beams 60.00 cu.m. 9758.90

7.4 RCC Column 40.00 cu.m. 10714.55

7.5 R.C.C. Top slab & Platform 40.00 cu.m. 9444.95

8 Providing and cast in situ C.C. in grade M-25 proportions of ingredients 40.00 cu.m. 9599.05

as per mix design by weigh batching using granite, quartzite trap metal

of size 12 mm to 20 mm and or 6 mm to 12 mm including scaffolding

centering formwork, needle vibrated consolidation, curing and hydraulic

testing etc. complete (excluding cost of reinforcement) with centering

and shuttering/deshuttering etc. camp. up to 6 meter height /depth Av.

G.L.for all water retaining structures.

a) R.C.C. beams, lintels and bracket for gantry or chain pully blocks,

plinth beams, tie beams.

8.1 b) R.C.C. slabs and platform 40.00 cu.m. 9288.55

8.2 c) R.C.C. weather shed, pardi & staircase 10.00 cu.m. 9288.55

8.3 d) R.C.C. columns 20.00 cu.m. 10574.25

8.4 e) R.C.C. footing 3.00 cu.m. 9288.55

Ambaji Under Ground Drainage Under SJMMSVY

Civil Work of Construction of Terminal Sewage Pumping station (TSPS)

Item Description Qty. Unit Rate in Rs.

9 Supplying cutting, bending, binding and placing in position steel as per 257.00 MT 77285.20

plan and design and as per ISS 2502 including cost of steel and binding

wire for reservoirs/structures only including lift up to 6 meter height or

depth below G.L. for all diameters. Do-deformed (TMT) bars confirming

to relevant IS Fe-500 grade for all diameters.

10 Grouting with 1:3 cement mortar for anchor bolt pockets machine bases, 5.00 cu.m. 3566.95

pipe sleeves, pocket holes etc. including roughening and cleaning of

concrete surfaces curing etc. complete.

11 Providing 20 mm thick Cement plaster in Cement mortar (1:2) using 2500.00 smt 232.30

water proofing compound of approved quality including finising etc .

12 Providing and applying 20 mm thick sand faced cement plaster at 430.00 smt 320.70

outside RCC / brick on work upto height 10 mtr. above ground level

consisting of 12 mm thick backing coat of C. M. 1:3 (1 cement : 3 sand)

and 8 mm thick finishing coat of C. M. 1:1 (1 cement : 1 sand) etc.

13 'Providing and applying 15 mm thick cement plaster in single coat on 360.00 smt 234.35

brick work with floating coat of net cement slurry for interior plastering

of pumphouse and outside plastering of sump upto finished even and

smooth in Cement motar 1 : 3 (1 cement : 3 sand) including racking out

joint curing, scaffolding required if any, with necessary cement finishing

etc. complete as directed.

14 Providing and applying 10 mm thick cement plaster in single coat on 440.00 smt 138.64

concrete work for interior plastering upto floor two level finished even

and smooth in Cement mortar 1 : 3 (1 cement : 3 sand) in a single coat

over RCC slab (on ceiling) etc. complete as directed.

15 Providing and laying 40 mm thick heavy duty cement concrete flooring in 270.00 smt 382.11

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) with water proofing compound and ironite powder

including finishing with a floating of neat cement etc. complete laid in

one layer in wet well area below GL, and for platform of pumphouse

16 Providing and applying epoxy paint of approved make to concrete 2614.00 smt 103.50

surface for RCC structure including cleaning the surface by scrapping and

air blowers to the satisfaction of Engineer-in -charge necessary

scaffolding etc. complete with all leads and lifts and giving satisfactory

hydraulic test for water tightness as per IS codes. For new surface-Two

17 Wall painting (two coats) with plastic emulsion paint of approved brand 436.00 smt 83.18

and manufacture of undercoated wall surface to give an even shade

including thoroughly brushing the surface free from mortar dropings and

other foreign matter and sand papered smooth.

Ambaji Under Ground Drainage Under SJMMSVY

Civil Work of Construction of Terminal Sewage Pumping station (TSPS)

Item Description Qty. Unit Rate in Rs.

18 Distempering in 3 coats with oil bound distemper of approved brand and 791.00 smt 106.74

manufacture and of required shade on wall surface to give an even

shade over and including a primer coat with distemper primer of

approved brand, thoroughly brushing the surface free from mortar

dropping and other foreign material and also inclusive of preparing the

surface even and smooth etc. complete, as directed on interior wall

surface for pumphouse.

19 Providing & fixing in position aluminum fully paneled doors with 15 3.00 smt 3024.00

micron natural matt brush finish anodized as per over all size shown on

the drawings and aluminum sections of approved make conforming to

IS:733 and IS : 1285, made out of 102 mm x 45 mm x 1.90 mm thick

aluminum outer frame section weighing 1.640Kg/m. and shutter sections

with bottom / lock rail 96 mm x 45 mm x 2.7 mm, top rail 48 mm x

mm x 2.70 mm weighing 1.38 Kg/m. vertical styles 48 mm x 45 mm x

1.90 mm weighing 0.976 Kg/m. with rounded sides, fixed with roll plugs

and screws or with fixing clips, or with expansion hold esters including

necessary filling up of gaps at junctions, at top, bottom and sides with

required PVC/neoprene felt etc. and aluminum snap beading for glazing

/ paneling, C. P. brass/stainless steel screws, including standard anodized