ADDN/ALTN AND SPECIAL REPAIRS TO BUILDING NO P-63 OF FATS, GARUDA, KOCHI

Amount

Dismantling Plain or corrugated steel / AC sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings/ cladding/ wall covering complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling structural steel members such as channels angle iron, tubular frames and flat etc and steel sections of any description by gas cutting or other means complete all as specified and directed.

S&F MS tubular frames including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 Gde St-240 including provn of one shop coat of zinc primer complete all as specified and directed.

S&F Rolled sections Fe 410-W (Gde-E- 250) quality-A as in main and cross beams, hip and jack rafters; purlins whee connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates including provn of one shop coat of zinc primer complete all as specified and directed.

M&L for preparation of steel and iron surfaces of any description over 10 cm in width or girth not otherwise described with two coat of synthetic enamel paint complete all as specified and directed.

Taking down cement or cement lime plaster from brick work or stone wall etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15 mm thick plaster in cement mortar 1:4 on other than fair faces of brick work or on concrete surfaces finished even and smooth with and including WPC complete all as specified and directed. Note :- WPC shall be measured and paid seperately.

M&L for 10 mm thick rendering in CM 1:6 on fair faces of brick work or on concrete surfaces finished fair and even complete all as specified and directed.

Supply only Integral water proofing compound

M&L for preparation of newly plastered surface of wall and applying three coats of white wash all as specified and as directed.

M&L for preparation of new or old plastered external wall surface ,scrubbing by using nylon/jute/wire brushes/scrapper blades or by using sanding machines to remove algae, moss, fungus and loosely adhered particles like dust, efflorescence etc and washing the surface with pressure jet washers and surface allowed to dry etc complete all as specified and as directed.

M&L for application of one coat of primer with sealant properties using "Seal-O-Prime" or "Weather coat exterior primer" ( of Berger make or equivalent make in other makes ) and allowed to dry overnight to receive first coat of emulsion paint complete all as specified and as directed. Note :- Before application of primer coat, the moisture of the wall surface shall be checked with a moisture meter .

M&L for application of first coat of exterior emulsion antifungal paint on primed wall surface using rollers made from foam or synthetic fibres,to get a smooth and tint free surface and allowed to dry for at least 8 hrs/ overnight to receive second coat of emulsion paint complete all as specified and as directed.

M&L for application of second coat of exterior emulsion antifungal paint on wall surface using rollers made from foam or synthetic fibres,to get a smooth and tint free surface complete all as specified and as directed. Note for Item No.20 to 23 :- Application through company authorised applicator or under company supervision using modern tools and techniques shall be ensured. contractor shall submit performances guarantee for a period of five years after completion as per prescribed format .

M&L for complete removal existing external treatment and preparation of old plastered external wall surface ,scrubbing by using nylon/jute/wire brushes/scrapper blades or by using sanding machines to remove algae, moss, fungus and loosely adhered particles like dust, efflorescence etc and washing the surface with pressure jet washers and surface allowed to dry etc complete all as specified and as directed.

M&L for application of one coat of primer with sealant properties using "Seal-O-Prime" or "Weather coat exterior primer" ( of Berger make or equivalent make in other makes ) and allowed to dry overnight to receive first coat of emulsion paint complete all as specified and as directed. Note :- Before application of primer coat, the moisture of the wall surface shall be checked with a moisture meter .

M&L for application of first coat of exterior emulsion antifungal paint on primed wall surface using rollers made from foam or synthetic fibres,to get a smooth and tint free surface and allowed to dry for at least 8 hrs/ overnight to receive second coat of emulsion paint complete all as specified and as directed.

M&L for application of second coat of exterior emulsion antifungal paint on wall surface using rollers made from foam or synthetic fibres,to get a smooth and tint free surface complete all as specified and as directed. Note for Item No.20 to 23 :- Application through company authorised applicator or under company supervision using modern tools and techniques shall be ensured. contractor shall submit performances guarantee for a period of five years after completion as per prescribed format .

Dismantling of wall and ceiling boards (fiber, pulp insulation etc.) or insulation boards / slabs / blankets, any thickness including fillet complete all as specified and as directed.

M&L for 12 mm thick perforated particle board / tiles for insulation and accoustic purposes 60 x 60 cm in size fixing with flat screw in wooden fillets in walling complete all as specified and directed.

S&F 4 mm thick Non asbestos fibre cement building at any height fixed or laid/ inserted to timber/GI/Aluminumframe work with screws in ceiling flat or slopping complete all as specified and directed.

M&L for preparation of new perforated board/fiber cement board surfaces (wall) and applying two coat of oil bound distemper over a coat of primer complete all as specified and directed.

S&F aluminium snap grid false ceiling on frame work of angle 25x25x2 mm, Main TEE 38x25x1.5 mm and cross TEE 25x25x1.4 mm and size of grid 605x605 mm with hangers 6 mm dia GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.50 mm dia, 40 mm long with including necessary scaffolding complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls including cornices (plastered or unplastered) and applying one coat of distemper oil emulsion complete all as specified and directed.

Dismantling of single layer Mangalore pattern or similar tiles in roofing laid dry including ridge tiles laid bedded and jointed in CM complete all as specified and directed.

M&L for Mangalore pattern roof tiles, interlocking at side joints, laid dry complete all as specified and as directed.

M&L for ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in cement mortar 1:6 complete all as specified and as directed.

Dismantling timber scantlings over 40 Sqcm in section for unframed work complete all as specified and as directed.

M&L for IInd class HW in wooden scantling clean sawn for unframed work in any position with nails complete all as specified and directed complete all as specified and directed.

Dismantling timber battens for tiles,shingles etc of any size including tilting fillets complete all as specified and as directed.

M&L for IInd class HW clean sawn battens at 30 cm centres,scetional area exceeding 5 Sqcm and not exceeding 15 Sqcm complete all as specified and directed complete all as specified and directed.

Taking down existing water proofing treatment from the roof including cement mortar bedding, removing debris outside MD land and cleaning the roof surface complete all as specified and as directed.

M&L screed bed or bedding layer of mortar 15 mm thick in CM 1:3 on concrete surface, mixed with and including WPC finished even and smooth without using extra cement. (Note:- WPC shall be measured and paid separately. Dosage of WPC shall be as per direction of manufacturer)

M&L for water proofing treatment by applying oil bound bitumen @ 0.20 kg/sqm providing and laying 4 mm thick APP modified water proofing membrane weighing not less than 4.00 Kg/Sqm reinforced with one woven polyester mat weighing not less 160g/Sqm having softening point not less than 140 degree centigrade longitudinal tensile strength not less than 650 N/5 cm, tearing strength of 180 N (Min),a static puncher resistance of 180,torch application including minimum 10 cm side over lap & 15 cm end overlap and applying a coat of blown grade hot bitumen 85/25 before and over the membrane 1.20Kg/Sqm finishing with solar reflective bituminous based aluminium paint @ 0.10Kg/Sqm all as specified (four course treatment) in clause 11.40.3.3 of SSR Part I and Particular specification.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exc 1.5 sqm but not exc 4 sqm each, all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area not exc 1.5 sqm each ,all as specified and as directed.

S&F for powder coated aluminium frame work for doors, sliding windows, ventilators and partitions with one or more rebates including joining cleat for fixing etc. Complete all as specified (minimum thickness of powder coating 50 micron) complete all as specified and directed.

S&F powder coated aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. (minimum thickness of powder coating 50 micron) complete all as specified and directed.

S&F 5.50 mm thick sheet glass, ordinary quality and glazing in squares area exc 0.50 sqm in each Pane

S&F 12 mm thick Prelaminatd particle board, exterior grade, prelaminated both side with decorative choice lamination, fixed with screw complete all as specified and as directed.

S&F powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) (minimum thickness of powder coating 50 micron) complete all as specified and directed.

S&F 4 mm thick sheet glass ,ordinary quality and glazing in square n exc 0.5 sqm in each pane complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per SSR specification & drawing complete all as specified and directed

S&F factory made solid panel PVC door shutter 28 to 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement or stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed

M&L for preparation of old wooden surfaces of any description, exc. 10 cm width of girth and applying one coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F 100 mm size, butt hinges medium weight cold rolled mild steel bright polished complete all as specified and directed.

S&F 75 mm size, butt hinges medium weight cold rolled mild steel bright polished complete all as specified and directed.

S&F M.S Hold fasts of FI 25 x 3 mm confirming to Fe290 Gde E 165 fixed in and including plain cement concrete 1:3:6 type C1 using (20mm graded crushed stone aggregate) including treated with tar or coal tar black paint complete all as specified and directed

S&F 100mm long extruded aluminium alloy handles, cast type, anodised complete all as specified and as directed.

S&F 150mm long aluminium anodized barrel tower bolt of extruded section ccomplete all as specified and directed

S&F 4 mm thick, 40 mm wide rubber beading fixed to aluminium shutter/frame with stainless steel screw 12 mm long complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for Vitrified tiles 10 mm thick dark shade, double charged /ultra charged (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc, set and jointed neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed in CM 1:4 all as specified and as directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm tk screed bed of CM 1:6 all as specified and as directed.

M&L for Glazed ceramic tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade over and including 10 mm thick rendering CM 1:3 all as specified and as directed.

M&L for rolled steel sections (Fe 410 W,grade E-250) quality A as in framing for cladding,glazing and the like fixed with angle cleats and connecting plates including removal after completion of work in simulator room complete all as specified and as directed.

S&F plywood,grade BWP, type BB 12 mm thick,fixed with screws to steel frame work with proper sealing in joints to avoid leakage ,covering with polythene sheets (min 50 Microns) for arresting the entry of dust and water inside the box and keeping dust free during the entire contract period and including removal after completion of work in simulator room complete all as specified and as directed. Note :- The quoted rate also shall deemed to include the cost of polythene sheet as specified above.

Demolition of brick work or stone, boulder, precast PCC block masonry including all quoins, arches, pillar, etc. built in cement mortar or cement lime mortar complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts,wells,cesspits,manholes,pier holes,etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in soft soil.

Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc. 25cm. deep with approved soil obtained from excavation

Removing excavated material to a distance n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

Excavating in post holes in soft/loose soil (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed.

M&L for PCC 1:4:8, Type D2 using 40 mm graded stone aggregate in foundation, filling and mass concrete complete all as specified and as directed.

M&L for PCC 1:2:4, Type B1 using 20 mm graded stone aggregate in foundation, filling and mass concrete complete all as specified and as directed.

M&L for reinforced cement concrete type B1, 1:2:4 (nominal mix) using 20mm graded stone aggregate in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed

M&L for reinforced cement concrete type B1, 1:2:4 (nominal mix) using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and inshelves and the like complete all as specified and directed

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat or rough finished surfaces of concrete complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs fair finished such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L for 5 mm thick rendering in CM 1:3 on concrete ceiling surfaces finished fair and even complete all as specified and directed.

M&L for preparation of new ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry with solid blocks, Type C1 (1:3:6) using 20mm graded stone aggregate, exc. 10cm in width and setting in cement mortar 1:6 complete all as specified and as directed.

S&F 150 mm long Brass, barrel tower bolt complete all as specified and directed.

S&F 200 mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled complete all as specified and directed.

S&F Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed.

S&F 110 mm dia PVC (SWR) Pipe single socketed in any length with rubber joints laid in trenches or in floors complete all as specified.

S&F 110 mm dia PVC (SWR) Pipe single socketed in any length with rubber joints fixed on walls complete all as specified.

S&F in repairs 110 mm dia PVC (SWR) 'P' trap incl jointing with solvent cement complete all as specified and as directed.

S&F in repairs 75 mm PVC (SWR) floor trap plain with grating incl jointing with solvent cement complete all as specified and as directed.

S&F 110 mm dia PVC (SWR) pipes vent cowl complete all as specified and as directed.

S&F Vitreous china wash down water closet pan (pedestal pattern) white incl fixing bolts, plastic water closet seat cover white closed pattern with flat bottom and cover including PVC valve less,low level flushing cistern ,10 ltr capacity white symphonic action with inlet, ball valve, float and handle including flush pipe and brackets and flush pipe of polyethylene of low or high density or PVC 32 mm dia and MS CP or aluminised hinging device and connection to drain and flushing pipe, antisyphonage pipe etc complete all as specified and as directed.

S&F in repairs Vitreous chinaware wash hand basin white (flat back) of size 550x400mm including brackets and provn of pillar taps fancy type 15mm dia cast copper alloy with capstan heads , Chromium plated screwed down high pressure with or without lettered "Hot " or "cold" with long screwed shanks and fly nuts , screwed for iron pipes complete all as specified and as directed.

S&F Waste coupling of PTMT with discharge pipe 32mm bore (half or full threaded) Minimum wt 32mm-45 gms complete all as specified and directed.

S&F in repairs PVC connection 15 mm size with PTMT nuts of length 450 mm long complete all as specified and directed .

S&F toilet paper Holder Recessed Type (Stainless Steel) complete all as specified and directed. Make : JAQUAR Cat part No. AHS-1551 or Equivalent model from the manufactureres in the list as approved by GE.

S&F towel rail 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms) complete all as specified and directed.

M&L for hardcore of gauge n exc. 63 mm, using broken stone broken or boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for providing 100mm thick cement concrete, Type D2, 1:4:8 using 40mm graded stone aggregate as in sub base of floor / hard standing etc complete all as specified and as directed.

M&L for plain cement concrete Type C-2, 1:3:6 (using 40mm graded crushed stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes (150mm bore pipe) after the pipe are laid and tested complete all as specified and directed.

M&L for 150mm dia slat -glazed stoneware drain pipes laid in trenches and joints complete all as specified and directed.

M&L For salt -glazed stoneware gully traps, of size 180x100mm square or round mouthed, type 'P' complete all as specified and directed.

S&F Hume pipe septic tank 50 users capacity including necessary earth work in soft/ loose soil, PCC 1:3:6 in bed concrete with accessories like AC vent pipe, cowl manhole cover etc including connecting to the sewer line complete all as shown in drg No.TD/A/57 sheet 1/1 including removal of old septic tank and connected works complete all as specified and as directed by Engineer-in-Charge.

S&F Brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed

M&L for providing 50mm thick cement concrete, Type B1, 1:2:4 using 20mm graded stone aggregate as in sub base of floor / hard standing etc complete all as specified and as directed.

M&L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed in CM 1:4 complete all as specified and as directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment over and including a 50mm thick layer of coarse aggregate for granolithic floors graded from 12.5mm to 4.75mm Spreading and leveling in layers n exc. 25 cm thick , well ramming including watering as required complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M&L for point wiring with 1.5 sqmm nominal cross-sectional area, single core PVC insulated (FRLSH), unsheathed with proper colour coding multistranded copper conductor cable ISI marked 1100 Volts grade cinforming to IS-694-1990 as amended up to date . drawn through and including PVC casing capping (FR ) medium grade,suitable size with accessories and fixing screws and making good surfaces to match the existing finishes and factory made galvanised sunken box of 1.6 mm thick with modular cover plates for fixing of switches sockets and fan regulators etc including 1.5 Sqmm nominal cross sectional area, single core PVC insulated (FRLS), unsheathed multistranded copper conductor cable earth continuity wire to common earth and connected to earth dolly for one light /fan point controlled by one switch of 6 Amp, single pole one way complete all as specified and directed

All as per item No.102 above but for One fan point / exhaust fan point controlled by one switch & regulator

All as per item No. 102 above but for One 5 pin 5 Amps Socket point controlled by one switch on same board.

All as per item No102 above but for One 5 pin 5 Amps socket point controlled by one switch on independent board.

All as per item No.102 above but with 2.5 Sqmm copper conductor including 2.5 Sqmm copper cable as earth wire for one 6 Pin 16 Amps Socket outlet on independent board.

All as per item No.102 above but with 4 Sqmm copper conductor including 4.0 Sqmm copper cable on earth wire for sheet metal enclosure

S&F Switch modular 6 Amps 230 Volts one way switch all as specified and as directed. Make: Cat part No 675501 of Legrand 'Mylinc' ,Philips Cat No. 913713659901 ,Crabtree Cat No. Athena ACASXXW061.

S&F Ceiling rose three terminal polycarbonate isolated body AC 230 volts complete all as specified and directed.

S&F socket modular 6 Amps AC 230 Volts 2/3 pin combined 2 modular type complete all as specified and as directed. Make: Legrand 'Mylinc' Cat No 675550 ,Philips Cat No. 913713661901 ,Crabtree Cat No. Athena ACARFHW005.

S&F Socket 6A/16 Amps - 2/3 pin combined AC 230 Volts modular type complete all as specified and as directed. Make Legrand 'Mylinc' Cat Part No 675555 Anchor Roma/Siemens.

S&F switch modular type AC 230 volts 16 Amps one way complete all as specified and as directed. Make Legrand 'Mylinc' Cat part No 675511 Anchor Roma/Siemens.

Supply and fix LED flat panel with high brightness with glare free recessed 2 feet by 2 feet 36/40 Watt endura slim pro plus fitting including all connection all as specified and directed. Make:- Havells Cat Part No. ENDURASLIMPROPLUS 2X2PLR28 / 36WLED857MOD / Crompton Cat Part No. LCTLRN-36-FO-CDL / Philips Cat Part No. RC380BLED36S - 6500G4L60PSUOD.

S&F Regal Batten for LED tube lights, both side connection type and LED tube rod 1 x 20 Watt, both side connection all as specified and as directed. Make of batten : Havells Cat Part No. Regal batten 8UPT001X22WSSBSWH / Crompton Cat Part No. IGP131LT8-16 / Philips Cat Part No. TMC501P1XTLED22WP3241 Make of tube rod : Havells Cat Part No. Crystal 1213T8DSTL20W LED 865 GLASS / Crompton Cat Part No. LG-T8-20-865-2 / Philips Cat Part No. Essential LED tube 1200mm 20W865T865T81ND-1

S&F tube light fitting 2 X 18 with T8 LED tube of 18/20 Watt with aluminium Extrusion heat sink for optimum performance with high luminous efficiency and batten pre wired suitable to use with LED tube with concealed accessories complete. Make : Havells model No. REGALBATTENT8UPTO 2X22WDSBSWH and CRYSTAL1213T8DSTL18WlED 865SGLASS (2 Nos) / Crompton Cat Part No. IGP162LT8-16 and Tube rod LT8-20-865

S&F LED down lighter, 12 W,240 volt recessed round polycarbonate housing with superior light output and integral driver high efficiency 100lm /W all as per specified and directed. Make:- Crompton Cat Part No. LSDEP-12-CDL / Philips Cat Part No. 94051090 / Jaquar Cat Part No. LNEP01R012XC

S&F LED Mini mirror light 1 x 10W/12W Watt Wall/Surface mounted luminaries with engineering plastic housing, wired with all accessories complete incl provn of flexible copper wire from ceiling rose to light fitting terminal. Make :Crompton Cat No. LDL-10-WW, Luker Cat Part No. LTSM10, Philips B No 21LED12S

Taking down ceiling fan / exhaust fan, painting of fan complete with two coat of anticorrosive paint over a coat of primer by spraying including filling cavities and rehanging ceiling fan and connecting up including provision of cable(copper wire) from ceiling rose in connector to fan 230V all as specified and as directed.

S&F Modular Fan Regulator electronic rotary, 0-4 steps step type 100 watts, 240 Volt, 50 HZ hum free module complete all as specified and directed. Make: Legrand 'Mylinc' Cat No 675530 or equivalent model of any other manufacturers from the list.

S&F Sheet metal enclosures with socket plug top and MCB' single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 A MCB. Make: Havells, Cat Part No. DHDMCSN 0251020/ L&T Cat Part No. DBMPS120SD/ Schneider Cat Part No. A9HMS220

S&F Sheet metal enclosure TPN for DB's when MCB's to be used 4 way with 200 amps bus bar double door. Make: Schneider Cat Part No. A9HTND04/ L&T Cat Part No. DBTPE004DD/

S&F Sheet metal enclosure MCB TPN DB 8 way double door IP 43 type suitable for 200 amp including all electrical connection all as specified and as directed. Make: Schneider Cat Part No. A9HVTD08 / Legrand series XLᶟ 6300 enclosure / L&T Cat Part No. DBPSG008DD

S&F Sheet metal enclosure MCB TPN DB 12 way double door IP 43 type suitable for 200 amp including all electrical connection all as specified and as directed. Make: Schneider Cat Part No. A9HVTD12 / Legrand series XLᶟ6300 enclosure / L&T Cat Part No. DBPSG012DD

S&F Sheet metal enclosure MCB SPN DB 8 way double door (metal door) IP 43 type suitable for 200 amp\ including all electrical connection all as specified and as directed. Make : Schneider Cat Part No. A9HSNS08 / L&T Cat Part No. DBSPN008SD / Legrand Cat Part No. XLᶟ400

S&F MCCB 4 pole 250 Amp 415V 36KA adjustable type all as specified and directed. Make : L&T Cat Part No. CM90642OOPO/ Legrand Cat Part No. DPXᶟ Series - 420259/ Schneider Cat Part No. LV431630.

S&F MCB 'C' Curve 100 Amp Three pole, 415 Volts, all as specified and directed. Make: L&T Cat Part No. AU15S31003C/ Legrand Cat Part No. 408663/ Schneider Cat Part No. A9N18367

S&F MCB 'B' Curve 63 Amp Three pole, 415 Volts, all as specified and directed. Make: L&T Cat Part No. BB30630B /Legrand Cat Part No. 408620/ Schneider Cat Part No. A9NIP63B.

S&F MCB 'B' Curve 63 Amp SPN ,240 Volts all as specified and directed. Make: L&T Cat Part No. BB20630B / Legrand Cat Part No. 408620/ Schneider Cat Part No. A9NIP63B.

S&F MCB 'B' Curve SP 6 To 40 Amp , 240 Volts, all as specified and directed. Make : Schneider Cat Part No. A9N1P06B-32B / L&T Cat Part No. BB10320B / Legrand Cat Part No. 408587-408596

S&F RCCB 63 Amp For earth leakage protection four pole 100 mA all as specified. Make: Schneider Cat Part No. A9N16209/ Legrand Cat Part No. 411883/ L&T Cat Part No. BG406310

S&F 250mm sweep, PVC body exhaust fan heavy duty, single phase 230 Volts, all as specified & directed. Make: Havells Cat Part No. Ventil Air-DX white or equivalent Bajaj/ Crompton

M&L (in repair) for sub main wiring with two runs of single core 4 Sqmm (FRLS) multistranded copper conductor PVC unsheathed cable drawn through and including PVC conduit of not less than 20 mm dia concealed in wall/floor including cutting chasses and making good the wall/ceiling / floor for sub main connection including 4.0 Sqmm (FRLS) PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly complete all as specified and directed. Note :- (i)Three runs of 4 Sqmm (FRLS) copper conductor and one run of PVC conduit shall be measured as one unit length.

M&L (in repair) for sub main wiring with two runs of single core 6 Sqmm (FRLS) multistranded copper conductor PVC unsheathed cable drawn through and including PVC conduit of not less than 20 mm dia concealed in wall/floor including cutting chasses and making good the wall/ceiling / floor for sub main connection including 6.0 Sqmm (FRLS) PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly complete all as specified and directed. Note :- (i)Three runs of 6 Sqmm (FRLS) copper conductor and one run of PVC conduit shall be measured as one unit length.

M&L (in repair) for sub main wiring with four runs of single core 6 Sqmm (FRLS) multistranded copper conductor PVC unsheathed cable drawn through and including PVC conduit of not less than 25 mm dia concealed in wall/floor including cutting chasses and making good the wall/ceiling / floor for sub main connection including two runs of 6.0 Sqmm (FRLS) PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly complete all as specified and directed. Note :- (i) Six runs of 6 Sqmm (FRLS) copper conductor and one run of PVC conduit shall be measured as one unit length.

M&L (in repair) for sub main wiring with four runs of single core 10 Sqmm (FRLS) multistranded copper conductor PVC unsheathed cable drawn through and including PVC conduit of not less than 25 mm dia concealed in wall/floor including cutting chasses and making good the wall/ceiling / floor for sub main connection including two runs of 10.0 Sqmm (FRLS) PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly complete all as specified and directed. Note :- (i) Six runs of 10 Sqmm (FRLS) copper conductor and one run of PVC conduit shall be measured as one unit length.

M&L in repair for earthing complete with galvanised steel earth plate electrode 60 cm x 60cm x6 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meters below normal ground level, connected to GI earth lead wire 4mm dia upto length 7.5 mtr by means of bolts, nuts and washers of galvanised steel all as shown in electrical plate No. 3 connected to earthing test point complete all as specified and indicated including testing on completion including taking out old, earthing complete. Note : The rate is deemed to be inclusive of the cost of complete earth work in any type of soil. PCC 1:3:6 type C-1 for chamber,RCC 1:2:4 type B1 for precast cover slab 50 mm thick, reinforcement 8 mm TMT bars @ 150 mm c/c both way, necessary form work, handle, charcoal dust 20mm dia GI med grade for watering and 15 mm dia GI light grade earth lead protection pipes with funnel and wire mesh complete all as specified and directed..

S&F in repair Integral aviation obstruction light fitting comprising of aluminium housing with polycarbonate enclosure including fixing arrangement and connection complete all as specified and as directed. Make: Cat part no BGAV 302 LED of Bajaj or equivalent in Philips/Wipro .

S&F Building security light made up of pressure die cast housing with toughened glass and high power LEDs with option of secondary optic with IP 66 protection of 30 Watt including suitable GI bracket of 25 mm dia and fixing arrangement on walls all as specified and directed including taking down of existing light fitting of any type and make. Make: Crompton Cat Part No. Cat Part No. LSTS-30-CDL/NL-M/ Philips HSN code 94054090/ Jaguar Cat Part No. LPCRSRT30WXW.

S&F LED flood light made up of pressure die cast housing with toughened glass and high power LEDs with option of secondary optic with IP 66 protection, 3000 K, with 10 KV SPD of 50 watt of all as specified and directed including taking down of existing light fitting of any type and make. Make: Crompton, Cat Part No. LFL-50-CDL/ Jaguar Cat Part No. LFLD02S050XW/ Philips Cat Part No. BVP 161 LED 43 NW/CW/WW 50W

S&F independent Telephone Socket RJ11 with Transparent shutter one module complete. Make - Legrand Cat No. 673052 ,Crabtree Cat No. Athena ACAKHAW000, Philips Cat No. 913713913149.

S&F Rigid non-metallic PVC concealed conduit 20 mm dia (for running Telephone wire) and cutting chases including provn of junction/ terminal box & all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.

S&F on wall/Floor/Ceiling /Concealed in wall high pressure CPVC pipes SDR-13.5 & plain CPVC SDR 11 fittings including all necessary fittings, like Elbow, Tee, Socket , Reducer, bushings , step over bends ,end caps, End plugs, etc and with CPVC solvents cement of size 25 mm dia complete all as specified and directed. Make: Supreme/Eurotech /Astral/SFMC Note:- Cutting /Chases on wall / floor will be measured and paid separately under the relevant item if required.

All as per item No. 142 above but CPVC Pipe of size 20 mm dia.

S&F CPVC Ball Valve of size 25 mm dia suitable for CPVC pipe incl necessary fittings complete all specified and directed. Make: Supreme/Eurotech /Astral/SFMC

All as per item No. 144 above but CPVC Ball valve of size 20 mm dia.

S&F of Bib cock , CP quarter turn with flange and aerator, fancy type short body cast copper alloy with crutch or butterfly handle screwed for GI/ CPVC pipe of size 15 mm complete all as specified and directed. (Make : Model No F2004151 of Cera or equivalent of praying/hind ware/Jaguar)

S&F of Bib cock, CP quarter turn with flange and aerator, fancy type long nose with wall flange cast copper alloy with crutch or butterfly handle screwed for GI/ CPVC pipe of size 15 mm complete all as specified and as directed. (Make : Model No F2004152 of Cera or equivalent of praying/hind ware/Jaguar)

S&F 15 mm angle valve, half turn with flange, with flange type chromium plated for fixing accessories for CPVC pipe complete specified and as directed by the Engineer-in-charge (Make : Model No: F2004201 of Cera or equivalent of Hind ware/Jaguar)

S&F of swivel overhead shower (minimum weight 40 grams) of PTMT any colour with shower arm (minimum weight 40 grams) 15mm size, 195 mm long with bend of 45 degree with flange for fixing with CPVC pipe complete all as specified and directed. (Make : Model No: F7020307 of Cera (shower head) & F7040202 (Shower arms) or equivalent of Hind ware/Jaguar).

S&F PVC connection pipe 16mm dia (outer 450mm long cold water and taking down old one complete with brass union on both sides to suit 15mm GI pipe and taking down old one, complete all as specified and directed.

S&F health faucet ABS body with wall hook and 1 metre SS braided rubber hose pipe , including taking out old one complete all as specified and directed. (Make : Model No: F8030102 of Cera or equivalent of praying/hind ware/Jaguar).

S&F concealed stop cock regular body, Quarter turn with adjustable wall flange chromium plated with CP cup fancy type of size 20mm complete all as specified and directed. (Make : Model NO: F2004351 & F 4050102 of Cera or equivalent of praying/hind ware/Jaguar)

S&F CP angle cock, self closers / pressmatic with flange for urinal pots to fix in 20/15 mm pipe complete all as specified and directed by Engineer-in-charge. Make:- Model No F9020203 of Cera or equivalent of Prayag/Jaguar

S&F of Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position of capacity 1000 litrers complete all as specified and directed. Make : Sintex (ISI)/ Aquatech

S&F float valve synthetic(PVC) of size 25 mm dia high pressure with polythene ball of size 6" dia and flynut complete all as specified and directed.

M&L for cutting chasses on walls floor etc not exceeding 20 cm girth and making good the disturbed surface to match with the existing after removing the existing concealed pipe/laying new pipe, complete all as specified and directed.

Taking down Old unsv 25 mm GI Tubing and connections complete

Taking down old unsv 20 mm GI Tubing and connections complete

Taking down old unsv 25 mm CPVC ball valve

Taking down old unsv 20 mm CPVC ball valve

Taking down old unsv Bib cock

Taking down old unsv angle valve/ Stop Cock/ Angle cock self closers

Taking down old unsv shower arm, shower head

Taking down old unsv Health faucet

Taking down old unsv PVC connection pipe 16mm dia

Taking down old unsv Rotational moulded polyethylene water storage tanks 1000 ltrs including all accessories complete

Taking down old unsv 25 mm float valve

Dismantling of building external ducting, insulation materials and supporting etc outside of the building complete all as specified and directed.

S&F in trenches high pressure CPVC pipes SDR-13.5 & plain CPVC SDR 11 fittings including all necessary fittings, like Elbow, Tee, Socket , Reducer, bushings , step over bends ,end caps, End plugs, etc and with CPVC solvents cement of size 50 mm dia complete all as specified and directed.

S&F on wall high pressure CPVC pipes SDR-13.5 & plain CPVC SDR 11 fittings (concealed) including all necessary fittings, like Elbow, Tee, Socket , Reducer, bushings , step over bends ,end caps, End plugs, etc and with CPVC solvents cement of size 50 mm dia complete all as specified and directed.

All as per item No.170 above but for CPVC pipe 40mm dia

S&F in repair CPVC Ball Valve of size 50 mm dia suitable for CPVC pipe incl necessary fittings complete all specified and directed.

All as per item No.172 above but for CPVC pipe 40mm dia

S&F Monoblock Pump single phase 1 HP, 50 Hz including provn of suitable DOL starter complete all specified and directed.

Supply, assembly and errection of GI sheet 22 SWG GSS ducting (0.80 mm) with TDF flange rectangular/square duct as per IS:655 complete with all fitting such as tee, bends turning vanes, splitter dampers as required sizes of both supply and return air inspection doors transformation pieces etc including suspension and supporting arrangement for plenums ducts complete all as specified and directed.

S&F Spring actuated fire dampers with fusible link having a melting point 67+/- 3 Deg C and fire rating of 90 minutes and shall be tested as per UL 555 and certified by CBRI complete all as specified and directed.

M&L for Checking of existing condition of air ducts making the arrangement of visualization and the process for duct cleaning by using vacuum suctioning for indoor air quality of AC ducts inside the simulator area connection in between plenum and branches and main plenum with robotic camera, HEPA negative machine air compressor various type of air nozzles for maintain standard indoor air quality complete all as specified and directed.

S&F in repair acoustic insulation inside the duct nitrile rubber of 15mm thickness open cell foam with density 140-180 kg/m3 passing class 1 fire performance test as per BS 476 part 7, air erosion test for 10,000 fpm air velocity as per ASTM C 1071-05 and with built-in antimicrobial protection. The material should pass fungi resistance test as per DIN EN ISO 846 method A and Bacterial resistance test as per DIN EN ISO 846 method C to be applied using manufactures fasteners (4 at the corners of the metal strip and 1 at the centre) to be fixed per sqm sheet of the material complete all as specified and directed. Make : Armacell/ Armaflex/ Sperlone.

Supply & installation in replace of thermal insulation exposed ducting – class o armaflex with GC covering on outdoor ducts exposed to sunlight using closed cell class O nitrile rubber of 25 mm thickness elastomeric insulation of density 40-50 k/m3, thermal conductivity of 0.037 W/mk at 200 Celsius mean temp and 7000 (without any additional vapour barrier) and with chemically treated factory laminated woven fibre glass cloth with 200+/-20 gsm: to be applied on ducts using manufactures recommended rubber based adhesive in a blend of solvents complete as per specifications. Make : Armacell/ Armaflex or equivalent.

S&F 600mm X 600mm fresh air inlet made out of GI sheet 22 SWG duly fabricated with splitter damper arrangement and cowl and bird screen complete all as specified and directed.

S&F Canvas cloth superior quality with connection all as specified and directed.

S&F Supply/return air diffusers of machine fabricated made out of aluminium 18 G sheet construction of various sizes duly power coated of approved colour to suitable as existing duct projections/ opening including GI collar VCD for supply air inlet all as specified and directed.

S&F Auto shutdown safety device with provision of interlocking arrangement with the existing central AC plant and AHU in order to shutdown on emergency in case of the outburst of fie in side the duct including all necessary microprocessor based controlled accessories totally enclosed and fixed on suitable power coated panel duly fixed on wall/existing panel and control cabling complete all as specified and directed.

S&F Auto operation control panel microprocessor based for providing auto and manual control for the AC plant entire machineries so as to maintain a comfort temperature at serving area the logic of operation will control the temperature at serving area and same time the compressor, pump cooling tower will cut off depends on the AHU status and return air temperature. The control will reversely automatically operate when cooling demands on as per serving area requirement fixed totally enclosed on suitable power coated panel duly fixed on wall/existing panel complete all as specified and directed.

S&F Acoustic insulation inside the wall of AHU room at in side of the AC plant with engineered nitrile rubber of 25 mm thickness open cell foam with density 140-180 kg/m3 passing class 1 fire performance test as per BS 476 part 7 air erosion test for 10,000 fpm air velocity as per ASTM C 1071-05 and with built-in antimicrobial protection. The material should pass fungi resistance test as per DIN EN ISO 846 method A and bacterial resistance test as per DIN EN ISO 846 method C to be applied using manufactures recommended rubber based adhesive in a blend of solvent 2 metal strips in cross and 5 anchor fasteners (4 at the corner of the metal strip and 1 at the centre) to be fixed per sqm sheet of the material complete all as specified and directed. Make: Armacell / Armaflex.

Supply and fix air termination single pointed aluminium rod 12 mm dia and 300 mm long complete including taking down old air termination rod all as specified and as directed.

Supply and fix test point terminal block made of gun metal or phosphorus bronze of size 75 x75 x25 mm and screwed including 3 Nos 8 mm dia 25 mm long hexagonal head screw including PVC juction box complete including taking down old terminal block all as specified and as directed.

Supply and fix aluminium strip 25 x3 mm with saddles , insulators and fixing screws etc for roof conductors and down conductors on walls / above ground etc complete including taking down old strip all as specified and as directed.

M&L in repair for earthing complete with galvanised steel earth plate electrode 60 cm x 60cm x6 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meters below normal ground level, connected to GI earth strip 32x6 mm as earth lead upto length 7.5 mtr by means of bolts, nuts and washers of galvanised steel all as shown in electrical plate No. 3 connected to earthing test point complete all as specified and indicated including testing on completion including taking out old, earthing complete. Note : The rate is deemed to be inclusive of the cost of complete earth work in any type of soil. PCC 1:3:6 type C-1 for chamber,RCC 1:2:4 type B1 for precast cover slab 50 mm thick, reinforcement 8 mm TMT bars @ 150 mm c/c both way, necessary form work, handle, charcoal dust 20mm dia GI med grade for watering and 15 mm dia GI light grade earth lead protection pipes with funnel and wire mesh complete all as specified and directed..

Hiring charges for providing air conditioning for simulator cabin of size 9 m x9 mx9 m as temporary basis for maintaining the conditioned space with temperature 20 +/- 2 degree C and RH 50 +/- 10 during the working period complete with suitable capacity Air Conditioners , de-humidifiers,alongwith all supply and return air ducting, electrical connections,Air Handling Units ,controls etc with all 100% standby system complete all as specified and directed.

SHAIJAL T M

WELTRONENGINEERINGSERVICES