REPAIR AND DAY TO DAY MAINTENANCE WORKS TO FLOOR WALL ROOF SANITARY FITTINGS JOINERIES AND CERTAIN MISC WORKS OF B R NATURE ETC FOR MAIN HOSPITAL IN LIVING ACCNS MNS MESS AREA SANJIVANI HOUSE AND ALLIED BLDGS UNDER INHS

Amount

Notes 1. Contractor shall collect the complaint slip from complaint cell daily at 9.00 am and to be return after completion on same day (Except for major complaints).. 2. All complaints to be rectified in time. The Delay in rectification of complaint more than specified the penality will be levied @ Rs.1000.00 Per complaint. (a) Item No 1 to 35 complaint should be complete in 24 hours (b) Item No 36 to 168 complaint should be complete in 07 days except major complaint. (c) all Major complaint should be completed in 28 days “No complaint should pending more than 28 days” . (d) In case of any urgent / Emergency nature of work plumber/carpenter/mason should available 24 hours x 7 days should available for work and nothing extra shall be admissible on this account. 3. The complaints shall be communicated to the contractor/rep of contractor/ site engineer / site supervisor through Online compliant management portal/website, SMS, Telephonic calls, Letter / Register or other suitable mean of communication at any time. 4. All complaints related to Sanitary fittings / plumbing fittings/ Builders hardware, materials to be purchased as per approved make and kept in store in case of complaint immidiately to be attended. 5. The type of complaint will be decided by Engr-in-Charge. if contractor is not agreeing to the decision of Engr-in-charge the same shall be referred to the Accepting officer whose decision shall be final, binding and conclusive. 6. The quoted rates includes the scaffolding/staging upto 10 floor height and shaft portion etc. 7. The quoted rates include all the safety equipment's to be used like glouses, safety belts, helmets, mask, safety goggles etc

Attending complaints such as leakage and other petty repairs including providing and replacing minor items and spindle and ensuring proper and trouble free functioning of Pillar taps etc of any description or size, complete all as specified and directed by Engineer-in-Charge. Note:- . (a) Rectificatin of leakage by replacing tap washers, tightning the handle/knob/nuts/screws, tightning loosely fitted tap, replacement of thread seal tape/cotton thread, removing any blockage from tap or PVC connection pipe, tightning PVC connection pipe etc will be treated as minor / petty repairs. (b) Tap washers, washers for PVC connection pipe, nut/screw, thread seal tape/cotton thread, shellac, solvent cement etc shall be treated as miror items which shall be provided by the contractor as required with out extra cost. Quoted rate shall deemed to be inclusive of same.

Attending complaints such as non functioning of flushing cistern, leakage and other petty repairs including providing and replacing minor items and ensuring proper and trouble free functioning of low/high level flushing cistern complete all as specified and directed by Engineer-in-Charge. Note : (a) Rectificatin of leakage by correcting siphon washers,replacing washers of PVC connection, tightning the handle/knob/nuts/screws, tightning or replaced loosely fitted float or ball, removing, cleaning and refixing of siphon, replacement of thread seal tape/cotton thread, removing any blockage from inlet/out let mouth or from PVC connection pipe, tightning PVC connection pipe, fixing of flush pipe and cone, handle, brackets etc will be treated as minor / petty repairs. (b) Washers for PVC connection pipe, nut/screw, thread seal tape/cotton thread, shellac, solvent cement, M seal etc shall be treated as miror items which shall be provided by the contractor as required with out extra cost. Quoted rate shall deemed to be inclusive of same.

Attending complaints and carrying out Petty/minor repairs to joinery and builders hardwares, such as easing/adjusting of shutters of any type or size, re-fixing of wire mesh, cub board shutters/shelves, easing/adjusting/refixing of hinges, tower bolts, handles, stoppers, sliding bolts / locks, magic eye, hook and eyes, hasp and staples, etc, of any type and size, and ensuring proper and trouble free functioning, including providing and replacing minor items complete all as specified and directed by Engineer-in-Charge. Note:- (a) Easing/adjusting of shutters and builders hardwares, tightning the handle/knob/nuts/screws, oiling/greasing of builders hardwares etc will be treated as minor / petty repairs. (b) Screws, nails, adhesives etc shall be treated as miror items which shall be provided by the contractor as required with out extra cost. Quoted rate shall be deemed to be inclusive of same.

M&L repairs to cement concrete floor, plinth etc and like using PCC 1:2:4 Type B0 and and finishing the surface to match existing incl preparing the patch surface by cutting out to nearest regular shape, removing loose particles, and cleaning the surface, applying neat cement slurry as required, making good, finishing, work in patches area n exc 0.50 Sqm each patch, depth up to 75mm, and removal of rubbish off the premises complete all as specified and as directed. Note:- (a) Necessary form work, Curing for specified period and leaving the site neat and clean shall deemed to be included in quoted rate

M&L petty repairs to ceramic tiles on floor, by providing and fixing tiles matching existing floor finish, including 15mm thk screed bed CM 1:4 incl neat cement slurry as required, in patches area n exc 1.00 Sqm each patch incl preparing surface by cutting out damaged tiles and screed, removing looose particles, cleaning the surface, and removal of rubbish off the premises complete all as specified and as directed.

S&F In repairs for removal of old PVC/cast iron floor trap incl wall crossing pipe and fixed with new outlet of any size PVC (SWR) floor trap with stainless steel grating and new wall crossing and filling with PCC 1:2:4 with water proofing compound including matching with existed tile and joining with outer pipe line with solvent all as specified and directed by Engg in Charge.

M&L Petty repair of false ceiling by removing of gypsum board and snap grid and fixing 6mm dia hanger and refixing the gypsum boards in the same position after carrying out required repairs to damaged wires and snap grid complete all as specified and as directed

M&L Petty repair of cascade type WC flushing cistern by replacing existing float valve and discharge valve including minor adjustments and servicing of existing make complete all as specified and as directed.

M&L Petty repair of urinal sensor, repair / replacement of Battery holder for sensor urinal /Automatic Valve/PGB Assembly or any parts including replacement of defective parts of urinal sensor and batteries of existing make complete all as specified and as directed.

S&F 32 mm dia PVC waste pipe of length minimum 1.2 meter with cup head for Wash Hand Basin as in repair complete all as specified and as directed.

S&F in repairs stainless steel sink with draining board made out of 1.0mm thick sheet for kitchen with plug , washers waste pipe, cast iron cantilever brackets connecting union over all size 915X460mm with bowl size 410X330X160mm all as specified .

S&F in repair 15mm bore Pillar taps, in repair cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed. Make : Prayag Cat No 6402 or equivalent in approved list of makes

S&F in repairs CP tubular towal rail 20mm dia , 500mm long all as specified Make : Prayag Cat No BA-30 or equivalent in approved list .

S&F in repair for CP towel ring round with flang complete all as specified and directed. Make : Prayag Cat No BA-31 or equivalent in approved list

S&F in repair 100mm to150mm dia SS grating doom with or without hole for waste pipe complete all as specified and directed.

S&F peg set of 6 pin, hooks & rail of stainless steel and fixed with screws complete all as specified and directed.

S & F in repairs Stainless steel Soap dish fixed with screws complete all as specified. Make : Prayag Cat No BA-45 or equivalent in approved list

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 6cm wide with chromium plated bracket guard and railing 50cm long incl aluminium alloy bracket and guard rail Make : Prayag Cat No BEA-47 or equivalent in approved list

S&F in repair corner shelf with 5.5 mm thick sheet glass and SS railing of approved quality fixed with brass screw complete all as specified and directed Make : Prayag Cat No BEA-46 or equivalent in approved list

S & F in repair Vitreous china wash down water closet pan (EWC), any color, pedestal pattern fixed complete all as specified and directed by Engr-in-charge.

S&F in repair Waste fittings, brass, chromium plated 40mm dia for sinks, with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed waste coupling for sink

S&F in repairs white glazed vitreous china WHB flat back size 550x400 mm including CI bracket incl PVC waste pipe 40mm bore 90cm long with cup, spring type and 32mm brass chromium plated waste fitting, complete all as specified .

S & F in repairs Plastic seat and cover, any color closed pattern with flat bottom & cover and mild steel chromium plated or aluminium hinges, etc including fixing bolts complete.

S&F in repair vitreous china squatting pan ‘Orissa pattern’ size 580x440mm white with integral foot rest including connection to trap, and flushing pipe, anti-syphonage pipe, etc and including cement concrete bedding complete all as specified and directed.

S & F in repair PVC valveless, syphonic action type, flushing cistern, low level, 10 ltr capacity any color, with inlet ball valve, float and handle including brackets and all connections, ISI marked .

S & F in repairs PVC connection 15mm bore 45cm long with complete all as specified and directed.

S & F in repairs PVC connection 15mm bore 60cm long with complete all as specified and directed.

S & F in repair Vitreous China urinals, half stall type complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; with PTMT Urinal spreader, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

S&F in repairs Chinaware partition for urinal of size 310x700mm all as specified.

S&F in repairs Push tap high pressure suitable for urinals complete all as specified and directed.

S&F in repairs CP urinal spreader for 15 mm bore fixed with urinal including CP pipe.

S & F in repair vitreous china table top WHB,, size 640 x 400 x 120mm excluding taps, waste, chain and plug and procelin stopper complete all as specified and directed (Make : Jaquar or equivalent from the list of makes)

S & F Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed in repair

S & F in repair vitreous china wash down water closet pan single piece (pedestal pattern) size 365 x 655 x 760mm UF soft close seat cover fixing accessaries set and accessaries set cistern fittings and S trap 220mm complete all as specified and directed (Make Jaquar or equilent)

S & F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed

S&F in repair for 40mm dia cupboard knobs fixed with nut, screws and washer of wooden finish brass polished complete all as specified and directed.

S&F in repair magnet catcher to wooden frame work complete all as specified and directed.

S&F in repair for 25 mm curtain rod fancy type anodised aluminium alloy with fancy brackets and knobs complete all as specified and directed.

S&F in repair for 25 mm curtain rod fancy type SS with fancy brackets and knobs complete all as specified and directed.

S & F in repair aluminium floor door stopper with rubber shoe 140mm long complete all as specified and directed.

S&F in repair MS helical door spring 300mm long including roller and roller plate complete all as specified and directed.

S & F in repair 100 mm stainless steel window stay hook fixed in wooden/ steel window complete all as specified and directed.

S & F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box , main body with stainlesss steel cover, governing pivot made of brass other parts made of mild steel heavy duty in repairs complete all as specified and directed.

M&L for adjusting, easing and minor repairs to aluminium doors/windows of any size, pattern and with two/three shutters & and ensuring proper functioning of the windows including changing of pivot,repairs to lock,handle,rubber beadings etc complete all as specified and directed.

M&L for removal and refixing, adjusting, minor repairs to Stainless steel doors of any size, pattern and with ensuring proper functioning of the doors including changing of floor hing, pivot,repairs to lock,handle,rubber beadings etc complete all as specified and directed.

S & F in repairs Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed,Aluminium(Die cast) body complete all as specified and directed.

S & F in repairs Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed,Aluminium(Die cast) body complete all as specified and directed.

S & F in repair 150mm long Aluminium anodised, barrel tower bolts of extruded section and fixed.

S & F in repair 125mm long Aluminium anodised, barrel tower bolts of extruded section and fixed.

S & F in repair 100mm long Aluminium anodised, barrel tower bolts of extruded section and fixed.

S & F in repair 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S & F in repairs 100mm long Butt hinges, medium weight cold rolled mild steel, and fixed complete all as specified and directed.

S & F in repairs 125mm long Aluminium handles, cast type, anodised complete all as specified and directed.

S & F in repairs 150mm long Aluminium handles, cast type, anodised complete all as specified and directed.

S & F in repairs 300mm long Stainless steel handles, for Toughned doors complete all as specified and directed.

S & F in repair stainless steel 4 lever Mortice lock,vertical type, size 100 mm complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in sub base of floor complete all as specified and directed

M&L for 75mm thick PCC (1:3:6) type C-2 (Using 20mm graded crushed stone aggregate) as in plinth protection /hardstanding , laid in panels, finished the top surfaces even and fair without using extra cement complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M&L for 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded crushed stone aggregate) as in sub base of floor complete all as specified and directed

M & L for Glazed ceramic tiles in vertical surface exc 0.06 sqm but not exc 0.36 Sqm Such as skirting or dados laid over cement mortar backing coat set and jointed with neat cement slurry and pointed with epoxy joint filling including backing coat in CM 1:4, 10mm thick for fixing tiles as in skirting/dado all as specified and directed Note: Quoted rate shall be inclusive of backing coat and epoxy filling shall be measured and paid seperately

M&L for Non skid ceramic tile of size exc 0.08 sqm but not exc 0.36 Sqm in floor over and including cement screed 15 mm thick in CM 1:4 set and jointed in neat cement slurry and pointed with epoxy joint filling complete all as specified and directed. Note: Quoted rate shall be inclusive of screed bed and epoxy filling shall be measured and paid seperately

M&L for Non skid ceramic tile of size exc 0.09 sqm but not exc 0.36 Sqm as in skirting over and including cement backing coat 10mm thick in CM 1:4 etc set and jointed in neat cement slurry and pointed with epoxy joint filling complete all as specified and directed. Note: Quoted rate shall be inclusive of backing coat and epoxy filling shall be measured and paid seperately

M&L for vitrified tiles of size exc 0.15 sqm but not exc 1.00 Sqm in floors with approved pattern over and including cement screed 15 mm thick in CM 1:4 set and jointed in neat cement slurry and pointed with epoxy joint filling complete all as specified and directed. Note: Quoted rate shall be inclusive of screed bed and epoxy filling shall be measured and paid seperately

M&L for Vitrified tiles of size exc 0.15 sqm but not exc 1.00 Sqm as in skirting over and including cement backing coat 10mm thick in CM 1:4 set and jointed in neat cement slurry and pointed with epoxy joint filling complete all as specified and directed. Note: Quoted rate shall be inclusive of backing coat and epoxy filling shall be measured and paid seperately

M&L for epoxy tile joint filling on floor and walls all as per the manufacturers instructions complete all as specified and directed.

M & L for chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick set in neat cement slurry with grey cement and pigments laid over and including 20 mm thick screed bed in CM 1;6 complete all as specified and directed.

M&L for Providing and laying in repairs 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M&L for Providing cement concrete Type B1 1:2:4 (using 20mm aggreagates) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, all as specified and directed.(Rate shall be inclusive of use of formwork (straight or curved).)

M&L for water proofing for sunken slabs including all materials as per the stages described below, complete all as specified and as directed. (a)Remove all dust, oil, dirt, laitance and other contaminants, loose particles from concrete surface . (b) Chamfering the floor wall junctions with cement mortar 1:4 admixed with NitoBond SBr or equivalnt @ 1 litre per 50 Kg bag of cement. (c) Annular space of out let/spout pipes shall be packed and sealed using Conbextra GP2 or equivalent mixed water and filling as per manufacturers specifications. (d) Carrying out ponding for minimum of 48 hours (e) Injection grouting of all leaking spot and honey combs with cementious pressure grouting with 40psi pump using Cebex 100 or equivalent @225 gms mixed to 50 Kg bag of cement incl joints packing using polymer modified mortar. (f) Providing and applying water proof coating using fosroc Nitoproof 600 PF or equivalent, over dry surfaces to achieve 1.5mm thick with 02 coats with interval period of 6 hours over the surface using spray/ squngee/ roller/ brush. Water proofing coating shall have the elongation of 500-700% (ASTM D412-90), tear resistance of 21kN/m (ATMD624-00) and tensile strength of >1.9 N/mm2. Termination to be done on wall extending the coating to min 300mm height above the finished floor level as per vendor recommendation. Laying 200gsm non-woven geo textile membrane over Nitoproof 600PF coating with overlap sealed complete all as specified and directed by the Engineer-in- Charge

M&L for 50mm thick PCC (1:2:4) type B1 (Using 20mm graded stone aggregate) for sub base of sunken portion complete all as specified

M&L for PCC type E2 1:5:10(using 40mm graded stone aggregate) in sunken floor of toilet/bathroom finished fair and even complete all as specified

Demolition of stone slabs/tiles of any description or thickness laid and bedded in any motar complete all as specified and directed.

S & F 18 to 20mm thick granite stone slab over and including cement screed 20mm thick in CM 1:4 as in window cills, steps, jambs, platforms, slab etc complete all as specified and directed .

S&F 18-20mm thick Granite (of any type) slabs machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including backing coat 10mm thick on fair faces of brick work or concrete surfaces in CM 1:3 complete all as specified and directed by Engineer-in-charge

M & L for Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 15mm thick screed bed in CM 1:6 complete all as specified.

M&L for machine cut pre polished Kota stone slab 18-20 mm thick (single piece) as in risers to steps, skiting/dado, pillars, window cills and the like, laid over and including 10mm thick rendering in cement mortar 1:3, set & jointed with grey cement slurry and pointed in white cement mixed with pigment to match the shade of the slab including cutting, rubbing and polishing complete all as specified and directed by Engr-in-Charge.

M& L for grinding of existing terrazo or kota stone flooring by carborundum stone of 320 to 400 grit size. After grinding the surface shall be washed clean and grouted with neat cement grout of cream like consistency using the same coloured cement as in the original mix. After grinding the surface shall again be washed clean and rubbed hard with felt and slightly moistened oxalic acid powder, at the rate of 5 gm of oxalic acid powder for one sq m of floor surface. After completion of grinding work the wax-polish shall be sparingly applied with soft linen on the clean and dry surface. Then the polishing machine fitted with bobs shall be run over it. Clean saw-dust shall then be spread over the floor and polishing machine again applied, mopping up surplus wax and leaving glossy surface. Care shall be taken that the floor is not let slippery complete all as specified and directed by Engr-in-Charge.

Demolition of brick work/ block work/ stone /boulders masonry built in cement mortar including all quoins, arches , pillars etc complete all as specified and directed

M&L for pre cast cement concrete block masonry 1;3;6 Type C1 with solid blocks exe 10 cm in width and setting in CM 1:6 complete all as specified and directed

M&L for providing precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed), type C1 1:3:6 (20mm graded aggreagate) setting in cement mortar 1:4,complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water any description, etc Note for item no 87 and 89: work to be executed in any location/floor(multistory buildings) including in shaft portion, Quoted rates shall be inclusive for scaffoling / staging upto any height required at site and also for working in foul conditions

M&L for rendering 10mm thick mixed with liquid water proofing compound on fair faces of brick work or concrete surfaces, on brick work or concrete wall surfaces in 1:6 cement mortar, finished even & smooth without using extra cement all as specified and directed

M&L for rendering 15mm thick mixed with liquid water proofing compound on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed by Engr-in-Charge. (WPC shall be paid seperately)

M&L for rendering 5mm thick mixed with liquid water proofing compound on fair faces of brick work or concrete surfaces on ceiling surfaces in 1:3 cement mortar finished even &smooth without using extra cement all as specified and directed

Supply only liquid water proofing compound complete all as specified and directed by Engr-in-Charge.

M&L for preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of primer with and including provision of 1.5mm thick wall putty complete all as specified and as directed.

M&L for preparation of newly plastered wall surfaces and application of two coats of cement based paint over a coat of primer all as specified and directed

M&L for preparation of newly plastered ceiling surfaces and application of two coats of OBD over a coat of primer all as specified and directed

M&L for preparation of newly plastered ceiling surfaces and application of three coats of white wash all as specified and directed

M&L for preparation of old plastered surfaces of walls including washing, rubbing down surfaces on walls including filling of nail holes/disturbed surfaces by cementitious wall care putty and applying one coat of oil bound distemper at any height up to 9th floor , complete all as specified .

M&L for preparation of old plastered ceiling surfaces and application of one coat of OBD all as specified and directed

M&L for Preparation of existing treated surfaces and applying one coat of exterior anti fungal acrylic emulsion paint at any storey, including provn and removal after use, of necessary scaffolding, complete all all as specified and as directed by Engineer In Charge.

M&L for preparing old treated steel surfaces of any description exc 10 cm width or girth and applying one coat of synthetic enamel paint all as specified

M&L for preparing old treated surface of steel of any description n.exc 10 cm width or girth and applying one coat of synthetic enamel paint all as specified

M&L for preparing old treated surface of wood or wood based material of any description exc 10 cm width or girth and applying one coat of synthetic enamel paint all as specified

Dismantling wrought iron or mild steel work of any description not otherwise provided for

M & L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

M&L MS Framed work confirming to Fe 410 -W (Gde- E- 250) quality- A as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing complete

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240.

M&L for preparation of new steel Surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of anti corrosive paint over two coats coat of Epoxy primer, on steel surfaces complete all as specified and directed.

Taking down chowkats n.exc 1.5 Sqm but with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) exc 1.5 Sqm but n.exc 4 Sqm each complete all as specified and directed.

Taking down shutters of any description n.exc 1 Sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but n.exc 2 Sqm each complete all as specified and directed.

M&L for 2nd class Hw Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed

M&L for 2nd class HW 35mm thick Plain framed, panelled factory made shutters (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for 2nd class HW 35mm Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (B); supplied and fitted to chowkats complete all as specified and directed.

S&F 35mm thick Flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

M&L for 18-19 mm thick pre laminated particle board exterior grade one side with decorative choice lamination & other side balancing white lamination fixed with nails and screws for C.B in repair complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30 mm thick with particle board core (stiles),with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm Plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed

S&F Continuous ( Piano) hinges width of flap 30 mm fixed in repair complete all as specified and as directed

S &F in repair stainless steel handles 100mm long of approved quality all as specified and directed.

S &F in repair stainless steel self closing type hinges for kitchen cabinet of approved quality all as specified and directed.

M&L for Antitermite post costruction treatment at all points of contact of wood work by chemical emulsion @0.5litre/ hole by drilling 6mm dia holes at a down ward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed

M&L for preparation of new wooden Surfaces of any description, not otherwise described, over 10cm width or girth and applying 2 coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads

S&F 4mm thick Sheet glass one side frosted, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and as directed by Engineer-in-Charge.

S&F 4mm thick plain Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

S&F 4mm thick plain Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

S&F Toughned glass 10 mm thick as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required complete all as specified and as directed

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box , main body with stainlesss , steel ocver, governing picot made of brass other parts made of mild steel heavy duty complete all as specified and as directed

S & F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed

S&F powder coated anodised aluminium frame for doors, windows, ventilator with one or more rebates including joining cleat for fixing etc. complete (Sliding type/Side hung type) complete all as specified and as directed

S& F powder coated Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed

S& F powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed

S&F powder coated aluminium door , partitionining shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

S&F 5-6mm thick Aluminum composite panel of suitable/matching colour, fixed with screws/any suitable arrangement to Aluminum frame work including beading including dismantling existing boarding (ply/partice board) complete all as specified and directed.

S&F in repairs, 9mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to frame work complete all as specified and directed.

S&F in repairs, 16-18mm MDF DWR Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including beading /matching laminates to exposed edges of board complete all as specified and directed.

S&F in repairs 12-18mm thick rubwood as in CB etc cut to shape as specified and fixed with screws complete all as specified and as directed

S&F Aluminum powder coated fixed type windows including suitable nylon beading channel gasket etc complete with following specification :- Frame :- 60mmx40mmx1.80mm Panel :- 4mm thick ACP sheet / 5mm thick tinted/frosted glass of approved colour and design

S & F in repairs 4mm thick coloured/wooden grain aluminium composite panel cladding to PVC rainwater pipe /RCC column etc… and including aluminium framing work complete all as specified and directed Note : The quoted rate shall be inclusive of aluminium frame work

Repair to rolling shutter without taking down any size and including greasing, oiling to all connected accessories and fuctioning trouble free complete all as specified and directed.

Repair to rolling shutter including taking down any size and including greasing, oiling to all connected accessories and make functional to operate gear box and all other accesories trouble free complete all as specified and directed.

M & L for for PCC 1:2:4 type B-1,using 20mm graded stone aggregate for fixing hold fast including necessary form work complete all as specified and directed

S&F MS work as in hold fast and similar small articles conforming to Fe-290, Gde E-165 complete all as specified and directed.

S & F 100mm stainless steel butt hinges, medium wt complete all as specified and as directed.

S & F 75mm stainless steel butt hinges, medium wt complete all as specified and as directed.

S & F 150mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S & F 100mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S & F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S & F 125mm long Aluminium handles, cast type, anodised complete all as specified and as directed.

S & F 150mm long Aluminium handles, cast type, anodised complete all as specified and as directed.

Dismantling Single layer Mangalore pattern or similar tiles in roofing complete all as specified and as directed.

Dismantling Battens for tiles, shingles etc, of any size including tilting fillets spaced n.exc 15 cm

Dismantling fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section,unframed work

M & L for Roof tiles, Mangalore pattern, interlocking at side joints, laid dry complete all as specified and directed

Fixing only Roof tiles, Mangalore pattern, interlocking at side joints, laid dry complete all as specified and directed Note : Serviceable MP tile obtained under item No 153 shall be reused

M&L for Ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in cement mortar 1:6 complete all as specified and directed

M&L for 2nd class HW Plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads exc 13 sqcm & n exc 25 sqcm complete all as specified and directed

M&L for 2nd class HW Clean sawn battens at 15 cm centres,exc 5 & n.exc 15 sqcm complete all as specified and directed

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed

M&L for 2nd class HW Weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified and directed

M&L for Preparing the surfaces of battens, any size and spacing, prepared and treated all over (measured overall on one side only, spaces not deducted) with 2 coats of creosote oil complete all as specified and directed

M&L for Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with 2 coats of creosote oil complete all as specified and directed

Dismantling timber scantiling 40 Sqcm and over in section unframed work in any position

M&L for 2nd class hard wood in scantling clean sawn fixed as in purlins, rafters, etc in roof complete all as specified and directed

Dismantling plain or corrugated steel sheeting, any guage, thickness incl Nainital or similar pattern roof covering complete all as specified and directed

S & F 0.63 mm thick galvanised corrugated mild steel sheeting with two corrugation side lap, fixed with L-hook or cranked bolts complete all as specified and directed

S&F for pre-painted galvalume zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws complete all as specified and directed

S&F for pre-painted galvalume zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed

S&F 1mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings & similar works (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed

S&F Plain Aluminium sheeting 0.71mm thick, Alloy 31000H4 in ridge, hips, valley gutter, drip and straight flashings complete all as specified and directed

M & L for continuous welding in repairs exc 2.5cm but n exc 5 cm in length Thickness of Metal to be welded not exc 6mm complerte all as specified and directed by Engineer-in-Charge.

Demolition of reinforced cement concrete in any description and in any position not otherwise specifically provided for (reinforcement cut to facilitate demolition) all as specified and as directed by Engineer in Charge.

M&L RCC (1:2:4) type B-1 (Using 20mm graded crushed stone aggregate) as in slabs, shelves supported on walls, beams and columns in floor or roof including balconies, canopies, deck slabs or in Chajja/facia projection and the like complete all as specified and directed

M&L mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick for rough finished flat surfaces (Horizontal or sloping) complete all as specified and directed by Engr-in-Charge.

S&F in repair precast cement concrete type B0 1:2:4 louvres and jallies, 45mm thick (mea sured solid), including all moulding complete all as specified and directed

M & L for RCC surface shall be made dry,clean, even and checked for soundness. Removal of oil,dirt,laitance and other contaminants by manually and surface shall be fairly smooth finish. Injection grouting of construction joints and honey combs if any with cementitious pressure grouting with 40 psi pump using cebex 100 or equivalent make in approved manufacturer's list @ 225 gms mixed to 50kg bag of cement including joints packing using polymer modified mortar. Providing and applying pitch free polyethene water proof coating using Fosroc Nitoproof 600PF or equivalent, by specialised agent/manufacturer authorised applicator over dry surface at 1.5mm thick in 2 coats with interval period of 6 hours over a substrate at coverage rate of 2Kg/Sqm using spray/squeege/ roller/ brush. Water proofing coating shall have the elongation of 200% (ASTM D412-90, Tear resistance of >7N (ASTM D 624-00), and tensile strength of 1.5N/mm2 (ASTM D412-90) and it should have a solid content of 80-85% incl laying 200gsm non woven geotextile membrane over Nitoproof 600 coating with overlap sealed before providing screed concrete. Sprinkle fine sand aggregate straight after the application of Nitoproof 600PF to get mechanical key for the protective screed of 15mm thick in CM 1:3.

M&L for Micro concreting in RCC coloumns, beamsor soffit of slab including chemicals, reinforcement, form work average thickness not exceeding 50MM as per the following stages:- (I) Remove the damaged concrete portions completely till the reinforcement is exposed from the member carefully with mechanical arrangements and hand chiseling and clean the dust particles. (If the dia of existing reinforcement has reduced by more than 1/3 of the original dia, additional reinforcement has to be provided and fixed in position as directed by Engineer In Charge. Additional reinforcement will be measured and paid separately ) (ii) Clean the reinforcement and apply Nitrozinc primer manufactured by M/S Fosroc chemicals or equivalent from the list of makes (iii) Applying the bonding agent by using NITO BOND EP or equivalent (iv) Providing leakproof shuttering system for the jacket portion of the members and applying micro concrete with Rendroc RG manufactured by M/S Fosroc chemicals or equivalent( compressive strength of Micro concrete should be 50 N/mm2)

M & L for Repairs to expansion joint with following specifications: a) Demolition and removal of masonary (stone/brick/PCC block or any floor finishes if any on joints in floor slabs) over the expansion joints & necessary chipping with machine, electrical chipper tools & removing debris from site and disposal at a location as directed by Engr-In-Charge. b) Open the expansion joint by chipping the loose portions by the surface, straightening the edges of the expansion joint using FOSROC Renderoc-s2 or equivalent make of pidilite, SIKA, STC Dr fixit, two part structural grade reinstatement mortar or equivalent including preparation of surface complete all as per manufacturer's instructions. c) After strengthening the edges of expansion joint, the same is filled with Hydrocell XL or equivalent make of pidilite, Sika, STC,of required thickness, and the polythelene backer rod of required dia to be fixed in expansion joint and then filled with concrete of size 40mmx20mm with FOSROC Thioflex 600 two part polysulphide sealant or equivalent material.

d) Providing & fixing a expoband one a hypalon membrane system which is designated to be bonded over movement joints instructures to prevent the passage of water. The Hypalon membrane is bonded in position using Nitobond PC, two part epoxy adhesive or equivalent make of Pidilite, SIKA,STC complete all as per manufacturer's instructions. e) Providing & applying bituminous water based primer on the prepared surface and when the surface is tacky with self adhesive SBS membranes by using FOSROC Proofex GP or equivalent make of pidilite, Sika, STC are installed and firmly pasted it on the existing membrane joints laid in dry condition with approximate 80mm overlap of edges complete

M&L in repair for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including frame work. cover fillets etc complete all as specified.

Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions including necessary scaffolding and shuttering complete as directed as specified and directed

S&F Aluminum snap grid false ceiling with grid 605x605mm size including hangers 6 mm dia GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flats 40 x 3 mm size 60 mm long & expansion hold fastners 12.5 mm dia 40 mm long complete all as specified

M&L 4mm thick Non asbesto fiber cement building board fixed or laid /inserted to timber/GI/Aluminium Frame work with screw in ceiling complete all as specified and directed.

M & L Welded steel wire fabric weight n exc 4 kg/sqm fixed to steel members complete all as specified

S&F in repairs Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors , 75mm bore pipe complete all as specified and directed.

S&F in repairs Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls, 75mm bore pipe complete all as specified and directed.

S&F repairs Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors , 100mm bore pipe complete all as specified and directed.

S&F repairs Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls, 100mm bore pipe complete all as specified and directed.

S&F in repairs PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with clamps of height up to 15 m, 75mm bore pipe

S&F in repairs PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with clamps of height up to 15 m, 110mm bore pipe

S&F in repairs Cast iron vent cowl slotted, 75mm complete all as specified and directed

S&F in repairs CI Bends (any radius), diminishing pieces or tapers (larger bore measured) with access door, 100mm bore complete all as specified and directed

S&F in repairs CI Bends (any radius), diminishing pieces or tapers (larger bore measured) with access door, 80mm bore complete all as specified and directed

S&F in repairs CI Bends (any radius), diminishing pieces or tapers (larger bore measured), 100mm bore complete all as specified and directed

S&F in repairs CI Bends (any radius), diminishing pieces or tapers (larger bore measured) , 80mm bore complete all as specified and directed

S&F in repairs CI Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches , 100mm bore complete all as specified and directed

S&F in repairs CI Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches , 75mm bore complete all as specified and directed

S&F in repairs CI Branch pieces, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches , 100mm bore complete all as specified and directed

S&F in repairs CI Branch pieces, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches , 75mm bore complete all as specified and directed

S&F in repairs PVC (SWR) bends any radius 75mm bore complete all as specified and directed

S&F in repairs PVC (SWR) bends any radius 110mm bore complete all as specified and directed

S & F in repairs 200 mm dia of half round or 180 mm width rectangular UPVC SWR ready made eaves gutter of pressure rating 6 Kg/cm2 of approved make including necessary fitting like bend WC/MS Clips etc complete all as specified and directed

S & F in repairs 150MM dia of UPVC (SWR) pipe single socketed in any length with rubber joints including necessary fitting like bend WC/MS clips etc fixed on walls complete all as specified and directed

S&F in repairs stainless steel of grade 304 Grab Bar Rails(for supporting WC) with/without Anti-Slip Nylon Grip & Floor Support- 24 inches of lengths 600mm vertical / horizontal with curving edges, fixed to walls over tiling Wall Mounted Flip up , Bathroom Safety Bar for the elderly, pregnant women and handicap including drilling and fixing and making good wall etc complete all as specified and directed

S&F in repairs stainless steel of grade 304 Grab Bar Rails (for supporting urinals) with Anti-Slip Nylon Grip 600mm horizontal with curving edges, fixed to walls over tiling Wall Mounted of make REHAMO GRABSY AWMFU-600 or equivalent, including drilling and fixing and making good wall etc complete all as specified and directed

S&F in repairs Solar control film 25 micron reflective type/frosted type sticked to glass panes as per instructions of manufacturers complete all as specified and directed

S&F in repair SS door (Single door) fabricated by SS 304 grade with (50mm thick door) puff filed door of Size as required with door frame 1.2mm thick (18 gauge) with SS door shutter SS304 grade hinges 04 in nos, Door closer, Mortice lock set 1no. Euro cylinder 1 no, D handle SS 304 19mm dia 254 mm 2 nos, door bottom Seal with all other connceted accessories etc complete all as specified and directed.

S&F in repair 2mm thickness Lead sheet fixed to the doors/windows etc, with necessary screws as per manufacture instruction all as specified and directed.

S&F in repairs PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, 75mm bore pipe complete all as specified and directed.

S&F in repairs PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, 110mm bore pipe complete all as specified and directed.

S & F in repairs 4mm thick coloured/wooden grain aluminium composite panel (approved by the Engineer in Charge) fixed to aluminium or timber frame complete all as specified and directed

S&F in repair 6 mm thick Polycarbonate translucent corrugated/plane sheeting fixed with coach screw and washer in roof, wall etc. complete all as specified and directed.

M/s T.P SHAJI (BID ID -3369168)

Suprisons (BID ID -3380576)

JKM CONSTRUCTIONS (BID ID -3380651)