Interior work for the Setting up of SPMU Office Space in LAPoshe, Trivandrum for KERA Project Composite work

Amount

Appendix A- Setting of new SPMU Unit in Lapoche Trivandrum

12.45.3 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum moisture resistant board

9.105.1 Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. 75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG),plaster board conforming to IS : 2095 : (part 3) 1996 (Board with BIS Certification marks)

SLIDING GLASS DOOR FOR CABINS (Size :900x 2100mm ) :Providing & fixing of 12mm thick toughened glass door with all necessary hardware's including guide channel,Rollers of approced make etc complete. Including all the fixturres having ISI standard specification and as per instruction of engineer in charge.

21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of standard specifications of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock and stopper etc to be paid separately)

WOODEN FRAMED GLASS DOOR FOR MAIN CABIN (Size :1000x 2100mm ) :Providing & fixing first class teak wooden framed of 12mm toughened glass door with all necessary hardware's such as Floor Springs Top & Bottom Patch , Handles (300mm) & Lock etc as per approved make and standards etc complete as per instruction of engineer in charge.

MAIN ENTRANCE GLASS DOOR Glass Door (Size :2000x 2100mm ) :Providing & fixing Two leaves of 12mm thick toughened glass door in with sensor opening with all necessary hardware's such as Floor Springs (ebco, aoric or equvalent), Top & Bottom Patch , Handles(900mm) & Lock,necessary fixures as per approved design and standards etc complete as per the direction if the Engineer in charge. .

Fixed glass partitions :Providing & fixing of 12mm thick toughened glass partition with all necessary hardware's such as , Top & Bottom Patch with all necessary hardwares ,as per standrads and as per the direction of the Engineer in charge. etc complete .

Frosted Film : providing and fixing of approved shade of frosted film as per the design .The Film will be applied with all necessary surface preparation and finishes etc complete as per instruction of engineer in charge.

13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

13.83.2 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile including applying additional coats wherever required to achieve even shade and colour. Two coats

WALL PANELING : providing and fixing 12 mm wpc laminated flueted paneling fixing with sylicone (Rate is inclusive of all charges of glue, transportation etc as required inluding all safety precautions for carrying out work as per the direction if the Engineer in charge.

Providing and fixing panelling board made of 12mm Thick 710 grade laminated flueted plywood with approved shade as per the design . as per the direction of the Engineer in charge.

RECEPTION TABLE (Size :3500x 600X1100mm) : Fabrication and installation of L shape reception table of approved size as per the design . The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design . The user end of the table will be at 750mm from the FFL and the visitor end will be 1050mm from the FFL . The unit will be having the provision of 12 mm thick Clear glass fixed towards the unit with the help of approved SS Stud . all necessary hardware's etc. as per standrads ,locking arrangemants ,handles etc complete. as per standard specification and design as per the direction if the Engineer in charge.

3 Seater sofa measuring 2000x850x900 mm, featuring a 1.2 mm foam-laminated Rexine seat and back cover. The seat frame is made from molded plywood with a thickness of 12 mm. The armrests are wrapped in foam and finished with foam-laminated Rexine for enhanced comfort. The foam density is 32, with a cushion thickness of 100 mm for the backrest and 150 mm for the seat, designed in accordance with industry standards to ensure optimal support and durability. The overall design is crafted for a sleek and polished finish as per the direction if the Engineer in charge. .

MINI TABLE (Size:900x 600X400mm ) Fabrication and installation of centre table of approved size as per the design . The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc. as per the direction if the Engineer in charge.

LOW HEIGHT STORAGE (Size:1500x 400X1500mm ) : Fabrication and installation of low height storage of approved size as per the design . The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's of standard make,locking arrangements etc. complete as per the direction of the Engineer in charge.

STORAGE @ SECURITY CABIN (Size:1500x 400X2100mm - : Fabrication and installation of l storage of approved size as per the design . The cabinet will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc. locking arrangements ,hinges,standard make as per the direction if the Engineer in charge. as per standard specification and design etc complete.

ROMAN BLINDS :Providing and fixing roman blinds Vista Leveller Make imported superior polyester base fabric vanes with scotch guard application as per approved sample as per the direction if the Engineer in charge. ,

WORK STATIONS (Size:1220x 550X1100mm ) : Fabrication and installation of workstation table of approved size as per the design . The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design . The user end of the table will be at 750mm from the FFL and the divider end will be 1100mm from the FFL .all necessary hardware's locking arrangements ,hinges etc of approved make etc complete. as per the design and direction 0f the Engineer in charge.

CORNER WORK STATIONS (Size:2825x 550X1100mm ) : Fabrication and installation of workstation table of approved size as per the design . The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design, all necessary hardware's etc. as per standrads ,locking arrangemants ,handles etc complete. as per the direction if the Engineer in charge.

DRAWER CHEST FOR WORKSTATION TABLE (Size:400x 500X720 mm ) : Fabrication and installation of drawer chest for workstation table of approved size as per the design. It will be made of 16mm Thick 710 grade Plywood with approved shade of laminate as per the design. all necessary hardware's etc. as required, as per standrads like SS handles, magnetic stopper ,SS auto close hinges.,locking arrangemants ,handles etc complete. as per the direction if the Engineer in charge.

EXECUTIVE TABLE (Size:1500x 750X750mm ) : Fabrication and installation of table of approved size as per the design with one sided cup board. The Table will be made of 16mm Thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc, as per standrads ,locking arrangemants ,handles etc complete as per instruction of engineer in charge.

EXECUTIVE TABLE (Size:1500x 600X750mm ) : Fabrication and installation of table of approved size as per the design with one sided cup board. The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design all necessary hardware's etc. As per standrads ,locking arrangemants ,handles etc complete, as per instruction of engineer in charge.

EXECUTIVE TABLE (Size:1300x 900X750mm ) : Fabrication and installation of table of approved size as per the design with one sided cup board. The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc.as per standrads ,locking arrangemants ,handles etc complete, as per instruction of engineer in charge.

EXECUTIVE TABLE (Size:1800x 750X750mm ) : Fabrication and installation of table of approved size as per the design with one sided cup board . The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc.as per standrads ,locking arrangemants ,handles etc complete, as per instruction of engineer in charge.

SIDE CREDENZA (Size:1200x 400X730mm ) : Fabrication and installation of side credenza of approved size as per the design . The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc. as required, as per standrads like SS handkes, magnetic stopper ,SS auto close hinges, locking arrangemants ,handles etc complete per instruction of engineer in charge.

SIDE CREDENZA (Size:1000x 400X730mm ) : Fabrication and installation of side credenza of approved size as per the design . The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc. as required, as per standrads like SS handkes, magnetic stopper ,SS auto close hinges, locking arrangemants ,handles etc complete per instruction of engineer in charge.

SIDE CREDENZA (Size:900x 400X730mm ) : Fabrication and installation of side credenza of approved size as per the design . The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc. as required, as per standrads like SS handkes, magnetic stopper ,SS auto close hinges, locking arrangemants ,handles etc complete per instruction of engineer in charge.

SIDE CREDENZA (Size:750x 400X730 mm ) : Fabrication and installation of side credenza of approved size as per the design . The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc. as required, as per standrads like SS handkes, magnetic stopper ,SS auto close hinges, locking arrangemants ,handles etc complete per instruction of engineer in charge.

Low height storage (Size:2000x 400X730 mm ) : Fabrication and installation of low height storage of approved size as per the design . The Table will be made of 16mm Thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc, as per standrads ,locking arrangemants ,handles etc complete as per instruction of engineer in charge.

EXECUTIVE TABLE (Size:3000x 900X750mm) : Fabrication and installation of table of approved size as per the design with side cupboards . The Table will be made of 16mm Thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc. as per standrads ,locking arrangemants ,handles etc complete as per instruction of engineer in charge.

2 SEATER SOFA (Size1500x850x900): featuring a 1.5 mm foam-laminated Rexine seat and back cover. The seat frame is made from molded plywood with a thickness of 12 mm. The armrests are wrapped in foam and finished with foam-laminated Rexine for enhanced comfort. The foam density is 32, with a cushion thickness of 100 mm for the backrest and 150 mm for the seat, designed in accordance with industry standards to ensure optimal support and durability. The overall design is crafted for a sleek and polished finish as per instruction of engineer in charge.

TV CABINET(Size:2000x 350X300 mm ) : Fabrication and installation of tv cabinet of approved size as per the design . The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design , all necessary hardware's etc, as per standrads ,locking arrangemants ,handles etc complete as per instruction of engineer in charge.

SHOW CASE (Size:4750x 300X2100mm - : Fabrication and installation of show case and storage of approved size as per the design . It will be made of 12mm thick 710 grade Plywood with approved premium quality graphic designed laminate (for the rear side) and plain laminated plywood (Side rack) as per the design .with lighting arragemnets using LED fittings etc, locking arrangements ,hinges,standerd make as per the design and direction if the Engineer in charge.etc complete.

EXECUTIVE TABLE (Size:2400x 1000X750mm ) : Fabrication and installation of table of approved size as per the design with one side cupboard . The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc. as per standrads ,locking arrangemants ,handles etc complete as per instruction of engineer in charge.

STORAGE(Size:3600x 500X2400mm ) : Fabrication and installation of low height storage of approved size as per the design . The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc. as per standrads ,locking arrangemants ,handles etc complete as per instruction of engineer in charge.

DISCUSSION TABLE (Size:1500x 750X 750mm ) : Fabrication and installation of discussion table of approved size as per the design . The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc as per standrads, complete as per instruction of engineer in charge.

MINI CONFERENCE TABLE (Size:3300x 1150X 750mm ) : Fabrication and installation of conference table of approved size as per the design including bottom shelf at a depth of 20 cm below the top platform for storage of documents. The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc complete, as per instruction of engineer in charge.

CONFERENCE TABLE (Size:7200x 1000X 750mm ) : Fabrication and installation of conference table of approved size as per the design including bottom shelf at a depth of 20 cm below the top platform for storage of documents . The Table will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc. as per standrads ,locking arrangemants ,handles etc complete as per instruction of engineer in charge.

ACOUSTIC CEILING (Size:10450x 4385 ) : calcium silicate acuostic ceiling made G I sectionig and 12 mm thick calcium silicate perforated borard with 500 gsm sythatic wool for reduse echo as per instruction of engineer in charge.

LOW HEIGHT STORAGE UNIT (Size:2380x 500X 850mm) : Fabrication and installation of low height storage unit of approved size as per the design . The storage will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc. as per standrads ,locking arrangemants ,handles etc complete as per instruction of engineer in charge.

WALL CABINET (Size:1000x 300X 600mm ) : Fabrication and installation of cabinets of approved size as per the design . The cabinets will be made of 16mm thick 710 grade Plywood with approved shade of laminate as per the design .all necessary hardware's etc. as per standrads ,locking arrangemants ,handles etc complete as per instruction of engineer in charge.

FOLDABLE TABLE TOP FOR STAFF DINING (Size:2000x 500) : Fabrication and installation of table top of approved size as per the design . The top will be made of 16mm thick 710 grade Plywood with wooden lipping approved shade of laminate as per the design .all necessary hardware's etc. as per standrads etc complete as per instruction of engineer in charge.

SEMI EXECUTIVE MEDIUM BACK REVOLVING CHAIR Supplying and placing in position Medium Back Chairs with good ergonomic design and lumbar support, Glass filled Nylon Base, Gaslift, Twin Wheel Nylon Castors; Fixed PP Armrest; Back: ABS with Mesh Upholstery, Synchro Tilt Mechanism, Inbuilt Lumbar Support; Seat: PU Moulded Cushion with fire retardant Fabric of approved colour as per directions of Engineer-in-chargeOverall height of chair should be minimum 1000 mm (Warranty period: 5 years and product should be BIFMAA certified) as per instruction of engineer in charge.

SEMI EXECUTIVE MEDIUM BACK REVOLVING CHAIR Providing and supplying of eargonomically designed fabric upholstered high back revolving chair.The seat cushion of the chair should be made up of 50mm thick high density of 45+-2 kg /m3 polyurethane mould and back cushion should be made up of 38mm thick high density 33+-2 kg/m3 the polyurethane foam shall be as per manufacturer's specification.The hardness of foam shall be 20 kg on hampden machine and 25% compression and it should be covered with as per manufracturer's shade card.The arms of the chair should be black.The gas lift mechanism shoud be tested as per standars.The pedestal should be 5 legged injection mouldedin black nylonand fitted with 5 Nos twin wheel castors.The castors of the chair should be glass filled ,twin wheel castors and tested to perform 1 lakh cycles with 225 lbs load . note-The back and base of chair should be supplied with black polypropylene fabric upholstered.Overall height of chair should be minimum 1050 mm (incluseive of maximum adjustment of gas liG mechanism) as per instruction of engineer in charge.

PREMIUM HIGH BACK REVOLVING CHAIR Providing and supplying of eargonomically designed fabric upholstered high back revolving chair.The seat cushion of the chair should be made up of 50mm thick high density of 45+-2 kg /m3 polyurethane mould and back cushion should be made up of 38mm thick high density 33+-2 kg/m3 the polyurethane foam shall be as per manufacturer's specification.The hardness of foam shall be 20 kg on hampden machine and 25% compression and it should be covered with as per manufracturer's shade card.The arms of the chair should be black.The gas lift mechanism shoud be tested as per standars.The pedestal should be 5 legged injection mouldedin black nylonand fitted with 5 Nos twin wheel castors.The castors of the chair should be glass filled ,twin wheel castors and tested to perform 1 lakh cycles with 225 lbs load . note-The back and base of chair should be supplied with black polypropylene fabric upholstered.Overall height of chair should be minimum 1225 mm (incluseive of maximum adjustment of gas liG mechanism) as per instruction of engineer in charge.

SEMI EXECUTIVE VISITORS CHAIR Providing and supplying of fixed base cushion chair for visitors shall be low back chair. The arms of the chairs should be black, The chair shall be supplied with PU moulded seat and back.The under structure should be made of tubular cantilever type MS ERW tube back powder coated The chair shall be supplied with fabric of approved make and shade for seat and back. Note-The back and base of the chair should be supplied with fabric upholstered. overall height of chair- 750 mm as per instruction of engineer in charge.

EXECUTIVE HIGH BACK CHAIRS FOR DEPARTMENT HEADS The seat cushion of the chair should be made up of 50mm thick high density of 45+-2 kg /m3 polyurethane mould and back cushion should be made up of 38mm thick high density 33+-2 kg/m3 the polyurethane foam shall be as per manufacturer's specification.The hardness of foam shall be 20 kg on hampden machine and 25% compression and it should be covered with as per manufracturer's shade card.The arms of the chair should be black.The gas lift mechanism shoud be tested as per standars.The pedestal should be 5 legged injection mouldedin black nylonand fitted with 5 Nos twin wheel castors.The castors of the chair should be glass filled ,twin wheel castors and tested to perform 1 lakh cycles with 225 lbs load . note-The back and base of chair should be supplied with black polypropylene fabric upholstered.Overall height of chair should be minimum 1200 mm (incluseive of maximum adjustment of gas liG mechanism) as per instruction of engineer in charge.

LUXURY RECLINER OFFICE CHAIR WITH SIVEL Providing and supplying of eargonomically designed leatherette seat material high back revolving chair.The seat cushion of the chair should be made up of 50mm thick high density of 45+-2 kg /m3 polyurethane mould and back cushion should be made up of 38mm thick high density 33+-2 kg/m3 the polyurethane foam shall be as per manufacturer's specification.The hardness of foam shall be 20 kg on hampden machine and 25% compression and it should be covered with Beige and Tan Leather, Chrome base..The gas lift mechanism shoud be tested as per standars.The pedestal should be 5 legged injection mouldedin black nylonand fitted with 5 Nos twin wheel castors.The castors of the chair should be glass filled ,twin wheel castors and tested to perform 1 lakh cycles with 225 lbs load .Overall height of chair should be minimum 1350 mm (incluseive of maximum adjustment of gas liG mechanism) as per instruction of engineer in charge.

Supply of round pantry chair with a rubberwood seat pad (400 mm diameter, 17 mm thick) and a stainless steel frame (202 grade, 20 mm), as per the instructions of the engineer in charge

6.13.2 : Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement : 4 coarse sand)

11.53 Providing and fixing Glass mossaic tiles at finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design, fixing in customize design as per direction of Engineer-in-charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-charge.

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

9.121 : Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross- section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminated shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

9.122.2 : Providing and fixing to existing door frames.30 mm thick Fiberglass Reinforced Plastic (F.R.P) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used all filler material throughout the hollow panel, casted monoolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS : 14856, complete as per direction of Engineer-in-charge.

Providing and laying anti-skid ceramic floor tiles (600x600x10 mm) of first quality, conforming to IS: 15622, from an approved make, shade, and pattern. The tiles shall be laid on a 20mm thick cement mortar (1:4 ratio of cement to coarse sand) and jointed with grey cement slurry at a rate of 3.3 kg per sqm. The work includes pointing with epoxy joint filler, along with the cost and conveyance of all materials, labor charges, lead, lift, etc., completed as directed by the Engineer-in-Charge at all levels

Providing and laying I st quality ceramic glazed wall tiles (600x600x10 mm) , conforming to IS: 15622, from an approved make, shade, and pattern. The tiles shall be laid on a 12mm thick cement mortar (1:3 ratio of cement to coarse sand) and jointed with grey cement slurry at a rate of 3.3 kg per sqm. The work includes pointing with epoxy joint filler, along with the cost and conveyance of all materials, labor charges, lead, lift, etc., completed as directed by the Engineer-in-Charge at all levels

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

17.7.3 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

17.32 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid .

17.80 Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitablebrackets all as per manufacturers specification and direction of Engineer-in-charge.

Supplying and fixing approved quality white vitreous china urinal division plate 700 x 340 including cost and conveyance of all material, labour charge, lead, lift, all taxes etc. complete as directed by the Engineer-in-Charge.

17.7.6 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Angle back wash basin size 400 x 400 mm with single 15 mm C.P. brass pillar tap

17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

50.17.1.3 Supplying and fixing CP Towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge

50.17.1.1 Supplying and fixing Stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Providing and fixing 304 garded SS tissue rod holder complete with CP brass screws with concealed fittings arrangement of approved quality. 165 mm long ,60 mm wide a

18.51.1 : Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

18.52.1 : Providing and fixing C.P brass stop cock ( concealed) of standard design and of approved make conforming to IS: 893115 mm nominal bore

Providing and fixing Cleanout with Spigot, with SS 304 Square Frame & Round Frame with Flat Round Cover with Rubber Seal & SS Screw including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer in charge at all levels 110 mm dia

Providing and fixing floor trap of PVC,110 mm outer dia(multi trap) including CP cockroach free floor SS grating with cup etc including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer-in-Charge at all levels

50.18.8.6.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2

50.18.8.8.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2

50.18.8.9.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

Supplying approved make PVC gully trap of size 160 x 110mm and CI grating 150mmx150mm size and light duty C.I cover with frames 300mmx300mm size(inside) the weight of cover to be not less than4.5kg and frame to be not less than2.7kg (CI MH cover and frame as per IS:1726) etc complete as per approved drawing and as directed by Engineer-in- Charge.

19.7.1.1 : Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.33 : Constructing soak pit 1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

50.18.9.21.7 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Vent cowl

50.18.9.22.8 : Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl

18.8.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal outer dia pipes

18.8.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal outer dia pipes

18.17.1 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

50.17.1.5 Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

22.5 : Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 1200x600 mm-matt finish

4.1.2 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:1/2:3 (cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size)

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

Supplying and fixing at site ALUMINIUM COMPOSITE PANELS (ACP) of approved make and colour certified for exterior applications, 3mm thickness with 28 to 30mm microns PVDF coating confirming to ASTM standard with top aluminium skin of 0.25mm and with a bottom aluminium skin of 0.25mm witt srvice coating of polyeater paint, laminated to a centere core of 2.5mm single recycled low density polythylene material.The pannels shall be cut to sizes of required grid dimensions with the site condition. The panel shall be fixed on pre fabricated frame work using 38mm*25mm*1mm thick Aluminium extruded sections of approved make joined with standard cleats and fasteners. The gaps formed between the panels shall be sealed with silicone sealant. The rate inclusive of cost and conveyance of all materials labour for erection, hire charges of scaffolding, etc. complete.

14.4.1 Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba / rubbish to the nearest municipal dumping ground. For door / window / clerestory window

5.9.5 Centering and shuttering including strutting, etc. and removal of form for: Lintels, beams, plinth beams, girders bressumers and cantilevers

Electrical

A/C Supply and installation of 8.5 TR duct type Air conditioner having 5 Star rating with copper pipe line works, 22 KG Duct works, 9mm nitral rubber insulation, Diffuser grill (600x300) and all other nessesary accessories

1.10.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVCinsulated copper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLSPVC insulated copper conductor single core cable etc as required.Group C

1.55.3 : Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

1.33 : Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden blockincluding connection etc as required.

1.14.1 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required 2x1.5 sq.mm + 1x1.5 sq.mm earth wire.

1.14.2 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.7 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

1.14.3 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

Supply and clamping the following size of corrugated pvc fiexible conduit with necessary locking ring and check nut at termination pointed using suitable size GI saddles spacing not exceeding 60 cms on surface including making good the damages, colour washing etc.as required 20mm dia .

Supply and clamping the following size of corrugated pvc fiexible conduit with necessary locking ring and check nut at termination pointed using suitable size GI saddles spacing not exceeding 60 cms on surface including making good the damages, colour washing etc.as required<br>25mm dia

1.17.5 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.5 X 1.5 Sq. mm

1.17.14 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.5 x 2.5 sq. mm

1.24.1 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.3 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.4 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.3 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.4 Module (125mmX75mm)

1.27.5 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)

90.10.3.15 : Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant

1.27.6 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.12 Module (200mmX150mm)

1.58 Supplying and fixing PVC batten/ angle holder including connection etc. as required.

1.26 : Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Electrical fittings

1.31 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residentia buildings).

Supply, conveyance, installation, testing and commissioning of led Slim panel Surface light with all accessories, housing made up of die cast aluminium for better heat management. Hight Transmittivity Diffuser for better light output and uniform light distribution without glare. Driver and accessories are pre wired for easy installation and long service. Voltage 230 v,CRI>80,Powerfactor>0.95, System Luminous efficacy 100LM/W;LED light source : SMD, Beam angle: 120 degree,CCT WH,WW NW, Color temperature>6000K, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<15%, Surge protection 4 KV, Multistage Isolated Constant Current operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard.Round Slim surface mounted, Wattage 15 W, similar to Luker, Wipro ,crompton,or Equivalent with luminaire lumen 2000 lm and giving connection with 3 core round flex wire .etc .complete.<br>

Supply, conveyance, installation, testing and commissioning of led Slim panel Surface light with all accessories, housing made up of die cast aluminium for better heat management. Hight Transmittivity Diffuser for better light output and uniform light distribution without glare. Driver and accessories are pre wired for easy installation and long service. Voltage 230 v,CRI>80,Powerfactor>0.95, System Luminous efficacy 100LM/W;LED light source : SMD, Beam angle: 120 degree,CCT WH,WW NW, Color temperature>6000K, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<15%, Surge protection 4 KV, Multistage Isolated Constant Current operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard.Round Slim surface mounted, Wattage 18 W, similar to Luker, Wipro ,crompton,or Equivalent with luminaire lumen 2000 lm and giving connection with 3 core round flex wire .etc .complete.<br>

Supply, conveyance, installation, testing and commissioning of led Slim panel Surface light with all accessories, housing made up of die cast aluminium for better heat management. Hight Transmittivity Diffuser for better light output and uniform light distribution without glare. Driver and accessories are pre wired for easy installation and long service. Voltage 230 v,CRI>80,Powerfactor>0.95, System Luminous efficacy 100LM/W;LED light source : SMD, Beam angle: 120 degree,CCT WH,WW NW, Color temperature>6000K, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<15%, Surge protection 4 KV, Multistage Isolated Constant Current operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard.Round Slim surface mounted, Wattage 30 W, similar to Luker, Wipro ,crompton,or Equivalent with luminaire lumen 2000 lm and giving connection with 3 core round flex wire .etc .complete.<br>

Supply and installation of pedastial FAN<br>Supply and installation of wall fan, white colour, metal leaf, 5 star rated as per BEE complete with blades, casing , wall mounting accessories etc(Make Havells/bajaj/usha/V-guard/crompton)

Exhaust Fan: Supply of 250mm sweep, 900rpm light duty exhaust fan shutter type white colour, 9&quot; or 10&quot; star rated as per BEE, with its all accessories including mounting as required for complete installation.(Make Havells/bajaj/usha/V-guard)

Supply and installation of the 9W LED lamp and other accessories in the exesting point

1.38 : Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

Supply and installation of Mirror lights of 9 Watts ; CCT : 3 in 1 ; Material: Alu Die Cast; Body colour: white ; IP rating : IP 20

DB's and components

2.3.3 : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator12 way, Double door

2.4.2 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way (4 + 18), Double door

2.4.3 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way (4 + 24), Double door

2.5.1 : Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)4 way (4 + 12), Double door

90.11.1.20 : Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required8 way (8+24) - double cover TPN vertical DB with provision for fixing MCCB as incomer and SP/ TP MCB as outgoing (IP 42/43)

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.3 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole

2.10.4 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

2.10.5 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole and neutral

Supplying and fixing following rating, 415 Volts, &apos;C&apos; curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.;40A TP MCB

Supplying and fixing following rating, 415 Volts, &apos;C&apos; curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required 63A TP MCB

2.11 : Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

2.12.1 : Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.13.1 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.13.2 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.14.2 : Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.15.2 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.16 : Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

2.2.13 : Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required100 Amp, 30 KA 4 Pole

od320555/2021_2022 : Supplying and fixing 63A FP isolator in a sheet steel enclosure on surface/ recess complete with connections, testing and commissioning etc. as required.63A FP Isolator with enclosure

2.24.3 : Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.For 8 way, Double door TPN MCBDB

4.1.1 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.100 mm width X 50 mm depth X 1.6 mm thickness

4.1.2 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.150 mm width X 50 mm depth X 1.6 mm thickness

4.1.4 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.300 mm width X 50 mm depth X 1.6 mm thickness

4.2.1 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required100 mm width X 50 mm depth X 1.6 mm thickness

4.2.2 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required150 mm width X 50 mm depth X 1.6 mm thickness

Cable & its Work

5.17 : Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing asrequired.

90.16.1.3 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG)

90.16.1.5 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required4.75 mm copper conductor (6 SWG)

90.16.5.3 : Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG)

90.16.5.4 : Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.4.00 mm (8 SWG)

90.16.5.5 : Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.4.75 mm (6 SWG)

90.12.7.2 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.2 core 6 sq mm with factory made clamp

90.12.7.27 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 25 sq mm with factory made clamp

90.12.7.30 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 70 sq mm

90.12.7.40 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 10 sq mm with factory made clamp

90.12.7.41 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 16 sq mm with factory made clamp

9.1.1 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.2 X 6 sq. mm (19mm)

9.1.20 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X25 sq.mm (28mm)

9.1.23 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.32 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.33 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

HIKVISION-7616NXI-K1 NVR : 16-ch 1U K Series AcuSense 4K NVR Up to 16-ch IP camera inputs, H.265+/H.265/H.264+/H.264 video formats, Up to 1-ch@12 MP or 2-ch@8 MP or 4-ch@4 MP or 8-ch@1080p decoding capacity, Up to 160 Mbps incoming bandwidth ,Adopt Hikvision Acusense technology to minimize manual effort and security costs

HIKVISION DS-2CD1023G0E ; 2 MP Fixed Bullet Network Camera High quality imaging with 2 MP resolution ; Ecient H.265+ compression technology, Clear imaging against strong back light due to DWDR technology ; Water and dust resistant (IP67) ; EXIR 2.0: advanced infrared technology with long IR range

Western Digital 4TB ; WD Purple Surveillance Internal Hard Drive HDD - SATA 6 Gb/s, 256 MB; Cache, 3.5" - WD42PURZ

Cat 6 Cable and Other items ; Supply and Installation Of Cat6 Cable, Pipe and Fitting, Camera Box, Camera ; Rack, Patch Panel, and other Items.

supply , installation, testing and commissioning of LED SMART TV 43" VU

supply , installation, testing and commissioning of LED SMART TV 55" VU

DS-3E1Hikvision 518P-EI/M 16 Port Gigabit Smart POE Switch ; 16 x gigabit PoE RJ45 ports, 1 × gigabit RJ45 port, 1 x gigabit ber optical ;port, Total PoE power budget 130 W, Unied cloud management for security ; systems, Network topology at your ngertips, Remote troubleshooting, Visualized topology management, Up to 300 m long-range PoE transmission, 6 kV surge protection

1.24.7 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet

1.53.1 Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable

Networking works

Supply , installation , testing and commissioning of SWITCH D-LINK 24 PORT GIGA(10/100/1000) DGS-1024D

Supply , installation , testing and commissioning of DLINK CAT6 24 PORT PATCH PANEL NPP-C61BLK241

Supply and Installtion of KEYSTONE JACK DLINK CAT

Supply and Installtion of FACE PLATE DLINK SINGLE

Supply and Installtion of D-LINK PVC 3x3 BACK BOX FOR SINGLE/DUAL

Cat6 Cable and Other items : Supply and Installation Of Cat6 Cable, Pipe and Fitting, Camera Box, Camera Rack, Patch Panel, and other Items.

supply and installtion of TP-Link Deco X20 : TP-Link Deco X20(3-Pack) 1800 Mbps Whole Wi-Fi 6 System Mesh Router

Supply and installtion of D-LINK CLOSED CABLE MANAGER 1U

supply and installtion of RACKSPACE RACK 9U 500D

3 kVA UPS

Supply installation, testing and commissioning of following three phase to three<br>phase UPS indoor (IP20) in stand alone configuration,true online double<br>conversion DSP based UPS system in stand alone configuration with inbuilt<br>parallel kit capable of connecting UPS in parallel mode when required without<br>additional cost, with 15 min backup battery ( battery of reputed make) with, input<br>pf>.99, less input current consumption, with necessary battery circuit breaker.,<br>with input 415V, 50Hz three phase, output 240V, IGBT rectifier and IGBT inverter.<br>It shall be 100% generator compatabile with efficiency > 94% and output power<br>factor > 0.9 and including all accessories etc as required. The UPS system shall<br>be with automatic & manual maintenance bypass switch facility.UPS shall<br>have seperate battery bank, and batteries shall be connected in single string.The<br>system shall comply to IEC /EN 62040-1 and relevant IS standard.The acoustic<br>noise of the system should be less than 58dB.The system shall comply to IEC /EN<br>62040-1, EN/IEC 62040-2, EN/IEC 62040-3 and relevant IS standard.<br>5 kVA UPS - 1No Battery circuit Breaker-1No Battery - Required nos.<br>of SMF for providing 15 Minutes Back UP and Battery Accessories like battery<br>rack, interconnecting cables et

Provisions for Environmental and Social items BOQ

Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

Providing and placing polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings with 4m height MS support- Temporary

Providing and placing Aluminium cool white LED Flood light 100 W including wiring

Supply and fixing of Green Net including the required supportings

Providing and placing of Portable FRP E-toilet (900x900x2250 mm) including Septic tank and plumbing materials

Supply of PPE (Helmets, Gloves, Safety boots, mask)

Providing and placing 3 litre capacity fire estiguisher

Providing and installing separate cabins for workers to ensure a safe working environment, including provisions for lighting and artificial ventilation

Conducting Occupational health and safety training, stakeholder consultation meetings

Supply and fixing 'KERALA CLIMATE RESILIENT AGRI VALUE CHAIN MODERNISATION PROJECT (KERA)' Name Board including logo using SS letter box 15 cm height

Supply and installation of a name board for the 'KERALA CLIMATE RESILIENT AGRI VALUE CHAIN MODERNISATION PROJECT (KERA)', including the logo, made of acrylic LED signage mounted on ACP (Aluminium Composite Panel), with letter height of 30 cm, complete with all necessary lighting arrangements. etc complete as per design and direction of engineer in charge

Supply and installation of the Top Hot & Cold 11L Water Purifier Kiosk, featuring an inbuilt RO+UV system, includes all necessary fittings. Dimensions of 380 x 340 x 1140 mm and operates at a rated power of 700 watts with a voltage of 230V. Plastic body

M K KAVITHA (BID ID -2219785)

Square Associates (BID ID -2219698)