C O 30 bedded CHC at Patlihuhal Tehsil Manali Distt Kullu

Amount

Excavation in foundation, trenches etc. in earth work in all kinds of soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed within all leads and lift and carriage of material in all respect as per direction of Engineer-in-charge.

Excavation in drains and channels etcetra in earth work in all kinds of clasification of soil such as pick work, jumper work,blasting work, saturated soil including chiseling or any other mixed variety of soil dewatering and / or removal of slush and other incidentals, lifts upto any height, stacking the excavated soil upto all leads and lifts clear from the edge of excavation and then returing the stacked soil in fifteen centimetre thick layers when required into plinth sides of foundation etcetra consolidating each deposited layers by ramming and watering and then disposing of all surplus excavated earth to the disposal point within all leads and lifts complete in all respect..

Filling in plinth with sand under floors including watering,ramming,consolidating and dressing complete within all leads and lift and carriage of material in all respect as per direction of Engineer-in-charge.

Providing form work with steel plates 3.15mm. (Three point fifteen millimetre ) thick welded with angle iron in frame 30x30x5mm. (Thirty x thirty x five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies height of propping and centring below supporting floor to all floor level and removal of same for insitu reinforced concrete and plain concrete work within all leads and lifts and carriage of material in all respect as per direction of Engineer-in-charge.

a) Foundation footings and bases of columns etc. and mass concrete .

b) Flat surface such as soffits of suspended floors, roofs, landing and the like floor etc. upto any thickness.

c) Columns, pillar, post and struts. Square, rectangular or polygonal in plan.any height.

d) Beams, cantilevers, girder and lintels, sides and soffits of beams, beam haunching, cantilever, brsssumers and lintels upto any depth in all height in all floor level .

e) Stair cases with sloping or stepped soffits excluding landing.

f) Vertical surfaces such as walls (any thickness)partitions and the like including attached pillasters buttresses, plinth and string courses and the like.

g) Edges of slab and breaks in floor and walls upto any width.

Providing and laying cement concrete 1:6:12 (one cement: six sand: twelve graded/ crushed stone aggregate 40mm (Forty millimetre) nominal size mechanically mixed and curing complete excluding the cost of centring and shuttering in foundation and plinth within all leads and lift and carriage of material in all respect as per direction of Engineer-in-charge.

Providing and laying cement concrete 1:4:8 ( one cement: four sand: eight graded/ crushed stone aggregate 40mm (Forty millimetre ) nominal size mechanically mixed and curing complete excluding the cost of form work in foundation and plinth within all leads and lift and carriage of material in all respect as per direction of Engineer-in-charge.

Providing and laying cement concrete 1:4:8 ( one cement: four sand: eight graded/ crushed stone aggregate 25mm (twenty five millimetre ) nominal size mechanically mixed and curing complete excluding the cost of form work in foundation and plinth within all leads and lift and carriage of material in all respect as per direction of Engineer-in-charge.

Providing and laying cement concrete 1:3:6 (One cement: Three sand: Six graded stone aggregate 40mm ( Forty millimetre)nominal size) mechanically mixed excluding cost of centring and shuttering in: Foundations and plinth: within all leads and lift and carriage of material in all respect as per direction of Engineer-in-charge.

Providing and laying reinforced cement concrete design mix M-20 (M-Twenty) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work. The mix shall be designed as per requirement of I.S. code and P.W.D. specification. The design mix will be got approved from the Engineer-In-Charge prior to the casting. The theoritical consumption of cement for the item shall be worked out as per approved design mix as per I.S. code. upto floor all floor level including carriage of material within all leads, lifts and other incidentals.

a) Walls (any thickness but not less than 0.10m ) thickness including attached pilasters, buttresses, plinth and string courses etc. from top of foundation level upto all floor level :

b) Suspended floors , roofs, landing and shelves and their supports, balconies, beams , girders, bressumers and cantilever upto any floor level.

Providing and laying cement concrete 1:2:4 (one cement: two Sand: four graded stone aggregate 20mm ( Twenty millimetre ) nominal size) mechanically mixed & vibrated and curing complete excluding cost of form work in: Foundation and plinth within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and laying reinforced cement concrete design mix M-25 ( M-Twenty five) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work . The mix shall be designed as per requirement of I.S. code and P.W.D. specification. The design mix will be got approved from the Engineer -In-Charge prior to the casting. The theoritical consumption of cement for the item shall be worked out as per approved design mix as per I.S. code upto floor all floor level within all leads and lift and carriage of material in all respect as per direction of Engineer-in-charge.

a) Foundation footings bases of columns and the like and mass concrete.

b) Suspended floors, roofs, landing and shelves and their supports, balconies, beams , girders, bressumers and cantilever upto any floor level.

c) Columns, pillar, post and struts upto any floor level.

d) Stair case with slopping or steped excluding landing but including preparing of the surface and finishing of nosing upto all floor level.

Providing and laying reinforced cement concrete design mix M-20 ( M-Twenty ) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work . The mix shall be designed as per requirement of I.S. code and P.W.D. specification. The design mix will be got approved from the Engineer -In-Charge prior to the casting. The theoritical consumption of cement for the item shall be worked out as per approved design mix as per I.S. code in mouldings as in cornices windows sills etc.upto floor all floor level including carriage of material within all leads ,lifts and other incidentals as per direction of Engineer-in-charge.

Providing tor steel reinforcement for R.C.C. work including bending, binding and placing in position including cost of binding wire complete upto floor any level within all leads and lift and carriage of material in all respect as per direction of Engineer-in-charge.

Providing and laying cement concrete 1:2:4 (one cement: two Sand: four graded stone aggregate 20mm ( Twenty millimetre ) nominal size) mechanically mixed & vibrated and curing complete excluding cost of form work in: Foundation and plinth within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing in RCC work smooth finishing of the exposed surface with cement mortar 1:3 (One cement : three sand) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Brick work using common burnt clay building brick in super structure in cement mortar 1:6 (One cement : Six sand ) with 2nd class bricks upto all floor level.within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Half brick masonry in common burnt clay building bricks in super structure in cement mortar 1:3 (One cement : three sand ) 2nd class bricks upto all floor level.within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Stone filling under floor with hard stones of approved quality within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Random rubble masonry/polygonal rubble masonry (uncoursed / brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (One cement :six sand : twelve graded stone /crushed aggregate 20mm (Twenty millimetre ) nominal size) at plinth level in cement mortar 1:6 (One cement: six sand) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including raking out joints in:- Cement mortar 1:3 (one cement : three sand) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including raking out joints in Cement Mortar 1:6 (One cement : Six sand) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Extra for forming cavity 5cm. to 7.5cm. ( Five centimetre to seven point five centimetre) wide in cavity walls with necessary weep and vent holes including use of cores and cost of providing and fixing bitumastic coated M.S. Ties of 25mm x 3mm (twenty five millimetre X three millimetre) section at not less then 3 ( Three ) ties per square metre as per approved design Concrete block within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Precast concrete block masonry (including quion blocks,jamb blocks, closer etc.) with solid concrete blocks of approved size made of cement concrete 1:3:6 (one cement: three sand: six graded stone aggregate 40mm ( Forty millimetre ) and down gauge) foundation and plinth up to all floor level in Cement Mortar 1:6 (one cement : six sand) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Precast concrete block masonry in partition walls 10 cm ( Ten centimetre ) thick with solid block of approved size including quion blocks, jamb blocks, closer etc. made of cement concrete 1:3:6 (one cement: three sand: six graded stone aggregate 40mm ( Forty millimetre ) and down gauge) in Cement Mortar 1:6 (one cement : six sand) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing anodised aluminium work for door, window, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawlplugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazinge/panelling C.P. brass/stainless steel screws. All complete as per architectural drawings and the directions of Engineer-In-Charge.For doors windows and ventilatiors and glazed partitions frames within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing anodised aluminium work for door, window, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawlplugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazinge/panelling C.P. brass/stainless steel screws . For shutters of doors windows & ventilators including providing and fixing hinges/pivots and making provisions for fixing of fittings where ever required including the cost of PVC/neoprene gaskets as required (fittings and glazing/panelling shall be paid for separately) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 5.5 mm (Five Point Five Millimetre) thick toughened glass both side, having 12 mm ( Twelve millimetre) air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc complete in all respect within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing aluminium anodised powder coated gril of required pattern to existing\ window/ventilatior with 80mmx80mm (Eighty x Eighty millimetre) panels holes with 25x8mm ( Twenty five x Eight millimetre) thick aluminium flat in windows and ventilators including fixing with aluminium screws or bolts nuts complete in alluminium channels base frames (Aluminium channels base frames to be measured and paid for separtely within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing Aluminium sheet 1mm ( One millimetre ) thick in expension joints vertically fixed with screws or nails complete within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing Aluminium sheet ceiling with 1mm ( One millimetre ) thick Aluminium sheet in panets of aluminium channels base frame in ceiling with aluminium screws and aluminium beading 40x2mm ( Forty x Two millimetre ) complete (Aluminium channels base frame to be measured and paid for separately) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing GRC Jali of standard make and manufacture complete as per drawing and specification within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Prelaminated board bwp phenol bonded exterior/interior grade both sides.12mm ( Twelve millimetre ) thick for door and shutter in all respect as per drawing and specification within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Prelaminated board bwp phenolbonded exterior/interior grade on one side. 12mm ( Twelve millimetre ) thick for door and shutter complete complete as per drawing and specification within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing 19mm ( Nineteen millimetre ) thick Commercial Board water proof shutters for cup boards including fixing with nickel plated piano hinges with screws etc. complete within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing 19mm ( Nineteen millimetre ) thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nails & screws etc. complete) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing 1.00mm ( One millimetre) thick coloured or plain lamination sheet (sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete. within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing square edges cover fillets (beading) 19mmx6mm ( Nineteen millimetre x Six millimetre ) section including mitring at junctions with wood screws and nails complete with 1st class Indian teak wood within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing magnetic catcher with screws etc. complete within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete.within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

a) 300 x 16mm ( Three hundred x Sixteen millimetre)

b) 250 x 16mm ( Two hundred fifty x Sixteen millimetre)

Providing and fixing aluminium tower bolts (barrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete.within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

a) 200 x 10mm ( Two hundred x Ten millimetre)

b) 150 x 10mm ( One hundred Fifty x Ten millimetre)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete.125mm ( One hundred twenty five millimetre ) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing oxidized M.S. hooks and eyes.150mm ( One hundred fifty millimetre) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing uni-stone 12mm ( Twelve millimetre ) thick cladding on brick work / R.C.C. surface on 12mm ( Twelve millimetre ) thick cement plaster in cement mortar 1:3 ( one cement : three sand) and jointed with cement slurry including scaffolding ,etc. complete within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Cement planks Cladding on base of G.I. frame of Everest or it's equivalent, Finished with exterior grade polish. Including necessary screws etc. complete as per drawing specification within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing 10mm( Ten millimetre ) thick Full body vetrified tiles Nitco or equivalant 600 x 600mm x 10mm ( Six hundred x six hundred x ten millimetre ) manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick ( Twelve millimetre ) cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete as per drawing and specification within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing 10mm( Ten millimetre ) thick full body glazed anti skid tiles (with VC shield technology ) water proof stain and impect resistent heavy duty vetrified tiles Nitco orequivalant 605mm x 605mm x 10mm ( Six hundred five x Six hundred five x Ten millimetre ) manufactured of approved shade and colour in flooring, with 20 CM ( Twenty centimetre ) border of granite stone, treads of steps and landings laid over 12mm ( Twelve millimetre )thick cement mortar 1:3 (One cement : Three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete as per drawing and specification within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing Antistatic Vetrified 10 mm ( Ten millimetre ) thick flooring of Nitco, RAK, Kajaria or equivalant 600 x 600 x 10 mm (Six hundred x Six hundred x Ten millimetre ) conductive less than 01 Mega Ohm with static decay time less than 0.5 seconds ( Point Five Seconds ) The tiles should be fixed using the the tile adhesive. Tiles suitable to fix antistatic vitrifeis in minimum 6mm ( Six millimetre ) thick bed and by leaving aspace minimum 5mm around each with the hwlp of + shaped PVC spacer suitable to leave a grove of 5 mm ( Five millimetre ) around all four side of each tile. A grid of 18 gauge ( Eighteen gauge ) anilated pure copper wire around all four side of antistatic tile. All groves shoud be filled with black colured antistatic epoxy grout spectrum-ASEG complete as per specification within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Kota stone slab flooring 20 mm ( Twenty millimetre ) (average) thick base of cement mortor 1:4 (One cement : Four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and polishing complete. 25 mm ( Twenty Five millimetre ) thick.within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing 10mm ( Ten millimetre ) thick anti skid Duro stone vetrified tiles Nitco or equivalant 300 mm x 300 mm x 10 mm (Three hundred millimetre x Three hundred millimetre x Ten millimetre ) manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm ( Twelve millimetre ) thick cement mortar 1:3 (One cement : Three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete .within as per specification all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and laying 20mm ( Twenty millimetre ) thick anti bacterial dust resistant, washable germ free tiles of the size 30 Cm. x 60 Cm.( Thirty centimetre x sixty centimetre ) of specified shade in floors, treads of steps and landing laid on a bed of 12mm ( Twelve millimetre ) thick acid proof mortor 1:3 (One cement: Three sand) jointing with cement slurry mixed with pigment to match the shade of tile .complete as per drawing and specification within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and laying red sand stone slab flooring 40mm ( Forty millimetre ) average thick on 20mm ( Twenty millimetre ) average thick base of cement mortar 1:4 (One cement : Four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polish finish complete .within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and laying granite stone in flooring 20mm ( Twenty millimetre ) (average)thickness base of cement mortar 1:3(One cement: Three sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete. 20mm ( Twenty millimetre ) thick within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Granite stone slab 20 mm ( Twenty millimetre ) thick in risers of steps,skirting dado and pillars laid on 12 mm ( Twelve millimetre ) (average) thick cement mortar 1:3 (One cement : Three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete..within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

10 CM ( Ten centimetre ) high skirting of full body glazed anti skid tiles (with VC shield technology ) . 10 mm ( Ten millimetre ) thick in risers of steps,skirting dado and pillars laid on 12 mm ( Twelve millimetre ) (average) thick cement mortar 1:3 (One cement : Three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete .within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and laying digital ceramic glazed tiles 8mm ( Eight millimetre ) thick (300 x600 mm) ( Three hundred x six hundred millimetre ) size in skirting risees, steps and dado. laid on a bed of 12mm ( Twelve millimetre ) thick cement mortar 1:3(one cement: three sand) finished with flush pointing in white cement within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Granite tiles 10 mm ( Ten millimetre ) thick in skirting, risers of steps and dado ( Size 300 X 600 mm) ( Three hundred x Six hundred millimetre ) laid on a bed of 12 mm ( Twelve millimetre ) thick cement mortar 1:3(One cement :Three sand) finished with flush pointing in white cement within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and laying Duro stone vetrified tiles (300x300mmx10mm) ( Three hundred x three hundred x ten millimetre ) in grey/coloured or of approved shadetreads and rises of steps dodo etc. and landing laid on a bed of 12mm ( Twelve millimetre) thick cement mortar 1:3 (one cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing Antistatic Vitrified 10 mm ( Ten millimetre ) thick of Nitco, RAK, Kajaria or equivalant 300 x 300 x 8 mm ( Three hundred x Three hundred x Eight millimetre ) thick in risers of steps,skirting dado with conductive less than 01 Mega Ohm with static decay time less than 0.5 seconds ( Point Zero Seconds ). The tiles should be fixed using the the tile adhesive. Tiles suitable to fix antistatic vetrifeis in minimum 6mm ( Six millimetre ) thick bed and by leaving aspace minimum 5mm ( Five millimetre ) around each with the hwlp of + shaped PVC spacer suitable to leave a grove of 5 mm ( Five millimetre ) around all four side of each tile. A grid of 18 gauge ( Eighteen gauge ) anilated pure copper wire around all four side of antistatic tile. All groves shoud be filled with black colured antistatic epoxy grout spectrum-ASEG .complete as per drawing and specification within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Kota stone slab 25 mm ( Twenty five millimetre ) thick in risers of steps,skirting dado and pillars laid on 12 mm ( Twelve millimetre ) (average) thick cement mortar 1:3 (One cement : Three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete.within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and laying 20mm ( Twenty millimetre ) thick anti bacterial tiles of size upto 300 x 300mm ( Three hundred x Three hundred millimetre ) of specified shade in skirting risers of steps and dado on a bed of 12mm ( Twelve millimetre ) thick acid proof mortor 1:3 (One cement: Three sand) jointing with cement slurry mixed with pigment to match the shade of tile .within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing 0.60mm ( Zero Point sixty millimetre ) thick prepainted steel sheet in roofing and chajjas with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 ( Twenty ) microns over 5 (Five) microns primer coating to back coat of polyster of 5 ( Five ) microns over 5 ( Five ) microns primer coating including fixing with screws prepainted iron J or L hooks, bolts and nuts 6mm ( Six millimetre ) dia metre with prepainted limpet and rubber washers complete with all accessories as required as per the within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing ridges or hips 60 cm ( Sixty centimetre ) overall with 0.60mm ( Zero Point sixty millimetre ) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (Twenty ) microns over 5 (Five ) microns primer coating + back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with screws prepainted iron J or L hooks, bolts & nuts 6mm ( Six millimetre ) dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing valley 90 cm ( Ninety centimetre ) overall 0.60mm ( Zero Point sixty millimetre ) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (Five ) microns over 5 ( Five ) microns primer coating including fixing with screws prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing 15 cm. ( fifteen centimetre ) wide 45 cm. ( Forty five millimetre ) overall semicircular 0.60mm ( Point Sixty millimetre ) thick Steel sheet pre painted sheetgutter with prepainted iron J or L hooks, bolts and nuts 6mm ( Six millimetre ) dia metre with prepainted limpet and rubber washers complete with all accessories as required as per the direction of Engineer-in-charge.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm ( Four Point Five Kilograms/Square metre ) including filling the joints with approved adhesive complete within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

(a) 100 mm ( One hundred millimetre ) dia pipe

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete the within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

i) PVC Plain bend 100mm ( One hundred millimetre ) dia.

ii) PVC corner type bend 100mm ( One hundred millimetre ) dia .

iii) PVC shoe 100mm dia ( One hundred millimetre ) dia.

Providing and fixing M.S. BP Sheet 1.66mm ( One point sixty six millimetre ) to 2mm (Two millimetre ) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge. (Base members of steel work shall be measured & paid separtely)

Providing and fixing polycarbonated transparent sheet 1.20mm ( One Point Twenty millimetre ) thick in roofing with galvanised J or L hooks bolts and nuts with G.I. Limpet and bitumen rubber washer complete with all accessories as required as per direction of Engineer-in-Charge.Including carriage of materials within in all lead , lift & other incidentals.

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

a) In beams joists channels ,angles, tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like.

b) In gratings framed guard bars,ladders, railling, brackets and similar works.

Supplying and fixing rolling shutters of approved make made of 80 mm X 1.25mm ( Eighty millimetre x One point Twenty five millimetre ) M.S laths interlocked together through their entire length and joined together at the end by end locks mounted on specially designed pipe shaft,with brackets side guides and arrangements for inside and outside locking with push pull operation complete but excluding the cost of the top cover and spring within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

(i)Shutters having width below 3.5 metres ( Three point five metres ) (Rolling shutters operated by bevel gear box and crank handle exceeding 12.0 sq.m. ( Twelve Square metre ) and upto 25.0 sq.m ( Twenty Square metre ) in area (average say 18.5 sq.m ( Eighteen Point five square metre )

Providing and fixing of Stainless Steel (Grade 304 with Brush Finish) Staircase Railing as per details drawing abd desugb of KICH or equivalent make Top mounted square baluster system with Horizontal Members (model no. DT53-1-163) with top brackets, middle member connector, mounting system, base fitted with cover cap, top railing pipe is od 50mmx50mm ( Fifty x Fifty millimetre ) square and three nos of middle pipes of 38mm ( Thirty eight millimetre ) dia pipes and anchouring to grainate steps, chemical grouting of bolts and all fittings including all members and labour as directed by the engineer in charge and making the surface in good condition. The top of the railing pipe is of 50mm ( Fifty millimetre ) dia within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Painting two costs (excluding priming coat) on new steel and other metal surfaces with enamel paint brushin to give an even shadeincluding cleaning the surface of all dirt,dust and other foregin matters .Enamel paint other than white within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for making the surface within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

6mm ( Six millimetre ) Cement plaster to ceiling. In Cement mortar 1:3(one Cement: three Sand) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

15mm (Fifteen millimetre ) cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor all level including rises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm ( Eighty millimetre ) in girth and finished even and smooth.In Cement mortar 1:3(one Cement: three Sand) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

20mm ( Twenty millimetre ) Cement plaster in two coats,backing coat 15mm ( Fifteen millimetre ) and finishing coat 5mm ( Five millimetre ) thick on rough side of brick/stone masonry walls for interior plastering upto floor all level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth In cement motor 1:6 ( One cement ; Six Sand ) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing plinth protection 50mm ( Fifty millimetre ) thick in cement concrete 1:3:6 (one Cement : three Sand : six Graded stone aggregated 20mm ( Twenty millimetre ) nominal size) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing under layer for plinth protection of 75mm ( Seventy five millimetre ) thick (unconsolidated) bed dry brick/stone aggregated 40mm ( Forty millimetre ) nominal size with rammed and consolidated and grouted with fine sand including preparation of ground within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Constructing U-shape open surface drain course rubble hammer dressed with side wall 15x22cm(Fifteen x twenty two centimetre ) in cement mortar 1:6(One cement :Six sand) and inside plastering with cement mortar 1:3 ( One cement: Three sand) including earth work and laying 10cm.(Ten centimetre) cement concrete 1:5:10 (One cement : Five sand : Ten graded /crushed stone aggregate) of 40mm.(Forty millimetre) nominal size and 7.5 cm(Seven point five centimetre) cement concrete 1:2:4(One cement: Two sand: Four graded /crushed stone aggregate of 20mm.(Twenty millimetre) nominal size) and finished with a floating coat of neat cement complete as per standard design within all leads and lift and carriage of material in all respect as per direction of Engineer-in-charge.

W S & S I :- Providing separately. and fixing vitreous China wash down, water closet squatting pan (Indian type W.C pan) size 580mm ( five hundred eighty millimetre) (Earth work, bed concrete, foot rest and trap to be measured and paid for separately). Orissa Pattern within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing vitreous China wash down,water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1 ( One cement : One sand) (Seat and over to be measured and paid for separately) Anglo Indian Universal closet within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing G.I. Inlet connection for flush pipe with W.C.Pan within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers Solid type white plastic seat and cover within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing vitreous China bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with choppe hemp (waste pipe to be measured and paid for separately) Flat back type of size 430mm x 260mm x 350mm ( Four hundred thirty x two hundred sixty x three hundred fifty millimetre ) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing automatic flushing cistern with a pair of C.I. Or M.S. brackets complete with fittings including C.I. Syphonic apparatus, mosquito proof lid, C.P. Brass unions and coupling for connections with inlet, outlet and overflow pipes including cutting holes and making good the same (overflow pipe to be measured and paid for separately) :- Vitreous China 5 ( Five ) litres capacity within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing C.P. brass flush pipe / spreaders for urinal with fitting such as unions, clanmps etc. (all in C.P. Brass) including cutting holes and makng good the same :- 15mm ( Fifteen millimetre ) nominal bore within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings. Flat back 550mm x 400mm ( Five hundred fifty millimetre x four hundred millimetre ) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing vitreous China padedstal for wash basin complete recessed at the back for the reception of pipes and fittings within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing rubber plug for sink / wash basin.32mm ( Thirty two millimetre ) dia within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing C.P. Brass waste for wash basin or sink. 32mm ( Thirty two millimetre ) dia within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing M.I. Union for wash basin or sink. 32mm dia ( Thirty two millimetre ) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing 600mm x 450 mm (Six hundred millimetre x four hundred fifty millimetre) bevelled edge miror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge..

Providing and fixing C.P. Brass Towell rail coplete with C.P. Brass brackets fixed to wooden pluges with C.P. Brass screws :- 600mm x 20mmm (Six hundred millimetre x twenty millimetre) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing C.P. Brass Towel ring coplete with C.P. Brass brackets fixed to wooden pluges with C.P. Brass screws within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing 600mm x 120 mm (Six hundred millimetre x one hundred twenty millimetre) glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden pluges with C.P. Brass screws within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing Toilet paper holder C.P. Brass within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing charomium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing Division Plate for Urinals 600mm x 300 (Six hundred x three hundred millimetre). Vitreous China within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

(i) Providing and fixing C.P Brass bib tap with Capstan head 15mm (Fifteen millimetre) dia within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge

(ii) Providing and fixing C.P Brass pillar tap with Capstan head 15mm (Fifteen millimetre) dia within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge

Providing and fixing C.P. brass angle valve 15mm (Fifteen millimetre) without nuts and pipe within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge

Providing and fixing C.P. stop cocks .15 mm (Fifteen millimetre) dia within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge

Providing and fixing PVC. connection pipe with brass unions 300/450mm ( Three hundred / Four hundred fifty millimetre ) length :- 15 mm (Fifteen millimetre) nominal bore within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing brass full way valve with wheel. 15mm (Fifteen millimetre) nominal bore within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-AL-PE) composite pressure pipe U.V. stablized with carbon black confirming to IS-15450-2004 water supply including clamp at one metre spacing, cutting, fixing and making good the wall etc. but excluding the cost of fittings (internal work) pipes exposed on wall 1216 -16mm ( Sixteeen millimetre ) O.D. pipe) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

(a)Equal Tees. (i) 1216

(b)Female branch TEE. (i) 1216 x 1216 x 15mm ( Fifteen millimetre) thread.

(c)Female elbows:- 1216 x 15mm ( Fifteen millimetre) thread.

(d)Male thread connector:-1216 x 15mm ( Fifteen millimetre) thread.

(e)Female thread connector:- 1216 x 15mm ( Fifteen millimetre) thread.

(f)Couplers:- (i) 1216

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS-15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

(a)Equal Tees. (i) 1216

(a)Female branch TEE. (i) 1216 x 1216 x 15mm ( Fifteen millimetre) thread.

(b)Female elbows:- 1216 x 15mm ( Fifteen millimetre) thread.

(c)Male thread connector:-1216 x 15mm ( Fifteen millimetre) thread.

(d)Female thread connector:- 1216 x 15mm ( Fifteen millimetre) thread.

(e)Couplers:- (i) 1216

Providing and fixing PVC water storage tank of ISI : 12701 marked,G.I. inlet and outlet connection, 15mm ( Fifteen millimetre ) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level 1000 ( One thousand ) litres net capacity tank within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

(i)110 mm X 90 mm (One hundred ten millimetre x ninety millimetre )

(ii)110 mm X 75 mm (One hundred ten millimetre x Seventy five millimetre )

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

(i)110 mm (One hundred ten millimetre ) dia.

(ii)75 mm ( Seventy five millimetre ) dia.

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm ( Three millimetre ) thick bolts and nuts complete including fixing with approved adhesive etc. complete within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

(i)110 mm (One hundred ten millimetre ) dia.

(ii)75 mm ( Seventy five millimetre ) dia

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm ( Three millimetre ) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

(i)110 mm (One hundred ten millimetre ) dia.

(ii)75 mm ( Seventy five millimetre ) dia.

Providing and fixing PVC cowl IS marked including fixing with approved adhesive etc. complete.within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete..within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

(i)110 mm (One hundred ten millimetre ) dia.

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc. complete within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

(i)110 mm (One hundred ten millimetre ) dia.

(ii)75 mm ( Seventy five millimetre ) dia.

Providing and fixing PVC collers ISI marked including fixing with approved adhesive etc. complete within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

(i)110 mm (One hundred ten millimetre ) dia.

(ii)75 mm ( Seventy five millimetre ) dia.

(ii)75 mm (One hundred ten millimetre ) dia.

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

(i)110 mm (One hundred ten millimetre ) dia.

(ii)75 mm (One hundred ten millimetre ) dia.

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fitting.610 x460 mm ( Six hundred ten millimatre x Four hundred sixty millimatre ) with bowl depth 200 mm ( Two hundred millimetre ) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing PTMT Coloured / white high density polythylene / poly propylene 10 ( Ten ) litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm ( Fifteen Millimetere)nominal size PVC ball valve with polythene float,with push button,couplings for connections with inlet, outlet and over flow pipe, 40mm ( Forty millimetre) dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) within all leads and lift and carriage of material in all respect as per direction of Engineer-in-charge.

Providing and fixing PTMT waste coupling of approved quality and colour 32 mm ( Thirty two millimetre) nominal bore complete within all leads and lift and carriage of material in all respect as per direction of Engineer-in-charge.

Providing and fixing PTMT urinal waste coupling of approved quality and colour within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Providing and fixing 100 mm ( Hundred millimetre ) dia curomium plated grating of superior quality for floor, gully or nahani trap complete within all leads and lift and carriage of material in all respect as per direction of Engineer-in-charge.

Providing and fixing stoneware gully trap grade 'A' complete with C.I grating, brick masonry chamber in cement mortar 1:5 and water tight C. I . cover with frame of 300mmx300mm ( Three hundred x three hundred millimetre) size (inside) the weight of cover to be not less than 4.53kg ( Four point fifty three kilogramme ) and frame to be not less than 2.72kg ( Two point seventy two kilogramme ) . Round Mouth Traps:100mm x 100mm size ( One hundred X One hundred millimetre) P or S type within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

Constructing manhole with R.C.C top slab in 1:2:4 mix(one cement : two sand : four graded stone aggregate 20mm( Twenty millimetre) nominal size) foundation concrete1:4:8 (one cement : four sand : eightgraded stone aggregate 40mm ( Forty millimetre ) nominal size) inside plastering 15mm ( Fifteen millimetre) thick with cement mortar 1:3 (one cement :three sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (one cement : two sand : four graded stone aggregate 20mm ( Twenty millimetre) nominal size) finished smooth complete including curing and testing complete within all leads and lift and carriage of material in all respect as per direction of Engineer-in-charge.

(i) Inside size 800mm x 800mm ( Eight hundred x eight hundred millimetre) and 500mm ( Five hundred millimetre) deep including C.I cover with frame. (Light duty single seal pattern - 1) 455 mmx610mm( Four hundred fifty five millimetre x Six hundred ten millimatre) internal dimensions total weight of cover and frame to be not less than 38kg( Thirty eight Kilogramme) .weight of cover 23 kg ( Twenty three Kilogramme) and weight of frame 15 kg( Fifteen Kilogramme) (a) With 300mm( Three hundred millimetre) thick walls of squared rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (one cement : three sand).

(ii) Inside size 800 mm x 800 mm and 1000 mm ( Eight hundred x eight hundred millimetre) and 1000mm ( one Thousand millimetre) deep including C.I cover with frame. (Light duty single seal pattern - 1) 455mmx610mm ( Four hundred fifty five millimetre x Six hundred ten millimatre) internal dimensions total weight of cover and frame to be not less than 38kg( Thirty eight Kiligramme) . (weight of cover 23 kg ( Twenty three Kilogramme) and weight of frame 15 kg( Fifteen Kilogramme) (a) With 300mm( Three hundred millimetre) thick walls of squared rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (one cement : three sand).

Providing and fixing electrical Gyser best quality I.S.I. marked having 25 ltrs ( Twenty five litre) Net water capacity with necessary accessories etc. complete in all respect within all leads and lift and carriage of material in all respect as per direction of Engineer-in-charge.

Suppliying cast iron cover without frame for manholes For frame of internal dimension 455mmx610mm ( Four hundred fifty five x six hundred ten millimetre ) rectangular C.I. cover (light duty single seal pattern-1) the weight of cover to be not less than 23kg ( Twenty threee Kilogramme ) within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge.

SUNIL SOOD