RAISING OF COMPOUND WALL AND ANGLE IRON WITH FENCE AT CGRA AND ICGS BEYPORE, ADDITION ALTERATION TO SPORT COMPLEX AT ICGS BEYPORE, ADDITION ALTERATION TO ROOF AND VALLEY GUTTER AT BOAT REPAIRING SHED NO.1 AND 2 AT ICGS BEYPORE, PROVN OF DRAINAGE

Amount

Demolition of brick work or stone masonry, built in cement mortar including all quoins, pillars etc and removal from site complete all as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as directed.

Taking down cement plastering of any description on concrete or Brick works surface racking out joints, hacking for key , scrubbing down with water etc complete all as specified and as directed.

Material and labour plain cement concrete 1:3:6 type C2 using 40 mm graded stone aggregate as in foundations and mass concrete all as specified and as directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.5 meter in depth and getting out excavated earth, forming bottom surfaces to required level complete all as specified and directed.

Supply and fix in repairs Galvanized, 2 strand, steel barbed wire 2.24 mm dia, barbed with 2 mm dia., barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including secruing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pins, etc. complete all as specified and directed. (each line wire to be measured)

Material and labour for deformed TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips all as specified and as directed.

Material and Labour for TMT bars 5 mm to 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

Material and labour for providing cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate cast in situ as in copings/bed block and the like including weathering, slightly rounded or chamfered or chamfered angles as directed including use of form work as necessary all as specified and as directed.

Use and waste of formwork to sides of pillars, post, struts, piers, coloumn and stanchions, square, rectangular or polygonal, rough finished surfaces of concrete all as specified and as directed.

Use and waste of form work to edges of concrete flats, threads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exceeding 10 cm but not exceeding 20 cm wide for fair finished surfaces.

Material and Labour for Broken glass coping on top of walls, approximately 63mm gauge, firmly embedded in rendering in cement mortar 1:3 at the rate of 10 Kg of glass per square metre, jogged edges of the glass being left projecting complete all as specified and as directed.

Returning, filling in soil including spreading leveling, watering and well ramming in layers n.exc.25cm thick complete all as specified and as directed.

Removing excavated soil to a distance n.exc 50m, and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Taking down old galvanised 2 strand steel barbed wire and refixing 2.24 mm barbed with 2mm dia barbs at 75 mm spacing and straning and fixing to fencing post with staple or steel pins etc complete all as directed and specified.

Restraining and resecuring including making good staples etc galvanized 2 strand steel barbed wire 2.24 mm barbed with 2mm dia barbs at 75 mm spacing and straning and fixing to fencing post with staple or steel pins etc complete all as directed and specified.

Material and labour for precast cement concrete solid block masonry using Solid PCC block type C4 exceeding 10 Cm width, built in cement mortar 1:6 all as specified and as directed.

Material and labour for rendering 10mm on fair faces of brick or concrete surfaces in CM 1:4, finished even and fair without using extra cement complete all as specified and directed.

Material and labour for rendering 15mm on other than fair faces of brick or concrete surfaces in CM 1:4, finished even and fair without using extra cement complete all as specified and directed.

Supply and fix angle iron, flats as in posts, struts or boundary wall including cutting tops to shape as directed, drilling holes, notching for wire etc conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

Material and labour for Plain cement concrete 1:2:4, type B1, using 20mm graded stone aggregate as in bed block for hold fast and similar works including necessary form work all as specified and as directed.

Material and labour for Reinforced cement concrete M-30 design mix using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts etc all as specified and as directed.

Material and labour for applying two coats of cement based paint wall over a coat of primer including preparation of new surface of wall complete all as specified and directed.

Material and labour for preparation of old treated wall surfaces by washing, rubbing, brooming down or steel wire brushing or scraping down smoke soot, moulds, mass and efflorescent salts, and applying one coat of cement based paint on walls all as specified and as directed.

Material and Labour for preparation of new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and as directed.

Excavation in post holes (or similar holes) each n exc 0.5 cum and getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n exc 25cm, watering and removing surplus soil to a distance n exc 50m and making good surface in hard / dense soil complete all as specified and directed.

Supply and fix structural steel work in tubular trusses including special shaped washer of 6mm thick MS sheeting etc complete using ERW or induction butt welded tubes conforming to IS - 1161-1979 grade St.-240 all as specified and as directed.

Supply and fixing Pre- painted galvalume aluminum zinc coated corrugated sheet of 0.50mm thickness having tensile strength of 550 Mpa with coating thickness fixed with GI self taping screws as in roof covering/cladding to wall, ridges, valley gutters fixed to frame work all as per manufacturers instructions all as specified and as directed.

Supply and fixing Pre- painted galvalume aluminum zinc coated 0.5mm thick prepainted plain galvalume sheeting as in ridge and cladding, fixed with GI self tapping screw complete all as specified and as directed.

Dismantling boarding/false ceiling any description fixed in any position with nails complete all as specified and directed.

Dismantling of battens for tiles, shingles etc of any size including tilting fillets spaced not exceeding 15 cm complete all as specified and directed.

Dismantling timber unframed in rafters, purlins etc. under 40 sqcm in section, in any position complete all as specified and directed.

Material and labour for 100mm thick precast cement concrete solid block masonry using Solid PCC block type C4 not exceeding 10 Cm width, setting in mortar 1:4 complete all as specified and as directed.

Material and labour for 5mm thick Rubber sheet flooring with fabric backing or insert and plain coloured or marbled ropping mat or glossy laid in floors with approved adhesive complete all as specified and directed.

Material and labour for providing cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate cast in situ as in band in brick course including necessary form work complete all as specified and as directed.

Supply and fix anodised aluminium snap grid frame work for false ceiling with 605mm x 605mm size, consisting of main Tee of size 23.50mmx36.50mmx1.50mm, cross Tee of size 23.50mmx23.50mmx1.50mm and wall angle of size 36.00mmx25.00mmx1.50mm of approved make including all necessary cuttings, fixing of aluminium section firmly in position with and including steel hangers 6 mm dia G.I. wire (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60 mm long and expansion hold fasteners 40 mm long in soffit of slab/walls including provision of 12mm thick gypsum board 600mmx600mm size, fixed in ceiling, flat or sloping complete all as specified and directed.

Material and labour for preparation of new surfaces on wall and applying two coat of acrylic distemper over one coat of primer etc complete all as specified and as directed.

Material and Labour for preparing of old treated surfaces of any description and applying one coat of acrylic distemper, white or tinted on old plastered wall surface complete all as specified and as directed.

Material and labour for 100mm thick plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in flooring finished even and smooth including necessary form work complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for unreinforced complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding and removing rubbish off the premises complete all as specified and as directed.

Material and labour for 75mm thick plain cement concrete 1:3:6 type C2 using 40 mm graded stone aggregate as in sub base flooring finished even and fair including necessary form work complete all as specified and as directed.

Material and Labour for non-skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.18sqm but not excceding 0.38 sqm, in floors etc, set and jointed in cement mortar and pointed in white of coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

Material and labour for rendering 15mm on fair faces of brick or concrete surfaces in CM 1:4, finished even and fair without using extra cement complete all as specified and directed.

Material and labour for rendering 15mm on faces of brick or concrete surfaces in CM 1:6, finished even and fair without using extra cement complete all as specified and directed.

Material and labour for glazed ceramic coloured tiles in vertical surface 300x200x7mm set and jointed in neat cement slurry over and including backing coat of 10mm thick in CM 1:3 complete all as specified and directed.

Material and labour for 38mm width glass dividing strips, 3mm thick inserted in position, confirm to design complete all as specified and directed.

Taking down Chowkats or frames not exceeding 1.5 Sq. M each (without taking off shutters from the frames) complete all as specified and directed.

Taking down Chowkats or frames exceeding 1.5 Sq. M but not exceeding 4 Sq. M each (without taking off shutters from the frame) complete all as specified and directed.

Supply and Fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening complete all as specified and directed.

Supply and fix Factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame complete all as specified and directed.

Material and labour for second class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with glued pinned at joints, fixed to wall and making good to wall all as specified and directed.

Supply and fixing 2nd class hardwood factory made plain framed panelled shutters (any number of panels) 30mm thick with lock rail and with panels of 12mm thick commercial veneered particle board veneers on both side or with 9mm thick BWP commercial ply, size of members of shutters as specified in IS 1003-Part-I, kiln seasoned and chemically pressure treated complete all as specified and as directed.

Supply and Fix 100mm long aluminium anodised barrel tower bolt extruded section complete all as specified and as directed.

Supply and Fix 150mm long aluminium anodised barrel tower bolt extruded section complete all as specified and as directed.

Supply and fixing aluminium alloy,anodised, sliding door bolt of length 300mm with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded section or cast-aluminium alloy complete all specified and as directed.

Supply and fix 100 mm long extruded Aluminium alloy anodised Butt hinges with galvanized mild steel hinge pin type C 21 complete all as specified and directed.

Supply and fix extruded aluminium handles fabricated type anodised of size 100mm complete all as specified and as directed.

Supply and fix extruded aluminium handles fabricated type anodised of size 150mm complete all as specified and as directed.

Supply and fix Brass Chromium plated tubular towel rail, 20 mm dia., D Type, 60 cm long between flanges complete all as specified and directed.

Supply and fix in repairs Floor door stopper of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 150 mm complete all as specified and directed.

Supply and fix door closer hydraulically regulated aluminium extruded section, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed complete all as specified and as directed.

Laying only precast cement concrete solid block masonry, built in cement mortar 1:6 all as specified and as directed.

Material and labour for rendering 10mm on fair faces of brick or concrete surfaces in CM 1:6, finished even and fair without using extra cement complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge in roof coverings complete all as directed.

Supply and fix plain, galvanised, mild steel sheeting 1.25 mm thick, in ridges, hips and valley gutters, bend to shape, fixed with coach screws and washers complete all as specified and directed.

Supply and fix 2mm thick polycarbonate solid sheet with sealed end and fixed with self driven screw complete all as specified and as directed.

Supply and fix Plates confirm to FE-410W (GDE-E -250 quality-B) (Plain or chequired) channels, square cut or notched(ordinary and counter sunk with out any attachment complete all as specified and directed.

Supply and fix 150mm dia PVC eve gutters fixed mild steel clamps to roof and connected to rain water pipes etc complete connecting to eves gutters complete all as specified and directed.

Supply and Fixing Mild steel work such as joist, channel, angle or tee section fixing independently without connecting plates, cut to ordinary length ie, within 20mm of the length indicated conforming to Grade E-250, Fe 410 W quality B all as specified and as directed.

Supply and fix Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including necessary hangers6mm dia GI up to1200mm length adjusting level fixed to roof slab by means of cleats made out of FI 40x3mm size 60 cm long and expansion holdfast 12.5mm dia 40mm long with and including fixing of 12.5mm thick gypsum board seamless 600mmx600mm size with self tapping screw finishing the joints with fiber tape and ceiling compound complete all as specified and as directed.

Cutting holes in brick walls built in cement mortar for inserting hold fasts, end of post and struts and making good the dismantled portion in cement concrete 1:2:4 type B1 in wall thickness exc half brick but not exc one brick complete all as specified and directed.

Supply and fix small articles such as bands, straps, supports, hook and pintles, holdfasts and similar articles conforming to Fe 290, Gde E-165 complete all as specified and directed.

Supply and fix 150 mm bore PVC (SWR) pipe, single socketed, in any length with rubber ring joints, fixed to wall complete all as specified.

Supply and fix PVC (SWR) 150mm bore bends any radius complete all as specified and directed.

Supply and fix PVC (SWR)110 mm reducer complete all as specified and directed.

Material and labour for Precast reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in cover slabs of man holes including necessary form work, placed in position, set in CM 1:4 complete all specified and as directed. NOTE: Reinforcement shall be measured and paid separately.

Material and labour for TMT bar 6 to 8mm dia, cut to length, bent to shape required including bending or hooking ends and binding with and including mild steel wire (annealed) not less than 0.9m dia complete as in reinforcement complete all as specified and as directed.

Cleaning the existing drains of clearing all rubbish, silt, vegetation,and waste material from drain removing and depositing the debris to a distance not exceeding 50m all as directed by Engineer-in-Charge. Note:- Rate quoted shall include the removal of drain cover and refixing in the same location after cleaning of drainage.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep in soft/loose soil and getting out including removal of spoil to distance up to 50M complete all as specified and directed.

Material and Labour for red earth/moorum without pebbles obtained from outside MD land, laid in layers not exceeding 15 Cm thick, spreading , levelling watering for planting grass with and including supply and mixing of 0.50Kg/square metre mixutre of cow dung, bone meal, insecticides complete all as specified and as directed.

Material and Labour for digging/excavation of pit of size 30cmx30cmx30cm in loose soil and filling the pits with a mixture of river sand and red earth in the proportion of 1:3 mixed with 2 Kg of cow dung powder, 100 gm of bone meal and 10 gm of insecticide(Furidan) complete all as specified and as directed.

Material and Labour for digging/excavation of pit of size 60cmx60cmx60cm in loose soil and filling the pits with a mixture of river sand and red earth in the proportion of 1:3 mixed with 2 Kg of cow dung powder, 100 gm of bone meal and 10 gm of insecticide(Furidan) complete all as specified and as directed.

Supply and planting red palm sapling having 45 Cm height and shall have growth of 95Cm after 06 months complete all as specified and as directed. NOTE for Item Nos. 5 to 15.02: Contractor shall deploy labour regularly for watering and nursing of all plants up to 24 months from certified date of completion as specified and the quoted rate shall deemed to be inclusive of supply of water.

Supply and planting coconut tree sapling having 75 Cm height and shall have growth of 95Cm after 06 months complete all as specified and as directed.

Supply and planting flower plant sapling having 10Cm minimum height and shall have growth of 30Cm after 06 months complete all as specified and as directed.

Supply and planting Phylanthus sapling having 15Cm to 30 Cm height and shall have growth of 45Cm after 06 months complete all as specified and as directed.

Supply and planting colour flower plant sapling having 15Cm to 30 Cm height and shall have growth of 45Cm after 06 months complete all as specified and as directed.

Supply and planting Song of India flower plant sapling having 15Cm to 30 Cm height and shall have growth of 45Cm after 06 months complete all as specified and as directed.

Supply and planting Dracena flower plant sapling having 15Cm to 30 Cm height and shall have growth of 60Cm after 06 months complete all as specified and as directed.

Supply and planting Mexican grass turfing including manure complete all as specified and as directed.

Material and Labour for preparing the surface of soil by spreading, levelling 10 Cm thick red earth/moorum obtained from outside MD land, laid in layers not exceeding 15 Cm thick, spreading , levelling watering for planting grass with and including supply and laying one layer of pesticides mixed with organic manure in 1:3 proportion and supply and planting Korean grass turfing, well watered and removing weeds etc complete all as specified and as directed.

Material and Labour for digging/excavation of pit of size 30cmx30cmx30cm in loose soil and filling the pits by spreading a mixture of pesticides, organic manure and approved red earth in proportion 1:3:6 for laying border plants like Exora Miniatus, Pilanthus, Allamanda, Heliconia, Ribbon Grass, Lantana, Verbenia of height 45Cm complete all as specified and as directed.

Material and Labour for digging/excavation of pit of size 30cmx30cmx30cm in loose soil and spreading on layer in the pits by spreading a mixture of pesticides, organic manure and approved red earth in proportion 1:3:6 for tree sapling or flower plant and back filling with organic manure, sand and red earth in the ration of 2:3:4 and well watered complete all as specified and as directed for following:- (a) Dacaena Florida beauty 45 Cm height.

(b) Rajamalli 45 Cm height.

(c) Codiuem(Corton) 45 Cm height.

Schedule of Credit (Minus) Rs. 33,925.00 NOTE: Bidder shall insert credit amount of Rs. 33,925.00 as rate in Green field under Col-5.

LAKSHMI BUILDERS

KDR CONSTRUCTION