CERTAIN SPL/PROVISION WORKS AS SPL REPAIR TO BLDG NO T-326 AT 26 RAJPUT, PROVISION OF RECREATION ROOM/PLAYING AREA NEAR OFFRS MESS AT 166 MTN BDE CAMP, PROVN OF GENERATOR SET ROOM/SHED AT MAIN OFFICE AREA /LOC AT 166 MTN BDE CAMP, PROV

Amount

Schedule 'A'

Surface excavation n.exe 30cm deep and average 15cm deep and getting out in soft/loose soil

Dismantling of plain or corrugated steel or AC sheeting, any gauge, or any thickness as in roof coverings including nainital or similar pattern including Ridges/Valley/Hips/ Eaves board complete all as specified and directed.

M&L for high tensile 550 MPA yield strength Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering The sheet shall have a hot dip metallic zinc aluminium alloy coating of zinc 43.5%, aluminium (55%)and silicon (1.5%) with total mass coating of 150 gms/sqm on both sides. Covered width will be 1020mm and sheet length as per site requirement. The profile is having return leg for proper side lap. The sheet shall be fixed using self drilling/self capping screws with EDPM seal complete all as specified and directed.

All as per item above but Plain sheets as in ridges/ hips / valley/Eaves and Eaves board - ditto --

M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate 100 mm thick as in sub base complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in floor finishes 40 mm thick laid in panels & finished even and smooth without using extra cement complete all as specified and directed.

M&L Broken stone or boulders hardcore of gauge exceeding 63 mm but not exceeding 100 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for mild steel work in tubular trusses and tubular posts including special shaped washer duly welded, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St 240 with one shop coat of Zinc Chrome primer paint including preparation of surface at contractor workshop before fabrication complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth for foundation etc. or for shafts, wells cesspits manholes pier holes , cable etc not exceeding 10 sqm on plan and not exceeding 1.5 m depth in soft /loose soil etc complete all as specified and directed

Returning, filing in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in any type of soil etc complete all as specified and directed

Removal of excavated materials not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting points etc complete all as specified and directed

M&L for PCC 1:4:8 Type D2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L for fly ash brick work with old size sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for fly ash brick work with old size sub class 'B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M & L for rendering 20mm thick on brick wall or concrete surface in cement mortar (1:4) consisting two layers, top layer of 10mm thick mixed with water proofing compound, finished even and smooth without using extra cement complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid saperately.)

M&L for preparation of newly plastered surfaces wall and applying two coats of cement base paint complete all as specified and directed.

M&L for preparation of new surface of steel and iron of any discription, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint, white or tinted complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying three coat of white wash complete all as specified and directed.

M&L for PCC 1:2:4 Type B2 using 40mm graded stone aggregate as in foundations, filling and mass concrete, retaining wall, pillers, columns boundary pillar etc complete all as specified and directed.

Cutting holes in brick walls built in cement mortar or cement lime mortar for inserting Hold fasts depth of embedded porton of hold fasts or lugs measured from the face of the jamb into wall exceeding half brick but not exceeding one brick and making good dismantled portion in CM 1:3 or PCC 1:2:4 - B1,using 20 mm graded stoneaggregate complete all as specified and directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing/grills made of hollow tubes, bars, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel hinges, nuts and bolts complete, including fixing the railing/grills with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab, walls with suitable arrangement complete all as specified and directed.

S&F Powder coated anodised aluminium window sliding type three track aluminium sections weighting not less than 0.55 kg per mtr ( Two glazedshutter and one wire mess shutter ) including necessary jointing cleats, glazing cleat, rubber packing anodised aluminium snap gridding, screws, handle clocking arrangement etc complete 5.5 mm thick plain or tinted glass complete all as specified ( Make- Jindal/Hindalco)

Excavating in soft/loose soil for post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,complete all as specified and directed

Dismantling of timber scantling 40 sq cm and over in section, in any position as in framed work complete all as specified and directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed

Demolition of reed, lathing, single or double,including battens and plaster or chicken wire lathing complete all as specified and directed.

Demolition of brick masonary work, built in cement mortar or cement lime mortar including all quions, arches, pillars, etc. but excluding precast concrete articles etc. complete all as specified and directed.

Taking down chowkhats or frames with shutters (without talking off shutters from the freme) area n.exc 1.50 each and removing from site complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) area exc 1.50 and n.exc 4 Sqm each and removing from site complete all as specified and directed.

S&F factory made Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube, supplying and fixing in opening with fittings as per specification & drawing complete all as specified and directed.

S&F, factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain cover PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rails lock rail and bottom rail on either side & as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement and supply & fixing in the frame at site as per specification and shown on drawing SSR Part-II (2004) all as specified complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel 100 mm long complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section 100 mm long complete all as specified and directed.

S&F aluminium handles cast type anodised of 100 mm size complete all as specified and directed.

S&F ventilator tophung shutter including hinges steel peg stay complete all as specified and directed

Taking up or down steel tubing and connections including cleaning if refixing required for 15 mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 20 mm bore of pipe complete all as specified and directed.

S& F 15 mm bore steel water tubes, medium grade, galvanised with all fitings and fixed to wall, complete all as specified and directed.

S& F 20 mm bore steel water tubes, medium grade, galvanised with all fitings and fixed to wall, complete all as specified and directed.

25 mm dia bore Gun mnetal valve complete all as specified and directed

S&F swivel shower roses of PTMT any colour for fixing with shower arm15mm pipe complete all as specified and directed.

S&F of PVC 75 mm bore (SWR) pipes single socket, in any length with rubber ring joint, laid in tranches or in floor,complete all as specified and as directed.

S&F of PVC 110 mm bore (SWR) pipes single socket, in any length with rubber ring joint, laid in tranches or in floor,complete all as specified and as directed.

S&F of PVC (SWR) bend any radius suitable for 75 mm bore PVC pipe jointed with solvent complete all as specified and directed.

S&F of PVC (SWR) bend any radius suitable for 110 mm bore PVC pipe jointed with solvent complete all as specified and directed.

S&F PVC (SWR) junction single, (single T) equal or un equal of 110 mm bore of pipe with access door complete all as specified and directed

M&L PVC (SWR) gully trap 125/110mm setting and jointing with solvant cement complete all as specified and directed

S&F vitreous china EWC white with 'P' or 'S' trap front or back inlet any pattern excluding flushing cistern & flush pipe but including plastic water closet seat black closed pattern with flat bottom and cover and hinging device complete all as specified and directed.

S&F Vitreous china wash basin, white, flat back, size 550 x 400 mm, including pair of brackets and cutting and pinning in ends of brackets,32mm dia CP waste Coupling,32mm dia and 450 mm long Waste pipe, complete all as specified and directed.

S & F in Vitreous China bowl urinal flat back, size of 430 x 370 x 340 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)

S&F PVC 10 litres capacity valveless ,syphonic action type low level flushing cistern ,white including flush pipe, cantilever brackets ,inlet, ball valve, float and handle, etc complete all as specified and directed.

S&F PVC plastic water storage tank capacity 1000 ltr with all neccerry like 20mm boll etc

S&F of PVC Connection pipe 15mm size with PTMT nuts at both ends of length 450mm complete all as specified and as directed.

S&F stop valves fancy type cast copper alloy, chromium plated for 15mm bore pipe, screwed both ends including necessary fittings all complete as specified and as directed.

S & F 15 mm dia bib tap (long body) ( cast copper alloy (fancy type), chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule all as specified and as directed.

S & F 15 mm dia pillar taps ( cast copper alloy (fancy type), chromium plated, screwed down for iron pipe or for brass ferrule all as specified and as directed.

S&F Tubular towel rail of brass chromium plated, 20mm dia, D type, 60cm long between flanges, fixed in repairs complete all as specified and directed.

M&L for 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement and proper bedding and jointing with existing pipe complete all as specified and as directed.

M&L for SGSW drain pipes laid in trenches of 150 mm internal diameter of pipe and jointed as specified complete all as specified and directed.

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate complete all as specified and directed.

M&L for providing RCC (Design Mix) M-25 using 20mm graded stone aggregate as in Rafts, Footings,Foundation, plinth beams, Braces for columns etc complete all as specified and directed. (Note :- Reinforcements and formwork shall be measured and paid separately)

Form work to sides of concrete foundation ,footings, bases of columns, raft and raft beams sides and soffits (if any )of foundation and plinth beams for flat rough finished concrete surface complete all as specified and directed.

M&L for providing RCC (Design MIx) M-25 using 20mm graded stone aggregate as in Beams,Cantilevers,Lintels etc and the like complete all as specified and directed. (Note :- Reinforcements and formwork shall be measured and paid separately)

Use and waste of form work to soffits of floor or roof beam , beam haunching, girders, bressummers, lintels, cantilevers, shelves, for flat rough finished surfaces complete all as specified and directed.

M&L for RCC (Design Mix) M-25 using 20 mm graded stone aggregate as in chajjas and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

Form work to chullah hood, chajjas, troughs and similar items including edges etc for rough finished flat concrete surface complete all as specified and directed.

M&L for TMT bars 10 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for TMT bars 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders , cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Supply only integral water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed.

M&L rendering 10 mm thick in cm 1:6 on fair faces of brick work or concrete surfaces finishing surfaces even and smooth without using extra cement , complete all as specified and as directed.

M&L for mild steel work Hollow section square/rectingular as in roof trusses, purlin , rail etc , complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St 240 with one shop coat of Zinc Chrome primer paint including preparation of surface at contractor workshop before fabrication complete all as specified and as directed.

S&F for Mild steel plates (Plain or chequered) channels,square cut or notched,forming holes with rivetted,bolted or welded attachment conforming to Fe-410-W (Grade E-250) quality A complete all as specified and as directed.

S&F of Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long, Diameter of shank 11 to 15 mm complete all as specified and directed

S&F Rolled mild steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) of grade Fe 410-W (Gde E-250) quality A complete all as specified and directed.

S&F 4mm thick non-Asbestos fibre cement building board( E-board) false ceiling with board of size 600x600mm with powder coated GI snap grid frame work including cutting holes in brick wall built in cement mortar & making good in cement concrete 1:2:4 type B0 Cement mortar 1:3 complete all as specified and directed including all necessary drilling and necessary arrangement to fix electrical items as under:- (a) 27x27x0.55mm thick GI angle powder coated duly plugged @ 600mm centre to centre along perimeter of wall. (b) 25x25x0.55mm thick GI tee powder coated as main and cross runners suspended with 1.6mm dia GI wire suspenders(n.exc 1.2mtr length) with adjustable clamps and dash true fastners plugging in RCC slab/A.I Runner of slopped roof placed @ 600mm centre to centre from perimeter of wall. (c) Fixing of 4mm thick non-Asbestos fibre cement building board( E-board) false ceiling with board of size 600x600mm of approved texture and finished complete with two coats of oil based distemper over a coat of alkali resistance primer on ceiling. NOTE: The complete ceiling work shall be done as per manufactures instruction and as directed.

Demolition of cement concrete un reinforced in ground floor and paving n. exc 15cm thick (below or above ground level) complete all as specified and directed.

S&F joint free non skid Ceramic tiles, coloured, superior quality 7 to 8mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for non skid Ceramic tiles, coloured, superior quality 7 to 8mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm on vertical surface such as dado / skirting / risers to steps etc jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in cement mortor 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured tiles 450 x 350 x 7 mm thick on vertical surface such as dado / skirting / risers to steps etc jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in cement mortor 1:4 complete all as specified and directed.

S&F pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed. NOTE: The quoted unit rate under this item shall deemed to be include one shop coat of primer.

M&L for PCC 1:3:6 type C-1 (using 40mm graded aggregate) as in hold fast block including necessary form work etc complete all as specified and as directed.

S&F 35mm thick factory made, 2nd class hard wood, plain framed, factory made panelled shutter ( two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board Timber flat on both faces, ( feather edged)the size of rail and styles as per IS: 1003 ( Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F of 2nd class hardwood factory made 30 mm thick, glazed and skeleton door shutters, open rebated and prepared to receive glass gauze etc (with sash bars) edges of framing plain, chamfered or rounded materials and revated sash bars any number , edges of framing plain chemfered or rounded fitted with cut and mitred beads for securing glass in door etc or provided with styles and rails as specified in SSR part 1 section 8, clause 8.23 (a) and fitted to chowkats complete all as specified and directed .

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed.

S & f Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or colouredcement to match over 15mm thick screed bed in CM 1:6

S & f Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or colouredcement to match over 10mm thick screed bed in CM 1:6 in vertical srface

Providing and fixing factory made uPVG white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm 52mm), sliding sash (42mm x 67mm). Slidingmesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of wateretc., making arrangement for fixing of hardware.EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated),steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lorpayment purpose.) (A) Area not exceeding 2.00 sqm each ®

S&F steel ventilator with top hung shutter including hinges steel peg stay complete all as specified and directed

S & F Mild steel work in framed work such as in gates,grills, Framed guard bars, gratings, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, and similar work confirming to Fe 290 Gde E-165.complete all as specified and directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and as directed.

S&F 150mm long MS stove enamelled black finished barrel tower bolt of extruded section, fixed with screws complete all as specified and directed.

S&F 250mm long MS stove enamelled black finished, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections suitable for use with pad lock complete all as specified and directed.

S&F 150mm size Aluminium handle,cast type, anodised, fixed with screws complete all as specified and directed.

M&L for preparing of newly plastered surfaces of wall including cornices etc by brooming down applying two coats of antifungal exterior acrylic emulsion paint over a coat of acrylic primer over one coat of wall care putty complete all as specified and directed.

M&L for preparation of newly plastered surfaces wall and applying two coats of oil emulsion Distemper over one coat of cement base putty complete all as specified and directed.

M&L for 75mm thick plain cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection and footpath finished even and smooth without using extra cement, including making joints to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:2 by weight complete all as specified and as directed.

M&L for Precast cement concrete 1:2:4 type B1 using (20 mm graded stone aggregate) lintel up to 1.5 m clear span , cill , steps,copping,kerbs, landings, cover slab (for manholes etc) and similar work including necessary form work and set in CM 1:4 complete all as specified and directed.

INTERNAL ELECTRIFICATION Taking down carefully aluminium conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified.

M&L point wiring complete with FRLS PVC insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including 20mm dia 'medium grade' PVC concealed conduits and fittings, including cutting chasingin brick wall n.exc 10cm width or girth(excluding ceiling surface), pressed steel concealed terminal switch boxes not less than 1.2mm thick of reqd size factory made duly painted inside and outside with two coats of black bituminous paint over one coat red oxide primer, 3mm thick plastic laminated sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories including making good disturbed surfaces with CM(1:4) with treating the surfaces as per existing finishes complete all as specified and directed. (a) One light point controlled by one way switch 5/6 amps.

(b) One ceiling fan/Exhaut fan point controlled by one way switch 5/6 amps.

(c) One socket out let 5/6 amps point on the same board

(d) One socket out let 5/6 amps point on the independent board

(d) One bell/buzer point controlled by one push button on the same board with other switch or independent with cable 1.5sqmm size

All as per item 101 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified and directed.

M&L for point wiring complete for one socket outlet 15 Amps point on independent board with 4 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 4 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated sunken terminal box made out of GI sheet steel not less than 1.22 mm thick for boxes upto a size of 200 x 300mm and above this size not less than 1.63 mm thick duly painted with aluminum inside and anticorrosive paint outside, concealed in walls, with 3mm thick bakelite/plastic laminated sheet top cover fixed with cadmium plated iron screws for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCBs or bus bar shall be done through proper size copper/brass thimbles.

S&F switch piano flush type 5/6 amps single pole one way all as specified.

S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified and directed.

S&F of socket outlet 2 in 1, 5 Pin 5/15 Amp multipurpose 230 volt flush type complete all as specified and directed by Engr-in-Charge.

S&F switch piano flush type 15/16 amps single pole one way complete all as specified and directed.

S&F bell/buzzer push 5/6 amps flush type white/ivory finish complete all as specified and directed.

S&F of call bell ding dong type AC single pole 220/240 Volts surface type complete all as specified and directed.

S&F switch piano flush type 15/16 amps single pole one way complete all as specified and directed.

S&F ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and directed.

M & L for lamp holder, insulated body, with back plate suitable for batten/angle fittings complete all as specified and directed.

S & F deluxe fan Electronic regulator AC 50 Hzs rotary step white/ivory finish complete all as specified and directed.

S & F Wall mounted slim LED batten 20W, with extruded aluminium housing, with integrated LED driver complete all as specified and as directed.

S&F High Power LED street light fitting ,system wattage-35 Watt, made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having IP65 protection and impact resistance of IK07 with 10KV built in surge protection device using 2.5 Sqmm PVC insulated three core copper cable including taking down all as specified and directed.

Supply and fixing LED light fitting mirror type 9/10 Watt with high with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

S&F, IP 20, class I, LED light 1X18 W (or nearest next higher wattage) (4feet), 5700K, wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified. Cat No :- LUMILINEPLUSBS18WLED865SPCSS, Make – Havells or equivalent make of surya/Bajaj

S&Frecessed mounted light (2x2), 36 watt suitable for indore space including provision of 3 core PVC cable copper conductor of size 23/.0076 and making connection complete all as specified and directed Make - Crmpton Cat No- LCTLRP-36-FO-CDL, Phillips , Bajaj and equivalant

Taking down carefully by unscrewing from boards/ outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, and regulators, etc. all as pecified and as directed

Supply and Fixing MCB DB double door, powder coated sheet metal enclosure, 8 way 240 volts grade single pole and neutral with 200 amps rated bus bar,IP 43 protection fixed to wall using nuts & bolts and washer of suitable dia and grouted to wall using suitable gutties complete all as specified and as directed.

S&F MCB triple pole & neutral 40 amp, 415 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F MCB single pole & neutral 6 to 32 amp, 415 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F ( Isolator) singl pole & neutral 40 amp, 415 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F ( Isolator) singl pole 6 to 32 amp, 415 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F MCB single pole, 6 to 32 amps rating, 240 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F ceiling fan complete with blades , downrod , electronic regulator and accessories 230V , 1200mm sweep, Min air delivery 210CFM with service vaalue 6.00 BEE. Five star rated with bushless direct current motor (BLDC)

S&F exhaust fan of 250mm sweep A/C single phase 230/240 volts heavy duty complete with fan motor, blade, bracket and ring including grouting anchor bolts and making good to disturbed surfaces to match the existing complete including provision of PVC insulated & PVC sheathed round flexible cable of copper conductor,Three core of size 0.5 sqmm from ceiling rose to connector of fan, surface of the wall shall be made good by cement work/plastering and matching by existing colour ,all the metal part shall be painted two coats of synthetic enamel paint over a coat of primer, writting the MES no. with white colour paint complete all as specified and directed.

M&L for Earthing complete with galvanised steel plate electrode of size 600x600x6.30mm thick burried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised 4 mm dia earth lead by means of nuts bolts check nuts GI washers earth wire protected by galvanised iron pipe 15mm bore (Light grade) for building LT wall panel all as directed including concrete pit in PCC (1:3:6) type CI, precast RCC cover slab of size 30x30x10 cm with one handle for lifting made out of 8 mm diameter MS bar finnel wire mesh 20 mm bore galvanised iron pipe (medium grade) for watering charcoal or coke and salt in alternate layers necessary earth work in soft/loose soilwith and including taking down the old one complete all as shown in electrical plate No 3 of SSR Part I 2009 including testing on completion all as specified and directed.

S&F sub main wiring concelled type with single core FRLS PVC insulated unsheathed multistranded copper conductor conforming to IS 694 of size 4sqmm nominal cross sectional area,1100 v grade and two run of 4sqmm nominal cross sectional area FRLS PVC insulated unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits and fittings,complete including taking down of old sub main wiring all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

S&F street light bracket, made out of GI pipe medium grade) 25mm bore, 1.2 m long bend to shape and fixing/grouting with wall using 2 Nos 25 x 5 mm size MS FI clamps with bolts, nuts & washers complete including drilling as necessary and two coats of Aluminium paint over a coat of Red oxide primer all as specified & directed.

S&F and testing PVC Insulated screened XLPE Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of of size 16 sqmm 4 core , providing lugs, straight through joints as required complete including jointing material as required and making connection of LT cables , including dismantling & taking out defective LT under ground PVC cable from trenches, cutting and removing defective parts complete all as specified and directed.:- Note:- Excavation & earthwork,sand cushoining,brick protection & GI pipe shall measured and paid separately,

Supply and laying sub class 'B' bricks laid dry and flat across the length of cable for protection of cable complete all as specified and directed

M&L for GI tubing 25 mm bore ,medium class with all necessary fittings laid in trenches complete all as specified and directed.

M&L for GI tubing 40 mm bore ,light grade with all necessary fittings laid in trenches/under road crossing/fixed on pole/wall/under floor including suitable mild steel FI clamps of required size complete all as specified and directed.

M & L for sand cushioning/fdn filling with river Sand to underground cable/fdn (8 cm thick before laying and 15 cm thick after laying the cable/fdn punned to a thickness of 18 cm) complete all as specified and directed

M/S SARDAR MAL NAHATA

M/S BIJAY KUMAR SHIVA

M/S SANMILAN NANDI

M/S RATHIN ENTERPRISES

M/S DEY ENTERPRISE

MAJUMDER ENTERPRISE

M/S. KUMAR CONSTRUCTION CO.