Bagrakote Higher Secondary School

GORKHALAND TERRITORIAL ADMINISTRATION

WEST BENGAL STATE RURAL DEVELOPMENT AGENCY, KALIMPONG DIVISION

District: KALIMPONG

Block: KALIMPONG I

SUMMARY OF COST ESTIMATE

BILL DESCRIPTION COST INCLUDING IGST & LWC (in Rs.)

1 Supply & Fixing louver shutter on wall with necy. bolts & nuts (6 mm dia x 62 mm long)

3 For Al 30 cm Exhaust fan (12")

Rupees Four Crore EightyOne Lakh SeventySix Thousand Three Hundred Fourty Only

WEST BENGAL STATE RURAL DEVELOPMENT AGENCY, KALIMPONG DIVISION

PRICED SCHEDULE

District KALIMPONG

Block KALIMPONG I

Name of Work CONSTRUCTION OF BAGRAKOTE HIGHER SECONDARY SCHOOL IN KALIMPONG I BLOCK, DISTRICT KALIMPONG UNDER RIDF - XXXI

Sl No. Item No Page No Brief Description of Item Quantity Unit Rate (Rs) Amount (Rs)

1. MAIN BUILDING

1.01 Page 1 Item No 2.a Earth work in excavation of foundation trenches or drains in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing,spreading or stacking the spoils within a lead of 75m.as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. Depth of excavation exceeding 1500 mm cum 11927

Page 1 Item No 2.b Earth work in excavation of foundation trenches or drains in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing,spreading or stacking the spoils within a lead of 75m.as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. (b) Depth of excavation for additional depth beyond 1,500 mm. and upto 3,000 mm. but not requiring shoring. cum 19238 Rupees Nineteen Thousand Two Hundred ThirtyEight Only

Page 5 Item No 10 Pre-Constructional Anti-termite measures: (a) Anti termite treatment to bottom surface ( in case of masonry foundation and basements) and the sides (upto a height of 300 mm. from bottom) of the excavation trenches with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight at the rate of 5 Litres per sq. m. area. The work shall be carried out as per specification described in 6.2.1. of code IS- 6313 (part -II) 1981. (Mode of measurment will be the plan area of foundation treated.) 529.13 sqm 111 Rupees One Hundred Eleven Only

Page 1 Item No 3.a Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150mm including watering and ramming etc. layer by layer complete. cum 7754 Rupees Seven Thousand Seven Hundred FiftyFour Only

Page 2 Item no 4.b Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) cum 144111 Rupees One Lakh FourtyFour Thousand One Hundred Eleven Only

Page226 Item No 1 a Brick soling with picked jhama bricks including preparation of bed as necessary with brick joints properly filled in and packed with powdered earth and including necessary cushion of similar material below the soling (and in between layers when more than one layer is used) completes as per direction. (a) Single brick flat soling (thickness 75 mm.) 529.125 sqm 488.4 Rupees Four Hundred EightyEight Paise Fourty Only

Page 34 Item No 22 II (a) Cement concrete with 30mm down graded shingles excluding shuttering. cum 5971.2 Rupees Five Thousand Nine Hundred SeventyOne Paise Twenty Only

Page 25 Item No 6.(ii) Controlled Cement concrete with well graded stone chips (20 mm nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test and job mix foumula. In ground floor and foundation.[using concrete mixture] M 25 Grade (ii ) N.B. Variety (Stone Metal) cum 8187.6 Rupees Eight Thousand One Hundred EightySeven Paise Sixty Only

Page 25 Item No 6.(ii) Controlled Cement concrete with well graded stone chips (20 mm nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test and job mix foumula. In ground floor and foundation.[using concrete mixture] M 25 Grade (ii ) N.B. Variety (Stone Metal) 1st Floor cum 8283.6 Rupees Eight Thousand Two Hundred EightyThree Paise Sixty Only

Page 25 Item No 6.(ii) Controlled Cement concrete with well graded stone chips (20 mm nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test and job mix foumula. In ground floor and foundation.[using concrete mixture] M 25 Grade (ii ) N.B. Variety (Stone Metal) 2nd Floor cum 8379.6

Page 25 Item No 6.(ii) Controlled Cement concrete with well graded stone chips (20 mm nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test and job mix foumula. In ground floor and foundation.[using concrete mixture] M 25 Grade (ii ) N.B. Variety (Stone Metal) 3rd Floor 0.800 cum 8475.6 Rupees Eight Thousand Four Hundred SeventyFive Paise Sixty Only

Page43-44 Item No 40 (a) (i) (I) Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods initial straightening and removal of loose rust (if necessary), cutting to requisite length hooking and bending to correct shape placing in proper position and binding with16G black annealed wire at every intersection as per drawing and direction. (a) For works in foundation and upto roof of ground floor/upto 4 m Ground Floor 0.679 MT 79822.8 Rupees SeventyNine Thousand Eight Hundred TwentyTwo Paise Eighty Only

Page43-44 Item No 40 (a) (i) (I) Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods initial straightening and removal of loose rust (if necessary), cutting to requisite length hooking and bending to correct shape placing in proper position and binding with16G black annealed wire at every intersection as per drawing and direction. (a) For works in foundation and upto roof of ground floor/upto 4 m 1st Floor 0.559 MT 80252.8 Rupees Eighty Thousand Two Hundred FiftyTwo Paise Eighty Only

Page43-44 Item No 40 (a) (i) (I) Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods initial straightening and removal of loose rust (if necessary), cutting to requisite length hooking and bending to correct shape placing in proper position and binding with16G black annealed wire at every intersection as per drawing and direction. (a) For works in foundation and upto roof of ground floor/upto 4 m 2nd Floor 0.719 MT 80682.8 Rupees Eighty Thousand Six Hundred EightyTwo Paise Eighty Only

Page43-44 Item No 40 (a) (i) (I) Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods initial straightening and removal of loose rust (if necessary), cutting to requisite length hooking and bending to correct shape placing in proper position and binding with16G black annealed wire at every intersection as per drawing and direction. (a) For works in foundation and upto roof of ground floor/upto 4 m 3rd Floor MT 81112.8 Rupees EightyOne Thousand One Hundred Twelve Paise Eighty Only

Page47 Item No 1 25mm. thick damp proof course with cement concrete with stone chips (1:1.5:3) [with graded stone aggregate 10 mm nominal size] and admixture of water proofing compound as per manufacturer's specification followed by two coat of polymer based paint, (1st coat after 4 to 5 days of concrete laying and 2 nd coat just before brick masonry work) as directed (cost of water proofing compound & polymer based paint to be paid separately).( Chequering not required over concrete or painted surface). [Note: - Waterproofing as per item 9, polymer based paint as per item 8 (a) of subhead C of Section (C). 50 sqm 270 Rupees Two Hundred Seventy Only

Page 47 Item No 3 Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or infoundation or in foundation trenches. 297.06 sqm 28.8 Rupees TwentyEight Paise Eighty Only

Page 42 Item No 36.c Hire and labour charges for shuttering with centering and necessary staging upto 4m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs,beams,columns,lintels curved or straight including fitting , fixing and striking out after completion of works(upto roof of ground ground floor) (c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work Ground Floor sqm 374 Rupees Three Hundred SeventyFour Only

Page 42 Item No 36.c Hire and labour charges for shuttering with centering and necessary staging upto 4m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs,beams,columns,lintels curved or straight including fitting , fixing and striking out after completion of works(upto roof of ground ground floor) (c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work 1st Floor 1107.17 sqm 392 Rupees Three Hundred NinetyTwo Only

Page 42 Item No 36.c Hire and labour charges for shuttering with centering and necessary staging upto 4m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs,beams,columns,lintels curved or straight including fitting , fixing and striking out after completion of works(upto roof of ground ground floor) (c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work 2nd Floor 798.33 sqm 410

Page 42 Item No 36.c Hire and labour charges for shuttering with centering and necessary staging upto 4m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs,beams,columns,lintels curved or straight including fitting , fixing and striking out after completion of works(upto roof of ground ground floor) (c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work 3rd Floor 322.73 sqm 428 Rupees Four Hundred TwentyEight Only

Page 16 Item no 17 125 mm thick brick work with 1st class bricks in cement morter (1:3) in ground floor 629.36 sqm 1074 Rupees One Thousand SeventyFour Only

Page 16 Item no 17 125 mm thick brick work with 1st class bricks in cement morter (1:3) in ground floor i) 1st Floor 638.35 sqm 1086 Rupees One Thousand EightySix Only

Page 16 Item no 17 125 mm thick brick work with 1st class bricks in cement morter (1:3) in ground floor i) 2nd Floor 581.14 sqm 1098 Rupees One Thousand NinetyEight Only

Page 16 Item No 18 Extra for using approved H.B netting in every third layer in 16 & 17 of subhead A above in any floor 616.28 sqm 50.4 Rupees Fifty Paise Fourty Only

Page 15 Item No 7 Brick work with 1st class bricks in cement mortar (1:4) (a) In foundation and plinth cum 8062.8 Rupees Eight Thousand SixtyTwo Paise Eighty Only

Page 189 Item No 1 (ii) (a) Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (ii) With 1:4 cement mortar (a) 20 mm thick plaster 1771.57 sqm 247.2 Rupees Two Hundred FourtySeven Paise Twenty Only

Page 189 Item No 1 (ii) (a) Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (ii) With 1:4 cement mortar (a) 20 mm thick plaster 1st Floor sqm 251.2

Page 189 Item No 1 (ii) (a) Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (ii) With 1:4 cement mortar (a) 20 mm thick plaster 2nd Floor 0.399 sqm 255.2 Rupees Two Hundred FiftyFive Paise Twenty Only

Page 189 Item No 1 (ii) (b) Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (ii) With 1:4 cement mortar (b) 15 mm thick plaster External Wall 0.799 sqm 211.2 Rupees Two Hundred Eleven Paise Twenty Only

Page 189 Item No 1 (ii) (b) Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (ii) With 1:4 cement mortar (b) 15 mm thick plaster External Wall 1st floor 514.36 sqm 215.2 Rupees Two Hundred Fifteen Paise Twenty Only

Page 189 Item No 1 (ii) (b) Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (ii) With 1:4 cement mortar (b) 15 mm thick plaster External Wall 2nd floor 550.11 sqm 219.2 Rupees Two Hundred Nineteen Paise Twenty Only

Page 64 Item No 35 Supplying, fitting & fixing 1st quality Ceramic tiles in wall sand floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. 0.799 sqm 955.2 Rupees Nine Hundred FiftyFive Paise Twenty Only

Page 54 Item No 17 18 mm. to 22 mm. thick, kota stone slab set in 20 mm thick (avg) cement mortar (1:4) in floor, stair & lobby including pointing in cement slurry with admixture of pigment matching the stone shade, including grinding & polishing as per direction of Engineer - in - charge to match with the existing work. [Slurry for bedding @ 4.4 kg/Sq.m and pointing @2.0 kg/Sq.m] 0.559 sqm 1248 Rupees One Thousand Two Hundred FourtyEight Only

Page 54 Item No 19 Extra cost of labour for grinding Kota Stone Floor in treads and riser of Steps. sqm 1498.8 Rupees One Thousand Four Hundred NinetyEight Paise Eighty Only

Page 280 Item No 1 Supplying and laying true to line and level Anti-Skid, Full Body, Homogeneous & Granular finish Vitrified Tiles conforming to IS:15622-2006 & IS 4457-2007 and testing shall be made in accordance with IS:13630 [Non- modular sizes for tiles with Skid resistance > 0.5, Mohr's hardness > 5.0, Staining resistance: Class-1, Water Absorption: E < 0.5%], MOR > 35 N/sq.mm in Internal area of building e.g. Toilet Block, Passage, Corridor, Accessible Open Terrace etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg./Sqm or using Polymerised Adhesive (6 mm thick layer applied directly over finished artificial stone floor/ Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per Sqm below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles/ epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contractor). sqm 1087.2

Page 54 Item No 20 Supplying, fitting and fixing 18 mm. to 22 mm. thick kota stone slab in wall, dado in 15 mm thick [avg] cement mortar (1:3) including making suitable arrangement to hold the stone properly by brass / copper hooks including pointing in cement mortar (1:2) (1 cement : 2 marble dust) with admixture of pigments matching the stone shade, including grinding and polishing all complete as per direction of Engineer-in-charge including cost of materials, labour, scaffolding, staging, curing complete. [Using cement slurry for bedding @4.4 kg/Sq.m and for jointing @1.8 kg/Sq.m] 0.800 sqm 1408.8 Rupees One Thousand Four Hundred Eight Paise Eighty Only

Page 153 Item No 39 (i) (a) Styles and rails of wooden shutters fitted and fixed complete. (Payment to be made on area of new work only). In Ground Floor: 61.5 sqm 2717 Rupees Two Thousand Seven Hundred Seventeen Only

Page 66 Item No 36 Supplying and laying true to line and level vitrified tiles of approved brand (size not less than 600 mm X 600 mm X 10 mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry back side of tiles using cement @ 2.91Kg./sqM or using polymerised adhesive (6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles / epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contractor 45.66 sqm 2055.6 Rupees Two Thousand FiftyFive Paise Sixty Only

Page 192 Item no 1 Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m. 368.35 sqm Rupees Fourty Paise Eighty Only

Page 114 Item No 1 Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). cum 87544.8 Rupees EightySeven Thousand Five Hundred FourtyFour Paise Eighty Only

Page 114 Item No 1 Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). 1st Floor cum 87744.8 Rupees EightySeven Thousand Seven Hundred FourtyFour Paise Eighty Only

Page 114 Item No 1 Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). 2nd Floor cum 87944.8 Rupees EightySeven Thousand Nine Hundred FourtyFour Paise Eighty Only

Page 41 Item No 31 R.C. weather board (1:1.5:3) with stone chips and necessary reinforcement upto 1% (including main and distribution bars), shuttering and 10 mm. thick cement plaster (1:4) including all moulding, drip course etc. complete in ground floor. 56.7 sqm 1381.2

Page 117 Item No 1 Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor. (In case of non-supply of single plank, penal rate of reduction of 20% will be made) sqm 3346.8 Rupees Three Thousand Three Hundred FourtySix Paise Eighty Only

Page 123 Item No 1 Z-batten shutters of door and window as per design havings tongued and groove half lap jointed as per direction of the Engineer-in-Charge including fitting and fixing shutter in position, but excluding the cost of hinges and other fittings in ground floor. 51.84 sqm 3637.2 Rupees Three Thousand Six Hundred ThirtySeven Paise Twenty Only

Page 124 Item No 11 Supplying solid flush type doors of commercial quality, the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan or similar wood veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fittings in ground floor. (a) 35mm thick shutters (single leaf) 5.04 sqm 4086 Rupees Four Thousand EightySix Only

Page 117 Item no 8 Supplying fitting and fixing in position approved P.V.C. door frame (Matt finish) made of extruded P.V.C. multichamber hollow section having dimensions 60mm x 50mm x 2mm (+/-0.2mm), horizontal section will be joined with vertical section by galvanised steel screws after inserting two number steel brackets as reinforcement making suitable space for placing hinges, one steel tube 40mm x 20mm x 1.20 mm will be inserted on one full vertical side of the frame (hinge side) as reinforcement, the frame will then be fixed in the opening with the help of P.V.C. expandable fastner/wooden gutties and galvanised steel screws including cost of all materials and labour, hire charges of tools and appliances, carriage of all materials, taxes and all other incidental charges complete. sqm 342 Rupees Three Hundred FourtyTwo Only

Page 126 Item No 16 Supplying, Fitting & Fixing 30 mm thick both side prelaminated Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in- Charge. sqm 3058.8 Rupees Three Thousand FiftyEight Paise Eighty Only

Page 140 Item No 4 Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately) (b) 40mm X 6mm, 200mm Length Each 31.2 Rupees ThirtyOne Paise Twenty Only

Page 145 Item No 29 Anodised aluminium butt hinges of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 205/66) and fitted and fixed with cadmium plated screws: (iv) 75 x 63 x 3.2mm. Each Rupees SeventyFive Paise Sixty Only

Page 145 Item No 29 Anodised aluminium butt hinges of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 205/66) and fitted and fixed with cadmium plated screws: (viii) 125 x 63 x 4.0mm. Each

Page 144 Item No 26 Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: (iv) 150mm long x 10mm dia. bolt. 160 Each 78 Rupees SeventyEight Only

Page 144 Item No 26 Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: vi) 200mm long x 10mm dia. bolt. 116 Each 94.8 Rupees NinetyFour Paise Eighty Only

Page 145 Item No 28 Anodised aluminium Aldrop / Sliding bolts of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 2681/66) fitted and fixed complete. (i) 250mm x 16mm dia bolt. 55 Each 282 Rupees Two Hundred EightyTwo Only

Page 145 Item no 30 Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete: (v) 125 mm grip x 12 mm dia rod. 140 Each 150 Rupees One Hundred Fifty Only

Page 145 Item no 30 Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete: (vi) 150 mm grip x 10 mm dia rod. 98 Each Rupees One Hundred ThirtyNine Paise Twenty Only

Page 101 Item No 2A M.S. structural works with hollow sections (square or rectangular shape) conforming to IS: 806-1968 & IS:1161-1998) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete.The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete. i) For roof truss works a) Span up to 12 Mtr MT

Page 24 Item No 4 Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mmnominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes. cum 6370.8 Rupees Six Thousand Three Hundred Seventy Paise Eighty Only

Page 82 Item No 14 Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work). i) In Roof:- a) With 0.80 mm thick sheet 792.34 sqm 1087.2 Rupees One Thousand EightySeven Paise Twenty Only

Page 84 Item no 18 Aluminium sheet ridging fitted with self tapping screws, EPDM washers etc complete.(Minimum 225mm end lapping). (A) 300 mm lapping each way (b) With 0.91 mm sheet 98 m 576 Rupees Five Hundred SeventySix Only

Page227 Item No 5 Expansion joint in floor roof etc. formed with V strips made of 22.5 cm wide strips of 24 gauge aluminium sheets with anchor arm projecting on each side (and end turned ) embedded in adjacent cement concrete, including shaping and finishing the edges on either side of the joint (including the cost of bituminous filler if any) complete as per direction of Engineer-in-Charge. 30 m 408 Rupees Four Hundred Eight Only

Page 104 Item No 13 (a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. (i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr. Ground floor Qntl 10593.6 Rupees Ten Thousand Five Hundred NinetyThree Paise Sixty Only

Page 104 Item No 13 (a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. (i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr. 1st Floor Qntl 10699.54 Rupees Ten Thousand Six Hundred NinetyNine Paise FiftyFour Only

Page 104 Item No 13 Supplying & Fixing 240 V AC Buzzer (Ancho) on HW board incl. S&F HW board Qntl 10806.54 Rupees Ten Thousand Eight Hundred Six Paise FiftyFour Only

Page 107 Item No 20 Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening if required, fixing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing. (a) Fixed type steel windows as per IS sizes with horizontal glazing bars. Ground Floor 5.04 sqm 1492.8 Rupees One Thousand Four Hundred NinetyTwo Paise Eighty Only

Page 107 Item No 20 Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening if required, fixing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing. (a) Fixed type steel windows as per IS sizes with horizontal glazing bars. 1st Floor 5.04 sqm 1510.71

Page 107 Item No 20 Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening if required, fixing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing. (a) Fixed type steel windows as per IS sizes with horizontal glazing bars. Steel Window sqm 1528.84 Rupees One Thousand Five Hundred TwentyEight Paise EightyFour Only

Page 107 Item No 20 Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening if required, fixing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing. (b) Openable steel windows as per IS sizes with side hung shutters and horizotal glazing bars. [The extra rate admissible for the openable portion only] Ground Floor 12.42 sqm 2060.4 Rupees Two Thousand Sixty Paise Fourty Only

Page 107 Item No 20 Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening if required, fixing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing. (b) Openable steel windows as per IS sizes with side hung shutters and horizotal glazing bars. [The extra rate admissible for the openable portion only] 1st Floor 11.88 sqm 2085.12 Rupees Two Thousand EightyFive Paise Twelve Only

Page 107 Item No 20 Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening if required, fixing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing. (b) Openable steel windows as per IS sizes with side hung shutters and horizotal glazing bars. [The extra rate admissible for the openable portion only] 2nd Floor 5.94 sqm 2109.85 Rupees Two Thousand One Hundred Nine Paise EightyFive Only

Page 206 Item No 7 Supplying, fitting and fixing in position fibre glass panes of approved quality with resin, nail, clip etc. as per IS:12866-1989. (In all floors for internal wall & upto 6 m height for external wall) (c) 2.0 mm thick (3.36 Kg/Sq.m) 29.16 sqm Rupees One Thousand One Hundred ThirtySeven Paise Sixty Only

Page 206 Item No 7 Supplying, fitting and fixing in position fibre glass panes of approved quality with resin, nail, clip etc. as per IS:12866-1989. (In all floors for internal wall & upto 6 m height for external wall) (e) 4.0 mm thick (6.72 Kg/Sq.m) 29.16 sqm Rupees Two Thousand SeventySeven Paise Twenty Only

Page 200 Item No 1 (b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. 384.84 sqm 45.6 Rupees FourtyFive Paise Sixty Only

Page 200 Item No 2 (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (a) On timber or plastered surface : With other than hi-gloss of approved quality- (iv) Two coats (with any shade except white) sqm 90 Rupees Ninety Only

Page 198 Item No 5 Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) Interior Ground Floor 186.18 sqm 146.4

Page 198 Item No 5 Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) Interior 1st Floor 0.799 sqm 146.4 Rupees One Hundred FourtySix Paise Fourty Only

Page 198 Item No 5 Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) Interior 2nd Floor 1021.815 sqm 146.4 Rupees One Hundred FourtySix Paise Fourty Only

Page 198 Item No 5 Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) Exterior Ground Floor 732.27 sqm 146.4 Rupees One Hundred FourtySix Paise Fourty Only

Page 198 Item No 5 Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) Exterior 1st Floor 732.27 sqm 147.12 Rupees One Hundred FourtySeven Paise Twelve Only

Page 198 Item No 5 Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) Exterior 2nd Floor 732.27 sqm 147.84 Rupees One Hundred FourtySeven Paise EightyFour Only

Page 198 Item No 5 Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) Exterior 3rd Floor 35.4375 sqm 148.56 Rupees One Hundred FourtyEight Paise FiftySix Only

Page 195 Item No 7 Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor) (b) Two Coats i) Water based interior grade Acrylic Primer sqm 5412 Rupees Five Thousand Four Hundred Twelve Only

Page 196 Item No 10 Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface. Two Coats 0.800 sqm 85.2 Rupees EightyFive Paise Twenty Only

Page 201 Item no 4 Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) 468.42 sqm 84 Rupees EightyFour Only

Page 45 Item no 8 (a) Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer's specification [Cement to be supplied by the Department] Ground Floor 805.2 sqm 108 Rupees One Hundred Eight Only

Page 45 Item no 8 (a) Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer's specification [Cement to be supplied by the Department] 1st Floor 874.5 sqm 108 Rupees One Hundred Eight Only

Page 45 Item no 8 (a) Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer's specification [Cement to be supplied by the Department] 2nd Floor 874.5 sqm 108 Rupees One Hundred Eight Only

Page 196 Item No 8 Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (b) Two Coats Ground Floor 0.8000 %sqm 5520 Rupees Five Thousand Five Hundred Twenty Only

Page 196 Item No 8 Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (b) Two Coats 1st Floor 0.8000 %sqm 5591 Rupees Five Thousand Five Hundred NinetyOne Only

Page 196 Item No 8 Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (b) Two Coats 2nd Floor 0.8000 %sqm 5662

Page 197 Item No 17 Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. Ground Floor 805.2 sqm Rupees EightyOne Paise Sixty Only

Page 197 Item No 17 Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. 1st Floor 874.5 sqm 82.31 Rupees EightyTwo Paise ThirtyOne Only

Page 197 Item No 17 Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. 2nd Floor 874.5 sqm 83.02 Rupees EightyThree Paise Two Only

Page 200 Item No 1a (a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. 0.199 sqm 36 Rupees ThirtySix Only

Page 200 Item No 3 (B) (B) Painting with superior quality aluminium paint of approved make and brand including smoothening surface by sand papering etc. on steel surface : (b) Two coats sqm Rupees SixtyNine Paise Sixty Only

Page 165 Item No 18 P.V.C- False Ceiling : Providing False Ceiling made with framework of steel tube of 40mm x 20mm of not less than 18 gauge,the long and cross section will be welded with each other 1000mm to 1200mm apart the entire framework will be fixed in wall using rawlplug or gutties or screws etc. and suspended from ceiling with M.S flat 19mmx3mm as necessary,the entire frame will be painted with red oxide. PRINTED LAMINATED P.V.C Section 150mm x 12mmx 1.00mm (+/- 0.01mm) of approved quality and colour will be fixed on the frame so that the entire framework will not be visible from below P.V.C Section will be fixed with the frame with the help of self tapping steel screws including all materials and labour charges including fitting,fixing the same and hoisting including mending the damages in all respect and cost of paint as required as per direction of Engineerin- Charge . In ground floor. 0.600 sqm 1747.2

Page 82 Item No 11 Galvanised iron sheet eaves gutter fitted and fixed withnecessary 50 mm X 6 mm M.S flat bar clamps bent to design, bolts, nuts, washers etc. complete. Eaves gutter made of 0.63 mm. sheets.(300mm End lapping) (a) 225 mm. wide gutter 200 m 418.8 Rupees Four Hundred Eighteen Paise Eighty Only

Page 138 Item No 9 Wooden eaves board as per design, fitted and fixed complete:In ground floor i) Plain eaves board (Local Sal) (a) 19mm thick 50 sqm 1749.6 Rupees One Thousand Seven Hundred FourtyNine Paise Sixty Only

Page 106 Item No 18 Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x 10mm x 2mm vertical channels 100mm apart in fully stretched position 20mm x 5mm M.S. flats as collapsible bracings properly rivetted and washered including 38mm steel rollers including locking arrangements, fitted and fixed in position with lugs set in cement concrete and including cutting necessary holes, chasing etc. in walls, floors etc. and making good damages complete. (Add extra @ 1% for each addl. floor upto 4th floor and @ 1.25% for each addl. floor above 4th floor) In ground floor. 0.000 sqm 5271.6 Rupees Five Thousand Two Hundred SeventyOne Paise Sixty Only

Page 144 Item No 25 Supplying anodised aluminium catch hook with eye fitted and fixed to shutter and chowkat complete of best quality: (ii) 225mm long. 126 Each 52.8 Rupees FiftyTwo Paise Eighty Only

Page 40 Item No 30 Supplying, fitting and fixing Fan Hook for ceiling with 1 metre long 16mm. dia rod complete including mending damages. Payment for damage and repair to be made separately. 50 Each 120 Rupees One Hundred Twenty Only

WEST BENGAL STATE RURAL DEVELOPMENT AGENCY, KALIMPONG DIVISION

PRICED SCHEDULE

District KALIMPONG

Block KALIMPONG I

Name of Work CONSTRUCTION OF BAGRAKOTE HIGHER SECONDARY SCHOOL IN KALIMPONG I BLOCK, DISTRICT KALIMPONG UNDER RIDF - XXXI

Sl No. Item No Page No Brief Description of Item Quantity Unit Rate (Rs) Amount (Rs)

2. SANITARY & PLUMBING

Page 87 Item No 1.(ii) Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling, 15 mm thick (1:4) cement plaster to inside walls and out-side walls upto G.L. and 20 mm.thick (1:4) plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (1:4) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials. 4 Each

Page 88-89 Item No 3.ii.B Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C(1:1.5:3) bottom slab including supplying, fitting and fixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and fefilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. Note:- (i) Finished level of Septic Tank should be 400 mm. from Ground Level. (ii) Height of 50 mm. Ventilation pipe &Mosquito proof mesh, should be follwed as per IS:2470,Part- I.Payment will be made separetly on the basis of actual height based on relevant I.S.Code. 2 Each 119229.6 Rupees One Lakh Nineteen Thousand Two Hundred TwentyNine Paise Sixty Only

Page 89 Item No 4(iii) Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) to inside face upto the depth of cement brick work, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials.With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00m inside dia. 3 Each 22987.2 Rupees TwentyTwo Thousand Nine Hundred EightySeven Paise Twenty Only

Page 79 Item No 4 Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing). (i) 580 mm X 440 mm 16 Each 1935.6 Rupees One Thousand Nine Hundred ThirtyFive Paise Sixty Only

Page 79 Item No 1 Supplying, fitting and fixing Shallow water closet Indian pattern (I.P.W.C.) of approved make in white vitreous chinaware in position (excluding cost of concrete for fixing). (i) 580 mm long 8 Each Rupees One Thousand One Hundred SixtySeven Paise Sixty Only

Page 79 Item No 3 Supplying, fitting and fixing Anglo-Indian W.C. in white glazed vitreous china ware of approved make complete in position with necessary bolts, nuts etc. b) With 'S' trap (with vent) 8 Each 3944.4 Rupees Three Thousand Nine Hundred FourtyFour Paise Fourty Only

Page 79 Item No 2 Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc. (b) With 'S' trap 8 Each 1814.4 Rupees One Thousand Eight Hundred Fourteen Paise Fourty Only

Page 80 Item No 6 Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete. (i) 635 mm X 395 mm X 420 mm 16 Each 3442.8 Rupees Three Thousand Four Hundred FourtyTwo Paise Eighty Only

Page 80 Item No 7 Supplying, fitting and fixing Squating plate with integral flushing in white vitreous chinaware of approved make in cement concrete (6:3:1) with jhama chips complete. (Payment of concrete will be paid seperately). (i) 450 mm X 350 mm 16 Each 1057.2 Rupees One Thousand FiftySeven Paise Twenty Only

Page No 10 Item No 15 Supplying, fitting and fixing self closing C.P. water tap of approved brand and make - 15 mm dia. 32 Each

Page 29 Item No 1 Supplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. (a) For Exposed Work (b) For Concealed Work 25 mm 1100 m 282 Rupees Two Hundred EightyTwo Only

Page 29 Item No 1 Supplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. (a) For Exposed Work (b) For Concealed Work 20 mm 800 m 342 Rupees Three Hundred FourtyTwo Only

Page 36 Item No 1 Supplying, fitting and fixing 10 litre porcelain low-down cistern of approved make with either side or bottom inlet, side overflow, brackets complete with all internnal PVC fittings. White 32 Each 2756.4 Rupees Two Thousand Seven Hundred FiftySix Paise Fourty Only

Page 37 Item No 6 Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer (b) 1000 litre capacity 5 Each 6153.6 Rupees Six Thousand One Hundred FiftyThree Paise Sixty Only

Page 41 Item No 2 Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint (iii) 630 mm X 450 mm size 25 Each 3912 Rupees Three Thousand Nine Hundred Twelve Only

Page 43 Item No 10 Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps. (iii) 900 mm long 20 Each 90 Rupees Ninety Only

Page 60 Item No 1 Supplying, fitting & fixing Cast iron soil pipe only conforming to I.S. 3989/ 2009 and I.S. 1729/2002 with bobbins, nails etc. including making holes in the wall, floor etc. and cutting trenches etc. in any floor through masonry concrete, if necessary, and mending good damages with necessary jointing materials and painting two coats to the exposed surface with approved paint complete. (Measurement will be made along the center line of the total pipe line in fitted condition including specials,payment for specials & Painting will however be paid seperately). (a) With valamoid joints including sealing with sand cement morter (4:1) upto quarter depth. (ii) 100 mm dia. (internal) 200 m 825.6 Rupees Eight Hundred TwentyFive Paise Sixty Only

Page 82 Item No 19 Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm 20 Each 735.6 Rupees Seven Hundred ThirtyFive Paise Sixty Only

Page No 5 Item No 5 Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only). (iv) 50 mm dia 4 Each 2732.4

Page No 5 Item No 5 Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only). (iv) 25 mm dia 6 Each 933.6 Rupees Nine Hundred ThirtyThree Paise Sixty Only

Page No 5 Item No 5 Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only). (iv) 20 mm dia 40 Each 724.8 Rupees Seven Hundred TwentyFour Paise Eighty Only

Page No 5 Item No 5 Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only). (iv) 15 mm dia 8 Each 525.6 Rupees Five Hundred TwentyFive Paise Sixty Only

Page 41 Item No 3 Supplying, fitting and fixing pedestal of approved make for wash basin (white) 20 Each 1796.4 Rupees One Thousand Seven Hundred NinetySix Paise Fourty Only

Page 45 Item No 19 Supplying, fitting and fixing pillar cock of approved make. a) (i) CP Pillar Cock - 15 mm. (Equivalent to Code No. 507 & Model -Tropical / Sumthing Special of ESSCO or similar brand). 20 Each 666 Rupees Six Hundred SixtySix Only

Page 45 Item No 19 Supplying, fitting and fixing pillar cock of approved make. c) CP Pillar Cock - 15 mm. (Code No. 5011 & Model - FLORENTINE of JAQUAR or equivalent). 6 Each Rupees One Thousand TwentyEight Paise Fourty Only

Page 6 Item No 7 Supplying, fitting and fixing bib cock or stop cock. (a) (i) Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand). 20 Each Rupees Six Hundred FourtySix Paise Eighty Only

Page 6 Item No 7 Supplying, fitting and fixing bib cock or stop cock. (b) (i) Chromium plated Stop Cock (Equivalent to Code No. 513(A) & 513(B) & Model - Tropical / Sumthing Special of ESSCO or similar 20 Each 591.6 Rupees Five Hundred NinetyOne Paise Sixty Only

Page No 81 Item No 11 Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete. i) Polythene Flush Pipe 20 Each 186

Page 53 Item No 12 Supplying,fitting and fixing check valve (horizontal) G.M. tested to 21 kg per sq. cm. (v) 40 mm 20 Each 1776 Rupees One Thousand Seven Hundred SeventySix Only

Page 82 Item No 18 Supplying, fitting and fixing soap holder. (a) PTMT (Prayag or equivalent) 20 Each 162 Rupees One Hundred SixtyTwo Only

Page 3 Item No 2 Supplying, fitting and fixing in position G.I. pipes of TATA make for underground works with all necessary accessories,specials viz.socket, bend, tee, union, cross, elbow, nipple, short piece etc.including cost of all materials,jointing materials ,cutting pipes,making threads,cutting trenches upto 1.5 metre below surface in all sorts of soil and refilling the same as directed with two coats of painting on G.I. pipes and specials with bituminous paint complete in all respect. (Payment will be made on the centre line measurement of the total pipe line including all specials No separate payment will be made for accessories, specials.Payment for painting will be made seperately) (iii) 25 mm dia. medium quality 1200 m 382.8 Rupees Three Hundred EightyTwo Paise Eighty Only

Page 65 Item No 14 Supplying,fitting and fixing cast iron 'P' or 'S' trap conformimg to I.S. 3989/ 2009 and 1729/ 2002 including lead caulked joints and painting two coats to the exposed surface. (Painting to be paid seperately). (B) 'S' Trap (iii) 100 mm 10 Each 963.6 Rupees Nine Hundred SixtyThree Paise Sixty Only

Page 65 Item No 14 Supplying,fitting and fixing cast iron 'P' or 'S' trap conformimg to I.S. 3989/ 2009 and 1729/ 2002 including lead caulked joints and painting two coats to the exposed surface. (Painting to be paid seperately). (A) 'P' Trap (iii) 100 mm 10 Each Rupees One Thousand One Hundred ThirtySeven Paise Sixty Only

Page 12 Item No 19(i) Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (a) For Exposed Work 20 mm 200 m Rupees One Hundred FiftyFour Paise Eighty Only

Page 12 Item No 19(i) Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (a) For Exposed Work 25 mm 200 m 212.4 Rupees Two Hundred Twelve Paise Fourty Only

Page 12 Item No 19(i) Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (a) For Exposed Work 100 mm 700 m 1360.8 Rupees One Thousand Three Hundred Sixty Paise Eighty Only

Page 12 Item No 19(i) Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (b) For Concealed Work 20 mm 200 m 189.6 Rupees One Hundred EightyNine Paise Sixty Only

Page 12 Item No 19(i) Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (a) For Exposed Work 25 mm 200 m 246 Rupees Two Hundred FourtySix Only

Page 44 Item No 35 (MED)(WB)/ELECTRICAL AND MECHANICAL WORKS Supplying and fixing of 2 HP Centrifugal Monoblock pump Make-KSB, AGRIBLOC 20-5050 2 m 12803 Rupees Twelve Thousand Eight Hundred Three Only

TOTAL COST FOR ROAD FURNITURE WORKS

WEST BENGAL STATE RURAL DEVELOPMENT AGENCY, KALIMPONG DIVISION

PRICED SCHEDULE

District KALIMPONG

Block KALIMPONG I

Name of Work CONSTRUCTION OF BAGRAKOTE HIGHER SECONDARY SCHOOL IN KALIMPONG I BLOCK, DISTRICT KALIMPONG UNDER RIDF - XXXI

Sl No. Item No Page No Brief Description of Item Quantity Unit Rate (Rs) Amount (Rs)

3. PROTECTION WALL, DISMANTLING, DRAIN AND LAND DEVELOPMENT

3.01 Page No 11 Item No 8 Taking out carefully G.C.I. or C.I. or asbestos sheets (including ridges etc.) from roof or wall after unscrewing bolts, nuts, screws etc.and stacking the material at site as directed. 730.25 cum 41 Rupees FourtyOne Only

Page No 13 Item No 19 Dismantling carefully wood work in posts, postplates, rafters, partition etc., sorting and stacking serviciable materials at site and removing rubbish as directed. 11.315 cum 278

Page No 10 Item No 1 Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. Block B Side Ground Floor cum 447 Rupees Four Hundred FourtySeven Only

Page No 10 Item No 1 Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. Block B Side 1st Floor cum 497 Rupees Four Hundred NinetySeven Only

Page No 10 Item No 1 Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. Block A Side cum 447 Rupees Four Hundred FourtySeven Only

Page No 10 Item No 3 Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars. Block B Side Ground Floor 181.355 cum 1956 Rupees One Thousand Nine Hundred FiftySix Only

Page No 10 Item No 3 Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars. Block B Side 1st Floor 109.11 cum 2006 Rupees Two Thousand Six Only

Page No 10 Item No 3
Dismantling R.C. floor, roof, beams etc. includin 124.6425 cum 1956 Rupees One Thousand Nine Hundred FiftySix Only

4 way Supplying & Fixing double -door SPN MCB Distribution Board wtih IP-42/43 protection, concealed in wall after cutting the wall & mending good the damages to original finish inc.inter connection with suitable size of copper wire and neutral link & provision for earthing attachment legrand. cum 1417 Rupees One Thousand Four Hundred Seventeen Only

(2+8way) enclosure Supplying and fixing MCB SS enclosure with IP 20/30 Protection, powder coated provison for two-four pole MCB, concealed in wall after cutting the wall and mending good the damages to original fin9ish incl. painting , connection and provision for earthing attachment Single Pole 6-32A MCB 11927 Rupees Eleven Thousand Nine Hundred TwentySeven Only

Double Pole 40A MCB Isolator Double Pole 32A MCB Isolator 0.25 Single Pole 6-32A MCB 7754 Rupees Seven Thousand Seven Hundred FiftyFour Only

Double Pole 40A MCB (For Panel) Supplying, fixing, testing and commissioning wall floor mounted LT Panel primer coated paint and provided with required gasket for dust/vermin proof with degree of protection IP42 suitable for 415 Volt 3 phase 50Hz 4 wire system fabricated out of CRCA sheet up to 2 mm thick (1.6 mm for doors) duly compartentalized for incorner, bus section, outgoings, cable alleys, & CT, PT Ampere, Volt selector switches frequency, phase indicating lamp, Enegergy complete plates 2 earthing terminals, internal wiring and fixing seperately supplied MCBS, MCCBs, ACB panel mounted changeover switch/ SFUs etc as required but excluding cost of busbar strips, Ampere, Volt, selector switch as per approved design and specification. cum 5971.2

Kg Supply and fixing of LT panel accessories of approved make in existing LT panel including connections etc. as required as per specification. 30 sqm 386 Rupees Three Hundred EightySix Only

Supply of 3 Ph LED Ammeter CI 0.5 Supply of copper busbar for electrical power distribution 59.25 cum 6370.8 Rupees Six Thousand Three Hundred Seventy Paise Eighty Only

Supply of ammemeter selector switch current in Each phase with OFF, 4 pos 90 angle of throw (OFF-R-Y-B) Supplying of voltmeter selector switch Votage between phases with OFF, 4 pos 90 angle of throw (OFF-R-Y-B) 36.9375 cum 8187.6 Rupees Eight Thousand One Hundred EightySeven Paise Sixty Only

Supplying of 22.5 mm dia LED indicating lamps Suply of indoor tape insulated ring type low tension current transformer of following rating 100/5A 5VA, CI 1.0 0.119 MT 79822.8 Rupees SeventyNine Thousand Eight Hundred TwentyTwo Paise Eighty Only

Supplying and fixing 415V, TPN SFU open execution in existing SS enclosure/ cubical with nuts bolts etc. incl. S & F 3 nos. DIN type HRC fuse as per rating. 12SA l&T Supplying & fixing s 240V, Modular Socket (2 Module)type fan regulator (Step type) (Brand aprroved by EIC) on existing Modular GI switch board with top cover plate incl. making necy. Connections etc. 511.05 sqm 334 Rupees Three Hundred ThirtyFour Only

Supplying and fixing 415V, TPN on load front operated Changeover switch open execution type in SS enclosure/cubical with nuts bolts etc. 125A L&T Supplying & Fixing of Box type fan clamp of 150mm dia & 80mm depth made of 16 SWG CRCA sheet with one end duly sealed by cover, properly welded, incl. S&F 12mm dia 600mm long MS rod duly bent by heat treatment at the centre position of rod to grip fan bobbin properly, incl. binding the rod and fan box with reinforcement by 22 SWG steel binding wire, incl. supplying & covering the box with alkathene sheet, placed in order to prevent concrete from entering the box. 285 sqm 211.2 Rupees Two Hundred Eleven Paise Twenty Only

Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc. incl. S&F connecting wire for down rod upto 30 cm incl. painting the rod with approved paint and making necessary connection as required by 2x1.5 sqmm flexible copper wire. Fixing only exhaust fan after making hole in wall and making good damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection for exhaust of following diameter: 285 sqm Rupees Fourty Paise Eighty Only

(b) 30 cm (12") Fixing only cabin fan on wall/ceiling by S&F rag bolts, nuts & washers (6 mm dia x 62 mm long) or as reqd. incl. S&F 24/0.20 PVC insulated flexible copper wire 0.5 mt. length 1345 cum 166 Rupees One Hundred SixtySix Only

TOTAL COST FOR LAND DEVELOPMENT WORKS

WEST BENGAL STATE RURAL DEVELOPMENT AGENCY, KALIMPONG DIVISION

PRICED SCHEDULE

District KALIMPONG

Block KALIMPONG I

Name of Work CONSTRUCTION OF BAGRAKOTE HIGHER SECONDARY SCHOOL IN KALIMPONG I BLOCK, DISTRICT KALIMPONG UNDER RIDF - XXXI

Sl No. Brief Description of Item Quantity Unit Rate (Rs) Amount (Rs)

4. ELECTRICAL WORKS

4.01 Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polythen pipe complete with all accessories embedded in wall to light/fan/call bell points with Modular type switch (Brand approved by EIC) fixed on Modular GI switch board with top cover plate flushed in wall incl. mending good damages to original finish. 2x22/0.3 (Ph. & N) and 1x22/0.3 as ECC

a Supply & Delivery of Sweep 48" (1200,mm) AC ceiling fan, 50-70 watts, Speed :->=220 CMM, make (Orient PSPO NEWBREESE or SUMMERCOOL / equivalenr of EPC or USHA STRIKER PLUS or CROMPTON) ( Approved by EIC) 150 Pts Rupees One Thousand One Hundred FourtyOne Paise NinetyFive Only

b Suppl & Delivery Supply and delivery of Wall fan 16" Sweep metal blade a) Crompton Greaves make 150 Pts Rupees One Thousand Two Hundred FiftySix Paise NinetyFive Only

c Supply and delivery of 230V, 50HZ Heavy duty Metal 9" Exhaust ran (EPC/Orient/Usha) 60 Pts Rupees One Thousand Three Hundred SeventyOne Paise NinetyFive Only

Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) of the following sizes in the prelaid polythene pipe and by the prelaid GI fish wire and making necy. connection as required

a Siupply and delivery of 230V, 50Hz Heavy duty Metak 12" Exhausr Fan (EPC/Orient/USHA) 200 RM Rupees FiftyFive Paise Twenty Only

b 2 x 36/0.3 (2.5 sqmm) 300 RM Rupees SeventyFour Paise SeventyFive Only

c 2 x 56/0.3 (4 sqmm) [Power & 20A Board] 120 RM Rupees One Hundred Nine Paise TwentyFive Only

d 2 x 84/0.3 (6 sqmm) [Main Panel to Floor wise SPN DB] 300 RM Rupees One Hundred FiftyNine Paise EightyFive Only

4.03 Laying through Floor/ Pavement/Wall

Laying of cable as below, after cutting floor/pavement/wall/ and making holes incl., embedding the cable at an average depth as below and mending good the damages to original finish incl.mremoving the rubbish 620 RM Rupees FourtyOne Paise Fourty Only

Laying through Underground Trech 300 RM Rupees FiftySix Paise ThirtyFive Only

4.03 Laying of one No. cable above 35 sqmm and upto 185 sqmm in underground trench 460mm wide x 760mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per Mtr. including filling the space between the bricks and cable and also the trenchwith shifted soil, leveling up and restoring surface duly rammed

Finishing of the PVC insulated wire ends by socketting with pin/ ring type copper sockets and insulated tapes etc., including supplying sockets, tapes. 620 RM Rupees SixtyNine Only

4.03 For 2 core upto 4 sqmm

For 2 core upto 10 sqmm 300 RM Rupees EightyEight Paise FiftyFive Only

4.04 Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polythen pipe complete with all accessories embedded in wall to light/fan/call bell points with Modular type switch (Brand approved by EIC) fixed on Modular GI switch board with top cover plate flushed in wall incl. mending good damages to original finish. 2x22/0.3 (Ph. & N) and 1x22/0.3 as ECC

a 6 sqmm 20 Pts Rupees Two Hundred EightySix Paise ThirtyFive Only

4.05 Supplying & Fixing GI Modular Switch Board of the following sizes complete with three no. suitable size Copper bar with holes (for Ph, N & E) fixed on bakelite/Hard Rubber insulator over the MS welded chairs incl. top cover flushed in wall for housing the board after cutting the brick wall incl. making earthing attachment, painting and mending good damages to building works.

a 4 Module 5 Each

b 6 Module 5 Each Rupees Three Hundred EightyOne Paise Eighty Only

4.05 2.5 sqmm 20 Each Rupees NinetyFour Paise Thirty Only

4 sqmm 18 Each Rupees One Hundred ThirtySix Paise EightyFive Only

4.07 40 mm dia ISI 10 Each Rupees One Hundred ThirtyEight Only

4.08 Supply & Fixing 240 V, 16 A, 3 pin Modular type plug socket (Brand approved by EIC) with 16A Modular type switch, without plug top on 4 Module GI Modular type switch board with top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. 6 Each Rupees One Hundred EightySix Paise Thirty Only

4.09 SUPPLYING OF FOLLOWING XLPE INSULATED ALUMINIUM CONDUCTOR ARMORED CABLES OF 1.1KV GRADE AS PER IS 7098 (PART 1) 1988 WITH UP TO DATE AMMENDMENTS 4 Each Rupees Two Hundred TwentyFour Paise TwentyFive Only

Supply & Fixing 240 V, 16 A, 3 pin Modular type plug socket (Brand approved by EIC) with 16A Modular type switch, without plug top on 4 Module GI Modular type switch board with top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. 2 Each Rupees Five Hundred TwentyFour Paise Fourty Only

2 Core 6 sqmm ARMOURED Cable 20 Each Rupees One Thousand Nine Hundred FourtyFour Paise SixtyFive Only

4.12 Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below:

By TATA-Medium GI pipe 10 Each Rupees One Thousand Six Hundred NinetyEight Paise FiftyFive Only

4.13 Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required

Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36 cm x 86.36 cm x 46 cm deep (below Ground level) complete with cemented brick work(1:6) of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 35.56 cm with locking arrangement, GI reducer including drilling of 46 nos. 12 mm dia holes on the GI pipe 2 Each Rupees Three Hundred SixtyThree Paise Fourty Only

Supplying and fixing 240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection (Legrand / Havells / Siemens/L&T) .

Connecting the equipments to earth busbar including S & F GI (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages 88 Each Rupees Two Hundred Eighteen Paise Fifty Only

Solid GI wire 10 Each Rupees Four Hundred One Paise ThirtyFive Only

No. 8 SWG 2 Each Rupees Three Hundred Seventy Paise Thirty Only

Fixing only single/twin fluorescent light fitting suspended 25 cm bellow the ceiling with 2 No. 20 mm dia EI conduit (14 SWG) supports fixed with “L” type MS clamp whose one side fixed on ceiling with sutable size 4 nos. fastener and other side connected with the conduit with suitable size of bolts and nuts incl. S&F EI conduit, “L” type (125mmx125mm) 6mm thick and 25mm with MS clamps and connecting the length of PVC insulated wire and mending good damages to original finish and painting etc. by 2x24/0.20 mm (1.5sqmm.) flexible copper wire of 1.10 mt. length. 12 Each Rupees One Thousand SeventyEight Paise Seventy Only

Fixing only single /twin fluorescent light fitting complete with all accessories directly on wall/ceiling/HW round block and suitable size of MS fastener 30 Supplying TMC 501 Conventional industrial battens Philips LED tube, model no TMC 501 P 1xT-LED 22W P3241 with 1 no LED Tube 1200mm 18W865 T8 (-210m including necessary connection. 324 Rupees Three Hundred TwentyFour Only

4.16 Supplying of different types of LED lamps (9W) Make Phillips, 9.0 Watt, Base B22/E27,825 Lm

a Supplying and fixing of Endura LED Bulkhead Pressure Die Cast housing Led Bulkhead with IP66 Protection and Ix09 impact resistance suitable for surface and wall mounting applications on ceiling fitting on wall/ ceiling by screws etc. Make: Havells, 10WLED 1 Each 1476

b Supplying and fixing of Endura LED Bulkhead Pressure Die Cast housing Led Bulkhead with IP66 Protection and Ix09 impact resistance suitable for surface and wall mounting applications on ceiling fitting on wall/ ceiling by screws etc. Make: Havells, 10WLED 1 Each 1476 Rupees One Thousand Four Hundred SeventySix Only

c Supplying and fixinof Green LED Ultima Square (6'x6') including the false ceiling in required dimensions also the wiring and connection of the light by 1.5 sq mm cu wire complete Make: Havells, 18 Watt Square/round 6 Supplying TMC 501 Conventional industrial battens Philips LED tube, model no TMC 501 P 1xT-LED 22W P3241 with 1 no LED Tube 1200mm 18W865 T8 (-210m including necessary connection. 767 Rupees Seven Hundred SixtySeven Only

4.17 Supplying and fixing of smart bright essential street light (70 watt) complete with all accessories to be fixed / projected from the wall of the building or on pole including making holes/ providing clamping arrangement and necy. GI reducer as required S & F 40mm GI pipe(medium) quality 1.5 mts average length having suitable bend S & F necy. length of 1.5 sq mm PVC insulated single core stranded annealed copper wire and making connections as required and mending good damages to walll incl. painting etc. Make: Bajaj,70Watt 1 Each 232 Rupees Two Hundred ThirtyTwo Only

4.18 Supplying and fixing of green line V2 street light (115 Watt) complete with all accessories to be fixed / projected from the wall of the building or on pole including making holes/ providing clamping arrangement and necy. GI reducer as required S & F 40mm GI pipe(medium) quality 1.5 mts average length having suitable bend S & F necy. length of 1.5 sq mm PVC insulated single core stranded annealed copper wire and making connections as required and mending good damages to walll incl. painting etc. Make: Bajaj,120 W LED 1 Each 174 Rupees One Hundred SeventyFour Only

Cost for Electrical Works 3 Each 117 Rupees One Hundred Seventeen Only

4.2 Cost for Sanitary & Plumbing Work 3 each 383 Rupees Three Hundred EightyThree Only

4.21 Cost for Fire Fighting Works 1 Each Rupees Six Thousand Two Hundred FiftySix Only

4.22 Cost for Furnitures 1 Each Rupees Seven Thousand Two Hundred SixtyNine Paise Fifteen Only

COST EXCLUDING IGST & LWC (in Rs.) 70 Each Rupees Four Hundred FourtyFive Paise Five Only

4.24 GST @18% (in Rs.) 10 Each

4.25 LWC @1% (in Rs.) 70 Each Rupees SeventyFive Paise Ninety Only

4.26 CONSTRUCTION OF BAGRAKOTE HIGHER SECONDARY SCHOOL IN KALIMPONG I BLOCK, DISTRICT KALIMPONG UNDER RIDF - XXXI

18 Each Rupees Three Hundred SeventyEight Paise ThirtyFive Only

18 Each Rupees Two Hundred TwentyOne Paise NinetyFive Only

4.26 8 Each Rupees One Hundred Five Paise Eighty Only

3 Each Rupees One Hundred FourtyTwo Paise Sixty Only

4.28 70 Each 2053 Rupees Two Thousand FiftyThree Only

4.29 10 Each 2949 Rupees Two Thousand Nine Hundred FourtyNine Only

4.3 4 Each 1863 Rupees One Thousand Eight Hundred SixtyThree Only

14 Each 2093 Rupees Two Thousand NinetyThree Only

4.32 200 Mtr Rupees One Hundred FourtySix Paise Five Only

4.33 80 Mtr Rupees One Hundred EightySix Paise Thirty Only

4.34 Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables as below :

a 200 Set Rupees SeventyTwo Paise FourtyFive Only

b 80 Set Rupees One Hundred ThirtyTwo Paise TwentyFive Only

4.34 Supplying & fixing medium gauge GI Pipe ( ISI-Medium) Protection with necessary fittings and jointing metarials as required

a 10 Mtr Rupees Two Hundred EightyTwo Paise Ninety Only

a 200 Set Rupees Six Paise Ninety Only

c 48 Set Rupees Ten Paise ThirtyFive Only

200 Mtr 160 Rupees One Hundred Sixty Only

2 Set Rupees One Thousand Seven Hundred FiftyTwo Paise Sixty Only

4.38 2 Item Rupees One Thousand FiftyTwo Paise TwentyFive Only

1 Mtr Rupees One Hundred SeventyNine Paise Fourty Only

a No. 6 SWG 20 Mtr

b 200 Mtr Rupees Fourteen Paise NinetyFive Only

4.41 100 Each 1172 Rupees One Thousand One Hundred SeventyTwo Only

40 Each 162 Rupees One Hundred SixtyTwo Only

60 Each 1319 Rupees One Thousand Three Hundred Nineteen Only

8 Each 1060 Rupees One Thousand Sixty Only

20 Set Rupees One Hundred Fifteen Only

80 Each Rupees Two Hundred TwentyEight Paise EightyFive Only

Fixing only lamp 40 Each Rupees Five Paise SeventyFive Only

18 Each 7841 Rupees Seven Thousand Eight Hundred FourtyOne Only

12 Each 11628 Rupees Eleven Thousand Six Hundred TwentyEight Only

Select, At Par, Excess (+), Less (-) IOCL

Tender Inviting Authority: Executive Engineer, West Bengal State Rural Development Agency, Kalimpong Division, Gorkhaland Territorial Administration

Name of Work : Construction of Bagrakote Higher Secondary School in Kalimpong I Block, District Kalimpong under RIDF XXXI, Gorkhaland Territorial Administration

Contract No : 39 of 2025-26_1

Sl. No. Item Description Item Code / Make Quantity Units Estimated Rate Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency BASIC RATE In Figures To be entered by the Bidder Rs. P Excise Duty VAT Freight Charges ( Unloading & Stacking) Any Other Taxes/Duties/Levies Other Taxes 2 IIIrd Party i.e DGS&D / RITES etc Inspection Charges @0.34%+Service Tax Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category

Cost for Building Construction Work 1 Nos. Excess(+) Full Conversion INR

Cost for Sanitary & Plumbing Work 2 Nos. Excess(+) Full Conversion INR

Cost for Protection Wall, Dismantling, Drain and Land Development Works 3 Nos. Excess(+) Full Conversion INR

Cost for Electrical Works 4 Nos. Excess(+) Full Conversion INR

Cost for Fire Fighting Works 5 Nos. Excess(+) Full Conversion INR

Cost for Furnitures 6 Nos. Excess(+) Full Conversion INR

Add @ 18% GST on Cost of Construction 9 Nos. Excess(+) Full Conversion INR

Add @ 1% Labour Welfare CESS on Cost of Construction including GST 10 Nos. Excess(+) Full Conversion INR

Total in Figures

Quoted Rate in Figures Select

Please Enable Macros to View BoQ information