C o SPS type additional class rooms under Priority II SH Providing furniture in various govt schools for additional classrooms under Education PWD Delhi Package A

Amount

Dual Desk :- W 1066mm x D 830mm x H 760/452mm Providing supplying and placing Dual Desk. The overall dimensions of desk will be W 1066mm x D 830mm x H 760/452mm complete as per drawing and direction of Engineer-in- charge having the following specifications:- Side frame structure: Made of prime quality CRCA pressed form section 165mm x25mm x 1mm thick welded to 25mm x 50mm x 1.2mm thick CRCA tube 830mm length. Seat and back side frame structure also made of prime quality CRCA pressed form section 165mm x 25mm x 1mm thick welded to 25.4mm diameter x1.6mm thick ERW -1 pipe. All 8 nos. horizontal supports are 25mm x 25mm x 1.2mm thick shall be CRCA tube. Rectangular tube 50 x 25 x 1.2mm thick should be closed with CRCA welded Sheet both sides and The back pipe dia. 25.4 x 1.6mm thick should be closed with metal process with end sealing machine (Back side) and other side (Under the seat) PPCP cap complete as per drawing. Front panel cum tray shall be made of prime quality 0.8mm thick CRCA sheet of H 150mm x W 1012mm x D 250mm to 300mm with middle partition and side stiffeners of MS CRCA tube size 19mmx19mmx1mm thick. One vertical support (partition) of square tube size 25mm square x 1.2mm thick must be provided at centre of tray and Front Face must be embossed as per drawing. Additional front panel prime quality 0.8mm thick CRCA sheet of size H 150mm x W 1012mm X D 21mm with square perforation. CRCA Tube of size 19 x 19 x 1 mm thick to be inserted for full length at bottom of Jali as shown in Drg. Desktop, seat and back shall be made of IS: 303, 18mm thick plywood of MR grade having AA types of surfaces of OSL (one side 0.6mm thick lamination and one side balancing) and three edges must be sealed with 2mm thick PVC edge banding tape with hot melt glue standard ‘D4499 Jowatherm -280’ on through feed edge banding machine. Edge band must be trimmed on edges and corner, Sizes are below:- 1. Seat W 1066mm X D 300mm. 2. Desktop W 1008mm x D 340mm 3. Back 1066mm x D150 mm 4. One long edge of Desk top, seat & back shall be post formed with round edge. Desktop must be fitted with M6 sunken bolt 3 nos. size M6 x35mm length Zinc plated from Top side, maximum distance 40mm from desktop edge and 3 nos. MS Zinc plated screw self-tapping size dia. 4mm x 38 length again from Bottom side Seat and back each must be fitted with 6 nos. MS screw Zinc plated self-tapping size dia. 4mm x 38 length from Bottom side Hooks made of MS wire dia. 5mm and size W 23mm, D 32mm and H80mm must be provided on inner side of vertical pressed formed steel section on both sides i) All Pipes shall be of ERW-1, IS: 3074-2005/ IS: 4923 and CRCA sheet, IS -513 CR-2 Designation- Grade D). (ii)All MS. CRCA parts must be MIG, TIG or spot welded as per technical requirement All steel components must be powder coated process should be conveyoredcontinues flow to oven and temperature control in oven with thermostatic system. The thickness of desk should be minimum 50 microns dry film thickness(DFT) after 8 tank pre-treatment process flow using Hankel make chemical i.e. Degreasing (1st tank),Water rinsing (2nd tank), Derusting (3rd tank),Water rising(4th Tank), Activation (5th Tank) ,Phosphating (6th Tank),Water Rinsing (7th Tank),Passivation (8th Tank)and dipping should be PLC control line through mechanical transporter The parameter temperature should be displayed at every tank. Passivation (8th Tank) School name must be painted on back side of the back rest and text height will be 25mm PPCP virgin material Shoes of approved quality must be providing in the bottom of frame - 4 nos.

Dual Desk :- W 1066mm x D 830mm x H 705/400mm Providing supplying and placing Dual Desk. The overall dimensions of desk will be W 1066mm x D 830mm x H 705/400mm complete as per drawing and direction of Engineer-in- charge having the following specifications:- Side frame structure: Made of prime quality CRCA pressed form section 165mm x25mm x 1mm thick welded to 25mm x 50mm x 1.2mm thick CRCA tube 830mm length. Seat and back side frame structure also made of prime quality CRCA pressed form section 165mm x 25mm x 1mm thick welded to 25.4mm diameter x1.6mm thick ERW -1 pipe. All 8 nos. horizontal supports are 25mm x 25mm x 1.2mm thick shall be CRCA tube. Rectangular tube 50 x 25 x 1.2mm thick should be closed with CRCA welded Sheet both sides and The back pipe dia. 25.4 x 1.6mm thick should be closed with metal process with end sealing machine (Back side) and other side (Under the seat) PPCP cap complete as per drawing. Front panel cum tray shall be made of prime quality 0.8mm thick CRCA sheet of H 150mm x W 1012mm x D 250mm to 300mm with middle partition and side stiffeners of MS CRCA tube size 19mmx19mmx1mm thick. One vertical support (partition) of square tube size 25mm square x 1.2mm thick must be provided at centre of tray and Front Face must be embossed as per drawing. Additional front panel prime quality 0.8mm thick CRCA sheet of size H 150mm x W 1012mm X D 21mm with square perforation. CRCA Tube of size 19 x 19 x 1 mm thick to be inserted for full length at bottom of Jali as shown in Drg. Desktop, seat and back shall be made of IS: 303, 18mm thick plywood of MR grade having AA types of surfaces of OSL (one side 0.6mm thick lamination and one side balancing) and three edges must be sealed with 2mm thick PVC edge banding tape with hot melt glue standard ‘D4499 Jowatherm -280’ on through feed edge banding machine. Edge band must be trimmed on edges and corner, Sizes are below:- 1. Seat W 1066mm X D 300mm. 2. Desktop W 1008mm x D 340mm 3. Back 1066mm x D150 mm 4. One long edge of Desk top, seat & back shall be post formed with round edge. Desktop must be fitted with M6 sunken bolt 3 nos. size M6 x35mm length Zinc plated from Top side, maximum distance 40mm from desktop edge and 3 nos. MS Zinc plated screw self-tapping size dia. 4mm x 38 length again from Bottom side. Seat and back each must be fitted with 6 nos. MS screw Zinc plated self-tapping size dia. 4mm x 38 length from Bottom side. Hooks made of MS wire dia. 5mm and size W 23mm, D 32mm and H80mm must be provided on inner side of vertical pressed formed steel section on both sides i) All Pipes shall be of ERW-1, IS: 3074-2005/ IS: 4923 and CRCA sheet, IS -513 CR-2 Designation- Grade D). (ii) All MS. CRCA parts must be MIG, TIG or spot welded as per technical requirement All steel components must be powder coated process should be conveyored continues flow to oven and temperature control in oven with thermostatic system. The thickness of desk should be minimum 50 microns dry film thickness(DFT) after 8 tank pre-treatment process flow using Hankel make chemical i.e. Degreasing (1st tank),Water rinsing (2nd tank), Derusting (3rd tank),Water rising(4th Tank), Activation (5th Tank) ,Phosphating (6th Tank),Water Rinsing (7th Tank),Passivation (8th Tank)and dipping should be PLC control line through mechanical transporter The parameter temperature should be displayed at every tank. School name must be painted on back side of the back rest and text hieght will be 25mm PPCP virgin material Shoes of approved quality must be providing in the bottom of frame - 4 nos.

Dual Desk :- W 900mm x D 830mm x H 615/350mm Providing supplying and placing Dual Desk. The overall dimensions of desk will be W 900mm x D 830mm x H 615/350mm complete as per drawing and direction of Engineer-in- charge having the following specifications:- Side frame structure: Made of prime quality CRCA pressed form section 165mm x25mm x 1mm thick welded to 25mm x 50mm x 1.2mm thick CRCA tube 830 mm length. Seat and back side frame structure also made of prime quality CRCA pressed form section 165mm x 25mm x 1mm thick welded to 25.4mm diameter x1.6mm thick ERW -1 pipe. All 8 nos. horizontal supports are 25mm x 25mm x 1.2mm thick shall be CRCA tube. Rectangular tube 50 x 25 x 1.2mm thick should be closed with CRCA welded Sheet both sides and The back pipe dia. 25.4 x 1.6mm thick should be closed with metal process with end sealing machine (Back side) and other side (Under the seat) PPCP cap complete as per drawing. Front panel cum tray shall be made of prime quality 0.8mm thick CRCA sheet of H 150mm x W 1012mm x D 250mm to 300mm with middle partition and side stiffeners of MS CRCA tube size 19mmx19mmx1mm thick. One vertical support (partition) of square tube size 25mm square x 1.2mm thick must be provided at centre of tray and Front Face must be embossed as per drawing. Additional front panel prime quality 0.8mm thick CRCA sheet of size H 150mm x W 846 mm X D 21mm with square perforation. CRCA Tube of size 19 x 19 x 1 mm thick to be inserted for full length at bottom of Jali as shown in Drg. Desktop, seat and back shall be made of IS: 303, 18mm thick plywood of MR grade having AA types of surfaces of OSL (one side 0.6mm thick lamination and one side balancing) and three edges must be sealed with 2mm thick PVC edge banding tape with hot melt glue standard ‘D4499 Jowatherm -280’ on through feed edge banding machine. Edge band must be trimmed on edges and corner, Sizes are below:- 1. Seat W 900mm X D 260mm. 2. Desktop W 846mm x D 338mm 3. Back W 900mm x D150 mm 4. One long edge of Desk top, seat & back shall be post formed with round edge. Desktop must be fitted with M6 sunken bolt 3 nos. size M6 x35mm length Zinc plated from Top side, maximum distance 40mm from desktop edge and 3 nos. MS Zinc plated screw self-tapping size dia. 4mm x 38mm length again from Bottom side Seat and back each must be fitted with 6 nos. MS screw Zinc plated self-tapping size dia. 4mm x 38 length from Bottom side. Hooks made of MS wire dia. 5mm and size W 23mm, D 32mm and H80mm must be provided on inner side of vertical pressed formed steel section on both sides. (i) All Pipes shall be of ERW-1, IS: 3074-2005/ IS: 4923 and CRCA sheet, IS -513 CR-2 Designation- Grade D). (ii)All MS. CRCA parts must be MIG, TIG or spot welded as per technical requirement All steel components must be powder coated process should be conveyoredcontinues flow to oven and temperature control in oven with thermostatic system. The thickness of desk should be minimum 50 microns dry film thickness(DFT) after 8 tank pre-treatment process flow using Hankel make chemical i.e. Degreasing (1st tank),Water rinsing (2nd tank), Derusting (3rd tank),Water rising(4th Tank), Activation (5th Tank) ,Phosphating (6th Tank),Water Rinsing (7th Tank),Passivation (8th Tank)and dipping should be PLC control line through mechanical transporter The parameter temperature should be displayed at every tank. School name must be painted on back side of the back rest and text hieght will be 25mm PPCP virgin material Shoes of approved quality must be providing in the bottom of frame - 4 nos.

Table with Side Unit Providing, supplying and Placing Principal Table with Main table of overall Size 1800mm(L) x 900mm(D) x 750mm(H), Joining table of size 1050w x 1200 D x 750H Side Table of size 1200mm(L) x 600mm(D) x 730mm(H) and Drawer Unit of size 400mm(W) 560mm(D) 560mm(H). The Main Material of the table is MDF Board .Surface : CPL (Continuous Pressure Laminate) in 0.6 mm thickness. Post forming should be done to make approved profile of required colour. Edging : 2 mm PVC Edging, matching colour with hot melt glue at 200°C Main Desk Table Top + Joining Top 25 mm MDF, plus 30 mm MDF (Medium Density Fiberboard) black pad. Modesty Panel: 18 mm MDF. Leg : 25 mm MDF, plus 30 mm MDF right and left pad i/c vertical post as per manufacturers specification Side Table : Table Top Exterior grade shall be made of 25mm thick MDF. Metal Black Spacers of Diameter 4cm, Length 10.4cm. Pedestal Leg : 25 mm MDF Drawer Unit : Top Panel : 25mm MDF. All Other Panels : 18 mm MDF. Lock : Provided. Castor: Provided. Handle: Metal. All the above items should be as per photo, sketch, specifications & direction of Engineer-in-charge.

Office Tables Providing, supplying and placing office table of size 1500mm(L) x 750mm(D) x 725mm(H). Work surface of the table shall be made from 18mm thick Pre Laminated wooden Ply (Lami Ply, MR grade as per IS:303) with decorative lamination(0.8mm thick) on both sides for top (Table). All work surface edges are duly sealed with 2mm thick PVC edging of matching colour with hot melt glue at 200°C . Understructure of the table comprises Modesty Panel made from 18mm thick Pre Laminated wooden Ply (Lami Ply, MR grade as per IS 303). All work surface edges are duly sealed with 2mm thick PVC Edge banding and rectangular Frames Fabricated from 1.2mm thick Cold Rolled Close Annealed (IS:513), Finish of metal parts - Powder coat (Epoxy polyester). Leg should be Fabricated component from 38mm x 25mm x 1.2mm thick MS ERW Tube (IS:4923) with Powder coat (Epoxy polyester). CPU Modesty made from 0.8mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester), Plastic Cap for Cable travel should be Injection Moulded Polypropylene. Leveler glide for Leg of Nylon 6 & MS Bolt. Drawer Unit with 3 Drawers shall be provided of size 670mm(H) X 559mm(D) X 355.5 mm(W), Shell, drawer tray, Drawer Front, Frame Assembly of the drawer unit shall be made of 0.8mm thick CRCA (IS:513) with Powder coat (Epoxy polyester). 10 lever cam Lock shall be provided for locking. Handle shall be made from Injection Moulded Polypropylene & Leveler of Nylon6 & MS Bolt.( All the corners should be rounded not shown in picture.)All the above items should be as per photo, sketch specifications & direction of engineer-in-charge.

library tables/Student Work Table Providing, supplying and placing library table of overall size 1800mm(L) x 900mm(D) x 740mm(H).The worktop of the table shall be made from 25 mm thick MDF Board ( Exterior grade) with 2mm thick PVC edging matching colour with hot melt glue at 200°C open edges of work top. Understructure of the table comprises C-Frames of 1.6 mm thick M.S CRCA with Powder coating upto 40-50microns. C-frame 75mm for supporting the Top & 75mm long recess for 4 No legs of Diameter 38.1mm x 1.6 mm thick M.S ERW tube with powder coated shall be provided. The detachable legs shall be duly screwed with C- frame and recessed . (All the corners should be rounded not shown in picture.) All the above items should be as per photo, sketch, and specifications & direction of engineer-in-charge.

Teachers Table/Instructor's Table: Providing, supplying and placing office table of size 1200mm(L) x 600mm(D) x 725mm(H). Worksurface of the table shall be made from 18mm thick Pre Laminated wooden Ply (Lami Ply, MR grade as per IS:303) with decorative lamination(0.8mm thick) on both sides for top. All work surface edges are duly sealed with 2mm thick PVC edging of matching colour with hot melt glue at 200°C. Understructure of the table comprises Rectangular Frames Fabricated from 1.2mm thick Cold Rolled Close Annealed (IS:513), Finish of metal parts - Powder coat (Epoxy polyester). Leg should be Fabricated component from 38mm x 25mm x 1.2mm thick MS ERW Tube (IS:7138) with Powder coat (Epoxy polyester). Modesty panel shall be 0.8mm Thick CRCA Sheet duly poweder coated. One Side Panel made from 0.8mm thick CRCA (IS:513). Wire Carrier shall be provided, Vertical Wire Carrier along with Drawer made of 0.8mm Thick CRCA Grade D as per IS:513 and Horizontal Wire carrier under the worktop made of 0.8mm thick CRCA Grade D as per IS:513 complete powder coated. Finish: Powder coat (Epoxy polyester), Plastic Cap for Cable travel should be Injection Moulded Polypropylene. Leveler glide for Leg of Nylon 6 & MS Bolt. Drawer Unit with 3 Drawers shall be provided of size 670mm(H) X 550mm(D) X 350mm(W), Shell, drawer tray, Drawer Front, Frame Assembly of the drawer unit shall be made of 0.8mm thick CRCA (IS:513) with Powder coat (Epoxy polyester). 10 lever cam Lock shall be provided for locking. Handle shall be made from Injection Moulded Polypropylene & Leveler of Nylon6 & MS Bolt. All the above items should be as per photo, sketch specifications & direction of engineer-in-charge.

Computer Tables Providing, supplying and placing Computer table of overall dimension 900mm(W) x 550mm(D) x 740mm(H). The base material for computer table should be MDF board 18 mm thick lami ply with decorative lamination on both side as per IS: specification exterior grade conforming to IS:14587 with 2mm lipping. It should provides higher resistance to heat and moisture. The understructure of the Table should be Fabricated component from 38mm x 25mm x 1.2mm thick MS ERW Tube (IS:4923) with Powder coat to the thickness of 40-50microns . The Table should be provided with a with metal Keyboard Tray. Single Drawer is provided on the right side of the table of size 150mm(L) x 300mm(D) x 100mm(H) with MDF facia and sliding channels. A Shelf is provided of size 600mm(L) x 200mm(D) for keeping files. A CPU stand is in built in the understructure of size 200mm(W) x 500mm(D).All the above items should be as per photo, sketch, specifications & direction of engineer-in-charge.

Table 3Ftx2Ft. Providing ,Supplying & placing Table of an overall size 900mm(L)x600mm(W)x750mm(H) with top made up of 25mm thick MDF board with decorative laminate on top and balancing laminate on unexposed face. The understructure (gable and modesty) is made of 18mm thick Pre Laminated wooden Ply (Lami Ply, MR grade as per IS:303) with decorative lamination(0.8mm thick) on both sides and all exposed edges sealed with matching colour 2mm thick PVC edging with hot melt glue at 200°C . Table has a provision for wire manager caps at top. All the corners should be rounded not shown in picture. The table should be as per photo, sketch, specifications & direction of engineer-in-charge.

Floor Level Table Providing Supplying and placing of Floor Level Table of an overall size 1500mm(L)x600mm(W)x300mm(H) with top made up of 25mm thick MDF board ( Exterior grade) with decorative laminate on top and balancing laminate on unexposed face. The understructure (gable end and modesty ) is made of 18mm thick Pre Laminated wooden Ply (Lami Ply, MR grade as per IS:303) with decorative lamination(0.8mm thick) on both sides and all exposed edges sealed with matching colour 2mm thick PVC edging with hot melt glue at 200°C banding tape and all unexposed edges sealed with PVC edge banding tape pressed at 200° C with hot melt glue on special machines. Table has a provision for wire manager caps at top. All the corners should be rounded not shown in picture. The table should be as per photo, sketch, specifications & direction of engineer-in-charge.

Principle Chair Providing,supplying and Placing in position High Back Chair. The seat shall be made of 1.4 +/-0.1 cm thick hot pressed plywood upholsterd with fabric and moulded polyurethane foam. It shall have seat depth adjustment of 5.0 +/- 0.3cm integrated in the seat through a sliding mechnism. Seat size shall be 50.0cm(W) x 49.0cm(D). The back shall be injection moulded in glass filled polyamide which shall be upholstered with mesh fabric. The back shall consist adjustable lumbar support made of injection moulded polypropylene having an adjustment of 6.0 +/- 0.1 cm. Back size shall be 50.0 cm W x 68 .0 cm H. The polyurethane foam for seat shall have a density of 55 +/- 5 kg/m³. The height adjustable armrest shall be made of polyamide structure and polypropylene housing with moulded PU armtop having an adjustment of 7.0 +/- 0.3 cm. The mechanism shall be dsigned with following features -: 360º revolving type, Centre Tilt Syncro Mechanism, 3 position (inclusing upright lock) giving option of variable tilt angle to the chair with anti shock feature. The headrest shall be injection moulded in glass filled polypropylene which shall be upholstered with foam and fabric. It shall have an adjustment of 6.0 +/- 0.1 cm and it shall be assembled over the full back chair. The Headrest shall be provided with a provision of Coat Hanger. The pneumatic height adjustment shall have an adjustment stroke of 8.5 +/- 0.3 cm. The pedestal shall be High presssure Die cast aluminium and fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0 +/- 0.5 pitch centre dia. The twin wheel castors shall be injection moulded in black glass filled polyamide having 6.0 +/- 0.1 wheel dia. All the above item should be as per photo, sketch and specifications & direction of engineer-in-charge.

Principle Visitor's Chair Providing,supplying and placing in position Principal Visitor Chairs. Chair Seat and Back assembly shall be made up of 1.2+/- .2 cm thick hot pressed plywood, upholstered with fabric and moulded Polyurethane foam together with moulded seat and back covers. The Seat is provided with a pre-moulded inserts at the bottom for fixing Mechnism and Armrests. The back foam is designed with contoured lumbar support for extra comfort. Back size: 50.0cm(W) x 49.0cm(H) Seat size: 50.0cm.(W) x 46.0cm(D) The polyurethane foam shall be moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 at 25% compression. Seat and Back shall be provided made of injection moulded in black co-polymer polypropylene and back cover is vacuum formed from ABS sheets. ARMRESTS : The one piece armrests made of black integral skin polyurethane with 50-70 Shore 'A' hardness and reinforced with M.S. Insert. The armrests are scratch and weather resistant. The armrests are fitted to the seat with seat/armrest connecting strip assembly ,made of 0.5cm thick HR steel. The understructure is tubular frame in cantiliver type and made up of dia 2.54cmx0.2cm thick MS ERW tube and black powder coated. (DFT 40-60 microns). All complete as per manufacturers specification, approved sample and direction of Engineer-in-Charge.

Teacher chair/Chairs Providing, supplying and placing of Visitor Chairs. The Seat and Back Assembly shall be made up of 1.2cm thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. The Seat is provided with a pre-moulded inserts at the bottom for fixing Armrests. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE : 47.5cm(W) x 58.0cm(H) and SEAT SIZE : 47.0cm(W) x 48.0cm(D). The Polyurethane foam is moulded with density = 45 +/-2 kg/m 3 and Hardness = 20 +/- 2 at 25% compression. ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. TUBULAR FRAME : The powder coated tubular frame is cantilever type & made of dia 25.4mm x 2mm thick M.S. ER.W. Tube as per sketch for item. All the above items should be as per photo, sketch ,specifications& direction of Engineer-in-Charge.

Computer Chair Providing, supplying and placing of Revolving Computer Chair. The seat and back are made up of 1.2 cm thick hot pressed plywood, upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The Seat is provided with a pre-moulded inserts at the bottom for fixing Mechnism and Armrests. The back foam is designed with contoured lumbar support for extra comfort. BACK) SIZE: 40.0cm. (W) X 47.0cm. (H) SEAT SIZE: 45.0cm. (W) X 42.0cm. (D). The HR Polyurethane foam is moulded with density=45+/-2 kg/m cube and hardness load 16+/-2 kgf as per IS:7888 for 25% compression. The one piece armrests are injection moulded from black nylon. The armrests are fitted to the seat with armrest connecting brackets made of 0.5cm. thk. HR steel. The permanent contact mechanism is designed with 360° revolving type. 14° maximum back-tilt only.Upright position locking. Tilt tension adjustment. The pneumatic height adjustment has an adjustment stroke of 11.0 cm.The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 62.0cm. pitch-center dia. (72.0 cm with castors).The twin wheel castors are injection moulded in Black Nylon. All the above items should be as per photo, sketch , specifications & direction of engineer-in-charge.

Support Staff Room & Guard Room chair Providing, supplying and placing of Visitor Chair. Seat/Back Assembly : The seat and back are made up of 1.2+/- .2 cm thick hot pressed plywood, upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam is designed with contoured lumbar support for extra comfort. back size: 49.0cm.(W) x 47.0cm.(H) Seat Size: 49.0cm(W) x 44.0cm(D) POLYURETHANE FOAM: The polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 on Hampden machine at 25% compression. TUBULAR FRAME : The tubular frame is cantilever type & made of Dia 2.54cm(1”) x 14 BG M.S. E.R.W. tubeand black powder coated. All the above items should be as per photo, sketch and specifications & direction of engineer-in-charge.

Art room Students Stool Providing, supplying and placing Students Stool (of seat 400mm dia) having compacted and moulded ply in seat 15mm +/- 1mm thick with cross support of 19 +/- 1mm dia square pipe 1.5 mm thick below base. The frame material and back support of 5 pipes is made up of 25mm dia round pipe and 1.5 mm thick SS202 with chrome finish. Noiseless PVC shoe below the frame as per photo, sketch , specifications & direction of engineer-in-charge.

Lab Stools Providing and placing of fixed type Stool with SS Round Top. Overall size is 480mm(L) x 480mm(W) x 560mm(H). Understructure of the stool consists of 4 Legs, circular Foot Step welded at 150mm above from ground and Top Frame. Complete understructure shall be made up of MS ERW Tube of 22mm Dia having a thickness of 1.6mm with duly powder coated 40-45microns. A Round Top of size 300+/-5mm Dia shall be fixed on the top frame made of 1mm Thick Stainless Steel (SS) with buffed Glossy finish. PVC Shoes shall be provided at the bottom of all legs to avoide direct contact of metal parts with floor. Stool shall be safe upto 120Kgs Load. All the above items should be as as per photo, sketch and specifications as per the direction of engineer-in-charge.

Library Chairs Providing, supplying and placing of Library Chairs for Students. The seat and back of the chair shall be made up of 1.2cm thick hot pressed plywood, upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam is designed with contoured lumbar support for extra comfort. BACK) SIZE: 40.0cm. (W) X 45.0cm. (H) SEAT SIZE: 43.0cm. (W) X 39.0cm. (D). The High Resillience Polyurethane foam is moulded with density=45+/-2 kg/m cube and hardness load 16+/-2 kgf as per IS:7888 for 25% compression. TUBULAR FRAME : The tubular frame is made up of Dia 2.54cm+/-0.03cm x 0.2+/-0.016cm Thick M.S. E.R.W tube and black powder coated. All the above items should be as per photo, sketch and specifications & direction of engineer-in-charge.

M.P. Hall chair Providing supplying and placing Seminar room chair. The seat and back shall be made of injection moulded polypropylene shell. The seat shall be upholstered with high resiliance polyurethane foam 19mm thick having density 40kg/m³ with Fabric upholstry . The PP shell shall be supplied in perforated position and fixed with main frame. The frame structure shall be supported by four legs made up of MS/CRCA chrome plated tubular pipe frame having cross-section area 25mm X 12mm with 1.6mm thick. There shall be co-polymer polypropylene shoe provided at the base to avoid scratches on the floor. The seat size shall be 400±10 mm(D) X 410±10 mm(w) and back size sall be 455±10 mm(W) X 370±10 mm(H) from seat. Overall height shall be = 820±10 mm & overall depth = 565±10 mm. All the above items should be as per photo, sketch and specifications & direction of engineer-in-charge.

Sofa Set(3 +1+1) Providing, supplying and placing sofa set(3+1+1). 3 Seater sofa having overall size of 1750mm(L) x 870mm(D) x 730mm(H) and 1 Seater Sofa having overall size of 920mm(L) x 870mm(D) x 730mm(H) and Seat Height of 390mm upholstered with Synthetic leather with seasoned solid wood frame material of size 50mm x 50mm, Seat of PU foam with foam density of 28 Kg/cubic cm and Back Foam density of 22 kg/cubic cm and ( 100mm thick) webbing material Nylon of 50 mm thickness including springs hassen cloth, cotton. Hard wood facia 18mm thick solid wood is to be provided on the Arm facia. All the above items should be as per photo, sketch , specifications & direction of engineer-in-charge.

Lockers Providing, supplying and Placing set of 12 Lockers. Overall Size : 1150mm(W) x 450mm(D) x 1830mm(H). Construction : Rigid knockdown construction. Material : CRCA 0.8mm Thickness. Locking : 10 Lever Cam Lock arrangement. Shelf Uniformly Distributed Load Capacity per each shelf level is 35 Kg maximum. Finish : Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10).Handle / Label holder • Aesthetically appealing Snap fit ABS plastic handle. Plastic label holder for identification. Ventilation Attractive punched pattern for ventilation. . All the above items should be as per photo, sketch and specifications & direction of engineer-in-charge.

Classroom Almirah Providing and Placing in position Storage Unit for Classroom of overall size 1000mm(W) x 500mm(D) x 2025mm(H) including levellers. The storage unit shall be divided into 2 parts of 500mm(W) each by a vertical partition of 1980mm(H). The storage units shall be stacked widthwise to form a row of storage having a common side panel. The construction of the storage units shall be aesthetically appealing and knock down or welded. Legs shall be fitted in the floor units with screw type leveller and material shall be from combination of CRCA sheet of 0.8mm thick. The storage units shall be provided with height wise adjustable 4 shelves mounting with slots of pitch 25.4mm from top to bottom at all internal corners in classroom almirah , each shelf shall have a load capacity of 40 kg Uniforming Distributed Load. The storage will have steel 2 Nos Hinged Door with self closing hinges and individual lock for each door. Each door shall be provided with a handle Ergonomically designed with Aesthetically appealing made from Aluminium. The complete floor units shall be provided with 3 way locking and Finished with Epoxy Powder coated to the thickness of 50 microns(+/-10). All the above items should be as as per photo, sketch and specifications as per the direction of engineer-in-charge.

Providing, supplying & placing metal storage with locker.The overall size of the storage shall be 910-916mm (W) x480 -486mm (D) x 1980-1981mm (H). The contruction shall be welded/rivetted construction with 0.8 mm thick CRCA for shelf and 0.8mm thick for back. The door shall be made of 0.8mm thick CRCA sheet with having minimum 3 hinges on each door in almirah and all other metal component shall be made of 0.8mm thick CRCA. Stiffners shall be provided from top to bottom in the almirah to prevent any deflection/deformations on the outer body. A locker shall be provided inside the almirah of size 400mm(W)X300mm(H) with locks & door fixed on hinges .The locking and handle of the storage shall be mazak handle with three way locking mechanism. The Alimrah should have 2 welded Legs along the depth of the Almirah of 75mm Width x 125mm Height made up of 1mm thick galvanized sheet which acts as a understructure of the storage. The shelving shall be height adjustable with slots of pitch 25.4mm from top to bottom at all internal corners and shall have a load capacity of 40kg. The product shall be epoxy powder coated to the thickness of 50 microns. All the above items should be as per photo, sketch and specifications & direction of engineer-in-charge.

Wall Mounted Storages Providing and placing Wall Mounted Storage Units with Metal Body and Wooden Shutters. Storage Cabinets to be of complete modular design Consisting of Cabinet Frame, Wooden shutters, shelves and stainless steel D shape handles. Cabinet frame to be of 0.8mm +/- 0.07mm CRCA MS sheet as per IS-513 with Horizontal Stiffners made from 1.2mm +/- 0.09mm thick CRCA as per IS-513. Wooden Shutters are made from 18mm+/-0.5mm thick interior grade Pre-Laminated Particle Board as per IS-12823. All the edges of the door are duly sealed with 2mm thick PVC Edge Banding. Heightwise 1No CRCA adjustable shelf shall be provided in each storage having a load carrying capacity of 25kg UDL. Hinges to be spring loaded with CED coating with self closing mechanism. The complete M.S. material of cabinet to be pretreated (degreased, Zinc phosphated) and epoxy powder coated for better corrosion resistance. The thickness of powder coat to be 50 +/-10 microns(minimum) as per specification. Each unit should have a locking facility with 10Lever cam lock mechanism. All the above items should be as per photo, sketch specifications & direction of engineer-in-charge. Storage Unit of size 600mm(W) x 325mm(D) x 750mm(H)

Storage Unit of size 750mm(W) x 325mm(D) x 750mm(H)

Filing Cabinets Providing, supplying and placing Office Filing Cabinet with Glass Sliding Doors of overall size 900mm(W) x 450mm(D) x 1830mm(H). Filling Cabinet Construction & Material shall be Rigid Knock down construction made from Prime Quality CRCA Steel of 0.8 mmThick. Sliding Door Arrangement shall be provided for Full height Sliding Door with top hanging arrangement to prevent derailment. Each door shall be provided with 2 Plastic roller having steel ball bearing for smooth movement of door & less noise. Lock shall be Snap on type aesthetically appealing die cast 5 Lever Cam lock for safe locking and Handles shall be Plastic flush & recessed handle. Each Cabinet shall be provided with Height wise Adjustable Shelf Mounting with Uniformly Distributed Load Capacity per each full shelf of40Kg maximum. Cabinet shall have 4 Nos. of Adjustable Shelves. Leveler shall be provided at the bottom of the Cabinet of Screw type leveler with hex plastic base to add in unit height min 0.8mm & additional 5mm max for adjustment. Complete Filling Cabinet shall be Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10) with front glass of 4mm Thick to see through the objects placed. All the above items should be as as per photo, sketch and specifications as per the direction of engineer-in-charge.

Display Rack Single Stack - Main Unit (900X350X2100) Providing, supplying and placing of open display racks for books. The rack is prepared from Rigid Knockdown construction in which material shall be CRCA Sheet of 0.8mm Thickness with Epoxy Polyester Powder coated finish to the thickness of 50 microns (+/-10). Stackability: The add-on units can be stacked width wise to form a bank of racks having common side panel. Accessibility: From Front in single sided and Front & Back in double sided racks. Number of Adjustable shelf: 5Nos adjustable shelves shall be provided in single sided racks on one side i.e. Total 6 Loading levels. and 10Nos adjustable shelves shall be provided in double sided racks on one side i.e. Total 12 Loading levels. Uniformly Distributed Load Capacity per each shelf shall be 40 Kg maximum. Shelf back stiffener at the rear side of the shelves back stiffeners are provided. These act as separators between front & rear books. Label holder & range indicator Label Holder & Range indicator on each main unit for inserting labels. All the above items should be as per photo, sketch and specifications & direction of engineer-in-charge

Bookcase Providing and placing in position 4 Door Bookcase of size 910mm(W) x 320mm(D) x 1740mm(H). It has Rigid Knock down construction and Prime Quality CRCA Steel -Top, Back & Side Panels shall be made from 0.8mm high yield strength CRCA & rest in 0.8mm CRCA. Each Door has 6 Lever Cam lock with common key. Each Door has 3mm thick transparent glass for clear inside vision secured in a Metal Frame through rubber gasket. Each door shall have a Scissor mechanism for receding inside the top of respective compartment & ensures parallel & smooth movement. Each door shall have plastic side end caps as Handle which shall be for easy to grip, each compartment shall have a storage shelf with Uniformly Distributed Load Capacity per each shelf shall be 40 Kg maximum. The finish shall be Epoxy Polyester Powder coated to the thickness of 50microns (+/-5 micron). All the above items should be as as per photo, sketch and specifications as per the direction of engineer-in-charge

Rack Storage (Closed Type) Providing, supplying and placing of Slotted Angle Racks with back and two sides closed of Overall Size 1800mm(H) x 900-910mm(W) x 375mm(D). Each rack shall be provided with 5 panels for loading having 40kgs Load carrying capacity (Uniformly Distributed Load) per panel. Close Type Rack system consists of 0.8mm Thick Cold Rolled Close Annealed sheet on 3 sides to make it close type. It also consistes Angle, Decking Panel, Corner plate, Nuts & Bolts. Angles : Material of Angles is as per IS 10748. The thickness of the angles when made from sheet steel shall be 2 mm. Angles shall be of rolled formed construction and free from twist, sharp edges and burrs. Angles shall have holes provided at a pitch of 19.05mm. The holes shall start at 19 mm centers from each end. Size of the Angles should be 40mm x 40mm x 2mm(Thick). Panels : Material of panels is as per IS 10748 / IS5986- Fe 410. Panels shall be 6 bend panels and shall be made from mild steel sheets not less than 0.8 mm in thickness with lipped flanges. Width of flange and lip being 31mm & 17 mm. The panels shall have 9mm holes for corner plates.. Panels will have 6 bends &get bolted to the Angles at each of the four corners according to Minimum of 100 Kg load per level. Corner Plates (Gussets): Material of corner plates is as per IS 513D. 8Nos Corner Plates, four on each face shall be fitted to the open type rack. They shall be made of mild steel sheet and be provided with a black powder coated finish. Corner Plates of 2 mm thickness to be provided for ensuring rigidity of the structure. Nuts &Bolts : All fasteners like nuts, bolts, clips etc shall be supplied in galvanised condition for protection against environment and corrision. All the above items should be as per photo, sketch and specifications & direction of engineer-in-charge.

Newspaper Stand/Display Stand cum Storage Unit Providing, supplying and placing in position News Paper / Magazine Stand of overall size 900mm(W) x 450mm(D) x 1830mm(H). Construction of the unit shall be Rigid Knock down construction. Panels of the unit shall be 0.8mm Thick. Front frame shall be 0.8mm Thick CRCA Steel duly powder coated 50microns(+/-10). Each unit shall have 5 Retractable display Metal Trays fixed at an angle for easy viewing. Tray shall be Receding type to access the storage behind the tray. Retractable feature of each Tray is achieved through Sliding on plastic rollers. Uniformly Distributed Load Capacity per each shelf is 40Kg maximum. The unit shall be provided with Screw type leveler with hex plastic base of height 8mm with an adjustable height of 5mm max for. The complete unit shall be Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10). All the above items should be as as per photo, sketch and specifications as per the direction of engineer-in-charge.

Small Rack Providing, supplying and placing of Slotted Angle Racks of Overall Size 900mm(H) x 900-910mm(W) x 375mm(D). Each rack shall be provided with 3 panels for loading having 40kgs Load carrying capacity (Uniformly Distributed Load) per panel. Open type Rack system consists of Angle, Decking Panel, Corner plate, Nuts & Bolts. Angles : Material of Angles is as per IS 10748. The thickness of the angles when made from sheet steel shall be 2 mm. Angles shall be of rolled formed construction and free from twist, sharp edges and burrs. Angles shall have holes provided at a pitch of 19.05mm. The holes shall start at 19 mm centers from each end. Size of the Angles should be 40mm x 40mm x 2mm(Thick). Panels : Material of panels is as per IS 10748 / IS5986- Fe 410. Panels shall be 6 bend panels and shall be made from mild steel sheets not less than 0.8 mm in thickness with lipped flanges. Width of flange being 31mm and 17mm respectively. The panels shall have 9mm holes for corner plates. Panels will have 6 bends &get bolted to the Angles at each of the four corners according to Minimum of 100 Kg load per level. Corner Plates (Gussets): Material of corner plates is as per IS 513D. 8 Nos Corner Plates, four on each face shall be fitted to the open type rack. They shall be made of mild steel sheet and be provided with a powder coated finish. Corner Plates of 2.00 mm thickness to be provided for ensuring rigidity of the structure. Nuts &Bolts : All fasteners like nuts, bolts, clips etc shall be supplied in galvanised condition for protection against environment and corrision. All the above items should be as as per photo, sketch and specifications as per the direction of engineer-in-charge

Metal Frame Hard Bed Providing,supplying and placing in position Sheet Metal Bed with Mattress of Overall outer dimension should be 2100mm(L) x 900mm(W) x (H) 600mm(Lying Surfavce Height) Head board & foot board Head board of size 900mm(W) x 1050mm(H) and Foot board of size 900mm(W) x 800mm(H) having curved profile at the top made of MS ERW round tubes of thickness 1.6mm & dia 31.75 mm..Head board and leg board is further strengthned by 3 vertical pipes each of thickness 1.2 mm and dia of 19mm & 1 each Horizontal pipe of thickness 1.2mm and dia of 25.4mm Lying surface Lying surface should be made of 1 mm thick CRCA sheet including welding with full length of C frame 50 mm for Metal Channel . This bend panel is further strengthned on the longetudienly edges by welding full length with the help of C shaped metal channel section. Middle of 8 bend panel is strengthned by 5 L shapped stiffners. It should be strengthned by trapizodal contour ( rounded corner ) 10 nos, embossed cut out. All metal components should be pre treated with zinc phosphating and then powder coated with anti microbial epoxy polyster powder coating. Leg shoe Neoprene rubber with reinforced metal washer should be used for leg shoes. Head board and leg board are connected to mattress platform thru L bracket at 4 corners to ensure rigidity, with the help of zinc plated screws Powder coating All metal components should be pre treated with zinc phosphating in 9 tank porcess and then powder coated with anti microbial epoxy polyster powder coating. Maximum weight Maximum safe working load must be 135 kg. Mattress Mattress- overall dimension 2100mm(L) x 900mm(W) x 100mm(H). The bed should be provided with 40 density 100 mm thick foam mattress with water proof, x-ray permeable, fire retardant and vapour permeable cover.All the above items should be as per photo, sketch specifications & direction of engineer-in-charge.

Modular Workstations Providing,supplying and placing in position Modular Workstations with Fabric Screen as per site requirement. The understructure of the workstation comprises of Powder Coated Leg Assemblies, Cross connectors. On the matrix of Legs and Cross connectors, the Work-surfaces are fixed. Table Legs are fabricated by rectangular holo tubes by CO2 welding MS ERW Tube 50mm x 50mm x 1.2mm thick (as per IS: 7138 ERW). The base of the MS tube is fitted with a Glide plate over which an M8 Leveler is fitted, which allows for adjustment of the height by 10mm and coated with minimum 45 micron thickness of epoxy powder coating. Worksurface made of interior grade of approved shade made from 25mm thick Pre-Laminated Board conforming to IS: 12823-Class E1 (As per EN 13986). All the edges of work surface shall be provided with machine pressed 2mm thick PVC lipping glued with hot melt EVA glue. The worktop shall be provided with a 50mm Dia Grommet cut-out for wire management and a horizontal wire carrier fitted below the worktop to carry wires along the length of the workstation. The wire carrier is made with a combination of 3mm and 5mm MS Rod (IS: 9550 Bright Bar) along with 5mm thick MS Plate (IS: 2062, 5mm HR) duly powder coated. The workstation shall be provided with a full length (end to end) Fabric screen of 450mm(H) x 23mm Thick made of Plain Particle board uphostered with Fabric fitted in a aluminum extrusion (HE-9, IS : 63400) frame. The screen assembly is fitted to the Understructure and worktop by brackets made of 3mm thick MS Plate (IS:2062 3mm HR) which are fabricated by welding. The bracket is powder coated matching to the colour scheme of understructure. All the above items should be as per photo, sketch specifications & direction of engineer-in-charge. Workstation of size 1200mm(L) x 600mm(D) x 1200mm(H) with Worktop Height 750mm

Workstation of size 1500mm(L) x 600mm(D) x 1200mm(H) with Worktop Height 750mm

Providing of light motor vehicle/inspection vehicle like Suzuki- Dzire, Honda- Amaze, Hyundai-Accent or equivalent preferably in white colour & having commercial registration number for inspection of works and day to day requirement cost of fuel /lubricant, wages of driver, maintenance and taxes as applicable etc. as per terms & conditions in all working days (except Sunday & Holiday) or whenever required along with driver on hire charge basis upto 10 hours per day and mileage upto 2300 kms in a month.

Methodex Systems Pvt. Ltd.

Spacewood Furnishers Pvt Ltd