Construction and Augmentation work for Pilgrim Facilities at Gangotri Distt. Uttarkashi. (Uttarakhand)

Amount

SUB HEAD -1 EARTH WORK :-

Clearing jungle incuding uprooting of rank vegetation , grass, brush wood , trees and saplings of girth up to 30cm measured at a height of 1m above ground level and removal of rubbish up to a disance of 50m outside the periphery of the area cleared

Earth Work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm in plan) including dressing of sides and ramming of bottoms , lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m.

all kinds of soil

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.Hard rock (requiring blasting)

Earth Work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm inn depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth. Lead up to 50m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.

all kinds of soil

Extra for every additional lift of 1.5 m or part thereof in.

All kind of soil.

Excavation trenches of required width for pipes, cables, etc. includign excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m including getting out the exceeding soil, and then returning the soil as required, in layers not exceeding 20cm indepth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50m.

All kinds of soil

pipes, cable etc. exceedign 80mm dia. But not exceedign 300mm dia.

Filling available excavated earth (excluding hard rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth: consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m.

Supplying and filling in plinth with fine sand under floors including, watering, ramming consolidating and dressing complete.

Carriage of materials including loading, unloading and stacking, upto 5 km.

Carriage of materials including loading, unloading and stacking, beyond 5 km upto 10km Sand, stone aggregate below 40 mm nominal size

Carriage of materials including loading, unloading and stacking, beyond 5 km upto 10km stone aggregate 40 mm nominal size and above

Carriage of materials including loading, unloading and stacking, beyond 5 km upto 10km Bricks

Carriage of materials including loading, unloading and stacking, beyond 5 km upto 10km Cement, stone blocks, G.I.. C.I., A.C., & C.C. pipes below 100 mm dia and other heavy materials

Supplying chemical emulsion in sealed containers including delivery as speciffied

Chlorpyriphos / Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST- CONSTRUCTIONAL anti termite treatment (excluding the cost of chemical emulsion)Along external wall where the apron is not provided using chemical emulsion @ 7.5 ltr / sqm of the vertical including excavation channel along the wall and rodding etc. complete

with chlorpyriphos/ lindane E.C 20% with 1% concentration

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.

With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration.

SUB HEAD -2 CONCRETE WORK :-

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level.

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size).

1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Providing and fixing upto floor five level precast cement concrete string or lacing courses, coping , bed plates , anchor blocks , plain wndow cill , shelves , louvers , steps , staircases etc including hoisting and setting in position with cement mortar 1:3 ( 1 cement : 3 coarse sand ) , cost of required centering , shuttering and finishing smooth with 6 mm thick cement paster 1 : 3 ( 1 cement : 3 fine sand ) on exposed surfaces complete

1 :1.5 : 3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size )

Providing and laying damp proof course 50 mm thick with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size )

Extra for providing and mixing waterproofing material in cement concrete work @ 1kg/50kg of cement.

Providing & Applying a coat of residual petroleum bitumen of pentration 80/100 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

SUB HEAD - 3 R.C.C WORK:-

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.

All works upto plinth level

All works above plinth level upto floor V level

Add or deduct for providing richer or leaner mixes respectively at all floor level

Providing M30 grade concrete by using 420 kg of cement per cum of concrete instead of M25 garde B.M.C. / R.M.C

Centring and shuttering including strutting, propping etc. and removal of form for:-

Foundations, footings, bases of columns, etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform.

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillar, Piers, Abutments, Posts and Struts.

Stairs, (excluding landings) except spiral-staircases.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

Thermo-mechanically treated bars.

Extra for additional height in centring , shuttering where ever required with adequate bracing , propping etc including cost of de shuttering and decentring at all levels , over a height of 3.5 m for every additional height of 1 metre or part thereof ( plan area to be measured )

Suspended floors , roofs , landings, beams and balconies ( plan area to be measured)

SUB HEAD - 4 MASONRY WORK :-

Brick work with F.P.S. bricks of class designation 7.5 in foundation and plinth in:-

Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with F.P.S brick of class designation 7.5 in superstructure above plinth level upto floor V level in all shapes and sizes in cement mortar 1:6 (1 cement : 6 coarse sand).

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

Cement mortor 1:3 (1 cement : 3 coarse sand)

Cement mortor 1:4 (1 cement : 4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every thirdcoarse of half brick masonary (with F.P.S. bricks)

SUB HEAD - 5 WOOD & PVC WORKS :-

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Second class teak wood

Providing and fixing paneled or paneled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding paneling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)

Second class teak wood 35 mm thick shutters

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.

Second class teak wood 35 mm thick shutters

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) Over item no. 9.20 and 9.21.

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured) :

Rectangular or square.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Second class teak wood

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

Providing and fixing aluminium sliding door bolts, ISI marked anodised(anodic coating not less than grade AC 10 as per IS : 1868),transparent or dyed to required colour or shade, with nuts and screwsetc. complete :

Providing and fixing IS : 3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete.

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour orshade with necessary screws etc. complete :

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Single rubber stopper

Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

SUB HEAD - 6 FLOORING WORKS :-

Marble stone flooring with 18mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with :

Agaria White

Udaipur green marble

Extra for prefinished nosing to treads of steps of marble stone.

Extra for marble stone flooring in treads of steps and risers using single length upto 2.00 metre .

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with :

Second class deodar wood

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and laying Ceramic glazed floor tiles 300 x 300mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS:13755 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete.

Providing and laying polished Vitrified tiles in different sizes (thickness to be spcified by manufacturers) with water absorption's less than .08% and confirming to IS : 15622 pf approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4)1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc, complete.

Size of tile 50x50 cm

Size of tile 60x60 cm

Chequerred precast cement concrete tiles 22mm thick in basement floor & ramp floor jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand)

Medium shade using 50% white cement 50% grey cement.

SUB HEAD - 7 MARBLE WORK :-

Providing and fixing 18 mm thick mirror polished (PREMOULDED AND PREPOLISHED), machine cut, granite stone for kitchen platforms , vanity counters, window sills, facias and similar location of required size of approved shade, laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement , mixed with matching pigment, epoxy touch-ups including rubbing, curing , moulding and polishing to edge to give high gloss finish etc complete at all levels.

Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble.

Area of slab upto 0.50 sqm.

Granite of any colour and shade

Area of slab upto 0.50 sqm

Area of slab over 0.50 sqm.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Marble Work

Granite Work

Extra for fixing marble/ granite stone over and above corresponding basic items, in facia and drops of width upto 150mm with epoxy resin based adhesive including sleaning etc complete.

Extra for providing opening of required size & shape for wash basins / kitchen sink in kitchen platform, vanity counters and similar location in marble / Granite / stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Mirror polishing on marble work / granite work / stone work where ever required to give high gloss finish complete.

Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50 cm deep and 1.8 cm thick fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.

Granite Stone of approved shade.

SUB HEAD - 8 CLADDING WORK :-

Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately.)

Red sand stone.

White sand stone

Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut with machine cut edges sand stone) on walls at all heights using M.S. square/ rectangular tube in the required pattern as per architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle iron/ flats etc. which shall be welded to the frame and embedded in brick wall with cement concrete block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of necessary centring and shuttering and with approved expansion hold fasteners on CC/RCC surface, including drilling necessary holes. Approved cramps/ pins etc. shall be welded to the frame work to support stone cladding, the steel work will be given a priming coat of Zinc primer as approved by Engineering- charge and painted with two or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the Engineer-in-charge for approval before execution). The frame work shall be fixed in true horizontal & vertical lines/planes. (Only structural steel frame work shall be measured for the purpose of payment, stainless steel cramps shall be paid for separately and nothing extra shall be paid).

Providing and fixing adjustable stainless steel cramps of approved quality and of required shape and size adjustable with stainless steel nuts bolts and washer (total weight not less than 260 gms) for dry stone cladding fixed on frame work at suitable location including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge.

SUB HEAD - 9 STEEL WORK:-

Steel work welded in built-up sections / framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladders, railings, brackets, gates & similar works.

Providing and fixing hand rail by welding etc. to steel ladder railing, balcony railing & staircase railing including applying a priming coat of approved steel primer.

MS Tube

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

SUB HEAD - 10 STONE WORK :-

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like. Cement mortar 1:6 (1 cement : 6 coarse sand)

SUB HEAD - 11 ROOFING :-

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.80 mm thick with zinc coating not less than 275 gm/m²

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275 gm/m²

Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. 0.80 mm thick with zinc coating not less than 275 gm/m²

Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound, laid over a bed of 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete.

Providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm ..........

12.5 mm thick tapered edge gypsum board conforming to IS: 2095- Part I,

SUB HEAD - 12 FINISHING:-

12mm cement plaster of mix :-

a) 1:6 ( 1 cement : 6 fine sand)

15mm cement plaster on the rough side of single or half brick wall of mix

a) 1:6 (1 cement : 6 fine sand)

6mm cement plaster to ceiling to mix :-

a) 1:3 (1 cement : 3 fine sand)

White washing with lime to give an even shade:-

a) New Work (three or more coats)

Distempering with Oil Bound washable distemper of approved brand and manufacture to give an even shade

a) New work (Two or more coats ) over and including priming coat with cement primer

Finishing walls with water proofing cement paint of required shade :

New work (Two or more coats applied @ 3.84 kg/10 sum).

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:-

a) Two or more coats on new work

Washed stone grit plaster on exterior walls of height upto 10 M. above level in two layers,under layer 12mm cement plaster 1:4 (1 cement : 4 coarse sand ) furrowing the under layer with scratching tool,applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement : 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in - charge (Payment for providing grooves shall be made separately)

Providing and fixing double scaffolding system (cup lock type) on the exterior side, upto seven story height made with 40mm dia. M.S. tube 1.5 m centre to centre horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as .....

Acrylic Emulsion Paint

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture

POP punning

Providing and applying plaster of paris (super fine quality) punning with minimum thickness of 6mm and finish the surface smooth in line and level including scraping and hacking the existing finished surfaces, scaffolding etc. complete as per drawing.

POP cornice

Providing and making decorative plaster of paris (super fine quality) cornice (cast in situ), moulding, flutings etc in the required profile and smooth in line and level to the entire satisfaction of Project Manager complete as per design and drawing.

Width above 75 mm to 100 mm

SUB HEAD - 13 SANITARY FIXTURE & FITTINGS , DRAINAGE WORKS :-

Making soak pit 2.5 m diameter 3.0mtr deep with 45x45 cm dry brick honey comb shaft with bricks of class designation 75 and SW drain pipe 100mm diameter 1.8m long complete as per standard design.

with FPS bricks

Coursed rubble masonry with hard stone (first or second sort) in superstructure above plinth level and upto floor five level.Masonry work (first sort), in cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing 2nd class teak wood plain lining tongued and grooved, including wooden plugs complete with necessary screws and priming coat on unexposed surface.40 mm thick

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand)

18mm thick cement plaster in two coats under layer 12mm thick cement plaster 1:5(1cement :5 coarse sand) finish with top layer 6mm thick cement plaster 1:6 (1 cement : 6 fine sand).

Finishing walls with textured exterior paint of required shape

New work ( two or more coats applied @ 3.28 ltr / 10sqm ) over and including base coat of water proofing cement paint applied @ 2.20kg/ 10sqm

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sum mixed with water proofing cement compound @ 0.253 kg/sum. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sum mixed with water proofing cement compound @ 0.126 kg/sum. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

SUB HEAD - 10 SANITARY FIXTURE & FITTINGS , DRAINAGE WORKS :-

Providing and fixing white viterous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & CP flush bend with fittings & CI brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required:

W.C. pan with ISI marked white solid plastic seat and lid.

Providing, fixing, testing & commissioning of ABS Rinsing spray with regulator of approved quality with plastic flexible pipe 1.5 m long, wall hook complete as required of approved make Cera/ Jaquar/Parryware or equivalent and per Engineer in Charge

Providing and fixing water closet water closet squatting pan (Indian Type W.C Pan) with 100mm sand cast iron 'P' or 'S' trap, 10 ltrs low level, PVC flushing cistern with manually controlled device (handle lever)conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever requiredand as per direction of Engineer -In-charge:

White Vitreous China Orissa pattern W.C pan of size 580 x 440 mm with integral type foot rests.

Providing and fixing C.P. brass short body bib cock with flange of approved quality confirming to IS: 8931

15mm nomonal bore

Providing and fixing wash basin with CI/MS brackets, 15mm CP brass pillar taps, 32mm CP brass waste of standard pattern, including painting of fitting and brackets, cutting and making good the walls wherever required.

White Vitreous China wash basin (oval) size550 x 400 mm with single 15mm CP brass pillar tap

White Vitreous China flat back wash basin size550 x 400 mm with single 15mm CP brass pillar tap

Providing and fixing of 15mm dia brass single lever mixer set for bash basin including wall flange and cutting & making good the wall as required, of approved make as per direction of Engineer in Charge.

Providing & fixing PTMT Bottle trap for wash basin and sink

Bottle trap 38mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 263gms.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with CI brackets and stainless steel plug 40 mm including painting of fitting and brackets, cutting and making good the walls wherever required:

Kitchen sink with drain board

510 x 1040 mm bowl depth 250mm

Providing, fixing, testing and commissioning of C.P. brass wall / counter mounted sink mixer with C.P. wall flange, overhead swinging spout complete as required and making good the wall as required, of approved make as per direction of Engineer in Charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass union and G.I clamps complete, including painting and brakets, cutting and making good the walls and floor wherever required

One urinal basin with 5 litre white PVC automatic flushing cistern

Rangeof two urinal basin with 5 litre white PVC automatic flushing cistern

Range of three urinal basin with 10 litre white PVC automatic flushing cistern

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms

Providing and fixing C.P brass 4 way divertor for concealed fitting with built in non-returned valve with diverter handle mixer with spout and wall flange and cutting and making good the wall as required of make Jaquar Continental, Perryware or equivalent as per direction of Engineer in Charge.

Providing and fixing C.P. brass quality angle valve15 mm dia. For basin mixer and gyser points of approved quality, confirming to IS : 8931

15mm nomonal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make confirming to IS : 8931.

15mm nomonal bore

Providing & fixing PTMT liquid soap container109mm wide,125mm high and 112mm distance from wall of standard shape and brackets of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms.

Providing & fixing PTMT towel ring trapezoidal shape 215 mm long,200mm wide with a minimum distance of 37mm from wall face with concealed fitting arrangement of approved quality and colour weighing not less than 88 gms.

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.

Providing & fixing 600x450mm beveled edge mirror of superior glass ( of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washer complete.

Providing and fixing toilet paper holder

C.P. brass

Providing and fixing stainless steel twin coat hook fixed to wooden cleats with CP brass screws. (Make- as per direction of Engineer in Charge.

Providing and fixing raised toilet seat with cover for handicap toilet

Providing and fixing 35 mm dia powder coated steel grab bar.

Providing and fixing solid state, no touch operting, fully hygienic hand drier of approved shade with single blower, with time delay, summer & winter control, music while drying, volume ON/OFF controls including providing necessary brackets, cable from drier to Plug, Plug top key and lock etc, complete as required of approved Make- as per direction of Engineer in Charge.

Providing and fixing white vitreous china laboratory sink with rubber plug 40mm C.P brass waste and 40mm C.P brass trap with necessary C.P brass unions complete including painting of fitting and brackets, cutting and making good the walls wherever required:

Size 450x300x150mm

Providing and fixing soil, waste and vent pipes:

100 mm dia

Centrifugally cast (spun) iron socketed pipe as per IS 3989.

Centrifugally cast (spun) iron socketed pipe as per IS 3989

Providing and fixing M.S holder-bat clamps of approved design to sand cast iron/sand cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix ( 1cement:2coarse sand: 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc

For 100 mm dia pipe

For 75 mm dia pipe

Providing and fixing bend of required degre with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

Centrifugally Cast (Spun)Iron S & S pipe as per IS : 3989

Providing and fixing plain bend of required degree

Centrifugally Cast (Spun)Iron S & S pipe as per IS : 3989

Centrifugally Cast (Spun)Iron S & S pipe as per IS : 3989

Providing and fixing single equal plain junction of required degree with access door, insersion rubber washer 3 mm thick, bolts and nuts complete.

Sand cast iron S & S as per IS 3989

Sand cast iron S & S as per IS 3989

Providing and fixing single unequal plain junction of required degree.

Sand cast iron S & S as per IS 3989

Providing and fixing double equal plain inverted branch of required degree

100x100x100x100 mm

Sand cast iron S & S as per IS 3989

Providing and fixing terminal guard.

Sand cast iron S & S as per IS 3989

Sand cast iron S & S as per IS 3989

Providing and fixing collar

Sand cast iron S & S as per IS 3989

Sand cast iron S & S as per IS 3989

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter:

Providing and fixing M.S stays and clamps for sand cast iron / Centrifugally Cast (Spun) Iron Pipes iron pipes of diameter.

Providing and fixing trap of self cleaning design with screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors:

100 mm inlet 100 mm outlet

Sand cast iron S & S as per IS 3989

100 mm inlet 75 mm outlet

Sand cast iron S & S as per IS 3989

Providing and fixing G. I. floor drain consisting of 100x50 mm G. I. elbow (grating and G. I. pipe to be paid separately), complete as per instruction as per direction of Engineer in Charge.

Providing and fixing Heavy class SS grating with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for waster and FT.

Size 100 mm x 100 mm

Size 150 mm x 150 mm

Providing and fixing in position G.I. pipe and fittings of heavy class (c) conforming to IS:1239 (for waste pipe from individual fixtures to floor trap / floor drain & vent pipe) Including fixing at wall / ceiling level supported by galvanized clamps and hangers providing two coats of synthetic enamel paint of approved shade as per pipe colour code over a coat of primer or cutting & chasing in wall & floors, providing protection to embedded GI pipes & fittings by wrapping of 400 microne polythene sheet over two coats of bitumen including proper overlaps in joints complete as required and making good the chase by using 1:1 cement mortar as per direction of Engineer in charge

32 mm dia.

40 mm dia.

50 mm dia.

Providing and fixing uPVC sloted pipe 6 kg/sqcm working presure conforming to IS:13592 including fitting and clamps complete as per direction of Engineer in Charge.

200 mm dia.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge.

Internal Work - Exposed on wall

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 M spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge.

Concealed work including cutting chases and making good the walls etc.

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings. This include jointing of pipes & fitting with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in charge.

External Works

50 mm nominal outer dia Pipes

62.50 mm nominal outer dia Pipes

Providing & fixing ball valve (brass) of approved quality, High or low pressure with plastic floats complete

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

Providing & fixing gun metal gate valve with C.I wheel of approved quality, (Screwd end)

32 mm nominal bore

40 mm nominal bore

50 mm nominal obore

fixid wating chair in PFC

Fixed Waiting Chairs Multiple three seater heavy duty bench made of mild steel, duly powder coated , (CoroE sion U.V ray resistant coating ) perforated seat and back, duly cushioned having four legs with level adjusters seat and back upholstered in leatherite Size Length 68" Height-32" Width 28" as approved by the Deptt.

Cloak Room Lockers Suplying & Fixing in position Locker made of heat, bacteria, water, chemical, scratch and impact resistant 03mm & 09 mm thick solid compact laminate panels including doors, self, side pannel, Top & Bottom panels finished with approved texture/shade as per the detail drawings & as per IS 2046(Indian Standard). The compact lam should have Green Guard Certificate. It should be anti-bacterial duly certified . This also includes providing and fixing in position necessary hardware made out of Alluminium(Grade-6063-T6) & Stainless steel (grade-304) (1) Camlock (2) Hinges (3) Front Section (4) Back Section, (5) Infill Section (6) Rubber Lining (9) Screws & Nut bolt Locker shall be constructed with 4 alluminium interlocking supporting frame work, making it strong and rigid 1.01- Standard dimension of locker unit shall be: Width 300mm X Depth 450mm X Height 1800mm; ( Locker: 1, 2,3,4,5 , 6 & Z Shaped) Locker-Tier-4-Suede (Thickness 9mm x 3mm, Door 300x443, Divider Height -NA-, Overall Height 1880, Depth 450, Width -NA-) MAKE as approved by the Deptt.s & Design Consultant as required.

Water ATM A) Water filtration system - 5 stage UV B) Ultra filtration capacity – 250 ltr./hr C) Hot & Normal Water D) Storage tank – 400 ltr. E) Water Tank – SS 304 F) Outer body – SS 304 G) Puff insulation with cyclopenten technology H) Power consumption 1500W with 100% copper heater system I) Fully automatic warm water controller J) Volt – 220V single phase K) Outer structure – SS 304 with 3mm ACP L) Warranty – 1 year MAKE:- as approved by the Deptt.s & Design Consultant as required

Rejuvenation of Temple Verandah with Wood Flooring for temple Parikrama , Gangotri

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Supplying chemical emulsion in sealed containers including delivery as speciffied

SUB HEAD - 3 FLOORING WORKS :-

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).Sal wood

38 mm thick wood block flooring of first class teak wood laid over 25 mm thick leveling layer of cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 10 mm nominal size) to be paid separately, coated with a thin layer of hot bitumen penetration 80/25 (blown type) @ 2.45 kg per sqm, including fixing blocks in position after dipping in hot bitumen (blown type) up to half depth, planed, levelled smooth and finished complete.

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with :

Second class teak wood

Providing and laying of stone set pavement over 2.5 cm thick bedding layer of PCC 1:2:4 which shall further be placed over 10 cm thick dry stone kharanja or crushed stones base over a prepared subgrade as per drawings and technical specifications. The size of stones shall not be less than 20 cm x 20 cm and thickness of stones shall vary from 10 cm to 15 cm. The work includes filling of joints with PCC 1:2:4 as per the standard drawings and instructions of the Engineer-in-Charge

Sub Surface Drains with Perforated Pipe (Construction of subsurface drain with perforated pipe of 100 mm internal diameter of metal/ asbestos cement/ cement concrete/PVC, closely jointed, perforations ranging from 3 mm to 6 mm depending upon size of material surrounding the pipe, with 150 mm bedding below the pipe and 300 mm cushion above the pipe, cross section of excavation 450 x 550 mm.

Construction of Entry Gate (1nos), Gangotri

SUB HEAD -2 CONCRETE WORK :-

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in mouldings as in cornices, windows sills etc, including setting in cement mortar 1:3 (1 cement : 3 coarse sand) cost of required centering, shuttering but, excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

SUB HEAD - 8 FINISHING:-

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :White sand stone - exposed face fine dressed with rough backing

Stone work, plain in copings, cornices, string courses and plinth courses, upto 75 mm thick in Cement mortar 1:6 (1 cement : 6 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade

Construction of covered Poly Carbonate Roof from VIP parking to temple , Gangotri Temple

SUB HEAD -2 CONCRETE WORK :-

1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

SUB HEAD - 5 ROOFING :-

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110mm Dia

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler 110mm

Bend 87.5° 110mm Bend

Providing and fixing Unplasticised -PVC pipe clips of approved design to Unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent clear or pigmented, textured or smooth as specified. 2 mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6" ) as specified

Changing Rooms at the Ghat (1nos), Gangotri

SUB HEAD - 11 ROOFING :-

Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : Decorative veneer facings of approved manufacture

Public Convenience, Gangotri

Providing & fixing gun metal gate valve with C.I wheel of approved quality, (Screwd end)

65 mm nominal bore

Providing and placing on terrace (at all floor levels polyethylene water storage tank ISI : 12701 marked water storage tank with cover and suitable locking arrangement and making necessary holes for inlet outlet and overflow pipes but without fittings and the base suport for tank

Constructing masonary chamber 30x30xx50 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement : f fine sand) for gate valve with C. I. susface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1 : 3 ( 1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design with F. P. S. bricks

Informational & Directional Signages , Stone Benches & Solar Lights, Gangotri

Direction and Place Identification Signs with size more than 0.9 sqm Size Board. Providing and erecting direction and place identification sign with corrosion resistant 2mm thick DG Grade Type XI retro- reflective cautionary, mandatory, informatory sign board with 10 year warranty as per IRC:67 made of high intensity sheeting fixed over ACP (Aluminium Composite Panel) 3 mm thick (including framing and bracing with fabrication, plotting of letters on Electro cut film, pasting, riveting, taping and nut, bolts, washers and rivets etc for fixing), with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing. (Clause No. 801 of MORTH) as per design provide by engineer in charge

Stone Benches Size 1300m*425m*450mm thickness 50mm Material : Natural stone marble Makrana adanga Grey in colour to be designed as per refrence image attached. Note: All Material to be well considered as Natural stone not Artificial stone (10% of tolerance in colour size will be excepted) and as approved by the Deptt. & Design Consultant as required.

Pious Waste Management Supply and Installation of Fully Automatic Composter Machine with Platform & Shed to be made in civil converting organic waste into compost/havan samagri as approved by the Deptt & Design Consultant as required. Specification of the Machine Input Capacity: 2000 kg per day Type of Machine/Mode of Operation: Fully Automatic Compost Machine, Aerobic Method Process: Continuous Type of Waste: Horticulture Waste+ Flower Waste Body and Vessel Material: SS/MS Machine Protection System: Entire Machine system should have overload,current and hard material reject/protection system inbuilt. Emergency Features like Sensors, Auto Stop is recommended Control Panel: Only High Quality Brand like Schneider, ABB, L&T, Siemens etc. Processing Time: 24-48 Hours. Compost should be ready to use within 5 days. Waste feeding and Compost Removal Mechanism: Manual No Odor, Harmful Emission of Gas Power Requirement: 3 Phase Electricity Connection, 24 KW +/- 5% Comprehensive Warranty Period: 2 years Provide Maintenance Support for 2 years and on call service within 48-72 hours. Provide Training to the Labors employed by the Buyers for 10 days.

Dustbins (OUTDOOR STAND BIN) 1 BIN WALL THIKNESS 2.5mm ±1 mm THK. HDPE 01 2 LID WALL THICKNESS 2.5 mm ±1 mm THK. HDPE 01 3 VER. SQ. PIPE 50 X 50 X 1000 / THK. 10 GUAGE M.S. 02 4 HORI. SQ. PIPE 50 X 50 X 600 / THK. 10 GUAGE M.S. 02 5 BASE ANGLE 35 X 35 X 305 / 2mm THK. M.S. 03 6 M.S. BIN FRAME 30 X 5mm THK. M.S. 02 7 BOTTOM STRIP 100 X 100 X 3mm THK. M.S. 02 8 HOLDING ROD Ø25 X 100 M.S. 04 9 LOCKING ANGLE 40 X 40 X 50mm /3mm THK. M.S. 02 10 LOCKING PIN - STD. 02 11 HOLLOW SPARE - STD. 04 12 LOCKING PIN CHAIN - STD. 02 13 HINGE 35 X 3 mm 14 HANDLE 25 X 217 X 3mm THK. 02 15 HOLDING ROD SUPPORT PIPE Ø32 X 50 X 5mm THK. M.S. 04 16 RIVETS - - 18 17 HINGE BRACKET - M.S. 02 MAKE:- as approved by the Deptt.

Parking, Mukhwa

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete.

Cast in Situ Cement Concrete M 20 Kerb with Channel(Construction of cement concrete kerb with channel with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M10 grade foundation 150 mm thick, kerb channel 300 mm wide, 50 mm thick in PCC M20 grade, sloped towards the kerb, kerb stone with channel laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 408) Using Concrete Mixer

Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 50mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10mm wide filled with same mortar including ruled pointing etc. complete as per direction of engineer-in-charge.

M/S ARUN CONSTRUCTION