PROVN COMPOUND WALL AROUND KSP AREA INCLUDING CERTAIN REVENUE WORKS AT KANCHRAPARA MIL STN UNDER GE BARRACKPORE

Amount

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep and getting out in soft/loose soil complete all as specified and directed.

Surface dressing in soft /loose soil not exceeding 15 cm deep (averaging 7.50 cm deep) complete all as specified and directed.

Returning, filling in, including spreading leveling, watering and well ramming in layers not exceeding 25cm in soft/loose soil complete all as specified and directed.

Removing of excavated surplus soil exceeding 50m but not exceeding 250 m and depositing where directed at a level not exceeding 1.5m above the starting points in soft/loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) each not exceeding 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for PCC (1:2:4) type B-2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for RCC M-25 (design mix) (using 20mm graded stone aggregate) as in foundations including rafts, footings, foundations beam, plinth beams, bases for columns etc , basement slabs, under-reamed piles and mass concrete etc complete all as specified and directed.

M&L for RCC M-25 (design mix) (using 20 mm graded stone aggregate) as in column, piller, piers, post and struts etc complete all as specified and directed.

M&L for RCC M-25 (design mix) (using 20 mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed.

M&L for TMT bars 10 mm dia and over cut to length bent to shape as required including cranking, bending spirally for hoping for columns, hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L for from work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc for flat, rough finish surface of concrete complete all as specified and directed.

M&L for form work to sides of concrete foundation, footing, base of column, raft & plinth beam for flat, rough finish surface of concrete complete all as specified and directed.

M&L for form work to sides of pillar, posts, struts, piers, columns and stanchions for flat, rough finish surface of concrete complete all as specified and directed.

M&L for brickwork with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:4) on brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for applying three coats of white wash on surface of wall including preparation of new plastered surface complete all as specified and directed.

S&F for angle iron works as in post and struts in fencing post including cutting tops to shape as directed, drilling holes, bolting or riveting, notching for wire etc complete conforming to Fe. 290 Gde E-165 all as specified and directed.

S&F for galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings & straining & fixing to any type of standard rails straining bolts, including, securing or tying at crossings with & provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and directed (Each line of wire to be measured).

M&L for applying two coats of synthetic enamel paint over and including a coat of red oxide primer after preparation of new steel surfaces of any description over 10cm width or girth complete all as specified and directed.

M&L for providing, cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) as in coping finished the surface even and smooth complete all as specified and directed.

S&F for steel work in tubular trusses and purlins including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed.

S&F for rolled mild steel plates (plain or chequred) channels, square cut or notched (ordinary and counter sunk) forming holes with riveted, bolted or welded attachment of Fe 410-W (Gde E-250) quality A complete all as specified and directed.

S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of 0.50mm thick of any colour as approved by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F for pre-painted galvalume aluminium zinc coating GI based plain steel sheet of 0.50mm thick of any colour as approved by GE having tensile strength of 550 Mpa as in ridge wall/cladding, fixed with self tapping screws complete all as specified and directed.

M&L for broken brick hardcore of gauge not exceeding 63mm, deposited spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100 mm thick cement concrete (1:2:4) type B-2 (using 40mm graded crushed stone aggregate) as in floor finishing the surface even and smooth complete without using extra cement all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6) complete all as specified and directed.

M/S D K Singha

DEYS ENTERPRISE

azad enterprise

INDUSTRIAL CONSTRUCTION

M/S H.P Singha

NANDY ENTERPRISE

M AND D CONSTRUCTION