Replacing broken Cast Iron drainage pipes by PVC pipes in toilet shaft, providing upvc pipes in toilets and other misc. civil works in TE bldg. Gulbai Tekra, Ahmedabad

Amount

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing SS jali of size 150x150mm for floor trap all complete as per direction of Engineer in charge.

Providing and fixing UPVC (Schedule 80) pipes, including all UPVC plain fittings, including fixing the pipe with clamps. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

20 mm nominal bore

25 mm nominal bore

40 mm nominal bore

Providing and fixing UPVC valve of approved quality :

25 mm nominal bore

40 mm nominal bore

Providing and fixing UPVC (Schedule 80) brass threaded FTA/MTA/Elbow/Coupler of size 20mm nominal dia.

Providing and fixing UPVC (Schedule 80) brass threaded FTA/MTA/Elbow/Coupler of size 25mm nominal dia.

Providing and fixing UPVC (Schedule 80) brass threaded FTA/MTA/Elbow/Coupler of size 40mm nominal dia.

Providing and fixing 15mm nominal bore PTMT bib cock / stop cock / angle cock of "Prayag" or equivalent make all complete as per direction of Engineer in Charge.

Providing and fixing 15mm nominal bore PTMT pillar cock of "Prayag" or equivalent make all comple as per direction of Engineer in Charge.

Dismantling C.I. drainage pipe including removing Tee / Y Tee from wall without damaging the connected NT or P trap of WC and stacking the material within 50 metres lead :

75 mm dia pipe.

100 mm dia pipe

Providing and fixing on wall face unplasticised Rigid PVC drainage pipes conforming to IS : 13592 Type B, including jointing with solvant cement all complete as per direction of Engineer in Charge.

75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC dainage pipes, jointing with solvant cement and connecting with existing cast iron NT or P trap of WC with cement, Mseal etc. and plugging the hole with cement mortar all complete as per direction of Engineer in Charge

Single tee without door including one coupler

Cowel

Floor Trap

100mm inlet and 75 mm outlet

Providing and fixing clamps made of MS flat 20x5mm and fixing to wall by Jasti Killa (Nails) for supporting PVC dainage pipes including painting with red oxide paint all complete as per direction of Engineer in Charge

75 mm dia pipes

110 mm dia pipes

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspectionof work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment shall be made once irrespective of duration of scaffolding.Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done.

Cleaning of Manholes, Floor Traps, Gully Traps and connected sewer/ drainage lines by rodding, passing bamboo strips etc. including removal of sludge, rubbish etc. and disposal of the same all complete as per direction of Engineer-in-charge. (Manholes should be cleaned by mechanical means such as bucket rixa, suction pump etc. and no labour shall be allowed to enter Manholes)

Manhole up to 1.5m deep.

Manhole above 1.5m deep.

Gully Trap

Floor Trap/Nahni Trap

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Labour charges for engaging Plumber / Carpenter for attending complaints all complete as directed by Enginner-in-charge.

Labour charges for engaging labour for assisting Plumber / Carpenter for attending complaints all complete as directed by Enginner-in-charge.

Providing and fixing uplasticised PVC connection pipe with CP brass unions, 60 cm length, 15 mm nominal bore all complete as per direction of engineer in charge.

Providing and fixing UPVC (Schedule 80) brass threaded reducer elbow of size 20mmx15mm nominal dia.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink without drain board

610x460 mm bowl depth 200 mm.

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.

Polishing kota stone kitchen platform all complete as per direction of Engineer in charge.

Providing and fixing shelve cabinet of size 8'6"(L)x18"(W)x2'6"(H) made with 18mm plywood. Equal width Six number of shutters to be provided, one middle shelve shall be provided. Back side of cabinet will be made with 8mm plywood. Cabinet bottom shelve shall be 3" above ground. Top of cabinet with two layer of 18mm plywood to be provided. All inside of shelve cabinet shall covered with 1mm thick laminate sheet of approved pattern and design. All outside except back side of cabinet shall be covered with 4mm thick veneer of approved pattern and design. Shutters shall be fixed with 02 nos. heavy duty auto hinges. Groove shall be provided at shutter top edge for opening. Coast of all material and labour involved is included in the item, all complete as per direction of Engineer in charge.

Providing and fixing shelve cabinet of size 4'0"(L)x18"(W)x2'6"(H) made with 18mm plywood. Equal width four number of shutters to be provided, one middle shelve shall be provided. Back side of cabinet will be made with 8mm plywood. Cabinet bottom shelve shall be 3" above ground. Top of cabinet with two layer of 18mm plywood to be provided. All inside of shelve cabinet shall covered with 1mm thick laminate sheet of approved pattern and design. All outside except back side of cabinet shall be covered with 4mm thick veneer of approved pattern and design. Shutters shall be fixed with 02 nos. heavy duty auto hinges. Groove shall be provided at shutter top edge for opening. Cost of all material and labour involved is included in the item, all complete as per direction of Engineer in charge.

Providing and fixing corner shelve cabinet of size 18"(L)x18"(W)x7'6"(H) made with 18mm plywood and 12mm glass. Two sides of shelve will be of 18mm plywood meetig at right angle. Two sides upto 6" width will be of 12mm glass fixed to two sides of 18mm plywood. Front will of 12 glass supported on pivots. Three nos. 12mm glass shelves to be provided supported of "D" clamps. Bottoom and top shall be 18mm plywood. Cost of all material and labour involved is included in the item, all complete as per direction of Engineer in charge.

Providing and fixing shutters along with frame to cover electric panels of size 44"(W)x84"(H) . The shutters will be double leaf made with 18mm plywood. Frame for supporting shutters will also made from 18mm plywood. On top part louvers are to be provided in shutters. Inside of sutters to be enamel painted. Outside of shutters along with supporting frame to be covered by veneer of approved pattern and design.Cost of all material and labour involved is included in the item, all complete as per direction of Engineer in charge.

Providing and fixing shutters along with frame to cover electric panels of size 58"(W)x30"(D)x10'0"(H) . The shutters will be double leaf made with 18mm plywood. SIde box frame for supporting shutters will also made from 18mm plywood. On top part louvers are to be provided in shutters. Inside of sutters to be enamel painted. Outside of shutters along with supporting frame to be covered by laminate of approved pattern and design.Cost of all material and labour involved is included in the item, all complete as per direction of Engineer in charge.

Providing and fixing framework to support false ceiling. Length of framework will be 3.80m , height 0.30m and width 0.10m. Frame work will be made by 18mm plywood, consisting of two sides of height 0.30m, separatedby 0.10m, vertical supports 05 nos. Frame to be fixed at junction of false ceilings of two rooms. Cost of all material and labour involved is included in the item, all complete as per direction of Engineer in charge.

Providing and fixing one nos. 20mm thick kota stone shelve to wall by making groove in wall and filling joints wth cement mortar. Kota stone shelve be mirror polished on both sides, size will be 5'0"x1'0". Cost of all material and labour involved is included in the item, all complete as per direction of Engineer in charge.

Repairing MS grill platform at shaft by welding and fixing new members such as MS angle, square bars etc., making hole in RCC and pluggung hole with RCC after fixing MS Angle, all complete as per direction of Engineer in charge. (Cost of new MS member will be paid separately in relevant item)

Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,

shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)

Deduction for taking over of unserviceable materials obtained from dismantling / demolishing as is where is basis. Note : Materials shall be taken over by the contractor at his own cost and will allow to deduct at the quoted rate from the bill of payment.

15 mm nominal dia. Brass Bib/ stop/ angle cock

G.I. Pipe & fittings.

15mm dia. Pipe

20mm dia. Pipe

25mm dia. Pipe

40mm dia. Pipe

75mm dia. CI pipe

100mm dia. CI pipe

OM ENTERPRISES (BID ID -813491)