Construction of Office Building for Anthur Municipality

Amount

Building

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

2.7.1 : Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Ordinary rock

2.7.3 : Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Hard rock (blasting prohibited

2.26.2 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.Ordinary or hard rock

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.1.3 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

4.1.5 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

od21018/2023_2024 : Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. <br>All work upto plinth level

od50481/2023_2024 : Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. <br>All work above plinth level upto floor V level

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.9.19 : Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

50.6.7.1 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc.

50.6.7.2 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

50.6.7.3 : Laterate masonry with neatly dressed laterate stone of size 40x20x15 cm or nearest size in cement mortar 1:6 for superstructure above floor two level upto floor five level including all cost of materials, labour charges etc.

50.6.3.1 : Solid block masonry using pre cast solid blocks ( Factory made) of size 40x20x10cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth for 10 cm thick wall in CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding etc complete

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

od18719/2023_2024 : Solid block masonry using pre cast solid blocks ( Factory made ) of size 40x20x10cm or nearest available size confirming to IS 2185 part I of 1979 for Super structure above floor two level upto floor five level for 10cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand ) including cost of scaffolding etc complete

50.9.1.1 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood

50.9.3.1 : Providing and fixing paneled or paneled and glazed shutters for doors, windows and clerestory windows, 30 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding paneling which will be paid for separately, all complete as per direction 0f Engineer in- charge. using Anjili/ Jack wood

50.9.4.1 : Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured) paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality Anjili/ Jack wood

od18720/2023_2024 : Providing and fixing glazed shutters for doors using 10mm thick toughened glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Using Anjili wood / jack wood 30 mm thick shutters

9.117.1 : Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1 mm), with wall thickness 2.0mm (±0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 x 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification and direction of Engineer-in-chargeExtruded section profile size 48x40 mm

9.118.1 : Providing and fixing to existing door frames24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness,fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge( For W.C. and bathroom door shutter).

21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.2.1 : Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

21.3.1 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

9.147A.3 : Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately)<br> Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window double panels with top fixed with S.S. friction hinges (350 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. ( Area of window upto 2.50 sqm).

9.147B.1 : 543 SUB HEAD : 9 - WOOD & PVC WORK 9.147B Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately).<br> Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

9.97.1 : Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:300x10 mm

9.97.3 : Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:200x10 mm

9.81.1 : Providing and fixing bright finished brass handles with screws etc. complete:125 mm

21.16.2 : Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-Charge.Powder coated minimum thickness 50 micron aluminium

10.26.1 : Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.M.S. tube

10.17 : Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

10.25.1 : Item Shifted to head 14 as item 14.74Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In stringers, treads,landings etc. of stair cases, including use of chequered plate wherever required, all complete

10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

22.5 : Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

4.2.5 : Providing and laying cement concrete in retaining walls, return walls, walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing:1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size)

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

11.46.2 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

11.56.1 : Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

od18734/2023_2024 : Providing and laying antiskid floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.&lt;br&gt;Size of Tile 600 x 600 mm.

8.31 : Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

13.16.1 : 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

5.30 : Add for plaster drip course / groove in plastered surface or moulding to R.C.C. projections.

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

25.3 : Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement

25.1 : Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account).

Plumbing

17.10.1.1 : Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink with drain board510x1040 mm bowl depth 250 mm

17.10.2.1 : Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink without drain board610x510 mm bowl depth 200 mm

17.28.1.1 : Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC. waste fittings complete.Semi rigid pipe32 mm dia

17.32.2 : Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357 mm

18.21.1.1 : Providing and fixing uplasticised PVC connection pipe with brass unions:30 cm length15 mm nominal bore

18.53.1 : Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

18.65 : Providing and fixing PTMT Soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fittings arrangements, weighing not less than 106 gms.

17.16A : Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge

17.22A : Providing and fixing CP Brass 32mm size Bottle trap of approved quality & make and as per the direction of Engineer in charge.

18.7.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall20 mm nominal outer dia pipes

18.7.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall25 mm nominal outer dia pipes

18.7.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall32 mm nominal outer dia pipes

18.10.6 : Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work- Exposed on wall50 mm dia nominal bore

18.17.1 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

18.17.2 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore

18.17.3 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40 mm nominal bore

18.17.4 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore

18.19.3.1 : Providing and fixing gun metal non-return valve of approved quality (screwed end):40 mm nominal boreHorizontal

18.19.3.2 : Providing and fixing gun metal non-return valve of approved quality (screwed end):40 mm nominal boreVertical

18.33.1 : Constructing masonry chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement:4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 ( 1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S (non modular) bricks of class designation 7.5

18.17.1A : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :20 mm nominal bore

od18715/2023_2024 : Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (twin flush), conforming to low flow fixtures with green building norms with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

od18716/2023_2024 : Providing and fixing brass bib cock of approved quality having low flow fixture with green building category norms confirming to IS standards.

od18717/2023_2024 : Providing and fixing of 15 mm C.P. brass sink cock of low flow fixture category wall mounted with 188mm long swivel spout and wall flange having green building category norms including all fittings and brackets of approved quality

od18718/2023_2024 : Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps having low flow fixtures conforming to green building category norms , 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:&lt;br&gt;White Vitreous China Flat back wash basin size 550x400mm with single 15 mm C.P brass pillar taps

18.60.1 : Providing and fixing enclosed type water meter (bulk type) conforming to IS: 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. ( The tail pieces if required will be paid separately):80 mm dia nominal bore

17.5.2 : Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required:Range of two half stall urinals with 5 litre PVC. automatic flushing cistern

17.5.3 : Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required:Range of three half stall urinals with 10 litre PVC. automatic flushing cistern

21.12.2 : Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0mm thick & 2100 mm long with S.S. screws etc. complete as per direction of Engineer -in-Charge.Powder coated minimum thickness 50 micron aluminium tubular handle bar

od18721/2023_2024 : Supply and fixing of UPVC pipes and fittings / specials like tees, elbows, bends, unions, offsets, Hex nipples collars, cutting, threading the pipes with threading machine, jointing using holdtile and cotton thread or shallock and pressure testing the joints / pipeline for 10 kg/sq.cm hydraulic pressure, for 2 hours etc., including chasing in solid block masonry walls with groove cutting machine to required width and depth, making bores in walls, foundations and RCC slabs, making good the walls and bores in CC or CM&lt;br&gt;1:3 as applicable clearing the debris, grouting of concealed pipes, MS hooks for fixing pipes and making good the walls and floors.65mm dia

od18722/2023_2024 : Supply and fixing of UPVC pipes and fittings / specials like tees, elbows, bends, unions, offsets, Hex nipples collars, cutting, threading the pipes with threading machine, jointing using holdtile and cotton thread or shallock and pressure testing the joints / pipeline for 10 kg/sq.cm hydraulic pressure, for 2 hours etc., including chasing in solid block masonry walls with groove cutting machine to required&lt;br&gt;width and depth, making bores in walls, foundations and RCC slabs, making good the walls and bores in CC or CM 1:3 as applicable clearing the debris, grouting of concealed pipes, MS hooks for fixing pipes and making good the walls and floors 50MM DIA

od18723/2023_2024 : Supply and fixing of UPVC pipes and fittings / specials like tees, elbows, bends, unions, offsets, Hex nipples collars, cutting, threading the pipes with threading machine, jointing using holdtile and cotton thread or shallock and pressure testing the joints / pipeline for 10 kg/sq.cm hydraulic pressure, for 2 hours etc., including chasing in solid block masonry walls with groove cutting machine to required&lt;br&gt;width and depth, making bores in walls, foundations and RCC slabs, making good the walls and bores in CC or CM 1:3 as applicable clearing the debris, grouting of concealed pipes, MS hooks for fixing pipes and making good the walls and floors.40mm DIA

od18724/2023_2024 : Supplying &amp; Fixing at site in position Fabricated u PVC Astm Sch 40 Puddle flanges in the underground and overhead water tanks as per the requirement of the Engineer - in - charge - 100mm dia

od18725/2023_2024 : Supplying &amp; Fixing at site in position Fabricated u PVC Astm Sch 40 Puddle flanges in the underground and overhead water tanks as per the requirement of the Engineer - in - charge - 65mm dia

od18726/2023_2024 : Supplying &amp; Fixing at site in position Fabricated u PVC Astm Sch 40 Puddle flanges in the underground and overhead water tanks as per the drawings and the requirement of the Project Manager 50mm dia

od18727/2023_2024 : Providing, fixing, testing and commissioning of brass body nickel plated automatic air release valves with necessary GI Specials, thread, holdtight, brass spindle, NBR and elastomeric, stainless steel spring polypropylenic float at the top most points of water supply distribution ring main. 20 mm dia

od18728/2023_2024 : Supply and fixing of plastic ball float valve with gun metal lever of IS specification make and approved by the client / consultant for muncipal water inlet pipe to UG sump. 25 mm dia

od18729/2023_2024 : Supply and fixing of PVC multi inlet floor trap of self cleaning design moulded or fabricated, if not available in size mentioned below, with or without vent arm jointing with solvent cement followed by application of leak proof adhesive like FRP paste including encasing all round fixing the floor trap in cement concrete 1:2:4 ratio of size 300 x 300 mm x 250 mm height (approx) and making good the floors. 110mm dia

od18730/2023_2024 : Supplying and fixing at site in position PVC Rodding Eye (6 kg/cm2) complete in all respects. 160 mm dia

od18731/2023_2024 : Supplying and fixing at site in position PVC Rodding Eye (6 kg/cm2) complete in all respects.&lt;br&gt;110 mm dia

od18732/2023_2024 : Supplying and fixing at site in position PVC Rodding Eye (6 kg/cm2) complete in all respects.&lt;br&gt;75 mm dia (Supply and labour)

18.8.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal outer dia pipes

50.18.8.8.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2

50.18.8.9.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

50.18.9.8.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 6 Kgf/ cm2

50.18.9.9.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

50.18.9.10.1 : Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

50.18.9.17.2 : Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 63 mm dia 4 Kgf/cm2- External work - exposed on wall

50.18.9.18.2 : Providing and fixing PVC pipes including fixing the pipe with clamps/Clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 4 Kfg/cm2 - External work - Exposed on wall

50.18.9.19.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

50.18.9.19.2 : Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 m dia 4 Kgf/cm2 - External work - Exposed on wall

19.4.1.1 : Providing and fixing square-mouth S.W. gully trap class SP -1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P typeWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.7.1.2 : Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With Sewer bricks conforming to IS : 4885

19.8.1.2 : Extra for depth for manholesSize 90x80 cmWith Sewer bricks conforming to IS : 4885

50.18.8.6.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2

Tanks

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

2.7.1 : Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Ordinary rock

2.7.3 : Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Hard rock (blasting prohibited

2.26.2 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.Ordinary or hard rock

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.1.5 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.1.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

60.7.1 : DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site

19.18.1 : Supplying and fixing C.I with out frame for manholes:455 x 610 mm rectangular C.I cover ( light duty ) the weight of the cover to be no less than 23 kg

Trenches

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.1.3 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

10.25.2 : Item Shifted to head 14 as item 14.74Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Interlocking in Driveway

16.78.2 : Construction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

16.91.2 : Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Electrical 1

od48146/2023_2024 : 160kVA 11kV/433V Cast Resin (Dry type)USS Transformer &lt;br&gt;Supply, installation, testing &amp; commissioning of 160kVA 11kV/433V indoor cast resin dry type USS transformer (copper double wound) with HT Metering facility having a continuous rating for 11kV / 433V 3 phase 50 Hz. Transformer should have cable end box on HV side suitable for 3Cx185 sq.mm XLPE cable and suitable end box on LV side for connecting 4 runs of A2XFY Cables, with all accessories, complete as required as per State electricity board, ECBC, IE rules specifications. The transformer shall confirm to IS 2067/77, 11171/1985 with latest amendment etc complete. The USS shall be with 11kV, 26.3KA, 630A load break switch, with HT HRC fuses, 3 nos CTs of 0.2S class and suitable ratio as per contract demand, and 1 no PT of class 0.2 with provision for fixing TOD meter and output connected to 11kV seal off bushings to the transformer. Mechanical and electrical on / off indication are require Emergency off push button- 1No

od48148/2023_2024 : HT CABLE SUPPLY &lt;br&gt;Supply of following 11kV (E) grade XLPE insulated PVC sheathed compact circular armoured aluminium conductor HT power cable, insulation screened with extruded semi conducting compound in combination with&lt;br&gt;copper tape suitable for 11kV earthed system confirming to relavent standard. 3Cx185sq.mm

od48150/2023_2024 : Laying of following 11kV (E) grade XLPE insulated PVC sheathed compact&lt;br&gt;circular armoured aluminium conductor HT power cable, insulation screened with extruded semi conducting compound in separate existing cable tray/ on surface using factory made clamps and the spacing between clamps will not exceed 60cm. 3Cx185sq.mm

od48152/2023_2024 : 2 -POLE STRUCTURE&lt;br&gt;Supply, installation, testing and commissioning of State Electricity board incoming 2 pole structure which consists of required length HT Pre-stressed Concrete Poles (PSC), HT stay set complete, 11kV pin type insulator, channel cross arm, 11kV disc insulator with tension set, earth pipe with clamp ,GI :4mm dia wire, 9kV / 5kA Lighting Arrestor set, 200A Air Break switch with operating handle and locking mechanism, DO fuse set, supports, jumpers, interconnecting conductors and all required accessories complete as per State Electricity board requirements. The cost of the civil foundation not to be considered and shall be measured along with the civil items.

od48155/2023_2024 : EXHAUST PIPES&lt;br&gt;Supply, erection, commissioning of additional length of exhaust pipes with long radius bend from residential silencer with necessary clamps, fixtures, civil works for support and painted with heat resistant, rust proof, bituminous paint of approved colors to a maximum of 10 m in stages of following sizes including suitable rain cap for top to avoid rain water entry. The distance between exhaust pipe at top and rain cap should be higher than diameter of pipe. It is also recommended that horizontal run of exhaust piping should slope downwards away from engine to the condensate trap. Silencer should be installed with drain plug at bottom. Fixing shall be done with proper clamps, expansion bolts, and all other accessories as instructed by the Engineer and the rate inclusive of all minor civil works required, bolts, clamps etc as required for installation. Support to exhaust piping should be done in such a manner that load of exhaust piping is not exerted to turbocharger. Exhaust pipe height shall be 3m more than the top of any adjacent building withing 10m radius of the exhaust. A)100mm dia

od48156/2023_2024 : B) 125 MM DIA

od48157/2023_2024 : AUTOMATIC POWER FACTOR PANEL(50kVAr)&lt;br&gt;Rating of APFC Panel - 50KVAR ; Rated voltage of the Panel - 440V AC; Frequency - 50Hz; No. of Phases - 3 phase; Material - CRCA; Protection - IP 42/43; Application - Indoor; Painting - Shade Grey; Busbar details: Material - Aluminium; 125A, 415V best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Capacitors Type - MDXL; Heavy Duty Type, 3 Ph, 50Hz; No. of Steps -7; Configuration - (10kVARx3+5kVARx 4 ) &lt;br&gt; Incomer; 125 25kA TPN MCCB - 1No; RYB indication lamp and Digital VAF Meter- 1set; Outgoing a 10kVAR MD-XL; Heavy Duty Type Capacitors -3nos; 40A TP MCB - 3 nos; Capacitor Switching Contactor ( 40A ) -3 nos 5kVAR MD-XL Heavy Duty Type; Capacitors - 4 nos: 32A TP MCB - 4 nos: Capacitor Switching Contactor (32A ) - 3 nos; The banks and capacitors shall have CPRI test certificates. Supply Installation, testing and commisioning.

od48160/2023_2024 : Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor mounted, front operated MV panel board made out of 16 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided.Incomer - 160A 4P Isolator - 1 no.160A, 433V,best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Necessary interlocking arrangementRYB phase indicating LED lamps with control fuses and switches - 1 set.Three phase digital multifunction meter (class 1) with display of V,A,f,pf,power,energy, RUN &amp; ON hours, RPM with three number of current transformers. - 1 nosOutgoings63A 16kA TP Thermal Magnetic Based MCCB - 5 nos100A 16kA TP Thermal Magnetic Based MCCB -2 nos

od48161/2023_2024 : PLUMBING PANEL&lt;br&gt;Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor mounted, front operated MV panel board made out of 16 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. &quot;Incomer - 63A FP Isolator - 1 no. 63A, 433V, best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Necessary interlocking arrangement RYB phase indicating LED lamps with control fuses and switches &ndash; 1 set. Outgoings 40A TP MCB - 5 no. Supply, Installation, erection, testing and commissioning.

od48162/2023_2024 : LIFT PANEL&lt;br&gt;Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor mounted, front operated MV panel board made out of 16 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. &quot;Incomer - 63A FP Isolator - 1 no. 63A, 433V, best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Necessary interlocking arrangement RYB phase indicating LED lamps with control fuses and switches - 1 set. Outgoings 40A FP 100mA RCBO - 1 nos 25A 2P 30mA RCBO - 2 nos 6A SP MCB - 2 nos 16A SP MCB &ndash; 2 nos Supply, Installation, erection, testing and commissioning

od48163/2023_2024 : Supply and clamping of the following PVC sheathed unarmoured flexible power cable conductor of best conductivity copper solid/stranded conductor, XLPE insulated, PVC inner sheathed1.1kV grade strictly conforming to IS:1554 (Part-I)&lt;br&gt;1964 of the following sizes in cable tray /wall using factory made heavy gauge GI/painted MS clamps. Space between clamps not exceeding 60cms amd making good the damages colour washing etc as required. and instructed by engineer at site/consultant.&lt;br&gt;10Sqmm Flexible Cu Wire&lt;br&gt;1Cx10Sqmm Flexible Cu Cable

od48164/2023_2024 : 1Cx16Sqmm Flexible Cu Cable

od48166/2023_2024 : 4 sqmm 3 core PVC/ XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

od48167/2023_2024 : 6 sqmm 4 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

od48168/2023_2024 : 10 sqmm 4 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

od48169/2023_2024 : 16 sqmm 4 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

od48170/2023_2024 : 25 sqmm 4 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

od48171/2023_2024 : 35 sqmm 3.5 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

od48172/2023_2024 : 50 sqmm 3.5 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

od48173/2023_2024 : 70 sqmm 3.5 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

od48174/2023_2024 : 95 sqmm 3.5 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

od48175/2023_2024 : 150 sqmm 3.5 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

od48176/2023_2024 : 185 sqmm 3.5 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

od48177/2023_2024 : END TERMINATION&lt;br&gt;Supply and making end termination with brass double compression gland, earth clip and aluminum lugs/ Cu lugs for following size of PVC insulated and PVC sheathed/ XLPE aluminum conductor cable of 1.1kV Grade as reqiured. a)4Cx6sq.mm Al Cable

od48178/2023_2024 : b)3Cx4sq.mm Al Cable

od48179/2023_2024 : 6Cx2.5 sq.mm Cu Control Cable

od48181/2023_2024 : f)16Sqmm Flexible Cu Cable

od48182/2023_2024 : g)10Sqmm Flexible Cu Cable

od48183/2023_2024 : Supply of LED Terrace light BRP042 25W MR S1 PSU GR

od48185/2023_2024 : Supply of angle batten holder with LED Lamp

od48186/2023_2024 : Supply of 7.5W, High efficient recess mounted LED round down lighter with white powder coated, pressure die cast aluminium housing. High transmitting PS diffuser provides soft light. CRI greater than 80, IP20, Ambient temp-0 to 45DegC,&lt;br&gt;CCT - 4000/5700K, 50,000 hrs @ L70 life. Driver efficiency greater than 85%, THD less than10%, Power factor greater than0.9, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 90-265V AC and Safety Extra Low Voltage Safe levelness than 60V DC as per IEC standard

od48187/2023_2024 : Supply of LED bulk head WT202W LED6S NW PSU S3 PC with fittings

od48188/2023_2024 : Supply of LED Tube Light , PHILIPS make 20W BN 021 LED 22S 6500 PSU with fittings

od48189/2023_2024 : Supply of 13.5W, High efficient recess mounted LED round down lighter with white powder coated, pressure die cast aluminium housing. High transmitting PS diffuser provides soft light. CRI greater than 80, IP20, Ambient temp-0 to 45DegC, CCT - 4000/5700K, 50,000 hrs @ L70 life. Driver efficiency greater than 85%, THD less than10%, Power factor greater than0.9, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 90-265V AC and Safety Extra Low Voltage Safe levelness than 60V DC as per IEC standard

od48190/2023_2024 : Supply of Integral, SMD 2x2 LED, IP 20, 30W LED Recess mounted fixture with UGR less than19 and System efficacy of more than 105lm/W and system lumen output 3150lm. Luminaire shall have Microprecision Optics diffuser for Uniform illumination and wider light distribution to maintain UGR less than19. LM 80-08 compliant LEDs from reputed makes such as Nichia / Cree / Bridgelux / Lumileds should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall use SMD type LED. The LED shall be compliant with LM80-08 standard with L70 life of 50000 Hrs tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing). The LEDs used should be with CCT of 5700 K and CRI of Minimum 80. LED Driver shall be Multistage, Isolated type, APFC, Constant Current topology driver with proper heat sink for heat dissipation suitable to operate in input voltage range of 150V to 270V (nominal rated voltage &ndash; 240V) with 2KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. Complying to SELV less than 60V DC standards

od48191/2023_2024 : Supplying 5 star rated , BEE certified 26W, ceiling fan with BLDC motor, with super enamelled copper wire winding, 230 V, single phase 50 HZ remote control operated fan with 1200mm sweep and 3 blades including all accessories as required with remote and standard length downrod all accesories required for complete installation (Havells Efficienca Neo or equivalent)

od48192/2023_2024 : Supply of exhaust fan of 300mm sweep in the existing opening, including making good the damage, connection, testing, commissioning etc. as required, including all accessories as required for complete installation including shutter etc complete as required

od48193/2023_2024 : Supply &amp; installation of wall fan of 450 mm sweep Havells Airboll Hi-speed or equivalent) including all accessories as required for complete installation.

od48194/2023_2024 : 6 way (8 + 18) double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

od48195/2023_2024 : 8 way single phase phase double cover (IP 42/43) MCB DB

od48197/2023_2024 : RCBO&lt;br&gt;Supplying, fixing, testing and commissioning following four pole and double pole, 415 volts and 240 volts, residual current circuit breaker with overload protection (RCBO) of the following rating and sensitivity current in the existing MCB SPN and TPN horizontal/vertical DB&apos;s complete with connections, etc. as required and instructed by engineer in charge/consultant. 25A DP 30mA RCBO

od48199/2023_2024 : 32A 30mA FP RCBO

od48201/2023_2024 : CHANGE OVER SWITCH&lt;br&gt;Supply, installation, testing and commisioning of following rating Change Over Switch conforming to IEC 60947-3, IS/IEC 60947 -3, with CRCA sheet powder coated enclosure, complete with terminals and all accessories etc as required and as instructed by engineer in charge and making good any damages made during installation. 25A, 415V, FP COS

od48202/2023_2024 : 32A FP Isolator with enclosure

od48203/2023_2024 : 63A FP Isolator with enclosure

od48204/2023_2024 : MCB&lt;br&gt;Supply, installation, testing and commisioning of following rating TP C curve MCB, 10kA as per IS/IEC 60898-12002 in the existing MCB VDB/MCCB DB including all connections and iterconnections as required and as instructed by engineer in charge/consultant. 63A TP MCB

od48205/2023_2024 : 40A TP MCB

od48206/2023_2024 : POP - UP BOX &lt;br&gt;Supply, Fixing, testing and commisisoning of 4 module Matt black finish pop up box with slim design for perfect integration into furniture equipped with one number 6A socket and one number CAT 6 data socket supplied along with installation kits for table tops and all accessories as required for complete installation including making good any damages made, as instructed by engineer in charge, providing connections etc as required. (Legrand Arteor or equivalanet)

od48207/2023_2024 : EARTHING &lt;br&gt;Supply, installation and tesing of 1200mmx1200mmx12mm CI plate electrode earth station conforming to IS:3043-1987 / NEC / IEE complete with brick masonry chamber, CI cover, CI frame, GI watering pipe of 50 mm dia with funnel having 20G GI wire mesh etc. The CI cover frame/ chamber shall be of 1000mm x 500mm x 600mm size. CI manhole cover with frame shall be painted with bitumastic paint, identification of earthpit with yellow paint below the chamber cover, mixtures of charcoal &amp; common salt around electrode including digging of pit up to permanent moisture level but not less than 3 metre depth and back filling. (value of earth resistance should be less than 1 ohm)

od48208/2023_2024 : Supply, laying / fixing of earthing conductor of Cu strip/ wires jointing as per&lt;br&gt;IS:3043 / 87 in trench/walls pulling through pipes etc as required. 25x3mm Cu&lt;br&gt;strips tinned at the point of contact

od48209/2023_2024 : Copper wire No.8 SWG

od48210/2023_2024 : Copper wire No.10 SWG

od48211/2023_2024 : LIGHTNING PROTECTION&lt;br&gt;Providing and fixing of fully solid 3m Vertical Air terminal made up of Semi-hard (E-AlMgSiO5), 16mm rod tapered to 10mm. VAT 3 or Equivalent

od48212/2023_2024 : Providing and fixing of fully solid 4m Vertical Air terminal made up of Semi-hard (E-AlMgSiO5), 16mm rod tapered to 10mm. VAT 4 or Equivalent

od48213/2023_2024 : Providing &amp; fixing of Down conductor (8mm solid aluminium alloy round conductor) made up of Semi-hard (E-AlMgSiO5). SRC 8-AL or Equivalent

od48214/2023_2024 : Providing &amp; fixing of Terrace Conductor Fibre Reinforce Concrete holder for fixing horizontal air terminal. MBPCH8 or Equivalent

od48215/2023_2024 : Providing &amp; fixing of Down conductor (8mm solid aluminium alloy round conductor) made up of Semi-hard (E-AlMgSiO5). SRC 8-AL or Equivalent

od48216/2023_2024 : Providing and fixing of Stainless Steel SS 304 Wall Clamp to mount Vertical Air Terminal 1 meter to 4 meter. WC 16 SS or Equivalent

od48217/2023_2024 : Providing and fixing of Interception Tip made up of Semi-hard (E-AlMgSiO5) to provide on the top of Vertical Air Terminal. ITVAT or Equivalent

od48218/2023_2024 : Providing &amp; fixing of whether resistant Nylon Parapet Conductor Holder for fixing horizontal air terminal &amp; down conductors. The conductor holder has to fixed using fischer and SS Screws. PCH 8 or Equivalent

od48219/2023_2024 : Providing and fixing of Aluminium Alloy Ferrule T Connector to avoid bimetallic corossion. Crimping has to be done minimum in 9 points for strong bonding. CJT 8 or Equivalent

od48220/2023_2024 : Providing and fixing of Aluminium Alloy Expansion Piece to auto adjust climatic variations. EPC 8 or Equivalent

od48221/2023_2024 : Supply and fixing of 4 Kg ABC Dry Powder (Stored Pressure) Type Fire Extinguisher. pressurized with dry nitrogen gas at 15 bar. Design, construction and testing as per IS 2171-1999 external epoxy powder coating with PO Red Shade No. 538 of IS 5, Supplied with standard accessories

od48222/2023_2024 : Supply and providing 6 mm thick and 1 m wide electrical grade chequered type&lt;br&gt;rubber mat to withstand 3.3 kV dielectric strength conforming to IS 5429/1969

od48223/2023_2024 : Supply and providing First Aid Box

od48224/2023_2024 : Supply and providing laminated First Aid chart duly framed and placed in a conspicuous location for clear vision

od48225/2023_2024 : Supply &amp; fixing Laminated drawings of electrical lay out, schematic drawing etc on good frame work.

od48226/2023_2024 : Supply and providing MS chequered plate of suitable thickness including cutting, welding, painting etc. as required for cable duct covering etc

od48227/2023_2024 : Supplying and installing at approved location approved make fire buckets of 24 gauge galvanized steel sheet, standard 9 litre capacity and of round bottom shape, painted white inside and red outside and black on the bottom, inscribed with letters &ldquo;FIRE&rdquo; in black and gold. Cost shall be inclusive of providing MS stand for 2 nos of fire buckes, or , duly painted over a coat of primer.

od48228/2023_2024 : Supply of 1 pair 11 KV rubber hand gloves of approved make

od48229/2023_2024 : SAFETY EQUIPMENT&lt;br&gt;Supply and providing 12 mm thick and 1 m wide electrical grade chequered type rubber mat to withstand 11 kV dielectric strength conforming to IS 5429/1969

od48230/2023_2024 : Supply and fixing of modular 25A power socket placed in and including suitable size modular base and coverplate, mounted on suitable size modular GI/open PVC box, reccessed in the case of GI, fixing providing connections, testing and commisisoning and making good any damages made during installation as instructed by engineer in charge, including all accesories, connections and interconnections as required for complete installation

od48231/2023_2024 : PREPARATION OF ALL DRAWINGS &lt;br&gt;Getting necessary statutory approvals from all other government agencies, Preparation of all drawings submitting and getting approval from Electrical Inspectorate, submitting of Completion certificates and arranging inspection, getting sanctions and energisation certificates, test reports. Preperation of shop drawings for execution at site and getting the approved by engineer in charge/consultant before execution at site, preperation of As-built drawings of installation upon completion. Obtaining manuals, technical details,as-built/GA drawings of all equipments from concerned and also obtaining all necessary sanctions from relevant regulatory boards, submitting of test certificates of all equipments obtaining power allocation &amp; power connection etc. for commissioning of the whole installation in the premises. All statutory payments will be reimbursed on production of the original receipts.

od48232/2023_2024 : BIDIRECTIONAL HT TOD NET METER&lt;br&gt;Supply, Installation, testing &amp; commissioning of 3 phase 4 wire according to IS14697-1999, CBIP-325, IS 159595A, class: 0.2S, TOD meter with RS485 port, LCD with backlit display of Electricity board approved make, in existing enclosures of outdoor metering cubicle including all necessary accessories for fixing and connection complete as required getting tested and approved from statutory authorities, providing connection/inter-connections as required for complete installation and as instructed by engineer in charge/consultant. (Make - L&amp;T ER300P or equivalent)

od48237/2023_2024 : 40A 100 mA 4P RCBO

od48238/2023_2024 : Supply of BN 308 LED 40S 6500 L120 PSU WH

od48239/2023_2024 : 63A 100mA 4P RCBO

od48248/2023_2024 : Supply &amp; providing insulation for exhaust pipe with thermal insulation and providing aluminium cladding as per standards.

od48249/2023_2024 : Street Light poles&lt;br&gt;Supply, fixing, testing and commissioning of surface mounting, decorative street light pole of 8meter height with 1.5m overhang single arm bracket ( 50mm OD ) suitable for mounting 1 no street light fixture. The hot dip GI pole shall be provided with foundation base plate and the bracket assembly shall be secured on to the pol top with 1 annular rings with allen grub screws. The swagedpol with bracket built in cylindrical GI control box of some material with servicedoor coatd with poxyzinc phosphate primer and finished with polyurethanebased paint. The control gear box is prewired withDP MCB, FP connectors for easy loop-in-loop outsuitable for 3 phase 4 wire AC supply. The pole shall have provision for connecting the earth wires includes the supply drawing and termination of 3Cx2.5Sqmm Flexible Cu wire from control box to the light fixture and all other necessary accessories including civil foundation for Pole as required to complete all

od48250/2023_2024 : Street Light poles&lt;br&gt;Supply, fixing, testing and commissioning of surface mounting, decorative street light pole of 8 meter height with 1.5m overhang double arm bracket (50mm OD) suitable for mounting 2 nos street light fixtures. The hot dip GI pole shall be provided with foundation base plate and the bracket assembly shall be secured on to the pol top with 2 annular rings with allen grub scrws. The swagedpol with bracket built in cylindrical GI control box of some material with service door coatd with poxyzinc phosphate primer and finished with polyurethanebased paint. The control gear box is prewired withDP MCB, FP connectors for easy loop-in-loop out suitable for 3 phase 4 wire AC supply. The pole shall have provision for connecting the earth wires includes the supply drawing and termination of 3Cx2.5Sqmm Flexible Cu wire from control box to the light fixture and all other necessary accessories including civil foundation for Pole as required to complete accessories

od48251/2023_2024 : Supply, fixing, testing and commissioning of LED Street Lighting luminaires of IP 66 protected, IK08, with inbuilt protection of 6kV and external surge protection of 10kV, pressure die cast aluminium housing body with optimal heat sink, with system wattage less than 70W with minimum lumen output 10150 lumens having rated life of L70 @ 50000 hours &amp; system efficiency greater than145 lumens/watt. The light fitting shall be with all required accessories suitable for mounting in (48-60)mm OD pole arm. Weight of luminaire shall not be more than 10kg per fitting. The luminaire should meet all the technical specifications as mentioned. The street light luminaire shall be wired in the existing street light pole, complete with all accessories including lift &amp; lead the fittings, connection with 3Cx2.5Sqmm FRLS PVC insulated copper conductor cable and earthing etc. as required (make LT adornis or equivalent approved make)

od48255/2023_2024 : 2.5 sqmm 6 core PVC/ XLPE insulated armoured control cables with copper conductors for working voltages up to and including 1100 V conforming to IS 1554 part I 1988 for PVC and IS 7098 Part I for XLPE

od48257/2023_2024 : Supply of 8W LED up light 2700L 36 degree beam angle Al housing 50000 burning hrs IP 66

od48258/2023_2024 : 8 way (8 + 24) double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

od48259/2023_2024 : Providing coil/spring earthing using 2 runs of 8 SWG, Cu wire for street light pole etc. Cu wire buried to a minimum depth of 1.5m, with excavation, refilling and connecting Cu wire to pole using bolt and nut complete including all accessories required.(For bollards, post tops, street lighting poles etc)

od48260/2023_2024 : Supply, installation, testing and commissioning of 1no 30kVA UPS , 3 phase in and 3 phase out with surge protection system with 20 min back up battery at @ 30 kVA Load Minumum, 31200 VAH SMF VRLA battery required, APFC PWMIGBT Double conversion online VFI-SS-111 (Performance comply to IEC 62040-3) Technology.Input pf 0.99, Input THDi less than 5%,It shall be 100% generator compatible, with Efficiency greater than 92 % and output power factor unity (30kVA = 30 kW), Eco mode Efficiency 98% and including all accessories etc as required. The acoustic noise at 1m of the system should be less than 65dB.The system shall comply IEC 620401,2 and ISO 14025 (PEP) certificates. The system shall be true online double - conversion DSP based UPS system and also UPS shall be with automatic &amp; manual bypass switchBattery -65AH - 40nos

od48261/2023_2024 : Supply of 36/40W, 4000 lumen LED IP 66 street light fitting with aluminium housing mounted on a suitable GI pipe at one end including GI clamp , stove enameled CRCA sheet steel reflector cover, acrylic cover complete with THD less than10%, distribution complete with THD less than10%, PF greater than 0.98, RoHS compliant, duley wired up for use on 230V AC supply

od108852/2023_2024 : Supply and installation of FRP Earth Electrode Inspection Chamber minimum dimenssion has to be 290x290x190mm. Minimum Weight Bearing Capacity has to be 60KN. EC 290 or Equivalent

od108853/2023_2024 : Providing Earth Enhancing Mineral Compund (5kg) for improving earth soil conductivity. It should be pollution free and hazardous substances and chemically inert. Resistivity of the compound has to less than or equal to 0.2 ohm meter. PRO SAN 5 or Equivalent

od108854/2023_2024 : Providing Earth Enhancing Mineral Compund (12.5kg) for improving earth soil conductivity. It should be pollution free and hazardous substances and chemically inert. Resistivity of the compound has to less than or equal to 0.2 ohm meter. PRO SAN 12.5 or Equivalent

od108855/2023_2024 : Providing and fixing of Impact Point for easy insertion of earth rod to soil. IP or Equivalent

od108856/2023_2024 : Providing and fixing of 1m earth rod (with 20mm diameter and copper bonding thickness of minimum 250 microns) with with bore and peg arrangement CBR 2003 or Equivalent

od108857/2023_2024 : Providing and fixing of 1m earth rod (with 20mm diameter and copper bonding thickness of minimum 250 microns) with exothermically welded clamp on the top as per NBC 2016. CBR 2003 with Clamp or Equivalent

od108858/2023_2024 : Supply and installation of petrolatum- coated chemical fibre fabric having 1.1mm thick and width 50mm for underground joints. CT 5 or Equivalent

od108859/2023_2024 : Supply and Installation of Exothermic Weld Joints for 10mm round copper bonded steel conductor. C90 or Equivalent

od108860/2023_2024 : Providing and laying copper coated steel solid round conductor 10mm diameter with copper coating thickness of 100microns for laying conductor after test link and for ring earthing at a depth of 0.5 meters from ground level. Needs to be routed inside heavy duty 20mm PVC pipe after test link @ a height of 2.5 meters from ground level. SRC 10-CU or Equivalent

od108861/2023_2024 : DIN Rail Surge Protection Device (4+0) Class B+C/ Type 1+2 with Total Impulse current-10 KA (10/350&micro; sec) &amp; Total Max Discharge current 200kA (8/20 micro sec), Voltage protection level less than1.5 kV .The Surge Protection Devices should have TOV safefail for 120 Min : 442 V. Health Satus Indication in all the catridges.Total Response Time less than 25 nano seconds. Protec T2 (4+0) or Equivalent

od108862/2023_2024 : DIN Rail Surge Protection Device (4+0) Class B&amp;C/ Type 1&amp;2 with Total Impulse current-50 KA (10/350 micro sec) &amp; Total Max Discharge current 200kA (8/20 micro sec), Voltage protection level less than1.5 kV .The Surge Protection Devices should have TOV safefail for 120 Min : 442 V. Health Status Indication in all catridges.Total Response time less than 5 nano seconds. Protec T1 (4+0) or Equivalent

od108863/2023_2024 : Providing and fixing of Outdoor Glass Fibre Reinforced Polycarbonate Enclosure having minimum inner dimension of 75mm x 75 mm x 50 mm. Abox I 40 or Equivalent

od108864/2023_2024 : Providing and fixing of Stainless Steel SS 304 Test Joint. The 8mm &amp; 10mm Conductor has to be straightly connected to avoid risk of flash over and needs to have disconnection facility to measure values during testing. Minimum 4 screw/bolt joints required for strong bonding. TJRR or Equivalent

od108865/2023_2024 : Providing and fixing of Aluminium Alloy Ferrule Straight Connector for Expansion Piece joints and other straight joints to avoid bimetallic corossion. Crimping has to be done minimum in 4 points for strong bonding. CJ 8 or Equivalent

od108866/2023_2024 : Providing &amp; fixing of Terrace conductor (8mm solid aluminium alloy round conductor) made up of Semi-hard (E-AlMgSiO5). SRC 8-AL or Equivalent

od121481/2023_2024 : Supply and Installation of 40A 30mA FP high immunity RCCB

od122052/2023_2024 : Supply and laying the following sizes of Cu strips laid in trench/wall pulling through pipes/tray as required&lt;br&gt;32x3 Cu Strip tinned at the point of contact

od122309/2023_2024 : Supply, laying and fixing of earthing conductor of Cu Strip on trench/Wall pulling through pipes/trays as required&lt;br&gt;32x6 Cu Strips tinned at the point of contact

od150386/2023_2024 : Consultancy fees for KSECBC compliance

Electrical 2

1.10.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.11 : Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

1.14.1 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.14.2 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.17.3 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

1.17.12 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.17.21 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm

1.19 : Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

1.24.1 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.2 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.2 way 5/6 amps switch

1.24.3 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.24.7 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet

1.24.8 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Bell push

1.25 : Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

1.26 : Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.3 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.4 Module (125mmX75mm)

1.27.4 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

1.27.5 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)

1.28.1 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.1 or 2 Module

1.28.2 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.3 Module

1.28.3 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.4 Module

1.28.4 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.6 Module

1.28.5 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.8 Module

1.31 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

1.33 : Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

1.34 : Supplying and fixing brass batten/ angle holder including connection etc. as required.

1.35 : Erection of wall bracket / ceiling fittings of all sizes and shapes containing upto two GLS lamps per fitting, complete with all accessories including connection etc. as required.

1.38 : Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

1.39 : Providing and fixing plain 16/0.20mm (0.50sqmm) twin flat flexible, FRLS PVC insulated, copper cable, in PVC sleeve of suitable size on the floor / wall, or side of the table / door etc. as required.

1.40 : Providing and fixing plain 16/0.20 mm (0.50 sqmm) twin circular flexible FRLS PVC insulated, PVC sheathes copper cable direct on the wall with PVC clips etc as required.

1.41 : Installation, testing and commissioning of pre - wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

1.44 : Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

1.50.1 : Installation of exhaust fan in the existing opening, including making good the damage connection testing, commissioning etc. as required.Upto 450 mm sweep

1.51 : Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes

1.55.1 : Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group A

1.57 : Supplying & fixing suitable size Gl box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

2.3.2 : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator8 way, Double door

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.4 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

2.11 : Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

2.13.2 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.13.3 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.100 amps

2.18 : Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth,metal enclosed plug top along with 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

2.19 : Supplying and fixing 20 amps 415volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top along with 20 amps "C" curve, TPMCB, in sheet enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

2.21 : Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

2.22 : Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

2.25 : Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for tripple pole and neutral, sheet steel, Vertical MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.

4.1.2 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.150 mm width X 50 mm depth X 1.6 mm thickness

4.1.4 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.300 mm width X 50 mm depth X 1.6 mm thickness

4.1.6 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.450 mm width X50 mm depth X 2.0 mm thickness

4.1.11 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.600 mm width X 62.5 mm depth X 2.0 mm thickness

7.6.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required.Upto 35 sq. mm

7.6.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required.Above 35 sq. mm and upto 95 sq. mm

7.6.3 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required.Above 95 sq. mm and upto 185 sq. mm

7.7.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.8.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.8.2 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

7.8.3 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

8.3.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 120 sq. mm and upto 400 sq. mm

8.4.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required.Above 120 sq. mm and upto 400 sq. mm

9.1.21 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 35 sq. mm (32mm)

9.1.22 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 50 sq. mm (35mm)

9.1.23 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.24 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 95 sq. mm (45mm)

9.1.26 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 150 sq. mm (50mm)

9.1.27 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm)

9.1.32 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.33 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

9.1.34 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm)

7.1.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Upto 35 sq. mm

7.1.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 35 sq. mm and upto 95 sq. mm

7.1.3 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 95 sq. mm and upto 185 sq. mm

2.13.1 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

14.16.1 : Supplying and laying of following size DWC HOPE pipe lSI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 em below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required.63 mm dia (OD-63 mm & ID-51 mm nominal)

2.4.1 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)4 way (4 + 12), Double door

2.4.2 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way (4 + 18), Double door

2.4.3 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way (4 + 24), Double door

2.5.2 : Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)8 way (4 + 24), Double door

4.1.7 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.600 mm width X 50 mm depth X 2.0 mm thickness

4.1.3 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.225 mm width X 50 mm depth X 1.6 mm thickness

Solar Panel

od48143/2023_2024 : Supply, installation testing and commissioning of 30kWp on grid monoperc half cut Solar Panel system including Grid Tie Inverter having suitable capacity, mono Solar Panels, Mounting structure, cables, Communication Device, DC Surge Protection Device, AC Surge Protection Device, Including Inspectorate approvals,&lt;br&gt; Panel Erection, DC Wiring and Project commissioning

od48145/2023_2024 : Supply Installation testing and commissioning of Passenger Elevator of 13 passenger capacity, simplex operation, 60MPM, Machine Room less, Openings at basement, Ground, 1st, 2nd and Terrace Floor, HOIST WAY SIZE REQUIRED PER ELEVATOR is 2000 MM (W) X 2400 MM (D), CLEAR CABIN INTERNAL SIZE is 1100 MM (W) X 2000 MM (D) X 2300 MM (H) including all accessories required&lt;br&gt;

Pumps

od48147/2023_2024 : Supply &amp; fixing, testing and commissioning of SS centrifugal Waste water Transfer Pump (sewage pump), for pumping waste water/ Kitchen waste/ sewage waste from collection pit to Sewage treatment plant, with including solenoid valves, level switches, control wires etc. (1Working +1 standby pump) with suitable HP MAKE :Lubi. basement floor collection pit pumping line

od48151/2023_2024 : Providing &amp; laying of 4 pair 1.5 sq mm cable as control cable of liquid water level controller through a ISI Heavy duty 20mm conduit

od48153/2023_2024 : Providing &amp; Fixing, testing and commissioning of Automatic Three phase water level controllers with level sensors for submersible pump shall have the following features: a)Switch off the motor when the water level in tank reaches a preset level below the over flow pipe; b)Switch ON the motor if the water level in tank goes down below a preset value near. c)Switch off the motor in the event of dry running; d) Manual bypass mod

ELV Estimate

od115838/2023_2024 : CCTV SYSTEM&lt;br&gt;Supply, Installation, testing and commissioning of 2.8 mm fixed lens, 2MP, IR Dome camera 1.0 lux, 120 db WDR POE and vandal proof with all connectors and necessary accessories for mounting in True/false ceiling

od115841/2023_2024 : Supply, Installation,testing and commissioning of Varifocal Dome Camera with 2 MP 0lx, built-in IR LED,120DB WDR , 2.8-12 mm POE, Vandal proof with all connectors and necessary accessories for mounting on true ceiling

od115843/2023_2024 : Supply, Installation,testing and commissioning of Indoor Varifocal Bullet Camera with 2 MP , built-in IR LED, , 2.8-10 mm POE , IP 66 with all connectors and necessary accessories for mounting in false ceiling/True Ceiling

od115846/2023_2024 : Network Video Recorder with Storage Server: Supply, installation, testing and commissioning of 32 Channel Network Video Recorder with Raid 5 Supports 32 channels-4SATA, 720p resolution video recording at real time, NVR ONVIF , Recording resolution of Max 12 MP, Minimum of 200Mbps of recording, should support dual video output, H.265,H.264, MJPEG Compression.video playback / relay at real time.

od115850/2023_2024 : Supply, Installation, testing and commissioning of Outdoor Varifocal Bullet Camera with 2 MP , built-in IR LED, 2.8-10 mm POE , IP 67 with all connectors and necessary accessories for mounting in Pole/Exterior wall

od115852/2023_2024 : Supply, installation, testing and commissioning of HDD for cameras recording at 720p @ 20fps for 30 days 24 hours - 6 TB

od115856/2023_2024 : Supply, installation, testing and commissioning of workstation with Intel I7 or above, 8 GB ram and 2 TB HDD. Same system will be used for Access control

od115858/2023_2024 : Supply, Installation, Testing and Commissioning of LED Monitor 40

od115861/2023_2024 : PA SYSTEM&lt;br&gt;Supply, installation, testing and commissioning of 6 Watt recessed Type Speakers

od115864/2023_2024 : Supply &amp; Installation of 15 W Horn speaker for PA system

od115867/2023_2024 : Supplying, installing, testing and commissioning Audio booster Amplifier 240 Watts RMS, complete with Speaker wires and RGB connectors for Integrated Music &amp; PA system

od115870/2023_2024 : Supplying, installing, testing and commissioning of Digtal PA Master Processor with fully Digital Audio system for Public Address and Evacuation consisting of audio digital signal processing (DSP), a matrix, digital message player, 40min Audio message memory, Fireman microphone on Front side for Emergency paging, Red color EVAC button on Front, amplifiers monitoring with switchover to backup amplifier, loudspeaker lines monitoring(mandatory), LCD display for fault checking, Onboard volume control for each zone, Integrate with PBAX System for announcement. &lt;br&gt;Note: Master processor should incorporate minimum of 2 zones.

od115874/2023_2024 : Supply &amp; Installation of 2 zone call station with mic

od115877/2023_2024 : Supply, installation, testing &amp; commissioning of Audio player with DVD/USB /FM/WiFi connectivity option for playing music

od115879/2023_2024 : Supply &amp; Wiring of Speaker system using 2core of 1.0sqmm PVC insulated copper FRLS Armoured cable

1.53.1 : Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable

od115883/2023_2024 : Supply, fixing, testing and commissioning of CAT6 Information Outlets for Data with face plate, Keystone Jack, Back box etc. as required for complete installation.

od115886/2023_2024 : Supply, fixing, testing and commissioning of Keystone jack for data outlets (for cameras) as required installation

od115890/2023_2024 : Supply, fixing, testing and commissioning Cable Manager

od115893/2023_2024 : Supply, fixing, testing and commissioning of CAT6 Patch Cable - 1 Meter etc. of approved make as required for complete installation

od115896/2023_2024 : Supply, fixing, testing and commissioning of CAT6 Patch Cable - 2 Meter etc. of approved make as required for complete installation

od115899/2023_2024 : Supply, installation, testing and commissioning of 16 Port Unmanaged POE Switch. 16 x 10/100/1000BASE-T ports2 x Gigabit SFP portsAdvanced L2 switching and security featuresL2+ Static RoutingOptional &ldquo;standard mode&rdquo; or &ldquo;surveillance mode&rdquo; management user interfaceUp to 300 m Long Range PoE Transmission,

od115901/2023_2024 : Supply, Installation, Testing &amp; Commissioning of 12port 10/100/1000 Base-T network Switch with 1G copper uplink 12x 1G copper ports and all related termination accessories as per vendor specific System requirement

od115906/2023_2024 : Supply, Installation, Testing &amp; Commissioning of 16U Depth Floor/Wall Mount Networking Rack with Front Perforated Convex Door, Rear Perforated SPLIT Doors, Side Openable Panels, Castors, Heavy Duty Shelf - 1 No, Horizontal Cable M anager - 2 Nos, Cantilever Shelf - 1 No, Vertical PDU 12X5Amps - 1 No, Fan Housing Unit with 4 Fans - 1 Set, M ounting Hardware Screwsand all other required accessories

od115908/2023_2024 : Supply, Installation, Testing &amp; Commissioning of 24U Floor/Wall Mount Networking Rack with Front Perforated Convex Door, Rear Perforated SPLIT Doors, Side Openable Panels, Castors, Heavy Duty Shelf - 1 No, Horizontal Cable M anager - 2 Nos, Cantilever Shelf - 1 No, Vertical PDU 12X5Amps - 1 No, Fan Housing Unit with 4 Fans - 1 Set, M ounting Hardware Screwsand all other required accessories

od115910/2023_2024 : Supply, installation, testing and commissioning of 8 Channel Network Video Recorder with Raid 5 Supports 8 channels 720p resolution video recording at real time, NVR ONVIF , Recording resolution of Max 12 MP, Minimum of 200Mbps of recording, should support dual video output, H.265,H.264, MJPEG Compression.video playback / relay at real time.

od115913/2023_2024 : 12 Port Cat6 Patch Panel with all accessories loaded

od115916/2023_2024 : 24 Port Cat6 Patch Panel with all accessories loaded

od115919/2023_2024 : Supply, Installation, Testing &amp; Commissioning of 24 port 10/100/1000 Base-T network Switch with 1G copper uplink 24x 1G ports and all related termination accessories as per vendor specific System requirement. 24 Port Switch

od115922/2023_2024 : Switches&lt;br&gt;Supply, Installation, Testing &amp; Commissioning of 24 Port Unmanaged POE Switch. 24 x 10/100/1000BASE-T ports2 x Gigabit SFP portsAdvanced L2 switching and security featuresL2+ Static RoutingOptional &ldquo;standard mode&rdquo; or &ldquo;surveillance mode&rdquo; management user interfaceUp to 300 m Long Range PoE Transmission,

od115923/2023_2024 : EPBAX &quot;Supply, Installation, Testing and Commissioning of PBX with 70 Analog extensions expandable up to 150 ports (Extensions/Trunks) , single line digital phone with 5 navigation keys 5 Digital IP Extensions and 5 SIP License with maximum of 20 concurrent calls Network Interface: 1&times;10/100M LAN port 1 PRI interface, RAM: DDR3 1GB, Power Consumption: 12V/0.8A, 9.6W Maximum, Failover Function (optional), Web Interface, Call Dashboard, DISA, IVR, Call Hunt, 19&apos;&apos; rack mountable etc. Features: Room monitoring from outside Warning Message during night mode Remote Inspection, with autoemergency call Sensor Connectivity with auto-emergency call and warning message sending Built-In Auto Answer (Standby mode) during night mode TDM/IP Coverage ISDN Compatibility Voice Mail Integration Paging Announcement Programmable Function Keys Programmable Function Keys&rdquo;.

od115926/2023_2024 : Supply, installation, testing and commissioning of single line digital phone with 5 navigation keys with necessary connection as required for complete installation

od115927/2023_2024 : Supply, installation, testing and commissioning of Basic user phone with necessary connection as required for complete installation

od115929/2023_2024 : Supply and fixing 100 pair 0.51 mm dia telephone tag block &quot;Krone or equivalent make&quot; with termination box

od115931/2023_2024 : Supply and fixing Multi Wan Gigabit VPN Router GWN 7001 features built in firewall security.It includes 6Gigabit Ethernet ports connecting upto 150 Data Point

od115934/2023_2024 : Supply and fixing 30 pair 0.51 mm dia telephone tag block &quot;Krone or equivalent make&quot; with termination box

od115936/2023_2024 : Supply and fixing 20 pair 0.51 mm dia telephone tag block &quot;Krone or equivalent make&quot; with termination box

od115937/2023_2024 : Supply and fixing 10 pair 0.51 mm dia telephone tag block &quot;Krone or equivalent make&quot; with termination box

od115939/2023_2024 : Supply and laying 100 pair telephone cable

od115942/2023_2024 : Supply and laying 50 pair telephone cable

od115943/2023_2024 : Supply and laying 30 pair telephone cable

od115945/2023_2024 : Supply and laying 20 pair telephone cable

od115947/2023_2024 : Supply and laying 10 pair telephone cable

od115949/2023_2024 : Supply and installation of modular type telephone socket outlet mounted in separate PVC box including supply of modular PVC mounting box, telephone socket covering with modular cove plate giving connection etc as required.

1.18.2 : Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor,unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair

od115955/2023_2024 : Supply and fixing of 32 x 12.5 mm PVC Cable Management System with base and lid along with all accessories like external angle, internal angle, flat angle, end cap etc conforming to IEC 61084/ BS 476 &amp; 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required and instructed by engineer in charge/consultant, including all accessories as required for complete installation. (OBO Betterman make or equivalent)

od115956/2023_2024 : Supply and fixing of Perforated Cable tray with horizontal &amp; vertical bends, reducers, Tee&apos;s, cross over, suitable supports and brackets and other accessories as required confirming to IEC-61537. The Tray shall be galvanized for corrosion protection confirming to DIN EN 10346 / ISO 1461 .The trays should be tested for a max. safe working load of 150 Kgs with a span distance of 1.5 meters and the deflection should be within the limits as per standard. The safety factor shall be 1.7 times of the safe working load. The perforated tray shall be supplied with the standard length of 3 Mtr . (OBO Betterman make/Equivalent)

Fire Protection Systems

od115837/2023_2024 : Supply, Installation, Testing and Commissioning of Electrical Driven Main Pump suitable for automatic operations and consisting of the following:-a) End suction type fire pump capable for delivery of 1620 Ltrs/Min,head of 70 M rated 2900 RPM with with SS shaft, CI casing, &amp; CI impeller. b) Squirrel cage, TEFC induction Motor suitable for 415 volts &plusmn; 10%, 3 Phase 50 Hz, AC supply, of suitable capacity for the above pump, rated for 50 HPc) Common bedplate of requisite strength fabricated out of MS channel type.d) The pump should ensure a pressure of 3.5 kg/cm2 at the farthest sprinkler/hydrant point.e) The rate shall include base plate common to pump and motors, foundation bolts, coupling, coupling guards and connecting cables from fire panel to the motor.

od115839/2023_2024 : Jockey PumpSupply, installation, testing and commissioning of Electric Driven Jockey pump for automatic pressurization of wet riser system in cases of minor leakages consisting of the following:a) Centrifugal End Suction back pullout type Centrifugal fire pump CI impeller, running at 3000 RPM capable of delivering 180 LPM against a head of 70 Mtrs.b) Squirrel cage TEFC induction motor suitable for 415V, 3 phase, 50Hz AC supply of suitable 7.5 HP conforming to IP-55 protection &amp; class &lsquo;F&rsquo; insulation for the above pump running at 3000 RPM.c) Common bed plate of requisite strength manufactured out of MS channel type.d) The rate shall include base plate common to pump and motors, foundation bolts antivibration pad, Coupling,coupling guards and connecting cables from fire panel to the motor.

od115842/2023_2024 : Diesel PumpSupplying, Installing, Testing &amp; Commissioning of Diesel Engine Driven Fire Pump of approved make suitable for automatic operation consisting of following, complete as required and as per specifications;a) Horizontal End Suction Centrifugal Fire pump capable for delivery of 1620 Ltrs/Min at 70 MWC (Meter of Water Column) rated for suitable 52 HP at 2920 RPM with with SS shaft, cast iron casing &amp; cast iron impeller to ensure minimum pressure of 3.50 kg per square cm.b) Diesel engine suitable for the above pump complete with stanadard accessories and suitable water cooling systemc) Suitable mechanical seal with mounting arrangement.d) Tyre type Coupling and coupling guard for direct coupling of engine &amp; pump. The pump shall be supplied with suitable battery and charger for atleast three cranking,and the fuel tank supplied shall be suitable for minimum 8 hours running &amp; exhaust pipe of required length to discharge outside building with mineral wool insulation.e)The rate shall include RCC foundation for pump, base plate common to pump and engine, foundation bolts antivibration pad, Coupling,coupling guards and connecting cables from fire panel to the motor.

od115848/2023_2024 : Exhaust pipe - SITC of exhaust pipe for diesel engine pump

od115851/2023_2024 : Supply, Installation, Testing and Commissioning of Electrically operated Terrace Pump of 900 LPM capacity 24 MWC, high efficiency volute type with cast iron casing, cast iron impeller, pump coupled with a squirrel cage induction motor SPDP type with a supply condition of 415 V 50 Hz foot mounted type for Appx. 5HP at 2900 RPM 3 kg including base plate coupling guard and all other necessary accessories.

od115855/2023_2024 : AIR RELEASE VALVE&lt;br&gt;Supply, Installation, Testing and Commissioning of brass body Air Release Valve 25 mm dia type of approved make

od115859/2023_2024 : PRESSURE GAUGES&lt;br&gt;Supplying, installing, testing and commissioning of Pressure gauges for the respective floors near to the flow switches with Ball valves, siphon, Fittings like unions / colors / reducers etc. Glycerine filled pressure gauges to use on pump discharge lines. with 0 to 200PSI, 25 mm dia. Dial should be 150 mm dia.

od115862/2023_2024 : HOSE REEL DRUM&lt;br&gt;Supply, Installation, Testing and Commissioning of swinging type Hose reel drum made of 16 gauge MS sheet to keep 19 mm dia 30 Mtrs long black coloured PVC lined heavy duty rubber braided hose pipe with PVC nozzle on one end and all other necessary fixing materials. It should be ISI mark approved

od115863/2023_2024 : FIRE HOSE &lt;br&gt;Supply, installation, testing and commissioning of 63mm dia Non percolating flexible and light weight synthetic fire fighting delivery hose with textile reinforcement, resistant to chemicals, acids, alkalis, abrasions, heat and ozone having 36Kg/cm 2 burst pressure including SS make and instantaneous type ISI marked coupling approved by fire authority, machine would with copper wire complete in all respects. Single length (15 m)

od115866/2023_2024 : HOSE CABINET&lt;br&gt;Supply and Fixing of weather proof MS Hose cabinet of size made of 16 gauge MS Sheet with locking arrangements, suitable to accommodate One/Two length of hose pipe along with one pair of male and female coupling and one branch pipe. The cabinet shall be painted to scarlet red colour out side and off-white inside. The words &quot;FIRE HOSE&quot; to be painted on the box. The fire hose cabinet shall be approved by architect/PMC before procuring it.&lt;br&gt;Single door (600 x 400 x 250mm)

od115869/2023_2024 : HYDRANT VALVE&lt;br&gt;Supply, Installation, Testing and Commissioning of SS (304) Hydrant Valve 80mm inlet with single outlet fitted with 63mm instantaneous female coupling on the outlet complete with flange as required blank cap and chain. Conforming to IS:5290 and of ISI mark.

od115872/2023_2024 : BRANCH PIPE &lt;br&gt;Supply and Installation of SS (304) short branch pipe conforming to IS: 903 of ISI mark with 63 mm dia instantaneous coupling on one end and threading 26mm nozzle.)

od115876/2023_2024 : PRESSURE SWITCHES&lt;br&gt;Supplying, installing ,testing and commissioning of Pressure switches of suitable range for pump sets with Ball valves, Fittings like unions / colors / reducers etc.

od115878/2023_2024 : BALL VALVE &lt;br&gt;Supply, Installation, Testing &amp; Commissioning of forged Brass body stainless steel lever operated Ball valve (PN 25) of approved make with necessary weldable fittings in position as per drawings. 25 mm dia

od115881/2023_2024 : 20 mm dia

od115884/2023_2024 : Y- STRAINER&lt;br&gt;Supplying, installing and commissioning flanged C.I &quot;Y&quot; type Strainer (PN.16) with SS mesh, suitable flanges, nuts, bolts, gaskets etc. complete. 200 mm dia

od115888/2023_2024 : Supply,Installation, Testing and Commissioning CI Butterfly Valves (PN 10) slim seal standared lever operated type confirming to BS: 5155 with DI shaft &amp; disc, flanges, nuts, bolts etc. complete.200mm dia

od115889/2023_2024 : 65 mm dia

od115894/2023_2024 : 80 mm dia

od115897/2023_2024 : 100 mm dia

od115898/2023_2024 : NON RETURN VALVE Supply,Installation, Testing and Commissioning of Wafer Swing type Check Valve (IS:13095) of following sizes having CI body and moving parts, with nuts bolts, gaskets, 3mm thick rubber insertions etc &amp; tested to 1.5 times working pressure.100mm dia

od115902/2023_2024 : 80 mm dia

od115905/2023_2024 : TANK FILLING INLET&lt;br&gt;Supply, installation, testing and commissioning of 2 Way tank filling Inlet connection with 2 nos of 63 mm dia. built - in Gun metal Nonreturn valves instantaneous coupling type arranged on 150 mm dia etc.pipe manifold shall be connected to wet riser main.

od115909/2023_2024 : FBC - Supply, installation, testing and commissioning of 2 Way Fire Brigade Inlet connection with 2 nos of 63 mm dia. built - in Gun metal Non- return valves instantaneous coupling type arranged on 150 mm dia etc.pipe manifold shall be connected to wet riser main

od115911/2023_2024 : ABOVE GROUND PIPING&lt;br&gt;Supplying, fixing, testing and commissioning of MS &lsquo;C&rsquo; class pipes of following sizes along with necessary clamps, vibration isolators and fittings such as bends, tees etc. but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. 25 mm dia

od115914/2023_2024 : 200 mm dia

od115915/2023_2024 : 150 mm dia

od115917/2023_2024 : 100 mm dia

od115920/2023_2024 : 80 mm dia

od115921/2023_2024 : 65 mm dia

od115924/2023_2024 : 50 mm dia

od115925/2023_2024 : 40 mm dia

od115928/2023_2024 : 32 mm dia

od115930/2023_2024 : UNDER GROUND PIPING&lt;br&gt;Supplying, fixing, testing and commissioning of MS &lsquo;C&rsquo; class pipes of following sizes of along with necessary clamps, vibration isolators and fittings such as bends, tees etc. but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. 200 mm dia

od115932/2023_2024 : 100 mm dia

od115933/2023_2024 : 150 mm dia

od115935/2023_2024 : SPRINKLER&lt;br&gt;Sprinkler Bulbs: Supply, Installation, Testing and Commissioning of 15mm dia nominal bore quartzoid bulb type sprinklers with temperature rating of 68 / 93 deg C of K-80 factor, conventional type, shall also include suspending arrangement with ceiling, wall arrangement with ceiling, wall beam clamps, fasteners etc. Pendant type of 68 deg C

od115938/2023_2024 : FLEXIBLE PIPE&lt;br&gt;Supplying, installing, testing and commissioning of Stainless Steel Unbraided Flexible Pipe (hose) for dropping sprinklers below false ceiling, pipe shall be 14 bar pressure rating and 1000/1500/1800 mm long 25 mm dia with union / reducer collar, clamps etc. as required. It shall have UL Listed. 1000 mm

od115944/2023_2024 : ROSETTE PLATES&lt;br&gt;Supply, Installation, Testing and Commissioning of approved type Rosette plates (one-piece) for Sprinklers below false ceiling area. The Rosette shall be chrome plated &amp; shall be as approved by architects / consultants.

od115946/2023_2024 : FIRE EXTINGUISHERS&lt;br&gt;Supply and fixing of 4Kg ABC Dry Powder (Stored Pressure) Type Fire Extinguisher. pressurized with dry nitrogen gas at 15 bar. Design, construction and testing as per IS 15683, external epoxy powder coating with PO Red Shade, Supplied with standard accessories.

od115948/2023_2024 : FIRE ALARM CABLE&lt;br&gt;Supply, laying, testing and commissioning of Fire Alarm Cable - PVC insulated fire retardant copper flexible wire 1 sq.mm with ISI mark.

od115950/2023_2024 : HEAT DETECTORS&lt;br&gt;Supply, Installation, Testing and Commissioning of Heat Detectors with all accessories like base etc to be installed under or above false ceiling, UL Approved

od115951/2023_2024 : SMOKE DETECTORS&lt;br&gt;Supply, Installation, Testing and commissioning of Smoke detectors with all accessories like base etc to be installed under or above false ceiling , UL Approved

od115952/2023_2024 : HOOTER&lt;br&gt;Supply, Installation, Testing and commissioning of Audio alarm hooter (sounder) powder coated MS box or ABC type 24/12 Volt DC operated with necessary attachments.

od115953/2023_2024 : MANUAL CALL POINT&lt;br&gt;Supply, Installation, Testing and Commissioning of Manual Call Point resettable type powder coated or ABC type 24/12 Volt DC operated, and with necessary attachments.

od115954/2023_2024 : FIRE ALARM CONTROL PANEL&lt;br&gt;Supply, Installation, Testing and Commissioning of Fire alarm control panel with 8 Zone conventional type micro processor based control panel of MS cabinet powder coated audio and visual display with all necessary attachments &amp; battery.

od115957/2023_2024 : Supplying and installing in position self glowing &quot;FIRE ASSEMBLY POINT&quot; sign boards of size (150 X 300 mm) made of luminescent safely, rigid sheet in green colour, photo luminescent two foam sheet fixed on the wall. Samples has to approved by the Architect before procuring the same.

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

od115958/2023_2024 : Supplying and installing in position self glowing sign boards of sixe (150 X 400 mm) made of luminescent safely, rigid sheet in green colour, photo luminescent ACP sheet in protective glass with two hanging chains &amp; necessary supports to hang it on ceiling. Samples has to approved by the Architect before procuring the same of the following signs FIRE EXIT

od115959/2023_2024 : NO SMOKING

od115960/2023_2024 : FIRE DUCT

od115961/2023_2024 : EXIT

od115962/2023_2024 : STATUTORY APPROVAL&lt;br&gt;Preparation of drawings/ schemes/ documents and getting final approval/ sanction/ NOC from statutory departments viz. Fire Force Department, etc. as per rules and regulations (statutory fees if any will be borne by the owner).

od134797/2023_2024 : a) Supply, installation, testing and commissioning of Draw out connection 100 mm dia in CI Body Gun metal working parts.

od134798/2023_2024 : b)M.S class &apos;B&apos; (Medium class) 100mm dia

od134799/2023_2024 : c) Foot Valve(Ball type) 100 mm dia

od134800/2023_2024 : Draw out connection &lt;br&gt;d) Butterfly Valve 100 mm dia

od137007/2023_2024 : EVACUATION PLAN

od137008/2023_2024 : Supply, Installation of Fire Extinguisher Modular type Clean agent fire extinguisher ISI mark , 5 kg capacity with initial charger and installation brackets.

od137009/2023_2024 : Supply, Installation of Fire Extinguisher ABC Modular type fire extinguisher ISI mark , 5 kg capacity with initial charger and installation brackets.

od137010/2023_2024 : Supply and fixing of 4Kg ABC Dry Powder (Stored Pressure) Type Fire Extinguisher. pressurized with dry nitrogen gas at 15 bar. Design, construction and testing as per IS 15683, external epoxy powder coating with PO Red Shade, Supplied with standard accessories.

od137011/2023_2024 : PRESSURE SWITCHES&lt;br&gt;Supplying, installing ,testing and commissioning of Pressure switches of suitable range for pump sets with Ball valves, Fittings like unions / colors / reducers etc.

od137012/2023_2024 : M.S Structural support &lt;br&gt;Supply, Installation, Testing and Commissioning of MS. Structural support including , cutting welding with nut bolt &amp; anchor fastners.

HVAC Estimate

od115836/2023_2024 : Supply, installation, testing, and commissioning of VRV/VRF Outdoor Air Conditioning units of the following capacities. Combination of digital/ inverter hermetic scroll compressorssuitable for operation on R-410A refrigerant Gas, complete with high/low pressure cut-outs, oil pressure failure switch, fan motor, safety thermostat, over current relay, fusible plugs, fuses,cabling etc. andsuitableforoperationon 380V~415V~3Ph~50Hz A.C. supply, Oil separator suitable for the refrigerant piping, liquid and gas shut off valves and solenoid valves / modulation valve with fittings to interconnect the compressor,condenser and evaporator coils etc(Combination of 16HP &amp; 14HP)

od115840/2023_2024 : VRV / VRF Celiling Mounted Middle &amp; High Static Duct Indoor Units&lt;br&gt;Supply, installation, testing, and commissioning of following capacities VRV Indoor air conditioning units with all accessories, refrigerant, insulated motorised drain assembly etc. 8.0 TR Ceiling Mounted High Static Duct Type

od115844/2023_2024 : 1.6 TR Ceiling Mounted Middle Static Duct Type

od115847/2023_2024 : 2.6 TR Ceiling Mounted Middle Static Duct Type

od115849/2023_2024 : Copper distribution Joints&lt;br&gt;Supply, installing testing and commissioning of copper distribution Joints with insulation and proper supports

od115853/2023_2024 : COMMUNICATION CABLE&lt;br&gt;Supply and Installing of Communication cabling between indoor and outdoor units of Ductable split.

od115854/2023_2024 : Supply and Installing of Communication cabling between all indoor units and outdoor units of VRV

od115857/2023_2024 : ELECTRICAL POWER CABLE&lt;br&gt;Supply and Installing of Power cabling to Ductable split outdoor units using copper cable of following sizes and 12 SWG copper double earthing. 1.5 Sqmm x 5 Nos (VRF Indoor)

od115860/2023_2024 : 2.5 Sqmm x 2 Nos (VRF High static Indoor)

od115868/2023_2024 : REFRIGERANT PIPING&lt;br&gt;Supply and laying of Refrigerant Piping for above units including Copper Soft/Hard&lt;br&gt;pipes, fittings, supports, saddle, 9/10 mm thick Nitrile Rubber Insulation, PVC sleeves, Pressure Testing, Evacuation &amp; commissioning (Minor civil work like brick wall chasing/partition cutting to be done by a/c contractor &amp; markings for major civil work to be provided by a/c contractors)a)6.35 mm Dia Liquid Line

od115871/2023_2024 : b)9.52 mm Dia Liquid Line

od115873/2023_2024 : c)12.70 mm Dia Liquid Line

od115875/2023_2024 : d)15.88 mm Dia Liquid Line

od115880/2023_2024 : e)19.05 mm Dia Liquid Line

od115882/2023_2024 : f) 22.22 mm Dia Gas line

od115885/2023_2024 : g) 28.58 mm Dia Gas line

od115887/2023_2024 : h)34.93 mm Dia Gas line

od115891/2023_2024 : DRAIN PIPE&lt;br&gt;Supply and fixing in position of insulated PVC condensate drain water piping with necessary fittings like elbows, tees and reducers insulated with 6mm vidoflex / eqv. 32 mm dia

od115892/2023_2024 : DUCTING AND INSULATION WORKS&lt;br&gt;Supply, Fabrication, Leading to site and Installation of Galvanised Sheet Steel Rectangular Ducting complete with all fittings such as Reducers, Tee bends, takeoffs, Suspension, Hi-tech supporting arrangements for plenum, Ducts etc. complete as required for the air conditioning application GSS Ducting for Indoor Units 24G

od115895/2023_2024 : GSS Ducting for Indoor Units 22G

od115900/2023_2024 : CANVAS CONNECTIONS&lt;br&gt;Supply, fabrication, Installation and testing of flexible connections constructed flexible double canvas sleeve in accordance with approved shop drawings and as per the specifications for each Packaged &amp; Ductable units.

od115903/2023_2024 : THERMAL INSULATION&lt;br&gt;Supply, installation &amp; testing of Thermal Insulation of ducting using Closed Cell Elastomeric nitrile rubber having a density of 40-60 Kg/m3 and thickness of 9mm with Microban Certified antimicrobial protection

od115904/2023_2024 : Grill and Diffusers Supply, Installation, testing and balancing of grilles of Aluminium construction with powder coated finish Return air Grill with out damber

od115907/2023_2024 : ACOUSTIC INSULATION&lt;br&gt;Supply, installation &amp; testing of Acoustic Insulation of ducts using opencell processed nitrile rubber having a density of 140-180 Kg/m3 and thickness of 9 mm with Microban Certified antimicrobial protection

od115912/2023_2024 : Supply and Installing of Power cabling to Ductable split outdoor units using copper cable of following sizes and 12 SWG copper double earthing. 4 Sqmm x 3 Nos + 2.5 Sqmm x 1 No (8.5 TR)

od138344/2023_2024 : Supply, Fabrication, Leading to site and Installation of Flexible duct 6 inch complete with all fittings

od138345/2023_2024 : Testing and commisioning with charging of R-410A&lt;br&gt;Refrigerant Gas&lt;br&gt;

od138346/2023_2024 : 6000 cfm Inline fan

od138347/2023_2024 : 500 cfm Inline fan

od138348/2023_2024 : 600 cfm Inline fan

od138349/2023_2024 : VENTILATION&lt;br&gt;100 cfm Inline fan

od138350/2023_2024 : 4.6 TR Ceiling Mounted High Static Duct Type

od139987/2023_2024 : Disc valve

THE URALUNGAL LABOUR CONTRACT CO-OPERATIVE SOCIETY

Bidder Name

THE URALUNGAL LABOUR CONTRACT CO-OPERATIVE SOCIETY

Unique Builders and Developers