REPAIR/ PAINTING AND POLISHING OF WOODEN AND STEEL FURNITURE AT DEAL AND IRDE UNDER GE(I) RND DEHRADUN

Amount

Repair/ Recushioning of Sofa Set 5 Seats/3 Seats. FD-281,FD-373,FD/MAP-II/02

(a) Removing the existing u/s covers from detachable foam cushion and S&F new cover made out of superior quality tapestry cloth of approved quality (locally available), not less than Rs. 550/-per meter) duly stitched as per size of seat & one side be stitched with zip chain of approved quality complete all as specified & shown on drgs & approved by GE

(b) S&F foam cushion 100mm thick and 40density, size 22”x21”x4” duly covered with new tapestry cloth & duly stitched as per size of seat & one side be stitched with zip chain (of approved type/ design/colour) (not less than Rs. 550/- per mtr) of appropriate quality fixed as in repairs complete all as shown on draing, specified & directed by Engr-in-charge, as approved by GE.

(c) Removing the existing u/s front legs from Sofa set 04/05seater and S&F new front leg made out of Teak Wood duly finished & complete to match the original as shown on Drg as directed

(d) Removing the existing u/s Rear legs from Sofa set 04/05seater and S&F new Rear legs made out of Teak Wood duly finished & complete to match the original as shown on Drg as directed

(e) Removing the existing u/s Batterns from Sofa set 04/05seater and S&F new Battern made out of Teak Wood duly finished and complete to match the original as shown on Drg as directed

(f) Removing the existing u/s Long Rails from Sofa set 05seater and S&F new Long Rail made out of Teak Wood duly finished & complete to match the original as shown on Drg as directed

(g) Removing the existing u/s Hand Rest from Sofa set 05seater and S&F new Hand Rest made out of Teak Wood duly finished & complete to match the original as shown on Drg as directed

(h) Removing the existing u/s Shorl Rail from Sofa Single seater and S&F new Short Rail made out of Teak Wood duly finished & complete to match the original as shown on Drg as directed

(j) French Polishing to Sofa Set 05 Seater

(k) French Polishing to Sofa Set 03 Seater

REPAIR TO TABLE BED SIDE FD-210, FD-248, FD- 276

(a) Removing and S&F new top of table bed side made up of 18/19 mm thick pre- laminated MDF board of shade bavarian beech exterior grade of size 450x350mm.

(b) Removing of old unsv sides of table bed side and S&F new sides of table bed side made out of 18/19mm thick MDF board of shade bavarian beech exterior grade of size 450x300mm

(c) Removing of unserviceable ply wood back and S&F new back made out of 6mm thick commercial plywood of table bed side of required size

(d) Removing of unsr shelf/base of table bed side made out of 18/19mm MDF board exterior grade

(e) French Polishing to table bed side

REPAIR TO TABLE CENTRE: FD-29(M),FD-134(M),FD-152(M),FD-235,FD-274,FD-393

(a) Removing of old U/S existing top from table and S&F new top of size as per drg. Top shall be 18/19mm thick MDF board exterior grade as approved by GE conforming to IS-12823 Grade-I type-II duly shade shal be Bavarian Beech screwed. Edging all round the top shall be of 4mm teakwood

(b) Removing of old U/S leg and S&F new leg made out of Teak Wood as per drg complete to match the existing surfaces of the item

(c) Removing the existing u/s long rail from Table centre and S&F new long rail made out of Teak Wood duly finished & complete to match the original as shown on Drg as directed by Engr-in-charge

(d) Removing the existing u/s Short Rails from Table centre and S&F new short rails, made out of Teak Wood duly finished & complete to match the original as shown on Drg as directed

(e) Removing the existing u/s Stiffners from Table centre and S&F new Stiffners made out of Teak Wood duly finished & complete to match the original as shown on Drg as directed by Engr-in-charge

(f) French Polishing to Table Center

REPAIRS TO TABLE PEG: FD-25(M),FD-236,FD-266,FD-277,FD-384

(a) Removing of old U/S existing top from table and S&F new top of size as per drg. Top shall be 18/19 mm thick MDF board exterior grade as approved by GE conforming to IS-12823 Grade-I type-II duly shade shal be Bavarian Beech screwed. Edging all round the top shall be of 4mm teakwood.

(b) Removing of old U/S leg and S&F new leg made out of Teak Wood as per drg complete to match the existing surfaces of the item.

(c) Removing the existing u/s long rails from Table peg and S&F new long rails made out of Teak Wood duly finished & complete to match the original as shown on Drg as directed by Engr-in-charge

(d) Removing the existing u/s Short Rails from Table peg and S&F new short rail made out of Teak Wood duly finished complete to match the original as shown on Drg as directed by Engr-in-charge

(e) Removing the existing u/s Stiffners from Table peg and S&F new Stiffners made out of Teak Wood duly finished complete to match the original as shown on Drg as directed by Engr-in-charge

(f) French Polishing to Table peg

REPAIRS TO TEAPOY WOODEN/FD: FD-34(M),FD-232,FD-278,FD-382

(a) Removing of old U/S existing top from table and S&F new top of size as per drg. Top shall be 18/19mm thick MDF board exterior grade as approved by GE conforming to IS-12823 Grade-I type-II duly shade shal be Bavarian Beech screwed. Edging all round the top shall be of 4mm teakwood.

(b) Removing of old U/S leg and S&F new leg made out of Teak Wood as per drg complete to match the existing surfaces of the item.

(c) Removing the existing u/s long rail from Teapoy wooden and S&F new long rail made out of Teak Wood duly finished & complete to match the original as shown on Drg as directed

(d) Removing the existing u/s Short Rail from Teapoy wooden and S&F new short rail made out of Teak Wood duly finished complete to match the original as shown on Drg as directed

(e) Removing the existing u/s Stiffners from Teapoy wooden and S&F new Stiffners made out of Teak Wood duly finished & complete to match the original as shown on Drg & as directed

(f) French Polishing to Table peg

REPAIRS TO TABLE DRESSING LADIES FD-32 (M),FD-251,FD-378

(a) Removing of old U/s mirror from table dressing ladies and S&F new mirror of size 1220 x 365 x 5 mm thick, duly fixed with frame as per drg.

(b) Removing of old U/s plastic laminated sheet from the top of table and providing new plastic laminated sheet 1.00mm thick duly fixed with synthetic adhesive as per drg

(c) Removing of old U/s glass shutters and aluminium channels and providing new sliding glass shutters duly fixed with new aluminium channels as per drg.

(d) Removing of old U/s drawer with knobs and providing of new drawers of MDF board 18/19 mm thick for sides and 6 mm thick ply wood commercial ISI marked for bottom including chromium plated knobs as per drg.

(e) French Polishing to Table Dressing Ladies

REPAIRS TO TABLE DRESSING GENTS. FD-31(M),FD-230,FD-379

(a) Taking down u/s broken mirror and S&F new mirror 760x365x5mm thick, duly fixed with frame as per drg

(b) Removing of U/s laminated sheet from top of table and providing new plastic laminated sheet 1.00 mm thick of on top duly fixed with synthetic adhesive as per drg

(c) Removing of old U/s drawer & knobs and providing new drawer made out of Teak Wood 12mm thick MDF board for side and 06mm thick ply wood commercial for bottom including knobs CP as per drawing

(e) French Polishing to Table Dressing Gents

REPAIRS TO HAT STAND WITH MIRROR SMALL/LARGE FD-23(M),FD-206,FD-233,FD-361,FD-362

(a) Removing of old U/S ply wood of hat stand and S&F new ply wood 3.5mm thick one side Teak Face all as directed by Engineer-in-Charge and as per drg. 4mm thick teak wood edging shall be provided ISI marked

(b) Removing of old U/S pegs of hat stand and S&F new metal pegs (CP) all as directed by Engineer-in-Charge and as per drg.

(c) Removing of old u/s broken mirror of hat stand and S&F 04mm thick new mirror all as directed by Engr-in-Charge and as per drg.

(d) Removing of old U/S ply wood from back of hat stand and S&F new ply wood 6 mm thick commercial ISI marked duly French polished all as per drg

(e) French polishing with high class finish, including preparation by proper sand papering. All as specified & directed by Engineer-in-Charge and all as per drg.

REPAIRS TO TABLE DINING 8 PERSONS: FD-30(M),FD-239,FD-273,FD-376

(a) Removing of old U/S existing top from table and S&F new top of size as per drg. Top shall be 18mm thick MDF board as approved by GE, conforming to IS-12823 Grade-I type-II exterior grade duly screwed shade shal be Bavarian Beech. Edging all round the top shall be of 04mm teak wood

(b) Removing of old U/S leg and S&F new leg made out of Teak Wood as per drg duly finished and completed to match the existing surfaces of the item.

(c) Removing the existing u/s long rail from Table Dining 08 Pers and S&F new long rail made out of Teak Wood duly finished & completed to match the original as shown on Drg as directed

(d) Removing the existing u/s Short Rail from Table Dining 08Pers and S&F new short rail made out of Teak Wood duly finished & completed to match the original as shown on Drg as directed

(e) Removing the existing u/s Stiffners fromTable Dining 08Pers and S&F new Stiffners made out of Teak Wood duly finished & completed to match the original as shown on Drg as directed

(f) French Polishing to Table Dining 08 Pers

REPAIRS TO TABLE DINING 6 PERSONS: FD-30(M),FD-239,FD-269,FD-273

(a) Removing of old U/S existing top from table and S&F new top of size as per drg. Top shall be 18/19mm thick MDF board as approved by GE conforming to IS-12823 Grade-I type-II exterior grade duly screwed shade shal be Bavarian Beech. Edging all round the top shall be of 04mm teak wood

(b) Removing of old U/S leg and S&F new leg made out of Teak Wood as per drg including french polishing to repaired portion only to match the existing surfaces of the item

(c) Removing the existing u/s long rail from Table Dining 06 Pers and S&F new long rail made out of Teak Wood duly finished & completed to match the original as shown on Drg as directed

(d) Removing the existing u/s Short Rail from Table Dining 06 Pers and S&F new short rail made out of Teak Wood duly finished & complete to match the original as shown on Drg as directed

(e) Removing the existing u/s Stiffners fromTable Dining 06 Pers and S&F new Stiffners made out of Teak Wood duly finished & completed to match the original as shown on Drg as directed by Engr-in- charge/ GE

(f) French Polishing to Table Dining 06 Pers

REPAIRS TO TABLE 900X900X760MM: FD-88(M),FD-94(M),FD-291,FD-352

(a) Removing of old U/S existing top from table and S&F new top of size as per drg. Top shall be 18/19mm thick MDF board as approved by GE conforming to IS-12823 Grade-I type-II exterior grade duly screwed shade shal be Bavarian Beech. Edging all round the top shall be of 04mm teak wood

(b) Removing of old U/S leg and S&F new leg made out of Teak Wood as per drg duly finished and completed to match the existing surfaces of the item

(c) Removing the existing u/s long rail/Short Rail from Table 900X900X760mm and S&F new long rail made out of Teak Wood duly finished and completed to match the original as shown on Drg as directed by Engr-in- charge/ GE

(e) Removing the existing u/s Stiffners from Table 900X900X760mm and S&F new Stiffners made out of Teak Wood duly finished & complete to match the original as shown on Drg as directed by Engr-in- charge/ GE

(f) French Polishing to Table 900X900X760mm

Table 4'x3' (1200x900) FD-273

(a) Removing of old U/s existing top surface and S&F new top of size as per drg. Top shall be 18/19mm thick MDF board as approved by GE conforming to IS-12823 Grade-I type-II exterior grade duly screwed shade shal be Bavarian Beech. Edging all round the top shall be of 04mm thick teak wood. All exposed faces of timber shall be treated with french polish as directed

(b) Removing of old u/s leg and S&F new leg made out of Teak Wood complete as shown on drg

(c) Removing of old u/s long rail and S&F new long rail made out of Teak Wood size & other details complete as shown on drawing.

(d) Removing of old U/s short rail and S&F new short rail made out of Teak Wood size & other details complete as shown on drawing.

(e) Removing the existing u/s Stiffners from Table 1200x900mm and S&F new Stiffners made out of Teak Wood duly finished & completed to match the original as shown on Drg as directed by Engr-in- charge/ GE

(f) French Polishing to Table 1200x900mm

REPAIRS TO TABLE 900X600X760MM (WITH AND WITHOUT DRAWER) FD-41(M), FD-42(M),FD-55(M),FD-223,FD-224,FD-283,FD-284

(a) Removing of old U/S existing top from Table 900x600x760mm (With & without drawer) and S&F new top of size as per drg. Top shall be 18/19mm thick MDF board as approved by GE conforming to IS-12823 Grade-I type-II exterior grade duly screwed shade shal be Bavarian Beech. Edging all round the top shall be of 04mm teak wood

(b) Removing of old U/S leg from Table 900x600x760mm (With & without drawer) and S&F new leg made out of Teak Wood as per drg, duly finished & completed to match the existing surfaces of the item

(c) Removing the existing u/s long rail from Table 900X600X760mm (With and without drawer) and S&F new long rail made out of Teak Wood duly finished & completed to match the original as shown on Drg as directed by Engr-in- charge/ GE

(d) Removing the existing u/s Short Rail from Table 900X600X760mm (With and without drawer) and S&F new long rail made out of Teak Wood duly finished & completed to match the original as shown on Drg as directed by Engr-in- charge/ GE

(e) Removing the existing u/s Stiffners from from Table 900X600X760mm (With and without drawer) and S&F new Stiffners made out of Teak Wood duly finished & completed to match the original as shown on Drg as directed by Engr-in- charge/ GE

(f) Removing the existing u/s Drawer from from Table 900X600X760mm (With drawer) and S&F new Drawer made out of 12mm plywood duly fixed the S/S Knobs etc.

(g) French Polishing to Table 900X900X760mm

Supply and Fixing 15mm Dia PVC Bush on the legs of Table with 10mm long S/S Screw (various types and Drgs) small sizes

Supply and Fixing 20mm Dia PVC Bush on the legs of Table with 15mm long S/S Screw (various types and Drgs) Large sizes

M&L Spray painting 02coat of synthetic enamel Paint of silvar metalic shade/colour (outer side) and OG/Smoke Gray colour paint (inner side) (as require & directed) on old painted surface with high class finish, including necessary scrapping, denting, smoothness the surface by cleaning, removing of old paint marks etc, rubbing with sand paper, filling gaps/holes /bore holes etc with paste filler to under mentioned items complete all as specified & directed

(a) Almirah large steel with shelves and Almirah half hanging & half shelves (Complete internal and external surface) FD-67(M),FD-104(M),FD-114(M),FD-351,FD-389,FD-1031, FD-1033,FD/E6/MAP/18

(b) Almirah steel Medium with shelves and Almirah steel small half hanging & half shelves (Complete internal and external surface)FD-67(M),FD-114(M), FD-115(M),FD-243,FD-350,FD-1032,FD-1034

M&L Spray painting two coat of synthetic enamel Paint of smoke grey colour on old painted surface with high class finish including necessary scrapping, denting and to smoothness the surface by cleaning, removing of old paint marks etc, rubbing with sand paper, filling gaps/ holes/ bore holes etc with paste filler to under mentioned items complete all as specified and directed by Engr-in-charge/GE

(a) Almirah large steel with shelves and Almirah half hanging & half shelves (Complete internal and external surface)FD-67(M),FD-104(M), FD-114(M),FD-351,FD-389,FD-1031,FD-1033,FD/E6/MAP/18

(b) Almirah steel Medium with shelves and Almirah steel small half hanging & half shelves (Complete internal and external surface)FD-67(M),FD-114(M), FD-115(M),FD-243,FD-350,FD-1032,FD-1034

(c) Book Shelf open small/Large steel/Book case steel/cabinet Map steel (Complete internal and external surface)FD-90(M),FD-1028,FD-397

(d) Table office officer steel (Complete internal and external surface)FD-84,FD-1002,FD-1003

(e) Table office Clerk Steel (Complete internal and external surface)FD-84,FD-1004

(f) Book case steel / cabinate filing (Complete internal and external surface).FD-1028

(g) Locker bed side steel (Complete internal and external surface).FD-127,FD-1029

(h) Table dining OR’s steel/Table 1520x860x760mm steel (Complete internal and external surface)FD-165(M),FD-90(M), FD-1010

(j) Table table 3x2 with & without drawers steel and Table 3'x3' steel (Complete internal and external surface)FD-142(M),FD-1009,FD-1014,FD1006,FD-1007,FD-1008

(k) Rack six tier Steel / four tier FD-129(M),FD-1038

M&L Spray painting two coat of synthetic enamel Paint of black colour on old painted surface with high class finish including necessary scrapping, denting & to smoothness the surface by cleaning, removing of old paint marks etc, rubbing with sand paper, filling gaps/ holes/bore holes etc with paste filler to under mentioned items complete all as specified & directed by Engr-in-charge

Rack shoes steel FD/E6/MAP/02(R)

M&L Spray painting two coat of synthetic enamel Paint of white colour on old painted surface with high class finish including necessary scrapping, denting and to smoothness the surface by cleaning, removing of old paint marks etc, rubbing with sand paper, filling gaps/ holes/bore holes etcwith paste filler to under mentioned items complete all as specified & directed by Engr-in-charge

Stool steel 305x305x510 mm FD 81(M),FD-409

Repair to Almirah large Steel with Shelves/Almirah (L) Steel half hanging & half Shelves FD-67(M),FD-104(M), FD-114(M),FD-351,FD-389,FD-1031,FD-1033,FD/E6/MAP/18

(a) Removing old broken hinges and fixing new hinges of existing shape and size through gas welding complete all as specified and directed

(b) Removing of U/S lock and S&F New lock of 7lever with duplicate key of best quality fancy type of existing shape and size complete all as specified and directed

(c) Removing of unsv/Broken handles and S&F new Chromium Plated handle of existing shape and size complete all as specified and directed

(d) Removing of U/S & rusted legs and S&F new legs made out of MS Sheet 1.6mm thick of existing shape and size complete all as specified and directed

(e) Removing of U/S & rusted shutters and S&F new shutter made out of MS Sheet 1.00mm thick of existing shape and size complete all as specified and directed

(f) Removing of U/S & rusted shelves and S&F new shelves made out of MS sheet 1.00 mm thick of existing shape and size complete all as specified and directed

(g) Providing MS clamps of suitable pattern to the shelves to hold shelves of existing shape and size complete all as specified and directed

(h) Removing existing u/s brass Bush Barrel and S&F new Brass Bush Barrel of suitable pattern to the locking system of Almirah steel of existing shape & size complete all as specified & directed

(j) Removing existing u/s 03Way locking device and S&F new 03way locking device with plunger rod MS complete to match the original of suitable pattern to the locking system of Almirah steel of existing shape and size complete all as specified and directed

Repair to Almirah Steel Medium/Small with shelves: FD-67(M),FD-114(M),FD-115(M),FD-243,FD-350,FD-1032, FD-1034

(a) Removing old broken hinges and fixing new hinges of existing shape and size through gas welding complete all as specified and directed

(b) Removing of U/S lock and S&F New lock of 7lever with duplicate key of best quality fancy type of existing shape and size complete all as specified and directed

(c) Removing of unsv/Broken handles and S&F new Chromium Plated handle of existing shape and size complete all as specified and directed

(d) Removing of U/S & rusted legs and S&F new legs made out of MS Sheet 1.6mm thick of existing shape and size complete all as specified and directed

(e) Removing of U/S & rusted shutters and S&F new shutter made out of MS Sheet 1.00mm thick of existing shape and size complete all as specified and directed

(f) Removing of U/S & rusted shelves and S&F new shelves made out of MS sheet 1.00 mm thick of existing shape and size complete all as specified and directed

(g) Providing MS clamps of suitable pattern to the shelves to hold shelves of existing shape and size complete all as specified and directed

(h) Removing existing u/s Bush Barrel and S&F new Brass Bush Barrel of suitable pattern to the locking system of Almirah steel of existing shape & size complete all as specified & directed

(j) Removing existing u/s 03Way locking device and S&F new 03way locking device with plunger rod MS complete to match the original of suitable pattern to the locking system of Almirah steel of existing shape and size complete all as specified and directed

Repair to Book Case Steel 66"x33"x2' with glass FD-90(M),FD-1028,

(a) Removing of u/s plain glass, S&F new one 76cm x 22cm x 5mm plain glass fixed as in repaired of existing shape and size complete all as specified and directed

(b) Removing of U/S lock and S&F New lock of 4 lever with duplicate key of fancy type of existing shape and size complete all as specified and directed

(c) Removing of unsv handles and S&F new handle chrominium plated of existing shape and size complete all as specified and directed

Table office clk steel FD-84,FD-1004

(a) Removing of existing UNSV top and S&F new top made of 18/19mm prelaminated MDF board of shade bavarian beech exterior Grade ISI OSL of existing shape & size complete all as specified and directed. Edging all round the top shall be 4mm teak wood duly polished & finished

(b) Removing of steel UNSV drawer and S&F new steel drawer made out of MS Sheet of existing shape and size complete all as specified and directed & including fixing with 02 Nos of suitable sliding channels.

(c) Removing of existing u/s legs and S&F new legs of required shape & size as per drg direction by Engr-in-Charge

Table 3'x2' Steel with drawer and w/o drawer FD-1006, FD-1007,FD-1008

(a) Removing of existing UNSV top and S&F new top made of 18/19mm prelaminated MDF board exterior Grade ISI OSL of existing shape and size complete all as specified and directed. Edging all round the top shall be 4mm teak wood duly finished and polished. Prelaminated MDF board shade colour shall be bararian beech as per directed by engr-in-Charge

(b) Removing of steel UNSV drawer and S&F new steel drawer made of MS Sheet of existing shape and size complete all as specified and directed & including fixing with 02Nos of suitable sliding channels.

(c) Removing of existing u/s legs and S&F new legs of required shape & size as per drg direction by Engr-in-Charge

Table 3'x3' steel FD-142(M),FD-1009,FD-1014

(a) Removing of existing UNSV top and S & F new top made of 18/19mm prelaminated MDF board exterior Grade ISI OSL of existing shape and size complete all as specified and directed. Edging all round the top shall be 4mm teak wood duly finished and polished. Prelaminated MDF board shade colour shall be bararian beech as per directed by engr-in-Charge

(b) Removing of existing u/s legs and S&F new legs of required shape and size as per drg as directed by Engr-in-Charge

Table office officer steel FD-84,FD-1002,FD-1003

(a) Removing of existing UNSV top and S & F new top made of 18/19mm prelaminated MDF board exterior Grade ISI OSL of existing shape and size complete all as specified and directed. Edging all round the top shall be 4mm teak wood duly finished and polished Prelaminated MDF board shade colour shall be bararian beech as per directed by engr-in-Charge

(b) Removing of steel UNSV drawer and S&F new steel drawer made of MS Sheet of existing shape & size complete all as specified & directed, including fixing with 02Nos of suitable sliding channels

(c) Removing of existing u/s legs and S&F new legs of required shape & size as per drg direction by Engr-in-Charge

Welding of broken steel furniture.FD-243,FD-1032, FD-1046,FD-1004,FD-1008,FD-1007,FD-562,FD-1014, FD-362,FD-1003, FD-75,FD-165(M), FD-75(M),FD-256 (Steel items ofvarious drgs)

(a) Gas Welding point (01 inch) on Broken part of steel furniture shall be carried out such as Almirah large steel with shelf/Wo shelf and Half hanging, Almirah med steel/small with shelf, Locker bed side steel, Table office clk steel, table 3x2 steel w/d, Locker SKD 562 of chair CB steel with arms/ without Arms, chair verandah, table dining, table office, officer/clerk steel, chair easy steel, teapoy verandah & Steel items of various drgs etc. welding shall be done continuously type, including rubbing and finishing to smooth surface

REPAIRS TO TEAPOY VARANDAH FD-35(M),FD-208, FD-255,FD-383

(a) Removing of old U/S existing top from table and S&F new Top of size 900x450x18mm for teapoy verandah. Top shall be 18/19 mm thick MDF board exterior grade as approved by GE conforming to IS-12823 Grade-I type-II duly shade shal be Bavarian Beech screwed. Edging all round the top shall be of 4mm teakwood. steel frame should be painted with 02 coats of white paint shall be done on entire frame of teapoy varandha as per direction by Engr-in-charge

Repair/Refixing ply top charpoy GI FD-220

(a) Removing of old U/S plywood and S&F new 12mm thickness plywood top of size 1980x900 mm exterior grade BWR type (Nos of ply 7) ISI marked fixed with flat/dome head MS galvanished iron carriage bolts. The edge of plywood shall be smoothened alround & corner shall be rounded to a radious of 1cm iron carriage, 10Nos of round headed bolts with nut & washer of size 5x75mm after drilling the holes at equal distance on rails (03Nos on each long rail & 02Nos on each Short Rails) & all as directed by the Engr-in-Charge/GE & as per shown on drg

(b) Removing of Old/unsv Long rails from charpoy GI Pipe and S&F of new long rail made out of GI Pipe 32mm nominal dia Med Grade duly threaded at both end upto 45mm & all as directed by the Engr-in-Charge Note : U/S long rails be converted into 01short rail & 01leg & measured in Sch No. 29.03 (c) & 29.04(d)

(c) Removing of Old/unsv Short rails from charpoy GI Pipe and fixing only Short rail retrieved and made out from schedule No 18(b) duly threaded at both end upto 45mm & all as directed by the Engr-in-Charge Note: U/S Short rails be converted into 01leg and measured in Sch 18 29.04(d)

(d) Removing of Old/unsv Legs from charpoy GI Pipe and fixing only legs retrieved made out from old long rails/short rails, retrieved under item Sl No 29.02 (b) & 29.03(c) here in before duly threaded at one end upto 45mm and all as directed by the Engr-in-Charge

(e) Re-threading of existing loose long rails, short rails and legs of 32mm dia GI Pipe upto 45mm and assembling to make a charpoy frame complete as shown on drawing and as directed by Engr-in Charge/GE Note: Old existing loose long rails, short rails and legs shall be issued to the Contractor for re-threading and assembling it to make a charpoy frame

(f) Removing of Old/unsv broken existing elbow of charpoy GI pipe and S&F new elbow GI 03Way 32mm Med Grade ISI marked of existing shape and size complete all as specified & directed

(g) Removing of Old/unsv broken existing check nut of charpoy GI pipe and S&F new elbow check nut 32mm Med Grade ISI marked of existing shape and size complete all as specified & directed

Chair CBA Special with hand rest FD-120

(a) Removing of U/S 20mm thick TW Back Frame duly canned with plastic cane 02mm and S&F new TW plank with plastic caning godraj pattern of existing shape and size complete all as specified & directed

(b) Removing of U/S 20mm thick TW seat Frame duly canned with plastic cane 02mm and S&F new TW plank with plastic caning godraj pattern of existing shape and size complete all as specified & directed

(c) Removing of old unsv 12mm thick TW plank and S&F 20mm thick plank fixed with required size & shape of round tube fixed as in repairs as shown on Drg and of existing shape and size complete all as specified & directed

(d) Removing of old unsv 20mm Arms, supply & fixing new arms made out of seasoned hard wood, Shisham duly painted with synthetic enamel black paint and shall be fixed with steel screws of existing shape and size complete all as specified & directed

Re-canning of chairs Varandhah FD-19(M),FD-256, FD-259,FD-359

(a) Removing of old broken plastic cane and recaning of chair varandah with & including new plastic cane of 03/04mm semi round, white colour, best quality of approved including painting with two coats of white synthetic enamelled paint on entire steel/iron surfaces of chair before recaning & including provn of new PVC shoes 20mm dia at bottom of legs after taking out old shoes all as specified including all material & labour, canning shall be done in Matt pattern

Repair to Chair CB Steel with Arms/Chair Steel tabular with Arms FD-75 (M)

(a) Removing of old broken seat and S&F new seat of existing shape and size made from seasoned hardwood (Shisham) duly caned with 02mm semi/half round plastic cane of white colour as per Godrej pattern and frame of seat shall be finished/painted with black colour synthetic enamel paint complete all as specified & directed

(b) Removing of old broken Back and S&F new Back of existing shape and size made from seasoned hardwood (Shisham) duly caned with 02mm semi/half round plastic cane of white colour as per Godrej pattern and frame of seat shall be finished/painted with black colour synthetic enamel paint complete all as specified & directed

(c) Painting to steel frame chairs CB steel with one coat of olive green enamelled paints of approved brand.

(d) Removing of old unsv Arms, supply & fixing new arms of existing shape and size made out of seasoned hard wood, Shisham duly painted with synthetic enamel black paint and shall be fixed with steel screws complete all as specified & directed

(e) M&L for provide 25x5mm flat iron support 50mm long 4Nos each chair under bottom of seat welded with frame complete all as specified and directed

Repair to Chair CB Steel without Arms/Chair Steel tabular without Arms FD-75 (M)

(a) Removing of old broken seat and S&F new seat of existing shape and size made from seasoned hardwood (Shisham) duly caned with 02mm semi/half round plastic cane of white colour as per Godrej pattern and frame of seat shall be finished/painted with black colour synthetic enamel paint complete all as specified & directed

(b) Removing of old broken Back and S&F new Back of existing shape and size made from seasoned hardwood (Shisham) duly caned with 02mm semi/half round plastic cane of white colour as per Godrej pattern and frame of seat shall be finished/painted with black colour synthetic enamel paint complete all as specified & directed

(c) Painting to steel frame chairs CB steel with one coat of olive green enamelled paints of approved brand.

(d) M&L for provide 25x5mm flat iron support 50mm long 4Nos each chair under bottom of seat welded with frame complete all as specified & directed complete all as specified & directed

Supply and Fixing 15/20/25mm Dia PVC/Rubber Bush on the legs of Table (various types and Drgs) small & large sizes

Supply and Fixing 15/20/25mm suqare PVC/Rubber Bush on the legs of Table (various types and Drgs) small & Large sizes

REPAIRS TO CHAIR DINING. FD-16(M),FD-203,FD-228,FD-279

Removing of old U/s front leg and S&F new front leg made out of teak wood of existing shape & size complete to match the original as shown on Drg as directed

Removing of old U/s rear leg and S&F new rear leg made out of teak wood of existing shape & size complete to match the original as shown on Drg as directed

Removing of old U/s front/back rails and S&F new front/back rails (including holes for canning) made out of teak wood of existing shape & size complete to match the original as shown on Drg as directed

Removing of old U/s side rails and S&F new side rails (including holes for canning) made out of teak wood all of existing shape & size complete to match the original as shown on drg

Tightening of Chair dining complete, loose joints shall be done by necessary nails wood corner suitable size shall be required on site as direction by Engr-in-Charge

Removing of old U/s stiffeners and S&F new stiffeners made out of teak wood of existing shape & size complete to match the original as shown on Drg as directed

M&L French Polishing to chairs with high class finish including preparation of surfaces by proper sand papering complete all as specified and as shown on drawing.

REPAIRS TO CHAIR EASY FD/CHAIR EASY NF FD-17(M), FD-201,FD-229,DB-4174

Removing of old U/s front leg and S&F new front leg made out of teak wood of existing shape & size complete to match the original as shown on Drg as directed

Removing of old U/s rear leg and S&F new rear leg made out of teak wood of existing shape & size complete to match the original as shown on Drg as directed

Removing of old U/s side rails and S&F new side rails (including holes for canning) made out of teak wood of existing shape & size complete to match the original as shown on drg

Removing of old U/s front/back rails and S&F new front/back rails (including holes for canning) made out of teak wood of existing shape & size complete to match the original as shown on Drg as directed

Tightening of Chair easy compete, loose joints shall be done by necessary nails wood corner suitable size shall be required on site as direction by Engr-in-Charge.

Removing of old U/s stiffeners and S&F new stiffeners made out of teak wood of existing shape & size complete to match the original as shown on Drg as directed

Removing of old U/s hand rest and S&F new hand rest made out of teak wood of existing shape & size complete to match the original as shown on Drg as directed

M&L French polishing to chair shall be done with high class finish including pre-paration of surfaces by proper sand papering complete all as specified & as shown on drg

REPAIR TO CHAIR WRITING/CHAIR CB OFFICE FD-20(M),FD-202,FD-250,FD-280

Removing of old U/s front leg and S&F new front leg made out of teak wood of existing shape & size complete to match the original as shown on Drg as directed

Removing of old U/S rear legs and S&F rear legs made out of teak wood of existing shape & size complete to match the original as shown on Drg as directed

Removing ofold u/s side rails and S&F new side rails (including holes for canning) made out of teak wood of existing shape & size complete to match the original as shown on drg as directed

Removing of old U/s front/back rails and S&F new front/back rails (including holes for canning) made out of teak wood of existing shape & size complete to match the original as shown on Drg as directed

Tightening of Chair writing complete, loose joints shall be done by necessary nails wood corner suitable size shall be required on site as direction by Engr-in-Charge.

Removing of old U/s stiffeners and S&F new stiffeners made out of teak wood of existing shape & size complete to match the original as shown on Drg as directed

Removing of old U/s hand rest and S&F new hand rest made out of teak wood of existing shape & size complete to match the original as shown on Drg as directed

M&L French polishing to repaired chairs with high class finish including preparation of surfaces by proper sand papering complete all as specified and as shown on drawing

RE-CANNING OF VARIOUS TYPES OF FURNITURE FD-16(M),FD-203,FD-228,FD-279,FD-17(M), FD-201,FD-229,DB-4174,FD-20(M),FD-202,FD-250,FD-280,FD15(M),FD-27(M), FD-212,FD-244,FD-385,FD-252 & various items of Canned furniture

M&L for removing of old/broken/ unservisable plastic cane & re-canning of chair dinnig, chair CB without arms/chair writing,chairs CB with arms,chairs writing, chair CB office, chair easy FD/NF, chair, stool dressing CB, Couch set & bin solied linen with 2 to 2.5mm semi round cane plastic of white colour and border with 3 to 4mm semi round cane plastic of white colour. Rest all as per drgs. The canning work shall be done in Godraj pattern. Cane should be in White colour (Non recycled) & make as approved

Repairs to Computer table FD/E6/MAP/03/TP

Removing of UNSV top and S&F new top of prelaminated MDF board exterior grade 18mm thick Grade-I, Type-II exterior grade of appproved make (Covered with 4mm thick teek wood/PVC beading duly polished) of existing shape & size complete to match the original as shown on Drg as directed

Removing of UNSV side and S & F new side of prelaminated MDF board exterior grade 18 mm thick grade-I, type-II, exterior grade of approved make of existing shape & size complete to match the original as shown on Drg as directed

Removing of Broken/UNSV keyboard and S&F new keypad of prelaminated MDF board exterior grade with sliding arrangement /telescopic rails both sides of key board of existing shape & size complete to match the original as shown on Drg as directed

Removing of UNSV drawer & S&F new drawer with sliding arrangement/ telescopic rails both sides of drawer including of 4leaver lock as per Godrej pattern of existing shape & size complete to match the original as shown on Drg as directed

Removing of UNSV base/bottom cabinet and S&F of new bottom cabinet of 18mm thick pre- laminated MDF board exterior grad 18mm thick grade-I, type-I of existing shape & size complete to match the original as shown on Drg as directed

Repairs to Computer chair revolving/ High Back and Med Back FD/E6/MAP/01/TP

Removing of existing u/s 4/5 prong Base and S&F new mild steel 5 prong base of existing shape & size complete to match the original as shown on Drg as directed complete with suitable nuts & bolts to chair revolving steel of various types

Removing of existing u/s foam cushion & tapestry cloth (seat & back) and S&F suitable foam cushion 50mm thick & 32mm density of existing shape & size complete to match the original as shown on Drg as directed covered with new tapestry cloth (seat & back) (of approved type/ design/ colour) (Cloth shall not be less than 300/- per RM) alongwith all around suitable PVC strip duly stitched & fixing to chair revolving steel, of various types

Removing of existing u/s tapestry cloth (seat & back) and S&F suitable new tapestry cloth (seat & back) (of approved type/ design/ colour) of existing shape & size complete to match the original as shown on Drg (Cloth shall not be less than 300/- per RM) alongwith all around suitable PVC strip duly stitched and fixing to chair revolving steel of various types

Removing of existing u/s leatherite (seat & back) and S&F new black leatherite cloth (seat & back) (of approved type/design/colour) of existing shape & size complete to match the original as shown on Drg (Leathrite cloth shall not be less than 350/-per RM) alongwith all around suitable PVC strip duly stitched & fixing to chair revolving steel of various types

Removing of existing u/s MS bearing and S&F suitable MS bearing of existing shape & size complete to match the original to chair revolving steel of various types as shown on Drg

Removing of existing u/s caster wheels and S&F suitable caster wheels of existing shape & size complete to match the original as shown on Drg as directed with suitable nuts & bolts to chair revolving steel of various types.

Removing of existing u/s Hydraulic system and S&F suitable Hydraulic system of existing shape & size complete to match the original as shown on Drg as directed to chair revolving steel of various types

Removing of existing u/s Hand rest and S&F suitable Hand rest of rubberised PVC of existing shape & size complete to match the original as shown on Drg as directed with suitable nuts & bolts as to match with the existing to chair revolving steel of various types

Repairs to Chair Writing MAP/ Chair Visitor FD/E6/MAP/12/TP

Removing of existing u/s foam cushion & tapestry cloth (seat & back) and S&F suitable foam cushion 50mm thick & 32mm density of existing shape & size complete to match the original as shown on Drg as directed covered with new tapestry cloth (seat & back) (of approved type/ design/ colour) (Cloth shall not be less than 300/- per RM) alongwith all around suitable PVC strip duly stitched & fixing to chair revolving steel, of various types

Removing of existing u/s tapestry cloth (seat & back) and S&F suitable new tapestry cloth (seat & back) (of approved type/ design/ colour) of existing shape & size complete to match the original as shown on Drg (Cloth shall not be less than 300/- per RM) alongwith all around suitable PVC strip duly stitched and fixing to chair revolving steel of various types

Removing of existing u/s leatherite cloth (seat & back) and S&F new black leatherite cloth (seat & back) (of approved type/design/colour) of existing shape & size complete to match the original as shown on drg (Leathrite cloth shall not be less than 350/-per RM) along with all around suitable PVC strip duly stitched & fixing to chair revolving steel of various types

Removing of existing u/s Hand rest and S&F suitable Hand rest of rubberised PVC of existing shape & size complete to match the original as shown on Drg as directed with suitable nuts & bolts as to match with the existing to chair revolving steel of various types

Removing of Old/unsv PVC Rings/Rubber shoes to chair visitor steel/ chair writing map/ chair conference hall.

Repairs to Side Board FD-26(M),FD-150(M),FD-241,FD-371,FD-372,FD-391,FD-1112

Removing the existing u/s shelves from side board and S&F to new shelves made out of 12mm plywood of existing shape & size complete to match the original as shown on Drg

Removing the existing u/s Top from side board and S&F to new Top made out of 18/19mm MDF board of existing shape & size complete to match the original as shown on drg

Removing the existing u/s Doors from Side board and S&F to new Doors made out of 18/19mm MDF board of duly fixed the S/S Knobs etc of existing shape & size complete to match the original as shown on Drg as directed

Removing of old U/S broken Knobs of side board and S&F new CP Knobs of existing shape & size complete to match the original as shown on Drg as directed

Removing of old U/s drawer with knobs and providing new drawer made out of 12mm thick MDF board for side and 06mm thick ply wood commercial for bottom including knobs CP of existing shape & size complete to match the original as shown on Drg as directed

Removing the existing u/s Base from Side board and S&F to new Base made out of 18/19 mm MDF board of existing shape & size complete to match the original as shown on drg

Removing the existing u/s Sides from side board and S&F new sides made out of 18/19mm MDF board of existing shape & size complete to match the original as shown on drg

Removing the existing u/s Back ply from side board and S&F new back ply made out of 06 mm plywood commercial of existing shape & size complete to match the original as shown on drg

Repair/Refixing ply top charpoy GI pipe FD-220

Removing of old U/S plywood and S&F new 12mm thick plywood top of size 1980x900mm exterior grade BWR type (Nos of ply 7)ISI marked fixed with flat/dome head MS galvanished iron carriage bolts. The edge of plywood shall be smoothened alround & corner shall be rounded to a radious of 1cm iron carriage, 10Nos of round headed bolts with nut & washer of size 5x75mm after drilling the holes at equal distance on rails (03Nos on each long rail & 02Nos on each Short Rails) & all as directed by the Engr-in-Charge/GE & as shown on drg

Removing of Old/unsv Long rails from charpoy GI Pipe and S&F of new long rail made out of GI Pipe 32mm nominal dia Med Grade duly threaded at both end upto 45mm & all as directed by the Engr-in-Charge Note : U/S long rails be converted into 1short rail & 1leg & measured in Sch No 50.03 & 50.04

Removing of Old/unsv Short rails from charpoy GI Pipe and fixing only Short rail retrieved and made out from schedule No 18(b) duly threaded at both end upto 45mm & all as directed by the Engr-in-Charge Note: U/S Short rails be converted into 01leg and measured in Sch 50.04

Removing of Old/unsv Legs from charpoy GI Pipe and fixing only legs retrieved made out from old long rails/short rails, retrieved under item Sl No 50.02 & 50.03 here in before duly threaded at one end upto 45mm and all as directed by the Engr-in-Charge

Re-threading of existing loose long rails, short rails and legs of 32mm dia GI Pipe upto 45mm and assembling to make a charpoy frame complete as shown on drawing and as directed by Engr-in Charge/GE Note: Old existing loose long rails, short rails and legs shall be issued to the Contractor for re-threading and assembling it to make a charpoy frame

Removing of Old/unsv broken existing elbow of charpoy GI pipe and S&F new elbow GI 03 Way 32mm Med Grade ISI marked of existing shape and size complete all as specified & directed

Removing of Old/unsv broken existing check nut of charpoy GI pipe and S&F new elbow check nut 32mm Med Grade ISI marked of existing shape and size complete all as specified & directed

Provn of 01 No of flat iron MS strip of size 900mm x 32mm x 3mm at the center of long rails of Charpoy GI Pipe, duly 01 coat of red oxide & 02 coat of black synthetic enamel paint as directed by the Engr-in-Charge/GE

Provn of 02Nos clamps made out of MS flat iron 25x3mm to hold the MNF set made to shape, lower clamp duly plugged/sealed by welding with 3.0mm thick MS black sheet on each leg of Charpoy GI Pipe duly painted with 02coats of black synthetic enamel paint over a coat of red oxide primer as specified directed

M&L for polishing with French polish to under mentioned item of furniture articles (of messes, Units, IB etc) with high class finish after rubbing old polish. The surfaces shall be rubbed down to smoothness with sand paper, the porous in wood shall be filled with filler solution as directed

Almirah large wooden with shelves/without shelves, half hanging & half shelves, Almirah small with shelves/Almirah Med, half hanging and half shelves, Almirah mess utensil/Almirah Map, Book shelf open small/large, Book Case wooden/Book case library pattern FD-45(M),FD-65(M), FD-93(M),FD-109,FD-110,FD-147, FD-335,FD-355,FD-356,TP

Bed ply wood top/Bed Hard Wooden/Bed Newar, Double Bed Trade Pattern FD-213,FD-214,FD-245,FD-1121,FD-247,FD-1102,FD-1120,FD-246,TP

Bin linen small/large.FD15(M),FD-212,FD-244,FD-385

Chair writing/CBA/CB office/CBB/dining/Chair easy FD/NF/Chair wooden bottom (BKB)/BKA/Chair CBA with hand rest, Chair Dining Long Back (TP), Chair Easy(TP), Chair Wiriting Wooden (TP) etc.FD-16(M),FD-17(M),FD-20(M),FD-56(M),FD-148,FD-149,FD-201,FD-202,FD-203,FD-225, FD-228,FD-229,FD-250,FD-279,FD-280,FD-285, DB-4174,TP & Long Back Dining Chairs

Mirror Frame (TP), Hat stand with mirror, Decorative Frame FD-23(M),FD-206,FD-233,FD-361,FD-362,TP

Side board all type FD-26(M),FD-241,FD-150(M),FD-371,FD-372,FD-391,FD-1112,TP

Stool dressing various type FD-27,FD-1114,TP

Table writing Med/Table writing FD/Table office clerk wooden/Table office officer wooden/Table 900x900x760mm /Table 3’x2’ with or without drawer/Table writing cadets/Table Examination/Table one piece/Table two pieces for all purposes/ Table dining 6 Pers FD-30(M),FD-41(M), FD-42(M),FD-55(M),FD-88(M),FD-94(M),FD-223,FD-224, FD-239,FD-352,FD-269,FD-273,FD-376,FD-283,FD-284,FD-291 & all types of LargeTables of Trade Pattern

Table peg/Table centre/teapoy FD wooden/Table bed side FD with and without drawer FD-25(M),FD-29(M),FD-34(M),FD-134(M),FD-152(M),FD-210,FD-232,FD-235,FD-236,FD-248, FD-266,FD-274,FD- 276,FD-277,FD-278,FD-382,FD-384,FD-393 & all types of small Tables of Trade Pattern

Table dressing Gents with mirror/Table dressing ladies with mirror FD-31(M),FD-32(M),FD-230,FD-251,FD-378,FD-379,TP & various dessing table/chests

Sofa set 4 seated/5 seated cushened FD-154,FD-272, FD-281,FD-373,FD/MAP-II/02,TP

Decorative corner stands TP

Screen Movable Wooden TP & various drg of screen movable (W)

Supply and Fixing 15mm Dia PVC Bush on the legs of Wooden Chairs Various Types with 10mm long S/S Screw (various types and Drgs)

REPAIRS TO BED PLY TOP FD-213,FD-214,FD-245, FD-246,FD-247

(a) Removing of old u/s head board and S&F new head board made out of teak wood frame of size 900x600mm including leg and 04mm thick both side teak face ply ISI marked for both sides & complete teak wood beading shall be provided all over complete all as directed

(b) Removing of old u/s foot board and S/F new foot board made out of teak wood frame of size 900x450mm including 04mm thick both side teak face ply ISI marked and complete 04mm thick teak wood beading shall be provided all over complete all as directed

(c) Removing of old broken long rails and S&F new long rails of shisham wood of size 1800x90x35mm long as per drg duly finished and complete all as directed.

(d) Removing of old U/S worn out ply wood top and S&F new ply wood top of size 1800x900mm of 12mm thick commercial BWR/ISI mark complete as approved by GE & rest all as per drg.

(e) Removing of old broken short rail/center stiffner and S&F new short rails/center stiffner of shisham wood of size 900x90x35mm long as per drg duly finished and complete all as directed

(f) French Polishing to Bed with plywood Top/Bed Newar

Avtarsinghchaddhaandcompany

M/SDoon furnishers