Renovation Works of Office and Godown at State Warehouse Karikode in Kollam District.

Amount

Toilet for KMSCL

Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand).All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level1:1.5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size.

Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers.All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer after preparing the surface by using wirebrush or emery paper.Fixed to openings/ wooden frames with rawl plugs screws etc.All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand).All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface after preparing the surface by using wirebrush or emery paper,all works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade after preparing the surface by using wirebrush or emery paper.All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.Two or more coats on new work

Flooring & Plumbing work

Providing and laying Ceramic anti-skid floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of Ist quality conforming to IS : 15622, of approved make, in all colours, shades laid on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 Coarse sand) including jointing with epoxy joint fillers with pigment of matching shade of approved brand in approved pattern complete.

Providing and laying Ceramic glazed wall tiles (thickness to be specified by the manufacturer), of Ist quality conforming to IS : 15622, of approved make, in all colours, shades laid on 20 mm thick bed of cement mortar 1:3 ( 1 cement : 4 Coarse sand), including tile spacers and pointing with epoxy joint fillers with pigment of matching shade of approved brand in approved pattern etc., complete.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931. including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge. 15 mm nominal bore

Providing and fixing floor trap of approved quality & make as per the direction of engineer in charge. All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 10kgf /cm2

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 32 mm pipe 10Kgf/cm2

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the wall etc. 63 mm pipe 6 Kgf/cm2

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Elbow ,complete as per direction of Engineer-in-Charge.

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63 dia 45 degree Elbow,complete as per direction of Engineer-in-Charge.

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63x63x63 mm dia Door Tee,complete as per direction of Engineer-in-Charge.

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Vent cowl,complete as per direction of Engineer-in-Charge.

Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow,complete as per direction of Engineer-in-Charge.

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x75 mm dia Door Tee,complete as per direction of Engineer-in-Charge.

Providing and fixing PVC ball valve (ISI marked) of the approved brand for Rigid PVC pipes, including jointing with PVC solvent cement;32 mm nominal bore ,complete as per direction of Engineer-in-Charge.

Providing and fixing PVC ball valve (ISI marked) of the approved brand for Rigid PVC pipes, including jointing with PVC solvent cement: 25mm nominal bore ,complete as per direction of Engineer-in-Charge.

Supplying and fixing solid PVC door of size 0.80 x 2.10 M using door frame 50x47x5mm and 30mm thick solid PVC for the shutter in single leaf including 18 nos 50 mm scews fixed in walls including all door fittings cost and conveyance of all materials required etc. complete as per instruction. during execution.

Supplying and installing ready made PVC Septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (Provision for CC/RCC/Sand/06mm aggregate for the preparation of bed shall be paid separately)35 to 50 L flush capacity.All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Constructing soak pit 1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Aluminium & false ceiling work

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285(minimum thickness of Aluminium section 1.20mm), fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron).

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

Providing and fixing Thomson Multi wood board or equivalent make paneling 12 mm thick, to frame, backing or studding with screws etc. complete ( Frames, backing or studding to be paid separately) as per the direction of site Engineer-in-charge.

Providing and fixing false ceiling with 9mm thick PVC plain panel board ceiling of approved quality at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of PVC board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing, all as per manufacturer& specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge.

Steel work in built up GI tubular (round, square or rectangular hollow tubes etc.-minimum thickness 2.00 mm) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer after preparing the surface by using wirebrush or emery paper, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes.All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Painting for KSBC and KSWC Office

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface after preparing the surface by using wirebrush or emery paper,all works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture including applying additional coats wherever required, to achieve even shade and colour, after preparing the surface by using wirebrush or emery paper,all works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.Two coats.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:One or more coats on old work, after preparing the surface by using wirebrush or emery paper,all works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

TILE LAYING

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

FALSE CEILING

Steel work in built up GI tubular(round, square or rectangular hollow tubes etc.-minimum thickness 2.00 mm) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer after preparing the surface by using wirebrush or emery paper, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes.All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Providing and fixing false ceiling with 9mm thick PVC plain panel board ceiling of approved quality at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of PVC board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge.

Scooter shed

Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 500 metres lead as per direction of Engineer-in-Charge.In cement mortar

Clearing grass and removal of the rubbish up to a distance of 500 m outside the periphery of the area cleared.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

Steel work in built up GI tubular (round, square or rectangular hollow tubes etc.-minimum thickness 2.00 mm) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer after preparing the surface by using wirebrush or emery paper, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes.All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Providing silicon compound covering to G.I. bolts over roof .All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Dry brick flooring in required pattern with available demolished bricks of existing compound wall and filling joints with available sand including levelling, watering and compacting etc. complete as per the direction of Engineer in charge.

K.S. CHANDRALAL

VINEEP M