Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹79.4 CrAccepted-AOC | ₹79.4 Cr | L1 | Accepted-AOC L1 |
| 2 | L2₹81.3 CrRejected-Finance 5TH FLOOR ALPHA PLAZA K P VALLON ROAD KADAVANTHRA KOCHI KERALA PIN 682020 | KOCHI | ERNAKULAM | KERALA | 682020 | ₹81.3 Cr | L2 | Rejected-Finance L2 |
Tender Value
₹76.0 Cr
EMD Value
₹86.0 L
Closing Date
28 Oct 2020, 3:00 pmClosed
The Managing Director, INKEL Limited
2nd Floor, Ajiyal Complex, Kakkanad, Cochin, Pin 682030
The proposed work shall consist of construction of a New Hospital Block (Ground plus six Floors), Mortuary building, MEP works and all associated utilities
2020_INKEL_390676_1
NIT/INKEL/KIIFB/2020-21/113 dated 09/10/2020
Open Tender
Civil Works - Buildings
540 days
District Hospital, Mavelikkara
As detailed in tender document
18 documents required · 18 mandatory
₹17,700
Online
₹86.0 L
Yes
Video Conference in Zoom
10 Feb 2021
9 Oct 2020
30 Oct 2020
9 Oct 2020
28 Oct 2020
21 Oct 2020
10 Oct 2020 - 14 Oct 2020
16 Oct 2020
Amount
CIVIL WORKS - Pile Foundation
Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-35 (Cement quantity-400kg/m3) of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note:Truck mounted/Rotary/TMR/Tubewell boring machine shall not be used.(Minimum cement content is 400kg/cum and no payment shall be made for extra cement.) 500 mm dia piles.
Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-35 (Cement quantity -400kg/m3) of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap).Note:Truck mounted/Rotary/TMR/Tubewell boring machine shall not be used. (Min cement content is 400kg/cum and no payment shall be made for extra cement.) 600 mm dia piles
Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-35 (Cement quantity-400kg/m3) of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note:Truck mounted/Rotary/TMR/Tubewell boring machine shall not be used.(Minimum cement content is 400kg/cum and no payment shall be made for extra cement.) 800 mm dia piles.
Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-35 (Cement quantity-400kg/m3) of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note:Truck mounted/Rotary/TMR/Tubewell boring machine shall not be used.(Minimum cement content is 400kg/cum and no payment shall be made for extra cement.) 900mm dia pile.
Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-35(Cement quantity -400kg/m3) of specified diameter and length below the pile cap, to carry a safe workingload not less than specified, excluding the cost of steel reinforcement but including the cost of boring withbentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mudcirculation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete,including removal of excavated earth with all its lifts and leads (length of pile for payment shall bemeasured up to bottom of pile cap).Note:Truck mounted/Rotary/TMR/Tubewell boring machine shall notbe used.(Min cement content is 400kg/cum and no payment shall be made for extra cement.) 1000 mm dia piles
20.6.2.1 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge.Single pile above 50 tonne and upto 100 tonne capacity Initial test
20.6.2.2 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge.Single pile above 50 tonne and upto 100 tonne capacity Routine test
Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification the direction of Engineer in-charge.Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing.Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge.Initial test up to 150 tonne capacity
Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification the direction of Engineer in-charge.Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing.Note: 2. Testing agency shall submitt the design of loading platform for the approval of Engineer-in-charge.routine test up to 150 tonnes
Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification the direction of engineer -in-Charge.Single pile of 200 tonne capacity Initial test
Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification the direction of engineer -in-Charge.Single pile 200 tonne capacity Routine test
Earth Work
2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil
2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil
2.26.1 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil
2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
Extra for every additional lead of 50 m or part there of for disposal of excavated earth and stacking
Extra for every additional lead beyond 50m upto 1Km (within the hospital compound) for disposal of excavated earth & stacking.
50.2.25.1 : Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge
60.2.3 : Bailing out water using pump above 5 HP and Up to 10 HP-Bailing out water with engine and pump set above 5HP and up to 10HP, including conveyance to site and erection,cost of fuel, lubrication oil and other stores, pay of staff etc complete
Plain cement concrete works
4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)
Reinforced cement concrete and Steel reinforcement work
Providing and laying in position machine batched and machine mixed design mix M-35 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. (Note:- Min cement content is 350kg/cum and no payment shall be made for extra cement).All work upto plinth level.
Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. (Note:- Min cement content is 340kg/cum and no payment shall be made for extra cement).All work above plinth level upto floor V level
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. (Note :- Minimum Cement content is 330 kg/cum and no payment shall be made for extra cement however contractor shall be bound to use required cement quantity as per the approved mix design).All work upto plinth level
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix,including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate,retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. (Note :- Minimum Cement content is 330 kg/cum and no payment shall be made for extra cement however contractor shall be bound to use required cement quantity as per the approved mix design).All work above plinth level upto floor V level
5.38 : Extra for R.C.C. /B.M.C/R.M.C. work above floor V level for each four floors or part thereof.
4.6.1 : Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), including the cost of required centering, shuttering complete.1:1.5:3 ( 1 cement : 1.5 coarse sand (Zone III): 3 graded stone aggregate 20 mm nominal size)
5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete
5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform
5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers
5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts
5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)
5.9.19 : Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges
5.11.1 : Extra additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)
Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete at all levels.Thermo - Mechanically Treated bars of grade Fe-500D or more
Block Work
50.6.2.3 :Solid block masonry using pre cast solid blocks (Factory made) of size 30x15x20cm or nearest available size of Grade C confirming to IS 2185 part I of 2005 for super structure above floor two level upto floor five level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete
50.6.2.2 : Solid masonry using pre cast solid blocks (factory made) of size 30x15x20cm or nearest available size of Grade C confirming to IS 2185 part I of 2005 for super structure up to floor two level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete
6.5 : Extra for brick work/ AAC block masonry/Tile brick masonry in super structure above floor V level, for each four floors or part thereof by mechanical means.
50.6.1.4 : Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size of Grade C confirming to IS 2185 part I of 2005 for foundation and plinth with thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand ) etc complete
50.6.1.5 : Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size of Grade C confirming to IS 2185 Part I of 2005 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete
50.6.1.6 : Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size of Grade C confirming to IS 2185 part I of 2005 for super structure above floor two level upto floor five level thickness 20cm and above in : CM 1:6 ( 1 cement : 6 coarse sand sand) etc complete
50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x10x20 cm or nearest available size of Grade C confirming to IS 2185 part I of 2005 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete. Providing two numbers of 8mm dia bars in every 4th layer and it will be measured in reinforcemnt item
Solid block masonry using pre cast solid blocks (Factory made) of size 40x10x20 cm or nearest available size of Grade C confirming to IS 2185 part I of 2005 for super structure above floor two level to up to floor five levels for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete. Providing two numbers of 8mm dia bars in every 4th layer and it will be measured in reinforcemnt item
Joinery Works
25.1 : Providing and supplying aluminium extruded tubular and other aluminium sectionsas per the architectural drawings and approved shop drawings , the aluminiumquality as per grade 6063 T5 or T6 as per BS 1474,including super durable powdercoating of 60-80 microns conforming to AAMA 2604 of required colour and shadeas approved by the Engineer-in-Charge. ( The item includes cost of material suchas cleats, sleeves, screws etc. necessary for fabrication of extruded aluminiumframe work. Nothing extra shall be paid on this account).
25.2 : Designing, fabricating, testing, protection, installing and fixing in position semi(grid) unitized system of structural glazing (with open joints) for linear as well ascurvilinear portions of the building for all heights and all levels, including:a) Structural analysis & design and preparation of shop drawings for the specifieddesign loads conforming to IS 875 part III (the system must passed the proof testat 1.5 times design wind pressure without any failure), including functional designof the aluminum sections for fixing glazing panels of various thicknesses, aluminiumcleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clampsetc., structural and weather silicone sealants, flashings, fire stop (barrier)-cumsmokeseals, microwave cured EPDM gaskets for water tightness, pressureequalisation & drainage and protection against fire hazard including:b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3Dimentional movement for achieving perfect verticality and fixing structural glazingsystem rigidly to the RCC/ masonry/structural steel framework of building structureusing stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetalliccontacts with nuts and washers etc. of stainless steel grade 316, of the requiredcapacity and in required numbers.c) Providing and filling, two part pump filled, structural silicone sealant and onepart weather silicone sealant compatible with the structural silicone sealant ofrequired bite size in a clean and controlled factory / work shop environment ,including double sided spacer tape, setting blocks and backer rod, all of approvedgrade, brand and manufacture, as per the approved sealant design, within and allaround the perimeter for holding glass.d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thickand of sizes, shapes and profiles, as required as per the site conditions, to seal thegap between the building structure and all its interfaces with curtain glazing tomake it watertight.e) Making provision for drainage of moisture/ water that enters the curtain glazingsystem to make it watertight, by incorporating principles of pressure equalization,providing suitable gutter profiles at bottom (if required), making necessary holesof required sizes and of required numbers etc. complete. This item includes costof all inputs of designing, labour for fabricating and installation of aluminium grid,installation of glazed units, T&P, scaffolding and other incidental charges includingwastages etc., enabling temporary structures and services, cranes or cradles etc.as described above and as specified.( complete specification as detailed in Part C - Schedule of Quantities)
25.3 : Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel unitsof size and shape as required and specified, comprising of an outer heatstrengthened float glass 6mm thick, of approved colour and shade with reflectivesoft coating on surface # 2 of approved colour and shade, an inner Heat strengthnedclear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primaryseal and secondary seal (structural silicone sealant) etc. all complete for the requiredperformances, as per the Architectural drawings, as per the approved shopdrawings, as specified and as directed by the Engineer-in-Charge. The IGUs shallbe assembled in the factory/ workshop of the glass processor. For payment,only the actual area of glass on face # 1 of the glass panels (excluding the areas ofthe grooves and weather silicone sealant) provided and fixed in position, shall bemeasured in sqm.(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating onface # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved makehaving properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflectioninternal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25-0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performanceglass shall be decided by technical sanctioning authority as per the site requirement
25.4 : Extra for openable side / top hung vision glass panels (IGUs) including providingand supplying at site all accessories and hardwares for the openable panels asspecified and of the approved make such as heavy duty stainless steel frictionhinges, min 4 -point cremone locking sets with stainless steel plates, handles,buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts,washers etc. all complete as per the Architectural drawings, as per the approvedshop drawings, as specified and as directed by the Engineer-in-Charge.
21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)
21.1.2.2 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)
21.2.2 : Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides
21.3.1 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness
21.3.2 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness
21.4.1 : Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS: 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors including cost of cutting floors, embeding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer -in- Charge.With stainless steel cover plate minimum 1.25 mm thickness
21.11.2 : Providing and fixing stainless steel (SS 304 grade) adjustable friction window stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer - in-Charge complete.255 x 19 mm
9.84 : Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
9.121 : Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross- section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminated shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.
9.122.1 : Providing and fixing to existing door frames.30 mm thick Glas Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS : 14856, including fixing to frames.
21.13 : Providing and fixing 100 mm brass locks ( best make of approved quality ) for aluminium doors including necessary cutting and making good etc. complete
21.15.2 : Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary necessary screws etc. complete.Powder coated minimum thickness 50 micron aluminium
9.97.1 : Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:300x10 mm
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm
21.18 : Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock and stopper etc to be paid separately)
Providing and fixing Stainless steel D type glass door handle with SSS polished finish of 25mmx450mm size.
Providing and fixing Stainless Steel Corner Patch Lock with Strike Plate of SSS finish for toughened glass door including all necessary fittings. Or equivalent.
9.108.2 : Providing and fixing PTMT Tower Bolts with 12 mm one piece rod inside and necessary screws etc., complete.202x42x18 mm weighing not less than 78 gms
9.106.2 : Providing and fixing PTMT handles with necessary screws etc. complete.150x34x24 mm weighing not less than 26 gms
9.88 : Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.
9.101.1 : Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Single rubber stopper
9.101.2 : Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper
9.100.1 : Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:125 mm
9.100.2 : Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:100 mm
Providing and fixing in position frameless fixed glazing using 10mm toughened glass fitted with patch fittings of approved brand or manufacture as detailed in the draiwng of specified size including supplying and fixng necessary holdfats, screws for fixing cleats, toughened glass with all labour and materials complete as per drawings and as directed.
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item) With Toughened glass 10 mm thickness
Steel Work
9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc
13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work
13.85.2 : Applying priming coats with primer of approved brand and manufacture, having low VOC ( Volatile Organic Compound) content.With ready mixed red oxide zinc chromatic on steel / iron works having VOC content less than 250 grams/ litre
10.16.2 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes
10.5.1 : Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angels 40x40x6 mm for diagonal braces
10.25.1 : Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In stringers, treads,landings etc. of stair cases, including use of chequered plate wherever required, all complete
10.25.2 : Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
10.6.2 : Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.20 mm M.S. laths with 1.20 mm thick top cover
10.7 : Providing and fixing ball bearing for rolling shutters.
10.9 : Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer -in-Charges, (area of grill to be measured).
10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)
Flooring and Waterproofing Work
16.75 : Providing and laying C.C pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator, vacuum dewatering process and finally finished by floating brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge ( The panel shuttering work shall be paid for separately)
13.52.2 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work
11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.
11.46.2 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600 x 600 mm
Providing and laying Vitrified step tiles indifferent sizes and in single piece (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.
Providing and fixing I st quality ceramic glazed wall tiles of size 600x600 conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.(Note - Basic Price of tile - Rs 380/sqm Any savings/reduction in basic price shall be accounted in the bill on pro rata basis)
Extra for using or fixing glazed/ Ceramic/ Vitrified wall tiles with cement based high polymer modified quick-set tile adhesive ( Water based) conforming to IS : 15477, in average 3 mm thickness.
8.12 : Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvillinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-charge.a. Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, lift facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm
8.3.2 : Providing edge moulding to 18 mm thick granite stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Granite work
8.13.1 : Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye orequivalent.
22.14.1 : Grading roof for water proofing treatment with:Cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
22.23.1 : Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin- charge. The product performance shall carry guarantee for 10 years against any leakage.For vertical surface two coats @0.70 kg per sqm
22.23.2 : Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin- charge. The product performance shall carry guarantee for 10 years against any leakage.For horizontal surface one coat @1.10 kg per sqm.
22.5 : Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.
11.3.1 : Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate)finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate
Specialized items
Frosted film - Supply and installation of 3M make frosted film pattern throughout all the internal glass panels wherever required of approx. 1.5 m height as per the approved pattern.
Coloured graphics pattern - Supply and installation of coloured graphics pattern / instructions / images etc over fixed glass panels / doors of approx. 1.5 m height as per the approved pattern.
Providing and fixing in position 25mm to 30 mm thick bitumen impregnated fibre board conforming to IS: 1838, including cost of primer, sealing compound in expansion joints between Beams, Slabs and Columns at all level
5.29.2.1 : Providing and fixing sheet covering over expansion joints with iron screws as per design.Aluminium fluted strips 3.15 mm thick 150 mm wide
Labour material and supervision charges for filling 25 mm baker road and PU sealant, providing synthetic expansion tape-Mapei band Tape 170 or equivalent on floor using Adesilex PG 2 of Mapei(in 1:3 ratio) or equivalent and filling PU sealant upto floor finish level and provide Aluminium 3.15 mm thick strips- 200 mm wide All complete as per manufacture specification.
9.105.3 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.66 mm overall thickness Partition with 8 mm thick double skin Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process with Compressive Strength 225 kg/sq cm, Bending Strength 100 kg/sq cm
12.62 : Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 49 Kg/m3, 50mm thick, wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rowel plug & washers and held and in position by criss crossing GI wire etc. complete as per directions of Engineer-in-charge.
False Ceiling Work
12.52.1 : Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge.GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending
12.52.2 : Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge.GI Metal Ceiling Lay in perforated Tegular global white color tiles of size 595x595 mm and 0.5mm thick with 8 mm drop; made of GI sheet having glavanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient) of 0.5, electro statically polyster powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.
Aluminium Non perforated false ceiling - Providing & Fixing true horizontal level swing down suspended ceiling comprising of approved make Aluminum Clip in Swing Down with double pip self-leveling feature and special tabs to allow swing down of tile to enable plenum access with plain visual consisting of 600X600 mm clip in plain tiles of 0.7mm uniform thickness Aluminum with bevel edge in approved color precoated with primer coat at the rear side with Light Reflectance > 60%.Tiles should have fire performance of Class A2-s1.d0 as per EN13501.The grade of aluminium shall mandatorily be AA 3003. The AluminiumTile shall mandatorily be RoHS Compliant (Resistance of Hazardous Substance).Compliant certificate shall be provided on demand. The tile shall maintain uniform Thickness of 0.7mm across all areas of tiles with no deviation. The tile shall have paint thickness of 25 microns to enable better scratch resistance.The tile shall have the ability to combine the main light with extra illumination providing 77% light reflectance & enables to achieve light uniformity. The tile shall have g Ceiling Attenuation Class of 44db. It shall withstands upto 150 Scrub cycle using Scrubablity tester as per ASTM D 2486. The tile shall offer superior wash performance without compromising panel finish integrity using a washablity tester as per ASTM D 4828. Installation: To comprise 3000mm long 'C' channels spaced at 1200mm centers securely fixed to the structural soffit by support clamp & approved hangers. The last hanger at the end of each C channel should not be greater than 600mm from the adjacent wall. Use a C-channel connector for splicing two pieces of C-channels. 4000mm spring tee bars shall be spaced at 600mm centers in a direction perpendicular to the C-channels and shall be secured at every intersection with C channel using a tee bar hanger. Use T bar connector to splice two pieces of spring tee bars. Tiles should be clipped in between two spring tee bars from below. This is a downward installation. All full panels can be removed and reinstalled without movement up into the plenum area. Perimeter trims of approved color secured to walls at 450mm maximum centers. Cut tiles to be secured to the wall angles using a spring clamp. The installation shall be undertaken as per the manufacturer's installation instructions and as directed by the Engineer-in-Charge.
Stainless Steel false ceiling - Providing and fixing in position stainless steel false ceiling of approx size 600 x 600 x 20mm with ceiling made of 1 mm thick stainless steel sheets of AISI 304 grade, visible side having satin/matt finish and coated with protective PVC taping.The joints of the stainless steel wall panels shall be made seamless, and homogeneous.There shall not be any sharp edges and all corners should be curved to avoid bacteria/fungal contamination.The Ceiling panels shall be supported to the slab with stainless steels brackets, fixtures and using nonferrous hard ware. The ceiling panel design and construction shall be provided with openings required for later inclusion of additional equipments, repair of installed equipments, without affecting the rigidity and strength of the structure. The joints between walls and ceiling(skirting) panels shall be connected by curved panels at a radius of 450mm. All provisions shall be in the Operation theatre ceiling for mounting other equipment i.e. Ceiling-mounted Operation theatre light, Pendants, Brackets for monitors, Cameras etc. complete. The rate shall also be inclusive of all materials, labour, transportation etc. complete.
Finishes
13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to floor V level; 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size)
13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer
13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work
5.23 : Smooth finishing of the exposed surface of RCC work with 6mm thick cement mortar 1:3 ( cement : 3 fine sand).
5.30 : Add for plaster drip course / groove in plastered surface or moulding to R.C.C. projections.
13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)
13.5.1 : 15 mm cement plaster on rough side of single or half brick wall of mix:1:4 ( 1 Cement : 4 coarse sand)
13.7.2 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:4 ( 1 cement : 4 fine sand)
13.22 : Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.
13.45.1 : Finishing walls with textured exterior pint of required shade:New work (Two or more coats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm
13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
22.26 : Providing and applying of swellable type water stop tape, 19mm x 25mm thick inlinear meter (expansive nature) for construction joints treatment of RCC structuresuch as raft slab, retaining walls, water storage tank and at the junctions of raftslab with the retaining walls etc.. After cleaning the surface, one coat of requiredprimer for swellable water stop tape shall be applied throughout the length of thejoint @3.78 litre per 240 running meter. Over the primed surface swellable typewater stop tape shall be placed. The work shall be carried out all complete as perspecification and the direction of the engineer-in-charge. The product performanceshall carry guarantee for 10 years against any leakage.
Roofing
Poly carbonate sheet roofing -Supply and installation of 2mm thick Poly-carbonate sheet roofing of approved make, embossed clear with UV protection coating/treatment and weight not less than 2400 gms/ sqm. It shall be fire retardant and confirming to IS 14443. the rate shall include aluminium leak proofing and fixing management system with EPDM rubber gaskets, silicone sealant etc. complete as required and as per the direction of engineer in chargeexcluding purlins, rafters and trusses and including cutting to size and shape wherever required.
12.50 : Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
12.7.1 : Providing and fixing 15cm wide, 45 cm overall semi circular plain G.S. sheet gutter with iron brackets 40x3 mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete.0.80 mm thick with zinc coating not less than 275 gm/m2
External Work
15.3 : Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.
15.60 : Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved
15.9.2 : Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In cement mortar
15.7.4 : Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar
Tree Cutting and Other External Work
2.33.1 : Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.Beyound 30 cm girth up to and including 60 cm girth
2.33.2 : Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.Beyound 60 cm girth up to and including 120 cm girth
2.33.3 : Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.Beyond 120 cm girth up to and including 240 cm girth
2.33.4 : Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.Above 240 cm girth
2.31 : Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared
2.10.1.3 : Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm
19.35.1 : Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.450 mm dia RCC pipes.
19.35.2 : Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.600 mm dia RCC pipes.
7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)
13.33.1 : Pointing on stone work with cement mortar 1:3 ( 1 cement : 3 fine sand):Flush/ Ruled pointing
16.1 : Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.
16.78.1 : Construction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.With Material conforming to Grade - I ( size range 75 mm to 0.075 mm) having CBR Value- 30
Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.
Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-40 grade with approved color design and pattern.
16.90 : Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.
16.69 : Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). ( Precast C.C. kerb stone shall be approved by Engineer-in-Charge)
Site Clearence
2.4.A.1 : Uprooting and Removing Stumps & RootsUprooting and Removing Stumps & roots, compaction of backfilling and stacking of servicable material by manual means as per Technical Specification Clause 201.A.Lead upto 100 m(i)Girth above 300 mm to 600 mm
2.4.A.2 : Uprooting and Removing Stumps & RootsUprooting and Removing Stumps & roots, compaction of backfilling and stacking of servicable material by manual means as per Technical Specification Clause 201.A. Lead upto 100 m (ii)Girth above 600 mm to 900 mm
2.4.A.3 : Uprooting and Removing Stumps & RootsUprooting and Removing Stumps & roots, compaction of backfilling and stacking of servicable material by manual means as per Technical Specification Clause 201.A. Lead upto 100 m (iii)Girth above 900 mm to 1800 mm
2.4.A.4 : Uprooting and Removing Stumps & RootsUprooting and Removing Stumps & roots, compaction of backfilling and stacking of servicable material by manual means as per Technical Specification Clause 201.A. Lead upto 100 m (iv)Girth above 1800 mm to 2700 mm
2.4.A.5 : Uprooting and Removing Stumps & RootsUprooting and Removing Stumps & roots, compaction of backfilling and stacking of servicable material by manual means as per Technical Specification Clause 201.A. Lead upto 100 m (v)Girth above 2700 mm to 4500 mm
Wall guard and corner guard
Supply and installation of Wall Guards cum hand rails with the following specification. The wall Guards shall be of height 140mm with an outer cover made out of PVC,PP/ABS with an interior core of high quality aluminium design with anti corrosive strips. The wall guards shall be fitted to the tile surface with adequate fasteners and anchor screws and braces. The thickness of vinyl and aluminium shall be 1.5mm.The surface texture shall be fire resistant . The units shall be of approved make and colour. Wall Guard cum hand rails.
Supply and installation of Brace for wall guards with the following specification. The Brace shall be made out of PVC with a thickness of 1.5mm. The Brace shall be provided at an interval of 500mm. The Brace shall be of approved make and colour. This item shall be a part of Item No. 16.01
Supply and installation of Elbow for wall guards with the following specification. The elbow shall be of height 140mm which shall be provided at the corners. The Outer Cover shall be made out of PVC,PP/ABS with an interior core of high quality aluminium design with anti corrosive strips. The thickness of vinyl and aluminium shall be 1.5mm. The surface texture shall be fire resistant . The units shall be of approved make and colour. This item shall be a part of Item No. 16.01
Supply and installation of Wall Guard with the following specification. The wall Guards shall be of height 100mm with an outer cover made out of PVC,PP/ABS with an interior core of high quality aluminium design with anti corrosive strips. The wall guards shall be fitted to the tile surface with adequate fasteners and anchor screws and braces. The thickness of vinyl and aluminium shall be 1.5mm.The surface texture shall be fire resistant. The units shall be of approved make and colour. Wall Guard
Supply and installation of End cap for Wall Guards with the following specification. The end cap for wall Guards shall be of height 100mm with an outer cover made out of PVC,PP/ABS. The End cap shall be fitted to the at every termination of wall guards. The surface texture shall be fire resistant. The units shall be of approved make and colour. End Cap
Supply and installation of corner guards made ourt of Stainless Steel 304 Grade material of thickness 1mm with an inside rubber backup of thickness 1.5mm of approved make and shall be fitted to the corner of the wall to the finished wall tile using anchor screws.. Each corner guard shall be of dimension 35mmx35mmx1500mm(H) and of approved make.
FIre door
9.161 : Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontalside & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mmthick GI sheet ( Zinc coating not less than 120gm/m2) suitable for mounting 120min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineralwool Insulation having density min 96Kg/m2 . The frame will have a provision ofG.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style ofsize M10 x 80 ) suitable for fixing in the opening along with Factory madeTemplate for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire ratedglazed shutter . The frame shall be finished with a approved fire resistant primeror Powder coating of not less than 30 micron in desired shade as per thedirections of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded
9.162 : Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 minFire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certifiedas per laboratory approved by Engineer-in-charge, with suitable mounting ondoor frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mmwide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet(zinc coating not less than 120gm/m²) duly filled mineral wool insulation havingdensity min 96 kg/m³ and fixing with necessary stainless steel ball bearing hingesof size 100x89x3mm of approved make, including applying a coat of approvedfire resistant primer or powder coating not less than 30 micron etc all completeas per direction of Engineer-in-charge (panelling to be paid for seperately
9.24.1 : Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded ) (overall area of door shutter to be measured):Rectangular or square
9.139 : Providing and fixing panic bar / latch (Double point ) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer -in-charge, all complete.
9.165.1 : Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm
9.126.2 : Providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows ( area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled and glazed shutters 25 mm to 40 mm thick.Fire retardant plywood conforming to IS : 5509
PUBLIC HEALTH ENGINEERING SYSTEM - SANITARY FIXTURES
Providing and fixing White Vitreous China Extended Wall Mounted EWC, Complete Set with 3/6 LPF Dual Cistern, overall size 765 x 370 x 650mm. or as per approved model and shape, including Cistern Fittings, Soft Close Seat Cover, bolts, nuts, washers, expansion/ rawl sleeves, gasket etc. complete, and fixing to wall, as per manufacturer's instruction and to the approval of Engineer-in-charge. Model Hindware 20096/21056 or equivalent
Providing and fixing sanitary fixtures for handicapped toilet including one number Extended wall mount closet with soft close seat cover and cistern one wash basin, one pair mounting brackets,one number elbow operated pillar cock and all other related fittings like waste coupling one number hinged rail 76 cm & 4 nos. of grab rails 60cm etc designed for people with special needs comes with as per manufactures specification including cutting and making good the walls and floors wherever required as per drawing and as directed by Engineer in charge. Model Hindware 20096/21056, 10087, F280001MD, 510880, 501894, & Parryware T9911A1 or equivalent
Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests
Supplying, installing, testing & commissioning at site in position white / colour vitreous china wash basin (480x365x205mm) with C.I./MS brackets painted white, C.P brass waste coupling of standard pattern, 32mm dia C.P, basin Pillarcock with aerator, including cutting & making good the walls wherever required complete. Wash basin below counter type with aerator PillarCock. Model - Kerovit KS207, Kerovit KB111001, Parryware T9911A1, Or Equivalent.
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Angle back wash basin size 600x480 mm with single 15 mm C.P. brass pillar tap
Providing and fixing White vitreous china Laboratory Sink with C.I brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required; all as per manufacturer's instruction and the direction of Engineer-in-charge. Size: 600 x450 x 20mm. Deep
Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.
Providing and fixing stone slab with table rubbed, edges rounded and polished,of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shade
Hot & cold CP aerator wall mixer unit - Providing, Fixing, testing and commissioning Of Hot & cold CP wall mixer unit with long bend pipe for overhead shower with all accessories. Model Parryware T4616A1 or equivalent
Supplying and fixing CP Towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.
Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.
Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.
Supplying and fixing Stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.
Supplying, installing, testing & commissioning at site in position Heavy Duty Flexible Braided Connectors, 15mm. nominal bore, 450mm. Long with higher thermal stability for cold and hot water, for Geyser points of approved quality.
Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length:15 mm nominal bore
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm
Providing and fixing Stainless Steel A ISI 304 (18/8) Kitchen Sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, waste coupling including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink without drain board 610x510 mm bowl depth 200 mm
Providing, fixing, testing, and commissioning at site Kitchen Sink Cock with aerator, Wall Mounted Type 15mm. nominal bore, overall dimensions: 208x237mm, including all necessary accessories, all as per manufacturer's instruction and to the approval of the Engineer-in-charge. Model Kerovit KB111025 or equivalent.
Providing, fixing, testing, and commissioning at site Single Lever Surgical Purpose Elbow Action Sink Mixer (Wall Mounted)with aerator Extended Operating Lever, Connecting legs & wall flanges, 15mm. nominal bore, including all necessary accessories, all as per manufacturer's instruction and to the approval of the Engineer-in-charge. Model: Jaquar FLR-CHR-5166
Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore
Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :100 mm diameter
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore
Providing and fixing toilet paper holder :C.P. brass
Supplying, installing, testing & commissioning at site in position Grab Bar up to 600mm complete.
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.
C. P. Robe Hook,60mm. Dia. x 45mm. High. Model: Cera F5003108SS or equivalent
Providing,fixing testing and commissioning Energy Efficient Storage Type Electric Water Heater, 2kw each, as per specification Capacity 15 Ltrs
Providing,fixing testing and commissioning Energy Efficient Storage Type Electric Water Heater, 2kw each, as per specification Capacity 25 Ltrs
Providing,fixing testing and commissioning Energy Efficient Storage Type Electric Water Heater, 2kw each, as per specification Capacity 35 Ltrs
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40 mm dia
Providing,fixing testing and commissioning 1½"x 40x300 Plastic P Trap (P Trap) for Sink. Adjusting pipe 120mm, drain elbow 220mm.
INTERNAL DRAINAGE
Supplying, Installing, Testing & Commissioning at site in position uPVC pipe (SWR) of Type B (IS:13592) including injection moulded fittings with bosses where required eg 90 Degree, 45 Degree bends, Y, couplings, adapters,rodding eye & clamping with Universal clamps, Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete; and jointing with approved adhesive by manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site (For Soil & Waste pipes -Internal). 110mm OD
Supplying, Installing, Testing & Commissioning at site in position uPVC pipe (SWR) of Type B (IS:13592) including injection moulded fittings with bosses where required eg 90 Degree, 45 Degree bends, Y, couplings, adapters, rodding eye & clamping with Universal clamps, Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete; and jointing with approved adhesive by manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site (For Soil & Waste pipes -Internal). 75mm OD
Supplying, Installing, Testing & Commissioning at site in position uPVC pipe of 6Kg/sq.cm (IS:4985) including injection moulded fittings with bosses where required eg 90 Degree bend, 45 Degree bends, 'Y', couplings, adapters & clamping with Universal clamps/U bolt 1metre spacing, Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete; and jointing with approved adhesive by manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site (For Soil & Waste pipes -Internal). 63 mm (IS 4985,6kgf/cm2)
Supplying, Installing, Testing & Commissioning at site in position uPVC pipe of 6Kg/sq.cm (IS:4985) including injection moulded fittings with bosses where required eg 90 Degree bend, 45 Degree bends, 'Y', couplings, adapters & clamping with Universal clamps/U bolt 1metre spacing, Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete; and jointing with approved adhesive by manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site (For Soil & Waste pipes -Internal). 50 mm (IS 4985,6kgf/cm2)
Supplying, Installing, Testing & Commissioning at site in position uPVC pipe of 6Kg/sq.cm (IS:4985) including injection moulded fittings with bosses where required eg 90 Degree bend, 45 Degree bends, 'Y', couplings, adapters & clamping with Universal clamps 1metre spacing, Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete; and jointing with approved adhesive by manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site (For Soil & Waste pipes -Internal). 40 mm (IS 4985,6kgf/cm2)
Supplying, Installing, Testing & Commissioning at site in position uPVC pipe of 10Kg/sq.cm (IS:4985) including injection moulded fittings with bosses where required eg 90 Degree bend, 45 Degree bends, 'Y', couplings, adapters & clamping with Universal clamps 1metre spacing, Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete; and jointing with approved adhesive by manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site 32 mm OD (10kg/cm2)- for sunken drain
Supplying, Installing, Testing & Commissioning at site in position uPVC pipe (SWR) of Type A (IS:13592) including injection moulded fittings with bosses where required eg 90 Degree, 45 Degree bends, Y, couplings, adapters,rodding eye & clamping with Universal clamps, Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete; and jointing with approved adhesive by manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site (For Vent pipes -Internal). 75mm OD
Supplying, Installing, Testing & Commissioning at site in position uPVC pipe (SWR) of 4kg/cm2 (IS:4985)including injection moulded fittings with bosses where required eg 90 Degree, 45 Degree bends, Y, couplings, adapters,rodding eye & clamping with Universal clamps, Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete; and jointing with approved adhesive by manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site (For Vent pipes -Internal). 63mm OD
Supplying, Installing, Testing & Commissioning at site in position uPVC pipe (SWR) of 6kg/cm2 (IS:4985)including injection moulded fittings with bosses where required eg 90 Degree, 45 Degree bends, Y, couplings, adapters,rodding eye & clamping with Universal clamps, Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete; and jointing with approved adhesive by manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site (For Vent pipes -Internal). 50mm OD
Supplying, Installing, Testing & Commissioning at site in position Ring uPVC pipe (SWR) of Type B(IS:13592) including SWR jointing with Rubber Ring Seal (IS 5382) PVC Moulded (IS 14735 )fittings with bosses where required eg.Door tees, Door bends, 'Y', bends, clamps, couplings, adapters, rodding eye and cowls with sealing grooves and clamping with Position, including cutting and making good the walls and floors as required at site (For Vertical & Horizontal Shaft piping). Core Cutting in RCC Structure shall measured separately. Clamping details - For Vertical Shafts G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 / 2.5 mm thick) , Rail Leg 2 1/2 ''STD Powder Coated Clamping details - For Suspended lines G.I. "U" bolts (8 mm thick) on Heavy Duty G.I.slotted rails(2.5 mm thick) or Clamping with Universal clamps, Anchor fastners(10mm), Threaded Rod(10mm), nuts, washers etc complete. 160mm OD
Supplying, Installing, Testing & Commissioning at site in position Ring uPVC pipe (SWR) of Type B(IS:13592) including SWR jointing with Rubber Ring Seal (IS 5382) PVC Moulded (IS 14735 )fittings with bosses where required eg.Door tees, Door bends, 'Y', bends, clamps, couplings, adapters, rodding eye and cowls with sealing grooves and clamping with Position, including cutting and making good the walls and floors as required at site (For Vertical & Horizontal Shaft piping). Core Cutting in RCC Structure shall measured separately. Clamping details - For Vertical Shafts G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 / 2.5 mm thick) , Rail Leg 2 1/2 ''STD Powder Coated Clamping details - For Suspended lines G.I. "U" bolts (8 mm thick) on Heavy Duty G.I.slotted rails(2.5 mm thick) or Clamping with Universal clamps, Anchor fastners(10mm), Threaded Rod(10mm), nuts, washers etc complete. 110mm OD
Supplying, Installing, Testing & Commissioning at site in position Ring uPVC pipe (SWR) of Type B(IS:13592) including SWR jointing with Rubber Ring Seal (IS 5382) PVC Moulded (IS 14735 )fittings with bosses where required eg.Door tees, Door bends, 'Y', bends, clamps, couplings, adapters, rodding eye and cowls with sealing grooves and clamping with Position, including cutting and making good the walls and floors as required at site (For Vertical & Horizontal Shaft piping). Core Cutting in RCC Structure shall measured separately. Clamping details - For Vertical Shafts G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 / 2.5 mm thick) , Rail Leg 2 1/2 ''STD Powder Coated Clamping details - For Suspended lines G.I. "U" bolts (8 mm thick) on Heavy Duty G.I.slotted rails(2.5 mm thick) or Clamping with Universal clamps, Anchor fastners(10mm), Threaded Rod(10mm), nuts, washers etc complete. 75mm OD
Supplying, Installing, Testing & Commissioning at site in position Ring uPVC pipe (SWR) of Type A(IS:13592) including SWR jointing with Rubber Ring Seal (IS 5382) PVC Moulded (IS 14735 )fittings with bosses where required eg.Door tees, Door bends, 'Y', bends, clamps, couplings, adapters, rodding eye and cowls with sealing grooves and clamping with Position, including cutting and making good the walls and floors as required at site (For Vertical & Horizontal Shaft piping for rainwater/Vent). Clamping details - For Vertical Shafts G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 / 2.5 mm thick) , Rail Leg 2 1/2 ''STD Powder Coated Clamping details - For Suspended lines G.I. "U" bolts (8 mm thick) on Heavy Duty G.I.slotted rails(2.5 mm thick) or Clamping with Universal clamps, Anchor fastners(10mm), Threaded Rod(10mm), nuts, washers etc complete. 160mm OD
Supplying, Installing, Testing & Commissioning at site in position Ring uPVC pipe (SWR) of Type A(IS:13592) including SWR jointing with Rubber Ring Seal (IS 5382) PVC Moulded (IS 14735 )fittings with bosses where required eg.Door tees, Door bends, 'Y', bends, clamps, couplings, adapters, rodding eye and cowls with sealing grooves and clamping with Position, including cutting and making good the walls and floors as required at site (For Vertical & Horizontal Shaft piping for rainwater/Vent). Clamping details - For Vertical Shafts G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 / 2.5 mm thick) , Rail Leg 2 1/2 ''STD Powder Coated Clamping details - For Suspended lines G.I. "U" bolts (8 mm thick) on Heavy Duty G.I.slotted rails(2.5 mm thick) or Clamping with Universal clamps, Anchor fastners(10mm), Threaded Rod(10mm), nuts, washers etc complete. 110mm OD
Supplying, Installing, Testing & Commissioning at site in position Ring uPVC pipe (SWR) of Type A(IS:13592) including SWR jointing with Rubber Ring Seal (IS 5382) PVC Moulded (IS 14735 )fittings with bosses where required eg.Door tees, Door bends, 'Y', bends, clamps, couplings, adapters, rodding eye and cowls with sealing grooves and clamping with Position, including cutting and making good the walls and floors as required at site (For Vertical & Horizontal Shaft piping for rainwater/Vent). Clamping details - For Vertical Shafts G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 / 2.5 mm thick) , Rail Leg 2 1/2 ''STD Powder Coated Clamping details - For Suspended lines G.I. "U" bolts (8 mm thick) on Heavy Duty G.I.slotted rails(2.5 mm thick) or Clamping with Universal clamps, Anchor fastners(10mm), Threaded Rod(10mm), nuts, washers etc complete. 75mm OD
Supplying, Installing, Testing & Commissioning at site in position Ring uPVC pipe (SWR) of 4kg/cm2 (IS:4985)) including jointing PVC Moulded (IS 14735 )fittings with bosses where required eg.Door tees, Door bends, 'Y', bends, clamps, couplings, adapters, rodding eye and cowls with sealing grooves and clamping with Position, including cutting and making good the walls and floors as required at site (For Vertical & Horizontal Shaft piping for rainwater/Vent). Clamping details - For Vertical Shafts G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 / 2.5 mm thick) , Rail Leg 2 1/2 ''STD Powder Coated Clamping details - For Suspended lines G.I. "U" bolts (8 mm thick) on Heavy Duty G.I.slotted rails(2.5 mm thick) or Clamping with Universal clamps, Anchor fastners(10mm), Threaded Rod(10mm), nuts, washers etc complete. 63 mm OD(4kg/cm2)
Deep Seal uPVC fabricated Multi floor trap - Providing, Fixing, testing and commissioning at site in position Deep Seal (7”) uPVC Fabricated Multi Floor Trap, with suitable supporting on GI slotted rails (1.6mmthick) full threaded rod, Anchor fasteners etc. complete in all respects - 50/75 mm dia inlet/outlet (In Ceiling)
uPVC fabricated Multi floor trap - Providing, Fixing, testing and commissioning at site in position uPVC Fabricated Multi Floor Trap, with thrust block support including complete cost o cutting chases and making good the walls in all respects - 50/75 mm dia inlet/outlet (In Sunken)
Supplying, installing, testing & commissioning at site in position 110mm dia deep seal PVC P Trap with boss tee and access cap including all necessary fittings and supports complete.
C.P. cast brass or stainless steel Square Flat cut lock anti cockroach grating cover - Providing and Fixing Heavy Duty Stainless Steel Square Flat cut lock anti Cockroach Trap Stainless Steel A ISI 304 with 153x153mm. Grating, for 110mm. Floor Traps.
Heavyduty stainless steel cover for Concealed Floor Trap for Urinal - Providing and Fixing 153x153mm dia Heavyduty stainless steel cover for Concealed Floor Trap ISI 304 Cover, for Urinal.
Heavyduty stainless steel cleanout cover - Providing and Fixing Heavy Duty Stainless Steel A ISI 304 Clean out Cover, sealed, threaded covers, including suitable insert keys for opening, if required.
Providing and fixing soil, waste and vent pipes : 100mm dia Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905
Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100 mm dia Hubless centrifugally cast (spun) iron epoxy coated inside & outside asper IS:15905
Providing and fixing plain bend of required degree. 100 mm dia Hubless centrifugally cast (spun) iron pipes epoxy coated inside &outside IS:15905
Providing and fixing double equal plain junction of required degree. 100x100x100x100 mm Hubless centrifugally cast (spun) iron pipes epoxy coated inside &outside IS:15905
Providing and fixing single equal plain junction of required degree: 100x100x100 mm Hubless centrifugally cast (spun) iron epoxy coated inside & outsideas per IS:15905
Providing and fixing double equal plain invert branch of required degree: 100x100x100x100 mm Hubless centrifugally cast (spun) iron epoxy coated inside & outside as perIS:15905
Providing and fixing single equal plain invert branch of required degree: 100x100x100 mm Hubless centrifugally cast (spun) iron epoxy coated inside & outside as perIS:15905
Providing and fixing terminal guard: 100 mm Hubless centrifugally cast (spun) iron epoxy coated inside & outside as perIS:15905
Providing and fixing trap of self cleansing design with screwed down or hinged grating without vent arm complete, including cost of cutting and making good the walls and floors: 100 mm inlet and 100 mm outlet Hubless centrifugally cast (spun) iron epoxy coated inside & outside as perIS:15905
Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe 100 mm dia SS 304 grade coupling with EPDM rubber gasket
Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.
WATER SUPPLY
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia. Pipes.
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia. Pipes.
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia. Pipes.
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 15 mm nominal outer dia. Pipes.
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with Universal clamps/U bolt at 1.00 m spacing,Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 20 mm nominal outer dia. Pipes.
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with Universal clamps/U bolt at 1.00 m spacing,Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 25 mm nominal outer dia. Pipes.
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with Universal clamps/U bolt at 1.00 m spacing,Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 32 mm nominal outer dia. Pipes.
Providing and fixing uPVC Pipes, Sch. 40 (ASTM D 1785) and with Sch. 40 (ASTM D 2466) Fittings, fixing the pipe with Universal clamps/U bolt at 1.00 m spacing,Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. This includes jointing of pipes & fittings with one step uPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - Ceiling and Shaft 15 mm nominal outer dia. Pipes.
Providing and fixing uPVC Pipes, Sch. 40 (ASTM D 1785) and with Sch. 40 (ASTM D 2466) Fittings, fixing the pipe with Universal clamps/U bolt at 1.00 m spacing,Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. This includes jointing of pipes & fittings with one step uPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - Ceiling and Shaft 20 mm nominal outer dia. Pipes.
Providing and fixing uPVC Pipes, Sch. 40 (ASTM D 1785) and with Sch. 40 (ASTM D 2466) Fittings, fixing the pipe with Universal clamps/U bolt at 1.00 m spacing,Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. This includes jointing of pipes & fittings with one step uPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - Ceiling and Shaft 25 mm nominal outer dia. Pipes.
Providing and fixing uPVC Pipes, Sch. 40 (ASTM D 1785) and with Sch. 40 (ASTM D 2466) Fittings, fixing the pipe with Universal clamps/U bolt at 1.00 m spacing,Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. This includes jointing of pipes & fittings with one step uPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - Ceiling and Shaft 32 mm nominal outer dia. Pipes.
Providing and fixing uPVC Pipes, Sch. 40 (ASTM D 1785) and with Sch. 40 (ASTM D 2466) Fittings, fixing the pipe with Universal clamps/U bolt at 1.00 m spacing,Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. This includes jointing of pipes & fittings with one step uPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - Ceiling and Shaft 40 mm nominal outer dia. Pipes.
Providing and fixing uPVC Pipes, Sch. 40 (ASTM D 1785) and with Sch. 40 (ASTM D 2466) Fittings, fixing the pipe with Universal clamps/U bolt at 1.00 m spacing,Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. This includes jointing of pipes & fittings with one step uPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - Ceiling and Shaft 50 mm nominal outer dia. Pipes.
Providing and fixing uPVC Pipes, Sch. 40 (ASTM D 1785) and with Sch. 40 (ASTM D 2466) Fittings, fixing the pipe with Universal clamps/U bolt at 1.00 m spacing,Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. This includes jointing of pipes & fittings with one step uPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - Ceiling and Shaft 65 mm nominal outer dia. Pipes.
Providing and fixing uPVC Pipes, Sch. 40 (ASTM D 1785) and with Sch. 40 (ASTM D 2466) Fittings, fixing the pipe with Universal clamps/U bolt at 1.00 m spacing,Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. This includes jointing of pipes & fittings with one step uPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - Ceiling and Shaft 80 mm nominal outer dia. Pipes.
Providing and fixing uPVC Pipes, Sch. 40 (ASTM D 1785) and with Sch. 40 (ASTM D 2466) Fittings, fixing the pipe with Universal clamps/U bolt at 1.00 m spacing,Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. This includes jointing of pipes & fittings with one step uPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - Ceiling and Shaft 100 mm nominal outer dia. Pipes.
Providing and fixing uPVC Pipes, Sch. 80 (ASTM D 1785) and with Sch. 80 (ASTM D 2467) Fittings, fixing the pipe with Universal clamps/U bolt at 1.00 m spacing,Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. This includes jointing of pipes & fittings with one step uPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - Ceiling and Shaft 65 mm nominal outer dia. Pipes.
Providing and fixing uPVC Pipes, Sch. 80 (ASTM D 1785) and with Sch. 80 (ASTM D 2467) Fittings, fixing the pipe with Universal clamps/U bolt at 1.00 m spacing,Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. This includes jointing of pipes & fittings with one step uPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - Ceiling and Shaft 80 mm nominal outer dia. Pipes.
Providing and fixing uPVC Pipes, Sch. 80 (ASTM D 1785) and with Sch. 80 (ASTM D 2467) Fittings, fixing the pipe with Universal clamps/U bolt at 1.00 m spacing,Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. This includes jointing of pipes & fittings with one step uPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - Ceiling and Shaft 100 mm nominal outer dia. Pipes.
Providing and fixing uPVC Pipes, Sch. 80 (ASTM D 1785) and with Sch. 80 (ASTM D 2467) Fittings, fixing the pipe with Universal clamps/U bolt at 1.00 m spacing,Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. This includes jointing of pipes & fittings with one step uPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - Ceiling and Shaft 150 mm nominal outer dia. Pipes.
Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :15 mm nominal bore
Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :20 mm nominal bore
Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25 mm nominal bore
Providing and fixing gun metal gate valve with C.I. wheel of approved quality(screwed end) :32 mm nominal bore
Providing and fixing gun metal gate valve with C.I. wheel of approved quality(screwed end) :40 mm nominal bore
Providing and fixing gun metal gate valve with C.I. wheel of approved quality(screwed end) :50 mm nominal bore
Providing and fixing gun metal non- return valve of approved quality (screwed end) :32 mm nominal bore Horizontal
Providing and fixing gun metal non- return valve of approved quality (screwed end) : 40 mm nominal bore Horizontal
Providing and fixing gun metal non- return valve of approved quality (screwed end) : 50 mm nominal bore Horizontal
Providing and fixing gun metal non- return valve of approved quality (screwed end) : 65 mm nominal bore Horizontal
Brass Automatic Air Release Valves - Providing, Fixing, testing and commissioning at site in positions Brass Automatic Air Release Valves, of approved quality and make on the top of the vertical water supply pipes as per specification and drawing - 3/4"(20mm) dia
Supplying, Installing & Testing at site in position Brass Float valve (PN 16) of approved make with PP float & nipple with brass threaded insert, brass back nuts, piston and bolts etc complete in all respect to the satisfaction of Project Manager. 40mm dia (1 ½”)
SS ball valve 15mm dia - Providing, Fixing at site in position full way lever operated forged SS ball valve (screwed end)of brass body with forged brass hard chrome plate (PN 10) of approved make with necessary MTA fittings in position as per drawings. - ½” (15mm) dia
SS ball valve 20mm dia - Providing, Fixing at site in position full way lever operated forged SS ball valve (screwed end)of brass body with forged brass hard chrome plate (PN 10) of approved make with necessary MTA fittings in position as per drawings. - ¾” (20mm) dia
SS ball valve 25mm dia - Providing, Fixing at site in position full way lever operated forged SS ball valve (screwed end)of brass body with forged brass hard chrome plate (PN 10) of approved make with necessary MTA fittings in position as per drawings. - 1” (25mm) dia
SS ball valve 32mm dia - Providing, Fixing at site in position full way lever operated forged SS ball valve (screwed end)of brass body with forged brass hard chrome plate (PN 10) of approved make with necessary MTA fittings in position as per drawings. - 1 1/4” (32mm) dia
SS ball valve 40mm dia - Providing, Fixing at site in position full way lever operated forged SS ball valve (screwed end)of brass body with forged brass hard chrome plate (PN 10) of approved make with necessary MTA fittings in position as per drawings. - 1 1/2” (40mm) dia
SS ball valve 50mm dia - Providing, Fixing at site in position full way lever operated forged SS ball valve (screwed end)of brass body with forged brass hard chrome plate (PN 10) of approved make with necessary MTA fittings in position as per drawings. - 2” (50mm) dia
Providing and fixing C.I. Sluice Valve, PN-16, with IS: 14846 Mark, with required flanges, rubber insertions, bolts, nuts, Washers etc. complete. 100mm. PN-16
CI Butterfly valve 250mm dia (PN 10) - Providing, Fixing at site in position CI Butterfly valve (PN 10) wafer type of approved make with necessary PVC flanges, gaskets, nuts and bolts etc complete within position as per drawing - 10”(250mm) dia
Providing and Fixing Ball Type Foot Valve. PN 10, with Cast Iron Body Nitrile Reinforced Ball, Screwed End, required in the Suction Lines of for Water Transfer and Distribution Pumps.65mm.
Providing and Fixing Ball Type Foot Valve. PN 10, with Cast Iron Body Nitrile Reinforced Ball, Screwed End, required in the Suction Lines of for Water Transfer and Distribution Pumps.50mm.
Supplying, installing,Testing & commissioning at site in position Multi Jet Water meter with unions of removable mechanism type, magnetically coupled, having dry dial, hermetically sealed totaliser,retrofitable for pulse output and conforming to ISO-4064 Class B complete. Water meter 40mm
EXTERNAL SEWERAGE & STORM WATER DRAIN
Supplying, Installing & Testing of pipes and conveying to position; and jointing to true lines and gradients, PVC pipe of IS 4985(6kg/cm2), jointing the pipe line as per specification, testing the pipe line after installation to the specified hydrostatic test pressure including Supplying Installing specials like bends, couplers, sockets, connections etc. as per provisions of IS: 1742-1983 (Code of practice for building drainage) complete(excluding excavation) 200mm OD
Supplying, Installing & Testing of pipes and conveying to position; and jointing to true lines and gradients, PVC pipe of IS 4985(6kg/cm2), jointing the pipe line as per specification, testing the pipe line after installation to the specified hydrostatic test pressure including Supplying Installing specials like bends, couplers, sockets, connections etc. as per provisions of IS: 1742-1983 (Code of practice for building drainage) complete(excluding excavation) 160mm OD
Supplying, Installing & Testing of pipes and conveying to position; and jointing to true lines and gradients, PVC pipe of IS 4985(6kg/cm2), jointing the pipe line as per specification, testing the pipe line after installation to the specified hydrostatic test pressure including Supplying Installing specials like bends, couplers, sockets, connections etc. as per provisions of IS: 1742-1983 (Code of practice for building drainage) complete(excluding excavation) 110mm OD
Supplying, Installing & Testing of pipes and conveying to position; and jointing to true lines and gradients, PVC pipe of IS 4985(6kg/cm2), jointing the pipe line as per specification, testing the pipe line after installation to the specified hydrostatic test pressure including Supplying Installing specials like bends, couplers, sockets, connections etc. as per provisions of IS: 1742-1983 (Code of practice for building drainage) complete(excluding excavation) 75mm OD
Supplying, Installing & Testing of pipes and conveying to position; and jointing to true lines and gradients, PVC pipe of IS 4985(4kg/cm2), jointing the pipe line as per specification, testing the pipe line after installation to the specified hydrostatic test pressure including Supplying Installing specials like bends, couplers, sockets, connections etc. as per provisions of IS: 1742-1983 (Code of practice for rain water pipes) complete(excluding excavation) 250mm OD
Supplying, Installing & Testing of pipes and conveying to position; and jointing to true lines and gradients, PVC pipe of IS 4985(4kg/cm2), jointing the pipe line as per specification, testing the pipe line after installation to the specified hydrostatic test pressure including Supplying Installing specials like bends, couplers, sockets, connections etc. as per provisions of IS: 1742-1983 (Code of practice for rain water pipes) complete(excluding excavation) 200mm OD
Providing and fixing uPVC Pipes, Sch. 40 (ASTM D 1785) and with Sch. 40 (ASTM D 2466) Fittings, This includes jointing of pipes & fittings with one step uPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work (Including excavation) 20 mm nominal outer dia Pipes
Providing and fixing uPVC Pipes, Sch. 40 (ASTM D 1785) and with Sch. 40 (ASTM D 2466) Fittings, This includes jointing of pipes & fittings with one step uPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work (Including excavation) 25 mm nominal outer dia Pipes
Providing and fixing uPVC Pipes, Sch. 40 (ASTM D 1785) and with Sch. 40 (ASTM D 2466) Fittings, This includes jointing of pipes & fittings with one step uPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work (Including excavation) 32 mm nominal outer dia Pipes
Providing and fixing uPVC Pipes, Sch. 40 (ASTM D 1785) and with Sch. 40 (ASTM D 2466) Fittings, This includes jointing of pipes & fittings with one step uPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work (Including excavation) 40 mm nominal outer dia Pipes
Providing and fixing uPVC Pipes, Sch. 80 (ASTM D 1785) and with Sch. 80 (ASTM D 2467) Fittings, This includes jointing of pipes & fittings with one step uPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work (Including excavation) 50 mm nominal outer dia Pipes
Providing and fixing uPVC Pipes, Sch. 80 (ASTM D 1785) and with Sch. 80 (ASTM D 2466) Fittings, This includes jointing of pipes & fittings with one step uPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work (Including excavation) 65 mm nominal outer dia Pipes
Providing and fixing uPVC Pipes, Sch. 80 (ASTM D 1785) and with Sch. 80 (ASTM D 2467) Fittings, This includes jointing of pipes & fittings with one step uPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work (Including excavation) 100 mm nominal outer dia Pipes
Providing and fixing uPVC Pipes, Sch. 80 (ASTM D 1785) and with Sch. 80 (ASTM D 2467) Fittings, This includes jointing of pipes & fittings with one step uPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work (Including excavation) 80 mm nominal outer dia Pipes
Supply,installation, testing and commissioning of stainless steel coarse Screen (opening 10mm) suitable for screen chamber of size 500mmx500mm removable type including all material charges,labour transportation,loading unloading etc. Complete as per the direction of Engineer in charge.
Providing and fixing square-mouth PVC gully trap complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P type With Sewer bricks conforming to IS : 4885
Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12 mm dia steeel bar conforming to IS:1786, having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 ( 1cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) Complete as per design
Excavating trenches of required width for pipes, including excavation for sockets, depth up to 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m : In all kinds of Soil Pipes and cables not exceeding 80 mm dia.
Excavating trenches of required width for pipes, including excavation for sockets, depth up to 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m : In all kinds of Soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia
Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work : Sub analysis item for sand filling component
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size)
MISCELLANEOUS ITEMS
Supplying and fixing C.I. cover without frame for manholes :455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg
Supplying and fixing C.I. cover without frame for manholes :560 mm diameter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg
Supplying, Installing & Testing at site in position Fabricated 150mm (6")uPVC Astm Sch 80 Puddle flange in the overhead water tanks as per the drawings and the requirement of the Project Manager. - 150mm(6") uPVC Astm Sch 80 Puddle flange
Supplying, Installing & Testing at site in position Fabricated 100mm (4")uPVC Astm Sch 80 Puddle flange in the overhead water tanks as per the drawings and the requirement of the Project Manager. - 100mm(4") uPVC Astm Sch 80 Puddle flange
Supplying, Installing & Testing at site in position Fabricated 80mm (3")uPVC Astm Sch 80 Puddle flange in the overhead water tanks as per the drawings and the requirement of the Project Manager. - 80mm(3") uPVC Astm Sch 80 Puddle flange
Supplying, Installing & Testing at site in position Fabricated 65mm (2½") uPVC Astm Sch 80 Puddle flange in the overhead water tanks as per the drawings and the requirement of the Project Manager. - 65mm (2½") uPVC Astm Sch 80 Puddle flange
Supplying, Installing & Testing at site in position Fabricated 50mm (2")uPVC Astm Sch 80 Puddle flange in the overhead water tanks as per the drawings and the requirement of the Project Manager. - 50mm(2") uPVC Astm Sch 80 Puddle flange
Supplying, Installing & Testing at site in position Fabricated 40mm (1½")uPVC Astm Sch 80 Puddle flange in the overhead water tanks as per the drawings and the requirement of the Project Manager. -40mm (1½")uPVC Astm Sch 80 Puddle flange
Supplying, Installing & Testing at site in position Fabricated 32mm (1¼")uPVC Astm Sch 80 Puddle flange in the overhead water tanks as per the drawings and the requirement of the Project Manager. - 32mm 1¼"uPVC Astm Sch 80 Puddle flange
PLUMBING PUMPS & ACCCESSORIES
Vertical multi stage centrifugal pumps (surface pump) for Domestic Water Supply - Supply, Installation, Testing and Commissioning 2 nos, Vertical multi stage centrifugal pumps (surface pump) set, having SS Impeller and Shafts, CI/SS Casing, Mechanical Seal Each pumps should be capable to deliver 11 lps @ 40mtr head, Head range 15 to 55 mtrs (20 lps to 5 lps), ''F'' class Insulation, IE3 Rated Electric Motors, IP 55 Protection, Hydraulic efficiency more than 67% motor efficiency more than 85% with Wall mounting Microprocessor based common control Panel to operate the pumpset as ( 1Working + 1Standby ) Star Delta,having features of automatic pump change over in every Start/Stop, Dry run, Overload, Phase Reversal Protections etc. level controller for Auto Start/ Stop Function, Digital display,Pressure gauge, Float Switches, Auto/Manuel Operation . The total system shall be assembled and tested at factory as per the duty conditions. (For Domestic Water from sump to OHT)
Supply, Installation, Testing and Commissioning Pressure Booster Flushing Water Distribution System with Factory Assembled Packaged Pump Set, complete with 3 Vertical Multistage Inline Pumps, with S.S Impeller, Shafts, CI/SS Casing, One Working, One Assist and 1 Stand by Pumps, each of Capacity: 9M3/ Hr @ 45 Mtr. Head, each, with 3Ph, ''F'' class Insulation, IE3 Rated Electric Motors, IP 55 Protection, VFD Drive, Automatic Microprocessor Based Control Panel, Pressure Transducer Sensors, Pressure Gauges, 200Ltr. Diaphragm Pressure Vessel, Individual Suction Lines, Common Delivery Manifolds, Isolating Valves, Non Return Valves, Pressure gauge, Fittings, Accessories etc, all a on common frame. . etc, all a on common frame. The Quoted Price for the Pump Set shall be inclusive of connected Electrical Work, all as per Technical Specifications. Each Pump Shall be capable of working with Negative Suction for Pumping Raw Water from a Depth of 3.5 Mtr, The Manufacturer can decide the Pumps accordingly.
Sewage Solid handling pumps - Supply, testing and commissioning of Submersible non clog Sewage Solid handling pumps. Control Panel for Controlling 2 Pumps, having SS Shaft, Impeller, and CI/SS Casing, IP 68 Protection Each pumps should be capable to deliver 5 lps @ 10mtr head for each pump, solid handling 50mm with Wall mounting Microprocessor based common control Panel to operate the pumpset as ( 1Working + 1Standby ) having features of Cyclic Timer for Cascading Operation and Float Switch/Probe Suitable for Automatic Operation. The Panel should have the following Protection for Single Phase Prevention, Over Load Protection, Over /Under Voltage Protection, Dry Running Protection, Transient Surge Protection, with Auto/Manual Operation & Auto coupling . The Enclosure should be of IP 55 standards. The Panel should have BMS compatible thro RS 485 Communication(Modbus). (For Soil Tranfer Pump)
Sewage Solid handling pumps - Supply, testing and commissioning of Submersible non clog Sewage Solid handling pumps. Control Panel for Controlling 2 Pumps, having SS Shaft, Impeller, and CI/SS Casing, IP 68 Protection Each pumps should be capable to deliver 4 lps @ 10mtr head for each pump, solid handling 50mm with Wall mounting Microprocessor based common control Panel to operate the pumpset as ( 1Working + 1Standby ) having features of Cyclic Timer for Cascading Operation and Float Switch/Probe Suitable for Automatic Operation. The Panel should have the following Protection for Single Phase Prevention, Over Load Protection, Over /Under Voltage Protection, Dry Running Protection, Transient Surge Protection, with Auto/Manual Operation & Auto coupling . The Enclosure should be of IP 55 standards. The Panel should have BMS compatible thro RS 485 Communication(Modbus). (For Medical Waste Tranfer Pump)
FILTER FEED PUMP SET. Supply, Testing and Commission Filter Feed Pump Set, Submersible Type for Pumping Raw Water to Water Treatment Plant, 2 Pump System with One Working + 1 One Cyclically Stand by Pumps, each Pump of Capacity: 20M³/Hr. @ 45Mtr. Head, having SS Impeller, Shafts, Casing, with 3Ph, complete with Microprocessor Based Control Panel, for Auto and Cyclic Operation, with all Protection (Digital display, Low &high voltage protection, dry run, phase reversal, pump over load, etc.), Level Sensors / Float Switches in Treated Water & Raw Water Tanks and Control Cabling / Wiring between Level Sensors / Float Switches and Control Panel, Delivery Manifold, Isolating Valves, Non Return valves, Pressure Gauge, Fittings, Stainless Steel (Grade:304) Lifting Chains, Accessories etc. all as per Technical Specifications. The Control Panel shall be capable operating the pumps (starts and stops) by sensing the level difference in water in the Treated Water Tank. Also; capable of ‘not starting or stopping the running pumps', when the water in the underground Raw Water Tank goes below the pre-set minimum level. The Pumps to be installed in the Underground Raw Water Tank and Common Control Panel in the Pump Room, in Basement Floor, approx. 100 Mtr. away from Raw Water Tank. The Underground Power Cabling between Pumps and Control Panel and Control Cabling between Control Panel & Level Sensor / Float Switch, in the Underground Raw Water Tank, shall be measured as a part of Electrical Work. The Quoted Price for the Pump Set shall be inclusive of all above requirement, necessary Level Sensors / Float Switches, Power Cabling, Control Cabling etc, except what measured as a part of Electrical Work, as detailed above.
Supply, Testing and Commission Submersible Type Storm Water Transfer Dewatering Pump Set, complete set with 1 working + 1 Standby Submersible non- clog pump , Solids handling: 40mm , and with Common Control Panel for automatic operation and Manually change over facility. Capacity 12 M3/Hr. at 10 Mtrs. head, each, with Three Phase with float switches/level sensors etc. necessary control valves, Pressure Gauges fittings and accessories, for discharging rain water from collection pits in basement floor, to lower strata. The price shall inclusive of all connected electrical work as detailed in the technical specification.
WATER TREATMENT PLANT
Supply, Installation, testing and commission Water Pre-Treatment Plant Capacity: 20M3 /Hr, for continuous operation of 10 Hr, complete with High Pressure Sand Filter, Activated Carbon Filter,with Multiport valves, Chemical Dosing etc as per final requirement, connected Pipe Work etc, all as per Technical Specifications.Filter Feed Pumps shall be measured seperately.
SEWAGE TREATMENT PLANT
Supply installation, testing and commissioning of Sewage Treatment Plant of 300 KLD capacity as per specifications below. Inlet Parameter pH: 5.5–9, BOD:300-400mg/l, COD:500-800mg/l, Suspended Solids:100-250mg/l, Oil&Grease:10- 50 mg/l Outlet Parameter pH:6.5–8.5, BOD:<3mg/l, COD:<50mg/l, Suspended Solids:<20mg/l, Oil &Grease:<1 mg/l, Total Nitrogen:<10 SS Coarse Screen -1 No. Sewage Transfer Pump- 15m3/hr@ 8-10m Head- 2 nos. Diffusers for Equalization tank: Coarse Bubble, Non membrane, 90mm x 800mm. Make: Southern scogen- 10 nos PVC Anaerobic Packing media (30.24m3) with necessary supports Diffusers for Aeration Tank- Fine Bubble, EPDM, 90mm x 1000mm. Make : Southern scogen - 30 nos. MBBR media- Polyethylene with 500m2/m3- 19m3 with necessary sieves for retaining media. Airblower with motor - 400m3/hr @ 0.4 bar -2 nos. Recirculation pump - 45m3/hr @ 8m head- 2 nos. Chemical Dosing system- 0-4lph @ 5.5 kg/cm2 & 100 litres tank-4 nos. Filter Feed pump- 15m3/hr @ 30m Head- 2 nos. Pressure Sand Filter- 1.25m X 1.8m Height (MS construction) with necessary filter media, valves, pressure gauges, backwash arrangement etc. Activated Carbon Filter- 1.25m X 1.8m Height (MS construction) with necessary filter media, valves, pressure gauges, backwash arrangement etc. (complete specifications as detailed in Part C - Sschedule Of Quantites)
VALVES
CI Butterfly valve 65mm dia (PN 10) - Providing, Fixing at site in position CI Butterfly valve (PN 10) wafer type of approved make with necessary PVC flanges, gaskets, nuts and bolts etc complete within position as per drawing - 2 ½”(65mm) dia
CI Butterfly valve 80mm dia (PN 10) - Providing, Fixing at site in position CI Butterfly valve (PN 10) wafer type of approved make with necessary PVC flanges, gaskets, nuts and bolts etc complete within position as per drawing - 3”(80mm) dia
CI Butterfly valve 100mm dia (PN 10) - Providing, Fixing at site in position CI Butterfly valve (PN 10) wafer type of approved make with necessary PVC flanges, gaskets, nuts and bolts etc complete within position as per drawing - 4”(100mm) dia
CI Butterfly valve 150mm dia (PN 10) - Providing, Fixing at site in position CI Butterfly valve (PN 10) wafer type of approved make with necessary PVC flanges, gaskets, nuts and bolts etc complete within position as per drawing - 6”(150mm) dia
CI Y Strainer 1 ½” (40mm) dia - Supply,Installation,Testing and Commisioning of CI Y-type stainer with drain plug, SS screen 304 complete in all respects -
CI Y Strainer 3” (80mm) dia - Supply,Installation,Testing and Commisioning of CI Y-type stainer with drain plug, SS screen 304 complete in all respects -
CI Y Strainer 4” (100mm) dia - Supply,Installation,Testing and Commisioning of CI Y-type stainer with drain plug, SS screen 304 complete in all respects -
CIVIL WORK FOR RCC MANHOLE
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan),including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
Carriage of materials by mechanical transport including loading, unloading and stacking beyond 50m initial lead up to 5km, including all lifts including all lifts involved as directed by Engineer in charge. Excavated Earth/Rock
1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement,including admixtures in recommended proportions as per IS: 9103 to accelerate,retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.).All works upto plinth level
Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates,anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
Steel reinforcement for R.C.C. work including straightening, cutting, bending,placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more
Centering and shuttering including strutting, propping etc. and removal of form for all heights : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
6 mm cement plaster of mix :1:3 (1 cement : 3 fine sand)
Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads,landings etc. of stair cases, including use of chequered plate wherever required, all complete
ELECTRICAL WORKS
WIRING Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. : 2 x 1.5 sq.mm + 1 x1.5 sq.mm earth wire
-do - 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earth wire
-do - 2 x 4 sq.mm +1 x 4 sq.mm earth wire
-do - 2 x 6 sq.mm +1 x 6 sq.mm earth wire
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required : 20 mm
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
Supplying and fixing suitable size modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required but excluding GI back box
Supplying and fixing suitable size modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required but excluding GI back box
Supply and fixing 3 pin, 6A ceiling rose on the existing junction box / wooden block including connection etc as required.
Installation, testing and commissioning of pre-wired, fluorescent / LED fitting / compact fluorescent / LED fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall/false ceiling, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.
Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.
MCB & DBs
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) : 8 way double door
-do- 12 way double door
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) : 4 way (4 + 12), Double door
-do- 6 way (4 + 18), Double door
-do- 8 way (4 + 24), Double door
-do- 12 way (4 + 36), Double door
Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.): 6 way (4 + 18), Double door
-do- 8 way (4 + 24), Double door
-do- 12 way (4 + 36), Double door
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C Curve" miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required : Single pole
-do- Triple pole
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “D curve" (For UPS Application) miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required : Single pole
Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.
Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.
Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.
Supplying and fixing Cable End Box (Loose wire box) suitable for double/triple pole and neutral, sheet steel, distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.
MV & HT CABLE LAYING
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required : Upto 35 sq. mm
-do- Above 35 sq. mm and upto 95 sq. mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the exisitng Trench / RCC / Hume / Metal pipe as required.: Upto 35 sq. mm
-do- Above 35 sq. mm and upto 95 sq. mm
-do- Above 95 sq. mm and upto 185 sq. mm
-do- Above 185 sq. mm and upto 400 sq. mm
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on wall surface as required.: Upto 35 sq. mm (clamped with 1mm thick saddle)
-do- Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)
-do- Above 95 sq. mm and upto 185 sq. mm (clamped with 25/ 40x3mm MS flat clamp)
-do- Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on cable tray as required : Upto 35 sq. mm (clamped with 1mm thick saddle)
-do- Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)
-do- Above 95 sq. mm and upto 185 sq. mm (clamped with 25/ 40x3mm MS flat clamp)
-do- Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)
Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.l. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.
HT CABLE LAYING Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.: Above 120 sq. mm and upto 400 sq. mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 kV grade of following size in the existing RCC/ HUME/ METAL pipe as required.: Above 120 sq. mm and upto 400 sq. mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 kV grade of following size in the existing masonry open duct/trench as required.: Above 120 sq. mm and upto 400 sq. mm
MV & HT CABLE JOINTING, END TERMINATION & CABLE TRAY
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required : 3.5cx400 sq.mm
-do- 3.5cx240 sq.mm
-do- 3.5cx185 sq.mm
-do- 3.5cx70 sq.mm
-do- 3.5cx50 sq.mm
-do- 3.5cx35 sq. mm
-do- 4cx25 sq mm
-do- 4cx16 sq mm
-do- 4cx10 sq mm
-do- 4cx6 sq mm
-do- 4cx4 sq mm
-do- 2cx16 sq mm
-do- 2cx10 sq mm
-do- 12Cx2.5 Sqmm Control cable
CABLE TRAY Supply and fixing of Perforated Cable tray with all accessories including horizontal & vertical bends, reducers, Tee's, cross over, suitable supports and brackets and other accessories as required confirming to IEC-61537. The Tray shall be galvanised for corrosion protection confirming to DIN EN 10346 / ISO 1461. The trays should be tested for a maximum safe working load of 150 Kgs with a span distance of 1.5 meters and the deflection should be within the limits as per standard. The safety factor shall be 1.7 times of the safe working load. : 100 mm width X 60mm Height
-do- 150 mm width X 60mm Height
-do- 200 mm width X 60mm Height
-do- 300 mm width X 60mm Height
-do- 400 mm width X 60mm Height
-do- 500 mm width X 60mm Height
HT PART
VCB Panel with Metering Cubicle Supply, erection, testing and commisioning of dust and vermin proof, floor mounted free standing cubicle type 11kV Outdoor VCB Panel with Metering cubicle box, fully compartmentalised complete with hinged and earthed front doors interlocked with earth switch. The unit consisting of 11kV, 630A, 20 kA, Motor operated Fixed type motor operated Vacuum Circuit Breaker (VL), Compact, Outdoor with O/C & EF self powered Relays, Extensible at both side. Metering cubicle consist of 3 phase 4 way 110V (L-L), 5A, class: 0.2S, TOD meter with RS485 port, of Electricity board approved make including all necessary accessories for fixing and connection complete as required getting tested and approved from statutory authorities, providing connection/inter-connections as required for complete installation and as instructed by engineer in charge/consultant. Also the metering cubicle unit shall comprise of 3 Nos CT's of 10VA burden, and class Cl: 0.2 S and ratio depending on contract demand including fixed type PT of ratio 11kV/110V, 25VA, Cl: 0.2s (1 No.) and seal off bushings, space heater with thermostat including 630A Copper busbars with support insulators and all other accesories as required for complete installation as required and instructed by engineer in charge/consultant.
HT PANEL Supply, installation, testing and commissioning of dust and vermin proof floor mounted free standing cubicle type, 11kV, extensible panel board made out of 14 SWG thick CRCA sheet fully compartmentalised complete with hinged and earthed front doors interlocked with the earth switch, comprising of one number of 630A VCB as incomer and two numbers of 630A VCB as outgoings as per the specification details below including providing station class polymeric type surge arrestor (10kA) for incomer with necessary switch for protection of same. Outgoings to be provided with over current + Earth fault relays with high set element, auto relays for door-interlock, provided with winding temperature alarm/trip etc. Each VCB panel also include POWER PACK/UPS of required capacity for auxilary power supply unit with all accessories required for complete installation ias required and providing all connection and interconnections as required and as instructed by engineer in charge/consultant. Incomer 1no:-11kV 630A, 3phase 50Hz, 350MVA, breaking capacity vacuum circuit breaker dust and vermin proof totally enclosed in sheet steel housing, fully inter locked, horizontal draw out and horizontal isolation, indoor truck type with trip free spring closing mechanism with mechanical ON/OFF indicators, earthing terminals automatic safety shutters, complete with auxiliary contacts, resin cast CTs of suitable ratio and accuracy class for protection & metering. Draw out type resin cast P.T with inbuilt fuses of ratio 11kV/110V, CL : 0.5, must be provided. Bus bar compartment shall have suitable capacity non-hygroscopic and high dieletric strength SMC/FRP busbar supports with electrolytic aluminium busbars covered with suitable sleeves. Metering compartment for mounting digital meter and numerical relays for feeder protection, shunt/series trip coil, under voltage release (Not required), RYB indication lamps, cable entry boxes, including all interconnections, providing fire/heat resistant coatings for busbar & CB truck enclosures and powder coating complete panel as per IS-2516 & IS 3427 with latest amendments complete as required with manually charged spring closing system. It shall also be provided with Instantenous IDMT relay 2 O/C + 1 E/F relay CDAG-51 or Equivalent with high Set, Master Trip Relay. CT Rating : 100/1/1: Core 1: CL-0.5, Core 2: 5P10. Out goings : 2 Nos:-11kV 630A, 3phase 50Hz, 350MVA, breaking capacity vacuum circuit breaker dust and vermin proof totally enclosed in sheet steel housing, fully inter locked, horizontal draw out and horizontal isolation, indoor truck type with trip free spring closing mechanism with mechanical ON/OFF indicators, earthing terminals automatic safety shutters, complete with auxiliary contacts, resin cast CTs of suitable ratio and accuracy class for protection.( complete specification as detailed in Part C - Schedule of Quantities)
HT CABLE SUPPLY Supply of following 11kV (E) grade XLPE insulated PVC sheathed compact circular armoured aluminium conductor HT power cable, insulation screened with extruded semi conducting compound in combination with copper tape suitable for 11kV earthed system confirming to relavent standard. : 3 C x 300 Sq.mm XLPE Cable
-do- 3 C x 150 Sq.mm XLPE Cable
HT CABLE END TERMINATION Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required.: 3C x 300 sq.mm.
Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required. : 3C x 300 sq.mm.
-do- 3C x 150 sq.mm.
TRANSFORMER - 630 kVA 11kV/433V Cast Resin (Dry type) Laser Scribed - Supply, installation, testing & commissioning of 630 kVA 11kV/433V indoor cast resin dry type laser scribed CRGO core transformer, (Copper Double Wound) with OLTC & RTCC having a continuous rating for 11kV / 433V 3 phase 50 Hz. Vector group Dyn 11 with tapping +5% to -15% in steps of 1.25 % by tap links, AVR & RTCC, include separate winding temperature indicator for each phase and core in the Transformer. Transformer should have cable end box on HV side suitable for 3Cx150 sq.mm XLPE cable and LV side suitable for 4RX3.5CX400 Sqmm A2XFY Cable, with all accessories, complete as required as per State electricity board, ECBC, IE rules specifications. The transformer shall confirm to IS 2067/77, 11171/1985 with latest amendment etc complete.
DIESEL GENERATORS
Supply, installation, testing and commissioning of 3phase, 415V, 0.8pf 50hz. radiator cooled DG set of the rating 500 kVA Prime Duty Diesel generating set comprising of diesel engine alternator, fuel tank, starting system, battery, battery charger, electronic governor etc with all accessories required for synchronising (Future) the DG with another DG's. The battery charger of auxillary DC power supply unit, with dry batteries with connecting leads and terminals with stationary type, high discharge perfomance, Valve Regulated Lead Acid (VRLA) sealed maintenance free, battery charger including all other accessories like interconnecting cables etc as required. The Generator set shall have a integral type acoustic enclosure as per latest CPCB II norms. Diesel engine shall be suitable for continuous operation of generator set and satisfies with EURO-II specifications. Generator set with direct injection, 6 cylinder, 4 stroke, 1500 RPM conforming to ISO 3046/1 and BS 5514 inclusive of fly wheel, flexible coupling, heavy duty air cleaner, corrosion resistor, fan with guard, fuel pump, turbocharged exhaust manifold, SS exhaust flexible connections, plate type lube oil cooler, fuel filter, lube oil filter and by-pass, electrical starting system with starter, 24 V battery with regulator, instrument panel, rpm indicator, residential silencer, heavy duty air cleaner, lube oil/coolant heater with thermostatic switch, space heater for alternator, audio/visual annunciation for faults. The DG shall have the following facility like (a) External Start/ Stop using potential free contacts (b) External Engine Speed control using potentiofree contacts including droop setting (c) External DG terminal Voltage Control using potential free contacts. Also having facility of ECU for incorporating the above features. With microprocessor based controller. Silencer shall be suitably optimized to reduce noise, with sturdy base rail and 690L free standing fuel tank. Controller shall be equiped with auto, manual, start, stop, fault reset and lamp test/panel lamp switches with alpha-numeric displays and push buttons, indications for genset running, remote start, not in auto, common shutdown, common warning, manual run mode, auto mode, stop etc with sync check. For alternator - line to neutral and line to line volts indication, current, frequency, kW, kVAr, power factor kVA and for engine following indications - DC voltage, engine speed, lube oil pressure, coolant temperature, coolant low level, comprehensive FAE data, with start/stop attempts, runnings hours, kW hours, load profile, fault history, datta logging etc and all data shall be recoreded. 500 kVA DG:- (complete specification as detailed in SOQ)
EXHAUST PIPES - Supply, erection, commissioning of additional length of exhaust pipes with long radius bend from residential silencer with necessary clamps, fixtures, civil works and painted with heat resistant, rust proof, bituminous paint of approved colors to a maximum of 10 m in stages of following sizes including suitable rain cap for top to avoid rain water entry. The distance between exhaust pipe at top and rain cap should be higher than diameter of pipe. It is also recommended that horizontal run of exhaust piping should slope downwards away from engine to the condensate trap. Silencer should be installed with drain plug at bottom. Fixing shall be done with proper clamps, expansion bolts, and all other acessories as instructed by the Engineer and the rate inclusive of all minor civil works required, bolts, clamps angle, channel, I section, necessary nut and bolt and all required accessories including cutting, hoisting, fixing in position and applying 2 coats of primer and 2 coats of enamel paint of approved quality etc as required in the steel works etc as required for istallation. Support to exhaust piping should be done in such a manner that load of exhaust piping is not exerted to turbocharger. Exhaust pipe height shall be 3m more than the top of any adjacent building withing 10m radius of the exhaust. : 200mm dia
AUTO POWER FACTOR CORRECTION
LT PANELS
MAIN PANEL Fabrication, supply, erection, testing and commissioning of Type Tested Assembly (TTA) cubicle type (panel and all switch gears should be type tested and certification should be submitted) as per IEC 61439 and internal arc test as per IEC 61641, dust and vermin proof, floor mounted, front operated MV Main panel board made out of 14 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. This panel should include Pluggable type surge arrester Class B & Class C / Class 1 & Class 2 as per IEC 61643 (IP 20) with potential free contact, completely assembled enclosure & provision for inbuilt common remote indication for defective arresters 3 nos of encapsulated spark gap & 3 nos of single large block of MOV with series thermal fuse and cooling gel to connect between Line and Neutral and one number arrester encapsulated spark gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage - 230V 50Hz, Impulse current-150 KA (10/350µ sec) & 60KA (8/20µ sec) for Line to Neutral & 125 KA(10/350µ sec) for Neutral to Protective Earth, voltage protection level <1.3 KV ( L to N) & <1.3 KV (N to E). Operating temp -40º to +85ºC. Response time <100 nano secincluding necessary MCCB for protection of same. Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. Incomers EB Incomer 1 & 2 - 1000A, 50kA, FP, EDO Microprocessor based ACB with 3 O/C and 1 E/F releases. Standby low set E/F relay with CT at neutral earthing conductor, O/V relay with primary trip - 2 Set. DG Feeder 1 & 2 - 1000A, 50kA, FP, EDO Microprocessor based ACB with overload and E/F release Standby low set E/F relay with CT at neutral earthing conductor - 2 Sets. 2000A 415V, 50kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Necessary interlocking arrangement. ( complete specification as detailed in Part C - Schedule of Quantities)
MEDICAL GAS PLANT LOAD BANK / SM DB Supply, erection, testing and commissioning of wall mounting type, double door 3 phase 8 way Load Bank of approved make IP43 and quality with cable end box, meter module including busbar, neutral link and DIN bar with all accessories etc complete with all connections and inter-connections as shown in the schematic drawing, Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant. This panel should include pluggable type surge arrester in suitable enclosure Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with potential free contact, thermal dis connector & provision for inbuilt common remote indication for defective arresters to connect between Line and Neutral and one number arrester Spark Gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, type single MOV with built in thermal fuse and cooling gel(L to N) & spark gap encapsulated / non exhausting (N to E) . Lightning Impulse Current - 21 kA (10/350µ sec) for Line to Neutral & 25 kA(10/350µ sec) for Neutral to Earth,Nominal discharge current-30 kA (8/20µ sec) for Line to Neutral & 40 kA(8/20µ sec) for Neutral to Earth, max discharge current 150 kA (8/20µ sec) for Line to Neutral & 50 kA(8/20µ sec) for Neutral to Earth. Voltage protection level 1300V (L to N) & 1200V (N to E). Operating temp -40º to +80ºC. Response time <25 nano sec (L to N), < 100 nano sec (N to E) DIN rail mounting type etc complete with back up fuse as required and as directed. Incomer - 125A FP 25kA thermal magnetic release MCCB - 1No. 125A 415V 25kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Prewired digital meter module including all meters and indicating lamps - 1 No; Cable alley - 2 Nos; Class B+C / Class 1+2 Surge arrestor device with enclosure & necessary MCCB for protection of same - 1 No. Outgoings 63A 16kA TP MCCB, with thermal magnetic releas - 4 Nos.; 50A 16kA TP MCCB, with thermal magnetic releas - 2 Nos.; 40A 16kA TP MCCB, with thermal magnetic releas - 1 No.; Supply, Installation, testing and commisioning
CSSD LOAD BANK / SM DB Supply, erection, testing and commissioning of wall mounting type, double door 3 phase 6 way Load Bank of approved make IP43 and quality with cable end box, meter module including busbar, neutral link and DIN bar with all accessories etc complete with all connections and inter-connections as shown in the schematic drawing, Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant. This panel should include pluggable type surge arrester in suitable enclosure Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with potential free contact, thermal dis connector & provision for inbuilt common remote indication for defective arresters to connect between Line and Neutral and one number arrester Spark Gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, type single MOV with built in thermal fuse and cooling gel(L to N) & spark gap encapsulated / non exhausting (N to E) . Lightning Impulse Current - 21 kA (10/350µ sec) for Line to Neutral & 25 kA(10/350µ sec) for Neutral to Earth,Nominal discharge current-30 kA (8/20µ sec) for Line to Neutral & 40 kA(8/20µ sec) for Neutral to Earth, max discharge current 150 kA (8/20µ sec) for Line to Neutral & 50 kA(8/20µ sec) for Neutral to Earth. Voltage protection level 1300V (L to N) & 1200V (N to E). Operating temp -40º to +80ºC. Response time <25 nano sec (L to N), < 100 nano sec (N to E) DIN rail mounting type etc complete with back up fuse as required and as directed. Incomer - 250 A FP 25kA Thermal Magnetic Release MCCB - 1No. 250A 415V 25kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Prewired meter module including all meters and indicating lamps - 1 Set; Cable alley - 2 Set; Class B+C / Class 1+2 Surge arrestor device with enclosure & necessary MCCB for protection of same - 1 No. Outgoings 80A 16kA TP MCCB, with thermal magnetic releas - 2 Nos.; 63A 16kA TP MCCB, with thermal magnetic releas - 2 Nos.;50A 16kA TP MCCB, with thermal magnetic releas - 1 No.; 40A 16kA TP MCCB, with thermal magnetic releas - 1 No.; Supply, Installation, testing and commisioning
GF LOAD BANK / SM DB Supply, erection, testing and commissioning of wall mounting type, double door 3 phase 12 way Load Bank of approved make IP43 and quality with cable end box, meter module including busbar, neutral link and DIN bar with all accessories etc complete with all connections and inter-connections as shown in the schematic drawing, Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant. This panel should include pluggable type surge arrester in suitable enclosure Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with potential free contact, thermal dis connector & provision for inbuilt common remote indication for defective arresters to connect between Line and Neutral and one number arrester Spark Gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, type single MOV with built in thermal fuse and cooling gel(L to N) & spark gap encapsulated / non exhausting (N to E) . Lightning Impulse Current - 21 kA (10/350µ sec) for Line to Neutral & 25 kA(10/350µ sec) for Neutral to Earth,Nominal discharge current-30 kA (8/20µ sec) for Line to Neutral & 40 kA(8/20µ sec) for Neutral to Earth, max discharge current 150 kA (8/20µ sec) for Line to Neutral & 50 kA(8/20µ sec) for Neutral to Earth. Voltage protection level 1300V (L to N) & 1200V (N to E). Operating temp -40º to +80ºC. Response time <25 nano sec (L to N), < 100 nano sec (N to E) DIN rail mounting type etc complete with back up fuse as required and as directed. Incomer - 160 A FP 25kA Thermal Magnetic Release MCCB - 1No. 160A 415V 25kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Prewired meter module including all meters and indicating lamps - 1 Set. Cable alley - 2 Set. Class B+C / Class 1+2 Surge arrestor device with enclosure & necessary MCCB for protection of same - 1 No. Outgoings 80A 16kA TP MCCB, with thermal magnetic releas - 1 No.; 40A 16kA TP MCCB, with thermal magnetic releas - 6 Nos.; 25A 16kA TP MCCB, with thermal magnetic releas - 5 Nos.; Supply, Installation, testing and commisioning
2F & 3F LOAD BANK / SM DB TYPICAL Supply, erection, testing and commissioning of wall mounting type, double door 3 phase 12 way Load Bank of approved make IP43 and quality with cable end box, meter module including busbar, neutral link and DIN bar with all accessories etc complete with all connections and inter-connections as shown in the schematic drawing, Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant. This panel should include pluggable type surge arrester in suitable enclosure Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with potential free contact, thermal dis connector & provision for inbuilt common remote indication for defective arresters to connect between Line and Neutral and one number arrester Spark Gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, type single MOV with built in thermal fuse and cooling gel(L to N) & spark gap encapsulated / non exhausting (N to E) . Lightning Impulse Current - 21 kA (10/350µ sec) for Line to Neutral & 25 kA(10/350µ sec) for Neutral to Earth,Nominal discharge current-30 kA (8/20µ sec) for Line to Neutral & 40 kA(8/20µ sec) for Neutral to Earth, max discharge current 150 kA (8/20µ sec) for Line to Neutral & 50 kA(8/20µ sec) for Neutral to Earth. Voltage protection level 1300V (L to N) & 1200V (N to E). Operating temp -40º to +80ºC. Response time <25 nano sec (L to N), < 100 nano sec (N to E) DIN rail mounting type etc complete with back up fuse as required and as directed. Incomer - 200 A FP 25kA Thermal Magnetic Release MCCB - 1No. 200A 415V 25kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Prewired meter module including all meters and indicating lamps - 1 Set. Cable alley - 2 Set. Class B+C / Class 1+2 Surge arrestor device with enclosure & necessary MCCB for protection of same - 1 No. Outgoings 63A 16kA TP MCCB, with thermal magnetic releas - 3 Nos. 40A 16kA TP MCCB, with thermal magnetic releas - 4 Nos. 25A 16kA TP MCCB, with thermal magnetic releas - 5 Nos. Supply, Installation, testing and commisioning
4F LOAD BANK / SM DB Supply, erection, testing and commissioning of wall mounting type, double door 3 phase 12 way Load Bank of approved make IP43 and quality with cable end box, meter module including busbar, neutral link and DIN bar with all accessories etc complete with all connections and inter-connections as shown in the schematic drawing, Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant. This panel should include pluggable type surge arrester in suitable enclosure Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with potential free contact, thermal dis connector & provision for inbuilt common remote indication for defective arresters to connect between Line and Neutral and one number arrester Spark Gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, type single MOV with built in thermal fuse and cooling gel(L to N) & spark gap encapsulated / non exhausting (N to E) . Lightning Impulse Current - 21 kA (10/350µ sec) for Line to Neutral & 25 kA(10/350µ sec) for Neutral to Earth,Nominal discharge current-30 kA (8/20µ sec) for Line to Neutral & 40 kA(8/20µ sec) for Neutral to Earth, max discharge current 150 kA (8/20µ sec) for Line to Neutral & 50 kA(8/20µ sec) for Neutral to Earth. Voltage protection level 1300V (L to N) & 1200V (N to E). Operating temp -40º to +80ºC. Response time <25 nano sec (L to N), < 100 nano sec (N to E) DIN rail mounting type etc complete with back up fuse as required and as directed. Incomer - 250 A FP 25kA Thermal Magnetic Release MCCB - 1No. 250A 415V 25kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Prewired meter module including all meters and indicating lamps - 1 Set. Cable alley - 2 Set, Class B+C / Class 1+2 Surge arrestor device with enclosure & necessary MCCB for protection of same - 1 No. , Outgoings 125A 16kA TP MCCB, with thermal magnetic releas - 1 No. 63A 16kA TP MCCB, with thermal magnetic releas - 3 Nos. 40A 16kA TP MCCB, with thermal magnetic releas - 3 No. , 25A 16kA TP MCCB, with thermal magnetic releas - 5 Nos., Supply, Installation, testing and commisioning
5F LOAD BANK / SM DB Supply, erection, testing and commissioning of wall mounting type, double door 3 phase 8 way Load Bank of approved make IP43 and quality with cable end box, meter module including busbar, neutral link and DIN bar with all accessories etc complete with all connections and inter-connections as shown in the schematic drawing, Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant. This panel should include pluggable type surge arrester in suitable enclosure Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with potential free contact, thermal dis connector & provision for inbuilt common remote indication for defective arresters to connect between Line and Neutral and one number arrester Spark Gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, type single MOV with built in thermal fuse and cooling gel(L to N) & spark gap encapsulated / non exhausting (N to E) . Lightning Impulse Current - 21 kA (10/350µ sec) for Line to Neutral & 25 kA(10/350µ sec) for Neutral to Earth,Nominal discharge current-30 kA (8/20µ sec) for Line to Neutral & 40 kA(8/20µ sec) for Neutral to Earth, max discharge current 150 kA (8/20µ sec) for Line to Neutral & 50 kA(8/20µ sec) for Neutral to Earth. Voltage protection level 1300V (L to N) & 1200V (N to E). Operating temp -40º to +80ºC. Response time <25 nano sec (L to N), < 100 nano sec (N to E) DIN rail mounting type etc complete with back up fuse as required and as directed. Incomer - 200 A FP 25kA thermal magnetic release MCCB - 1No. 200A 415V 25kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Prewired meter module including all meters and indicating lamps - 1 Set; Cable alley - 2 Set; Class B+C / Class 1+2 Surge arrestor device with enclosure & necessary MCCB for protection of same - 1 No. Outgoings 63A 16kA TP MCCB, with thermal magnetic releas - 3 Nos. 40A 16kA TP MCCB, with thermal magnetic releas - 2 Nos. 25A 16kA TP MCCB, with thermal magnetic releas - 3 Nos. Supply, Installation, testing and commisioning
6F LOAD BANK / SM DB 1 Supply, erection, testing and commissioning of wall mounting type, double door 3 phase 6 way Load Bank of approved make IP43 and quality with cable end box, meter module including busbar, neutral link and DIN bar with all accessories etc complete with all connections and inter-connections as shown in the schematic drawing, Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant. This panel should include pluggable type surge arrester in suitable enclosure Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with potential free contact, thermal dis connector & provision for inbuilt common remote indication for defective arresters to connect between Line and Neutral and one number arrester Spark Gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, type single MOV with built in thermal fuse and cooling gel(L to N) & spark gap encapsulated / non exhausting (N to E) . Lightning Impulse Current - 21 kA (10/350µ sec) for Line to Neutral & 25 kA(10/350µ sec) for Neutral to Earth,Nominal discharge current-30 kA (8/20µ sec) for Line to Neutral & 40 kA(8/20µ sec) for Neutral to Earth, max discharge current 150 kA (8/20µ sec) for Line to Neutral & 50 kA(8/20µ sec) for Neutral to Earth. Voltage protection level 1300V (L to N) & 1200V (N to E). Operating temp -40º to +80ºC. Response time <25 nano sec (L to N), < 100 nano sec (N to E) DIN rail mounting type etc complete with back up fuse as required and as directed. Incomer - 250 A FP 25kA thermal magnetic release MCCB - 1No. 250A 415V 25kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Prewired meter module including all meters and indicating lamps - 1 Set. Cable alley - 2 Set. Class B+C / Class 1+2 Surge arrestor device with enclosure & necessary MCCB for protection of same - 1 No.; Outgoings 125A 16kA TP MCCB, with thermal magnetic releas - 3 Nos.; 40A 16kA TP MCCB, with thermal magnetic releas - 2 Nos.; 25A 16kA TP MCCB, with thermal magnetic releas - 3 Nos., Supply, Installation, testing and commisioning
6F LOAD BANK / SM DB 2 Supply, erection, testing and commissioning of wall mounting type, double door 3 phase 8 way Load Bank of approved make IP43 and quality with cable end box, meter module including busbar, neutral link and DIN bar with all accessories etc complete with all connections and inter-connections as shown in the schematic drawing, Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant. This panel should include pluggable type surge arrester in suitable enclosure Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with potential free contact, thermal dis connector & provision for inbuilt common remote indication for defective arresters to connect between Line and Neutral and one number arrester Spark Gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, type single MOV with built in thermal fuse and cooling gel(L to N) & spark gap encapsulated / non exhausting (N to E) . Lightning Impulse Current - 21 kA (10/350µ sec) for Line to Neutral & 25 kA(10/350µ sec) for Neutral to Earth,Nominal discharge current-30 kA (8/20µ sec) for Line to Neutral & 40 kA(8/20µ sec) for Neutral to Earth, max discharge current 150 kA (8/20µ sec) for Line to Neutral & 50 kA(8/20µ sec) for Neutral to Earth. Voltage protection level 1300V (L to N) & 1200V (N to E). Operating temp -40º to +80ºC. Response time <25 nano sec (L to N), < 100 nano sec (N to E) DIN rail mounting type etc complete with back up fuse as required and as directed. Incomer - 320 A FP 25kA thermal magnetic release MCCB - 1No. 320A 415V 25/36kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Prewired meter module including all meters and indicating lamps - 1 Set; Cable alley - 2 Set; Class B+C / Class 1+2 Surge arrestor device with enclosure & necessary MCCB for protection of same - 1 No. Outgoings 160A 16kA TP MCCB, with thermal magnetic releas - 2 Nos. 125A 16kA TP MCCB, with thermal magnetic releas - 1 No. 100A 16kA TP MCCB, with thermal magnetic releas - 3 Nos. 80A 16kA TP MCCB, with thermal magnetic releas - 1 No. 50A 16kA TP MCCB, with thermal magnetic releas - 1 No. Supply, Installation, testing and commisioning
5F UPS LOAD BANK / SM DB Supply, erection, testing and commissioning of wall mounting type, double door 3 phase 16 way Load Bank of approved make IP43 and quality with cable end box, meter module including busbar, neutral link and DIN bar with all accessories etc complete with all connections and inter-connections as shown in the schematic drawing, Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant. This panel should include pluggable type surge arrester in suitable enclosure Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with potential free contact, thermal dis connector & provision for inbuilt common remote indication for defective arresters to connect between Line and Neutral and one number arrester Spark Gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, type single MOV with built in thermal fuse and cooling gel(L to N) & spark gap encapsulated / non exhausting (N to E) . Lightning Impulse Current - 21 kA (10/350µ sec) for Line to Neutral & 25 kA(10/350µ sec) for Neutral to Earth,Nominal discharge current-30 kA (8/20µ sec) for Line to Neutral & 40 kA(8/20µ sec) for Neutral to Earth, max discharge current 150 kA (8/20µ sec) for Line to Neutral & 50 kA(8/20µ sec) for Neutral to Earth. Voltage protection level 1300V (L to N) & 1200V (N to E). Operating temp -40º to +80ºC. Response time <25 nano sec (L to N), < 100 nano sec (N to E) DIN rail mounting type etc complete with back up fuse as required and as directed. Incomer - 200 A FP 25kA thermal magnetic release MCCB - 1No. 200A 415V 25kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Prewired meter module including all meters and indicating lamps - 1 Set. Cable alley - 2 Set. Class B+C / Class 1+2 Surge arrestor device with enclosure & necessary MCCB for protection of same - 1 No. Outgoings 40A 16kA TP MCCB, with thermal magnetic releas - 12 Nos. 25A 16kA TP MCCB, with thermal magnetic releas - 4 Nos. Supply, Installation, testing and commisioning
UPS INPUT PANEL Fabrication, supply, erection, testing and commissioning of Type Tested Assembly (TTA) cubicle type (panel and all switch gears should be type tested and certification should be submitted) as per IEC 61439 and internal arc test as per IEC 61641, dust and vermin proof, floor mounted, front operated MV panel board made out of 16 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as required. All opening parts of the panel shall be sealable.This panel should include pluggable type surge arrester in suitable enclosure Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with potential free contact, thermal dis connector & provision for inbuilt common remote indication for defective arresters to connect between Line and Neutral and one number arrester Spark Gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, type single MOV with built in thermal fuse and cooling gel(L to N) & spark gap encapsulated / non exhausting (N to E) . Lightning Impulse Current - 21 kA (10/350µ sec) for Line to Neutral & 25 kA(10/350µ sec) for Neutral to Earth,Nominal discharge current-30 kA (8/20µ sec) for Line to Neutral & 40 kA(8/20µ sec) for Neutral to Earth, max discharge current 150 kA (8/20µ sec) for Line to Neutral & 50 kA(8/20µ sec) for Neutral to Earth. Voltage protection level 1300V (L to N) & 1200V (N to E). Operating temp -40º to +80ºC. Response time <25 nano sec (L to N), < 100 nano sec (N to E) DIN rail mounting type etc complete with back up fuse as required and as directed. Incomer - 400A, 36kA, FP TM Based MCCB - 1No. 400A 433V, 36kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. RYB phase indicating LED lamps with control fuses and switches - 1 set. Outgoing 250A, 36kA, TP, MCCB - 3 Nos. Supply, Installation, testing and commisioning
UPS OUTPUT PANEL Fabrication, supply, erection, testing and commissioning of Type Tested Assembly (TTA) cubicle type (panel and all switch gears should be type tested and certification should be submitted) as per IEC 61439 and internal arc test as per IEC 61641, dust and vermin proof, floor mounted, front operated MV panel board made out of 16 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as required. All opening parts of the panel shall be sealable. Incomer - 400A, 36kA, FP TM Based MCCB - 2No. 400A 433V, 36kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. RYB phase indicating LED lamps with control fuses and switches - 1 set. Outgoing 200A FP 36kA TM Based MCCB - 3 Nos. Supply, Installation, testing and commisioning
AUTO TRANSFER SWITCH WITH ENCLOSURE Supply, erection, testing and commissioning of following capacity auto transfer switch ATys M 3s C30 with elclosure, bus bars and all accessories required for complate operation as per the drawing. The ATS should be double break contact system for high short time withstand. ATS shall be with UV/OV, Phase sequence, Single phasing and freequency protections. : 200A 4P ATS
-do- 100A 4P ATS
-do- 80A 4P ATS
-do- 63A 4P ATS
CABLES & END TERMINATION
LT CABLE SUPPLY Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. 3.5cx400sq.mm Al Cable
-do- 3.5cx240sq.mm Al Cable
-do- 3.5cx185sq.mm Al Cable
-do- 3.5cx70sq.mm Al Cable
-do- 3.5cx50sq.mm Al Cable
-do- 3.5cx35sq.mm Al Cable
-do- 4cx25sq.mm Al Cable
-do- 4x16sq.mm Al Cable
-do- 4x10sq.mm Al Cable
-do- 4x6sq.mm Al Cable
-do- 4x4sq.mm Al Cable
-do- 2x16sq.mm Al Cable
-do- 2x10sq.mm Al Cable
-do- 12x2.5sq.mm Cu Control Cable
Supply and laying and clamping of the following PVC sheathed unarmoured power cable conductor of best conductivity copper solid/stranded conductor, XLPE insulated, PVC inner sheathed 1.1kV grade strictly conforming to IS:1554 (Part-I) 1964 of the following sizes in meduin duty conduit / cable tray /wall using factory made heavy gauge GI/painted MS clamps. Space between clamps not exceeding 60cms amd making good the damages colour washing etc as required. and instructed by engineer at site/consultant. : 1Cx150 Sq.mm Copper Flexible Cable
END TERMINATION Supply of superior quality copper tubular cable socket and making core termination of cables of the following sizes including crimping etc. as required. : 1CX150 sq.mm Cu Cable
LIGHT & FAN FIXTURES
INTERIOR LIGHT FIXTURES Supply of Linear Surface Mounted LED Batten with a nominal system lumen output of 2000 lumens. System wattage should not exceed 20W. The luminaire shall have a rated system lifetime of 50,000 burning hours at 70. The luminaire should have a color temperature of 6500K and CRI>80. Driver of the luminaire shall have THD < 20% and PF > 0.95. The heat sink should be made of Extruded therma polycarbonate and the luminaire optics shall have a high efficiency PC diffuser. The light fixture including driver shall comply to IEC and IS. Similar to Wipro Make Model No: LL20-221-XXX-65-NE GR or equivalent.
Supply of Recessed round LED Downlighter with a nominal system lumen output of 1125 lumens. System wattage should not exceed 15W. The luminaire shall have a rated system lifetime of 50,000 burning hours. The luminaire should have a color temperature of 5700K and CRI>80. Driver of the luminaire shall have THD < 10% and PF > 0.95. The heat sink should be made of die cast aluminium and the luminaire optics shall have a high efficiency diffuser. The light fixture including driver shall comply to IEC and IS. Similar to Wipro Make LD71-161-SML-57-XX or equivalent.
Supply of Recessed mounted Square LED Downlighter, high efficiency with a nominal system lumen output of 1527 lumens. Luminaire wattage should not exceed 18W. The luminaire should have a CRI>80. Driver of the luminaire shall have THD<20% and PF > 0.9. The heat sink should be made of die cast aluminium and the luminaire optics shall have a high efficiency PC diffuser. Aesthetically designed 1X1 LED flat panel of surface mounting which provides soft-light and glare free symmetrical illumination. Similar to wipro make Model No: LD81-171-XXX-60-XX or equivalent.
Supply of Surface mounted Square LED Downlighter, high efficiency with a nominal system lumen output of 1527 lumens. Luminaire wattage should not exceed 18W. The luminaire should have a CRI>80. Driver of the luminaire shall have THD<20% and PF > 0.9. The heat sink should be made of die cast aluminium and the luminaire optics shall have a high efficiency PC diffuser. Aesthetically designed 1X1 LED flat panel of surface mounting which provides soft-light and glare free symmetrical illumination. Similar to wipro make model No: LD81-171-XXX-60-SM or equivalent.
Supply of Recessed LED Clean Room Luminaire (CRL) with a nominal system lumen output of 4100 lumens and a minimum system efficacy of 95 lm/W. The luminaire shall have a rated system lifetime of 50,000 burning hours at L70. The luminaire should have a CRI > 80. The luminaire shall meet IP54 rating with THD<10% and PF>0.9. The luminaire housing should made of powder coated CRCA sheet steel with HET Diffuser. The total power consumption should not exceed42W (including driver). LED Shall be with ANSI Bin C78.377A & IEC62471 Similar to Wipro Make LC20-551-XXX-57-XX or equivalent.
Supply of Recessed 2X2 LED fixture (For ICU, Wards, CCU etc) with a nominal system lumen output of minimu 3000 lumens. System wattage should not exceed 31W. The luminaire shall have a rated system lifetime of 50,000 burning hours. The luminaire should have a color temperature of 5700K and CRI>80. Driver of the luminaire shall have THD < 10% and PF > 0.95. Housing shall be CRCA powder coated with PMMA diffuser.Driver shall have 85% efficiency. LED shall comply to ANSI Bin C78.377A & IEC62471. Similar to Wipro Make CRCO10R038HP57G1 or Eqivalent
Supply of Recessed 2X2 LED fixture (For Common area, lobby etc) with a nominal system lumen output of minimu 3300 lumens. System wattage should not exceed 36W. The luminaire shall have a rated system lifetime of 50,000 burning hours. The luminaire should have a color temperature of 5700K and CRI>80. Driver of the luminaire shall have THD < 10% and PF > 0.95. Housing shall be CRCA powder coated with PMMA diffuser.Driver shall have 85% efficiency. LED shall comply to ANSI Bin C78.377A & IEC62471. Similar to Wipro Make CRCO10R036HP57G1 or Eqivalent
Supply of Recessed 2X2 LED fixture (For Corridor, general area etc) with a nominal system lumen output of minimu 3100 lumens. System wattage should not exceed 36W. The luminaire shall have a rated system lifetime of 50,000 burning hours. The luminaire should have a color temperature of 5700K and CRI>80. Driver of the luminaire shall have THD < 10% and PF > 0.95. Housing shall be CRCA powder coated with PMMA diffuser.Driver shall have 85% efficiency. LED shall comply to ANSI Bin C78.377A & IEC62471. Similar to Wipro Make CRCO10R038HP57GL or Eqivalent
Supply of Surface Mounted 2X2 LED fixture (For external corridor, porch area etc) with a nominal system lumen output of minimum 3000 lumens. System wattage should not exceed 36W. The luminaire shall have a rated system lifetime of 50,000 burning hours. The luminaire should have a color temperature of 5700K and CRI>80. Driver of the luminaire shall have THD < 10% and PF > 0.95. Housing shall be CRCA powder coated with PMMA diffuser.Driver shall have 85% efficiency. LED shall comply to ANSI Bin C78.377A & IEC62471. Similar to Wipro Make CRCO10S038HP57GL or Eqivalent
Supply of Surface mounted LED 4X1 LED luminaire with luminaire wattage should not exceed 31W and nominal system lunens not less than 3000 Lumens.The luminaire should have a color temperature of 5700K and CRI>80. Diffuser material should be of PolyCarbonate PMMA and housing shall be powder coated CRCA.. Driver of the luminaire shall have THD<10% and PF > 0.9. The driver shall comply to IEC standards. Similar to Wipro Make CRCO13S038HP57G1 - Environmental friendly, new generation, aesthetically designed, ultra modern Surface mounting luminare with high brightness SMD LED as light source. Similar to Wipro Make Model No: CRCO13S038HP57G1 or equivalent.
Supply of LED Bulk Head Luminaire with max wattage of 10W with system lumens not less than 720 Lumes. The luminaire shall have a rated system lifetime of 50,000 burning hours at L70. Housing shall be pressure die cast aluminum with IP 65 rating. luminaire should have a color temperature of 5700K and CRI>80. Driver of the luminaire shall have THD<10% and PF >0.9. There should be in-built surge protection upto 2 KV. The LED Shall be ANSI Bin C78.377A and IEC62471 with class1 electrical insulation. Similar to Wipro Make LW07-141-XXX-57-XX or Equivalent.
EXTERIOR LIGHT FIXTURES Supply, fixing, testing and commissioning of 7 M octagonal poles of approved Make having top dia 70 mm, bottom dia 130 mm, Sheet thickness 3 mm, pitch circle dia (PCD) of 200 mm, Base plate diamentions 200mm length x 200mm bredth x 12mm thickness, EN8 grade Foundation bolts of size 4 x 20 mm dia, having bolt length of 600 mm. The Octagonal Poles shall be designed to withstand the maximum wind speed as per IS 875. The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding. The octagonal Poles shall have door of approximate 500 mm length at the elevation of 500 mm from the Base plate. The door shall be vandal resistance and shall be weather proof to ensure safety of inside connections. The door shall be flush with the exterior surface and shall have suitable locking arrangement. There shall also be suitable arrangement for the purpose of earthing. Material Octagonal Poles HT Steel Conforming to grade S355JO. Base Plate Fe 410 conforming to IS 226 / IS 2062 Foundation Bolts EN.8 grade (Similar to Make - Bajaj or Equivalent). The poles shall be hot dip galvanised as per IS 2629 / IS 2633 / IS 4759 standards with average coating thickness of 85 micron. The galvanizing shall be done in single dipping. The pole shall be with one arm of minimum 1 meter long with 70 W LED fixture (Similar to Wipro Make LR02-781-XXX-57-XX or equivalent). The cost inclusive of all material required for complete installation including light fixture, pole, foundation etc. required as per the specification.
Supply, fixing, testing and commissioning of 5 M octagonal poles of approved Make having top dia 70 mm, bottom dia 130 mm, Sheet thickness 3 mm, pitch circle dia (PCD) of 200 mm, Base plate diamentions 200mm length x 200mm bredth x 12mm thickness, EN8 grade Foundation bolts of size 4 x 16 mm dia, having bolt length of 450 mm. The Octagonal Poles shall be designed to withstand the maximum wind speed as per IS 875. The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding. The octagonal Poles shall have door of approximate 500 mm length at the elevation of 500 mm from the Base plate. The door shall be vandal resistance and shall be weather proof to ensure safety of inside connections. The door shall be flush with the exterior surface and shall have suitable locking arrangement. There shall also be suitable arrangement for the purpose of earthing. Material Octagonal Poles HT Steel Conforming to grade S355JO. Base Plate Fe 410 conforming to IS 226 / IS 2062Foundation Bolts EN.8 grade The poles shall be hot dip galvanised as per IS 2629 / IS 2633 / IS 4759 standards with average coating thickness of 85 micron. The galvanizing shall be done in single dipping. The pole shall be with one arm of minimum 0.5 meter long for fixing 45 W LED fixture (Similar to Wipro make : LR02-501-XXX-57-XX LED Street Light). The cost inclusive of all material required for complete installation including light fixture, pole, foundation etc. required as per the specification.
Supply and instalation, testing and commisioning of Aviation obstuction light with built-in 75VA step up transformer with yellow coloured die cast aluminium alloy housing, Neon spiral lamp plugged into spring loaded high tension nylon socket and wired upto the terminal block., heat resistant, clear, toughened, thick glass dome mounted on hinge die cast aluminium ring secured to the body by two studs and wing nuts, 38mm dia threaded stem with lock nuts for mounting on pipe above structure, heavy duty and wheather proof, indicating aviation obstructions in flying paths and provide light with 360 Deg visibility. The enclosure shall be IP 54. It shall be designed to meet International Civil Aviation Organistion Standards. Operating Voltage 230 V AC. Power Consumption > 5W. Light Intensity > 15 cd. Average life time 50,000 hrs at 70 % lumen maintenance. (Bajaj make BJOL 1 or equivalent)
FAN FIXTURES Supplying of ceiling fan of 1200mm sweep, energy efficient 5 Star rated, BLDC motor, High Speed, high power factor above 0.95 including the down rod of standard length (upto 30 cm). Similar to CG make Energion HS or equivalent.
Supply, installation, testing and commissioning of wall fan of 450mm sweep, 1200 RPM, 70 Cu.Mtr/Min Air delivery. Plastic body & blades with pull cords for speed regulation & wide oscillation control. Aerodynamically designed blades for high air efficiency. Similar to Crompron Greeves Make, Model No: High Flo LG 18 or equivalent.
PVC FLEXIBLE CONDUIT
Supply and clamping the following size of corrugated pvc fiexible conduit with necessary locking ring and check nut at termination pointed using suitable size GI/painted MS saddles spacing not exceeding 60 cms on surface including making good the damages, colour washing etc.as required : 20mm dia
-do - 25mm dia
RCBO Supplying, fixing, testing and commissioning following four pole / double pole, 415 volts and 240 volts, residual current circuit breaker with overload protection (RCBO) of the following rating and sensitivity current in the existing MCB SPN and TPN horizontal/vertical DB's complete with connections, etc. as required and instructed by engineer in charge/consultant. : 25A, 100mA, 30 MS, DP RCBO
-do - 40A, 100mA, 30 MS, DP RCBO
-do - 25A, 30mA, 30 MS, FP, RCBO
-do - 32A, 100mA, 30 MS, FP, RCBO
-do - 40A, 100mA, 30 MS, FP, RCBO
-do - 63A, 100mA, 30 MS, FP, RCBO
MCCB: Supply, fixing, testing and commisioning of following rating, breaking capacity and pole, type MCCB in existing Vertical Distribution Board with spredear links, terminal connections and all accesories as required making all necessary connections etc as required and instructed by engineer in charge/consultant. - 63 Amp 25kA FP MCCB with Thermal - Magnetic Release
-do- 80 Amp 25kA FP MCCB with Thermal - Magnetic Release
-do- 100 Amp 25kA FP MCCB with Thermal - Magnetic Release
Wiring for Staircase Light Point Wiring for stair case light points with 2.5 sq.mm FRLS PVC insulated copper conductor single core cable in and including surface / recessed medium class PVC conduit and all acessories required for complete installation etc , with 1 way modular switch, modular plate, suitable GI box medium class PVC conduit and all acessories required etc and earthing the point with 2.5 sq.mm FRLS PVC insulated copper conductor single core cable etc as required and instructed by engineer in charge/consultant. (Note - Staircase light point shall be controlled by a single switch located inside fire control room in ground floor as per latest fire norms) : One light point controlled by one way switch (at ground floor)
-do- Loop wiring for Light point
Computer Point Wiring for computer point using 2 Nos 6A plug points controlled by 2 Nos independent 6A switches using 1.5 sq.mm FRLS PVC insulated copper single core stranded wire and earthing using using 1.5 Sqmm FRLS PVC insulated copper single core stranded wire, green colour continuous run thorough conduit as per IS, earthing etc in surface/ recessed medium class PVC conduit including all acessories as required for complete installation and as directed by engineer in charge and making good all damages made for installation. Cost inclusive of sockets, switchs, suitable cover plate and base plate and suitable size GI box with all accesoires required for complete installation etc. Circuit main shall be measured seperatly (Separate colour shall be provided for switches, faceplate and cover plate and same shall be finalized with site in charge / client).
Supply and fixing of following FP 415V, isolators in sheet steel powder coated enclosure with door interlock and padlock facility on surface confirming to IEC 60947-3 complete with all accesories, connections, testing and commissioning etc as required and as instructed by engineer in charge also making good any damages made during installation. : 50A FP Isolator with enclosure
-do- 63A FP Isolator with enclosure
-do- 80A FP Isolator with enclosure
-do- 100A FP Isolator with enclosure
-do- 250A FP Isolator with enclosure
MCB Supply, installation, testing and commisioning of following rating SP/TP C curve MCB, 16kA as per IS/IEC 60898-12002 in the existing MCB VDB including all connections and iterconnections as required and as instructed by engineer in charge/consultant. - 40A SP MCB
-do- 6-32 TP MCB
-do- 40A TP MCB
-do- 63A TP MCB
3 X 100 kVA UPS in PRS Mode Supply, installation, and commissioning of 3 x 100 kW UPS three phase in and out with built in PRS configuration. with indoor (IP20) with surge protection system with 15 min backup battery @ 100 kW load (SMF battery of reputed approved make), having individual battery bank with Min VAH 86400 per ups, Input pf >0.99, Input THDi <3%, External / internal isolation transformers at output side to have transformer output even in the bypass mode, with necessary battery circuit breaker, double conversion technology with input 400V, 50Hz three phase, output 400V, 50Hz three phase, SNMP card for network monitoring, BMS compatibility etc. It shall be 100% generator compatible, with Efficiency > 96 % and output power factor Unity ( 100 kVA = 100 kW), Eco mode Efficiency 99% and including all accessories etc as required.The system shall comply to IEC /EN 62040-1 and relevant IS standard. The acoustic noise at 1m of the system should be <60dB.The system shall comply to IEC /EN 62040-1, EN/IEC 62040-2, EN/IEC 62040-3 and relevant IS standard. The system shall be true online double - conversion DSP based UPS system and also UPS shall be with automatic & manual bypass switch. The system shall have IGBT rectifier and inverter. 100kVA UPS System, 3 Phase, 415 Vac, 50 Hz - 3 Nos Inbuilt Isolation Transformer, 3 X 3, 100kVA, 3 Phase, 415V - 3 Nos Battery Rack Bolted Assembly, 2000W X 630 D X 1700 H, 5 Tier - 120AH for 38 Blocks - 144 Nos Kit Battery Cable Links , for 120 AH, 38 Blocks - 3 Nos Cable, NYVIN, 1 Core, Size 00, 660/1100V Grade - 3 Nos UPS Parallel Kit - 3 Nos for providing 15 Minutes Back up for each UPS and it shall be connected in single string with Battery Accessories like battery rack, interconnecting cables, battery isolators etc. Supply, installation, testing & commisioning
LIGHTNING & EARTHING PROTECTION :
LIGHTNING PROTECTION Supply, installation and tesing of 3 meter air terminal with accessories, providing and fixing air terminals as per IEC -62305 part-3 16mm rod tapered to 10 mm aluminium rod 4 meter rod: Meets the technical specification according to DIN EN 50164 - 2 (VDE 0815 part 202). Meets the requirement of VDE0185/305 (IEC 62305) 101 VL 4000: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) Suitable for high wind load. System consist of Fang Fix with base and clamp on the top air terminal is erected. Fang fix clamp made of cable bracket, lightning tested for 100 KA 10/350 micro sec waveform. 2 nos of 16 KG stone of 365 mm diameter, high level of stability. Quick and easy mounting of interception rod using anchors.Concrete, frost-resistant, can be stacked, including all accesories as required for complete installation as instructed by engineer in charge.
Supply and installation of 8mm solid aluminium round conductor: For concrete building Meets the technical specification according to DIN EN 50164-2 (VDE 0815 part 202). Meets the requirement of VDE0185/305(IEC 62305) RD 8/ALU: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) With 50 sq.mm cross sectional area. Polyamide Conductor holder: With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder. Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance, including all accesories as required for complete installation as instructed by engineer in charge. - a) Vertical run- Down conductor
Supply and installation of 8mm solid aluminium round conductor: For concrete building Meets the technical specification according to DIN EN 50164-2 (VDE 0815 part 202). Meets the requirement of VDE0185/305(IEC 62305) RD 8/ALU: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) With 50 sq.mm cross sectional area. Polyamide Conductor holder: With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder. Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance, including all accesories as required for complete installation as instructed by engineer in charge. - b) Horizontal run-Parapet application
Supply and installation of 8mm solid aluminium round conductor: For TERRACE APPLICATION Meets the technical specification according to DIN EN 50164-2 (VDE 0815 part 202). Meets the requirement of VDE0185/305(IEC 62305) RD 8/ALU: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) With 50 sq.mm cross sectional area. Stainless steel base with Polyamide Conductor holder top: Adjustable width from 185-260mm. Infinitely adjustable conductor holder. Fast installation using wing screw. Bottom section with 8.5mm diameter slot With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder. Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance
Supply and fixing of cross connector / T connector: to route vertical down conductor /mesh formation made of stainless steel/hot dipped galvanised iron with necessary screws etc as required. Installed with 4 hexagonal bolts M8*25 with M8 hexagonal nuts and all accesories as required for complete installation
Supply and fixing of expansion piece with connector: For equalising temperature related length changes. Necessary on conductors length over 20 meters. For round conductor Rd 8/ALU. Connector: For T cross and parallel connectors. Quick installation using hexagonal bolt M10X30 high-grade hot dip galvanised. Conforms to the requirements according to DIN VDE 0185-305 (IEC 62305) and all accesories as required for complete installation
Supply and Fixing Equipotential bonding rail for Lightning Arrestor applications (Test Joint). Equipotential bonding rail for equipotential bonding according to DIN VDE 0100-410/540 and lightning protection equipotetial bonding according to DIN VDE 0185-305. Base plate and cover hood from polystyrene. Colour: Black, UV resistant. Can be used outdoor also. Screw and crossbar made of VA. Capable of carring lightning current 100KA (10/350). Connection options: 7 x single or multi-core conductors to 25mm square or fine core conductors to 16mm square. 1 x round cable Rd 8-10. 1 x flat strip to FL 30 or round cable RD 8-10 including corrosion tapes and all accesories as required for complete installation as instructed by engineer in charge.
Supply and laying hot dip Galvanised Steel Flat having 70 microns zinc 30X3 mm thick from earth electrode directly in ground as required. Hot Dip GI strip, corrosion resistant. Cross sectional area of 90mm square According to DIN EN 50164-2 (VDE 0185 part 202) Meets the requirement of VDE0185/305(IEC 62305) Zinc coating: 500 g/m square (70 micron coating) Should be tested and use exclusively for lightning protection earthing system and ring equipotential bonding including cross connectors and all accesories as required for complete installation as instructed by engineer in charge.
Supply and fixing of PVC trapezoidal 1.5m long ducts including the fastening clamps and all accessories as required.
Providing and fixing of Cross connector for Flat: Suitable for 30mm Galvanised steel strip. Installed with 4 nos of hexagonal plate.
Supply, installation and testing of maintenance free Earthing system as per IS 2309 ,IEC 62305 part3, IEC 60364, IEC 62561 part 2, IS 3043, UL 467 & UL 96 standards. Earthing System comprises of molecularly bonded copper of 99.9% purity on low carbon steel of 3m length (1m (219 20 CU) x 3 nos), having a diameter of 20mm with copper coating thickness of 250 microns with self-coupling bore and peg arrangement (without the need for external coupler) with fault current withstand capability of 20 KA rms value for 1 second and I peak of 50 KA. For obtaining desired length, the number of rods shall be increased and is provided with Universal Clamp (2730 20 VA) made of SS 304 for clamping the cable/flat conductor to the rod. Impact point (219 20 IP) on the bottom rod for easy insertion. Earth enhancing mineral compound (ECS PB 12.5) is used for improving the soil conductivity. Earth enhancing mineral compound shall be so designed and constructed that in normal use their performance is reliable and without danger to persons and the surroundings. The material shall be mineral inert to sub soil and shall not pollute the environment. It shall provide a stable environment in terms of physical and chemical properties and exhibit low resistivity. It shall not be corrosive to the earth electrode itself. The material should have a resistivity less than 0.2 Ohm meter. It should be free from hazardous substances The mineral compound is required to have minimum 12.5 Kg of the total composite. Polypropylene & Polyethylene (UFE)Earth electrode inspection chamber with heavy duty cover should be used to cover the Earth Rod. The dimension shall be 170mmx 170mmx 190mm with a weight bearing capacity of 5KN, including all accesories as required for complete installation as instructed by engineer in charge.
EARTHING
Supply, installation and tesing of 1200mmx1200mmx12mm CI plate electrode earth station conforming to IS:3043-1987 / NEC / IEE complete with brick masonry chamber, CI cover, CI frame, GI watering pipe of 50 mm dia with funnel having 20G GI wire mesh etc. The CI cover frame/ chamber shall be of 1000mm x 500mm x 600mm size. CI manhole cover with frame shall be painted with bitumastic paint, identification of earthpit with yellow paint below the chamber cover, mixtures of charcoal & common salt around electrode including digging of pit up to permanent moisture level but not less than 3 metre depth and back filling. ( value of earth resistance should be less than 1 ohm )
Supply and laying the following sizes of Cu strips laid 0.6 m below ground level including excavating trench of suitable size and refilling, including necessary clamps and bolts etc and all accessories as required for complete installation as instructed by engineer in charge/consultant. : a) 25x3 Cu strips tinned at the joints
Supply and laying the following sizes of Cu strips laid 0.6 m below ground level including excavating trench of suitable size and refilling, including necessary clamps and bolts etc and all accessories as required for complete installation as instructed by engineer in charge/consultant. : b) 25x6 Cu strips tinned at the joints
Supply and laying the following sizes of Cu strips laid 0.6 m below ground level including excavating trench of suitable size and refilling, including necessary clamps and bolts etc and all accessories as required for complete installation as instructed by engineer in charge/consultant. : c) 32x3 Cu strips tinned at the joints
Supply and laying the following sizes of Cu strips laid 0.6 m below ground level including excavating trench of suitable size and refilling, including necessary clamps and bolts etc and all accessories as required for complete installation as instructed by engineer in charge/consultant. : d) 32x6 Cu strips tinned at the joints
Supply and laying the following sizes of earthing bare copper/strips on cable tray or wall surface, including necessary clamps (each clamp not exceeding 60 cm) and bolts etc as required for complete installation as instructed by engineer in charge/consultant. - a) 25x3 Cu strips tinned at the joints
Supply and laying the following sizes of earthing bare copper/strips on cable tray or wall surface, including necessary clamps (each clamp not exceeding 60 cm) and bolts etc as required for complete installation as instructed by engineer in charge/consultant. b) 25x6 Cu strips tinned at the joints
Supply and laying the following sizes of earthing bare copper/strips on cable tray or wall surface, including necessary clamps (each clamp not exceeding 60 cm) and bolts etc as required for complete installation as instructed by engineer in charge/consultant. c) 32x3 Cu strips tinned at the joints
Supply and laying the following sizes of earthing bare copper/strips on cable tray or wall surface, including necessary clamps (each clamp not exceeding 60 cm) and bolts etc as required for complete installation as instructed by engineer in charge/consultant. d) Copper wire No.10 SWG
Supply and laying the following sizes of earthing bare copper/strips on cable tray or wall surface, including necessary clamps (each clamp not exceeding 60 cm) and bolts etc as required for complete installation as instructed by engineer in charge/consultant. e) Copper wire No.8 SWG
RISING MAINS, BBT & TAP OFF BOXES
Supply, installation, testing and commissioning of following capacity type tested as per IEC 61439 Part 6, pre-fabricated Sandwich Type, epoxy insulated, compact, sandwitched indoor type (TPN) bus trunking on wall / ceiling / structure, with high conductivity aluminium conductor in convenient sections suitable for 3 phase 4 wire 50Hz, 415V, AC supply. The bus bar shall be complete with bends, expansion joints, fire barriers at wall/ceiling crossing, copper flexible end connections, elbows. The housing shall be constructed from 1.6mm (min) thick electro galvanised sheet steel enclosure, IP54 with epoxy coated. The busduct shall be complete with 4 nos aluminium busbar. Earthing with 2 runs of copper earth of size 25 x 5 mm copper strip (Cu strip shall go inside LT panels and end termination boxes) on each side including clamping bracket, angle iron bracket, steel fastners, connecting to earthing system etc as required, including supports for bus bars. The bus duct shall comply with IEC and BS standards. The routine test certificate as per IS / IEC and type test certificate of identical bus trunking shall be furnished. Rate shall be quoted for including bends, copper flexible, supports, hangers, flanged ends, adaptor box with terminal kits and all accesories required for complete installation. - 1000A Al TPN IP54 Feeder busduct
Supply, installation, testing and commissioning of following capacity type tested as per IEC 61439 Part 6, pre-fabricated Sandwich type, epoxy insulated, compact, sandwitched indoor type (TPN) rising mains on wall, with high conductivity aluminium conductor in convenient sections suitable for 3 phase 4 wire 50Hz, 415V, AC supply. The bus bar shall be complete with expansion joints, fire barriers at each floor crossing, copper flexible end connections. end cap etc . The housing shall be constructed from 1.6mm (min) thick electro galvanised sheet steel enclosure, IP54 with epoxy coated. The busduct shall be complete with 4 nos aluminium busbar. Earthing with 2 runs of copper earth of size 25 x 5 mm copper strip on each side including clamping bracket, angle iron bracket, steel fastners, connecting to earthing system etc as required, including supports for bus bars. The rising mains shall comply with IEC and BS standards. The routine test certificate as per IS / IEC and type test certificate of identical rising mains shall be furnished including all accesories required for complete installation. - a) 630A Al TPN IP54 Rising Mains
Supply, installation, testing and commissioning of following capacity type tested as per IEC 61439 Part 6, pre-fabricated Sandwich type, epoxy insulated, compact, sandwitched indoor type (TPN) rising mains on wall, with high conductivity aluminium conductor in convenient sections suitable for 3 phase 4 wire 50Hz, 415V, AC supply. The bus bar shall be complete with expansion joints, fire barriers at each floor crossing, copper flexible end connections. end cap etc . The housing shall be constructed from 1.6mm (min) thick electro galvanised sheet steel enclosure, IP54 with epoxy coated. The busduct shall be complete with 4 nos aluminium busbar. Earthing with 2 runs of copper earth of size 25 x 5 mm copper strip on each side including clamping bracket, angle iron bracket, steel fastners, connecting to earthing system etc as required, including supports for bus bars. The rising mains shall comply with IEC and BS standards. The routine test certificate as per IS / IEC and type test certificate of identical rising mains shall be furnished including all accesories required for complete installation. - b) 400A Al TPN IP54 Rising Mains
Supply, installing, connecting, testing and commissioning of following capacity end feed unit suitable for Sandwich type rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick electro galvanised steel sheet enclosure, IP54, complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. The end feed unit shall comply with IEC and BS standards. The routine test certificate as per IS / IEC and type test certificate of end feed unit shall be furnished. a) 630 Amp 36kA FP MCCB Thermal - Magnetic Release
Supply, installing, connecting, testing and commissioning of following capacity end feed unit suitable for Sandwich type rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick electro galvanised steel sheet enclosure, IP54, complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. The end feed unit shall comply with IEC and BS standards. The routine test certificate as per IS / IEC and type test certificate of end feed unit shall be furnished. b) 400 Amp 36kA FP MCCB, Thermal Magnetic Release
Supply, installing, connecting to existing sandwich rising mains, testing and commissioning of following capacity Plug in / Tap off box for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick electro galvanised steel sheet enclosure, IP54, with provision for and including thermal magnetic MCCB complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. The plug in / tap off unit shall comply with IEC and BS standards. The routine test certificate as per IS / IEC and type test certificate of complete plug in / tap off unit shall be furnished. a) 200 A 25kA FP MCCB in Tap off box
Supply, installing, connecting to existing sandwich rising mains, testing and commissioning of following capacity Plug in / Tap off box for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick electro galvanised steel sheet enclosure, IP54, with provision for and including thermal magnetic MCCB complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. The plug in / tap off unit shall comply with IEC and BS standards. The routine test certificate as per IS / IEC and type test certificate of complete plug in / tap off unit shall be furnished. b)160 A 25kA FP MCCB in Tap off box
Supply, installing, connecting to existing sandwich rising mains, testing and commissioning of following capacity Plug in / Tap off box for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick electro galvanised steel sheet enclosure, IP54, with provision for and including thermal magnetic MCCB complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. The plug in / tap off unit shall comply with IEC and BS standards. The routine test certificate as per IS / IEC and type test certificate of complete plug in / tap off unit shall be furnished. c) 100 A 25kA FP MCCB in Tap off box
Supply, installing, connecting to existing sandwich rising mains, testing and commissioning of following capacity Plug in / Tap off box for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick electro galvanised steel sheet enclosure, IP54, with provision for and including thermal magnetic MCCB complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. The plug in / tap off unit shall comply with IEC and BS standards. The routine test certificate as per IS / IEC and type test certificate of complete plug in / tap off unit shall be furnished. d) 80 A 25kA FP MCCB in Tap off box
Supply, installing, connecting to existing sandwich rising mains, testing and commissioning of following capacity Plug in / Tap off box for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick electro galvanised steel sheet enclosure, IP54, with provision for and including thermal magnetic MCCB complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. The plug in / tap off unit shall comply with IEC and BS standards. The routine test certificate as per IS / IEC and type test certificate of complete plug in / tap off unit shall be furnished. e) 63 A 25kA FP MCCB in Tap off box
SAFETY EQUIPMENTS
Supply and fixing of 4 Kg ABC Dry Powder (Stored Pressure) Type Fire Extinguisher. pressurized with dry nitrogen gas at 15 bar. Design, construction and testing as per IS 2171-1999 external epoxy powder coating with PO Red Shade No. 538 of IS 5, Supplied with standard accessories.
Supply and providing 2/3 mm thick sythetic type and 1 m wide electrical grade chequered type rubber mat to withstand 3.3 kV dielectric strength conforming to IS 5429/1969.
Supply and providing First Aid Box.
Supply and providing laminated First Aid chart duly framed and placed in a conspicuous location for clear vision.
Supply & fixing Laminated drawings of electrical lay out, schematic drawing etc on good frame work.
Supply and providing MS chequered plate of 6 mm thickness with MS supports including cutting, welding, painting etc. as required for cable duct covering etc.
Supplying and installing at approved location approved make fire buckets of 24 gauge galvanized steel sheet, standard 9 litre capacity and of round bottom shape, painted white inside and red outside and black on the bottom, inscribed with letters “FIRE” in black and gold or duly painted over a coat of primer. Cost inclusive of providing 3 Nos of fire buckes and MS stand frame.
Supply of 1 pair 11 KV rubber hand gloves of approved make.
Supply and providing 12 mm thick and 1 m wide electrical grade chequered type rubber mat to withstand 11 kV dielectric strength conforming to IS 5429/1969
ELV WORKS
DATA Information Outlet RJ 45 - Supply, fixing, fluke testing and commissioning of CAT6 Information Outlets (Key stone) with Shuttered Faceplate, Single port, white, jack, suitable PVC / GI Modular Box etc. including necessary connections with all accessories required for complete installation as directed by the Engineer in charge.
Information Outlet RJ 45 - Supply, fixing, fluke testing and commissioning of CAT 6A Information Outlets (Key stone) with Shuttered Faceplate, Single port, white, jack, suitable PVC / GI Modular Box etc. including necessary connections with all accessories required for complete installation as directed by the Engineer in charge.
CAT6 Cable - Supplying and drawing of Category 6 cable consists of 4 pairs of solid insulated copper 23AWG, surface/ recessed medium class PVC conduit through wall/tray with all accessories as required for complete installation and as instructed by engineer in charge/consultant and making good all damages made for installation.
CAT 6A Cable - Supplying and drawing of Category 6A cable consists of 4 pairs of solid insulated copper 23AWG, surface/ recessed medium class PVC conduit through wall/tray with all accessories as required for complete installation and as instructed by engineer in charge/consultant and making good all damages made for installation.
OFC Cable - Supplying and drawing of 6 core SM armoured Optical Fibre Cable (OFC) through wall/tray with all accessories as required for complete installation and as instructed by engineer in charge/consultant and making good all damages made for installation.
Patch Cable - User Side - Supply, fixing, testing and commissioning of CAT6 Patch Cable - 2 Meter length etc. of approved make as required for complete installation.
Patch Cable - Hub Side - Supply, fixing, testing and commissioning of CAT6 Patch Cable - 1 Meter of approved make as required for complete installation.
Patch Cable - User Side - Supply, fixing, testing and commissioning of CAT6A Patch Cable - 2 Meter length etc. of approved make as required for complete installation.
Patch Cable - Hub Side - Supply, fixing, testing and commissioning of CAT6A Patch Cable - 1 Meter of approved make as required for complete installation.
Patch Cable - Hub Side - Supply, fixing, testing and commissioning of Fibre Patch Cable - 2 Meter of approved make as required for complete installation.
Voice
Information Outlet RJ 11 - Supply, fixing, testing and commissioning of RJ11 Information Outlets (Key stone) with shuttered Faceplate, single port, white, jack, suitable PVC / GI Modular Box etc. including necessary connections with all accessories required for complete installation as directed by the Engineer in charge.
Cable - Supplying and drawing of following pair telephone cable consists of 0.5 mm dia FR, PVC Compound annealed copper conductor, unarmoured telephone cable in surface / recessed medium class FRS PVC conduit through wall/tray with all accessories as required for complete installation and as instructed by engineer in charge/consultant and making good all damages made for installation. 2 Pair Telephone Cable
Cable - Supplying and laying of following pair armoured telephone cable through wall/tray with all accessories as required for complete installation and as instructed by engineer in charge/consultant and making good all damages made for installation. - 10 Pair Telephone Cable
-do- 20 Pair Telephone Cable
-do- 50 Pair Telephone Cable
-do- 100 Pair Telephone Cable
krone Box - Supply, erection, testing and commissioning of following pair krone Box with mounting frame, enclosure of ISI grade with lockable front cover with all accessories required for fixing the box with all accessories required for complete installation in wall as directed by the Engineer in charge.- 10pair
-do- 20pair
-do- 50 pair
-do- 100 pair
-do- 150 Pair MDF Krone
Supply, installation, testing and commissioning of Basic user phone with necessary connection as required for complete installation as directed by the engineer in charge.
Surge Protection Device For EPABX: Supply, Installation, Testing and commissioning of SPD with enclosure, the surge protection device shall be suitable to protect telephone lines designed to with stand both lightning current and switching surges. Technology: GD tube, Nominal Voltage: 180 V, Pulsed Current (10/350 µs ) Iimp: 1 KA, Nominal Discharge Current (8/20 µs )/phase In: 5KA, Maximum discharge current: 10 KA,Voltage Protection Level(sym)<700V, Response time<1n sec
Closed Circuit Television (CCTV)
Camera for General Area - Dome - Supply, Installation, testing and commissioning of IP based 3.6 mm fixed lens, 2MP resolution, H.264 / H.265, 1/2.8" Progressive Scan CMOS Day/Night, IR dome POE enabled camera, 20 to 30 meters IR range, 120 dB digital WDR with all connectors and necessary accessories for mounting in false ceiling as required for complete installation as directed by Engineer in charge.
Camera for Lift - Dome - Supply, Installation, testing and commissioning of IP based 2.8 mm fixed lens, 2MP resolution, H.264 / H.265, 1/2.8" Progressive Scan CMOS Day/Night, IR dome POE enabled camera, 20 to 30 meters IR range, 120 dB digital WDR with all connectors and necessary accessories for mounting in false ceiling as required for complete installation as directed by Engineer in charge. PoE (Power over Ethernet)
Camera for Corridor - Dome - Supply, Installation, testing and commissioning of IP based 2.8/3.6 mm to 9/12 mm varifocal lens, 2MP resolution, H.264 / H.265, 1/2.8" Progressive Scan CMOS Day/Night, IR dome POE enabled camera, 20 to 30 meters IR range, 120 dB digital WDR with all connectors and necessary accessories for mounting in false ceiling as required for complete installation as directed by Engineer in charge. PoE (Power over Ethernet)
Camera - Bullet - Supply, Installation, testing and commissioning of Varifocal Bullet Camera with 2 MP, H.264 / H.265, built-in IR LED, 2.8/3.6 mm to 9/12 mm, 20 to 30 meters IR range, IP 66 with all connectors and necessary accessories for mounting in false ceiling/True Ceiling as required for complete installation as directed by Engineer in charge. PoE (Power over Ethernet)
Network Video Recorder with Storage: Supply, installation, testing and commissioning of Channel Network Video Recorder with Recording Storage space server for 30 days, Supports 64 channels 720 P resolution video recording at real time, NVR ONVIF supporting, Recording resolution of Max 4 MP, should support dual video HDMI output, H.265,H.264 at real time. Video storage expansion for recording for complete installation with all accessories as required and directed by engineer in charge. (Consider the sufficient HDDs for 720p @ 20 FPS for 30 days continues recording for all channels). Storage calculation details shall be submitted.
LED Display - Supply, installation, testing and commissioning of 43 inch full HD LED display for video wall arrangement for 24 x 7 Setup including necessary connection, HDMI cable, rating tray etc. as required for complete installation with all accessories as required and directed by engineer in charge. The
CAT6 Cable - Supplying and drawing of Category 6 cable consists of 4 pairs of solid insulated copper 23AWG, surface/ recessed medium class PVC conduit through wall/tray with all acessories as required for complete installation and as instructed by engineer in charge/consultant and making good all damages made for installation.
Supply, installation, testing and commissioning of workstation with Intel I5 or above, 4 GB ram and 1 TB HDD with software for CCTV integration
Public Addressing System (PAS)
Ceiling Mounted Speaker - Supply, fixing, testing and commissioning of ceiling mount Metal Grille Speakers with inbuilt line matching transformer with power 6W with required accessories for installation as required.
Wall Mounted Speaker - Supply, fixing, testing and commissioning of Cabinet Speakers with inbuilt line matching transformer with power 12W with a volume controller to adjust the volume individually as per the requirement with all accessories for complete installation as required. The volume controller shall be fixed separately as per the site condition for individual control. Cost inclusive of necessary interconnection including conduit, connection wire etc required for complete installation.
Mixing Amplifier - Supply, fixing, testing and commissioning of 240 Watts Mixer Amplifier with necessary jacks and cable for connections and interconnection with all accessories required for installation as required.
Power Amplifier - Supply, fixing, testing and commissioning of Power Amplifier of 480 Watts with necessary jacks and cable for connections and interconnection with all accessories required for installation as required.
Controller - Supply, fixing, testing and commissioning of Master zone controller with routing zone capacity of additional 6 zones with all accessories and necessary connections including necessary cables and jacks as required for complete installation. The work also include integration with Fire Alarm System (FAS) including to play the pre-recorded message in case of fire and evacuation.
Call Stations - Supply, fixing, testing and commissioning of 6 Zone Calling Station with mic as per the drawing as required for complete installation.
Audio/Video player - Supply, installation, testing & commissioning of Audio/Video player with USB option with all accessories like jacks and codes for complete installation as required as directed by the Engineer in charge.
Speaker Cable - Supplying and drawing of 2 Core, Twin Twisted, ATC tinned copper, overall sheathed, Armoured Speaker cable, 16 AWG for speakers through surface / Tray with all accessories as required for complete installation and as instructed by engineer in charge/consultant and making good all damages made for installation.
Active Components, Racks & Accessories
Supply, Installation, Testing and installation of Cat - 6, shuttered type, 24 port fully loaded patch panel with necessary cable manager for routing the cable inside rack with all accessories required for complete installation as required as directed by the engineer in charge.
Supply, Installation, Testing and installation of Cat - 6, 24 port 10/100/1000 Mbps, layer 2, POE, switch with rack mounting brackets, input connector shall be as per IEC-320-C14 with all accessories required for complete installation populated with 1G single SFP module for uplink as required as directed by the engineer in charge. The switch should be capable to provide sufficient power budget to IP cameras as per the requirement.
Supply, Installation, Testing and installation of 6 port Light Interface Unit (LIU) / Fibre Patch Panel, rack mountable with mounting brackets, loaded with Adaptors, Couplers Single Mode (SM) pigtails with splicing with all accessories required for complete installation as required as directed by the engineer in charge.
Supply, Installation, Testing and installation of Cat - 6, 24 port Layer 3 Managable Core switch with rack mounting brackets, input connector shall be as per IEC-320-C14 with all accessories required for complete installation populated with 1G single SFP module as required as directed by the engineer in charge.
Supply, installation, testing and commissioning of 4U Rack with Front glass door, Rear Perforated door with handle Lock & key. Front/Rear 4U mounting angles, top, bottom open, RAL 9005, including necessary exhaust/circulation fan with all accessories required for complete installation as directed by the engineer in charge.
Supply, installation, testing and commissioning of 12U Rack with Front glass door, Rear Perforated door with handle Lock & key. Front/Rear 12U mounting angles, top, bottom open, RAL 9005, including necessary exhaust / circulation fan with all other accessories required for complete installation as directed by the engineer in charge.
Supply, installation, testing and commissioning of 42U Rack DK_PS frame with Front glass door, Rear Perforated door with handle Lock & key, castors. Side and rear panels, Front / Rear 42U 800Wx1000D MM mounting angles, top, bottom open, RAL 9005, including necessary exhaust / circulation fan with all other accessories required for complete installation as directed by the engineer in charge.
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections including tees, bends, cross sections etc required for complete installation as per the requirement joined with connectors, suspended from the ceiling with G.I. suspenders including GI bolts & nuts, etc. as required for complete installation as directed by the engineer in charge. (For Data, Voice, CCTV & PA) - 100 mm width X 50 mm depth X 1.6 mm thickness
-do - 150 mm width X 50 mm depth X 1.6 mm thickness
FIRE FIGHTING WORKS - FIRE PUMPS AND ACCESSORIES
MAIN PUMP - Supply, installation, testing and commissioning of Horizontal long coupled End Suction Fire Hydrant Pump Set: Electrical Driven, Capacity: 2280 LPM at 90 Meter Head, conforming to IS 1520, with Bronze Impeller, S. S. Shaft, Mechanical Seal, High Efficient IE-3 rated, Squirrel Cage Induction Electric Motor, Suitable HP, 3Ph, 50 Hz, 2900/3000 RPM, TEFC, complete with necessary concrete foundation duly plastered, MS fabricated common base plate with foundation bolts, compound gauge, water re-circulation arrangement, pressure relief valve, anti-vibration mounts, as per requirement and nececssary earthing of Electric Motors, etc. all as per the Technical Specifications, Prevailing Rules, Standards, Requirement and Site Conditions.
SPRINKLER PUMP - Supply, installation, testing and commissioning of Horizontal long coupled End Suction Fire Sprinkler Pump Set: Electrical Driven, Capacity: 2280 LPM at 90 Meter Head, conforming to IS 1520, with Bronze Impeller, S. S. Shaft, Mechanical Seal, High Efficient IE-3 rated, Squirrel Cage Induction Electric Motor, Suitable HP, 3Ph, 50 Hz, 2900/3000 RPM, TEFC, complete with necessary concrete foundation duly plastered, MS fabricated common base plate with foundation bolts, compound gauge, water re-circulation arrangement, pressure relief valve, anti-vibration mounts, as per requirement and nececssary earthing of Electric Motors, etc. all as per the Technical Specifications, Prevailing Rules, Standards, Requirement and Site Conditions.
JOCKEY PUMP - Supply, installation, testing and commissioning of Jockey Pump: Electrical Driven, Capacity: 180 LPM at 95 Mtrs. Head, Vertical Multi Stage Inline Pump with S.S Impeller, Mechanical Seal, and with High Efficient IE-3 Rated Squirrel Gauge Induction Motor, Suitable HP, 3Ph, 50 Hz, 3000 RPM, TEFC, complete with necessary concrete foundation duly plastered, MS fabricated common base plate with foundation bolts, compound gauge, water re-circulation arrangement, pressure relief valve, anti-vibration mounts, as per requirement and nececssary earthing of Electric Motors, etc. all as per the Technical Specifications, Prevailing Rules, Standards, Requirement and Site Conditions.
DIESEL PUMP - Supply, installation, testing and commissioning of Stand By / Back Up Fire Pump, Horizontal long coupled, End Suction Pump, Engine Driven, suitable for Automatic operation and consisting of the following and complete in all respect as required; Capacity: 2280 LPM at 90 Meter Head conforming to IS 1520, with Bronze Impeller, S. S. Shaft, Mechanical Seal, coupled to High Efficient Radiator Cooled Diesel Engine, Suitable HP, 2150 RPM, and with Control Panel with Auto Starting Facility, by activation of concerned Pressure Switch and thro. 12V/24 V Electric Starter, Battery of adequate rating and with Battery Charger, Battery Leads, Diesel Tank for 6 hrs operation, exhaust pipe extended up to 1 mtr outside pump house, duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per specification, complete with necessary civil foundation, foundation bolts, compound gauge, water re-circulation arrangement, pressure relief valve, and all other necessary fixing accessories, all as per Technical Specifications.
Supply, erection, commissioning of additional length of Exhaust Pipes with long radius bend from silencer with necessary clamps, fixtures, civil works andthermal insulation with 50 mm thick glass wool and with 1.0 mm thick aluminium sheet cladding of following adequate size including suitable rain cap for top to avoid rain water entry. The distance between exhaust pipe at top and rain cap should be higher than diameter of pipe. The horizontal run of exhaust piping should slope downwards away from engine to the condensate trap. Silencer should be installed with drain plug at bottom. Fixing shall be done with proper clamps, expansion bolts, and all other acessories as instructed by the Engineer and the rate inclusive of all minor civil works required, bolts, clamps etc as required for istallation. Support to exhaust piping should be done in such a manner that load of exhaust piping is not exerted to turbocharger. Exhaust pipe height shall be 3m more than the top of any adjacent building withing 10m radius of the exhaust.
LT CABLE SUPPLY - Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (Part 1) ammended upto date. - 3CX185 Sqmm A2XFY Cable
-do- 3CX6 Sqmm A2XFY Cable
MV CABLE LAYING - Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on wall surface / Tray as required. - Above 35 sq. mm and upto 95 sq. mm (Clamped with 25X3mm MS flat clamp)
MV CABLE JOINTING & END TERMINATION - Supplying and making end termination with brass double compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. - 3CX185 Sqmm A2XFY Cable
-do- 3CX6 Sqmm A2XFY Cable
Supply, installation, testing and commissioning of Pressure Switches with pressure rating suitable for Fire Pumps, with a differential of 0.2 to 1.6 Bar, as per Technical Specifications.
Supply, installation, testing and commissioning of Diaphragm Pressure Vessel, 112 Ltrs Capacity, 15 Bar Working Pressure at a maximum flow rate of 2280 LPM. The vessel shall be with replaceable interior air cell, metallic outer shell, base, air release valve etc, all as per Technical Specifications.
FIRE HOSE REEL & HYDRANT SYSTEMS
Supply, installation, testing and commissioning of Manual Swing Type Fire Hose Reel Complete Set with heavy duty drum / reel, 19mm. dia. x 30Mtr. long 2-ply polyester yarn braided / rubber braided pressure hose, Red Coloured, heavy duty nylon on/off jet/spray nozzle, 22mm. isolating valve and all other necessary fixing accessories including Fabrication and Erection of M.S. Support, as per requirement, for Fixing the Fire Hose Reel Set.
Supply, installation, testing and commissioning of Fire Hydrant Valve, bearing to ISI:5290 Type-A mark, Stainless Steel-304 body with 63mm. oblique instantaneous single outlet, 75mm. N.B. flanged inlet, Stainless Steel -304 spindle, complete with PVC blank cap, G.I. chain etc.
Supply, installation, testing and commissioning of Fire Brigade Inlet Breeching, C.I. body, having 3 Gunmetal, 63mm. male instantaneous inlet, conforming to IS: 903, with non return valves, 25mm. drain valve, flanged outlet, 3 nos. of rubber blank caps and G.I. chains.
Supply, installation, testing and commissioning of Fire Brigade Draw Off Outlet C.I. body, having 3 Gunmetal, 63mm. female instantaneous inlet, conforming to IS: 903, with non return valves, 25mm. drain valve, flanged outlet, 3 nos. of rubber blank caps and G.I. chains.
Supply, installation, testing and commissioning of Fire Hose, RRL hose jacketed with circular woven synthetic fiber. conforming to IS: 636:88, with Working Pressure 14 Kg/Cm2, Proof Pressure 22 Kg / Cm2 and Burst Pressure 38 Kg / Cm2. The Fire Hose shall be with IS: 636 Type-A marking and 63mm. dia. x 15 Meter long with pair of 63mm. male and female instantaneous couplings, Stainless steel - 304, having IS: 903 mark and duly S. S. wire wounded. The hose shall be rolled and hung to suitable M. S. support in the Fire Station.
Supply, installation, testing and commissioning of Branch Pipe, Stainless Steel-304, short type, with 63mm. male instantaneous inlet, male threaded outlet, fitted with 16mm. bore nozzle, having IS: 903 mark.
Supply and fix at site in position Fire Hose Cabinet, wall / pole mounting type, 30” x 24” x 10” size, to accommodate two 15m length of delivery hose and branch pipe, acrylic fronted double door, with lock, 2 keys and a break glass recess for keys, painted Fire Red. The price shall be inclusive of fixing accessories and as per requirement.
Supply and fix at site in position Weather Proof Fire Hose Cabinet, wall / pole mounting type, 30” x 24” x 10” size, to accommodate two 15m length of delivery hose and branch pipe, acrylic fronted double door, with lock, 2 keys and a break glass recess for keys, painted Fire Red. The price shall be inclusive of fixing accessories and pole for mounting, all as per requirement.
AUTOMATIC FIRE SPRINKLER SYSTEM
Providing, fixing, testing and commissioning of Standard Coverage, Quick Response Automatic Fire Sprinkler, K- Factor: 5.6 (80 Metric) or equal to the approval of system consultant / engineer - in - charge, with necessary accessories and fittings. - Upright Type, 68 Degree C Rating.
-do- Pendant Type, 68 Degree C Rating.
-do- Pendant Type, 79 Degree C Rating.
Providing, fixing, testing and commissioning of Extended Coverage, Quick Response Horizontal Side Wall Type Automatic Fire Sprinkler, 68 degree, K- Factor: 5.6 with necessary accessories and fittings. The Fire Sprinklers shall be UL listed.
Supply for Stock : Supply of Standard Coverage, Quick Response Automatic Fire Sprinkler, K- Factor: 5.6 (80 Metric) or equal to the approval of system consultant / engineer - in - charge, with necessary accessories and fittings. - Upright Type, 68 Degree C Rating.
-do- Pendant Type, 68/79 Degree C Rating.
Supply for Stock : Providing, fixing, testing and commissioning of Extended Coverage , Quick Response Horizontal Side Wall Type Automatic Fire Sprinkler, 68 degree, K- Factor: 5.6 with necessary accessories and fittings. The Fire Sprinklers shall be UL listed and FM Approved
Providing & Fixing 2 Piece Chrome Plated Friction Fit recessed escutcheon for pendant sprinklers, as per requirement.
Providing, Fixing, Testing and Commission Flexible Sprinkler Hose; UL Listed, FM Approved, 25mm. (1") BSP Male Inlet, 15mm. (1/2") NPT Female Outlet, Braided, Working Pressure 13.8 Bar, length: 1000 mm, and with all connecting systems and accessories.
Providing, Fixing, testing and commissioning of Flow Switch, Vane type, IP 65 Protection with 20 Bar Working Pressure Protection with all necessary accessories, for monitoring Fire Sprinkler System. The control cabling from flow switches to Fire Sprinkler Annunciating Panel shall be measured separately.
FIRE PIPES, VALVES & ACCESSORIES
Hydrant, Sprinkler System & Plant Room : Providing, fixing, pressure testing and commissioning of Above Ground Fire Line Pipe Work with Heavy Duty (Class-C) Galvanized Steel Pipes, confirming to IS: 3589/1239 Part - I and with Heavy Duty Galvanized Ductile Iron Screwed Fittings for Pipes up to 50mm diameter and Galvanized Grooved Fittings, for pipes above 50mm. dia, for pump room But Welded fittings with all accessories required for complete installation such as tees, elbows, reducers, check nuts, unions, flanges, nipples and neoprene gasket, bolts, nuts, washers etc. including cutting, threading, grooving, joining, fixing in ducts, on walls, ceiling etc. by using suitable and strong enough supports, as per requirement, providing higher sizes of Sleeves/Opening, wherever required, and closing the gap between the pipes and sleeves/openings with 2 Hr. Fire Rated compound / sealant to the approval of Engineer - in - Charge /Consultant. The total pipe work shall be protected with approved painting system as per technical specification. All Pipe Fittings shall be UL Listed and FM Approved, as per the technical specification.
Providing, fixing, pressure testing and commissioning of Under Ground Fire Hydrant Pipe Work with Ductile Iron Pipes conforming to IS: 8239 / BIS EN: 545, Working Pressure 16 Bar (Class K-9), with Socket and Spigot joint. Pipe Fitting shall of Class K12. All the Pipes and Fittings shall with following protective coats / lining as per Standards and Manufacturer’s technical details. i. Internal lining with Cement Mortar ii. External Coating with a layer of metallic zinc + a layer of bitumen coating. iii. Further protection with loose & air / water tight polythene sleeves. The cost for underground pipe work shall inclusive of earth work excavation and refiling & compacting of soil after laying the pipe including necessary Masonary / PCC / RCC Thrust Blocks as per requirement. : 80 mm.
Providing, fixing, testing and commissioning of Forged Ball Valve, PN-16 or above gunmetal /cast alloy, confirming to IS 13114 including necessary accessories and connections. - 25 mm.
Providing, fixing, testing and commissioning of Butterfly Valve, PN-16 or Above, Slim seal, standard lever operated type confirming to BS:5155 with IS: 13095 Mark, with required companion flanges, nuts, bolts etc. complete, all as per Technical Specifications. - 65mm.
Providing, fixing, testing and commissioning of Butterfly Valve, Wafer Type, PN-16 or Above, Gear / Lever Operated (as per manufacturer) confirming to ASTM A-536, grade 65-45-12, with Micro / Tamper switch and Position Indicator UL Listed & FM Approved, with required Matching Flanges, nuts, bolts etc. complete, all as per Technical Specifications. - 100mm.
Providing, fixing, testing and commissioning of Non Return Valve, Wafer Swing Check type, PN-16 or Above, conforming to IS: 5312 part 1 with required companion flanges nuts, bolts etc. complete. - 50mm.
Supply, installation, testing and commissioning of Heavy Duty Neoprene Expansion Joints / Flexible Connectors, PN:16 or Above, with Spilt Retainer Rings and Control Units, drilled to BS 10 Table E including all other necessary fixing accessories. - 50mm.
Supply, installation, testing and commissioning of Hydraulically Operated Fire Sprinkler Alarm Valve (Installation Control Valve), Grooved End, UL Listed / FM approved, complete with Constant Pressure Trim Assembly, Water Motor Gong, control valves, pressure switch, pressure gauges etc. including all necessary fixing accessories. - 200mm. Size
Supply, installation, testing and commissioning of Air Release Valve Gunmetal, conforming to IS 904, having rubber ball with sealing seat and with 25mm. BSP threaded male inlet, including necessary accessories and connections.
Providing and fixing C. I. Gate Valve with Non Rising Stem & Cap Top, PN-16 or above, confirming to IS: 14846 with ISI Mark and with required companion flanges, rubber insertions, bolts, nuts, washers etc. complete. The Price shall be inclusive of ‘Fabricated Key' for Operation the Valve from Ground Level, all as per Technical Specifications. - 80mm.
Providing and fixing Ductile Iron Gate Valve, Rising Spindle, OS & Y Type, Body: ASTM A536, 65-45-12, Flanged to BS5163, PN16, UL Listed & FM Approved with Tamper / Supervisory Switches and with required flanges, rubber insertions, bolts, nuts, Washers etc. complete. - 200mm.
Supply, installation, testing and commissioning of 4" dia. Bourdon Type Pressure Gauge, with ISI Mark or of equivalent International Standards. : Weather / Water Proof Type with connection Pipe
Supply, installation, testing and commissioning of 4" dia. Bourdon Type Pressure Gauge, with ISI Mark or of equivalent International Standards. : Standard Type for indoor use with connection Pipe
INTELLIGENT ADDRESSABLE FIRE ALARM SYSTEM
FACP - Supply, install, test and commission Intelligent Addressable Fire Alarm Control Panel (FACP) as per the technical specification and not limited to having Visual Display Unit (VDU) preferably 640 character LCD display with Battery Back up for 24 hours for normal operation and 1 hours on alarm condition. The system shall be UL listed approved. The panel shall work in a flash scan protocol and shall be networked together and capable of networking with other compatible panels. The Panel shall have 10 Loop Capacity and shall be expandable, all as per Technical Specifications.
FAMP - Supply, install, test and commission Intelligent Addressable Fire Alarm Monitoring Panel (FAMP) as per the technical specification and not limited to having Visual Display Unit (VDU) preferably 640 character LCD display.
Providing, fixing test and commission Intelligent Addressable Manual Call Station Point with addressable module that monitors and reports contact status, all as per technical Specifications. The MCP shall be UL Listed and FM Approved
Providing, fixing, test and commission Intelligent Addressable Weather/Water Proof/Corrosion Resistant type Intelligent Addressable Manual Call Point having an integrally mounted addressable module that monitors and reports contact status, IP67 rated, complete as per technical specifications. The MCP shall be UL Listed and FM Approved
Providing, fixing, test and commission Conventional Type Horn/Strobe rated at 82 dB @ 3Mtr. for audible annunciation and 75 Candela flashing at 1Hz. for visual indication, complete as per technical specifications.
Providing, fixing, testing and commission Weather/Water Proof/ Corrosion Resistant Conventional Type Horn/Strobe, Rated at 82 dB @3Mtr. for audible annunciation and 75Candela flashing at 1Hz. for visual indication, IP: 66 Rated, complete as per technical specifications.
Providing, fixing, testing and commission Intelligent Addressable Input/Monitor Module, as per specification for interface with Flow Switches, Fire Pumps, Supervisory Switches, Alarm Valve, Water Tank Level etc.
Providing, fixing, test and commission Intelligent Addressable Control Module, as per specification for interface with Fire Alarm Annunciating System, Lift Panel etc. The Module shall be UL Listed and FM Approved.
Providing, fixing, testing and commission Intelligent Addressable Relay Module, as per specification for interface with Water Curtain Partition, AHUs, Ventilation System, Smoke Management System, Power Distribution, Public Address System etc. The Module shall be UL Listed and FM Approved.
Providing, fixing, test and commission Intelligent Addressable Fault Isolator Module capable of monitoring shorted loop circuit and automatically restore communications when shorted conditions are corrected, all as per technical specifications. The Module shall be UL Listed and FM Approved.
Providing, fixing / laying, test and commission 2 Core x 1.5 mm2 FRLS Armored Cables with Red Colour / Finish, as per Technical Specifications.
Providing, laying, test and commission 2 Core x 1.5 mm2 FRLS Armoured Cables, Underground laid in Trenches, all as per Technical Specifications. Cost for connected civil Work / Trenches shall measured and accounted separately.
FIRE EXTINGUISHERS
Providing, fixing, commission and install in position following Portable Fire Extinguisher as per BIS 2190 and BIS: 15683:2006 including necessary SS supports with all accessories for fixing the extinguisher in position and with relevant ISI Stamping/Marking. - CO2 - 2.0 Kg.
-do -CO2 - 4.5Kg.
-do -ABC Dry Chemical, Store Pressure Type - 2 Kg.
-do -ABC Dry Chemical, Store Pressure Type - 4 Kg.
-do -Water CO2, Cartridge Type - 9 Ltr.
-do -Foam Type, Cartridge Type, 9 Ltrs. (For DG Set.)
-do -Fire Bucket including Fabricated M. S. Stand
TALK BACK SYSTEM
Supply, installation, testing and commisioning of Public Address speaker with talk back facility 6 Watts with L M T and call switch, made out of powder coated CRCA sheet, wall mounting type and to be installed at a height of not less than 150 CM from the finished floor levels, suitable for concealed mounting.
SIGNAGES
Fire Exit Light - Laser type, with High Glow LED Light, size: 12” x 6” or nearby, Ceiling Mounting type with hanging clamps, on/off switch, Red / Green Colour option, power consumption: 18 Watt or less with all accessories required for complete installation as directed by the engineer inc charge. Power supply shaould be provided with UPS back-up.
Signage Printed "IN CASE OF FIRE, USE STAIRS UNLESS INSTRUCTED OTHERWISE" of 1.25cm. height letters in red with white back ground. The size of the board shall be 25 x 30 Cm. and shall be fixed at the height of 2Mts. from finished floor near Manual Pull Stations.
Floor Identification Signage (ie, GROUND FLOOR, FIRST FLOOR, etc.) at each stair enclosure on every floor, indicating the floor number in words, lettering size shall be 5 Cm. with contrasting colour from back ground. Size shall be 15cm x 30cm.
Floor Identification Signage (MAIN STAIRCASE, FIRE STAIRCASE, FIRE ASSEMBLY POINT, PUMP ROOM, FIRE CONTROL ROOM, ELECTRICAL ROOM, FIRE LIFT, PASSENGER LIFT Etc.) at each stair enclosure on every floor, indicating the floor number in words, lettering size shall be 5 Cm. with contrasting colour from back ground. Size shall be 15cm x 30cm.
Supply and install in position the Signage "FIRE ORDER" it should contain the matter specified in the technical details on 3mm thick "Opaque" PVC foam board of computerized cut, PVC non-reflective self adhesive vinyl painted foam board of 2' x 3'.
EXTERNAL (CIVIL) WORK
Constructing masonry Valve Chamber in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice / gate valve, including all supports for fixing valve, with Heavy Duty C.I. cover and frame, i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design. - Internal Size: 60 x 60 x 75cm, deep
-do- Internal Size: 90 x 90 x 100cm, deep
MISCELLANEOUS ITEMS
FIRE SEALANT for all Shafts - Supply and Fixing of load bearing Fire stop mortar CP 636 or equivalent system with minimum 2 hours fire rating when tested in accordance with UL 1479 standards, for openings in floors or slabs after passing service lines. The mortar shall be a light weight cementitious product and shall carry test certificate in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. The product shall be age tested as per Dafstb and DIBT standards. The product shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96 and shall have a VOC content of approx. <1 g/l as per LEED 2009. Firestop installation should be done by trained applicators (HAFSC) and in accordance with manufacturer's guidelines by providing 10mm dia rebars at 200mm c/c both ways with chemical anchoring along the length and breadh of the shaft and provide 2 layers of chicken mesh etc. The mortar shall be applied with a minimum thickness of 65 mm & having load bearing capacity of 200kg/sqm. Proper engineering judgement needs to be submitted through the manufacturer. Complete installation report through Software CFS DM shall also be submitted for inspection purpose.
FIRE SEALANT for HVAC / MGPS Shafts - Providing Acrylic Firestop Sealant Hilti CP 606 in gaps between periphery of the ducts to provide minimum 2 hours fire rating when subject to the test conditions of UL 2079 standards. The product shall be age tested as per DafStb guidelines. Sealant should provide sufficient MAF, water and gas tight seal. Sealant shall also provide airborne sound transmission reduction (STC of 50) and shall be tested as per DIN 52210 for sound insulation. Sealant shall carry test certificate for mold resistance rating of 0 as determined by ASTM G21-96 and should have a VOC content of approx. 75 g/l as per LEED 2009. The sealant shall carry test certificate in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. The product shall be UL listed & classified and shall bear the UL and FM approval logo on the packing. Firestop installation should be done by trained applicator (HAFSC) and in accordance with Hilti guidelines. Applicator needs to provide complete installation report through Software CFS DM for inspection purpose.
FIRE SEALANT for Electrical / ELV / FAS Shafts - Providing High performance intumescent firestop sealant FS One Max that helps protect combustible penetrations for up to 2 hours fire rating in accordance to UL 1479 (American) standards. Surface burning characteristics according UL 723 (ASTM E84-96). Flame spread index 0 and smoke development index 5. The sound transmission classification for this product according ASTM E 90-99 is 56 (STC Rating). It High is mold and mildew resistant and the performance is Class 0 according ASTM G-21. Movement capability approx. 5% (ISO 11600) and the average volume shrinkage is 24% according ASTM C1241. The sealent shall meets LEED requirements for indoor environmental quality credit (4.1 and 4.2) with a VOC content of 9 g/l. product should also Seismic tested on mechanical performance, smoke and fire-ratings. Firestop installation should be done by trained applicators (HAFSC) and in accordance with Hilti guidelines. Applicator needs to provide complete installation report through Software CFS DM for inspection purpose.
Fabrication, supply, installation at site Heavy Duty Galvanized Mild Steel Puddle Flange, Fabricated from Heavy Grade M. S. Pipe, confirming to IS: 1239/ 3589, with PN:20 Drilled M.S. Flange (s), as per Table BS-10 and M.S. Plate, all as per tender drawings and technical specifications, provided. After total fabrication, the puddle flange should be hot dipped galvanized to IS: 4759 and further protected with Epoxy Coating to the approval of the Engineer - in - charge and Consultant. Length of Puddle Flanges, shown, below are tentative only. The actual lengths may change as per final site conditions. - 100mm.dia, 1050mm. Long.
-do - 150mm.dia, 700mm. Long.
-do - 200mm.dia, 700mm. Long.
-do - 250mm.dia, 1050 mm. Long.
HVAC WORKS - WATER CHILLING PLANT
Supply at site including local transport with full cover insurance, fire or any other contigencies, unload, store, handle, erect, balance, test and commission the entire water chilling plant as per specifications including all accessories as specified for water chilling plant. WATER COOLED TWIN SCREW CHILLER - (R-134A/410) EACH WITH SEMI SEALED / SEALED, SINGLE / MULTIPLE COMPRESSOR OF MINIMUM CAPACITY 90 TR. Minimum Overall Chiller efficiency offered shall have COP ≥ 5.1 AS PER ECBC / ASHRAE / ARI 550/590 Summer Ambient conditions: DBT – 95 deg F, WBT- 82 Deg F Comprising of Screw Compressor as per specifications. Drive motors of suitable ratings 415+/- 10% Volts 50 Hz AC supply and starter panel with soft/star-delta/double delta starter. Water cooled condensor with all accessories. Automatic capacity control unit to regulate the capacity down to 30%. Micro-processor control panel. Building management system compatible software Data Link / Micro Gateway for integration with third -party BMS on Modbus / BACNET protocol, Safety controls as per spec. wiring and interlock between pumps shall be included in the chiller cost. The cost for additional incoming metering panel for each chiller to be included in the chiller. Water cooled chiller with all accessories: LOT-integral mounting frame for all the components, LOT-refrigerant piping & valves, LOT-insulation of chiller and suction line, LOT-first charge of refrigerant and lube oil, LOT-vibration isolation pads. LOT-Thermometer for water inlet and outlet and water flow switches. (complete specification as detailed in Part C - Schedule of Quantities)
PUMPS & COOLING TOWER
Supply, installation, testing & commissioning the chilled water primary pumps as per specification including all accessories as specified and as required. Including Factory made base frame & fixing foundation with necessary fittings as required Endsuction Chilled water Pump sets complete with TEFC sq.cage induction motor (WITH MECHANICAL SEAL) stainless steel shaft, bronze impeller, base plate couplings, pressure gauges (2 Nos. with syphon and gauge cock, anti vibration springs. guards etc. including insulation as per specifications: Capacity : 216 USgpm, 1440rpm Head : 45 feet Motor : 5 H.P (Suggested) - IE 3
Supply, installation, testing & commissioning the chilled water secondary pumps as per specification including all accessories as specified and as required. Including Factory made base frame & fixing foundation with necessary fittings as required Endsuction Chilled water Pump sets complete with TEFC sq.cage induction motor (WITH MECHANICAL SEAL) stainless steel shaft, bronze impeller, base plate couplings, pressure gauges (2 Nos. with syphon and gauge cock, anti vibration springs. guards etc. including insulation as per specifications: Capacity : 216 USgpm, 1440rpm Head : 90 feet Motor : 7.5 H.P (suggested) - IE 3
Supply, Installation, testing & commsssioning the condenser water pumps as per specification including all accessories as specified and as required. Including Factory made base frame & fixing foundation with necessary fittings as required. Endsuction Chilled water Pump sets complete with TEFC sq.cage induction motor (WITH MECHANICAL SEAL) stainless steel shaft, bronze impeller, base plate couplings, pressure gauges (2 Nos. with syphon and gauge cock, anti vibration springs. guards etc. including insulation as per specifications: Capacity : 360 USgpm, 1440rpm Head : 60 feet Motor : 10 H.P (suggested) - IE 3
Supply, Installation, testing & commissioning the cooling towers as per specification including all accessories as specified and as required. COOLING TOWERS of actual capacity complete in all respects as per technical specifications and equipment schedule complete with FRP casing, FRP fan cylinder, PVC louvers, PVC drift eliminator polypropelene nozzles, drive assembly, HDG fan guard/bird screen, non-clogging nozzle type water distribution system. PVC fill, aluminium ladder with railings, make up water, quick fill and drain over flow connections with valves & fittings etc. as per specifications. Including R.C.C foundation along with PCC/RCC sub base, fixing with bolts and nuts and finishing the slabs or any opening etc. 90 TR - CTI/JCI approved induced draft, cross flow cooling tower with vertical air discharge. EWT = 97.5 degree F LWT = 90 degree F WET bulb = 82 degree F Flow rate = 360 USgpm Motor suggested - 5 HP, IE 3
DOUBLE SKIN AIR-HANDLING UNITS WITH VFD & PLUG FANS and THERMAL BREAK
Supply, Installation, testing & commissioning the following Air Handling Units as per specification including all accessories as specified and as required for complete installation. The cost inclusive of VFD starter panel in a seprate enclosure with necessary rating incomer isolator / MCCB /contactor with all accessories including necessary connections, inter connnections and control wiring with pressure sensors (minimum 2 Nos.) for complete instation. Only HVAC application VFD's shall be used. All AHU’s will be given only one power input cable. Any looping should be done by OEM in case of multiple motors in one AHU. AHU shall be Pre-Plasticised Sheet/powder coated, Extruded Aluminium penta post frame work, Fan section, coil section, filter section, with necessary insulations, drain pan, etc. Cooling coil of copper tubes and aluminium fins (min. 10 fins per inch) and required number of rows deep. IE-3 efficiency TEFC sq.cage induction motor of required rating including mounting and fixing arrangements. Plug fan with VFD Drives anti vibration springs/isolator bearings etc. 10 mm thick synthetic media filter with frame. 90% efficiency down to 20 micron. Insulation of all section with fire retardant insulation material as per manufactures standard. Air vent on cooling coil with globe valve/screwed plugs. Insulation of Drain pan as per specifications. Double canvas connections of fire retardant quality for connecting AHU's to ducting/plenum. Insulated drain piping with trap till the out let of the AHU. Balance will be measured in the chilled water piping. Thermostat, Thermowell at the inlet and outlet of cooling coils, gauge cocks at the the inlete and outlet of coiling coils for pressure gauges, duct damper, including Control wiring to make M/V in close position while AHU is OFF with relays etc. Limit switch in door and inspection lamps to be fixed. Lockable off push button to be provided near AHU if machine is 3mtrs and above far from respective panel board to be included in the AHU cost. Fixing with bolts and nuts and finishing the slabs or any opening etc good as same. Notes : Fine filter efficiency 99.9 % down to 5 micron. Static Pressure for : Operation theater AHU's 100 mm Static Cathlab CT / MRI - 65 mm Static AHU's with fine filters - 55 mm Static all other AHU's - 50 mm Static; 4 TR, 1600 CFM, 6 row. Double Skin Ceiling Suspended AHU with mixing Box, 2 x 3 KW Heater
-do- 4 TR, 1600 CFM, 6 row. Double Skin Ceiling Suspended AHU with Mixing Box, 1 x 3 KW Heater
-do- 4 TR, 1600 CFM, 4 row. Double Skin Ceiling Suspended AHU with Mixing Box.
-do- 3 TR, 1350 CFM, 4 row. Double Skin Ceiling Suspended AHU with Mixing Box.
-do- 10 TR 4000 CFM, 4 row. Double Skin Floor mounted Horizontal AHU with mixing Box.
-do- 7 TR 2800 CFM, 4 row. Double Skin Floor mounted Horizontal AHU with mixing Box
-do- 10 TR 4000 CFM, 4 row. Double Skin Floor mounted Horizontal AHU with mixing Box and fine filter
-do- 9 TR 3600 CFM, 4 row. Double Skin Floor mounted Horizontal AHU with mixing Box and fine filter
-do- 8 TR 3200 CFM, 4 row. Double Skin Floor mounted Horizontal AHU with mixing Box and fine filter
-do- 6 TR, 2400 CFM, 4 row. Double Skin Ceiling Suspended AHU with Mixing Box, Fine filter
-do- 7 TR 3150 CFM, 6 row. Double Skin Floor mounted Horizontal AHU, Thermal break, 10 micron pre filters, fine filters, heater capacity 2 x 3KW, one Blower as stand by - for CT/MRI
-do- 7 TR, 3200 CFM, 8 Row - OT Double Skin Floor mounted Horizontal AHU with mixing box, 10 micron pre filters, 5 micron fine filters, heater capacity 2 x 3KW, Thermal break
TREATED FRESH AIR UNIT WITH HEAT RECOVERY WHEEL, VFD, SUPPLY & RETURN FANS
Supply at site, including, local transport, unload, store, handle, erect, balance and commission of the entire HRW as per specifications including all accessories as specified and as required. Summer Ambient conditions: DBT – 95 deg F, WBT- 82 Deg F Return Air condition: DBT- 75 Deg F , RH– 55% Supply Fan Static - 60 to 70 mm WG Return fan - 40 mm to 60 mm WG Efficiency 80- 85% ; TFA - 20 TR AHU, 6.9 sq.ft./ 8 Row coil with 3450 CFM Supply fan, 3100 CFM Return fan and heater coil of 2 x 3KW.
Fan Coil Units with valve station
-do- 1.25 TR Hideway FCU
-do- 1.5 TR Hideway FCU
-do- 2 TR Hideway FCU
-do- 4.5 TR High static FCU
Cassette type units with drain pump & fresh air provision Supply, installing, testing and commissioning of following cassette unit with drain pump & fresh air provision as per specification including all accessories as specified and as required - 1 TR One way cassette unit
-do - 1.5 TR Hiwall Unit
Supply, Installation testing and commissioning of split / Package air cooled Air-conditioners each complete with scroll compressor, air cooled condensor, GSS casing, filters, cooling coils, fan motors, insulated copper refrigerant piping as per drawing, control wiring, refrigerant controls and accessories, including MICRO-PROCESSOR CONTROL with indication lamps for the operation of the system with thermostat fixed in the respective rooms to adjust the temperature according to the equipments requirements with Micro- processor control panel for each machine. Tenderes to elaborate the features of Micro- processor panel. GI painted frame works for outdoor units & making good of civil work's. Refrigerant shall be R 410/R32. Price shall inclusive of all taxes & duties, installation, commissioning, Refrigerant piping as per Drawing. - 1.5 TR Hiwall Unit
CHILLED WATER PIPING & VALVES (Note: Wall openings for pipes & ducts, AHU Room and making good of opening to the complete satisfaction, pedestal for equipment are under the scope of HVAC contractor.)
Supply, receive, store, handle, install, test and commissioning of the following pre insulated chilled water MS class (B) pipes, including high tech supports complete with all fittings such as bends, tees, elbows, reducers flanges, special fittings, suspension hangers, supports etc. as required for installation as per site conditions and as per specifications. Undergorund piping shall have bitumen coating. Piping insulation shall be expanded polyurethane foam with 36 kg/cu m minimum density, 90% minimum closed cell content, minimum compressive strength of 40 psi and thermal conductivity of 0.14 Btu-in/hr/ft2/°F. The insulation shall completely fill the annular space between the service pipe and jacket and shall be bonded to both, the service pipe & jacket. All the fittings & bends shall be finished with the same finish as specified for preinsulated pipe, supplied by the same company. All supports pipes to be welded with V-cut grooves as per specifications. MS Class B, IS 3589, IS 1239 piping. RCC opening as good as same. Wall opening as good as same.: 200 mm dia.
-do - 150 mm dia.
-do - 125 mm dia.
-do - 100 mm dia.
-do - 80 mm dia.
-do - 65 mm dia.
-do - 50 mm dia.
-do - 40 mm dia.
-do - 32 mm dia.
-do - 25 mm dia.
-do - 20 mm dia.
Site fabricated pipe (MS class B) with adequate structural support and with PUF injection insulation & GI cladding for part plant room & AHU room area & valve insulation with openable boxing for inspection. - 200 mm dia.
-do - 100 mm dia.
DRAIN WATER PIPING: Supply and fixing in position of condensate drain water & AHU room drain pipe to the floor trap/nearest drain piping with 25 mm nitrile rubber insulation and with necessary fittings like traps, clamps, elbows, tees and reducers etc. Openings as good as same. - 32 mm dia. PVC
-do - 25 mm dia. PVC
BUTTERFLY VALVES Supply, installation, testing & commissioning of the following type Butterfly valves as per the specifications and as required. Butterfly valve shall cast iron body with black nitrile seat. All butterfly valves shall be provided with locking devices & PN 16 Rating. - 200 mm dia.
-do - 125 mm dia.
-do - 100 mm dia.
-do - 80 mm dia.
-do - 65 mm dia.
-do - 50 mm dia.
Supply, installation, testing & commissioning of the following type forged Ball Valve, PN-20 gunmetal /cast alloy, including all necessary accessories and connections. - 40 mm dia.
-do - 32 mm dia.
-do - 25 mm dia
-do - 20 mm dia
-do - 15 mm dia
Supplying, fixing, testing and commissioning of following size Drain valves with adequately supported as per specifications. - 40 mm
Supply, installation, testing & commissioning of the following Non Return Valves as per the specifications and as required. Non Return valves up to 65mm size shall be of gun metal with screwed female ends. Valves of 65mm and above shall be of CI with flanged ends. PN 16 pressure rating, EPDM seal. - Non- Return Valve of size:- 100 mm dia
BALANCING VALVE WITH PROVISION FOR FLOW MEASURMENT: Supply, installation, testing & commissioning of Balancing valve with built in measuring facility, C.I Body with EPDM seal, long pitch with protected out pipe insulation & PN 16 pressure rating for chilled water as specified. Balancing Valve with 90 Deg C maximum operating temperature; built-in locking device for Tamper-Proof positioning; flanged connections; Valves shall have connections with isolation device for portable differential pressure meter with integral seals, Flow accuracy shall be 5%+/-, necessary insulation as per specification. - 100 mm dia
SUCTION GUIDE with strainer: Supply, installation, testing & commissioning of the following suction guides as per the specifications and as required. - 100 mm dia.
Y STRAINER FOR AHU's: Supplying, fixing, testing and commissioning of following Y- Strainer in the chilled water piping duly insulated to the same specifications in the connected piping and adequately supported as per specifications. - 50 mm dia
-do - 40 mm dia
-do - 32 mm dia
-do - 25 mm dia
PRESSURE GAUGE: Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required
THERMOMETERS: Supply, installation, testing and commissioning of 4 inch Dial type thermometers with Stem with Copper-plated steel, aluminum, or brass for thermowell installation and of length to suit installation, Stainless Steel U-Siphon as per specification.
Supply, installation, testing & commissioning of differential pressure switch as per the specifications and as required.
Supply, installation, testing & commissioning of the following motorized cut off valves as per the specifications and as required. Cl Body, minimum PN-16 pressure rating, conforming to BS 5155, IS 13095, capable of accepting upto 10 V DC and upto 20mA electric signal and providing similar transduced feedback output to control system as required. - 100 mm dia.
500 L Pressurized Tank : Design, supply, installation, testing and commissioning of Pressurised chilled water expansion tank with insulation, Make up connection for closed loop system along with necessary pneumatic devices and accessories and MS 'C' section supports in order to keep chilled water under pressure. The tank shall be precharged steel tank with replacable heavy duty butyl rubber bladder. The tank shall have 50mm system connection and 20mm drain and charging valve connection to facilitate on-site charging of tank. The tank shall be fitted with lifting rings and floor mounting skirt for vertical installation. The tank shall be constructed according to section 8 of ASME boiler and pressure vessel code and stamped 125psi working pressure.The contractor shall submit calculation regarding the above data. Pumps shall be of N+1 configuration. including with control wiring
Supply, installation, testing & commissioning of a common air separator on the chilled water return line located at the pump suction and suitable for Secondary pump water flow; the separator shall be complete with high capacity air vent, flanges, service valve, non return valve, isolation butterfly valve for makeup water inlet. Capacity suitable for 648 USGPM and 200mm NB CHW Header line
AUTO AIR VENTS: Supply & install of airvents / purge valves at the highest points in chilled water piping complete each floor with pipes nipple welded to pipe, hex nipple, socket, U-pipe connection at outlet of air vent etc. as required.
Supply and fix flexible connections with control rods for pumps and chiller. Size: 100 mm dia.
TWO WAY TYPE PRESSURE INDEPENDENT BALANCING CUM MODULATING FLOW CONTROL VALVE: Supply, Installation, testing and commissioning of following size Pressure independent type 2 way modulating flow Control valves in a single Unit of Valves with PN16 Rating. DN 15 to DN 32 Brass Body Ext. Threaded, DN 40 & DN 50 Cast Iron Body Ext. Threaded, DN 65 to DN 100 Cast Iron body, Flanged Ends Connection Duly mounted with a BMS compatible Modulating actuator IP54 Type suitable for 24V AC for AHU/FCU as per specification - 50 mm dia.
-do- 40 mm dia.
-do- 32 mm dia.
-do- 25 mm dia.
CONDENSER WATER PIPING & VALVES (Note: Wall openings for pipes & ducts, AHU Room and making good of opening to the complete satisfaction, pedestal for equipment are under the scope of HVAC contractor.)
Supply, receive, store handle, install, test and commission the condenser water line with GI class (B) IS 3589 pipes complete with all fittings such as bends, tees, elbows, reducers, flanges, special fittings, suspension hangers, structural supports, etc. as reqd. for installation as per site conditions and as per specfiications. Opening as good as same. - 200 mm dia.
-do-125 mm dia.
-do-100 mm dia.
Supply, installation, testing & commissioning of the following type Butterfly valves as per the specifications and as required. Butterfly valve shall cast iron body with black nitrile seat. All butterfly valves shall be provided with locking devices & PN 16 Rating. - 125 mm
Supply, installation, testing & commissioning of the following Non Return Valves as per the specifications and as required. Non Return valves up to 65mm size shall be of gun metal with screwed female ends. Valves of 65mm and above shall be of CI with flanged ends. PN 16 pressure rating, EPDM seal. - 125 mm dia
Supply, installation, testing & commissioning of the following suction guides as per the specifications and as required. - 125 mm dia
Supply and fix flexible connections with control rods for pumps, cooling tower & condenser. - 125 mm NB
Supply, installation, testing & commissioning of Balancing Valve, with built in measuring facility with C.I Body, 90 Deg C maximum operating temperature; built-in locking device for Tamper-Proof positioning; flanged connections;Valves shall have connections with isolation device for portable differential pressure meter with integral seals, Flow accuracy shall be 5%+/- : 125 mm NB
Supply, installation, testing and commissioning of 4" Dial type thermometers with Stem with Copper-plated steel, aluminum, or brass for thermowell installation and of length to suit installation, Stainless Steel U-Siphon as per specification
Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required
Supply, installation, testing & commissioning of differential pressure switch as per the specifications and as required.
Supply, installation, testing & commissioning of the following motorized cut off valves as per the specifications and as required. Cl Body, Nylon coated DI disc, EPDM seal, minimum PN-16 pressure rating, conforming to BS 5155, IS 13095, capable of accepting upto 10V DC and upto 20mA electric signal and providing similar transduced feedback output to control system as required. - 125 mm dia
DUCTING, GRILLS, DIFFUSER & INSULATION (Note: Wall openings for pipes & ducts, AHU Room and making good of opening to the complete satisfaction, pedestal for equipment are under the scope of HVAC contractor.)
Supply, fabricate, handle, erect, balancing and commissioning of below thickness factory fabricated GSS ducting as per drawing, complete with all fittings such as tee bends, special off-chutes, turning vanes, splitter dampers, ins.doors, transformation pieces, slip on flanges, rubber gaskets, elbows, hangers, supports etc. etc. as reqd. as per IS 655 including suspension and supporting arrangement for plenums, ducts, complete as required. and as per specification. - Thickness 0.63 mm GSS sheet
-do - Thickness 0.80 mm GSS sheet
-do - Thickness 1.00 mm GSS sheet
Supply, fabricate, handle, erect, balancing and commissioning of below thickness factory fabricated Aluminium ducting as per drawing, complete with all fittings such as tee bends, special off-chutes, turning vanes, splitter dampers, ins.doors, transformation pieces, slip on flanges, rubber gaskets, elbows, hangers, supports etc. etc. as reqd. as per IS 655 including suspension and supporting arrangement for plenums, ducts, complete as required. and as per specification. - Thickness 0.80 mm Al. Sheet ducting
-do- Thickness 1.00 mm Al. Sheet ducting
-do- Thickness 1.25 mm Al. Sheet ducting
GRILLES & DIFFUSERS Supplying and Fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.
Supplying and Fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.
Supply and fixing of Square Supply air diffusers of powder coated Aluminium with opposed blade dampers with removable core as per drawings for the following neck sizes. The diffusers shall have extended flanges to match the grid tile of 600x600 : SD: 450×450
Supply and fixing of Square Return air diffusers of powder coated Aluminium with removable core as per drawings for the following neck sizes. The diffusers shall have extended flanges to match the grid tile of 600x600 : RD: 450×450
Supply installing, testing and commissioning of perforated aluminium grille for return with VCD and 10 Micron Filter in OT
Supply, Fabrication, installation and testing of following size insulated flexible duct, complete with connecting rings, duct supports etc. as per standards and specification. : 350 mm dia
-do -300 mm dia
-do -250 mm dia
Supply installing, testing and commissioning of following Insulated Plenum Box made of 22g G.I & Spigot & Butterfly Dampers with necessary threaded rods for supporting for the following sizes : 600 X 600 X 450 H
-do -450 X 450 X 450 H
-do -350 X 350 X 450 H
-do -300 X 300 X 300 H
Supply installing, testing and commissioning of Factory made fresh air dampers with louvers and control lever, filter etc as required. (As per drawing)
Supply installing, testing and commissioning of Factory made fresh air dampers having 20 micron filter with louvers and control lever. (For OT as per drawing)
Supply, fixing, balance and commissioning of louvre type smooth supply air duct dampers made of extruded aluminium linkage, lever, brass bushings complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges, fixing arrangement etc, as per specifications. Al Volume control duct damper
Supply and fix 1 1/2 hour fire rated fire dampers air ducts (main line) with fusible link & microswitch to shut of corresponding AHU (including control cable.)
DUCT INSULATION & LINING Thermal insulation: Supply & fixing of 8 mm thick Class O nitrile rubber insulation with antimicrobial property with adhesive as per the recommendation of the manufacturer with density 45-55kg/m3
Acoustic insulation: Supply & fixing of 10 mm thick Class 1 acoustic nitrile rubber insulation with antimicrobial property with adhesive as per the recommendation of the manufacturer with density 140-180kg/m3
Non AC area duct insulation: Supply & fixing of 19 mm thick Class O nitrile rubber insulation with adhesive as per the recommendation of the manufacturer with density 45-55kg/m3
VENTILATION SYSTEM
Axial Fans - for Toilet, Plant room exhaust & Fresh Air: Supply, installation, testing and commissioning Direct driven axial flow fans suitable for mounting on wall or duct in standard galvanized/ powder coated steel construction with required rating, static, single motor and flexible connection to connect with ducting / plenum, louvers with birdscreen : 80 cfm Exhaust blower
-do -100 cfm Exhaust blower
-do -150 cfm Exhaust blower
-do -200 cfm Exhaust blower
-do -250 cfm Exhaust blower
-do -300 cfm Exhaust blower
-do -350 cfm Exhaust blower
-do -400 cfm Exhaust blower
-do -450 cfm Exhaust blower
-do -550 cfm Exhaust blower
-do -650 cfm Exhaust blower
-do -700 cfm Exhaust blower
-do -700 cfm Fresh Air blower
-do -800 cfm Exhaust blower
-do -800 cfm Fresh Air blower
-do -900 cfm Fresh Air blower
-do -1000 cfm Exhaust blower
-do -1100 cfm Exhaust blower
-do -1200 cfm Exhaust blower
-do -1250 cfm Exhaust blower
-do -1300 cfm Exhaust blower
-do -1400 cfm Exhaust blower
Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006 : Thickness 0.63mm Sheet
-do -Thickness 0.80mm Sheet
Supply, Fabrication, installation and testing of the flexible ducting, complete with connecting rings, duct supports, Plenum etc as per standards and specification. : Size: 100mm dia.
GRILLES & DIFFUSERS Supply and fixing the following aluminium grilles and diffusers as per specifications. Machine made, powder coated, supply and return air grilles and diffusers. Design to be approved. Supply / Return air grille/diffuser with vcd
ADDITIONAL WORKS
Acoustic Lining of AHU Rooms/boxing without Mixing Box / Boxing Insulation for Ceiling suspended AHU. Supply & fixing of 15 mm thick acoustic nitrile rubber insulation with adhesive as per the recommendation of the manufacture with density 140-180kg/m3
UNDER DECK INSULATION - Supply & fixing of 19 mm thick class O nitrile rubber insulation with adhesive as per the recommendation of the manufacture with density 45 - 55kg/m3
ELECTRICAL WORK
AHU PANEL / SM DB L1 Fabrication, supply, erection, testing and commissioning of cubicle type as per IEC 61439 and internal arc test as per IEC 61641, dust and vermin proof, floor/wall mounted, front operated MV panel board made out of 16 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as required. All opening parts of the panel shall be sealable. (complete specification as detailed in Part C - Schedule of Quantities)
AHU PANEL / SM DB L2 Fabrication, supply, erection, testing and commissioning of cubicle type as per IEC 61439 and internal arc test as per IEC 61641, dust and vermin proof, floor/wall mounted, front operated MV panel board made out of 16 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as required. All opening parts of the panel shall be sealable. (complete specification as detailed in Part C - Schedule of Quantities)
AHU PANEL / SM DB L3 Fabrication, supply, erection, testing and commissioning of cubicle type as per IEC 61439 and internal arc test as per IEC 61641, dust and vermin proof, floor/wall mounted, front operated MV panel board made out of 16 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as required. All opening parts of the panel shall be sealable. (complete specification as detailed in Part C - Schedule of Quantities)
AHU PANEL / SM DB L4 Fabrication, supply, erection, testing and commissioning of cubicle type as per IEC 61439 and internal arc test as per IEC 61641, dust and vermin proof, floor/wall mounted, front operated MV panel board made out of 16 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as required. All opening parts of the panel shall be sealable. (complete specification as detailed in Part C - Schedule of Quantities)
AHU PANEL / SM DB L5 Fabrication, supply, erection, testing and commissioning of cubicle type as per IEC 61439 and internal arc test as per IEC 61641, dust and vermin proof, floor/wall mounted, front operated MV panel board made out of 16 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as required. All opening parts of the panel shall be sealable. (complete specification as detailed in Part C - Schedule of Quantities)
AHU PANEL / SM DB L6 Fabrication, supply, erection, testing and commissioning of cubicle type as per IEC 61439 and internal arc test as per IEC 61641, dust and vermin proof, floor/wall mounted, front operated MV panel board made out of 16 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as required. All opening parts of the panel shall be sealable. (complete specification as detailed in Part C - Schedule of Quantities)
AHU PANEL / SM DB L7 Fabrication, supply, erection, testing and commissioning of cubicle type as per IEC 61439 and internal arc test as per IEC 61641, dust and vermin proof, floor/wall mounted, front operated MV panel board made out of 16 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as required. All opening parts of the panel shall be sealable. (complete specification as detailed in Part C - Schedule of Quantities)
LT CABLE SUPPLY Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. : 4CX35sq.mm Al Cable
-do - 4CX25sq.mm Al Cable
-do - 4CX6sq.mm Al Cable
-do - 4CX4sq.mm Al Cable
-do - 3CX6sq.mm Al Cable
-do - 3CX4sq.mm Al Cable
-do - 3CX2.5sq.mm Al Cable
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on cable tray as required.: Upto 35 sq. mm (clamped with 1mm thick saddle)
Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. - 2C x 1.5 sq. mm
3C x 1.5 sq. mm
6C x 1.5 sq. mm
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. - 4CX35sq.mm Al Cable
4CX25sq.mm Al Cable
4CX16sq.mm Al Cable
4CX6sq.mm Al Cable
4CX4sq.mm Al Cable
3CX6sq.mm Al Cable
3CX4sq.mm Al Cable
Supply and laying the following sizes of earthing bare copper/strips on cable tray or wall surface, including necessary clamps (each clamp not exceeding 60 cm) and bolts etc as required for complete installation as instructed by engineer in charge/consultant. - Copper wire No.10 SWG
Copper wire No.8 SWG
BUILDING MANAGEMENT SYSTEM
System controller SITC of Central core Computer - PC (Intel i7 Processor) , 8 GB RAM, 2 GB Graphics card, DVD Writer, 22" LED monitor, 1 TB HDD, Microsoft mouse, Keyboards, 2 serial, 1 parallel port/KB, Windows 8 operating system, antivirus software
SITC of A4 Colour Laser printer
Supply, Installation, Testing and Commissioning of Building Management System Graphic User Interface software with 3 user client license, user groups, user profiles and scopes, alarm handling, scheduling, trending, reporting engine, database system, system activity log, historical data management, real time zoom enabled vector graphics, system backup and restore, HTML based documentation and help, SMS/EMail facility complete in all respects as per tender specification. Graphical Software complete to cater to hardware points as specified in the Data Point Summary as well as Third Party Software Integrated Systems.
SITC of Interface for integrating Third Party Systems. (All Systems to provide data on MODBUS RTU with values shown on MODSCAN or BacNET shown on BacNET explorer). Chiller System - 3 Chiller (50 points/chiller)
SITC of Interface for integrating Third Party Systems. (All Systems to provide data on MODBUS RTU with values shown on MODSCAN or BacNET shown on BacNET explorer). Secondary Pumps System (10 Points/Pump)
SITC of Interface for integrating Third Party Systems. (All Systems to provide data on MODBUS RTU with values shown on MODSCAN or BacNET shown on BacNET explorer). Variable Frequency Drives for AHU's (10 Points per VFD
Controls for Chiller System
SITC of Networkable DDC Controllers as per Data Point Summary (1- 5 ) with enclosure with all necessary wiring and accessories
SITC of Immersion Type Temperature Sensor
SITC of Outside Air Temperature & RH Sensor
SITC of Level Switch for expansion tank ( 2 point) (depth of tank - 1 mtr.)
SITC of Differential Pressure Switch
SITC of Level Switch for cooling tower
Control for Air Handling Units
Supply, Installation, testing & commsssioning of the DDC Controllers with enclosure with all necessary wiring and accessories, consider 2 AHU / DDC
Supply, Installation, testing & commsssioning of the DDC Controllers with enclosure with all necessary wiring and accessories, consider 1 AHU / DDC
Supply, Installation, testing & commsssioning of the DDC Controllers with enclosure with all necessary wiring and accessories, consider 3 AHU / DDC
SITC of Differential Pressure Switch across filter for Air Handling Units - 6 Nos.
SITC of Return air Temperature Sensor for Air Handling Units - 6 Nos.
SITC of Differential Pressure Switch across filter - pre filter and fine filter for Air Handling Units with Fine filter- 6 Nos
SITC of Return air Temperature Sensor for Air Handling Units with Fine filter- 6 Nos
SITC of Differential Pressure Switch across filter for Air Handling Units with heater - 2 Nos.
SITC of Return air Temperature Sensor for Air Handling Units with heater - 2 Nos.
SITC of RH Sensor Room type for Air Handling Units with heater - 2 Nos.
SITC of Differential Pressure Switch across filter for Air Handling Units with fine filter, heater - 1 Nos.
SITC of Return air Temperature Sensor for Air Handling Units with fine filter, heater - 1 Nos.
SITC of RH Sensor Room type for Air Handling Units with fine filter, heater - 1 Nos.
SITC of Differential Pressure Switch across filter -Pre filter,fine filter and Hepa filter for Air Handling Units - 9 Nos. - OT
SITC of Return air Temperature Sensor for Air Handling Units - 9 Nos. - OT
SITC of RH Sensor Room type for Air Handling Units - 9 Nos. - OT
SITC of Air Diffrential Pressure Sensor for Air Handling Units - 9 Nos. - OT
SITC of Differential Pressure Switch across filter for AHU with Heat Recovery Wheel - 1 Nos
SITC of Return air Temperature Sensor for AHU with Heat Recovery Wheel - 1 Nos
SITC of RH Sensor Room type for AHU with Heat Recovery Wheel - 1 Nos
Cabling Works for BMS
SITC of Signal Cabling - 2 Core 1.0 sq.mm. shielded FRLS armoured cable
SITC of Signal Cabling - 4 Core 1.0 sq.mm. shielded FRLS armoured cable
SITC of Signal Cabling - 8 Core 1.0 sq.mm. shielded FRLS armoured cable
SITC of Communication Cabling - 2 Core 1.5 sq.mm. shielded FRLS armoured cable or CAT6 armoured cable
SITC of Power Cable - 3 C X 2.5 Sq.mm. -ATC Armoured Cable
SITC of Cable Trays (150mm X 50mm) - approx
SITC of 5 Amps Power Sockets
SITC of 3 KVA UPS - Min 1 Hr minutes back up for the system)
MEDICAL GAS PIPELINE SYSTEM (MGPS)
SITC of Oxygen Manifold - 2 banks x 10 cylinders
SITC of Fully Automatic Oxygen Control Panel with minimum flow rate of 1500 LPM
SITC of Emergency Oxygen Manifold - 2 banks x 5cylinders
SITC of Oxygen Flowmeters with humidifier bottle
SITC of Nitrous Oxide Manifold - 2 banks x 1 cylinders
SITC of Fully automatic Gas Control Panel for Nitrous Oxide with a minimum flow rate of 500 LPM
SITC of Emergency Nitrous Oxide Manifold - 1 bank x 1 cylinders
SITC of Carbon Dioxide Manifold - 2 banks x 1 cylinders
SITC of Fully automatic Gas Control Panel for Carbon Di Oxide with minimum flow rate of 300 LPM
SITC of Emergency Carbon Dioxide Manifold - 1 bank x 1cylinders
SITC of Compressed air plant system having minimum free air delivery of 1500 LPM with complete accessories as mentioned in technical specifications.
SITC of vacuum plant system having minimum free air aspirated of 2500 LPM at 450 mmHg with complete accessories as mentioned in technical specifications.
Ward Vacuum Units
Theatre Vacuum Units
SITC of Electrical Panel for Air Compressor & Vacuum Pump
SITC of ICU Terminal Units - Imported - O2
SITC of ICU Terminal Units - Imported - Air
SITC of ICU Terminal Units - Imported - VAC
SITC of Ward Terminal Units - Indigenous - O2
SITC of Ward Terminal Units - Indigenous - N2O
SITC of Ward Terminal Units - Indigenous - Air
SITC of Ward Terminal Units - Indigenous - Air 7 bar
SITC of Ward Terminal Units - Indigenous - Vac
SITC of Matching Probe - O2
SITC of Matching Probe - N2O
SITC of Matching Probe - Air
SITC of Matching Probe - Air 7 bar
SITC of Matching Probe - VAC
SITC of Master Plant Alarm Panel (post source), BMS compatible,
SITC of Area Valve Service Units with Alarm Systems - 6 Services
SITC of Area Valve Service Units with Alarm Systems - 4 Services
SITC of Area Valve Service Units with Alarm Systems - 2 Services
SITC of Copper pipe - per mtr. - 12mm
SITC of Copper pipe - per mtr. - 15mm
SITC of Copper pipe - per mtr. - 22mm
SITC of Copper pipe - per mtr. - 28mm
SITC of Copper pipe - per mtr. - 35mm
SITC of Copper pipe - per mtr. - 42mm
SITC of Copper pipe - per mtr. - 54mm
SITC of Copper pipe - per mtr. - 76mm
SITC of Copper pipe - per mtr. - 108mm
SITC of Ball Valves - 15mm
SITC of Ball Valves - 22mm
SITC of Ball Valves - 28mm
SITC of Ball Valves - 35mm
SITC of Ball Valves - 42mm
SITC of Ball Valves - 54mm
SITC of Ball Valves - 76mm
SITC of Bed Head Units - 1000 mm for Wards
SITC of Bed Head Units - 1500 mm for ICU Category.
SITC of Bed Head Panel - Running Meter
SITC of Rigid Pendent
ELEVATOR SYSTEM
Supply installation, testing and commissionin of following capacity, gearless with machine room type passenger lift of 1.5 M/s Speed with all accessories, control equipment for a total travel of 30 Meters (Approx.) with 7 landing/stops (Ground to 6th floor) and 7 opening, fully motorized doors as per the detailed specification mentioned. The lift shall be with emergency alam device, emergency light with UPS backup, overload protection, advance door opening, Re-leveling operation facility, automated fan and light controls, LED Stop disply on top of door side, Rescue operation to the next landing while door operation failure and lift stopped out of level zone etc. All landing shall be with entrance frame, landing doors of stain less steel in 304 grande, hall indicators, hall call box with face plate and landing sill etc with all accessiories required for complate installation as required as per the standard and requirements. The scope of also include necessary approvals from concerened authority. Necessary shaft lighting and power sockets shall also be included in the scope of work including supply off necceasry materials for shaft lighting and power sockets like bulk head light of approve make, swich socket, conduit wire etc. Passenger cum Bed Lift 1 - 26 Pax, 1760 kgs (complete specification as detailed in Part C - Schedule of Quantities)
-do- Goods cum Bed Lift 1 - 2000 kgs
CHERIAN VARKEY CONSTRUCTION CO PVT LTD
Bidder Name
CHERIAN VARKEY CONSTRUCTION CO PVT LTD
Silpa Projects and Infrastructure India Pvt Ltd
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.05 MB
Download all tender documents and submit your bid