SPECIAL REPAIR TO BUILDING NO T-23, T-24 AND T-26 UNDER GE SAMBA AT SAMBA MIL STN

Amount

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified.

Dismantling timber scantlings 40 Sqcm and over in section, in any position and unframed/framed work complete all as specified complete all as specified and directed.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premisesr complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

S&F in repair 7 to 9mm thick Gypsum tile colour touch sizing 595 x 595mm with LA Gypsum "T" bar metal profile manufactured from high quality galvanished steel, main runner 24 x 33mm, thickness 0.3mm, cross runner 24 x 25mm, thickness 0.3mm, wall angle 18 x 18mm along with other system components accessories such as butterfly clip 0.5mm thick hold down clip 0.4mm thick and duly suspended with GI bar hangers by royal plugs etc and necessary drilling etc as per manufactures instructions complete all as specified and directed.

Demolition of Concrete (Reinforced) of any description and in any position not otherwise specifically provided for , complete all as specified and directed.

Taking down chowkhats or frames of any description not exc 1.50 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware , complete all as specified and directed.

Taking down chowkhats or frames of any description exc. 1.50 Sqm and n.exc 4.00 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware complete all as specified and directed.

Taking down Shutters of any description not exc 1 sqm each including builders hardware complete all as specified and directed.

Taking down Shutters of any description exc 1 sqm and n exc 2 sqm each including builders hardware complete all as specified and directed.

Taking down door Shutters of any description exc 1 sqm and n exc 2 sqm each and refixing the same after easing and adjusting/resizing including builders hardware complete all as specified and directed.

M&L for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws incl dismantling of existing sheets of any type complete all as speecified and directed. [Note : The colour of sheet shall be as approved by GE]

M&L for Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick having tensile strength of 550 Mpa as in ridge, fixed with self tapping screws incl dismantling of existing sheets of any type complete all as speecified and directed. [Note : The colour of sheet shall be as approved by GE]

M&L for pressed steel frames 125mmx60mm for door, made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate and back filling for chowkats in PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) tarring ends incl 02 coats of synthetic enamel paint over a coat of red oxide primer on exposed surface complete all as specified and directed.

M&L for pressed steel frames 105mmx60mm for door, made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate and back filling for chowkats in PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) tarring ends incl 02 coats of synthetic enamel paint over a coat of red oxide primer on exposed surface complete all as specified and directed.

M&L for 35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12mm veneered particle board with commercial veneering on both faceS ,The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated, fitted to chowkhats incl 02 coats of synthetic enamel paint over a coat of pink primer after preparation of surfaces complete all as specified and directed.

M&L for 35mm thick glazed and skeleton shutters (Factory made) of 2nd class hard wood and prepared to receive glass or gauge etc with rounded, chamfered or mitred sash bars edges of framing plain chamfered or rounded fitted with cut and mitred beads and fitted to chowkats for securing glass/gauge, size of stiles rails and other parts as per clause 8.20 (a) of SSR Part-I 2009 (Larger size to be provided) incl 02 coats of synthetic enamel paint over a coat of pink primer after preparation of surfaces complete all as specified and directed.

M&L for factory made PVC internal door frame of the size 100mm x 45mm with a wall thickness of 5mm, made out of extruded 5mm thick prelam PVC sheet of density 600kgs/cbm manufacturured by an ICO-9000 certified company mitre, mitre cut at two corners and joined with 4 nos of 150mm long brackets of 1500 x 1500 M.S tube of 19 guage through out the frame. The door frame shall be fixed to the wall using 65/100mm long M.S screws to be provided for each vertical member & minimum 2 nos for horizental members etc. complete as per manufactures specification and direction of Engr-in-charge.

M&L for factory made solid PVC wood grain pre-painted PVC sheet moulded door shutters, 30mm thick (stiles), with PVC solid board core not less than 18mm thick and 2, 4, or 6 raised panel design with 5mm thick moulded prelam PVC sheet on the front face & 5mm thick prelam PVC sheet on back face, supplied and fixed in frame at site as per specification and shown in SSR Part-II Section-8 complete all as specified and directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty or fixed with beads/ glazing pins not .exc 0.5sqm in each pane complete all as specified and directed.

All as per Srl item No. 21 above but including hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks, orstainless steel wire staples complete all as specified and directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty or fixed with beads/ glazing pins not .exc 0.5sqm in each pane complete all as specified and directed.

M&L for 3 mm thick Figured glass, pin head type & glazing with oil putty in squares n exc 0.5 sq.m in each panecomplete all as specified and directed.

M&L for stainless steel Butt hinges of size 100 mm fixed with steel screws of appropriate size complete all as specified and directed.

M&L for 250mm aluminium alloy, anodised sliding door bolt with hasp & staple (bolt type) and fixing clip of sheets cast or extruded section and fixing sliding bolt of extruded section etc complete all as specified and directed.

M&L for aluminium anodized barrel tower bolts 150 mm of extruded section and fixed. complete all as specified and directed.

M&L for Aluminium anodised handle, extruded section of size 150mm etc complete all as specified and directed.

M&L for 150 mm MS tail helical door spring including roller and roller plate, complete all as specified and directed.

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

Dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc and removal of rubbish out off the premises complete all as specified and directed.

M&L for Brick work with Fly Ash Brick (Non-Modular) Class 7.5, straight or curved on plan exceeding 6m mean radius built in CM (1:6) complete all as specified and directed.

M&L for Brick work (except bricks) for brick work (with serviceable bricks retrieved from dismantling straight or curved on plan exceeding 6m mean radius built in CM (1:6) complete all as specified and directed. [Note: Serviceable Brick retrived from dismentling shalll be reused in this work]

M&L for 20-25mm thick Kota stone slab in floor (Pre-mirror polished), set and jointed in neat cement slurry and pointed in coloured epoxy grout over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for kota stone floor 18-20 mm thick, as in skirting, dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick backing coat/ rendering in CM 1:3, surfaces finished even and rough to receive kota stone complete all as specified and directed.

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections ) including distance pieces, cleats etc of Fe-410-W (Gde-E-250) quality-A, complete all as specified and directed.

S&F 2mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed.

M&L for Cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregates) such as in benching, coping, Bed blocks , broken chajjas and the like, rounded or chamfered on edges including necessary formwork including demolition of existing concrete of any description and removal of debris out off the premises etc complete all as specified and directed.

S&F in repair for single towel rail brass chromium plated 600mm long fixed with chromium plated screw and PVC cleat complete all as specified and directed. Make : Cat part No AQN-7711 of Jaquar or equivalent model in Hindware/Marc.

M&L for Vitreous china wash hand basin, white, flat back, size 550x400mm (Make : Jaquar Cat part No CNS-WHT-801 or equivalent model in Hindware/Parryware/Somany) including 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated (Make : Jaquar Cat part No FLR-5011N or equivalent model in Hindware/Marc.) brackets, CP waste coupling, 32mm bore PVC waste pipe of min 600mm long & 15 mm bore PVC connections, including cutting for and pinning in end of brackets or erecting stand fixed in repairs complete all as specified and directed.

Taking up or down 15mm bore pipe and connections including cleaning for refixing including all new fittings for 15mm bore complete all as specified & as directed.

Taking up or down 20mm bore pipe and connections including cleaning for refixing including all new fittings for 20mm bore complete all as specified & as directed.

M&L for GI water tubing surface/concealed, 15mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Refixing of old steel tubing 15mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) fixed to wall , floor etc complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring, etc, and making good, cutting not exc 10 cm girth complete all as specified & directed.

M&L for GI water tubing surface/concealed, 20mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Refixing of old steel tubing 20 mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) fixed to wall , floor etc complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

S&F 15 mm bore Stop valves/Angle valve cast copper alloy, chromium plated (ISI marked) , screwed down,high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair complete all as specified and directed.

S&F 20 mm bore Stop valves/Angle valve cast copper alloy, chromium plated (ISI marked) , screwed down,high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair complete all as specified and directed.

S&F in repair for 15mm bore bib taps fancy type with wall flange, chromium plated cast copper alloy long body with capstan heads, screwed for iron pipe or brass ferrule complete all as specified and directed.

M&L for rendering 15mm thick on brick work or concrete surface in CM (1:6) on wall surfaces finished even and smooth using extra cement complete all as specified & directed.

M&L for Rendering 15mm thick in two layers [base layer 10mm IN CM 1:6 & finishing layer 5mm thick in cement mortar (1:4)] using liquid water proofing compound in IInd layer only on brick work or concrete surfaces of wall, surfaces finished even and smooth using extra cement complete all as specified & directed. (Note : WPC shall be measured and paid separately)

M&L for Box type Steel windows and ventilators comprised of tubular frame and shutters made out of 1.25mm thick M S sheet tube factory made with double side hung wire gauged shutter & glass/glazed shutter (wire cloth and glass panes only shall be measured and paid separately) with steel handle and steel peg stay dovetailed or welded incl 2 Nos. tower bolts 150mm long for each leaf and 10mm square bar grills at spacing as shown on drg, welded to F I frame work, including other fittings; hinges, handles, tarred hold fasts fixed in PCC blocks all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete complete all as specified and directed.

M&L for Factory made rubberised coloured chequered tiles of size 250x250x25mm thick (using vibro compaction method) with 3mm to 5mm thick topping in white cement and non fadeble glossy pigment set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:4) surface finished even and rough to receive topping over and including 75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in sub-base, surface finished even and rough including demolition of existing tiles path of any description and removal of debris out off the premises etc complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-1 using 20mm graded crushed stone aggregate as in plinth protection laid in panels and joints filled with mix of bitumen and sand (1:3) by weight, finished the surface even and smooth using extra cement including demolition of damaged plinth protection and removal of debris out off the premises etc complete all as specified and directed.

M&L for 25 mm thick floor in PCC 1:2:4 type B-0(12.5mm graded aggregate) as in sub base for flooring , complete all as specified and directed.

M&L for Non-skid ceramic coloured rectified edges tiles 8mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc, set & jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:4) complete all as specified and directed.

M&L for Glazed ceramic (coloured) tiles 7mm thick, of size 450mmx300mm on vertical surfaces such as dado etc, set and jointed in neat cement slurry and pointed in coloured epoxy grout to match tiles over and including 10mm thick backing coat in cement mortar (1:4), surface finished even and rough to receive tiles, including dismantling existing tiles of any type and pattern complete all as specified and directed.

S&F for Vitreous china White Squatting Orissa Pattern pan (Make : Somany Cat part No 121115 or equivalent model in Hindware/Parryware) of size 580x440mm, including cast iron ‘P’ or ‘S’ trap, front or back inlet and integral foot rests and making connection to trap and to flushing pipe, anti syphonic pipe,including provision of PCC 1:5:10 type E-2 bedding including demolition complete all as specified and directed. (Note : Demolition and refilling of concrete in sunken portion is included in the Contractor quoted rate.)

S&F in repair Brass Chromium Plated shower rose with arms fancy type with swivel joints 125 mm face dia of appoved make and cat part for 15mm bore iron pipes complete all as specified and directed. Make : Prayag Cat part No BS-73 or equivalent model in Hindware/Marc.

S&F in repair for PVC flushing cistern dual flush type 10 Ltr capacity, valve-less syphonic action type, low level, complete with inlet, ball valve, handle, including brackets/pins, PVC flush pipe 32mm bore complete all as specified and directed.

S&F in repair for PVC connection 15mm size with PTMT nuts of length 450mm long of appoved make complete all as specified and directed.

S&F in repair for Rotational moulded polyethylene water storage tanks three layer of capacity 500 litre, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm ball valve high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and dismantling of existing PVC tank of any capacity, complete all as specified & directed.

M&L for PVC (SWR) rain water pipes of 110 mm bore dia in any length, with rubber ring joints,laid in trenches or as in floor including taking down existing SWR pipes etc incl earthwork if required complete all as specified & directed.

M&L for PVC (SWR) rain water pipes of 75 mm bore dia in any length, with rubber ring joints,laid in trenches or as in floor including taking down existing SWR pipes etc incl earthwork if required complete all as specified & directed.

S&F in repair for PVC (SWR) floor trap 75 mm dia outlet, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 110 mm bore bends PVC (SWR) (any radius) fixed with cement solvent etc complete all as specified and directed.

S&F 75 mm bore bends PVC (SWR) (any radius) fixed with cement solvent etc complete all as specified and directed.

M&L for preparation of old painted wood surfaces of any description over 10 cm in width or girth & applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description over 10 cm in width or girth & applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint over a coat of primer as per manufacturer instructions complete all as specified and directed.

M&L for preparation of Old plastered surfaces of wall & applying two coats of cement base paint over a coat of primer as per manufacturer instructions complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of distemper oil emulsion (OBD) over a coat of primer as per manufacturer instructions (from same manufacturer of OBD) over a layer of wall care putty 3mm thick complete all as specified and directed.

Complete removal of existing treatment & preparation of plastered surface of walls applying two coats of distemper oil emulsion (OBD) over and including a coat of primer as per manufacturer instructions (from same manufacturer of OBD) over and including a layer of wall care putty not less than 3mm thick complete all as specified and directed.

Taking down carefully unserviciable/ damaged copper/aluminium surface (batten/coduit or casing caping) point wiring any length for light/fan/socket or power including unscrewing from board (fitting and fixture such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sockets, Bracket /sketch fitting etc ) and removing material from site and making good to the disturbed surface to match with existing finish complete all as specified and directed.

M&L for Modular Point wiring using FRLS PVC insulated unsheathed /multi stranded copper conductor cable 1.5 sqmm including 1.5 Sqmm FRLS PVC insulated unsheathed copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bends, junctions box and approved make sunken modular metal flush gang box and suitable support frame and cover plate (inner/outer) of required modules for mounting modular switches/ sockets etc, connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc (conduit shall be fixed on surface of ceiling with necessary saddles where concealing of conduit is not feasible), for light/fan/bell point complete all as specified and directed. Make of cable : Finolex, Anchor, Polycab (Note : Modular switch/bell push/fan regulator etc shall be measured and paid separately under respective items.)

All as per Srl item No. 79 above but for 5 pin 5 Amp socket outlet point on independent gang box and suitable support frame and cover plate (inner/outer) controlled by one switch 5Amp one way, etc complete all as specified and directed.

All as per Srl item No. 79 above but for 5 Pin 5 Amp socket outlet point on same board controlled by one switch 5 Amps one way on same gang box support frame and cover plate etc complete all as specified and directed.

All as per Srl item No. 79 above but for one 15Amp socket outlet point concealed using 2.5Sqmm FRLS PVC insulated multi-strand copper conductor wire including 2.5Sqmm FRLS PVC insulated unsheathed copper conductor earth wire and making good to disturbed surfaces of wall floor to match existing finishes complete all as specified and directed.

S & F modular switch piano type flush button one way 06/10 Amp one module complete all as specified and directed. Make : Legrand Cat Part No 673000/Crabtree Cat Part No ACMSXXW101/Anchor Roma Cat Part No 66111.

S & F modular switch piano type flush button 16 Amp one module, complete all as specified and directed. Make : Legrand Cat Part No 673009/Crabtree Cat Part No ACMSXXW102/Anchor Roma Cat Part No 66104.

S & F modular socket outlet 2 module 5/6 pin 6/10 Amp,complete all as specified and directed. Make : Legrand Cat Part No 673044/Crabtree Cat Part No ACMKUXW133/Anchor Roma Cat Part No 66403.

S & F modular socket outlet 16 Amp 5/6 pin two module complete all as specified and directed. Make : Legrand Cat Part No 673455/Crabtree Cat Part No ACMKCXW163/Anchor Roma Cat Part No 66404.

S&F Ceiling rose polycarbonate isolated body surface Bakelite, not less than 65 x 50 mm, three terminals, AC 230 volts etc, complete all as specified and directed. Make : Havells Cat Part No Reo/Cona Cat Part No 9246/GM Cat Part No 8224

Taking down ceiling fan of any sweep & size and refix in same position after overhauling including minor repairs by replacement of capacitor, safety pin, cap, nuts & bolts etc and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose to fan, including testing to ensure efficient functioning including application of one coat of synthetic enamel paint by spray painting & rewriting number complete all as specified and directed.

S & F Fan regulator modular step type suitable for 1200/1400mm sweep ceiling fan hum free, 120W- 2 module including necessary connections complete all as specified and directed. Make : Legrand Cat Part No 673028/Crabtree Cat Part No ACARFHW005/Anchor Roma Cat Part No 66502.

S&F Lamp holder insulated body with back plate suitable for batten fitting including 10W LED lamp of approved make and cat part and PVC Round/Square block etc complete all as specifeid and directed.

S &F the Bulk head light fitting LED type 10 watt complete with 10 watt LED and having IP-63 protection and fixing on wall/ceiling complete with all accessories and including connecting up with ceiling rose with & including PVC insulated and overall sheathed flexible copper conductor cable and including 3 core 0.50 Sqmm complete all as specified and directed.

S&F Decorative ultra slim liner LED Lighting fixture with extruded polycarbonate envirmental friendly, energy efficient tube light fitting including complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of 1.5Sqmm with suitable size of 18 Watt complete all as specified and directed .

S&F recess mounting LED flat panal 2'x2' made of CRCA sheet duly power coated with High effcient 36 watt LED complete with all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable of suitable size complete all as specified and directed. Notes for Srl item No 90 to 93:- 1. Driver shall be potted antivibration type. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be povided. 3. CRI (Colou Rendring Index) of fixture shall be > 70. 4. CCT (Colout Correlated Temprature of fixture shall be 5700K ± 300 K. 5. System Lumen Efficacy shall be > 100Lm/W 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 5 years gurantee shall be provided by contractor suppoted by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the Contractor shall replace / repair the defective fitting within 07 Days after handing over to Contractor for replacement / repair 11. CA No shall be written on each fitting before installation. 12. The name of manufacturer to be embossed on the fitting. 13. The fittings shall have arrangement so that maintaince required, if any can be carried out from Top cover.

S&F for MCB single pole (SP) 240 volts, 6 to 32 Amps, 10KA (C-series) , complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F MCB single pole (SP) 240 volts, 40 to 63 Amps, 10KA (C-series) of approved make complete all as specified and directed.

S&F Double door MCB DB SPN 240 Volts, 16 Way made out of CRCA powder coated sheets, IP43 protection with copper bus bar, including taking out old unserviciable DB any size/type, complete all as specified and directed.

S &F RCCB Single pole & neutral 240 Volts, 63 Amps and sensitivity 30mA, with breaking capacity of 10KA complete all as specified and directed. Make : Legrand/Schneider/Hager

S & F for sheet metal enclosure double door for distribution board (When MCB's are to be used) triple pole and neutral 415 Volts 4 way with 200 Amp rated busbar complete all as specified and directed. Make : Legrand/Schneider/Hager

S &F MCB triple pole & neutral 415 Volts, 63 Amps with breaking capacity of 10KA complete all as specified and directed. Make : Legrand/Schneider/Hager

M&L for Sub main wiring with FRLS PVC insulated unsheathed 2X4 sqmm multistranded copper conductor cable 1100 V with 1X4 sqmm FRLS PVC insulated green multistranded copper cable for continuous earth drawn through & including concealed PVC conduit of appropriate size not less than 20 mm dia & 1.8mm wall thickness with all accessories including cutting grooves and making good disturbed surface to match existing including taking down existing surface sub main wiring complete all as specified and directed. (Note: Two runs of FRLS PVC cable with one run of earth conductor and conduit shall be measured as one RM.) Make for wiring : Polycab/Anchor/Finolex

M&L for earthing complete with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in the ground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below ground level connected to galvanized iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point, HDPE pipe 15mm bore as protection pipe, GI watering pipe 20mm bore light grade with funnel and wire mesh, charcoal and salt, 40mm thick pre-cast RCC (1:2:4) type B-0 (Nominal mix) cover reinforced with XPM (weighing n.less than 4 Kg/Sqm) with suitable steel handle, and angle iron 40X40X3mm frame and chamber of PCC (1:3:6) type C-0 (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing on completion, all as shown on electric plate No. 03 of SSR-2009 Part-I, complete all as directed. Notes: 1. Earth lead & protection pipes length upto & including 7.50 metre is deemed included in unit rate quoted by the contractor. 2. Earth filling shall be done by vegitable soil. 3. Soil shall be free from stone, boulders, aggregate, gravels .

Supply , laying, testing and commissioning for 1100 volt grade XLPE insulated heavy duty cable, 16 sqmm 4 core, strip armoured with aluminium stranded conductor overall PVC sheathed laid in trenches including taking down existing cable & bricks complete all as specified and directed. Note : Excavation & Earthwork shall be measured and paid separately.

M & L for sand filling in trenches dry and and clean sand unwashed including punning around cable for protection of under ground cable complete all as specified and directed. [Note : Punned thickness shall be measured and paid]

M & L for well burnt bricks , laid flat ( old size) sub class B designation 75 for cable protection complete all as specifed and directed.

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation etc (for cable, pole stay manhole etc), in any type of soil and getting out, complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25cm thick, etc complete all as specified and directed.

Removing excavation material n exc. 50m & deposited where directed at a level n exc. 1.5m above the starting point etc complete all as specified and directed.

BALI ENTERPRISES

M/S J N TRADERS

SIDDAHANT ENTERPRISES

s k construction co

M/S VIJ CONSTRUCTION CO