Applying Thermoplastic paint at different T.P. and other different places for upcoming SBM and other different programs at Maninagar ward South Zone

surface providing and laying a hot applied thermoplastic compound

mm thick including reflectorising glass beads @ 250gms per sqm area,

thickness of 2.5mm is excluding of surface applied glass beds as per

1 2860 IRC:35-2015. The finished surface to be level, uniform and free from 559 Smt

streaks and holes. zebra patta /bump patta lane/center line/ edge

line/cut patta. The white color marking should provide liminance

coefficinet on cemend road shalll be min 130 mcd/m2/lux and Asphalt

road shall be min 100 mcd/m2/lux during the service life during the day

time. The marking should meet the performance criteria for night time

reflectivity, wet reflectivity and skid resistance as mentioned in the

section-15 of IRC 35-2015. (As per approved R.A)

Providing and laying Road marking with hot applied thermoplastic paints

strictly of Automark - "Specsmark", Asian Paints-"Apcomark", Katalline-

"Traffix O" or Berger Paints-"Sigmark" with reflectorising glass beads of

Automark-"Autolux Gold", "Swarco", "Sovitec" Asian Paints-Apcobids",

"Potters" on bitumin surface providing and laying a hot applied

thermoplastic compound 2.5 mm thick including reflectorising glass

beads @ 250gms per sqm area, thickness of 2.5mm is exclusive of

surface applied glass beds as per IRC:35. The finished surface to be level,

uniform and free from streaks and holes.) Directional Arrow, Lettering (1

word - up to 4 letters), or any kind of Artwork etc. (which shall

maximum size upto 2.75 Sqmt out to out) Item shall include providing

Stencils for lettering, direction arrow signages, and as per requirement.

including cleaning, required maintenance, etc. complete pre and post

work. Cost shall also include laying with applicator machine & operating

boilers, Skilled Labours for road marking, and Un-Skilled labours for

barricading/protection, traffic diversion, and it shall also include wastage

of material, etc. Contractor shall be responsible to run his own

thermoplastic applicator machine & supply necessary diesel, gas, fuel,

CAT EYE/Road Stud/RPM: Supplying of Moulded Twin Shank Raised

Pavement Markers made of polycarbonates and ABS moulded body and

reflective panels with Micro Prismatic Lens(No Glass Bed Lens) capable

of Providing total internal reflection of the light entering the lens face

and shall support a load of 13635 kgs. tested accordance to ASTM D

4280 Type H and complying to specification of category A of MORTH

Circular NO RW/NH/33023/10-97-DO lll Dt.11.06.1997. The height,

width and length shall not exceed 20 mm,130 mm and 130mm and with

3 20 minimum reflective area of 13 sqcm on each side and slope to the base 323 Nos.

shall be 35+/-5 degree.The strength of detachment of integrated

cylindrical shank,(of diameter not less than 19+/-2 mm and height not

less than 30+/-2 mm) from the body is to be a minimum value of

kgf. Fixing will be by drilling holes on the road for the shank to go inside,

without nails and using epoxy resin based adhesive as per

manufacturer's recommandation and The color of the marker should be

as per the IRC 35-2015 and as directed by Engineer-In-charge.(R&B SOR

2023-24 Item code:26162A)

Providing and applying primer before hot applied thermoplastic paints

marking on RCC road surface, which must ensure better adhesion of

thermoplastic paint to the surface and also increase paint durability,

4 217 including all material, manpower, tools and machineary required for 47 Smt

work, with all required safety standards to work in running traffic

conditions, as per standards and as instructed by engg in charge Agency

has to quote rate on Sq.Mt. work basis).(As per approved R.A)

Providing & applying C.R. Base Road Marking Painting lines, dashes,

arrow, letters etc. on Road in two coats on new Work with ready mixed

road marking paint conforming to IS:164 and AASHTO standard M-248-

90 on concrete/ bituminous surface,including required additive/ solvent,

providing safety cones,barricades, string, chalks or req. colour for line

marking,etc. Cleaning the surface, removing of all dirt , dust & other

foreign matter and clear the site as per engineer incharge.(As per

Estimated Tender Amount: Rs.