SPL REPAIRS TO BLDG NO P-46 AT MD ACCN ZONE 7A, ROOF TREATMENT AND BATHROOMS OF BLDG NO P-59, P-60, P-61 AND P-62 OF NAA UNDER GE (N) TEZPUR

Amount

Dismantling asbestos cement sheet, ridge (corrugated, semicorrugated, plain etc.) in roof coverings, walls, ridges etc. or of similar types complete in all respect as specified and directed.

Roughening surfaces of old concrete floor by picking sweeping clean , and washing down with water to remove dust complete all as specified and directed

Dismantling of floor/ wall tiles including cement mortar bedding of any thickness upto PCC/ RCC/brick surface and rubbish off the premises, complete in all respect all as specified and directed.

Dismantalling of cement concrete (unreinforced) in ground floors and pavings not exceedings 15 cm thickness (below or above ground level), complete in all respect as specified and directed.

Dismantalling of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete in all respect as specified and directed.

Taking down shutter exc 1 sqm and n. exc 2 sqm each, complete in all respect as specified and directed.

Taking down chowkats and shutters (without taking off shutters from the frame) n.exc 1.5 sqm each, complete in all respect as specified and directed.

Taking down shutter and refixing in same opening after easying exc 1 sqm and n. exc 2 sqm each, complete in all respect as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm and n.exc 4 sqm each, complete in all respect as specified and directed.

Taking down cement plaster of any thickness and description on brick/ concrete/ stone wall/ ceilings, etc, including raking out joints, hacking for key, scrubbing down with water etc, complete in all respect as specified and directed.

Demolition and breaking up drain pipes 75 mm/110 mm bore dia (Salt glazed ware, PVC or Reinforced concrete) set in cement mortar, complete in all respect as specified and directed.

M&L for brick work with sub-class "B" old size bricks of class designation (CD) 75, straight or curved on plan exc 6m mean radius, built in cement mortar (CM) 1:6, including dismantalling of brick work built in cement mortar in any position, complete in all respect as specified and directed.

M&L for half brick work with subclass ‘B’ old size bricks of class designation 75, straight or curved on plan exc. 6m mean radius built in CM (1:4) including dismantalling of brick work built in cement mortar in any position, complete in all respect as specified and directed.

S&F pressed steel door frame for doors with one or more rebates incl necessary fixing lugs , hinges ,lock strike plate , etc size 125x60 mm incl PCC filling all as specified and directed.

S&F pressed steel door frame for doors with one or more rebates incl necessary fixing lugs , hinges ,lock strike plate , etc size 105x60 mm incl PCC filling all as specified and directed.

S & F mild steel sections (Beam, tee, angle, channel, tee, angle, tubular/hollow section or flat sections) in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing, independent fixing with welding etc. including distance pieces, cleats etc. using Fe 410-W (Gde E-250) quality A complete in all respect as specifified and directed.

Expanded metal, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members complete in all respect as specifified and directed.

S & F second class hardwood plain,solid ,straight,chowkats and frames,wrought, framed rebated on the solid ,rounded or chamfered,put together with glue pinned at joints, complete in all respect as specified and directed.

Providing and laying for cement concrete in coping, hold fasts using type B-1, 1:2:4 (using 20 mm nominal size crushed and graded stone aggregate) or of similar type of work including necessary formwork complete in all respect as specified and directed.

S&F coloured 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based trapezoid profile steel sheet having tensile strenght of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws with bitumen washer to truss members of any material, complete in all respect as specified and directed.

S&F coloured 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based trapezoid profile steel sheet having tensile strenght of 550 Mpa as in ridge, valley gutter or of similar type, fixed with self tapping screws with bitumen washer to truss members of any material, complete in all respect as specified and directed (The measurement shall be carried out as in a plain sheet).

S&F coloured 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based plain steel sheet having tensile strenght of 550 Mpa as in eves covering or of similar type, fixed with self tapping screws with bitumen washer over mild steel flats, angles etc. and screws for fixing with framed structure complete in all respect as specified and directed. (Note:- MS work shall be measured and paid separately).

S&F exposed GI powder coated snap grid frame work for false ceiling in flat or in sloping, of grid size 600 x 600 mm comprising of wall/ cleat angle of size 25x25x0.35 mm and corss tee of size 24x38x0.70 mm with 4 mm dia GI wire as suspender and including 4 mm thick decorative pre-painted non asbestos board (E-Board) in false ceiling including fixing arrangement from steel/ wooden truss of any type including dismantling of existing false ceiling boards, complete in all respect as specified and directed. (Make:- Eternit, Everest or equivalent)

Providing and laying skid/non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floor etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick screed bed in cement mortar (CM) 1:6, complete in all respect as specified and directed.

Providing and laying coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.08 sqm but not exceeding 0.15 sqm, in skrting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick rendering in cement mortar (CM) 1:4, complete in all respect as specified and directed.

Providing and laying skid/non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick screed bed in cement mortar (CM) 1:6, complete in all respect as specified and directed.

M&L for any colour of granite stone without white spots Granite stone slab 20 mm thick, as in floor, dado, steps, laid over and including screed bed 15 mm thick in cement mortar (CM) 1:6, jointed and pointed with white cement mixed with pigment to match the shade of stone including cuttingl rubbing and polishing surface, including cutting for wash hand basin, sink, gas pipe hole etc., to the entire satisfaction of the Engineer-in-Charge, complete in all respect as specified and directed.

M&L for 20-25 mm thick machine cut kota stone single piece in staircase over 15 mm thick cement mortar (CM) 1:6 screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete in all respect as specified and directed.

M&L for 20-25 mm thick machine cut kota stone slab single piece in riser of steps, skirting, dado and pillar over 15 mm thick rendering in cement mortar (CM) 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete in all respect as specified and directed.

Material and labour for Cleaning and preparation of roof/wall (RCC/BRICK/tiles/Cement cuncrete) surface and made free of dirt, foreign particles, laitance followed by grinding all protrusions to make surface modulated. Thereafter, inspection for cracks on the surface ceused by thermal expansion/ contraction and repairing the cracks on the surface caused by thermal machine, filled with Repair Mortar/General purpose Grout in the proportions as recommended by manufacturer, supplying and applying High performance Hybrid Polyurea waterproofing coating spray/hand applied liquid membrane including taking of existing roof treatment and apply with following specifications: (a) Elongation of range 400% 600% (b) Tensile strength of 8-12 N/mm2. (c) Crack bridging ability of 3.00-4.00mm (d) Hardness (Shore 'A' ASTM D2240) of range 50-70 The application shall include final base preparation, epoxy primer application in rato 1.1 (resin: hardner) with 100% water dilution and application of Hybrid polyurea in two coats in 6 hrs interval to achieve total min thickness 1 to 1.50mm. The application/ treatment shall be carried out by authorized rep of approved specialist firm/manufacturer Make- SIKA/FOSROC/Asian Paints/Berger. Note: The defect liability period of water proofing treatment shall be 10 years and the contractor shall beespor building(s) free From leakage/seepage for a period of completion. The contractor may obtain a similar guarantee by him for the purpose. 10 years after certified date of completion. the contractor may obtain a similar guarantee from the specialist firm engaged by him for purpose.

Taking down existing damaged IWC alongwith complete PCC and cement concrete from sunken floor and providing new IWC and water proofing treatment to sunken floor as per following stages:- (d) S&F in repair vitreous chinaware sqatting pan of size 580 x 440 mm, 'ORISSA PATTERN' with new PVC 'P' or 'S' trap and cement filling (1:5:10) and 25 mm thick PCC 1:2:4 at top surface bedded in cement concrete (excluding flushing cistern and flush pipe) with integral foot rests, complete in all respect as specified and directed. (Waterproofing treatment shall be paid separatly)

M&L for waterproofing treatment to RCC sunken slab as specified below. Make: PIDILITE or equivalent. (a) creating fillet coving of 50mmX50mm with polymer modified mortar using cement : sand : URP (b) Applying PU sealant at the junction of pipes and the RCC surface. (c) Apply1st coat of two component cementitious coating, over the surface and taking the coating on the walls over the angle fillet / watta portion. (d) Lay 40gsm geotextile fleece at the watta portion. (e) Apply 2nd coat of two component cementitious coating, over the first coat and taking the coating on the walls over the angle fillet / watta upto 1M after 6 -8 Hrs. (f) Applying 12mm thick plaster in C:M 1:3 with waterproofing compound conforming to IS 2645:2003 @ 250ml per bag of cement.

M&L 15 mm thick plastering on brick/ stone/ concrete surfaces of wall in cement mortar (1:4), finished even & smooth without using extra cement, complete in all respect as speicifed and directed.

M&L 15 mm thick plastering on brick/ stone/ concrete surfaces of of wall in cement mortar (1:6), finished even and smooth without using extra cement, complete in all respect as spefied and directed.

M&L 10 mm thick plastering on brick/ stone/ concrete surfaces of ceiling in cement mortar (1:3) finished even and smooth without using extra cement, complete in all respect as specified and directed.

Supply only water proofing compound complete, in all respect as specified and directed.

S&F 16mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches with all fittings fixed complete to walls and ceiling or laid in floors including necessary cutting, chasing etc complete all as specified and directed.

S&F 20 mm bore of tubes, 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors including taking up or down including necessary cutting, chauging etc. complete in all respect as specified and directed.

S&F in repair 20 mm bore of Gun-metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe and fixed, complete in all respect as specified and directed.

Providing and fixing in position kitchen cup board box type as per design and directed of 550-600mm deep, fixed over wall with PVC gittie and screws/or in beneath of kitchen counter, cup board, kitchen cabinet in required sizes as per site made out of 17-18mm thick one side decorative lamination and other side balancing lamination sheet consisting of carcass 17-18mm thick PVC sheet. Provision of shelves, shutters, back side, top, bottom, side, made out of 17-18mm thick one side decorative laminated PVC sheet , all required brackets, screws etc,. The panel shall be fabricated using adhesives and screws whereever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per maufactures specifications and drawing including 15mmX20mm medium grade chrome finish two nos per leaf, slip on cabinet hinge/self-closing hinge, soft close hydraulic 4 hole cabinet auto cup hinge full overlay O crank with soft closing of make Godrej/Avis L Bihari/Hettich/Harrison and 50mm SS handle size all items each per shutter complete in all respect as specified and directed. Make: Rajshri Plastiwood, Sintex or of appd make. (Note: For payment, measurement shall be taken as front portion of cup board measurement only, rest other items/materials as specified shall not be measured or paid as these are included in this item)

Providing and fixing in position kitchen cup board box type as per design and directed of 250-300mm deep, fixed over wall with PVC gittie and screws/or in beneath of kitchen counter, cup board, kitchen cabinet in required sizes as per site made out of 17-18mm thick one side decorative lamination and other side balancing lamination sheet consisting of carcass 17-18mm thick PVC sheet. Provision of shelves, shutters, back side, top, bottom, side, made out of 17-18mm thick one side decorative laminated PVC sheet , all required brackets, screws etc,. The panel shall be fabricated using adhesives and screws whereever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per maufactures specifications and drawing including 15mmX20mm medium grade chrome finish two nos per leaf, slip on cabinet hinge/self-closing hinge, soft close hydraulic 4 hole cabinet auto cup hinge full overlay O crank with soft closing of make Godrej/Avis L Bihari/Hettich/Harrison and 50mm SS handle size all items each per shutter including complete in all respect as specified and directed. Make: Rajshri Plastiwood, Sintex or of appd make. (Note: For payment, measurement shall be taken as front portion of cup board measurement only, rest other items/materials as specified shall not be measured or paid as these are included in this item)

S & F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. or for window grill of appd size and shapeincluding fixing with aluminium "U" shape section for fixing etc. complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S & F powder coated aluminium window and ventilator shutters, side hung type with/without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, EPDM rubber packing (of 50 No) grade), powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21, 100mm long (2 no.) suitable handle (1 no.) complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S & F powder coated aluminium sliding window with/without sash bars, aluminium sections of thickness 1.5mm including necessary joining cleats, glazing clips, EPDM rubber packing (of 50 No grade), powder coated aluminium snap beading, screws, center grooved stainless steel ball-bearing double roller 2 position height adjustment, sound/dust brush, recessed handle with locking arrangement complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S & F powder coated aluminium ventilator with half portion louvered (adjustable)with 4mm thick glass in louver and balanced portion fixed 4mm thick frosted glass glazing including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings complete in all respect as specified and directed.

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in- charge.

S&F 75 mm size of butt hinges stainless steel, complete in all respect as specified and directed.

S&F 100 mm size of mild steel butt hinges ISI marked, complete in all respect as specified and directed.

S&F for solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, supplying & fixing in opening as per specification & drawing, complete in all respect as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel haivng a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and botom rail on either side & as gap insert for top rail & bottom rails; Panelling of plain colour PVC sheet to be fitted in the M.S. frame weloded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling and fixing in the frame at site as per specification & drawing, complete in all respcet as specified and directed.

S&F 35mm thick second class HW glazed and skeleton shutters, open rebated and prepared to receive glass gauge etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass etc.; sizes of members of shuttrs as specified in SSR Part-I, section 8, clause 8.24 (a), complete in all respect as specified and directed.

S&F 4 mm thick figured glass, pin head type and glazing with oil putty in square n.exc 0.5 sqm in each pane, complete in all respect as specified and directed.

S&F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq.m in each pane, complete in all respect as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width aperture 1.40 mm and fixed with stainless steel wire staples fixing withbeads, complete in all respect as specified and directed.

S&F 25 mm thick Flush shutters, solid core construction, with block board core with decorative face veneers withlipping on both sides, complete in all respect as specified and directed.

S&F 30mm thick Flush shutters, solid core construction, with block board core with decorative face veneers with lipping on both sides, complete in all respect as specified and directed.

S & F 18-19mm block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work including necessary leaping/edge margin of 3mm thick complete in all respect as specified and directed.

S&F aluminium anodised, barrel tower bolt of extruded section 200 mm long, complete in all respect as specified and directed.

S&F Aluminium handle cast type anodised 125 mm, complete in all respect as specified and directed.

S&F aluminium anodised sliding door bolts with hasp and staple (boilt type) 16 mm dia bolt, 250 mm long, with and including a minium of 6 bolts and nuts four on bolt plate and two on staple plate, complete in all respect as specified and directed

S&F mild steel 300 mm, ordinary rat tail rod pattern springs, including roller and roller plate, complete all as specified and directed.

S&F SS 20 mm dia curtain rod with fixing bracket, stops, rollers etc. complete all as specified and directed.

S&F plate rack made out of stainless steel sheet 0.50 mm thick overall size 900 mm (W) x 760 mm (H) x 250 mm (D) with three shelf, complete in all respect as specified and directed

Fixing only plate rack made out of stainless steel complete in all respect as specified and directed

S&F sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to drarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm, complete in all respect as specified and directed. Make : Jayna, Neelkhanth, Nirali

Dismentalling & fixing in repair Sink kitchen with plugs, washers and wastes; including beding in cement mortar on to dwarf walls, or including fixing cantilever brackets and connecting union to waste pipe; upto 0.5 sqm each complete in all respect as specified and directed

S&F three layered white in colour rotational moulded made out from LLDPE material water storage tanks of capacity 1000 ltr (cylindrical vertical with closed top) including three tank nipples of 20 mm nominal bore dia hoisted and fixed in position including dismantling/ taking down all as specified in SSR part I, complete in all respect as specified and directed. Make:- Sheetal (Virat), Sintex, Oriplast, Supreme

Disconnecting existing 500 Ltr tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately)

S&F PTMT ball valve high pressure 20 mm bore with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe, complete in all respect as specified and directed.

S & F in repair 15mm bore concealed long neck , CP finished stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete in all respect as specified and directed.

S&F in repair vitreous chinaware sqatting pan of size 580 x 440 mm, 'ORISSA PATTERN' with new PVC 'P' or 'S' trap bedded in cement concrete (excluding flushing cistern and flush pipe) with integral foot rests, complete in all respect as specified and directed.

S&F in repair PVC valveless, syphonic action type, low level dual flush cistern 10 ltr capacity, white, wtih inlet, ball valve, float and handle including brackets & flush pipe of polyethylene for low or high level cistern of required height of high density PVC, 32 mm dia pipe, complete in all respect as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm, complete in all respect as specified and directed.

S&F in repairs 15 mm bore fancy type CP finished angle valves, cast copper alloy, screwed down, high pre-ssure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete in all respect as specified and directed.

S&F in repairs long body Bib taps of 15 mm bore, fancy type CP finish cast copper alloy with crutch handle, screwed down, screwed for iron pipes, complete in all respect as specified and directed.

S&F in repairs short body Bib taps of 15 mm bore, fancy type CP finish cast copper alloy with crutch handle, screwed down, screwed for iron pipes, complete in all respect as specified and directed.

S&F in repair for 15 mm bore pipe brass chromium plated (CP) shower rose 125 mm size, fixed to iron pipe, complete all as specified and directed.

S&F Tubular towel rail, 20 mm dia, D type, 60 cm long between flanges cast copper alloy, chromium plated finish, complete in all respect as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long, complete all as specified and directed.

S&F in repair wash hand basins (WHB), vitreous china of size 550x400 mm (flat back or angle back type), including cutting for and pinning in ends of brackets over new angle iron erecting stand embedded in PCC (1:2:4) block including 32 mm dia bore waste fittings cast copper alloy chromium plated with long screwed shanks and flynuts flange and beded in redlead cement, incl 32mm SS Bottle trap including 15 mm bore dia fancy type CP finish pillar tap, cast copper alloy with capstand heads, screw down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screw for iron pipes complete in all respect as specified and directed.

Fixing in repair Wash basins, Vitreous China (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed

S&F Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed

S&F 75 mm dia of outlet, PVC (SWR) nahani trap, plain with SS grating of size 150mmX150mm, 0.75mm thick openable at center including jointing with solvent cement, complete in all respect as specified and directed.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110mm bore including necessary MS pipe clamp, complete in all respect as specified and directed.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 75mm bore including necessary MS pipe clamp, complete in all respect as specified and directed.

S&F PVC (SWR) pipes single sockedted in any length with rubber ring joints laying in trenches 110 mm bore, complete in all respect as specified and directed.

S&F PVC (SWR) pipes single sockedted in any length with rubber ring joints laying in trenches 75 mm bore, complete in all respect as specified and directed.

S&F PVC (SWR) single (single 'T') equal or unequal 110mm bore pipe with access door, complete in all respect as specified and directed.

S&F PVC (SWR) single (single 'T') equal or unequal 75mm bore pipe with access door, complete in all respect as specified and directed.

S&F PVC (SWR) bends any radius 110 mm bore, complete in all respect as specified and directed.

S&F PVC (SWR) bends any radius 75 mm bore, complete in all respect as specified and directed.

S&F PVC (SWR) vent cowl 110 mm dia bore, complete in all respect as specified and directed.

S&F PVC (SWR) vent cowl 75 mm dia bore, complete in all respect as specified and directed.

Supply and fixed unplasticised PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 160mm outside diameter as per IS:13592-1992 including dismantling and breaking up existing drain pipes and fixing necessary mild steel pipe clamps complete in all respect as specified and directed. Make: Supreme Type A, Prince, Oriplast.

Supply and fixed unplasticised PVC (SWR) bends any radius for160mm outside diameter of pipe as per IS:14735-1999 complete in all respect as specified and directed. Make: Supreme, Prince, Oriplast.

Supply and fixed unplasticised PVC (SWR) junction single, (single Tee) equal or unequal for160mm outside diameter of pipe as per IS:14735-1999 complete in all respect as specified and directed. Make: Supreme, Prince, Oriplast.

Supply and fixed unplasticised PVC (SWR) Gully trap 125/110 mm, setting and jointing with solvent cement complete in all respect as specified and directed. Make: Supreme, Prince, Oriplast.

M&L for precast RCC, type B-1, 1:2:4 (using 20 mm crushed and graded stone aggregate) as in manhole covers/ cover slabs or of similar type slab works, etc. incl necessary formwork and loading/ unloading of the same and fixed in position, complete in all respcet as specified and directed.

Providing and laying reinforced concrete slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like using 1:2:4 type B-1, (using 20 mm crushed and graded stone aggregate) complete in all respcet as specified and directed.

M & L for formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all not exceeding 20cm wide complete in all respcet as specified and directed.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete in all respcet as specified and directed.

S&F 10 mm dia and over TMT bar cut to length bent to shape required including cracking bending spiarlly for hoping for columns, hooking ends and binding with and including Mild Steel wire (annealed) not less than 0.90 mm dia or securing with clip, complete in all respect as specified and directed.

M&L for plinth protection or in foot path of 75 mm thick of cement concrete using type C-1, 1:3:6 (using 20 mm nominal size crushed and graded stone aggregate) in alternate penals and finished fair and even complete in all respect as specified and directed.

M&L for PCC 1:3:6 type C1 (using 20mm nominal size crushed and graded stone aggregate) as in surface channels & drains complete in all respect as specified and directed.

M&L for preparation of old decorated plastered surface of wall after complete removal of existing treatment and applying two coats of weather coat over 2 mm thick wall care putty (in two layers) over a coat of primer including preparation of surface, complete in all respect as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of weather coat over 2 mm thick wall care putty over a coat of primer including necessary preparation of surface, complete in all respect as specified and directed.

M&L for complete removal of existing treatment on wall and applying two coats of oil bound distemper (OBD) and finished another one coat with spunge roller over one coat of alkali resistant priming paint over 2 mm thick (in two layers) wall care putty, complete in all respect as specified and directed.

M&L for preparation of newly undecorated plastered surface of wall and applying two coats of oil bound distemper (OBD) and finished another one coat with spunge roller over one coat of alkali resistant priming paint over 2 mm thick (in two layers), wall care putty, complete in all respect as specified and directed.

M&L for preparation of old decorated plastered surface of ceiling and applying two coats of oil bound distemper including filling of voids with wall care putty on plastered surface including complete removal of existig treatment, complete in all respect as specified and directed.

M&L for preparation of newly plastered surface of ceiling and applying two coats of oil bound distemper including filling of voids with wall care putty on plastered surface, complete in all respect as specified and directed.

M&L for preparing of new undecorated wooden surface, of any description, not otherwise described, overe 10 cm width or girth, and applying two coats of synthetic enamel paint over a coat of pink primer, complete in all respect as specified and directed.

M&L for preparation of new undecorated steel surface of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete in all respect as specified and directed.

M&L for preparing of old decorated wooden surface, of any description, not otherwise described, over 10 cm width or girth, and applying two coats of synthetic enamel paint, complete in all respect as specified and directed.

M&L for preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with creosote oil, complete in all respect as specified and directed.

M&L for preparation of old decorated steel surface of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint, complete in all respect as specified and directed.

M&L for cement concrete Type D-2, 1:4:8 (using 40mm nominal size crushed and graded stone aggregate) in foundations filling and mass concrete as in surroundings of fencing post etc. complete in all respect as specified and directed.

M&L for sand filling under floor or below paver blocks incl. watering and consolidation complete in all respect as specified and directed.

Removing and re-fixing for 55-60mm thick coloured, glazed pre coated interlocking or without interlocking paver block of any shape and size confirming to IS 15658/1237 with upto date amendments, M-35 Grade with grey cement with pigment laid over and including fine river bed sand complete in all respect as specified and directed. Sample as approved by GE.

M&L in repairs for for 55-60mm thick coloured, glazed pre coated interlocking or without interlocking paver block of any shape and size confirming to IS 15658/1237 with upto date amendments, M-35 Grade with grey cement with pigment laid over and including fine river bed sand complete in all respect as specified and directed. Sample as approved by GE.

M&L for 25 mm thick of cement concrete flooring using type B 0, 1:2:4 (using 12.5 mm nominal size crushed and graded stone aggregate) and finished fair and even without using extra cement, complete in all respect as specified and directed.

Supplying and laying 20mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as respect as specified and directed.

S&F three layered white in colour rotational moulded made out from LLDPE material water storage tanks of capacity 500 ltr (cylindrical vertical with closed top) including three tank nipples of 20 mm nominal bore dia hoisted and fixed in position including dismantling/ taking down all as specified in SSR part I, complete in all respect as specified and directed. Make:- Sheetal (Virat), Sintex, Oriplast, Supreme

Taking down existing damaged IWC alongwith complete PCC and cement concrete from sunken floor and water proofing treatment to sunken floor as per following stages:- (a) creating fillet coving of 50mmX50mm with polymer modified mortar using cement : sand : URP (b) Applying PU sealant at the junction of pipes and the RCC surface. (c) Apply1st coat of two component cementitious coating, over the surface and taking the coating on the walls over the angle fillet / watta portion. (d) Lay 40gsm geotextile fleece at the watta portion. (e) Apply 2nd coat of two component cementitious coating, over the first coat and taking the coating on the walls over the angle fillet / watta upto 1M after 6 -8 Hrs. (f) Applying 12mm thick plaster in C:M 1:3 with waterproofing compound conforming to IS 2645:2003 @ 250ml per bag of cement.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete in all respect as specified and directed.

S&F Brass CP mixer for mixing hot & cold water screwed down for iron/CPVC pipe and fixed complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in eves covering or of similar type, fixed with self tapping screws including necessary mild steel flats and screws for fixing with framed structure complete all as specified and directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, tubular/hollow section, channel or flat sections) including distance pieces, cleats etc. using FE-410W (Grade E-250 quality "A") complete all as specified and directed.

Providing and applying spray applied two component pure polyurea with 100% solid content, elongation minimum 450 %. The mixing of two component should be 1:1 by volume & 1.5 mm DFT t be obtained. The polyurea to be applied after surface preparation & application of solvent based epoxy primer. The consumption of primer should be 250ml per sq.mt but may vary as per surface porosity. The surface moisture should be below 5% before application. The work should be executed by company authorised applicator.

Taking down carefully aluminium / copper point wiring any type for one light , fan, socket power point or buzzer controlled by one switch complete including fitting / fixtures such as switches, ceiling roses, holder, socket, light fitting etc and making good disturbed surfaces of walls, ceilings etc.

Taking down main switches and DBs of any type and make including wooden board/ junction box.

Taking down burnt/unserviceable sub main wiring any size complete and making good disturbed surfaces of walls all as specified and directed.

All as per item No. 133 here-in- before but for 3 pin 5 Amps switch socket combination on independent board with 1.5 sq mm copper cable.

All as per item No. 133 here-in- before but for 3 pin 16 Amps switch socket combination on independent board with 4.0 sq mm copper cable

All as per item No. 133 here - in - before but for 5 Amps socket point on the same board controlled by one switch.

All as per item No. 133 here - in - before but for one light point controlled by two, two way switch with 1.5 sq mm copper conductor cable.

S & F Modular switch 1 way 6 A ,1 module complete all as directed.

S & F Modular switch 2 way 6A, 1 module complete all as directed.

S & F Modular Bell push 6A 1 module complete all as directed.

S & F Modular Fan step regulator, 120W - 2 module complete all as directed.

S & F for ceiling rose surface bakelite 3 phases polycarbonate isolated body

S & F Modular Socket 6 A 2/3 pin combined , 2 module complete all as directed.

S & F Modular Socket 6 A /16 A-2/3 pin combined 2 module complete all as directed.

S & F Modular Switch 16 Amp 1 module complete all as directed.

S & F for white cover plate with frame 8 module

S & F for white cover plate with frame 3 module

S & F for white cover plate with frame 6 module

S&F call bell, Ding dong type, AC 230 Volts single pole

S &F modular TV coaxial socket outlet fixed in 1 M box comprising of flush metal box inner plate and outer cover plate complete all as specified

Supply & Fix PVC Conduit 25 mm for TV cable and telephone cable Nos including all accessories complete all as specified and directed

Material and Labour for Lamp holder, PVC/Polycarbonate batten type complete all as specified and directed.

Supply and fix LED BALL LAMP of 10W with lumen output not less than 900 lm and colour temp 6500K complete all as specified and directed.

Supply and fixing mirror light batten type 1x5W 230V AC, 50Hz ,Pf >0.98 , THD <10% complete all as specified and directed by Engineer in charge.

Supply and fixing LED luminaires, 22 watts, lumen output not less than 2000 (4 feet), made of anodised extruded aluminium housng, with high transmissivity diffuser, high lumen output not less than 2200, with suitable electronic driver, and operated in single phase, 230 volts, 50HZ, all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable of size 23/0.0076, from connector and ceiling rose, complete all as specified and directed.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size

Supply and fixing single pole and neutral enclouser with a two pin and earth plug and socket complete with one pole MCB 20 Amps complete all as spd and directed .

Supply, install, testing & commissioning of LT panel board "in-door wall mounting type" factory fabricated (CPRI type tested) with suitable neoprene rubber gasket to make it completely dust & vermin proof & degree of protection not less than IP-43 & general construction confirming to IS-13947, double door, front openable. The panel shall be provided with ventilation facility in the form of louvers for better heat dissipation & tinned copper bus-bar wrapped with coloured PVC tape/sleeves of rating in conformity to the Incoming MCCB rating. The panel board shall be fabricated out of 2.0 mm thick CRCA sheet duly pre-treated & powder coated, supporting frame made out of suitable size angle iron/channel etc. suitable for 3 Ph, 4 wire system 415/440 volts grade incl complete internal wiring with not less than 2.5 sqmm copper wire incl cable glands of suitable sizes incl arrangements for wall mounting complete all as specified & as directed with &incl the following accessories:- BUS-BAR & INTERNAL CONNECTIONS : The bus-bars shall be made up of 04 Nos Al 200 A rated, duly insulated with 1100 V grade standard colour coded PVC sleeves & rigidly mounted on suitable sized "F" class insulators of non-hygroscopic, non-combustible, all internal connections from main bus-bars to switch gears etc. PROVISION FOR CABLE ENTRY : The provision for cable entry/exit shall be provided in the bottom for both incoming& out-going cables. INCOMING : MCCB 4P (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting having breaking capacity 25 KA of rating 100 A incl electric connection complete. OUTGOINGS : (a) S & F MCB, DP, 10KA, 230V, "C" curve, 40 A, ISI Marked complete - 05 Nos (including one no. spare) (b) S & F MCB, DP, 10KA, 230V, "C" curve, 06 to 32 A, ISI Marked complete - 01 Nos. (c) Space for Single Phase prepaid KWH meter - 05 Nos. (d) Indicator lamp with integral circuit (230/240V) & cluster LED (Red, Orange, Blue) - 01 Set.

M&L for Earthing complete with GI plate electrode of size 600x600x6 mm thick buried directly in ground with earth pit not less than 3 meter deep below ground level with top edge of plate not less than 2.4 meter below normal ground level connected to GI earth wire 4mm dia earth lead up to 7.5 mtr by means of nuts, bolts, check nuts, washers of tinned brass, protected by galvanized iron pipe 20mm bore (Medium grade) all as directed including cement concrete (1:3:6) type C-1 earth pit with precast RCC (1:1.5:3) type A-1 cover slab of size 42 x 42 x10cm thick reinforced with 8mm dia TMT bars @ 15 cm c/c both ways with 10mm dia mild steel round bar of 30 cm long, bent to shape as lifting handle, funnel, wire mesh, 20 mm bore galvanized iron pipe (medium grade) for watering,including charcoal or coke and salt in alternate layers and filling earth pit with fresh vegetable soil below GI plate and above upto ground level as required and necessary earth work in soft/loose soil complete all as shown in electrical plate No 5 of SSR Part I including testing on completion all complete as specified and directed.

Supply and draw submain wiring with two single core 4 sq mm FRLSH PVC insulated copper cable 1100 volts grade multi stranded, sheathed conductor in concealed PVC conduit including 4 sq mm multi-strand FRLSH PVC insulated copper wire for earth continuity conductor connected to common earth dolly complete and making good disturbed surface complete. Note:- Cost of PVC conduit, cutting chases on walls and making good disturbed wall surfaces including finishing with cement mortar (1:4) matching with the existing shade / tint are deemed to be included in the rates quoted.

Supply and draw submain wiring with two single core 6 sq mm FRLSH PVC insulated copper cable 1100 volts grade multi stranded, sheathed conductor in concealed PVC conduit including 6 sq mm multi-strand FRLSH PVC insulated copper wire for earth continuity conductor connected to common earth dolly complete and making good disturbed surface complete. Note:- Cost of PVC conduit, cutting chases on walls and making good disturbed wall surfaces including finishing with cement mortar (1:4) matching with the existing shade / tint are deemed to be included in the rates quoted.

M&L for sheet metal enclosure for MCB DBs SPN 12 way 415 V, double door complete flush mounted all as specified and as directed.

M&L for Isolator single pole 5 to 32 Amps, 240 volts complete all as specified and directed.

M&L for Isolator DP 40 Amps, 240 volts complete all as specified and directed.

Supplying & fixing to walls and ceilings or laid in floors 25 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

S & F 25 mm gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed to pipe complete

Cutting galvanised mild steel pipe of nominal bore 20 mm to 50 mm for alterations or additions (each cut measured) including inserting complete all as specified and as directed.

NOTES: 1. All periodical and painting work including scraping down of existing treatments etc preparation of surfaces putty work and primer etc shall be carried out through mechanical means and as recommended by the manufacturer of the products. 2. The amount of schedule of credit shall be deducted from the total of this BOQ for arriving at contract sum. 3. The rates for RCC/PCC shall deemed to include the cost of formwork, shuttering etc., required for complete and proper execution of the item. Refer Schedule "A" notes for details.

D G Corporation (BID ID -3487837)

M/S Bharat Construction Co. (BID ID -3487201)

M/S RUSTAM ALI (BID ID -3488032)

M/S S.K. Sharma (BID ID -3493238)