Enquiry No I-12053/WEB/CONT/BT

Amount

Laying/Re-routing of 1.1KV grade PVC armoured cable of size Control cable of Size 2.5mm

Termination of 1.1KV grade cable 3.1/2C x 95 Sq.mm to 120 Sq.mm through suitable glands & lugs. The glands & lugs shall be supplied by the Contractor.

Termination of 1.1KV grade cable 4C x 16 Sq.mm. to 35 Sq.mm. through suitable glands & lugs. The glands & lugs shall be supplied by the Contractor.

Termination of 1.1KV grade cable 3.1/2C x 50 to 70 Sq.mm. through suitable glands & lugs. The glands & lugs shall be supplied by the Contractor.

Dismantling of Copper conducting tubes along with their clamps and without damaging the fixing bolts and nuts of SCF, R,Y & B phase electrodes

Dismantling of Flexible jumpers along with both ends lugs from mounting block & busbar without damaging the fixing bolts. of SCF, R,Y & B phase electrodes

Dismentalling of Mounting blocks from the existing position of the three electrodes (R,Y & B) without damaging their fixing studs and counter weight attachments

Fixing of the conducting tubes with the electrode pad clamps and mounting blocks by final bending of the tubes by heating them any stress/strain should not develop on the tubes after fixing. (The contact surfaces of the tubes should be cl

Termination of 4/3 C x 2.5 Sq.mm. cable by supplying suitable size of cable glands & lugs.

Erection, commissioning and fixing of ICTP switches upto 63A

Installation/testing & commissioning of TPN Switches above 63A upto 160A.

Installation/testing & commissioning of TPN Switches above 160A to 250A.

Installation/testing & commissioning of TPN Switches 300A to 750A.

Installation of ON/OFF push button station.

Installation/overhauling/repairing of DOL/ Star delta starter MCC & clelaning/painting of the cubicle upto 30HP motor.

Installation/overhauling/repairing of DOL/ Star delta starter MCC & clelaning/painting of the cubicle above 30HP to 125HP motor.

Dismantling, removal & shifjting from position to ERS safely & return back to position from ERS to site of Motors from 1HP to 20 HP (Appr. Wt. 5 Kg. to 40 Kg.)

Dismantling, removal & shifjting from position to ERS safely & return back to position from ERS to site of Motors from 25 Hp to 100 HP (approx. wt.from 40 Kg. to 200 Kg.)

Dismantling & refixing of 10" x 1" copper busbar

Opening of bolts, dismantling of busbar joints (10" x 1") (2 run joints pieces) double contract type, cleaning of surface of the joints & bussbar & refixing the same with proper alignment of busbarswith replacement of damaged bolts & nuts i

Opening of bolts, dismantling of busbar joints (10" x 1") (single joint type) double contract type, cleaning of surface of the joints & bussbar & refixing the same with proper alignment of busbarswith replacement of damaged bolts & nuts if

Replacement of epoxy mould insulator for busbar support wherever required job includes dismantling of busbar support clamp & fixing of new insulator in place of damaged one (Epoxy mould insulator will be supplied by HCL/ICC).

Replacement of busbar support clamps assembly (aluminium bronze) wherever required. Job includes dismantling of old clamp & replacement of new clamp with proper tightening (support clamp assembly will be supplied by HCL/ICC).

Replacement of 15/20A tumbler switches/toggle switches or Rotary switches. from the existing lighting/welding DBs or any other place & necessary painting of the DBs after tit bit repair.

Replacement of 15/20A Fuse base & carriers. from the existing lighting/welding DBs or any other place & necessary painting of the DBs after tit bit repair.

Replacement of 32/63A Fuse base & carrier from the existing lighting/welding DBs or any other place & necessary painting of the DBs after tit bit repair.

HPMV/HPSV lamp fittings.70W/80W & 125W/250W Dismantling, repair, rectification & fixing back with proper clamps, hooks etc.,and glowing after connection of existing fittings

Excavation of earth pit in any class of soil including stones, slag etc. by 15' deep & refilling with charcoal, salt & good quality of soil. Approximate 60 Kg. salt & 60 Kg. charcoal should be used for each earth pit. 65 mm NB, 3.5 mtr l

Dismantling of following sizes of cable from cable tray/underground & its reeling for further use. The sizes of cables as under:- 1.1KV grade PVC armoured PVC inner & outer sheathed AYFY type cable below 25 Sq.mm. including control & po

Laying/Re-routing of 1.1KV grade PVC armoured cable of size 3.1/2C x 95 to 120 Sq.mm. PVC armoured cable.

Unbolting & dismantling of copper busbar from its existing points (including clamps, support & jointing bolts) size of busbar 12" x 1/2"/14" x 1/2" or 10" x 1" of red, yellow & blue phase busbar. Cleaning of all joints & contact surfaces p

Installation/testing & commissioning of different type of lighting luminaries & its repair wherever needed- 125W HPMV lighting fittings.

Installation/testing & commissioning of different type of lighting luminaries & its repair wherever needed.- 250W HPMV/150W SV lighting fittings.

Installation/testing & commissioning of different type of lighting luminaries & its repair wherever needed- 400W HPMV/250W SV lighting fittings.

Fixing of the new/old copper fllexible jumpers with both end lugs to the mounting block and busbar with nuts & bolts (before fixing the jumpers the contact surfaces of the lugs should be clleaned properly as per instruction).

Termination of 11KV XLPE/PILC cable by M.Seal termination kit/heat shrink type and straight through jointing (M.Seal type). The termination/striahgt through jointing kit shall be supplied by the Contractor. Size 3C x 150 to x 300 Sq.mm.

LIGHTING/POWER POINTS/ELECTRICAL INSTALLATION.Installation/testing & commissioning of the following lighting luminaries or replacement of defective component and repair of existing luminaries and its recommissioning.1000W Halogen fitting

Termination of 11KV XLPE/PILC cable by M.Seal termination kit/heat shrink type & straight through jointing (M.Seal kit).The termination/straight through joint kit to be supplied by the Contractor.Termination of 11KV cable 3Cx120-185 Sq.mm.

Digging of cable trench & its refitting by excavated soil, sand & bricks after laying the cables. Size of trench 300mm x 950mm depth.

Laying/Re-routing of 1.1KV grade PVC armoured cable of following sizes:- 3.1/2C x 150 Sq.mm to 300 Sq.mm .

Termination of 1.1KV grade cable through suitable glands & lugs The glands & lugs shall be supplied by the Contractor. 3.1/2C x 150 Sq.mm to 300 Sq.mm.

Dismantling of following sizes of cables from cable tray/under-ground & its reeling for further use. The size of the cables :- 1.1 KV grade PVC armoured, PVC inner & outer sheated AYFY type cable 3.1/2C x 30 Sq.mm to 3.1/2C x 300 Sq.mm.

Cutting of road & placing of GI/MS pipe for cable laying & after laying the cable, the road repairs as per previous condition.

Laying/Re-routing of 1.1KV grade PVC armoured cable of following sizes:- 4C x 16 Sq.mm to 70 Sq.mm

Supply and installation of GI strip Size 40mm x 6mm for earthing.

Laying/rerouting (if necessary) of 11KV PILC/XLPE cable of 3C x 120 -150 Sq.mm.

Dismantling of any damaged structure, platform, cable tray or column related to electrical equipment, including pipe line of A.C etc.

Fabrication, erection & fixing of the structure, platform, cable tray, column etc including pipe line jobs. Necessary steel shall be supplied by HCL/ICC and necessary painting is under the scope of Contractor.

Installation & commissioning of 4 SWG/2 SWG bare copper wire for cross line of EOT cranes with proper tightening on insulator or intermittent support the job includes dismantling of existing wires.

Installation, testing & commissioning of DB with 500 Amp. Incoumer & 200 Ampr./ 63 Ampr. outgoing feeders.

MOTOR DE DUSTING, CLEANING,CHECKING OF TERMINAL CONNECTIONS,GENERAL VISUAL INSPECTION OF FOUNDATION AND COUPLING AND CURRENT MEASUREMENT ON LOAD-UP TO 10 HP

MOTOR DE DUSTING, CLEANING,CHECKING OF TERMINAL CONNECTIONS,GENERAL VISUAL INSPECTION OF FOUNDATION AND COUPLING AND CURRENT MEASUREMENT ON LOAD-UP FROM 10 HP TO 50 HP

MOTOR DE DUSTING, CLEANING,CHECKING OF TERMINAL CONNECTIONS,GENERAL VISUAL INSPECTION OF FOUNDATION AND COUPLING AND CURRENT MEASUREMENT ON LOAD-UP FROM 50 HP TO 100 HP

MOTOR DE DUSTING, CLEANING,CHECKING OF TERMINAL CONNECTIONS,GENERAL VISUAL INSPECTION OF FOUNDATION AND COUPLING AND CURRENT MEASUREMENT ON LOAD-UP MORE THAN 100 HP

MAA CONSTRUCTION

ADITYA SALES CORPORATION