FURNISHING WORK FOR 100 BEDDED HOSPITAL AT PT. DEEN DAYAL UPADHYAY GOVT. CORONATION HOSPITAL, DEHRADUN

Amount

Medisol Netted Top Hospital Curtain size 4'x7' made of polyester. Curtain joint finished with two ways stitching rather then over lock

Telescopic height adjustable saline stand mounted on castor. Over all dimension should be 695 mm dia base circle with ht adj from 1568 mm to 2121 mm. The 4 pronge bottom frame should made of 1.6 mm thick mild steel and the lower basement should be 3 mm dia with 1.6 mm thick ms tube. Four nos.high endurance anti static plastic moulded 50 mm castors should be provided with dual locking. The telescopioc rod should be 19 mm dia , 1.6 mm thick ss 304 grade tube with locking knobe. 4 nos hooks are provided for hanging saline bags. The telescopic tube should have plastic bush at the bottom which provide smooth linear motion during ht adjustable. All the ms part are pretreated with 9tank process with zinc phosphate and powder coated with anti microbial epoxy polyester powder coating.

G - rail hospital curtain track with dust resistance PVC cover strip to be mounted on wall/ceiling.

Visitor Chair. The seat and back shall be made of 15mm thick hot pressed commercial plywood and injection moulded PP inner padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32kg/m³ in back. The same shall be upholstered with fabric tapestry 1mm thick and 300 GSM. Seat and back shall be arrested together with powder coated HR steel spine covered with PP bellow. The armrest shall be used one piece polypropylene arm completely joint with seat. The frame structure shall be cantilever support type made up of MS/CRCA powder coated round pipe of Dia 25.4mm with 2mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 440±10 mm(D) X 450±10 mm(W) and back size shall be 415±10 mm(W) X 510±10 mm(H) from seat. Overall height shall be = 915±10 mm, overall depth = 590±10 mm & overall width = 580±10 mm.

Slotted angle rack with an overall size 900mm (W) X 600mm (D) X 1800mm (H). The panel shall have 5 nos. of shelves made up of 0.8mm thick high yield strength CRCA sheet of grade ‘D’ confirming to IS: 513. CRCA slotted angle shall be supplied with 2mm thick having size 40mm X 40mm. All steel components shall be 40-60µ thick (DFT) powder coated after 7 tank pre-treatment process flow. Corner plate (gussets) and fasteners shall be provided for complete assembly. Load capacity per layer 50-100 kg.

(L)1965*(W)830*(H)100 The bed should be provided with 40 density 100 mm thick PU foam mattress which should be covered by heavy helium material which is water proof, flame retardant, vapour & X-ray permeable. The zip & stiches for the mattress cover should be concealed.

Overall Dimension: Overall Sizes Diagonal Leg Dia 538 mm H470 min-655max Top plate should made of SS 202 made sheet with spin section of thickness 1mm & should be non corrosive. It should have a diameter of 305mm, seat base should made of MS ring and rectangular tube. EN8 Screw having dia of 22 mm should be used for height adjustment of the seat base. The round hub should be made of MS ERW tube having dia of 38mm and thickness 2 mm. The Hub should be welded with the legs and it should accommodate and cover the lead screw mechanism. The understructure should consist of 4 legs made up of MS ERW tube of diameter 25.4 mm and 1.6mm thick. The press formed pipe leg should give a round & clean look. All the legs should be provided with 4 nos of Nylon-6 bush. All metal components should be pre treated with zinc phosphating in 9 tank porcess and then powder coated with anti microbial epoxy polyster powder coating to fulfill the requirements for bacterial protection against at least 2 commonly found bacteria in Hospital environment [Gram positive and Gram Negative]. Safe working load must be 135kg

Revolving chair. The seat shall be made of 15mm thick hot pressed plywood upholstered with high resilience polyurethane foam (25+19)mm thick having density 40 kg/m³ with foam net tapestry 0.9mm thick and 300 GSM and the back shall be made of 15mm thick plywood on edges with metal frame upholstered with high resilience polyurethane foam 12mm thick having density 23kg/m³ with breathable mesh tapestry. The seat and back shall be arrested together with pipe frame and the armrest shall be used polyurethane arm mounted on pipe frame completely joint with back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged MS/CRCA powder coated having pitch circle dia. 650. mm fitted with 5 nos. twin wheel castors which shall be made of injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA standard X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 465±10 mm(W) X 475±10 mm(D) and back size shall be 440±10 mm(W) X 465±10 mm(H) from seat. Overall height shall be = 900±10 mm, base width/depth = 710±10 mm.

Overall dimension should be 625 mm dia and 955 mm height. The base frame should be made of 25 mm dia and 10 mm dia 1.6 mm thick ERW tube.It should be fitted on 50 mm dia castor. The bag should made of Casement fabric which should be wasable. Overall load bearing capacity should be 10 kg. packing goods should be supplied in knocked down construction to reduce carbon emission. The manufacturer should compilant with ISO 9001:2015,ISO 14001:2015,ISO 13485:2016, OHSAS 18001:2007 and CE certification.

Stretcher Trolley, Overall Dimension - 2160mm Lx 560 mm W, Removable stretcher top. Four 150mm wheel two with lock. Complete stainless steel construction. All steel components shall be 40-60µ thick (DFT) powder coated after 7 tank pre-treatment process flow

Instrument Trolley, Overall size 760 mm L X455 mm WX 810 mm height. Made up of SS 304 Grade. It have two shelf made of 18 G SS 304 sheet with downward bending. Frame is made up of 25 mm round pipe of 18 G SS 304 .Railing on three side on both shelf of 10 mm dia. rod of SS 304. All steel components shall be 40-60μ thick (DFT) powder coated after 7 tank pretreatment process flow.4 Nos. of Non-rusting Castor wheel of 125 mm Dia. (two with lock and two without lock.).

overall dimension: - 902(L) X 532(B) X 915(H) mm. Top shelf & bottom shelf should be made of SS304 sheet with 1mm thickness & 1.2mm. Rest of the components like supporting legs, horizontal bar handle should be made of SS 304 pipe having dia 31.8, 12.7 mm respectively. The castors of high quality plastic injected molded & anti static having the dia of 125mm should be used.Handles made of SS 304 pipe having section of 16mm & thickness of 1.2mm should be used.

SS 304 sheet should be used at top for the placement of the instruments being used & also for easy portability.SS 304 sheet should be at the top as well as bottom shelf for keeping the instrument being used. Horizontal bars should be welded with legs to provide protection at sides with supporting legs for sturdy structure. Castors of 125mm Dia. should be used for easy in movement. Spin section should be provided to the bowl giving a aesthetic look & also bucket should be provided with removable lid & a handle to lift the bucket. Overall Dimension must be 1156 mm X 531mm X 915mm H. The TOp and bottom shelf should be 1 mm thick ss 304 sheet, the shelf size is 755 mm x 467 mm. The supporting legs should be 31.08 mm dia 1.2 thick ss 304 tube. The horizontal bar should be 12.7 mm dia 1.2 mm thick ss 304 tube. to support top & bottom shelf. Maximum safe working load must be 40kg. the shelf should have 10 kg load and bowl & bucket should have capacity of 5 kg load.

Table size shall be 1200 Width mm x 600 Depth mm x 750 Height mm . The table top shall be made of pre- laminated particle board with 18 mm thick and 15 mm thick understructure covered with PVC lipping .There shall be locking provided for top drawers only , attractive black colour handles for all drawers plus only one colour is available beech. It shall have only 1 drawer attachment .

Dimension Overall dimension: (L) 2222 mm x (W) 922 x (H) 610mm Functions One function bed with adjustable backrest 70deg Head board & foot board ERW round tubes of thickness 1.2mm must be made with section 19, 25.4 & 31.7mm Bed frame ERW round & rectangular tubes should be used with thickness of 1.6 mm. Sleek base frame with large clear space & improved ground clearance with long base structure provides greater stability. Lying surface frame ERW round tubes should be used with thickness of 1.6mm with section 25.4 mm Lying surface Lying surface must be made of CRCA sheet with thickness of 1mm & must be powder coated with anti microbial & anti rust coating. It should consists of mattress retainer to define the mattress position. mechanism All functions should be operated with lead screw mechanism, ACME threaded EN8 made 6mm pitch for easy in movment Castors High endurance, plastic injection molded castors of 125mm dia having provision for diagonal locking with stem dia 22mm to be provided for better stability Powder coating Anti rust, thermosetting epoxy polyester powder coating must be used. All powder coating must be in Ral White. Certifications The manufacturer should compilant with ISO 9001, 14001, OHSAS 1800, ISO 13485 and CE certification. Maximum weight Maximum safe working load must be 135 kg. Handle PPCO made snap locking foldable handle place at 90deg minimizes the pressure on the wrist & makes it easily operational. Provision for mounting mosquito net pole and IV poles are provided. The manufacturer should compilant with ISO 9001, 14001, OHSAS 1800, ISO 13485 and CE certification.

overall dimensions should be 400W x 400 Dx 835mm H.The Locker should have one cabinet unit fitted with Cam lock. The legs are fitted with plastic leg bushes.The locker top should be of 0.8mm thick SS 304 Grade sheet . The SS sheet should be finished in buff-matt finish The top should have raised border of 10mm hieght on three sides.Cabinet should made 1 mm thick CRCA sheet . It should be fitted with hinge door and lock. The dooor should have louvers for ventilation. It should be provided with recess to serve as handle. Back of the locker should be provided with vertical spacer made of nylon.it should have uniformaly distributed total load bearing capacity of 20 kg.To ensure qood quality welding " Co2 Argon" process should be adhered to. All metal components should be pre treated with zinc phosphating in 9 tank porcess and then powder coated with anti microbial epoxy polyster powder coating.goods should be supplied in knocked down construction to reduce carbon emission. proof loading test , cycle tests , impact test, horizontal & vertical load tests for side rails, salt spray test, castor break test, pull test for head and foot board.

Overall dimension 1975 mm (L) x 560 mm ( W) x 805 mm (H). Examination couch with three drawers with three cabinets, inbuilt step stool and BP tray holder.the base frame should made of 30 mm x 30 mmX 1.6 thick ERW tube. The cabinets should made of 1 mm thick CRCA sheet with recessed plastic handles and with lock and plastic door latch. the hindges of the cabinet should be made of sheet metal and pin arrangement. The internal dimension of the two side cabinets should be 422 mm (W) x 455 mm (D) x 540 mm (H). the internal dimension of the centarl cabinet should be 422 mm (W) x 455 mm (D) x 358 mm (H). The storage cabinet unit should be mount tubular base frame. The head rest should be adjustable on gas spring which should be actuated with C shaped handle lever . The drawers should made of 1 mm thick CRCA sheet with recessed plastic handles and work on double extension ball slides for smooth glide. the internal dimension of the drawer should be 330 mm (W) x 427 mm (D) x 92 mm (H) The mattress platform should be 65 mm thick which is made of 12 mm thick ply and PU foam and covered with leatherite cover.the cover should be water resistant, fire retuardant, aniti micraobial . the cover should have in-vitro cytotoxicity test report from reputed test lab. the end of the top mattress surface should be tapered end edge for ergonomic benifit. There should be ss304 made tissue roll holder present on the lower side of the back rest. There should be 1 mm thick CRCA made step stool with leveler with double extension ball slide for smooth operation. There should be 1 mm thick CRCA made BP aparatus holder which should be adjustable in height on a SS made height adjustable rod. Total load bearing capacity should be 135 kg. The examination couch should be provided with six numbers levelers made of metal & plastic for adjustment on the uneven floor. All the metal parts should be pre treated and powder coated with epoxy polyester powder coating. The examination couch should have CE certification from any notifying agency or its Indian counterpart, the manuafacturer shoudl have ISO 13485:2016 certfication from any notifying agency.

SEAT/BACK FRAME ASSEMBLY: The seat and back should be made of 0.1 ±0.012 cm thick CR steel perforated sheets which should be welded to a seat/back frame assembly made of 0 1.9 ±0.02cm x 0.16 ±0.0128 cm thk MS ERW tube. Connecting Strips made of 0.5cm thick HR steel should be welded to the structure. The mounting base subassembly made up of 0 1.9 ±0.02cm x 0.16 ±0.0128 cm thk & C-channel made of, 0.315±0.022cm HR steel welded to connecting strip for assembly with the connecting beam. SEAT. SIZE: 39.2cm. (W) x 41.5cm.(D) (Approx.) BACK SIZE:39.5cm. (W) x 21.5cm.(H) (Approx.) CONNECTING BEAM ASSEMBLY: It should be made up of 5.0 ±0.03 cm x 5.0 ±0.03 cm x 0.16 ±0.0128 cm thk. M.S.E.R.W Squshould be tube. The connecting beam should be powder coated ( DFT 40-60 microns ). The ends of the Beam should be closed with L-shaped plastic end cap made from PP material. The connecting beam assembly should be powder coated (DFT 40-60 microns). LEG ASSEMBLY: It should be made up of 5.0 ±0.03 cm x 5.0 ±0.03 cm x0.16 ±0.0128 cm thk. M.S.E.R.W Squshould be tube. and 0 3.175 ±0.03 cm x 0.2 ±0.016 cm thk M.S.E.R.W tube welded together to C-channel made of 0.2 ±0.018 cm thk CR steel. Plastic End caps should be fitted to Legs. The leg assembly should be powder coated ( DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 44.5 cm. Height - 77.5 cm. Width & Depth of Chair as - Width-160.0cm and Depth-57.5 cm.

White madical storage unit with customized size made of stainless steel as shown in figure.

Glass Door Storwel shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded construction. It should have shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The glass door storwel shall have a brass handle and a 2 way locking mechanism with shooting bolt . It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Table S - 1071 size shall be 1800 Width mm x 900 Depth mm x 725 Height mm.The Top shall be 25 mm thick pre-laminated board with 2 mm thick matching lipping stiffener provided under the top to give addition strength(1.6 mm thick MS).The Understructure shall be having pedestal of combination of processed wood (PLB) and mild steel (MS).There shall be 2 box drawers plus 1 filling drawer combination for both pedestals the pedestal shell shall be 0.8 mm thick MS plus the drawer tray and separator shall be 0.6 mm thick MS.There shall be sleek handles for easy grip , glide screws for leveling and also independent locking arrangement for each pedestal. The Modesty shall be of MS panel (1.0 mm thick) recessed inside for more leg room.Panel is styled with cutouts (windows) to give it a trendy and up market look.

Overall dimensions: (L)2241 mm X ( W)1050 mm X (H) 561mmm until bed frame from the floor with mattress complete. 2 function Motorized operated bed Back rest and Knee rest and lower knee rest. Back rest angular movement: 65 deg; Knee rest angular movement: 30 deg to be operated through control panel Safe working load should be 200 kgs Patient load bearing capacity: 135 kgs. All edges in contact with patient to be rounded safely. Head & Foot board should be made of blow molded Poly propylene with bacteriostatic additives . Head board and foot board should be with metal inserts to mount it on bed frame. Removable PP head board and foot board should have cut out , for better gripping. Bed frame should be made of MS ERW tube of size 50mmx25mm of 2 mm thick supported with ERW square tube with 25 mm x 25 mm and 1.2 mm thick. All corners of bed frame are provided with bumper mounting holders and it should have provision 4 iv pole holders Base frame should be made of MS ERW tube of size 30mmx60mm of 2mm thick. Base frame should have ground clearance of greater than 150 mm to avoid any obstruction during bed movement. Base frame should have provison to mount oxygen cylinder cage. It should have trendelenburg indicator guide Bed lying surface should be made of PP injection mould . This lying surface should have sections for bed profiling i.e. back adjustment, fixed pelvic section, upper and lower leg adjustment.Lower leg rest section is provided with Ratchet for leg rest adjustment with a single hand operation to acheive the position. Mattress platform is strengthned by frame of size 25 mm x 25 mm and 1.2 mm thick. 4 Neoprene rotating bumpers of dia 92mm height 69mm with 40-50 shore hardness are provided at four corners to protect the bed and patient from impact and avoid damages to wall The bed should be provided with 125mm wheel dia,twin wheel ,plastic polymer with metal insert castors. Out of 4 castors two should be provided with brake, mounted at diagonally opposite position The bed should be provided with PP molded side boards of 4 no's providing full coverage to bed. These side boards should be with bacteriostatic additives. These side boards should be integrated with drop down mechanism for easy operation. The side boards should be provoded with angle indicators. The bed should have MS powder coated urine bag holder on both side of the bed for ease of accessibility To ensure qood quality welding " Co2 Argon" process should be adhered to. All metal components should be pre treated with zinc phosphating in 7 tank porcess and then powder coated with bacteriostatic epoxy polyster powder coating to fulfill the requirements for bacterial protection against at least 2 commonly found bacteria in Hospital environment [Gram positive and Gram Negative]. proof loading test , cycle tests , impact test, horizontal & vertical load tests for side rails, salt spray test, castor break test, pull test for head and foot board. The manufacturer should be compliant with the following standards: IEC 60601-1 Medical Electrical Equipment: General requirements for safety and essential performance. IEC 60601-2-52 Medical Electrical Equipment: Particular requirements for safety and essential performance of medical beds. IEC 60601-1-4 General Requirements for Safety: Programmable electrical medical systems. ISO 14971 Medical Devices: Application of risk management to medical devices. ISO 13485:2016 Medical Devices: Quality Management Systems - Requirements for regulatory purposes. CE Certificate from European cerrtifying agency with 4 digit registration code, The bed should be provided with Telescopic IV pole made of Stainless steel to mount saline bags. IEC 60601-2-52 Medical Electrical Equipment: Particular requirements for safety and essential performance of medical beds. IEC 60601-1-4 General Requirements for Safety: Programmable electrical medical systems. ISO 14971 Medical Devices: Application of risk management to medical devices. ISO 13485:2016 Medical Devices:

Scrub Sink.Overall Dimensions: Length: 925 mm Width:475 mm Height:250 mm. Bowl Dimensions: Length:250 mm Width:350 mm Depth:250 mm.The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40-50μ thick. material S.S. 304 grade.

Godrej and boyce mfg co ltd