Vadodara Division: Provision of Passenger Escalators at 12.0-meter-wide FOB (including civil engineering works) at Bharuch Railway Station in connection with Amrit Station works.

A- S/I/T/C of Passenger Escalators

B- Electrical Power Supply Works

C- LED Fittings

D-Allied Civil Engineering works

Item Breakup - A- S/I/T/C of Passenger Escalators

Design, manufacturing, supply, erection, testing and commissioning of Passenger Numbers Escalators as per RDSO's specification No. RDSO/PE/SPEC/TL/0095 (Rev.'4'), 2026 with latest amendments, all accessories and safety devices - 1. Design, manufacture, supply installation, testing and commissioning of passenger escalators as per RDSO's Specification No. RDSO/PE/SPEC/TL/0095 (Rev '4') - 2026 with latest amendment with all accessories and safety devices at Bharuch railway station as per annexure attached. 2. The standard vertical height of escalator is 6.0 meter. The supplier shall be given +/- 0.6% quoted rate with variation of vertical height +/- 0.15 meter. Therefore, if the height becomes 6.15 meter, then the amount paid to bidder will be 1.006 times quoted rate and if height becomes 5.85 meter, then amount paid will be 0.994 times quoted rate. 3. Escalator shall be of State-of-the-art technology, having nominal step width of 1000 mm, with four Nos horizontal steps on top and bottom landing area and the nominal speed will be 0.5 m/sec. 4. Maximum carrying capacity will be 100 passengers per minute, angle of inclination of escalator shall be 30°. 5. The escalator shall be complete with all parts and accessories, which are necessary for its efficient operation, whether specifically mentioned or not, public announcement system. 6. A CCTV system with at least two cameras, microprocessor-based monitoring and fault diagnostic system, and all safety features and shall fully comply with International Standard EN-115, IS4591 latest version. 7. Warrantee - Twenty-Four (24) months with comprehensive maintenance and failure attendance. 8. Detailed scope of work is based on RDSO's Specification No. RDSO/PE/SPEC/TL/0095 (Rev.'4'), 2026 which is attached as enclosure. Total 24034900.00

Item Breakup - B- Electrical Power Supply Works

The price shall cover for wiring of two wire sub-main with 2.5 sq. mm PVC insulated, Metre unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 with one wire of 1.5 sq. mm PVC insulated, unsheathed, multi- stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 in medium grade PVC casing capping of not less than 25 mm size, double lock type, ISI marked of make Prestoplast/Precision/Modi/Gerard or medium grade PVC conduit of not less than 19 mm diameter, ISI marked of make Prestoplast/Precision/Modi/Gerard as per site conditions. Total 19800.00 Item- 2 Wiring of sub-main with copper wire, single core 2.5 sq. mm in existing casing-capping/conduit S No. Item No Description of Item Unit Qty Rate Amount

The price shall cover for wiring of two wire sub-main with 2.5 sq. mm PVC insulated, Metre unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 with one wire of 1.5 sq. mm PVC insulated, unsheathed, multi- stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 in existing PVC casing-capping or medium grade PVC conduit of not less than 19 mm diameter, ISI marked of make Prestoplast/Precision/Modi/Gerard as per site conditions. Total 15912.00 Item- 3 Wiring of sub-main with copper wire single-core 4.0 sq. mm in casing-capping/conduit S No. Item No Description of Item Unit Qty Rate Amount

The price shall cover for wiring of two wire sub-main with 4.0 sq. mm PVC insulated, Metre unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 with one wire of 2.5 sq. mm PVC insulated, unsheathed, multi- stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 in medium grade PVC casing capping of not less than 25 mm size, double lock type, ISI marked of make Prestoplast/Precision/Modi/Gerard or medium grade PVC conduit of not less than 19 mm diameter, ISI marked of make Prestoplast/Precision/Modi/Gerard as per site conditions. Total 12480.00 Item- 4 Wiring of sub-main with copper wire, single core 4.0 sq. mm in existing casing-capping/ conduit S No. Item No Description of Item Unit Qty Rate Amount

The price shall cover for wiring of two wire sub-main with 4.0 sq. mm PVC insulated, Metre unsheathed, multi-stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 with one wire of 2.5 sq. mm PVC insulated, unsheathed, multi- stranded, FRLS copper conductor of 1100 Volt grade, ISI marked, conforming to IS: 694/1990 in existing PVC casing-capping or medium grade PVC conduit of not less than 19 mm diameter, ISI marked of make Prestoplast/Precision/Modi/Gerard as per site conditions. Total 9800.00 Item- 5 Providing Exhaust Fan, 380/400 mm sweep, industrial heavy duty with louver/bird guard S No. Item No Description of Item Unit Qty Rate Amount

The price shall cover for supply of heavy duty, industrial Exhaust Fan of metal body, Numbers 380/400 mm sweep with bird guard operating on 230 Volt, 50 Hz AC supply complete with all accessories of make Crompton Greaves/GEC/Almonard/Usha/Bajaj. The price shall also cover for fixing, testing and commissioning of the Exhaust Fan on existing pocket with rake bolts/Anchor fasteners of suitable size as per site condition, and its connection from existing ceiling rose with three-core, 24/0.20 mm size, FRPVC insulated, flexible copper wire of 1100 Volt grade. Total 4100.00 Item- 6 Supply, installation, testing and commissioning of MCCB, four-pole, 63 Amp with outdoor type MS enclosure S No. Item No Description of Item Unit Qty Rate Amount

The price shall cover for supply, installation, testing and commissioning of MCCB, four- Numbers pole, 63 Amp, with thermal-magnetic release range 50 to 63 Amp, Ics = 100% Icu having 35 KA breaking capacity and conforming to IS/IEC 60947-2 with adjustable overload and short circuit settings and inbuilt instantaneous protection of ABB/L&T/HPL/GE/MDS/Siemens/BCH/C&S/Schneider/CGL/Havells make. The MCCB shall be supplied with spreader terminals and rotary handle in sheet steel modular enclosure or pre-fabricated double-door enclosure of same make as the MCCB as far as possible. The enclosure should be suitable for outdoor installation conforming to IP: 65 protection. Total 27468.00 Providing floor mounted, outdoor type Distribution Board with incomer MCCB, four-pole, 250 Amp - 1 No and outgoing MCCB, four-pole, 125 Amp - 3 Nos, Item- 7 MCCB, four-pole, 100 Amp - 3 Nos and MCCB, four-pole, 63 Amp - 3 Nos with multifunction energy meter, indication lamp etc S No. Item No Description of Item Unit Qty Rate Amount

The price shall cover for design, supply, installation, testing and commissioning L.T. Numbers Distribution Panel fabricated from 2.0 mm thick M.S. sheet, standard angles, channels etc. as required in design. The drawing, design, switch gears with make and model of the LT panel shall be submitted by the contractor in three copies and got approved from site engineer before fabrication. The LT panel shall be indoor/outdoor, rectangular cubicle type, dust and vermin proof suitable for three-phase, four-wire, 415 Volt, 50 Hz AC supply system. Details are given in Annexure-XXI of tender document. Total 127215.00 VADODARA DIVISION-ELECTRICAL/WESTERN RLY Digging of cable trench 100 mm wide and 200 mm deep in concrete/tar road/platform and refilling to its original position after laying of cable in 50 mm Item- 8 diameter HDPE pipe S No. Item No Description of Item Unit Qty Rate Amount

The price shall cover for digging of cable trench of size 100 x 200 mm deep in concrete/tar Metre road/platform surface and its refilling/plastering after laying of cable in 50 mm diameter HDPE pipe of Tijaria/Himalyan/Koncept/Poddar/ Unique/Dutron/Reliance/Baba/Shivam make in existing trench. Supply and laying of HDPE pipe, 50 mm diameter is included in the scope of work. Total 149600.00 Item- 9 Supply and erection of G.I. perforated cable tray of size 200 mm x 100 mm x 100 mm on MS frame with cover S No. Item No Description of Item Unit Qty Rate Amount

The price shall cover for fabrication, supply and fixing of M.S. perforated cable tray, hot dip Metre galvanized as per latest ISS/BSS of size 200 x 100 x 100 mm and 2.0 mm approximate thickness with appropriate cover of thickness 1.6 mm. The cable tray shall be fixed horizontally or vertically at site and the existing LT cables shall be laid/shifted in the cable tray by disconnecting from the panel/switch end and reconnecting as per site requirement duly tied with suitable clamps with GI nuts, bolts and washers in a safe and secure manner. The fixing clamps shall be fabricated from 50 x 50 x 6 mm MS angle or 50 x 6 mm MS flat duly painted and fixed at approximate distance of 1.5 to 2.0 meter apart with 2" long dowel/fisher rack bolts. The tray shall be fabricated in lengths of 2.0 m and couplers shall be provided at joints. The cable tray cover shall be fixed with GI screws. Total 323760.00 Item- 10 Providing PVC maxi trunking of size 100 x 50 mm S No. Item No Description of Item Unit Qty Rate Amount

The price shall cover for supply, fixing, testing and commissioning of ISI marked PVC Maxi Metre Trunking of size 100 x 50 mm with all accessories of PRECISION/GERARD/MODI/PRESTOPLAST/PRESS FIT make. The PVC Maxi trunking shall be fixed at site by fabricated clamp of 18 SWG GI sheet at a distance not more than 1.5 meters by machine screw/GI nut bolts, washers etc. The existing power cables shall be laid in the PVC Maxi trunking properly dressed and secured by means of suitable clamps/fasteners etc. Total 45100.00 Item- 11 Laying of cable in trench S No. Item No Description of Item Unit Qty Rate Amount

The price shall cover for laying, testing and commissioning of LTUG armoured cable in Metre existing trench/pipe and its connection at both ends. The cable shall be tested with 500 Volt Megger earth tester before laying it in the trench. The cable cores shall be tested for continuity, absence of cross phasing, Insulation Resistance between conductors to earth/armour and between conductors. The results should be recorded in presence of railways' representative. A composite cable layout plan on ferro-print or computerized print duly laminated in A-4 size should be submitted by the contractor to this office as well as site in-charge after laying of cable. Cables shall be supplied by railways at site engineer's stores. Total 10500.00 Item- 12 Laying of cable on wall/cover shed/existing tray with MS clamp S No. Item No Description of Item Unit Qty Rate Amount

The price shall cover for laying, testing and commissioning of LTUG armoured cable on Metre wall/cover shed/in existing tray and its connection at both ends. The cable shall be tested with 500 Volt Megger before laying it in the tray. The cable cores shall be tested for continuity, absence of cross phasing, Insulation Resistance between conductors to earth/armour and between conductors. The results should be recorded in presence of railways' representative. A composite cable layout plan on ferro-print or computerized print duly laminated in A-4 size should be submitted by the contractor to site engineer and Divisional Office after laying of cable. Total 37700.00 Design, manufacture, display and installation of wall/hanging/floor mounting type LED illuminated signage/directional boards in flat/half elliptical/parabolic/triangular shape. The display sheet shall be of unbreakable 040 translucent polycarbonate sheet of 2.0 mm thickness. The text/graphics Item- 13 matter visibility shall not be less than 160 deg. The approved colour text and graphics shall be printed/router cut on monomeric calendared vinyl of 70 um thickness and shall be firmly pasted on display sheets S No. Item No Description of Item Unit Qty Rate Amount

Design, manufacture, display, installation of wall/hanging/floor mounting type Square Foot signage/directional boards in flat/half elliptical/ Parabolic/Triangular shape. The display sheet shall be of unbreakable 040 translucent polycarbonate sheet of 2.0 mm thickness. The text/graphics matter visibility shall not be less than 160 deg. The approved colour text and graphics shall be printed/ router cut on monomeric calendared vinyl of 70 um thickness and shall be firmly pasted on display sheets/Retro Reflective Boards. The mounting arrangement shall be hanging, wall mounting, ceiling mounting, pole mounting or floor mounting and as per site requirement to be provided by the contractor with their own materials, labour, all Tools & Plants, lead, lift, transportation etc including all applicable taxes. The signage shall have the integral mounting arrangements with sturdy structural frame and ACP cladding on the back side of the signage to avoid rusting and entry of dust. The scope of work covers Bharuch station of Vadodara Division. 1.0The work shall be carried out as per the "Guidelines on Standard Signages at Stations on Indian Railways, 2023" issued by the Ministry of Railways, Government of India. The work shall be executed strictly as per the specifications given in the document which is attached as Annexure. Colour scheme, font sizes, directional arrows, materials, fabrication, text, pictogram shall be as given in the document. Total 142080.00 Item- 14 Providing GI earthing strip, 25 x 4 mm with PVC sleeve S No. Item No Description of Item Unit Qty Rate Amount

The price shall cover for supply and laying of G.I. earthing strip of 25 x 4 mm size covered Metre with black coloured PVC sleeve of super quality from earth pit to control/distribution panel board. The earthing strip when laid on wall, shall be fixed by means of suitable size of GI clamps and screws. Total 12000.00 Item- 15 Providing maintenance free earthing S No. Item No Description of Item Unit Qty Rate Amount VADODARA DIVISION-ELECTRICAL/WESTERN RLY

The price shall cover for providing maintenance free earthing as per the following Numbers specifications - 1. High tensile-low carbon steel rod having diameter not less than 17 mm complying with requirements of BS 4360 Grade 43A or EN10025:2-004 S275JR, molecularly bonded by 99.99% pure high conductivity copper on outer surface with copper coating thickness of 250 micron or more, Length 3000 mm (minimum). Certificates from NABL approved labs shall be submitted with test results. 2. Copper earth bus-bar of size 250 mm x 50 mm x 6 mm having electrical conductivity of 101% IACS, minimum 99.9% copper content shall be exothermically welded to rod with 4 holes of 12 mm diameter (two on each side) for connecting earthing conductor. 3. Earth Enhancement compound should have characteristics as mentioned in the RDSO specifications. It should have low resistivity preferably below 0.2 Ohm-meter, supplied in sealed bags (minimum 75 kg per pit for 5' x 5' x 10' size pit and minimum 50 kg per pit for 300 mm bore type pit. The bags shall be marked with manufacturer's name or trade name, quality, Batch No. and date of manufacture. Certificates from NABL approved labs shall be submitted with test results, for at least following parameters - i) Composition of Earth Enhancement compound ii) Resistivity - < 2 Ohm-meter iii) pH value - > 7 but < 9 iv) Moisture retaining capacity - > 10% at 105 degrees Celsius v) Water solubility - < 5% 4. Backfill material - Good quality soil or excavated soil free from sand, gravel and stones shall be used for backfilling. 5. Earth pit of size 5 feet x 5 feet x 10 feet or min 300 mm bore up to 10 feet using earth auger shall be made. 6. Inspection chamber - A concrete box of 300 x 300 x 300 mm (inside dimensions) and 50 mm thickness of wall, with smooth cement plaster finish shall be provided on the top of the pit. A concrete lid, painted black, approximately 50 mm thick with pulling hooks shall be provided to cover the earth pit. PVC sleeve shall be provided in concrete wall to take out earthing connections. 7. On backside of the cover, date of the testing and average resistance value shall be written with yellow paint on black background. 8. Instead of copper bus-bar and strips mentioned in the drawing, a GI main bus-bar of minimum size 300 mm x 75 mm x 8 mm to be installed on nearby wall etc. It shall be connected to earthing with two GI strips of 50 mm x 6 mm size each, up to a distance of 10 meters from earth bus-bar (minimum 3 meters x 2 Nos GI strips to be supplied). 9. Earthing shall generally be carried out in accordance with the requirement of I.E. Rules, 1956, as amended from time to time and shall confirm to IS: 3043 of 1987 with latest amendment. 10. The earth value shall be measured and recorded at the site by painting on earth pit or nearest wall along with date of testing. It shall be less than 2 Ohms and neutral to earth voltage shall be less than 3 Volt. 11. Earthing performance after a year of installation shall be jointly checked and measured. It should be less than 2 Ohm. 12. General arrangement of the earth system shall be as per the drawing given in Annexure-XXI of tender document. Total 165808.00

Item Breakup - C- LED Fittings

The price shall cover for supply, fixing, testing and commissioning of 15/18-Watt LED Numbers luminary operating on 230 Volt, 50 Hz AC supply as per Western Railways' specification no. WR/CCG/Specification/P/001 (Rev. 01) - 2018. The fitting shall be of pressure die cast aluminum suitable for surface/recessed mounting with high efficiency Polycarbonate diffuser. Luminous flux - 2000 lumen, rated luminous efficacy - 110 lumen/Watt, CCT - 6500 deg K, Colour rendering index (CRI) - 80, SDCM - < 5, iTHD - < 10%, Power Factor - 0.95, Median useful life L70B50 @ Ta - 45° C 50,000 burning hours, surge protection level - 2.5 kV with aluminum die cast housing. The fitting shall be fixed at site by means of suitable size of GI Clamps/PVC block as decided by site engineer. The connection shall be given by means of 24/0.2 mm three-core flexible copper wire through proper connector. The fitting arrangement shall be as per the aesthetics of the room. Removal of existing fittings and handing over the same to the site engineer at his store is included in the scope of work. Total 37454.00 Supply, installation, testing and commissioning of four-feet suspended linear light, IP-20 four-feet, with 50 mm width, housing constructed of extruded Item- 2 aluminum S No. Item No Description of Item Unit Qty Rate Amount

The price shall cover for supply, installation, testing and commissioning of four-feet Numbers suspended linear light with system lumen output of 2500 lumens @ 6500 deg K CCT and CRI - >80. The luminary shall be supplied with LED Driver with operating voltage range of 140 to 270 Volt AC, PF - >0.95, iTHD - <10% and 4 KV surge protection inbuilt inside the driver. The luminary should conform to Western Railways' Specification No. WR/CCG/ Specification/P/001 (Rev. 01) - 2018 or latest. The fitting shall be of reputed quality and make. The fitting shall be fixed at site by means of suitable size of GI Clamps/PVC block as decided by site engineer. The connection shall be given by means of 24/0.2 mm three-core flexible copper wire through proper connector as per site requirement. The fitting arrangement shall be as per the aesthetics of the room. Removal of existing fittings and handing over the same to the site engineer at his store is included in the scope of work. Total 309075.00

Item Breakup - D-Allied Civil Engineering works