Design Supply Installation Testing and Commissioning of Semi Automated Multi Level Car Parking system using Puzzle Parking Technology etc works at Medical College opposite to Super Specialty Block Thiruvananthapuram Corporation under AMRUT scheme

Amount

Laying and Jointing PVC Pipe. Heading

Civil Works -MLCP 2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.33.1 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.5 Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.2 Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.6 Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.3 Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

10.19 Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

10.1 Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

13.16.1 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

13.46.1 Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

51.2.3 Filling with Quarry Muck Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

16.89 Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi models location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

od962/2018_2019 Providing and laying profiled sheeting 970mm to 1000mm cover width, 26/28mm crest height at 195-200mm centers, made out of '0.5mm TCT, Cold Rolled steel of 550 Mpa yield strength conforming to ASTM A 368 or AS 1595 with hot dip metalic coating 'of minimum 150gm/Sqm zinc- aluminium alloy coating mass (55% Aluminium, 43.5% zinc and 1.5% Silicon ) total of both size as 'per ASTM A 792 or AS1397. The colour have shall have a total coating thickness iof 35microns of polyster paint system as per 'AS/NZS - 2728:1997 ( category 3 ) of approved colour, comprising of 20 microns exterior coat on top surface and 5 microns reverse 'coat on back surface over 5 microns primer coat on both surfaces. Roofing sheet shall be factory cut and required length of '(up to 12mtr ) to suite site conditions and design drawings. Roofing sheet shall be crest fixed to purlines with hot dip 'galvanized self drilling fastners with integral EPDM washers (one fastner on each crest) also, fastners to be provided on side laps. 'Minimum sheet overlap at end laps shall be 150mm. Penetration and end laps in sheet shall be sealed by using proper sealant. 'Profiled HDPE fillers shall be provided wherever required to close voids between capings and troughs of the sheet to provide a 'weather tight exterior. Rate shall include cost and conveyence of all materials, lead, lift, scaffolding, all labour charges, making the roof water tight with required sealent etc. complete at all level and as directed by Engineer-in-Charge.

od964/2018_2019 Providing and fixing ridge/ valley capping/flashing in required width (minimum 500 mm) with plain galvalume colour coated sheet made out of 0.5mm TCT, minimum 550 MPa cold rolled steel with hot dip metallic coating of Aluminium Zinc alloy (Galvalume) 150 gms/sqm,total of both sides, AZ 150 as per ASTM A 792 or AS1397, with polyester colour coating including cost and conveyance of all materials, scaffolding, lead,lift, labour charges, all taxes etc. complete at all levels as directed by Engineer-in- Charge

12.7.2 Providing and fixing 15cm wide, 45 cm overall semi circular plain G.S. sheet gutter with iron brackets 40x3 mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete.0.63 mm thick with zinc coating not less than 275 gm/ m2

2 MLCP Parking System od44829/2018_2019 Design, Manufacture, Supply, Installation, Erection, Testing And Commissioning of 3 units of Seven Level Six Grid (Type-A), 2 units of Seven Level Four Grid (Type-B) and 1 unit of Seven Level Eight Grid (Type- C) over-ground Puzzle Parking System with Electro Mechanical technology to accommodate minimum of 36 Cars Per Type -A unit, 22 Cars per Type-B and 50 Car per Type-C unit and in total minimum 202 car spaces with car Carrying Capacity of 2000 kg each in ground floor, & 1800 kg in 1st level to 5th level and Car Dimensions of 5000 mm length x 2100 mm height x width 2250mm (SUV) in ground floor, 5000 mm length x 1700 mm height x width 2250mm in 1st level to 7th level with average retrieval/parking time not more than 180 seconds. The Lifting speed should be @ 6 Meter/Minutes having Motor of 1.5 Kw for 1st floor, 3 Kw for 2nd & 3rd, 4 Kw for 5th & 6th and 5 Kw for 7th & above Floor pallets with lateral movement speed of 7 M/Min having Motor of 0.2 KW - 0.4 KW and having safety features as outlined in specifications and with all the structural frame work designed for all probable loading conditions including loads due to roofing/cladding, but excluding cost for truss and sheet for Roofing/cladding, Smart Card/RFID, Branding provisions, Mechanical barriers / Boom barriers, PLC with Auto as well as Manual Mode of operation including cost of maintenance for one year during the Defect Liability period as mentioned in tender documents inclusive all taxes

3.Electrical Work od157/2018_2019 Supply, Installation, Testing and Commissioning of outdoor 82.5 KVA prime rated D.G Set with acoustic enclosure and Control panel ,protection and digital metering,controls and interlocks, CTs and transducers for all metering and protection and suitable FP MCCB etc. , including antivibration mountings, exhaust silencer and exhaust pipe conforming to latest environment protection regulations for emission and noise levels complete with , water/ coolant cooled, (radiator type) four stroke, electric start conforming to BS: 5514 15 KVA prime rating, brushless, self excited, self regulated and suitable for continuous operation at 1500RPM, generating 415 V+/-5% Volts at 0.8 p.f (lag), 50Hz,3 phase, 4 wire system generally conforming to BS: 2613 & IS: 4722. Both Engine and Alternator shall be mounted on common channel iron base frame, and with standard accessories such as lead acid batteries and engine driven battery charger along with leads,battery stand, necessary control wiring with control cables, first fill of lubricating oil, and earthing as per standards Fuel tank , fuel piping from fuel tank to Engine, Residential silencer, suitable size Cable termination box with extended Alternator terminal with bus bars etc as required and as per specifications.Rate shall be inclusive of all the civil work including RCC foundation. The work should be as per Electrical Inspectorate/ Pollution control board standards.

od158/2018_2019 Supply, installation, testing and commissioning of energymeter box of cubicle construction made from 16SWG CRCA sheet suitable for accomodating one number of TOD meter with CT and 3 Nos of 160 A HRC fuse,160 A FP isolator and neutral link, interconnections, providing necessary supports made from the same gauge CRCA sheet to fix energymeters, etc.The cubicle shall be provided with hinged door construction and vision panel for the meter compartment. Suitable knock out for cable entry and exit shall be provided. The entire board shall be painted with 2 coats of synthetic enamel paint over a coat of zinc chromate primer etc as required including fixing it on wall, making good the damages colour washing etc. as required.

90.14.1.2 Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623.<br>Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.Supply and fabrication of MV panel board using 1.6mm CRCA sheet, powder coated (excluding base frame)

90.14.2.1 Supply and providing 2mm SMC sheet as shrouding for bus interconnection / terminations etc. including required nut & bolt etc.

90.14.3.2 Supply and providingOhetahvey rduty n'A'gsectionerneoprene gasket insathetipoannesl boardU' section rubber beeding suitable for 1.60/ 2.00 mm sheet

90.14.4 Supply and fabrication conveyance and installation of base frame of panel board using 75 x 40 mm rolled steel channel (ISMC)

90.14.5 Supply and fabrication conveyance and installation of angle iron frame work for wall mounting panel board

90.14.6 Supply and providing copper bus bars including finger type SMC bus bar supports in the bus chamber, suitable size nut & bolt, providng heat shrink sleeves etc. as required.

90.14.7 Supply and providing copper earth bus in the panel board

90.14.10.3 Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.16 A-100A, 16 kA (Ics=100%Icu), 4 pole, current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL

90.14.10.7 Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.160A, 35/36 kA (Ics=100%Icu), 3 pole, current limiting type MCCB with microprocessor based release with overload setting of 50 - 100% having adjustable OL & SC

od168/2018_2019 Supply and installation of ammeter inside panel board

od169/2018_2019 SUPPLY AND INSTALLATION OF (0-500V) VOLTMETER INSIDE PANEL BOARD

od170/2018_2019 Supply & Installation of LED type RYB (1 Set) Indication lamps inside panel board.

od171/2018_2019 Supply Intallation Testing and Comissioning of Four Pole Automatic Source Transfer Switch of 125 A rating with AMF Relay

90.14.28.6 S & F Motor starters of the following ratingsFully automatic star delta starter for 15HP motor

od172/2018_2019 Supplying and fixing DP 16/25/32 amps 230 volts "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

od173/2018_2019 Supplying and fixing SP 2-6 amps 230 volts "C" curve SP MCB complete with connections, testing and commissioning etc. as required.

2.3.1 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator6 way, Double door

2.14.1 Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residualcurrent circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

2.10.1 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

1.10.2 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVCinsulated copper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLSPVC insulated copper conductor single core cable etc as required.Group B

1.55.2 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group B

1.14.1 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.14.2 Wiring for circuit/ subPmain wirinRg alongwithIearth wCire with the Efollowing sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.21.1 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

90.12.1.34 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).3.5 core 185 sq mm

90.12.5.34 Supply & laying of one number PVC insulated and PVC 90.12.5.34 Supply & laying of one number PVC insulated and CPVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.3.5 core 185 sq mm

90.12.7.34 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 185 sq mm

90.12.1.32 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).3.5 core 120 sq mm

90.12.5.32 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.3.5 core 120 sq mm

90.12.7.32 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 120 sq mm

90.12.1.31 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).3.5 core 95 sq mm

90.12.5.31 Supply & laying of one number PVC insulated andPVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.3.5 core 95 sq mm

90.12.7.31 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 95 sq mm

90.12.1.14 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).3 core 10 sq mm

90.12.5.14 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.3 core 10 sq mm

90.12.7.14 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3 core 10 sq mm with factory made clamp

90.12.1.39 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).4 core 6 sq mm

90.12.5.39 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.4 core 6 sq mm

90.12.7.39 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 6 sq mm with factory made clamp

90.12.1.2 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).2 core 6 sq mm

90.12.5.2 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.2 core 6 sq mm

90.12.7.2 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.2 core 6 sq mm with factory made clamp

9.1.27 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm)

9.1.7 Supplying and making end termination withbrass compressiongland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 X 10 sq. mm (22mm)

9.1.24 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 95 sq. mm (45mm)

9.1.25 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 120 sq. mm (45mm)

od174/2018_2019 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 c 6 sqmm AL

od175/2018_2019 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 c 6 sqmm AL

5.2 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providingmasonry enclosure with cover plate having locking arrangement and watering pipe etc. withcharcoal/ coke and salt as required

od160/2018_2019 Providing and fixing GI/C u strip/wire on surfaceor in recess for connections etc. as required.

od161/2018_2019 Providing and fixing GI/Cu strip/wire on surface or in recess for connections etc. as required. 8 SWG GI WIRE

od162/2018_2019 Providing and fixing GI/Cu strip/wire on surface or in recess for connections etc. as required. 25 X 3 MM CU

od163/2018_2019 Providing and fixing GI/Cu strip/wire on surface or in recess for connections etc. as required. 25 X 6 MM GI

od165/2018_2019 Supplying and laying G.I/Copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) 8 SWG GI WIRE

od166/2018_2019 Supplying and laying G.I/Copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) 25 X 3 MM CU

od167/2018_2019 Supplying and laying G.I/Copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) 25 X 6 MM GI

4 Firefighting Works od156/2018_2019 Supply, installation, testing and commissioning of swaged street light pole of 5 meter height with 0.5 meter overhang single arm bracket suitable for mounting 1number 25W LED street Light fixtures. The pole shall be of 4.2M height made out of hot dip galvanised 3 mm thick MS sheet, primered and polyurethane painted suitable for mounting 25 W LED street light luminaire . The LED Street Lighting luminaire shall be of IP66 protected, pressure die cast aluminium housing body with optimal heat sink, with system wattage less than 25(+/-5)W with rated life of L70 @ 50,000 hours, CRI greater than or equal to 70 & with system lumens greater than 2000 and system efficiency greater than or equal to 90%.The Light fitting shall be with all required accessories suitable for mounting in on the pole arm. Weight of luminaire shall not be more than 15Kg per fitting.The luminaire should meet all the technical specifications as mentioned. The swaged pole with bracket,built-in cylindrical GI control box of same material with service door coated with epoxy zinc phosphate primer and finished with polyurethane based paint . The control gear box is prewired with DP MCB, FP connector for easy loop-in loop-out suitable for 3phase 4 wire AC supply (LT cables).The pole shall have provision for connecting the earth wire.(Make WIPRO LR 02 261 XXX 57 XX or equivalent approved make , Pole:- KLITE 8090 or equuivalent approved make).

4 Firefighting Works od52372/2018_2019 Supply, Installation, Testing and Commissioning of diesel engine driven stand by fire pump suitable for automatic operation and consisting of following: complete in all respect as required. (a) Horizontal, centrifugal, split casing type pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg/sq.cm. at highest and farthest oulet at specified flow of 2280 lpm at 60 m head conforming to IS 1520. (b)Suitable HP and RPM water cooled diesel engine with radiator conforming to relevant BS & IS standard complete with auto starting mechanism, 12 volts/24 Volts electric starting equipment, Diesel Tank, exhaust pipe extended upto 1 m. outside pump house duly insulated with 50 mm. thick glass wool with 1.0 mm. thick aluminium sheet cladding, residential silencer, instruments and protection as per specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads.

od52379/2018_2019 Supply, Installation, Testing and Commissioning of electric driven pressurisation pump (Jockey Pump ) suitable for automatic operation and consisting of following: complete in all respect as required. (a) Horizontal, centrifugal end suction type pump of cast iron body and stainless steel impeller with stainless steel shaft, mechanical seal and having a flow of 180 lpm at 60m head conforming to IS 1520 (b)Suitable HP and RPM Sqiurrel cage induction motor, TEFC, suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation as required duly plastered with anti vibration pads.

od52378/2018_2019 Supply, installation, testing and commissioning of electric driven pump set (terrace pump) and consisting of following: complete in all respect as required. Monoblock Pump rated for 900 lpm, 40m head C.I body, bronze/Gun metal impeller,SS shaft with mechanical seal, volute type with suitable HP SQ cage induction motor, suitable for operation on 415V, 3phase 50Hz, AC with IP 55 class of protection for enclosure, horizontal foot mounted type with class F insulation.M.S. fabricated common base plate, foundation bolts, anti vibration pads etc. as required. The cost shall include suitbale capacity DOL or star delta starter and one isolator near the pump with required accessories.

od52385/2018_2019 Supply, installation, testing and commissioning of pressure gauge 0-200 PSI ( 0 - 14 Kg ) range, 3/8" BSP bottom entry, 4" dial weather proof with stainless steel internals, siphon tube including all necessary fittings etc. complete as required.

od52386/2018_2019 Supply, installation, testing and commissioning of industrial type pressure switch having 1/4" BSP(F) connection IP:32 enclosure protection, phosphor bronze bellows as sensing element, SDPT contact system, switch rating 6A Inductive/lOA resistive 380 V AC, 0.2A Inductive/10A resistive 250V DC suit with ball valve etc. complete as required.

od52389/2018_2019 Supply, Installation, Testing and Commissioning of MS(Heavy C' Class) pipe IS:1239/ IS: 3589 marked including all fittings and accessories such as elbows, flanges, tees, reducers etc. conforming to IS standards complete including painting, welding, jointing and neoprene gaskets, nuts, bolts etc. as required. (for fire hydrant and sprinkler system). The pipe shall be painted with one coat of primer & two coats of post office red enamel paint. The pipe shall fixed on ceiling, walls, columns, truss etc for all heights with suitbale hangers/ supports and fasteners etc including cutting the walls/means etc and making good the same complete as required. 200 mm dia

od52390/2018_2019 Supply, Installation, Testing and Commissioning of MS(Heavy C' Class) pipe IS:1239/ IS: 3589 marked including all fittings and accessories such as elbows, flanges, tees, reducers etc. conforming to IS standards complete including painting, welding, jointing and neoprene gaskets, nuts, bolts etc. as required. (for fire hydrant and sprinkler system). The pipe shall be painted with one coat of primer & two coats of post office red enamel paint. The pipe shall fixed on ceiling, walls, columns, truss etc for all heights with suitbale hangers/ supports and fasteners etc including cutting the walls/means etc and making good the same complete as required. 150 mm dia

od52393/2018_2019 Supply, Installation, Testing and Commissioning of MS(Heavy C' Class) pipe IS:1239/ IS: 3589 marked including all fittings and accessories such as elbows, flanges, tees, reducers etc. conforming to IS standards complete including painting, welding, jointing and neoprene gaskets, nuts, bolts etc. as required. (for fire hydrant and sprinkler system). The pipe shall be painted with one coat of primer & two coats of post office red enamel paint. The pipe shall fixed on ceiling, walls, columns, truss etc for all heights with suitbale hangers/ supports and fasteners etc including cutting the walls/means etc and making good the same complete as required. 100 mm dia

od52394/2018_2019 Supply, Installation, Testing and Commissioning of MS(Heavy C' Class) pipe IS:1239/ IS: 3589 marked including all fittings and accessories such as elbows, flanges, tees, reducers etc. conforming to IS standards complete including painting, welding, jointing and neoprene gaskets, nuts, bolts etc. as required. (for fire hydrant and sprinkler system). The pipe shall be painted with one coat of primer & two coats of post office red enamel paint. The pipe shall fixed on ceiling, walls, columns, truss etc for all heights with suitbale hangers/ supports and fasteners etc including cutting the walls/means etc and making good the same complete as required. 80 mm dia

od52395/2018_2019 Supply, Installation, Testing and Commissioning of MS(Heavy C' Class) pipe IS:1239/ IS: 3589 marked including all fittings and accessories such as elbows, flanges, tees, reducers etc. conforming to IS standards complete including painting, welding, jointing and neoprene gaskets, nuts, bolts etc. as required. (for fire hydrant and sprinkler system). The pipe shall be painted with one coat of primer & two coats of post office red enamel paint. The pipe shall fixed on ceiling, walls, columns, truss etc for all heights with suitbale hangers/ supports and fasteners etc including cutting the walls/means etc and making good the same complete as required. 65 mm dia

od52399/2018_2019 Supply, Installation, Testing and Commissioning of MS(Heavy C' Class) pipe IS:1239/ IS: 3589 marked including all fittings and accessories such as elbows, flanges, tees, reducers etc. conforming to IS standards complete including painting, welding, jointing and neoprene gaskets, nuts, bolts etc. as required. (for fire hydrant and sprinkler system). The pipe shall be painted with one coat of primer & two coats of post office red enamel paint. The pipe shall fixed on ceiling, walls, columns, truss etc for all heights with suitbale hangers/ supports and fasteners etc including cutting the walls/means etc and making good the same complete as required. 50 mm dia

od52402/2018_2019 Supply, Installation, Testing and Commissioning of MS(Heavy C' Class) pipe IS:1239/ IS: 3589 marked including all fittings and accessories such as elbows, flanges, tees, reducers etc. conforming to IS standards complete including painting, welding, jointing and neoprene gaskets, nuts, bolts etc. as required. (for fire hydrant and sprinkler system). The pipe shall be painted with one coat of primer & two coats of post office red enamel paint. The pipe shall fixed on ceiling, walls, columns, truss etc for all heights with suitbale hangers/ supports and fasteners etc including cutting the walls/means etc and making good the same complete as required. 40 mm dia

od52403/2018_2019 Supply, Installation, Testing and Commissioning of MS(Heavy C' Class) pipe IS:1239/ IS: 3589 marked including all fittings and accessories such as elbows, flanges, tees, reducers etc. conforming to IS standards complete including painting, welding, jointing and neoprene gaskets, nuts, bolts etc. as required. (for fire hydrant and sprinkler system). The pipe shall be painted with one coat of primer & two coats of post office red enamel paint. The pipe shall fixed on ceiling, walls, columns, truss etc for all heights with suitbale hangers/ supports and fasteners etc including cutting the walls/means etc and making good the same complete as required. 32 mm dia

od52404/2018_2019 Supply, Installation, Testing and Commissioning of MS(Heavy C' Class) pipe IS:1239/ IS: 3589 marked including all fittings and accessories such as elbows, flanges, tees, reducers etc. conforming to IS standards complete including painting, welding, jointing and neoprene gaskets, nuts, bolts etc. as required. (for fire hydrant and sprinkler system). The pipe shall be painted with one coat of primer & two coats of post office red enamel paint. The pipe shall fixed on ceiling, walls, columns, truss etc for all heights with suitbale hangers/ supports and fasteners etc including cutting the walls/means etc and making good the same complete as required. 25 mm dia

od52405/2018_2019 Supply, laying, testing and commissioning of 'C' class heavy duty MS pipe of following size conforming to IS 1239 including fittings like elbows, tees, tapers, flanges, nuts/bolts, gaskets etc., in ground at a depth of 1m from ground level including excavation & providing cement concrete blocks as supports at 3m intervals, anticorrosive wrapping coating of 4mm thickness as per IS10221, refilling the trench etc. of following sizes complete as required -150 mm dia

od52407/2018_2019 Supply, laying, testing and commissioning of 'C' class heavy duty MS pipe of following size conforming to IS 1239 including fittings like elbows, tees, tapers, flanges, nuts/bolts, gaskets etc., in ground at a depth of 1m from ground level including excavation & providing cement concrete blocks as supports at 3m intervals, anticorrosive wrapping coating of 4mm thickness as per IS10221, refilling the trench etc. of following sizes complete as required -80 mm dia

od52408/2018_2019 Supply, installation, testing and commissioning of dual plate non-return valve of following diameter, PN16 conforming to API 594 with Cast iron/Cast steel body complete with all accessories including flanges, rubber gasket, bolts, nuts, washers etc. complete as required. 50 mm dia

od52409/2018_2019 Supply, installation, testing and commissioning of dual plate non-return valve of following diameter, PN16 conforming to API 594 with Cast iron/Cast steel body complete with all accessories including flanges, rubber gasket, bolts, nuts, washers etc. complete as required. 65 mm dia

od52410/2018_2019 Supply, installation, testing and commissioning of dual plate non-return valve of following diameter, PN16 conforming to API 594 with Cast iron/Cast steel body complete with all accessories including flanges, rubber gasket, bolts, nuts, washers etc. complete as required. 100 mm dia

od52411/2018_2019 Supply, installation, testing and commissioning of dual plate non-return valve of following diameter, PN16 conforming to API 594 with Cast iron/Cast steel body complete with all accessories including flanges, rubber gasket, bolts, nuts, washers etc. complete as required. 150 mm dia

od52413/2018_2019 Supply, installation, testing and commissioning of butterfly valve PN 16, with Cast iron/Carbon steel body complete with all accessories including flanges, rubber gasket, bolts, nuts, washers etc. complete as required and conforming to IS 13095. 50 mm dia

od52414/2018_2019 Supply, installation, testing and commissioning of butterfly valve PN 16, with Cast iron/Carbon steel body complete with all accessories including flanges, rubber gasket, bolts, nuts, washers etc. complete as required and conforming to IS 13095. 65 mm dia

od52415/2018_2019 Supply, installation, testing and commissioning of butterfly valve PN 16, with Cast iron/Carbon steel body complete with all accessories including flanges, rubber gasket, bolts, nuts, washers etc. complete as required and conforming to IS 13095. 80 mm dia

od52416/2018_2019 Supply, installation, testing and commissioning of butterfly valve PN 16, with Cast iron/Carbon steel body complete with all accessories including flanges, rubber gasket, bolts, nuts, washers etc. complete as required and conforming to IS 13095. 100 mm dia

od52417/2018_2019 Supply, installation, testing and commissioning of butterfly valve PN 16, with Cast iron/Carbon steel body complete with all accessories including flanges, rubber gasket, bolts, nuts, washers etc. complete as required and conforming to IS 13095. 150 mm dia

od52418/2018_2019 Supply, installation, testing and commissioning of butterfly valve PN 16, with Cast iron/Carbon steel body complete with all accessories including flanges, rubber gasket, bolts, nuts, washers etc. complete as required and conforming to IS 13095. 200 mm dia

od52420/2018_2019 Supply, installation, testing and commissioning of swing type Foot valve with CI body, strainer of following size confirming to IS specifications complete with gaskets, seal and accessories complete as required. 80 mm dia

od52421/2018_2019 Supply, installation, testing and commissioning of swing type Foot valve with CI body, strainer of following size confirming to IS specifications complete with gaskets, seal and accessories complete as required. 150 mm dia

od52425/2018_2019 Supply, installation, testing and commissioning of air vessel made of 250 mm dia 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia Gun metal wheel valve, with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.

od52426/2018_2019 Supply, installation, testing and commissioning of priming tank of capacity 1500 lit. made of HDPE material with outlet/ inlet connection using suitable size ball valve, water level indicator, over flow arrangement etc. completed as required.

od52437/2018_2019 "Supply, installation, testing and commissioning of First-aid Hose Reel with MS construction spray painted in Post office Red, conforming to IS 884 with up to date amendments, complete with the following as required. (a) 30 m. long 20 mm (nominal internal dia water hose Thermoplastic (Textile reinforced) Type-2 as per IS: 12585 (b) 20 mm (nominal internal ) dia gun metal globe valve & nozzle. (c) Drum and brackets for fixing the equipments on wall. (d) Connections from riser with suitable dia stop valve (gun metal) & M.S. Pipe"

od52438/2018_2019 Supply, installation, testing and commissioning of 63 mm dia, 15 mtr. Long RRL hose pipe with 63 mm dia Male and Female Gun metal couplings duly binded with wire, rivets etc. conforming to IS 636 (type-A) complete as required. (Note: the rate shall include cost of necessary supports for placing the hoses inside the shaft)

od52439/2018_2019 Supply, installation, testing and commissioning of gun metal fire hydrant valve, single headed oblique type 63 mm instantaneous outlets with female socket for hose connection and inlet side with flange suitable for 80 mm pipe flange, valve conforming to 1S:5290 complete with blank cap chain, etc complete as required.

od52443/2018_2019 Supply, installation, testing and commissioning of 25mm air release valve with all the necessary accessories complete as required.

od52444/2018_2019 Supply, installation, testing and commissioning of 4 way fire brigade collective breaching with 4 nos. gun metal male instantaneous inlet couplings complete with cap and chain as required for 150mm dia flanged out let connection and built in check valves complete in all respects as required by the standard specifications.

od52445/2018_2019 Supply, installation, testing and commissioning of hose boxes wall/pedestal type of size 750 x 250 x 600 mm made out of 16 SWG MS sheet steel with front side glass, locking arrangement and painted with approved colour completed as required and as per specifications. The pedestal shall be made of suitable channel with MS supports and mounted on a PCC foundation on ground.

od52446/2018_2019 Supply, installation, testing and commissioning of 63 mm dia Gun metal branch pipe with 20 mm (nominal internal diameter) size Gun Metal nozzle conforming to IS 903, suitable for instantaneous connection to inter-connect hose pipe coupling complete as required.

od52449/2018_2019 Supply, installation, testing and commissioning of sprinkler heads Standard response, standard coverage HORIZONTAL SIDEWALL sprinkler ;1/2" NPT, K-5.6, Chrome Finish; operating temperature at 68 deg. C.

od52453/2018_2019 Supply, Installation, Testing and Commissioning of 150mm dia Sprinkler alarm valve of Cast iron body and bronze working parts comprising of water motor alarm, bronze seat clapper, and clapper arm, hydraulically driven mechanical gong bell to sound continuous alarm when the Wet riser/Sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, GI pipe of required size, flanges, orifice plate, gasket etc. complete as required.

od52455/2018_2019 Supply and installation of ISI marked ABC Stored pressure type Fire Extinguisher 6 Kgs Capacity Mono Ammonium Phosphate based Dry Chemical Powder for Fighting ABC Class of Fire, stored Pressure type of Mild steel body pressurized by Nitrogen Gas. The Extinguisher shall have pressure gauge for indicating inside pressure with opening and closing lever of squeeze grip type with tamper proof seal, complete with wall bracket.

od52458/2018_2019 Supply and installation of Carbon-dioxide extinguisher of ISI marked 4.5 Kg capacity made of high pressure seamless steel cylinder (CCE marked ) complete with wheel type valve with one meter long braided high pressure discharge hose complete in all respects including initial fill with CO2 gas.

od53057/2018_2019 Supply, installation, testing and commissioning of Conventional Type 4 zone manual operated Fire Alarm Panel including battery backup. The panel shall be microprocessor based with its own micro controller, memory, communication module etc.The panel shall have Keypad operation, L C D unit to indicate Fire / Fault Signal of individual unit, etc complete in all respects. The item shall include 24 Volts sealed lead acid battery sufficient for 24 hrs back up with battery charger.

od53058/2018_2019 Supply, installation, testing and commissioning of conventional type Hooter with a minimum sound level of 80db at 10ft distance,interconnecting to loop cable complete as required.

od53059/2018_2019 Supply, installation, testing and commissioning of Conventional type Manual Call Point Resettable type via Special Key interconnecting to loop cable as required.

od53062/2018_2019 Supply and laying of 2x 1.5sq.mm armoured Copper FRLS cable ISI marked with proper clamping, supports and terminations appropriately above ground .

od53063/2018_2019 Supply and laying of 25mm dia PVC conduit along with accessories like PVC bends,couplers,junction box,fastners, iron staples/saddles/screws,in surface/ recess including cutting the wall/ceiling and making good the same in case of recessed conduit etc. complete as required.

od53064/2018_2019 Supply, installation, testing and commissioning of wall/ceiling mounted 6W speaker including all necessary accessories complete as required.

od53065/2018_2019 Supply, installation, testing and commissioning of wall mounted talk back unit including all necessary accessories complete as required.

od53068/2018_2019 Supply and installation of glow signage (photoluminescent)of "3M" Make such as FIRE ORDER signage of size 500*800 MM as per conventional design/ colour code on 4 mm thick foam sheet. The signage shall be either fixed on the wall with the help of screws/double tape or hanged from the false ceiling with the help of chain & screws etc. complete as required.

od53069/2018_2019 Supply and installation of glow signage (photoluminescent)of "3M" Make "FIRE ASSEMBLY POINT" of standard size (500*200 MM) as per conventional design/ colour code on 4 mm thick foam sheet. The signage shall be either fixed on the wall with the help of screws/double tape or hanged from the false ceiling with the help of chain & screws etc. complete as required.

od53070/2018_2019 Supply and fixing of Fire Emergency Evacuation Plan (Color) Printed in Photo Paper of Size A2 sandwitched in Clear acrylic sheets fixed using SS Studs and other accessories complete as required.

od53071/2018_2019 Supply and installation of glow signage (photoluminescent)of "3M" Make such as Emergency Exit/Fire Exit signage etc. of standard size (500*200 MM) as per conventional design/ colour code on 4 mm thick foam sheet. The signage shall be either fixed on the wall with the help of screws/double tape or hanged from the false ceiling with the help of chain & screws etc. complete as required.

5 Sump and Pumproom 2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

2.26.1 Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.33.1 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.33.2 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.16.1 Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.9.19 Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges

50.6.2.2 Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

6.13.2 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement : 4 coarse sand)

21.1.1.2 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.3.1 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

10.6.1 Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

10.7 Providing and fixing ball bearing for rolling shutters.

10.1 Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

10.5.1 Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angels 40x40x6 mm for diagonal braces

11.6.1 Cement plaster askirting upto 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement .18 mm thick

13.9.2 Cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement.20 mm cement plaster

13.4.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 coarse sand)

13.5.1 15 mm cement plaster on rough side of single or half brick wall of mix:1:4 ( 1 Cement : 4 coarse sand)

13.8.1 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix:1:3 ( 1 Cement : 3 fine sand)

22.5 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

13.16.1 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

13.43.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.46.1 Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

13.60.1 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.61.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

19.18.1 Supplying and fixing C.I with out frame for manholes:455 x 610 mm rectangular C.I cover ( light duty ) the weight of the cover to be no less than 23 kg

Comprehensive Annual Maintenance Contract for the MLCP system supplied and executed under this contract after the guarantee period. Job included satisfactory maintenance of the system, attending to complaints, repairs/rectification works, preventive/routine maintenance as per OEM's recommendation/ maintenance schedules, periodic visit once in every months in guarantee period and AMC period, maintence of records etc. and making the system into good working condition. The work also includes satisfactory maintenance including supply & replacement of all spares and consumables as indicated in the special conditions of contract of the tender specification.

2nd year

3rd year

4th year

5th year

6th year

7th year

8th year

9th year

10th year