General Funds

Supplying of hot applied Thermoplastic road marking compound, 2.5mm thick including reflectorising glass beads @ 250 grams with Reflectorising Glass Beads on Bituminous Surface at 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC : 35, the material should be of Burger company / Burger equivalent and must comply with the following : A) White index for the product should be in the range of 60-70 when measured against standard reference. The applied pannel 7/8 number must be submitted for checking up the white index in the department lab. In case of any major deviation. beyond acceptance limit, department reserve the right to cancel or reject the total supplied consignment of the said material and will compell the vendor has to replace the full consignment by the desired material as per approved panel at his own cost and additional demurrages may be claimed due to loss of man days (as per the rules of the department). B) Luminance factor of the material should be in the range of 80-85% at 45 degree centigrade as per AASTHOM 249. C) Crack Resistance : The applied pannel cured for 7 days under ambient condition and then should be tested as per BS3262, Part-I, 1989 and should pass at the range of "0" degree centigrade to "-10" degree centigrade D) Adhesion: Strong E) Softenning point: 102 degree centigrade F) Dried film finish: Smooth and uniform G) Night Vision: High as directed by the Engineer-In-Charge and conforming to IS: 164-1961 (1St revision reaffirmed in 1986) and clause conforming to IRC 35-1997.

Supplying & Fixing of Molded Shanks Raised Pavement Markers made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 ? DO III Dt 11.06. 1997. The height, width and length shall not exceed 50 mm, 100 mm and 100 mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum value of 700 Kgf. Fixing will be by drilling holes on the road for the twin shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer?s recommendation and complete as directed by the engineer.

Providing and fixing Cautionary / Warning sign boards size 600 mm equilateral triangle made out of Type ? IV of ASTMD 4956-09 High Intensity Prismatic Retro reflective sheeting and confirming to IRC 67:2012 for full background of White colour and letters/logos done by screen printing in Black colour, boarders by screen printing in Red colour and fixed over 4MM Aluminium Composite Material sheet having minimum 0.5 mm thick Aluminium skin on both sides with back side painted grey colour and fixed over back support frame of M.S angle 25x25x3mm all round and fixing with 35x35x4mm and mounted on a MS angle post of size 75x75x6mm with clear height of not less than 2.1 m from the ground level to the bottom of the board. The signpost should be painted with one coat of red oxide paint and 2 coats of synthetic enamel paint Black and White colour with bands of 30cm of height. The signpost shall be firmly fixed with MS base angle 35x35x4 mm in to the ground by M-15 Concrete foundation of size 450x450x600mm including cost and conveyance of all materials ,equipment, machinery and labour with all leads and lift, loading chages necessary for satisfactory completion of the work as directed by Engineer -in-Charge.

Providing and fixing Mandatory / Regulatory sign boards size 600 mm circle made out of Type ? IV of ASTMD 4956-09 High Intensity Prismatic Retro reflective sheeting and confirming to IRC 67:2012 for full background of White colour and letters/logos done by screen printing in Black colour, boarders by screen printing in Red colour and fixed over 4MM Aluminium Composite Material sheet having minimum 0.5 mm thick Aluminium skin on both sides with back side painted grey colour and fixed over back support frame of M.S angle 25x25x3mm all round and fixing with 35x35x4mm and mounted on a MS angle post of size 75x75x6mm with clear height of not less than 2.1 m from the ground level to the bottom of the board. The signpost should be painted with one coat of red oxide paint and 2 coats of synthetic enamel paint Black and White colour with bands of 30cm of height. The signpost shall be firmly fixed with MS base angle 35x35x4 mm in to the ground by M-15 Concrete foundation of size 450x450x600mm including cost and conveyance of all materials ,equipment, machinery and labour with all leads and lift, loading charges necessary for satisfactory completion of the work as directed by Engineer -in-Charge.

Painting to new walls with 2 coats of acrylic emulsion paint weather proof water based, modified acrylic with silicon additives exterior grade having VOC (Volatile Organic Compound) content lessthan 50grams/liter of approved brand and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete and cost of overheads & contractors profit for finished item of work as per SS 912 for external walls for:-External Colouring - Plastic emulsion paint - 2 Coats.