ADDN ALTN AND SPECIAL REPAIRS TO BATHROOM AND SANITARY FITTINGS AT CERTAIN BUILDINGS OF LEADINGS AND BELOW MARRIED ACCN AT SMA AND CERTAIN OTHER SANCTIONED WORKS UNDER GE NW KOCHI AT NAVAL BASE KOCHI

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for rendering 10mm thick on brick work or concrete surfaces in cement mortar 1:6 all as specified and directed .

M&L for anti-skid jointless rectified coloured ceramic tiles of size 400x400x8 mm thick as in floors, set and joint in neat cement slurry and pointed in white cement or coloured cement to match the shade over and including 10 mm thick screed bed in CM 1:4 all as specified and as directed.

M&L for glazed coloured ceramic tiles of size 450x350x7 mm thick in vertical surface, set and joint in neat cement slurry and pointed in white cement or coloured cement to match the shade, all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water any description, etc.

M&L for rendering 10mm thick on brick work or concrete surfaces in cement mortar 1:4, finished even & smooth (without using extra cement.) all as specified and directed .

Demolition of brickwork or stone masonry or PCC block masonry built in cement mortar including removal of debris all as specified and directed.

M&L for pre-cast cement concrete block masonry in Type C1, 1:3:6 (20mm graded aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:4 complete all as specified and directed.

M&L for rendering 15mm thick on brick work or concrete surfaces in cement mortar 1:4, finished even & smooth (without using extra cement.) all as specified and directed .

M&L for preparing newly plastered wall surfaces and applying three coats of white wash all as specified and as directed.

M&L for preparing newly plastered wall surfaces and applying two coats of white wash all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) n exc 1.50 sq. m each including iron mongeries, hold fast etc and making good disturbed portions of walls to match with existing surface complete all as specified and directed

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5.0mm plain colour PVC sheet reinforced with mild steel square tube, and fixing in opening as per specifications and drawing, complete all as specified and as directed.

S&F factory made solid panel PVC Door Shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying and fixing in the frame at site all as specified and directed.

S&F aluminium anodised handle, cast type, 125mm size all as specified and directed.

S & F 150mm long aluminium anodised barrel tower bolt of extruded section complete all as specified

S&F 100mm stainless steel butt hinges, medium weight, cold rold, all as specified

S&F 250mm long Mild Steel sliding door bolt, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

S&F in repairs viterous china wash down water closet pan (pedestal pattern), any colour incl plastic water closet seat, black, closed pattern with flat bottom, cover and mild steel chromium plated or aluminised hinging device, fixing bolts complete all as specified and directed.

S&F in repairs 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float, handle or two button type incl brackets and Flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified and directed.

S&F in repair stainless steel sink with draining board, 1mm thick, overall size 915x460mm and bowl size 410x330x160mm, all as specified and directed.

S&F in repairs stainless steel plate rack of size 750x900x250mm, all as specified and directed.

S&F in repairs 15mm bore Chromium plated fancy type Bib taps with crutch or butterfly handle, screwed down for iron pipe of brass ferrule complete all as specified and as directed.

S&F vitreous china wash basin, coloured, flat back of size 550x400mm including brackets all as specified and directed.

S&F in repairs brass chromium plated trap P or S pattern, 40mm bore for sinks with inlet and outlet, screwed for pipe or connections, and with one cleaning cap all as specified and directed.

S&F in repair brass chromium plated bottle trap for wash basins with inlet or outlet screwed for pipe for connection including necessary packing, union and cap (32 mm bore) complete all as specified

S&F pollar tap, fancy type, 15mm bore, brass chromium plated, screwed down, high pressure complete all as specified and directed.

S & F PVC connection 15mm bore 45cm long with brass nuts on either side complete all as specified and directed.

S&F PVC pipe 40mm dia high density (HDPE) of pressure rating 6Kg/Sqcm, concealed in walls, ceilings or in floors all as specified and directed.

S&F in repairs PVC (SWR) Nahani trap/floor trap, 75mm , plain with grating including jointng with solvent cement complete, all as specified and directed.

S&F in repairs vitreous china soap dish of apx size 160x160x90mm, embedded in wall complete all as specified and as directed.

S&F health faucet with 8 mm dia, 1m long flexible tube and wall hook all as specified and directed.

S&F 15mm bore CP angle cock, fancy type, screwed down high pressure or butterfly handle screwed down, screwed for iron pipe of brass ferrule and fixed all as specified and directed.

S&F brass chromium plated tubular towel rail, 20mm dia, D type, 60 cm long between flanges and fixed, complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25 cm, in soft/ loose soil complete all as specified and directed.

M&L for plain cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in foundations, filling and mass concrete all as specified and directed .

S&F MS plate plain 5 mm thick, cut to required size and welded to GI pipe etc complete all as specified and directed

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 10cm but n.exc 15cm long and dia of neck 11 to 15 mm complete all as specified and directed.

S&F steel work in tubular trusses incl special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240, all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified abd directed.

S&Fpre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for preparation of new steel and iron surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer all as specified and directed.

Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil all as specified and directed.

M & L for hardcore of broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface all as specified and directed.

M&L for 75 mm thick plain cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in sub base all as specified and directed .

M&L for coarse aggregate for granolithic floors, graded from 12.5mm to 4.75mm under floors or in foundations, spreading, levelling and well ramming in layers not exc 15cm thick, including watering as required complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block, any shape and size conforming to IS 15658-2006 of 60mm thickness M-35 grade using grey cement and pigments all as specified and directed.

Removal of excavated material to a distance exc 250 M and not exc 500 M and depositing where directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for pre-cast cement concrete block masonry in Type C1, 1:2:4 (20mm graded aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L for Plain cement concrete 1:2:4, type B1 (using 20mm graded aggregate) as in kerbs all as specified and directed.

M&L for pre-cast cement concrete block masonry in Type C1, 1:3:6 (20mm graded aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L for plain cement concrete Type B1, 1:2:4 (20mm graded aggregate ) as in copings all as specified and as directed.

M&L for precast cement concrete Type B1, 1:2:4 (20mm graded aggregate ) as in cover slabs, set iun CM 1:4, all as specified and as directed. (Reinforcement will be measured and paid separately)

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No.56 above, but 8mmdia bars.

M/s T.P SHAJI

SUKU CONSTRUCTIONS

T L ALOSIOUS

Vidya constructions

POOJA ENGINEERING WORKS

Oriental Constructions

Albert Rebello and Company

MS BUILDERS

ANIE JOHN CONTRACTORS