Construction of Sub-Treasury building Anni in Tehsil Anni, District Kullu H.P. (SH- Construction of main building as per Arch sketch drawing No.-95 to 97 of Job No.-7677 including site development and WS SI work etc.)

Amount

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m (one point five metre) in width or 10 sqm (ten square metre) on plan), including dressing of sides and ramming of bottoms lift up to all depth & heights, including getting out the excavated soil and disposal of surplus excavated soils as directed, within all leads including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

CONCRETE WORK: Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1:4:8 (one Cement : four coarse sand : eight graded stone aggregate 40 mm (forty millimetre) nominal size including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level. Providing and laying cement concrete 1:5:10 (one cement : five Fine sand : ten graded stone aggregate 40mm(forty millimetre) nominal size) including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:3:6 (one cement : three coarse sand) : six graded stone aggregate 20 mm (twenty millimetre) nominal size) including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Centering and shuttering including strutting, propping etc. and removal of form work for :Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and laying damp-proof course 40mm (forty millimetre) thick with cement concrete 1:2:4 (one cement : two coarse sand): four graded stone aggregate 12.5mm (twelve point five millimetre) nominal size) including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 (viscosity grade-ten) of approved quality using 1.7kg (one point seven kilogram) per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Making plinth protection 50mm (fifty millimetre) thick of cement concrete 1:3:6 (one cement : three coarse sand (zone - III) : six graded stone aggregate 20 mm (twenty millimetre) nominal size) over 75mm (seventy five millimetre) thick bed of dry brick ballast 40 mm (forty millimetre) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, leveling & dressing & finishing the top smooth including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm (fifteen centimetre X twenty two) in cement mortar 1:6 (one Cement : six Sand) and inside plastering with cement plaster 1:3 (one Cement: three Sand) including earth work and laying 10 cm (ten centimetre) cement concrete in 1:5:10 (one Cement : five Sand : ten graded stone aggregate) of 40 mm(forty millimetre) nominal size) and 7.5 cm (seven point five centimetre ) cement concrete 1:2:4 (one Cement : two Sand : four Graded stone aggregate of 20 mm (twenty millimetre) nominal size) and finished with a floating coat of neat cement complete as per standard design including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

REINFORCED CEMENT CONCRETE : Centering and shuttering including strutting, propping etc. and removal of form including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete for:-

Foundation, footing basis of columns etc. and mass concrete.

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like Floors etc. up to any thickness.

Beams, cantilever, girders and lintels sides and soffits of beams, beam hunching, cantilevers, bressumers and lintels in any depth in all height from floor.

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral staircases.

Edges of slabs and breaks in floors and walls in any width Under 20 cm (twenty centimetre) wide

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° (fifteen degree) landings, balconies, shelves, chhajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (one cement: one point five coarse sand: three graded stone aggregate 20 mm (twenty millimetre) nominal size) including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20 mm (twenty millimetre) nominal size)including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in mouldings as in cornices, windows sills etc, including setting in cement mortar 1:3 (one cement : three coarse sand) cost of required centering, shuttering but excluding the cost of reinforcement, with 1:1.5:3 (one cement : one point five coarse sand: three graded stone aggregate 20 mm (twenty millimetre) nominal size) including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and laying in position machine batched and machine mixed design mix M-25 (M-twenty five) grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works up to plinth level including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete

Providing and laying in position machine batched and machine mixed design mix M-25 (M-twenty five) grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works above plinth level up to floor V level including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:1½:3 (one cement : one & half coarse sand : three graded stone aggregate 20 mm (twenty millimetre) nominal size) including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Stone soling/boulder filling dry hand packed in under floor including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Random rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement: six coarse sand: twelve graded stone aggregate 20 mm (twenty millimetre) (nominal size) up to plinth level with Cement mortar 1:6 (one cement: six coarse sand) including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

BRICK WORK : Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in foundation and plinth in: Cement mortar 1:6 (one cement : six coarse sand) including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in superstructure above plinth level up to floor V level in all shapes and sizes in: Cement mortar 1:6 (one cement: six coarse sand) including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in foundations and plinth in : Cement mortar 1:3 (one cement : three coarse sand) including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in superstructure above plinth level up to floor V level. Cement mortar 1:4 (one cement :four coarse sand) including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete

DOORS AND WINDOWS: Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required diametre & length (hold fast lugs or dash fastener shall be paid for separately).2nd (second) Class Deodar wood including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required diametre & length (hold fast lugs or dash fastener shall be paid for separately. 1st (first) Class Deodar wood including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing 35 mm (thirty five millimetre) thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), fixing with butt hinges of required size with necessary screws, all complete as per directions of Engineer- in-charge and paneling with panels of 12 mm (twelve millimetre) thick pre-laminated particle board (decorative lamination on both sides) grade - 1, medium density flat pressed, three layer particle board FPT- I or graded wood particle board FPT- I, conforming to IS : 3087, bonded with BWP type synthetic resin adhesive as per IS : 848 and pre- laminated conforming to IS : 12823, Grade 1, Type - II marked including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing 35 mm(thirty five millimetre) thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), fixing with butt hinges of required size with necessary screws, all complete as per directions of Engineer- in-charge and paneling with panels of 12 mm (twelve millimetre) thick one side Pre-laminated particle board (decorative lamination on one side and other sides balancing lamination) grade - 1, medium density flat pressed, three layer particle board FPT - I or graded wood particle board FPT-1 conforming to IS : 3087 bonded with BWP type synthetic resin adhesive as per IS : 848 and pre-laminated conforming to IS : 12823, Grade -1, Type II marked : Shade to be matched with deodar wood as per detail including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing aluminium sliding door bolts, ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing glazed shutters for doors, windows and clerestory windows using 6 mm (six millimetre) thick DOUBLE glass unit, including ISI marked M.S. pressed butt hinge bright finished of required size with necessary screws.40mm (forty millimetre) thick 2nd (second) class deodar wood OPENABLE SHUTTER including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm (one point four) in both directions with wire of diametre 0.63 mm (zero point six three millimetre), for doors, windows and clerestory windows with hinges and necessary screws: 35 mm (thirty five millimetre) thick shutters including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm (four millimetre)thick float glass panes, including ISI marked M.S. pressed butt hinge bright finished of required size with necessary screws.40mm(forty millimetre) thick 2nd class deodar wood including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing aluminium tower bolts, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete

200X10 MM (two hundred X ten millimetre)

150X10 MM (one hundred fifty X ten millimetre)

100X10 MM (one hundred X ten millimetre)

Providing and fixing aluminium handles, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete. :

125 mm (one hundred and twenty five millimetre)

100mm (one hundred millimetre)

75mm (seventy five millimetre)

Providing and fixing Bright Finished Brass 100 mm (one hundred millimetre) mortise latch and lock, ISI marked, with six levers and a pair of anodized (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing Bright Finished Brass 115 mm (one hundred and fifteen millimetre) hasp and staple (safety type) with necessary screws etc. complete including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and Bright Finished Brass hanging type floor door stopper with necessary screws, etc. complete including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete. .

Providing and fixing ALUMINIUM hard drawn hooks and eyes complete including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete :

250mm (two hundred and fifty millimetre)

200mm (two hundred millimetre)

Providing and fixing ISI marked oxidized M.S. single acting spring hinges with necessary screws etc. complete 150MM (one hundred and fifty millimetre) including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing 19 mm (nineteen millimetre) thick water proof termite resistant commercial board box including shelves and shutters, the back side cupboard / cabinet shall be 8 mm (eight millimetre) thick ply and all the cut portions of shelves shall be finished with 6 mm (six millimetre) thick hard wood edging. The cut portion of shutters from all sides shall also be finished with 12 mm (twelve millimetre) thick hard wood edging. The shutter from outside shall be finished with 4 mm (four millimetre) thick veneer Ply of approved shade to match with paneling including stainless steel hinges and magnetic catcher with in all accessories etc. complete as per detailed drawing as per direction of Engineer-in-charge including all leads, lifts and carriage of material and other incidental including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

FLOORING AND PANNELING : Cement concrete flooring 1:2:4 (one cement: two coarse sand: four graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm (forty millimetre) thick with 20 mm (twenty millimetre) nominal size stone aggregate including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (Three Hundred X three hundred) non slippery (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm (twenty millimetre) thick cement mortar 1:4 (one Cement : four Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm (at the rate of three point three kilogram per square metre) including pointing the joints with white cement and matching pigment etc., complete including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing 1st (first) quality ceramic floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm (twelve millimetre) thick bed of cement Mortar 1:3 (one cement: three coarse sand) and jointing with grey cement slurry @ 3.3kg/sqm (at the rate of three point three kilogram per square metre) including pointing in white cement mixed with pigment of matching shade complete 300x300 (Three Hundred X three hundred) including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and laying non slippery matt finished vitrified tile of size 300x300 x 9.8mm (three hundred X three hundred X nine point eight millimetre) having with water absorption less than 0.5% (zero point five percent) and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm (twenty millimetre) thick base of cement mortar 1:4 (one cement : four coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing glazed Digital tiles 300x450 x 8 mm (three hundred X four hundred fifty X eight millimetre) thick of approved Shade and manufacturer in skirting risers of steps and dado 12 mm (twelve millimetre) thick cement mortar 1:3(one cement: three sand) and jointed with cement slurry including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete

Kota stone slab flooring over 20 mm (twenty millimetre) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1: 4 (one cement: four coarse sand): 25 mm (twenty five millimetre) thick including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Kota stone slabs 20 mm (twenty millimetre) thick in risers of steps, skirting, dado and pillars laid on 12 mm (twelve millimetre) (average) thick cement mortar 1:3 (one cement: three coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and laying 60mm (sixty millimetre) thick factory made cement concrete interlocking paver block of M -35 (M- thirty five) grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm (fifty millimetre) thick compacted bed of coarse sand, filling the joints with line sand etc. including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

ROOFING: Providing and fixing 0.62mm (Zero point six two millimetre) thick preprinted steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 (five) microns primer coating to back coast of polyester of 5 microns over 5 microns primer coating including fixing with screws, pre-painted iron J or L hooks, bolts and nuts 6mm(six millimetre) diametre with pre-painted limpet and rubber washer including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing ridges or hips 62 cm (sixty two centimetre) overall with 0.62mm (Zero point six two millimetre) thick pre-painted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyester organic coating of 20 microns (twenty microns) over 5 (five) microns primer coating + back coat of polyester of 5 (five)microns over 5 (five) microns primer coating including fixing with pre-painted iron J or L hooks, bolts & nuts 6mm (six millimetre) diametre & pre-painted G.I. limpet and bitumen washers complete with all accessories as required including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing valley 90 cm (ninety centimetre) overall 0.62mm (Zero point six two millimetre) thick pre-painted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyester organic coating of back coat of polyester of 5 (five) microns over 5 (five) microns primer coating including fixing with pre-painted iron J or L hooks, bolts and nuts 6mm (six millimetre) diametre with pre-painted G.I. limpet and bitumen washers complete with all accessories including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing 30 cm (thirty centimetre) wide, 30 cm (thirty centimetre) deep semi-circular pre-painted sheet gutter with iron brackets 40x3mm (forty X three millimetre) size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. : 0.80 mm (zero point eight zero millimetre) thick with zinc coating not less than 275 gm/m2 (two hundred and seventy five grams per square metre) including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing M.S. BP Sheet 1.66mm (one point double six millimetre) to 2mm (two millimetre) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separately) including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing tiled false ceiling of specified materials of size 610x610 mm (six hundred ten X six hundred ten millimetre) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm(at the rate of one hundred twenty grams per square metre), both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm (twenty four X thirty eight millimetre) made from 0.30 mm (zero point three zero millimetre) thick (minimum) sheet, spaced at 1200 mm (twelve hundred millimetre) center to center and cross "T" of size 24x25 mm (twenty four X twenty five millimetre) made of 0.30 mm (zero point three zero millimetre) thick (minimum) sheet, 1200 mm (twelve hundred millimetre) long spaced between main "T" at 600 mm (six hundred millimetre) center to center to form a grid of 1200x600 mm (twelve hundred X six hundred millimetre) and secondary cross "T" of length 600 mm (six hundred millimetre) and size 24x25 mm (twenty four X twenty five millimetre) made of 0.30 mm(zero point three zero millimetre) thick (minimum) sheet to be interlocked at middle of the 1200x600 mm(twelve hundred X six hundred millimetre) panel to form grids of 600x600 mm (six hundred X six hundred millimetre) and wall angle of size 24x24x0.3 mm (twenty four X twenty four X zero point three millimetre) and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm (twenty seven X thirty seven X twenty five X one point six millimetre) fixed to ceiling with 12.5 mm (twelve point five millimetre) diametre and 50 mm (fifty millimetre) long dash fasteners, 4 mm (four millimetre) GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm (eighty five X thirty X zero point eight millimetre) spaced at 1200 mm (twelve hundred millimetre) center to center along main T, bottom exposed width of 24 mm (twenty four millimetre) of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 610x610 mm (six hundred ten X six hundred ten millimetre) and 0.6 mm (zero point six millimetre) thick with 8 mm (eight millimetre) drop; made of GI sheet having galvanizing of 100 gms/sqm (one hundred grams per square metre) (both sides inclusive) and 20% (twenty percent) perforation area with 1.8 mm (one point eight millimetre) diametre holes and having NRC (Noise Reduction Coefficient ) of 0.5 (zero point five), electro statically polyester powder coated of thickness 60 (sixty) microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece. The work shall be carried out as per specifications, drawing and including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

STEEL WORK: Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, kg railings, brackets, gates and similar works including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing on wall face un-plasticised - PVC moulded fittings/ accessories for un-plasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimetre) gap for thermal expansion. (i) Single socketed pipes. 110 mm (one hundred ten millimetre) diametre including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing 75 mm x 75 mm (seventy five millimetre X seventy five millimetre) rounded hand rails in straight length complete in 1st class Indian teak wood including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing on wall face un-plasticised PVC moulded fittings/ accessories for un-plasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimetre) gap for thermal expansion including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

( I ) ( I ) Coupler :110 mm (one hundred ten millimetre)

( I ) Single tee without door :110x110x110 mm (one hundred ten X one hundred ten X one hundred ten millimetre)

( II ) Bend 87.5° (eighty seven point five degree 110 mm (one hundred ten millimetre) bend

110 mm (one hundred ten millimetre) Shoe

15 mm (fifteen millimetre) cement plaster on the rough side of single or half brick wall of mix 1:6 (one cement: six fine sand) including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete

20 mm (twenty millimetre)cement plaster of mix :1:6 (one cement: six coarse sand) including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete

6 mm (six millimetre) cement plaster of mix 1:3 (one cement : three fine sand) including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Finishing walls with 100% (one hundred percent) Premium acrylic emulsion paint having VOC less than 50 gm/litre (fifty gram per litre) and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.: New work (Two or more coats applied @ 1.43litre/10 sqm (at the rate of one point four three litre per ten square metre). Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm (at the rate of zero point nine zero litre per ten square metre) : New work (Two or more coats applied @ 1.43 litre/ 10 sqm (at the rate of one point four three litre per ten square metre). Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm (at the rate of zero point nine zero litre per ten square metre). Asian Paints including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete

Distempering with oil bound synthetic washable distemper of approved brand and manufacture to give an even shade: New work (two or more coats) over and including water thinnable priming coat with cement primer including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Finishing with deluxe multi surface paint system for interior and exteriors using primer as per manufactures specification: Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm (at the rate of zero point nine zero litre per ten square metre) over an under coat of primer applied @ 0.80 ltr/10 sqm (at the rate of zero point eight zero litre per ten square metre) of approved brand and manufacture including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing 1st (first) quality GRC/ Unistone wall cladding conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm (twelve milimetre) thick bed of cement mortar 1:3 (one cement : three coarse sand) and jointing with grey cement slurry @ 3.3kg/sqm(at the rate of three point three kilogram per square metre) , including pointing in white cement mixed with pigment of matching shade including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr /10 sqm (at the rate of zero point nine zero litre per ten square metre) over an under coat of primer applied @ 0.75 ltr/10 sqm (at the rate of zero point seven five litre per ten square metre) of approved brand and manufacture including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and applying white cement based putty of average thickness 1 mm (one millimetre), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Wall painting two coats with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ litre (fifty grams per litre) of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing 18 mm (eighteen millimetre) thick, 150 mm (one fifty millimetre) wide pelmet of coir veneer board ISI marked IS : 14842, including top cover of 6 mm (six millimetre) coir veneer board, nickel plated M.S. Pipe 20 mm (twenty millimetre) diametre (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm (twenty five X three millimetre) M.S. Flat 10 cm (ten centimetre) long fixed to pelmet with hillock wood cleats of size 100 mm x 40 mm x 40 mm (one hundred millimetre X forty millimetre X forty millimetre) on both inner side of pelmet and rawl plugs 75 mm (seventy five millimetre) long etc. including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Taking out C.I. cover with frame from R.C.C. top slab of manholes of various sizes including demolishing of R.C.C. work manually/ by mechanical means and stacking of useful materials near the site and disposal of unserviceable materials up to all leads including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm (five millimetre to ten millimetre), in the recharge pit, over the existing layer of boulders, in required thickness, for all leads and lifts, all complete as per the direction of Engineer-in-Charge including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing weep holes in brick masonry / stone masonry /plain reinforced concrete abutment, wing wall, return wall with 100 mm (one hundred millimetre) diametre PVC pipe extending through the full width of the structures with slope of 1(v):20(H) towards drawing face complete as per drawing and technical specification clauses 614, 709, 1204.3.7 including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Stone filling behind abutment, wing wall and return wall complete as per drawings & technical specification including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Water supply and Sanitary Installations: Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

15 mm (fifteen millimetre) nominal bore

20 mm (twenty millimetre) nominal bore

32mm (thirty two millimetre) nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete: 25 to 40 mm (twenty five to forty millimetre) nominal bore including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Fixing water metre and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water metre and stop cock to be paid separately) including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing Polyethylene –Aluminium- Polyethylene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C (eighty degree centigrade), including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 (one) metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge Concealed work, including cutting chases and making good the wall etc. including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

2025 (25 mm OD (twenty five millimetre outer dia) pipe

1620 (20 mm OD(twenty millimetre outer dia) pipe

1216 (16 mm OD (sixteen millimetre outer dia) pipe

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing white vitreous china water closet squatting pan (Indian type): Orissa pattern W.C. pan Hind ware No. 2004 size 58cm x 44 cm (fifty eight centimetre X forty four centimetre) of white shade of including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 (ten) litre low level flushing cistern with fitting and brackets, 40 mm (forty millimetre) flush bend, 20 mm (twenty millimetre) over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend.: Hind ware 20012 including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete

Providing and fixing wash basin of size 55cm x 40 cm (fifty five centimetre X forty centimetre)with C.I. brackets, 15 mm (fifteen millimetre) C.P. brass pillar taps, 32 mm (thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: no.10001 hind ware including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing white vitreous china flat back half stall urinal with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 (five) litre P.V.C. automatic flushing cistern Hind ware 60002 including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm (forty millimetre) C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required: White glazed fire clay kitchen sink of size 600x450x 250 mm (six hundred X four hundred fifty X two hundred fifty millimetre) including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40mm (forty millimetre) diametre including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work 40mm (forty millimetre) diametre including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete

Providing and fixing 600x450 mm (six hundred X four hundred fifty millimetre) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS: 8931 : 15 mm (fifteen millimetre) nominal bore including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing C.P. brass long nose bib cock 15 mm (fifteen millimetre) nominal bore of approved quality conforming to IS standards and weighing not less than 810 gms (eight hundred ten grams) including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing C.P. brass stop cock (concealed) 15 mm (fifteen millimetre) nominal bore of standard design and of approved make conforming to IS:8931 including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing C.P. brass angle valve 15 mm (fifteen millimetre) nominal bore for basin mixer and geyser points of approved quality conforming to IS:8931 including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing PTMT soap Dish Holder having length of 138mm (one hundred thirty eight millimetre), breadth 102mm (one hundred two millimetre), height of 75mm (seventy five millimetre) with concealed fitting arrangements, weighing not less than 106 gms (one hundred six grams) including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing 8 mm (eight millimetre) diametre C.P. / S.S. Jet with flexible tube up to 1(one) metre long with S.S. triangular plate to European type W.C. of quality and make as approved including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete. :

15mm (fifteen millimetre)

20mm (twenty millimetre)

Providing and fixing Polyethylene-Aluminium-Polyethylene PE-AL-PE Composite tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 15 mm (fifteen millimetre) nominal bore including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete 110 mm (one hundred ten millimetre) including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete 150 mm (one hundred fifty millimetre) including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing PVC floor trap of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete. 110 mm X 90 mm (one hundred ten X ninety millimetre) including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm (three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

I) 110mm (one hundred ten millimetre) diameter.

II) 150 mm (one hundred fifty millimetre) diameter.

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

I) 110mm (one hundred ten millimetre) diameter.

II) 150 mm (one hundred fifty millimetre) diameter.

Providing and fixing PVC plain double equal branch ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete. .

I) 110mm dia (one hundred ten millimetre)

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete including fixing with approved adhesive etc. complete including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

I) 110mm (one hundred ten millimetre) diameter.

II) 150 mm (one hundred fifty millimetre) diameter.

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

I) 110mm (one hundred ten millimetre) diameter.

II) 150 mm (one hundred fifty millimetre) diameter.

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

I) 110mm (one hundred ten millimetre) diameter.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20 mm (twenty millimetre) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 mm (forty millimetre) nominal size), inside plastering 12 mm thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement :two coarse sand :four graded stone aggregate 20 mm (twenty millimetre) nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm (ninety X eighty centimetre) and 45 cm (forty five centimetre) deep including C.I. cover with frame (Light duty) 450x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (thirty eight kilogram)(weight of cover 23 kg (twenty three kilogram) and weight of frame 15 kg (fifteen kilogram) including curing and carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Constructing soak pit 1.20x1.20x1.20 m (one point two zero X one point two zero X one point two zero metre) filled with brick bats including S.W. drain pipe 100 mm (one hundred millimetre) diametre and 1.20 m (one point two zero metre) long complete as per standard design including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

BUDH RAM