SPECIAL REPAIR TO BLDG NO P-09 JCO MD ACCN 28 CAMP AND P-17 OR MD ACCN DD LINE UNDER AGE BR-I AT YOL CANTT .

Amount

PART-I:- Excavation in trenches n exc 1.5 metre wide & n exc 1.5 metre in depth for foundation etc or for shafts, wells, cesspits manholes, pier holes etc n. exc 10 Sqm on plan n exc 1.5 metre in depth and getting out in any type of soil, complete all as specified.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc.25cm thick each layer of soil all as specified.

Removing excavated material exc.1.5Km but not exc. 5Km and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified.

Taking down shutters of any description exc. 1 Sqm not exc. 2 Sqm each and removing from site, all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each and removing from site, all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4 Sqm each and removing from site, all as specified.

Dismantling plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof covering, all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (But not backing), removing and rubbish of the premisses, complete including removal of debris to a distance exc 1.5 km but n.exc 2 Km, all as specified and as directed.

Dismantling timber scantlingsin fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete all as specified.

Dismantling boarding, any descriprion, fixed in any position with nails.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, all as specified.

Dismantling stone slabs and tiles of any description or thickness, laid bedded and pointed in any mortar in floors, aprons etc. including removal of debris to a distance exc 1.5 km but n.exc 2 Km, all as specified and as directed.

Demolition of stones or brick masonry or block walling, built in cement mortar including all quoins, arches etc., but excluding ashlar facing, dressed stone work etc.complete including removal of debris to a distance exc 1.5 km but n.exc 2 Km, all as specified and as directed.

Demolition of cement concrete reinforced of any description in any position complete including removal of debris to a distance exc 1.5 km but n.exc 2 Km, all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete including removal of debris to a distance exc 1.5 km but n.exc 2 Km, all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc.of any description not otherwise provided for complete all as specified.

Taking down cement plaster on brick or stone walls, ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete including removal of debris to a distance exc 1.5 km but n.exc 2 Km, all as specified and as directed.

Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.

Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.

Rolled Mild steel Joist channel, angle or tee section fixed independantly without connection plate etc . conforming to grade Fe.410-0.Gde-E-250, steel work ,all as specified.

Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed ballusters walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165, all as specified.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

4mm thick non asbestos fiber cement building boards as in ceiling fixed or laid/ inserted to aluminium frame work fixed with nails, including preparation of surface and applying three coats of white wash complete, including aluminium anodized snap grid frame work of size 605 mm x 605 mm as in false ceiling, flat or sloping (pattern as per manufacturer's catalogue/instruction), cutting holes for electrical fittings fixed on an including aluminium tee of size 25 mm x25 mm x1.5 mm as main runner, aluminium tee of size 25mmx25mmx1.25mm as cross runner and aluminium angle of size 25mmx25mmx1.25mm at the perimeter suspended from soffit at approx 900mm centre to centre with hangers 6mm dia galvanized (length as per site requirement) adjusting level fixed to roof by means of ceiling cleats made out of galvanized iron flat 40mmx3mm size, 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including necessary scaffolding all as specified and directed.

Pressed steel frames of size 105x60mmx1.25mm for door with two rebates including necessary fixing lugs, hinges, lock strike plate etc, including back filling with PCC M-15 (nominal mix) type B-0 using 12.5mm graded crushed stone aggregate complete, all as specified.

Pressed steel frames of size 125x60mmx1.25mm for door with two rebates including necessary fixing lugs, hinges, lock strike plate etc, including back filling with PCC M-15 (nominal mix) type B-0 using 12.5mm graded crushed stone aggregate complete, all as specified.

40mm thick flush shutters, solid core construction with block board core and plywood face panels commercial type on both sides covered with decorative veneer with 6mm thick teak wood lipping/frame to match type all as specified and directed.

Factory made second class hard wood (Sal) glazed and Skelton door shutters 35mm thick open rebated and prepared to receive glass gauge etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass or gauge etc., size of members of shutter as specified in clause 8.24 (a) of part-I, fitted to chowkats, complete all as specified.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side plain PVC sheet and edges shall be painted to match with plain sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 176- of MES SSR 2020 Part-II. complete all as specified.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.

Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mm x 35mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No's for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:-(i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window.(ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf.(iii) MS tower bolt 150mm long - 2 No per leaf(iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf.(v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf.(vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf.(vii) Flat iron fillets of size 20X3 mm for fixing wire gauge.(viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 26/13.Make : As per Appendix 'C'.Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.

18/19mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, 2,4 or 6 design and back plain fixed with screws to timber frame-work with 6mm thick teak wood lipping complete, all as specified and directed.

Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads, all as specified.

Sheet glass 3mm thick ordinary quality and glazing with oil putty wooden beads in squares, not exc. 0.5sqm in each pane, complete all as specified.

3mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 Sqm in each pane, complete all as specified.

Small fittings of 2nd class hard wood (SAL) such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including 50mm long, medium weight, cold rolled mild steel butt hinge, articles not exc. 200 cu.cm. each all as specified.

Brass handles, cast type, polished bright of size 75mm, all as specified.

Ball catch with 8mm dia steel ball, and brass body and striking plate including letting in and fixed.

Steel locking bolts with mild steel electrogalvanised plate and bright bolt not les than 10 mm dia size100 mm complete all as specified .

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 200mm , fixed ,all as specified.

Extruded aluminium alloy handles, fabricated type, anodised, of size 150mm, all as specified.

Mild steel Butt hinges, medium weight, cold rolled, mild steel 100mm long, all as specified.

Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm with lipping frame to match , all as specified.

Mild steel ,300mm, ordinary rat tail rod pattern springs including roller and roller plate complete, all as specified.

Applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces of any description, exc. 10cm width or girth including preparation of surfaces, all as specified.

Applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, all as specified.

Applying two coats of synthetic enamel paint over preprimed or old treated surface of steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, all as specified.

Plain cement concrete M-15, nominal mix, type B-0, using 12.5mm graded mechanically crushed stone aggregate as in floors, 25mm thick, surface finished even and fair to receive top surface, all as specified.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.18Sqm but not exc. 0.38 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) complete, all as specified.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.06Sqm but not exc. 0.11 Sqm, as in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) complete, all as specified.

Mat finish, premium quality, coloured/ printed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc. 0.18Sqm but not exc. 0.38 Sqm, as in skirting, dado etc . set and jointed in neat cement slurry and includingincluding 10mm thick rendering in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified and directed. including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed.

Glazed coloured tiles of size 350x250/450x350x7mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Marble 14 to 16mm thick , green marble , (table rubbed and polished) as in floor ,kitchen cooking platform /shelf and verticle surfaces duly machine cut in skirting /dado and like laid over and including 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade green marble type, all as specifiedand directed.

Machine cut kota stone slab flooring 18-20 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:6 (1 cement : 6 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified.

Machine cut kota stone slab 18-20 mm thick as per sample kept in GE’s office, as in vertical surfaces such as skirting/dado/riser to steps laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, laid over and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) including cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified.

Plain cement concrete M-5 nominal mix, E-2, using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete, as in sub base layer under floors, sunken floor, all as specified.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Reinforced cement concrete M-20 nominal mix ( using 20mm graded crushed stone aggregate) as in fins, fascias , louvres , parapets, and railings exc. 60cm in height, newels, balustrade, and the like etc, complete all as specified.

Formwork to to fins, louvers, fascia and sunbreakers. Rough finished surface of concrete flat for roughly finished flat surfaces of concrete, all as specified.

Second class hardwood Plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads sectional area exc 13 & n. exc 25 sqcm complete all as specified.

Second class hardwood Plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads sectional area exc 06 & n. exc 13 sqcm complete all as specified.

2nd class hard wood (Sal/Hollock) plain, solid, straight chowkats and frames, wrought, framed, rebated on solid, rounded or chamfered, put together with glue, pinned at joints with one or more rebates, all as specified.

Providing precast reinforced cement concrete M-15, type B-1 (using 20mm graded mechanically crushed stone aggregate) but in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set in cement mortar (1:4) (1 cement : 4 coarse sand), all as specified. Note :- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

PCC M-15, nominal mix, B-0 using 12.50mm graded mechanically crushed stone aggregate as, in lintels up to 1.5 metre clear span cuts, steps seismic and other similar bends, coping, bed block ,bands plates for serving hold fasts etc. and the like including weathering slighting rounded or chamfered angles and throating complete all as specified. Note:- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips , all as specified.

TMT bars 8mm to 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips , all as specified.

TMT bars 6 to 8mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in stirrups, spacers and binders, all as specified.

100mm thick Plain cement concrete M-10, nominal mix, C-2, using 40mm graded mechanically crushed stone aggregate as in sub base complete all as specified.

75mm thick Plain cement concrete M-7.5, nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in sub base complete all as specified.

Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified.

Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (1 cement : 4 coarse sand), all as specified.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) on fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement with WPC , all as specified. Note :- water proofing compound shall be measured and paid separately

Rendering plaster 15mm thick in cement mortar 1:6 (1 cement :6 coarse sand) on other than fair faces of brick wall or stone wall surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 10mm thick in cement mortar 1:3 (1 cement : 3 coarse sand) on ceiling, surface finished even and smooth without using extra cement, all as specified.

Preparation of newly plastered wall surfaces and applying two coat of exterior emulsion (acrylic emulsion paint), over a coat of primer, complete all as specified and directed.

Preparation of old untreated plastered wall surfaces and applying two coat of exterior emulsion (acrylic emulsion paint), over a coat of primer, complete all as specified and directed.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over 2mm thick wall care putty in two layers ( each Layers will be of 1mm thick) complete, all as specified.

Preparation of old untreated plastered wall surfaces and applying two coats of oil bound distemper over 2mm thick wall care putty in two layers ( each Layers will be of 1mm thick) complete, all as specified.

Three coats of white wash on newly plastered or previously undecorated surfaces of wall including preparation of surfaces complete, all as specified.

Three coats of white wash on newly plastered or previously undecorated surfaces of ceiling including preparation of surfaces complete, all as specified.

Three coats of white wash on old untreated plastered or previously undecorated surfaces of ceiling including preparation of surfaces complete, all as specified.

Supply only integral water proofing compound (ISI marked) or approved brand.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick walls, complete all as specified.

Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

All as per Serial Item No 84 above but except pipe. (Note:- Serviceable pipe retrieved from Serial Item No 18 shall be used).

Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor , complete, all as specified and directed.

All as per Serial Item No 86 above but except pipe. (Note:- Serviceable pipe retrieved from Serial Item No 19 shall be used).

Sink with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; ncluding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm, all as specified.

20mm bore Curtain rails, powder coated mild steel, chromium plated with fixing brackets, stops and roller etc. fixed in repair complete all as specified.

Brass Chromium Plated, tubular towel rail, 20mm dia, D type, 60cm long between flanges, with brackets, fixed with chromium plated screws, fixed in repair, complete all as specified.

Bib taps, fancy type 15mm bore, cast copper alloy with crutch or butterfly handle, screwed down, chromium plated screwed for iron pipe or for brass ferrule and fixed in repairs , all as specified

Stop/Angle valve, cast copper alloy, chromium plated, fancy type screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified.

Stop/Angle valve, cast copper alloy, chromium plated, concealed type screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified.

Chromium plated brass shower rose, fancy type, 125mm size 195mm long with bends of 450 with flange suitable for 15mm bore pipe with swivel joint fixed to pipe, complete all as specified.

Soap dish, brass chromium plated, fixed to plugs with chromium plated, brass screws, all as specified.

Steel plate rack of size 600mmx750mmX250mm made of stainless steel 1.00mm thick fixed with plugs,washers and steel screws including fixed in wall with screws ands PVC sleeve of required or fixing arrangement complete all as specified

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified

Rotational moulded polyethylene water storage tank 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding PVC float ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/ PVC storage tank, all as specified.

Water profing treatement of sunken portion/water tank padding using SHALIURETHANE-BTD OF STP MAKE OR EQUIVALENT as approved by GE, high solid content single component water based liquid applied elastomeric water proofing membrene as ASTMC 836 and ASTMD 6083, thickness of the memberane shall be 1.5mm, having solid content of more than 80% elongation of 500+(-) 50% laid over reinforcing layer on non woven geo-textile mesh of 40/50 50gms, including applying self primer coat by diluting with 1:1 ratio @ 0.2 kg per sqm and suface preparation including cleaning of existing treatement complete all as per specified and directed by Engineer -in -Charge.

Rendering cement plaster 10mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers ( 5mm thick first layers and 5mm thick 2nd layer) mixed with WPC , all as specified. Note :- water proofing compound shall be measured and paid separately

Mild steel galvanized iron water tubing 32mm bore with screwed & socket joints, medium grade, as in spout of sunken floor complete, all as specified and directed.

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-I using 20 mm graded crushed stone aggregate and including PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve , float and handle with brackets,32mm dia flushing pipe, anti-syphonage pipe with fittings,complete all as specified, connections to trap and to flush pipe, etc complete, all as specified.

Wash basins, Vitreous China (Flat back type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with CP coupling nuts at both ends, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps fancy type, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed , complete all as specified.

Cast iron soil, waste and vent sand cast pipes of 100mm bore in any length with or without ears, with cement joints, fixed to walls with MS clamps etc , including taking down old existing complete all as specified .

Cast iron soil, waste and vent sand cast pipes of 75mm bore in any length with or without ears, with cement joints, fixed to walls with MS clamps etc , including taking down old existing complete all as specified .

Cast iron soil, waste and vent sand cast pipes of 100mm bore in any length with or without ears, with cement joints, laid in trenches or in floors complete, including taking down old existing complete all as specified .

Cast iron soil, waste and vent sand cast pipes of 75mm bore in any length with or without ears, with cement joints, laid in trenches or in floors complete, including taking down old existing complete all as specified .

PVC (SWR) pipes single socketed,in any length with rubber ring joints, laid in trenches or in floors bore 75mm complete, complete, including taking up or down old pipe , all as specified.

PVC (SWR) pipes single socketed,in any length with rubber ring joints, laid in trenches or in floors bore 110mm complete, complete, including taking up or down old pipe , all as specified.

PVC (SWR) bends any radius, 110mm bore( fitted with oval access door, all as specified.

PVC (SWR) bends any radius, 75mm bore jointed with solvent cement( fitted with oval access door all as specified.

PVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, provided with oval access door all as specified.

PVC (SWR) junction single, (Single T) equal or unequal, 75mm bore, provided with oval access door all as specified.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement, dia of outlet 75mm, all as specified.

75mm bore Cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access doors complete all as specified .

100mm bore Cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access doors complete all as specified .

100mm bore Cast iron Branch pieces, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified .

75mm bore Cast iron Branch pieces, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified .

Cast iron vent cowl 75mm, complete all as specified.

Salt-glazed stoneware gully traps, round mouthed, type 'P ', of size 150mmx 150mm, complete all as specified.

40mm bore , High density polyethylene pipes (HDPE) of pressure rating 6 kgf/Sqcm fixed complete to walls, ceilings or in floors etc including short lengths, with all pipe fittings uch as ends, elbows, unions, tees, reducing tees, adoptors, sockets, plugs, hose clips etc. and fixing to walls etc, complete with saddles (snap clips), wall clips, hooks, protective mild steel tube sleeves and cutting through walls, floors and their making good, complete all as specified.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised Width of flaps (when open) in 40mm, all as specified.

Reinforced concrete pipes, class NP-3, laid and jointed in cement mortar 1:20 complete with collars, bore of pipe 150mm, including demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete ) set in cement motar Internal dia of pipe 150 mm Complete, all as specified.

Plain cement concrete M-7.5 type D-2 nominal mix using 40mm graded aggregate as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for internal dia of pipe 150 mm, all as specified. (i) The unit rate include for use of form work. (ii) For width and depth of PCC bed - refer preamble (a) (i) (ii) on page 356 of SSR Pt-II).(iii) Haunching shall be as per MES SSR-part-I/Part-II

Plain cement concrete M-15 nominal mix, type B-1 using 20 mm graded mechanically crushed stone aggregate as in surface channel and drains (including necessary form work) including forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds etc. all as specified. complete, all as specified.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment laid over and including 50mm thick sand cushion, joints of tiles filled with dry sand and compacted with mechanical vibrator complete all as specified and directed.

Plain cement concrete M-7.5, nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete, as in sub base layer under floors, sunken floor, all as specified.

Gun metal, globe or gate valves , screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions and fixed complete, all as specified.

Taking down cement plaster/decayed concrete from RCC roof projections/upward parapet walls/down facia/soffits and fins of RCC chajjas/beams/columns/balconies etc. Supply and fixing by means of nailing wire netting of galvanised wire 1.40mm dia and mesh size 20mm and brushing neat cement slury with 3.00 Kg of cement/sqm and M&L for 20mm thick cement rendering in two layers of 10mm each (top/final layer shall be rendered after final setting of under layer) in Cm 1:3 on concrete surfaces including scaffolding at a height upto 7.00 mtrs ect complete all as specified and directed.

Part-IITaking down point wiring with aluminium/ copper conductor for light point, fan & socket point/ power point etc. complete including light fiitings any type,switches, sockets, holders, (batten or pendent type), ceiling rose, switch board , bell/buzzer,bell push, tube light fitting ,regulator etc. and making good to the disturbed surfaces of wall/ floor etc. to match with existing surfaces including white wash/ colour wash/ distempering to match with existing wall/ floor/ ceiling finishes and all as specified and directed.

Taking down sheet metal enclosure DB, MCB, main switch etc and making good distrubed surfaces to match with existing surfaces, complete all as specified.

Point wiring with 1.5 Sqmm copper conductor FRLS (Multi strand) PVC insulated ISI Marked unsheathed cable in and including casing-n-caping medium grade, ISI marked of suitable size with all fittings/ accessories and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as phase, neutral and earth wire connected to common earth dolly and including concealed pressed steel/ cast iron of suitable sizes terminal boxes made from 1.60 mm thick sheet for mounting of switches, sockets, fan regulators, light fittings etc. covered with 3mm thick plastic laminated sheet (Make Hylum or equivalent ISI marked) for one light point or one fan point or one bell point, independent, controlled by one way switch/ push button complete all as specified and directed. Note:-i) Wiring colour code i.e Red/Yellow/Blue for phase , Black for neutral and Green for earth shall be maintained. ii) The wire from switch board to ceiling rose shall be of 2x1.5Sqmm +1x1.5sqmm rates for the same shall deemed to be included in item .

All as per serial item No '133' above, but for one 3 pin 5 Amps socket outlet on the same board all as specified and directed.

All as per serial item No '133' above, but for one 3 pin 5 Amps socket outlet on the independent board, all as specified and directed.

All as per serial item No '133' above, but for one light point controlled by two way switches, all as specified and directed.

All as per Srl item No. '133' hereinbefore but for 3 pin 15 amps socket out let on independent with 2.5 Sqmm PVC copper conductor cable and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.

Switch piano flush type, single pole, one way, 5/6 Amps, all as specified.

Switch piano flush type, single pole, two way, 5/6 Amps, all as specified.

Switch socket outlet Two -in -One 3 pin 5 amps flush type, 230 volts AC multipurpose all as specified.

Switch socket combination 5 Pin, 5 Amp & 15 Amp flush type controlled by one switch, all as specified.

Ceiling fan regulator step type, electronic type varying 5 Speeds 230 Volts, 50Hz, suitable for 1200/ 1400 mm sweep ceiling fans, all as specified.(Makes as mentioned in Appendix 'C').

Ceiling rose, three phase, PVC/Polycarbonate, insulated body, all as specified.

Switch , bell push, flush type, 5 Amps, all as specified.

Bell electric, ding dong AC 230V, single pole, all as specified.

Sheet metal enclosures factory made for DBs when MCBs to be used, single pole and neutral (double Door), 12 way, 240 volts with 200 Amp rated bus bar, all as specified.

Sheet metal enclosures powder coated suitable for MCCBs 125 Amp TPN as incomer 4 way, 415 volts with 200 Amp rated bus bar, double door with detachable gland plate, all as specified.

MCB SP 6 to 40 Amp, 240 Volts, 10 KA all as specified. Note:-The connection to the MCBs shall be through thimble/lugs for and rate for the same shall deemed to be included in quoted rates

MCB SPN 6 to 32 Amp, 240 Volts, 10 KA all as specified. Note:-The connection to the MCBs shall be through thimble/lugs for and rate for the same shall deemed to be included in quoted rates

MCCB TPN 125 Amp, 415 Volts, 50 Hz, 16 KA all as specified. Note:-The connection to the MCBs shall be through thimble/lugs for and rate for the same shall deemed to be included in quoted rates

Replacement of Sub main wiring with two single core PVC insulated cable 1100 volts grade with copper stranded FRLS conductor of size 6 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 6 Sqmm and drawn into and including surface PVC casing & capping of suitable size with all fittings/ accessories, junction boxes 1 to 4 way 25mm dia and connected to common earth dolly, complete and as directed.Note :- Two run (each run of 1 RM) of 6 sqmm copper conductor and one RM of earth wire of 6 Sqmm, shall be measured as one RM).

Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver all in one fxture, 9/10 watt LED and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete , all as specified.

Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver all in one fxture, 18/20 watt LED and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete , all as specified.

Taking down water storage heator of 25 ltrs capacity from electrick socket and disconnecting from PVC connection and screew down kept aside for reuse at same / different location after cleaning/scrapping of old paint/dust and painted with two coat of super enameled painting( white Colour) by spray gun , refixing the same duly grouting nuts, bolts washers and connecting to existing water connection complete, all as specified and as directed by Engineer-in-Charge. acomplete all as specified.

Taking down ceiling fans//exhaust fan of 1200 /250/300mm sweep of any make/ Model from fan hook/ wall dismentling blade opening of motor for overhauling/servicing , and then properly cleaning alll parts and greasing , oiling of bush & bearings after opening of the fan including reassembling and Painting of ceiling fans/exhaust fan after due preparation complete at site with super enamel synthetic white paint by spray gun including filling cavities with filler, one coat after cleaning all dust etc and writing MES No with black paint and than re-hanging and reconnecting of fan with new flexible cord of suitable size from ceiling rose to connector , complete all as directed by Engineer-in-Charge.

Material and labour for rewinding of ceiling fan of any make/model/sweep including removal of existing burnt winding carefully from slots, cleaning the slots throughly with suitable cleaing agent, applying slot inslation and rewinding with super enameled insulated copper wire of same gauge / same number of turns as existing and connecting the coil suitable to operate on 230VC, single phase, AC supply including all winding, insulating material and impregnation of insulating varnish as specified of any make, type, model and applying air drying the winding throughly including transportation from site to workshop of rewinding 1200/1400 mm sweep , complete all as specified .

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one SPN MCB 20 Amps, complete all as specified.

45Watt energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source nd lens enbeddedPC cover having IP65 protection and impact resistance of IK07, suitable for pole dia 43mm(max) connecting with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting including bracket complete all as specified and as directed

Replacement of motor suitable for plastic body exhaust fan of size 200/250mm sweep and making necessary connection complete all as specified and as directed.

Replacement of blade suitable for plastic body exhaust fan of size 200/250mm sweep and making necessary connection complete all as specified and as directed.

Replacement of plastic body suitable for exhaust fan of size 200/250mm sweep and making necessary connection complete all as specified and as directed.

Supply and replacement of louvers suitable for plastic body exhaust fan of size 200/250mm sweep and making necessary connection complete all as specified and as directed.

Taking down AC meters. Checking and repairing at site by repair/replaceing of contects, terminals and indicators, glass covers, plate screws, electronic circuits etc and re-fixing in same position, complete all as specified.

XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 35 Sqmm 3.5 core laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc including testing after laying complete including taking out old unserviceable cable, all as specified.

Sand cushioning to under ground cables, 8 cm thick layer before laying and testing the cable and 15 cm thick after laying and testing of the cable in trenches complete all as specified in Clause 19.75 of MES SSR 2009 Part-I and directed by Engr-in-Charge.

Sub class 'B' bricks old size, as cable protection cover, laid dry, flat, transversally along the length of cable, on sand cushioning, with width equal to the length of the brick, complete all as specified and directed.

Mild steel galvanised light grade 50mm dia tubing with all fitting; laid in trenches, across road or on pole complete all as specified.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15 mm bore including provn of concrete pit in plain cement concrete M-20 type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of rainforced cement concrete M-20 reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion. NOTE :- Item of earthing includes the cost of 7.5 metre long galvanised iron earth wire 4mm size and protection pipe of 15mm bore galvanised iron light grade and earth work.

Pardeep Furnishers and Interiors

m/s Sohan singh barwal and Brothers

MM Constructions

Niraj Kumar and Co

M/S MADAN GOPAL and CO