WORK SERVICES FOR IMPROVEMENT TO CERTAIN MARRIED ACCN AT AF STN JAMNAGAR

Amount

Taking down chowkhats or frame with shutter (without taking off shutter from the frame) area n.exc 1.5 Sqm each, complete all as specified and directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) area exc 1.5 Sqm but n.exc 4 Sqm each, complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but n.exc. 2 Sqm each complete complete all as specified and directed.

Taking down shutters of any description not exc 1 sqm each complete all as specifed & directed.

Dismantling of floor, hearth or wall tiling or stone slab laid, bedded & pointed in any mortar including demolition of cement mortar bedding or backing coat, including removal of debries to outside MOD land complete all as specified and directed.

Demolition of cement concrete in ground floor and pavings not exc 15 cm thickness below or above ground level, including removal of debries to outside MOD land complete all as specified and directed.

Demolition of brick / stone / PCC block masonry built in cement mortar including all quoins, pillars, arches etc. including removal of debries out side MD land, complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position and( reinforcement not cut in chajja/fins to facilitate demolition) including removal of debries to outside MOD land complete all as specified and directed. NOTE:- The rate quoted by the contractor shall be deemed to be included segregation of reinforcement from concrete.

M & L for RCC type M-20 nominal mix concrete (1:1,1/2:3) using 20mm graded aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M & L for RCC type M-20 nominal mix concrete (1:1,1/2:3) using 20mm graded aggregates as in Chajjas,and the like complete all as specified and as directed.

M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exceeding 200mm thick (horizontal or sloping) rough finished surfaces of concrete complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges flat fair finished surfaces of concrete complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5cm but n.exc 10cm wide complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6, type C2, using 40 mm graded stone aggregate as in plinth protection surfaces finished even and smooth without using extra cement including filling the joints complete all as specified and directed.

M& L for forming 6 mm wide and 10 mm deep and joints filed with bituminious mastic (1 part of bitumen and 2 part of sand )in plinth protection complete all as specified and directed.

M&L for Brickwork with subclass ‘B’ bricks, old size straight or curved on plan exc 6m mean radius built in cm 1:4 complete all as specified.

M&L for Brickwork with subclass‘B’ bricks, straightor curved on plan to anyradius in half brick thickwalls built in cm 1:4 complete all as specified.

Hardcore of broken stone or boulders gauge n.exc 63 mm, deposited, spread and leveled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

S&F second class hardwood plain, solid, straight chowkhats and frames, wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

M&L for factory made flush shutters,30mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides with 6mm teak wood lipping fixed with nails complete all as specified and directed.

M&L for factory made flush shutters,30mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides with 6mm teak wood lipping including 0.90mm thick decorative laminate type 1, of surface finish, colour as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S & F 25 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, with 0.90mm thick decorative laminate type 1, commercial type on both sides 6mm teak wood lipping fixed with nails of surface finish, colour as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S&F 30 mm thick factory made second class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass / gauge, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkhats complete. complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples to wooden shutters complete all as specified and directed.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS tube supplying and fixing in opening as per specification and drawing in SSR Part-II complete all as specified and directed.

S&F Factory made solid PVC moulded door shutter with partical board core consisting 28 to 30mm thick (stiles) with 2, 4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in the frame at site as per specification complete all as specified and directed.

S&F 100 mm size Stainless steel butt hinges medium weight, fixed to chowkhat complete all as specified and directed.

S&F 200 mm long aluminium anodised barrel tower bolt complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolt complete all as specified and directed.

S&F 150 mm long aluminium handle fabricated type anodised complete all as specified and directed.

S&F 100 mm long aluminium handle fabricated type anodised complete all as specified and directed.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 300 mm, size mild steel ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

S&F 140 mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F 75 mm size cold rolled mild steel butt hinges medium weight, fixed to chowkhat all as specified and as directed.

S&F Continuous (Piano) hinges, mild steel, bright finished or electro galvanized, width of flaps (When open) 30 mm complete all as specified and directed.

S&F 100 mm size Hasp and staples, safety type, aluminium anodised including bolt to hinge plate and fixed with screws etc,complete all as specified and directed.

S&F 100 mm long aluminium anodised barrel tower bolt complete all as specified and directed.

S&FPowder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever requiredincluding cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and as specified and directed.

S&F providing and fixing poweder coated aluminium(minimum thickness of poweder coating 50 micron) for shutters of doors,windows & and ventilators including providing and fixing hinges/pivotes/handle and making provision for fixing of fitting whereever required including the cost of EPDM rubber/neoprene gasket required(fitting shall be paid separately) with extruded built up standered tubular sectios/ appropriate Z section and other sections of approved make conferming to IS 733 and IS : 1285 , fixing with dash fasteners of required dia and size including necessary filling up the gaps at juctions , ie at top , bottom and sides with required EPDM rubber neoprene gasket etc . Aluminium sectios shall be smooth , rust free , straight , mitred and jointed mechanically wherever required including cleat angle, luminium slap beading for glazing/ panelling , C.P. brass stainless steel screws all complete as per architectural drawing complete all as specified and directed.

S&F 5mm figured glass , pin headed type and glazing with oil putty in squaren. exc 0.50 m in each pane for windowes/ventlators complete all as specified and directed.

M&L for preparation of new wooden surfaces, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surfaces, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth and applying one coat of Synthetic enamel paint complete complete all as specified and directed.

S&F mild steel framed work such as grills gratings etc with ends of bars shouldered and / or riveted or forged into spiked framed guard bars barred iron doors ladders framed blasters walkways railings framework of water tanks and similar work conforming to Fe 290 Grade E-165 complete all as specified and directed.

S&F Mild steel flat iron as in hold fast and similar work fixed to chowkhat complete all as specified and directed.

M & L for cutting holes in brick wall built in cement mortar or stone wall built in lime mortar exc half brick and n. exc one brick thick for inserting holdfasts and making good dismantling portion in cement mortar 1:3 or cement concrete 1:2:4 complete all as specified and directed.

M&L Preparation of old steel or iron surfaces over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint ,etc complete all as specified and as directed

S&F 18/19 mm thick Block boards, grade 1 quality, e x t e r i o r grade, with decorative face veneer on both faces, fixed with Nail/screws to timber frame complete all as specified and directed.

Extra over rates of 18/19 mm thich block board or veneered particle board for external teak wood lipping,6mm thick fixed with nails complete all as specified and directed.

S&F Magnet catches sutable for kitchen cabinetcomplete all as specified and directed.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, polished complete all as specified and directed.

S&F kitchen basket fabricated with stainless steel section (SS-304), best quality (as per sample kept in GE, s office) of size 430 mm x 508 mm x 100 mm for different use such as placing plain plate / dish / cup & saucer /cutlery / thali etc fixed in position with and including one pair telescopic Channel of size 450 mm (when closed), mild steel chromium plated, roller type, heavy duty as directed complete all as specified and directed.

S&F kitchen basket fabricated with stainless steel section (SS-304), best quality (as per sample kept in GE,s office) of size 450 x 500 x 150 mm for different use such as placing plain plate/dish/cup & saucer/cutlery/thali etc fixed in position with one pair telescopic Channel mild steel chromium plated, roller type, heavy duty all as per sample kept in GE Office complete all as directed.

S&F kitchen basket fabricated with stainless steel section (SS-304), best quality (as per sample kept in GE, s office) of size 430 mm x 508 mm x 200 mm for different use such as placing plain plate / dish / cup & saucer /cutlery / thali etc fixed in position with and including one pair telescopic Channel of size 450 mm (when closed), mild steel chromium plated, roller type, heavy duty as complete all as specified and directed.

S&F in repair Stainless steel curtain rods of 25mm dia complete all as specified and directed.

S&F SS ornamental stainless steel holding brackets for 25 mm dia curtain rods complete all as specified and directed.

S&F Stainless steel peg set of 5 hooks including chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms).

Demolition of cement concrete of any description and in any position not otherwise specifically provided for including removal of debries to outside MOD land complete all as specified and directed.

M &L for plain cement concrete type E-2 (1:5:10), using 40 mm graded stone aggregate, for filling sunken portion of toilet and similar work complete all as specified and directed.

M&L for providing water proofing tratment of sunken portion of WCs, bathroom etc. by applying cement slurry mixed with Acrylic based polymer modified cementitious composite compouned coating of make as approval in Technical Instruction 5/2003 by adding: (a) 15mm thick rendering CM (1:4) with Liquid water proofing compound 200ml per 50kg bag of cement on floor and wall , finishing the surface even and smooth without using extra cement. The surface shall then be cured and allowed to dry. (Note: Water proofing compound shall be measured and paid separately). (b) First layer of slurry of cement @ 0.488 kg/sqm mixed with Acrylic based polymer modified cementitious composite compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hrs. (c) Second layer of slurry of cement @ 0.242 kg/sqm mixed with Acrylic based polymer modified cementitious composite compound @ .126 kg/sqm. This layer will be allowed to air cure for 4 hrs followed with water curing for 48 hrs including complete removal of old treatment to sunken portion etc complete all as specified and directed.

M&L for 25 mm thick plain cement concrete 1:2:4, type B0 (using 12.5 mm graded stone aggregate) as in flooring in leveling course complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. and brushing neat cement slurry with 3.0 kg of cement per sq metre.

M&L for Non skid,(Joint Free) coloured ceremic tiles 7 to 8 mm thick (Square / rectanguler) polished area of each tile exceeding 0.06 sqm but not exeeding 0.11 sqm as in floors etc laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete all as specified and directed.

M&L for Non skid, (Joint Free) coloured ceremic tiles 7 to 8 mm thick (Square / rectanguler) polished area of each tile exceeding 0.11 sqm but not exeeding 0.18 sqm as in floors etc laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete all as specified and directed.

M&L for coloured glazed ceramic(Joint Free) tiles 7 mm to 8 mm thick (square / rectangular) of size 350x 250x 7mm/ 450X 350X 7mm thick as in skirting / dado etc laid over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete all as specified and directed.

M&L for green Marble work 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in coloured cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in 15 mm cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L 20-25mm thick machine cut kota stone slab flooring, treads etc over and including 15 mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L 20-25mm thick machine cut kota stone slab in riser of steps, skirting,dado and pillar laid over and including 10 mm thick plaster in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Labour only for rounding to edges of stone slabs one edge, such as in steps cooking plateform, and other similar situation complete all as specified and directed.

S&F in repairs 15mm bore bib taps ,fancy type of cast copper alloy chromium plated with capstan handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair 15mm size bib tap cast copper alloy chromium plated, with capstan head , screwed down , screwed for iron pipe complete complete all as specified and directed.

S&F in repair 15mm bore dia stop valve/angle valve cast copper alloy chromium plated, fancy type screwed down high pressure with capstan handle, screwed both ends for iron pipe or for union complete all as specified and directed.

S&F 15mm bore dia stop valve/angle valve cast copper alloy chromium plated, fancy type screwed down high pressure with capstan handle, screwed both ends for iron pipe or for union complete all as specified and directed.

S&F Health faucet (ABS Body) mild steelchromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repair 15mm stop cock , fancy type chromium plated with long shank and cup (Concealed)complete all as specified and directed.

S&F in repair 20mm bore Stop valves, cast copper alloy screwed down high presure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed

S&F 15mm cold and hot wall mixer brass chromium plated with bend pipe including all accessories complete as directed.

S & F in repair 10 Ltr capacity PVC valveless , syphonic action type , flushing cistern low level white with inlet ball valve float and handle including bracket , 32 mm dia pvc flushing pipe complete all as specified and directed.

S& F in repairs brass chromium plated overhead shower 100 mm size with 225 mm arm and flange for 15mm inlet pipe complete complete all as specified and directed.

S&F in repair white vitreous china wash hand basin of size 550 x 400 mm, fixed over & including MS brackets comprising of the following items :- (a) Waste fitting 32 mm dia chromium plated with long screwed shanks and fly nut, flange end, bedded in red lead cement and other end fixed complete. (b) 15 mm size Pillar tap cast copper alloy with capstan head, chromium plated screwed down high pressure with or without lettered hot or cold with long screwed shank and fly nut screwed for iron pipe complete all as specified and directed. (c) 32 mm dia Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed

S&F in repairs 32mm bore dia light grade GI pipe cocealed in wall or laid in floors complete all as specified.

S&F in repair stainless steel kitchen plate rack of size 31"x24"x10" deep, fabricated with 0.63 mm sheet fixed in position on wall complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheel galss shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed..

S&F in repair soap dish, any type, fixed to plugs with chromium plated brass screws as complete all as specified and directed.

S&F in repairs white Vitreous china wash down water closet (pedestal pattern) with fixing bolt, with plastic water closet seat, white, closed pattern with flat bottom, and cover with aluminised hinging device, including all connections complete complete all as specified and directed.

S&F in repairs white vitreous china squatting pan ‘ORISSA’ pattern of size 580 mm x 440 mm white with integral foot rests and 100 mm dia CI P or S trap including all connection and provision of lime concrete base complete all as specified and as directed.

S&F brass Chromium plated tubular Towel rail 20 mm dia D type 600mm long bettwen flange fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and directed.

S&F in repairs stainless steel sink, 1.00 mm thick for kitchen, with plug, washers and wastes coupling, including bedding in cement mortar on to draft wall or including fixing cantilever brackets, connecting union to pipe etc, overall size 495 mm x 420 mm, with bowl size 410 mm x 330 mm x 160 mm, complete complete all as specified and directed.

S&Fin repair PVC connection 15mm dia and 45 cm long with 2 Nos PTMT nuts, complete all as specified and directed

Dismantling water tanks of capacity exc 250 and not exc 500 litres removal to store complete all as specified and directed.

Supply and fix 500 litres capacity triple layer (white), rotational molded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc. complete all as specified and directed.

M&L for Cutting chases, of girth not exceeding 10 cm for concealed water tubing or concealed conduit wiring, etc. in stone / brick masonry wall built in cement mortar and making good, disturbed surface in Cement mortar 1:3 complete all as per specified and as directed.

Supply and fixing 15mm bore galvanised steel water tubing, medium grade including necessary fittings such as GI bends, tee, union etc fixed on wall / floor complete and connecting to water supply pipe line including concealed in wall including taking down old existing unserviceable tube complete all as specified and as directed.

Supply and fixing 20 mm bore galvanised steel water tubing, medium grade including necessary fittings such as GI bends, tee, union etc fixed on wall / floor complete and connecting to water supply pipe line including concealed in wall including taking down old existing unserviceable tube complete all as specified and as directed.

Supply and fixing 25 mm bore galvanised steel water tubing, medium grade including necessary fittings such as GI bends, tee, union etc fixed on wall / floor complete and connecting to water supply pipe line including concealed in wall including taking down old existing unserviceable tube complete all as specified and as directed.

S&F in repair ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass ferrule and fixed 20mm dia complete all as specified and directed.

S&F Stack clamp made out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall, suitable for 100 mm bore pipe complete all as specified and as directed by the Engineer – In – Charge

S&F in repair 100mm cast iron sanitary connection socket to fit WC out-let complete all as specified and as directed.

Taking down CI/rain water pipes/PVC pipes (any size or pattern) including all fittings, heads, shoes, bends, swan necks, complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed,in any length with rubber ring joints, fixed in wall including GI clamps of approved shape and size complete all as specified and directed.

S&F 110mm dia PVC (SWR) bends/shoes any radius complete all as specified and directed..

S&F CI/Soil waste pipe 75mm dia spun cast iron any length with or without ears with cement joint fixed on wall complete all as specified and directed.

S&F 75 mm dia spun cast CI bend/tees of any radius, jointed with neat cement paste complete all as specified and directed.

S&F CI/Soil waste pipe 100mm dia spun cast iron any length with or without ears with cement joint fixed on wall complete all as specified and directed.

S&F CI bends/tees 100mm dia long (any radius) diminishing pieces of tapers large bore measured fited with oval access door complete all as specified and directed.

S&F in repair 75mm cast iron Nahani trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F in repair grating square fitting of size 150 mm made in two parts for smell and mosquito proofing with minimum 25mm water seal of PTMT. (Minimum weight 100gms) complete all as specified and directed.

S&F 40mm dia low density polyethylene pipes (LDPE) of pressure rating 6 kg/cm2 fixed complete to walls, ceilings or in floors all as specified & directed.

Taking down cement plaster in cement or cement lime mortar on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc, including removal of debries out side MoD land complete all as specified and directed.

Raking out joints/ pointing to random rubble or polygonal rubble uncoursed or brought up to coursesincluding removal of debries out side MoD land complete all as specified and directed.

M&L for rendering 15 mm thick in two layers Ist 10 mm thick and 5 mm final coat mixed with WPC on brick/stone/ PCC block masonry wall surface in cement mortar 1:4, finished even and smooth without using extra cement (water proofing compoundshall be paid for separetly complete all as specified and directed.)

M&L for rendering 15mm thick on other than fair faces of brick work or concrete surfaces or stone masonry surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 5mm thick rendering in cement mortar 1:3 on concrete surface of ceiling, finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls & applying two coat of Distemper oil emulsion over a coat of primer on wall surfaces complete all as specified and directed.

M&L for complete removal of existing treatment from wall including brooming down or steel wire brushing, scraping down complete including preparation of old surfaces and applying two coat of Oil bound Distemper over a coat of primer on wall surfaces complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfacestwo coats of Acrylic emulsion (exterior weather coat) paint of any tint as approved over one coat of primer applied as per manufacturer's instruction complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling (plastered or unplastered) by brooming down , scrapping down smoke soot, moss and efflorescent salts and trading oil and greasy spots etc and applying two coat of white wash on ceiling complete all as specified and directed.

M&L complete removal of existing treatment from external surfaces on walls by wire brushes & stopping of surfaces and levelling/edging the disturbed places/edges using necessary filling compound of Allek Putty to obtain smooth regular/even finish using sand paper and applying two coats of exterior acrylic emulsion (weather proof treatment) over one coat of primer, complete all as specified and as directed ( The tint and shade be as approved by the GE) Note:- The treatment shall be carried out by the authorised applicator of the firm complete all as specified and directed.

Supply only Liquid water proofing compound complete all as specified and directed

M&L for repairing the edge/corner of chajja/roof projection and similar work by removing of plastered width/girth exceeding 15cm & n.exc 30cm and making good with 15cm rendering in cment mortar 1:3 to match with including chicken wiremesh netting on exisiting surfaces including necessary form work complete all as specified and directed. (Note - Height of building upto G+2)

Dismantling Brick tiles or terracing tiles, single layer on roofs & removal of debries out side MOD land complete all as specified & directed (Work shall be carried out upto 2 storey bldg, contractor to quote rates accordingly)

M&L for plain cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate, (Average 50mm thickness) in roof for padding to achieve the 1:40 slope complete all as specified and directed.

M&L for 10mm thick rendering on concrete surface in CM 1:4 to be finished even and smooth with out using extra cement mixed with water proofing compound as per manufacturer instructions. Note:- WPC will be measured & paid separately.

Material and labour for water proofing treatment by applying one coat of oil base bituminous primer @ 0.3 Kg/Sqm with brush / roller, laying of 3 mm thick APP based polymer modified membrane reinforced non-woven polyester, weight not less than 3.50 Kg/Sqm and sealing all the over laps 100 mm in length side and 100 mm in width side of membranes laid with torch application including removing old existing water proofing treatment complete complete all as specified and directed. Note :- Work shall be carried out upto 2 storey bldg, contractor to quote rates accordingly

S&F cement concrete tiles 25cmx25cmx22mm thick, machine pressed; set jointed and pointed in neat cement slurry in roofs with grey cemnt and no pigment over and including 15 mm thick screed bed of CM 1:4 complete all as specified and as directed.

-ditto- as per item No 134 above but except tiles

M&L chipping / dismantling of loose damaged concrete removed carefully by using mechanical concrete upto good parent concrete to expose the existing reinforcement (direct hammering should be avoided) average thickness of chipping average 20 -70 mm alround lintel / beams / column upto 10 mtr height including scffolding complete all as specified and directed by EIC

Supplying and application of rust remover/converter (rebaklense RR of M/S fosroc chemicals India ltd or or equivalent as approved ) over the corroded reinforcement bar where ever/Polymer modified mortar micro concreting is required and cleaning the same after application incl cost of all materials, rent of tools, scaffolding, cost of brushes etc. upto 10 mtr height complete all as specified and directed by EIC

Providing and fixing shear key using 10 mm diameter TMT bars including drilling holes of 12 mm dia & 100 mm depth @ 300 mm spacing an all three sides of lintel/ beams and providing new TMT bars of same dia of reinforcement where as found reduced to less than 20% of original dia including tack welding and grout the holes of shere key with two component epoxy resion based anchoring grout master flow 935 of BASF/ LOK Fix p of fosroc by power gun complete all as specified and directed NOTE (i) Quoted rate is deemed to be inclusive of providing reinforcement & welding. (ii) The entire activities shall be followed as per manufqacturers instructions (iii) Quoted rate is deemed to be inclusive of all activities).

M & L for grouting of all RCC structure with Low viscous two parts of epoxy (Mixed in ratio as specified by manufacturer) Neofill LV by using preassure pump including drilling necessary holes of required size at distance of about 30 to 50 cm centre to centre as required , fixing of PVC Nozzles by quick setting ready made epoxy based plugging putty ,Scaffolding, and preassure grouting with compressor at about 1kgf to RCC beams/chajjas/slabs/columns at all heights as per manufactureres instruction and as directed by Eng- IN Charge.upto 10 mtr height Make of Low viscous epoxy shall be Neofill of M/s Fosroc/EPCO-KP-250+EPCO -250 of M/s Krishna conchem or equivalent of FOSROC, PIDILITE, HARIOM POLYMERS (P) LTD / SIKA NOTES: (i) Payment shall be made as per the weight of epoxy formulation as calculated based on net contained weight of epoxy actually consumed in the work. (ii) The sealed container shall first to be brought to the site and handed over to MES store and thereafter to be used as and when required in the presence of MES executive. (iii) Record of day to day consumption with location and date etc shall be maintained in the serially numbered certified bounded register with shall be signed by contractor and Enggr-in-Charge. (iv) The quoted rate is deemed to include the cost for sealing of cracks required for grouting purpose.

Supplying and application of nitobond EP (Manufactured by M/s Fosroc chemicals India Ltd , Krishna conchem or equivalent as approved, epoxy bonding agent over the old concrete surfaces including the cost of all materials, rent of tools, scaffolding, cost of paint, brush etc. upto 10 mtr height complete all as specified and directed.

M/L renderoc RG to repairs a damage RCC work and an average thickness of 20 to 70 mm thick for beam, column, and other RCC work flulid micro concrete shall be mixed with less than 6mm coarse stone aggregate and specified quantity of water mixed using a power operated slow speed stirrer and pouring. The work shall be carried out as per manufactures instructions, as per manufactures specification, testing as per manufactures instructions including the cost of all materials, rent of tools, scaffolding, form work and labour charges up to 10 mt height complete all as specified and directed (Make :- M/s Fosroc Chemical India Ltd, M/s choksey Chemicals, M/s STPL Ltd and Sika India Pvt Ltd)

M&L Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed..

M&L for providing and injecting chemical emulsion for Post constructional antitermite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25litres per linear metre including drilling and plugging holes etc in apron complete all as specified and directed.

M & L for mild steel TMT bars of 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders and binding with and including mild steel wire annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Preparing surfaces of wooden ends of posts, backs of chowkats, etc., and and treated with tar or coal tar black paint, area tarred exc 0.1 Sqm but n exc 0.5 Sqm each complete all as specified and directed.

M&L for treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc. area n.exc 0.1 Sqm each with tar or coal tar black paint complete all as specified and directed.

S&F 5.5mm thick sheet glass , ordinary quality and glazing with oil putty in square n. exc 0.50 m in each pane for windowes/ventlators complete all as specified and directed.

Supply only of SBR Latex of M/s Fosroc or equivalent complete all as specified and directed.

Use & Waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surfaces complete all as specified and directed.

Writing letters or figures (Block.Roman, Italic or Indian) n exc. 30 cm high shall be painted with thick paint, so that they stand out boldly and solidly without showing signs of brush marks, if necessary, they shall be repainted until the desired result is obtained all as directed.

Writing letters Stops, commas, short lines, dashes, hyphens, brackets, etc shall be painted with thick paint, so that they stand out boldly and solidly without showing signs of brush marks, if necessary, they shall be repainted until the desired result is obtained all as directed.

S&F corner glass self including bracket etc. Complete all as specified and directed. Make : Prayag Cat No. 1951

M&L Extra over cast iron pipe & fitting if lead joint isprovided in lieu of cement joint for CI pipes & fitting of dia 100 mm all as directed.

ditto- as per item here-in-before for 75 mm dia

M&L for Non skid, coloured ceremic tiles 7 to 8 mm thick (Square / rectanguler) polished area of each tile exceeding 0.11 sqm but not exeeding 0.18 sqm as in walls etc laid over and including 10 mm thick as in rendering layer in cement mortar 1:4, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for including removal of debries to outside MOD land complete all as specified and directed.

M&L for PCC (1:3:6) Type C2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed..

M & L for precast cement concrete (1:3:6) (using 20mm graded stone aggregate) solid building blocks exe 10 cm thick, in width (with plain or inter locking joints as directed) setting in CM 1:6 complete in wall or pillars complete all as specified and directed.

M&L for rendering 15mm thick on brick/stone/ PCC block masonry wall surface in cement mortar 1:4, finished even and smooth without using extra cement and using water proofing compound complete all as specified and directed.

M&L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends complete all as directed by EIC.

M&L PCC (1:2:4) type B0 using 12.5 mm graded aggregate as in coping including necessary formwork complete all as directed by EIC

Excavation in trenches, n.exc 1.5m wide and n.exc 1.5m deep and getting out in any type of soil complete all as specified and directed.

Demolition and breaking up drain pipes 150 mm dia (SGSW, AC or RCC hume pipe Class NP2 laid in trenches and jointed in cement mortar complete complete all as specified and directed.

M&L for PCC (1:3:6) type C2 ,40mm graded aggregate, as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid & tested for 150 mm bore for SGWG pipes complete all as directed.

Material and labour for reinforcement cement concrete pipes, 150mm bore, class NP2, laid and jointed complete with collars all as specified and as directed.

Returning filling including spreading, levelling, watering and well ramming in layers not exc 25 cm thick soft & loose soil complete all as directed.

Removing excavated material exc 250 m and n exc 500m and depositing where directed at a level n exc 1.5 m above the starting point complete all as directed

M&L for precast cement cocrete cover slabs (1:2:4) type B1 (20mm graded agg) set in CM 1:4 for man holes complete all as specified and directed.

M & L for 75 mm thick cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

M&L for Filling of dry Sand as in screed bed for PCC interlocking paver block including spreading leveling, and well ramming complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block of approved shape and size of 60 mm thickness, with minimum compressive strength of 35 N/Sqmm (M-35 grade), without correction factor for chamfering, made in rubber moulds with 0.50 mm thick scratch proof lacquer chemical coating on top surface, with grey cement and pigment complete all as specified and directed.

M&L Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including all nacessary excavation and earth work in any type of soil and making drainage opening wherever required complete all as specified and directed.

S&F GI tubing medium grade, ISI marked conforming to IS 1239 Part-I 2004, 20mm bore with and including all fittings such as bends, elbows, tees, short length, socket , union, check nuts, nipples etc. fixed and laid in trenches/floor/under culvert/road crossing etc including testing and including taking down old existing unserviceable tube complete all as specified and as directed.

S&F GI tubing medium grade, ISI marked conforming to IS 1239 Part-I 2004, 25mm bore with and including all fittings such as bends, elbows, tees, short length, socket , union, check nuts, nipples etc. fixed and laid in trenches/floor/under culvert/road crossing etc including testing and including taking down old existing unserviceable tubecomplete all as specified and as directed.

S&F GI tubing medium grade, ISI marked conforming to IS 1239 Part-I 2004, 40mm bore with and including all fittings such as bends, elbows, tees, short length, socket , union, check nuts, nipples etc. fixed and laid in trenches/floor/under culvert/road crossing etc including testing complete all as specified and as directed.

Supply and fixing of Gun Metal globe / Gate valve with iron wheel head, screwed both ends for iron pipe and fixed 20mm dia complete all as specified and as directed.

Supply and fixing of Gun Metal globe / Gate valve with iron wheel head, screwed both ends for iron pipe and fixed 25mm dia complete all as specified and as directed.

Supply and fixing of Gun Metal globe / Gate valve with iron wheel head, screwed both ends for iron pipe and fixed 40mm dia complete all as specified and as directed.

Taking down carefully (copper/aluminum) unsv point wiring complete of any type (batten/surface conduit or concealed) for light point, fan point, bell point ,socket point or power point including fixture and fitting such as switches , ceiling roses, pendants , regulators , sockets , light fitting etc. removing material to store for keeping in safe custody or for taking credit( credit for above items should be made as per conditions seperately) and making good the disturbed surfaces of wall/floor or ceiling to match with existing surface and finishing the surfaces with distemper/white washing/colour washing as per existing complete all as specified and directed.

Taking down carefully by unscrewing from main switch boards/cut out boxes/MCB DBs / complete sealing the cable end and making good disturbed surface by walls etc.

Taking down carefully by unscrewing from fitting and fixtures such as ceiling fittings,bulk head fittings, tube light fittings , building street light , flood LED lights etc all as specified and directed.

M & L for concealed Point wiring with PVC insulated and unsheathed multistranded Fire retardant low smoke( FRLS )copper conductor single core 1.5sqmm (nominal area) cable using approved colour code as per IS drawn through heavy duty rigid non metalic PVC conduit not less 20mm dia including all accesories like bend,tess,junction boxes etc with all accessories suitable for moduler type fitment including making arrangement for fixing of moduler flush boxes of suitable size complete along with copper earth wire PVC insulated & unsheated multitranded(FRLS)copper conductor cable of size 1.5sqmm as continous earth wire connected to common earth and erth dolly complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or froof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete all as specified and as directedbt Engr-in charge.

(a) One Light point /Fan point controlled by one switch

(b) One 3 pin socket outlet 5Amps on the same board with other switches

(c) One 3 pin 5 Amp socket out let controlled by one switch on independent board

(d) One bell /Buzzer point controlled by one bell push 5 amp on the same board with other switches or independent

(e) One light point controlled by two 2-way switch with cable 1.5 sqmm.

M & L for concealed Point wiring with PVC insulated and unsheathed multistranded Fire retardant low smoke( FRLS )copper conductor single core 2.5sqmm (nominal area) cable using approved colour code as per IS drawn through heavy duty rigid non metalic PVC conduit not less 20mm dia including all accesories like bend,tess,junction boxes etc with all accessories suitable for moduler type fitment including making arrangement for fixing of moduler flush boxes of suitable size complete along with copper earth wire PVC insulated & unsheated multitranded(FRLS)copper conductor cable of size 2.5sqmm as continous earth wire connected to common earth and erth dolly complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or froof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete all as specified and as directedbt Engr-in charge.

All as per item above but wiring with 4.0 Sqmm multi-stranded copper conductor PVC insulated, unsheathed fire retardant low smoke, cable and 4.0Sqmm multi-stranded copper conductor PVC insulated, unsheathed fire retardant low smoke, cable as continous earth wire connected to earth dolly for AC points complete all as specified and as directed..

M&L for Ceiling rose ceiling rose , 2 to 3 terminal PVC/ polucarbonate , isolated body type suitable for AC 230volts complete all as specified and as directed.

M & L for module cover plate with frame as per site requirement for 1 module complete all as specified and as directed.

M & L for module cover plate with frame as per site requirement for 2 module complete all as specified and as directed.

M & L for module cover plate with frame as per site requirement for 3 module complete all as specified and as directed.

M & L for module cover plate with frame as per site requirement for 4 module complete all as specified and as directed.

M & L for module cover plate with frame as per site requirement for 6 module complete all as specified and as directed.

M & L for module cover plate with frame as per site requirement for 8 module complete all as specified and as directed.

M & L for 1/2 Modular metal Flush box as per site requirement complete all as specified and as directed.

M & L for 3 Modular metal Flush box as per site requirement complete all as specified and as directed.

M & L for 4 Modular metal Flush box as per site requirement complete all as specified and as directed.

M & L for 6/8 Modular metal Flush box as per site requirement complete all as specified and as directed.

M & L for modular switch 1 way 6 Amp 1 Module complete all as specified and as directed.

M & L for Modular switch 2 way 6A , 1 Module complete all as specified and as directed.

M &L for Modular Socket 6A 2/3 Pin universal 2 module complete all as specified and as directed.

M & L for Modular Switch 1 way 16/20 Amp 1 Module complete all as specified and as directed.

M &L for Modular Socket 16A/ 6A 2/3 Pin combined 2 module complete all as specified and as directed.

M &L for Modular fan step regulator 100 watt 2 module complete all as specified and as directed.

M & L for Modular Bell push 6A1 way, 1 Module complete all as specified and as directed.

Supply and fix of Lamp holder, white Polycarbonate body, with back plate suitable for batten fittings fixed in position & connecting complete all as specified and as directed.

Supply and fix of Bell musical type AC 230 Volts, as directed including connecting complete all as specified and as directed.

S & F industrial type plug & socket board SP & N enclosure with 2 pole and earth metal plug & socket complete with 20 Amp MCB SP complete all as specified and as directed.

S&F energy efficient LED tube light fitting integrated batten type with built in LED Chip & integral LED driver 21 watt, channel housing & diffuser of length 1200 mm (approx.) with all accessories, fixing arrangement internally pre-wired, fixed in position & connecting complete all as specified and directed.

S&F energy efficient LED tube light fitting integrated batten type with built in LED Chip & integral LED driver 10 watt, channel housing & diffuser of length 600 mm (approx.) with all accessories, fixing arrangement internally pre-wired, fixed in position & connecting complete all as specified and directed.

S & F bulkhead fitting 10watt made die cast aluminium housing with complete assembly and PC opal diffuser suitable for surface/wall mounted dust and water resistant complete all as specified and as directed .

Supply and fix of LED lamp 9 watt complete all as specified and directed.

Taking down carefully (copper/aluminium ) submain wiring complete of any type (batten/surface conduit or concealed ) for socket point or power point complete with all fittings such as swiches sockets pendants etc complete and making good distuebed surface of wall,floor or ceiling with plaster of tiles or roof treatment etc and finishing the surface with distemper white washing/co0lour washing to match with the existing surface complte all as specified and directed

M&L Sub main wiring using PVC insulated and unsheathed multistranded two single core PVC insulated FRLS cable 4 sqmm copper conductor multi stranded and one 4.0 sqmm copper conductor insulated cable using as earth wire approved colour code as per IS drawing in and incl 20mm PVC conduit with all accessories and making good disturbed surfaces of wall, floor or ceiling with plaster and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete as specified and as directed NOTE:- 2 runs of 4sqmm copper cable & 1 run of 4.0sqmm copper cable in and including 20mm PVC conduit shall be measured as one unit

M & L for distribution board (DB), double door (CRCA sheet) dust and vermin proof SPN 8 way with 100 Amps rated copper busbar, neutral bar, earth bar and cable ties for cable management,reversible door for for IP 43 , single pole and neutral 250 Volts, flush to wall complete with IP 43 protection complete all as specified and directed.

M & L for distribution board (DB), double door type, as per IEC 61439-3 made out of sheet metal enclosure (CRCA sheet) dust and vermin proof MCB DB, TPN 4 way with 250 Amps rated copper busbar, 415 Volts with in built MCCB 160 Amps, 10 KA, 01 ,new MCB SPN 32 Amp, 10KA -04Nos, MCB SPN 63Amp -04 Nos.,2neutral bar and 2 earth bar IP 43 protection,cable ties for cable management(Fully insulated busbar and shrouded neutral bars),reversible door for IP 43 ,flush mounted to wall complete all as specified and directed. Note : Rates are inclusive for flush(Concealed ) mounted of DB, MCCB 160Amp TPN ,MCB SPN 32Amp and 63Amp.

M&L for MCB single pole & neutral 240 volt C curve 10 KA (32 to63)Amps capacity IP 20 complete all as specified and directed

M&L for MCB single pole,5 to 30 Amp 240 volt B curve 10 KA, IP 20 complete all as specified and directed

S&F building security LED Light fitting 35 watt, system efficiency not less than 100 lumen / watt, IP66 protection, consisting of high / low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with weather proof gasket for lamp & driver compartment, Heat resistance toughened glass fitted in cast aluminium housing with SS screws, fixed on existing bracket & connecting including taking down old light fitting of any description complete all as specified and directed.

Earthing comple with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised earth lead wire mm as 4.0mm dia by means of bolts nuts check nuts and washers of galvanised iron or steel all as shown in electrical plate no.3 including earth pit in PCC concrete 1:2:4 type B-1,Cast iron cover 10 MM THICK HINGED to CI frame ,excavation and earth work in any type of soil and including protection pipe 15mm dia and water pipe GI tubing 20mm light grade with funnel and wire mesh connected to earthing test point complete all as specified and directed by Engr-in-ChargeNote:(i)Rates are inclusive of 7.5m long GI earth wire 4.0mm dia (ii)Rates of CI frame,RCC Pit cover,funnel and wire mesh included in the cost of item.

Supply and fixing Heavy duty Exhaust fans, AC single phase , 230/240 volts, 50 Hz, Metalic body 300mm sweep, 1400 RPM with louvers, fixing with 4 nos hold fastener nut and bolt with washer and connecting with flexible PVC insulated multistranded copper conductor cable of size 0.75 sqmm from ceiling rose to exhaust fan including civil work for making opening on wall of suitable size for installation of exhaust fan and making good all as specified.

Supply and fix Exhaust fan AC single phase voltage 230V, 50 Hz, 1200 RPM, 250 mm sweep plastic body complete with louvers shutter, Copper winding of sweep 250mm (Note: Making of hole for fixing of exhaust fan in stone machinery bldg/ aluminium window) complete all as specified and directed

S & F energy efficient BLDC Ceiling Fan, 1200mm sweep BEE 5 star rated, AC single phase, 230 volts, 50 Hz, and connecting up including provision of three core flexible copper wire of size 1.5 sqmm from ceiling rose to ceiling fan complete in all respect and all accessories complete all as specified and directed. including taking down old unsv, all as per site requirement.

Supply & Fixing 5 star rated electric storage water heater (vertical type) 25 Ltr, 230 V, AC, Single phase power input 2000w,standing loss in kWh 24 (hours) 45 °C 0.511 kWh with and including connecting fastners nuts not less than 100 mm with suitable nut, bolt & washers grouted in walls with complete masonary work for proper mounting of Geyser fastning bolts etc as directed as site reqmt and making necessary inlet and outlet water connection as well as electric connection including testing on load for entire satisfaction of Engineer-in-Charge complete all as specified and directed.

NOTE: Amount of credit of Rs. 386860.63 for retrieved materials is mentioned in schedule of credit on Srl Page No. 37 of tender documents in pdf form which will be deducted offline while acceptance of tender.

Sukhi Electricals

EVEREST BUILDERS

M/s Bombay Novelty Stores

VINUBHAI P. CHANDRA

Vijay Construction Co