CWE KOTA/ALW-41 OF 2020-21 SPECIAL REPAIR TO BUILDING NO. P-275 AT ITARANA CANTT ALWAR

Amount

B/R ITEMS Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars & precast concrete mosonry etc. and removal all rubbish material complete all as specified directed.

Taking down cement or cement lime plaster any description, on brick or stone walls, etc. including raking out joints, hacking for key & scrubbing down with water, etc. & removing rubbish off the premises, complete all as directed.

Dismantling of stone slabs and tiles of any descirption or thickness in floors, aprons etc. laid bedded and pointed in any CM etc. complete all as specified and directed.

Dismatling boarding any descirption (board/playwood) fixed in any position with nails, complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding frames truss etc. complete all as specified nad directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level and removal all rubbish material complete all as directed..

Demolition of reinforced cement concrete of any description and in any position mortar including all quions, pillats etc. complete all as specified and directed.

Dismantling of cement concrete tiles in floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning for refixing or removal complete all as specified and directed :-

15mm bore.

20mm bore.

Demolition of existing lime concrete/ PCC padding, roof treatment of any thickness laid over RCC roof/ Chajjas etc removing complete layer of bitumen under concrete/PCC padding, cleaning and washing of roof with water to remove dust etc as preparation to receive treatement, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from frame)n exc 1.5 sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from frame) exc 1.5 Sqm but n exc 4 Sqm each complete all as specified and directed.

Taking down shutters of any description exc. 2 sqm each complete all as specified and directed.

Taking down shutters and refixing in different opening exc. 1 sqm and n exc 2 sqm each complete all as specified and directed.

Taking down shutters of any description exc. 2 sqm & n exc 2 sqm each complete all as specified and directed.

Taking down shutters and reifixng in same opneing exc 1 sqm and n exc 2 sqm each complete all as specified and directed.

Resecuring or easing & adjsuting of shutter exc 1 sqm and n exc 2 sqm each, complete all as specified and directed.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides etc complete and size of member of shutters as specified in SSR Part-I (2009) section 8 all complete all as specified and directed.

Dismantling water tank of capacity exceeding 250 Ltrs but not exceeding 500 Ltrs and removal from site complete all as specified and directed .

Dismantling water tank of capacity exceeding 500 Ltrs but not exceeding 1000 Ltrs and removal from site complete all as specified and directed .

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,Manholes, pier holes, laying ofcables, pipes etc. n exc 10 sq m on plan and n exc1.5 m in depth and getting out in soft/ loose soil, complete, all as specified & directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick,complete, all as specified & directed.

Removal of excavated surplus spoil to a distance n.exc 50m and depositing where directed at level not exceeding 1.5 m above the starting point,complete, all as specified and directed .

M & L for cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as in plinth protection 75 mm thick laid in bays and surfaces finished even and fair, including filling the joints with bitumen mastic complete all as specified and directed

M & L for PCC 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) as in cills, coping steps, tank staging, sesmic and other similar courses, lacing courses parapet and railing upto 60cm height kneeler kerb and alike including weathering, slightly rounded or chemfered angle and throating, finished even and fair, complete all as specified and directed.

M & L for 75mm thick PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base of floor/roof/pavings/path etc finished even and fair surface complete all as directed.

M & L for PCC 1:4:8 type D-2 using 40mm stone aggregate as in foundation concrete complete all as specified and directed.

M & L for PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate as in padding and levelling coarse on roof and floor complete all as specified and directed.

M & L for providing Precast cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in ladings, cover slabs (for manholes etc) chajjas, water troughs, managers, shelves and similar article with plain faces, complete all as specified and directed.

M & L for cutting holes into stone walls built in cement mortar or in cement lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 not exc. half brick complete all as directed.

Racking out joints/pointing to random rubble or polygonal rubble uncoursed or brought up to courses built in cement or cement lime mortar complete all as specified and directed.

M & L for 40mm thick cement concrete type B-1 using 20mm graded crushed aggregate laid in panels using glass dividing strips, finished even and smooth without using extra cement, complete all as specified and directed.

M & L for providing cement concrete (1:2:4) type B-1 using 12.5mm graded stone aggregate as in padding and levelling coarse of floors and roof complete all as specified and directed.

M&L for cutting into existing manholes for conecting new 150mm internal dia drain pipe, making good pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 as in ceiling and finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on other than fair face of brick masonry surface or on stone masonry surfaces finished even and smooth without using extra cement mixed with liquid water proofing admixture as per manufacturer instructions, complete all as specified and directed. Note:- Liquid water proofing admixture shall be measured and paid separately.

Supply only liquid water proofing admixture complete all as specified and directed.

M & L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping, 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and directed.

M & L for preparing newly plastered surfaces of walls and applying three coats of white wash on walls, complete all as specified and directed.

M & L for preparation old surfaces of walls and applying two coats of cement paint, complete all as specified and directed.

M & L for preparing newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M & L for preparing old plastered or unplastered ceiling surfaces and applying two coats of white wash complete all as specified and directed.

S&F for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L preparation old steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint of 1st grade quality complete all as specified and directed.

M & L for preparation of new or previously untreated wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved shade over one coat of pink primer complete all as specified and directed.

M&L preparation old wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of 1st grade quality complete all as specified and directed.

M & L for preparation of new plastered surfaces of walls and applying two coats of acrylic emulsion paint (exterior grade) of approved shade/tint over a coat of primer, complete all as specified and directed.

M & L for preparing of newly plastered surfaces and applying two coats of oil emulsion distempering (OBD) over and including a coat of white wall care putty 2mm thick over a coat of primer on walls, complete all as specified and directed.

M&L for complete removal of existing treatment on walls, chajjas etc including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying and applying two coats of acrylic emulsion paint (Exterior grade) complete all as specified and directed.

M&L for complete removal of existing treatment on walls, chajjas etc including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying and applying two coats of cement base paint over a coat of white wash complete all as specified and directed.

M & L Rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement, complete all as specified and directed.

M&L 300x450x7-8mm thick joint free glazed ceramic coloured tiles as in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including 10mm thick rendering in cement sand mortar 1:3 complete all as specified and directed.

M & L for vitrified ceramic tiles dark shade/double charged/ultra charged) 10mm thick (square/rectangular) area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm joint free as in floors and including 10mm thick screed bed in CM 1:3 laid on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M & L for vitrified ceramic tiles dark shade/double charged/ultra charged) 10mm thick (square/rectangular) polished area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm joint free as in floors and including 10mm thick screed bed in CM 1:4 laid on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M & L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors and including 10mm thick screed bed in CM 1:4 laid on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M & L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm joint free as in floors and including 10mm thick screed bed in CM 1:4 laid on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M & L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors and including 15mm thick screed bed in CM 1:6 laid on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M & L Rounding to edges of stone slabs one edge, such as in steps,cooking platform, and other similar situations complete all as specified and directed.

S &F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with mild steel square tube fixing in opening complete all as per specifications and drawings as applicable to item 08095 given in SSR Part – II (2010).

S & F in repairs 110mm stack clamp out of 50mmx5mm flat iron and 16mm dia round iron stays incl bolts and nuts and securing end of stays to walls or roof etc. complete all as specified and directed.

S & F for 75mm thick steel fibre reinforced (SFRC) manhole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS-12592 BIS standard minimum load bearing capacity 5 ton/sqm, in square, rectangular or circular shape complete all as specified and directed.

M & L in reparis salt glazed stone ware gully trap square or round mouthed type 'P' of size 150 x 150 mm with CI grating, setting & jointing with cement with grouting surrounding gully trap with PCC 1:3:6, type C1 block 30x30x45cm together with necessary form work, excavation & earth work in soft/loose soil, complete, all as specified and as directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6 metre mean radius built in cement mortar (1:4), complete, all as specified & directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) with width equal to the length of the brick laid dry & flat abutted with each other with gap between adjacent bricks not exc. 10mm over UG cable for protection complete all as specified and directed.

M & L for brick work with FLY ASH BRICKS straight or curved on plan exc 6 mean radius, built in CM 1:6 complete, all as specified & directed.

M&L for dry sand and punning for cushioning to under ground cable complete all as specified and directed. Note : For the purpose of payment only punned thickness shall be measured.

M & L for machine cut Kota stone slab 20 to 25 mmthick as in floor, cooking platform, treads etc laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including cement screed base (bedding layer) of 20mm thick in CM 1:6 for laying floor finishes complete all as specified and directed. Note:- Size of Kota Stone slab not less than 550mm x 550mm.

M & L for 20-25mm thick machine cut Kota stone as in riser such as steps, skirting, dado and pillar set etc over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including10mm thick cement plaster in CM (1:3) on other than fair faces of brick work or stone surfaces of walls complete all as specified and directed.

M & L for machine cut Kota stone slab 20 to 25mm thick as in shelves & similar works in single piece not exc. 1.50m in length, front edge to be half moulded complete, fixed & jointed with grey cement set and pointed in cement mortar 1:4 including rubbing and mirror polishing (top side only and bottom side shall be self finished only), including cutting chases as required and making good to filling as original in cement mortar 1:4 for inserting stone slab shelves in stone/brick walls complete all as specified and directed.

M&L 20-25mm thick granite slab/tiles (of any type table rubbed and polished) in steps, jambs pillars, window cills, cooking platforms and like set in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite over screed bed or bedding layer 15mm thick in CM 1:3 for laying floor finishes complete all as specified and directed.

M & L for machine cut 20-25mm thick Green Marble stone slab in single piece as in shelves, steps (i.e. riser/treads) cills, etc. and similar works laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including ball nosing of exposed over 15mm screed in CM 1:6 edges and including dismantling old stone slabs complete all as specified and directed.

S&F steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed for following sizes:-

15mm bore.

20mm bore.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floor etc ) complete all as specified and directed for following bore:- Note : Old serviceable water tubing retrieved from taking down here-in-before shall be used. The quoted rate shall deemed to include new GI fittings (ISI marked). Old fittings shall not be used.

15mm bore.

20mm bore.

S & F in repair 15 mm bore angle stop valve of copper alloy, fancy type, chromium plated screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S & F in repair 20 mm bore angle stop valve of copper alloy, fancy type, chromium plated screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S & F in repair 15 mm bore concealed type stop valve of copper alloy, fancy type, chromium plated screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S & F UPVC (SWR) pipes nominal outside diameter (Type B with wall thickness 3.20 to 3.8mm) single socketed in any length rubber ring joints laid in trenches or in floors of pipes including taking out old unserviceable PVC/CI pipes complete all as specified and directed for the following sizes:-

75mm bore.

110mm bore.

S & F UPVC (SWR) pipes (Type B with wall thickness 3.20 to 3.8mm) single socketed in any length including taking out old unserviceable PVC/CI pipes complete all as specified and directed for the following sizes:-

75mm bore.

110mm bore.

S&F UPVC (SWR) bends any radius complete all as directed for the following sizes:-

75mm bore.

110mm bore.

S&F UPVC (SWR) bends any radius with access door complete all as directed for the following sizes:-

75mm bore.

110mm bore.

S&F UPVC (SWR) branch piece, single (Y) equal or unequal with access foor complete all as directed for the following sizes:-

75mm bore.

110mm bore.

S&F UPVC (SWR) branch piece, of Single (T) equal or unequal with access foor complete all as directed for the following sizes:-

75mm bore.

110mm bore.

S&F UPVC (SWR) branch piece, of Double (T) equal or unequal with access foor complete all as directed for the following sizes:-

75mm bore.

110mm bore.

S & F PVC (SWR) vent cowl for 110 mm bore of pipe complete all as specified and directed.

S & F PVC (SWR) floor trap, plain with grating including jointing with solvent cement dia of outlet 75 mm bore complete all as directed.

S&F in repairs vitreous China squatting pan, Orissa pattern, size 580mm x 440mm white with integral foot rests and 'P' or 'S' trap, including provision of cement concrete bedding, connection to trap and flushing pipe etc. complete including making good to disturbed surfaces of floor to match with existing specifications complete all as specified and directed .

S&F in repairs PVC low level flushing cistern10 litre capacity with intel ball valve float & handle, syphonic action type including brackets & flush pipe of polythylene of low or high density or PVC 32mm dia for LLFC fixed complete all as specified and directed .

S & F in repair ball valve high pressure with polythene float and fly nut screwed on iron pipe suitable for 20mm bore pipe (minimum weight -210Gm) with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

S & F for mild steel cupboard shutter with frame, Godrej Pattern, made out of 22 guage mild steel sheet including chromium plated MS handle with proper locking arrangment (brass mortice lock, vertical type, size 65mm, 4 Lever with escutcheon plates & two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with 06 Nos 12mm dia bolt 150mm long grouted in brick wall/concrete including making good the distrubed sufaces as original complete all as directed. Note : The measurment shall be taken of from elevation and not girthwise."

S & F factory made steel windows with side hung shutters including box type hinges with steel handles & steel pag stay complete (without glazing bars), dovetailed or welded including fixing of lugs in PCC 1:2:4, type B-1, using 20mm graded stone aggregate & making good walls & cills to match the existing and including one coat of red oxide/ zinc chrome primer complete all as specified and directed.

S & F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks galvanised stainless steel wire staples complete all as directed.

S & F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanized wire staples complete all as specified and directed.

S & F 38mmm thick glass dividing strips, 3mm thick and inserted in position to conform to design, complete all as specified and directed.

S & F in repair for sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed on wall with PVC rawl & cadmium plated brass screwes complete all specified and as directed.

S & F Rajshri Brand factory made PVC shutter of 18mm thickness consisting of panel of 18mm thick cellucaply of density 600 kg, cbm density with prelaminated sheet on one side cut in desired size of shutter and fixed with frame as in cabinet boxes with shelf and shutter and fixed with frame as in cabinet boxes with shelf and shutter full size fitted under orabove the kitchen cooking platform and/or other platform including all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc. including dismantling boarding any description, fixed in any position with nails complete all as specified and directed. Note:- Items like cupboard knobs, stainless steel channel, CP plate clip hinges are included in the mentioned rates and as per manufacturers specification and drawings. he measured area shall be front elevation.

M & L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

S & F flat iron as in hold fast welded to angle iron door/ window frames complete all as specified and directed.

S&F for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L 35mm thick factory made 2nd class glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. The shutter shall be fitted to the chowkhats as directed

S&F 35mm thick factory made IInd Class Hard wood plain framed, panelled shutter(two panel) with lock rail and panel of 9mm B.W.P. commercial ply seasoned & chemically pressure treated /12mm thick particle board veneered with commercial veneering on both faces. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S & F 100mm mild steel butt hinges medium weight colled rolled ISI marked complete all as specified and directed.

S & F 100mm exctruted Butt hinges aluminium allot with galvanised mild steel hing pin complete all as specified and directed.

S & F 100mm long aluminium anodised barrel tower bolt of extruded section and fixed, complete all as specified and directed.

S & F 200mm long aluminium anodised barrel tower bolt of extruded section and fixed, complete all as specified and directed.

S&F 125mm size aluminium handle, fabricated type anodised complete all as specified and directed.

S & F 300mm ordinary rat tail pattern springs including roller and roller palte complete all as specified and directed.

S&F 75mm dia Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate & fixed with screws, complete all as specified and directed.

S & F contineous piano hinges mild steel bright finish or electro galvanised width of flaps (when opened) 30mm, complete all as specified and directed.

S & F Brass magic eye for door shutter etc. complete all as specified and directed.

S & F Ball catches with 8mm dia steel ball and brass body and striking plate including letting in etc. complete all as specified and directed.

S&F 300mm long mild steel sliding door bolts with hasp & staples type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, 04 on bolt plate and 02 on staple plate and fix complete all as specified and directed.

S&F 140mm long floor door stopper of aluminium alloy body and tongue, annodised, with hard drawn steel spring fixed in floor complete all as directed.

S&F 32mm GI Pipe 500mm long as in spout pipe from sunken floor to external surfaces includuing cutting brick wall/RCC/PCC and making good in CM 1:3 pipe complete all as specified and directed.

S & F in repairs stainless steel kitchen plate rack of size 900mm x 750mm x 230mm fabricated out of Ist quality 1.00mm thick stainless steel sheet with partition for small/large plates made out of 24 gauge thick stainless steel sheet all as per sample kept in GE office and hanged on wall by the help of steel screws grouted in walls with rawl plug complete all as specified and directed.

M & L screed bed or bedding layer of on fair faces of concrete/ brick surfaces , 10 mm thick, in cement mortar 1:4, mixed with water proofing compound 3% by wt of cement finished even and smooth in order to maintain proper slope over existing roof surfaces for laying APP based polymeric membrane finished complete complete all as specified and directed. Note : Polymeric membrane and Water proofing compound shall be measured and paid separately under respective item of BOQ.

M & L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

Supply fabrication and fixing powder coated (Thickness of powder coating not less than 50 micron) aluminium windows and ventilator shutters, side hung type without sash bars, aluminium section weighing 0.55 Kg/RM including necessary jointing cleats, glazing clips, rubber neoprene packing, powder coated anodised aluminium snap beading, screws, powder coated anodised aluminium fittings such as peg stays 150mm long (01 No. for each leaf), Butt hinges type B-21 100mm size (02 Nos for each leaf) & handle (01 No for each leaf) etc complete all as specified and directed. (Note :- Glazing/wire mesh shall be measured and paid separately under respective items of Schedule.

S & F anodised aluminium powder coated (any colour) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S & F in repairs harrison rails, mild steel, chromium plated curtain rod with fixing bracket, stops, rollers etc. complete all as specified and directed.

S & F 50mm thick sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc n exc. 2 m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4 complete all as specified and directed.

S & F in repairs stainless steel drapery rod of 25 mm inner dia (in lengths as directed) of approved colour with and including decorative finial at both ends and pair of stainless steel brackets fixed at both ends with PVC rawl plug and steel screws on walls/beam, including PVC curtain rings of matching colour @ 10 cm C/C complete all as directed.

S&F rotational moulded polythylene water tanks triple layers (Cylindrical vertical with closed top) of any capacity and fixed in same position capacity of tank in 500 Ltrs and including all necessary fittings complete all as specified and directed.

S&F rotational moulded polythylene water tanks triple layers (Cylindrical vertical with closed top) of any capacity and fixed in same position capacity of tank in 1000 Ltrs and including all necessary fittings complete all as specified and directed.

M&L for laying 60mm thickness machine pressed precast concrete interlocking paver block with any shape and size confirming to IS 15658-2006 M-35 grade grey cement and no pigment laid over sand cushinong and including 25cm thick sand cushioning complete all as specified & directed.

Supply and fix treatment for roof portion APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.5 Kg/Sqm of make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufactured by M/S IWL Ltd or ‘Shaliplas’ (polyester) manufactured by M/S Capital Steels and chemicals Pvt Ltd as approved by GE, black finish reinforced with non-woven polyester matt (weighing not less than 150 gm/Sqm), with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or ‘EMW FLATE’ of M/S Texas India Ltd} at the rate of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and as directed. Note :- (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of bituminous primer confirming to IS-3384 applied @ 0.40 Kg/Sqm. (ii) Polymeric membrane shall be taken to a height of 60cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm(minimuim) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimeny/other vertical surfaces and polimeric membrane insterted in groove and sealed with paving bitumen. (v) Exposed surfaces of APP membrane shall be applied with one coat of bituminous aluminium paint @ 150 ml/Sqm. (vi) Above aspects are deemed to be included in quoted rate.

M & L for water proofing treatment in sunken floors as described hereunder:- (i) Provide 50mm thick PCC 1:1.5:3 type A-0 using 10/12.5 mm graded stone aggregates laid over slab of sunken floor after applying cement slurry for filling undulations finished fair and even without using extra cement (i) Sunken floor and sides upto finished floor level shall be plastered with 15mm thick cement plaster in mortar 1:4 mixed with water proofing compound @ 3% by weight of cement. (ii) Preaparing plastered surfaces and providing APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm of make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufactured by M/S IWL Ltd or ‘Shaliplas’ (polyester) manufactured by M/S Capital Steels and chemicals Pvt Ltd or Hydro Stop manufactured by TIKITAR DANOSA (INDIA) Pvt Ltd as approved by GE, black finish reinforced with non-woven polyester matt, (weight not less than 150 gms/sqm) with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or ‘EMW FLATE’ of M/S Texas India Ltd} at the rate of 0.40 Ltr/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and the joints sealed properly all as per manufacturer’s instructions, and providing a cushion layer of coarse sand of thickness 25mm to protect polymeric membrance complete all as specified and as directed. Note: (i) Polymeric membrane shall be laid in sunken floor and on sides upto finished floor level (ii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iii) Above aspects are deemed to be included in quoted rate. (iv) Supply only water proofing compound shall be measured and paid separatgely).

S&F in repairs swivel shower rose fancy type chromium plated 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S & F in repairs chromium plated brass toilet paper holder, complete all as specified and directed.

S & F in repairs brass chromium plated brass jet assembly for EWC with PVC connection as required, complete all as specified and directed.

S & F in repairs brass chromium plated towel ring including a pair of CP brass bracket, complete all as specified and directed.

S & F in repairs brass chromium plated soap dish, complete all as specified and directed.

S & F Mirror Cabinet (PTMT) fixed on wall with chromium plated brass screws, complete all as specified and directed. Make:- Cat Part No. 551 of PRAYAG or equivalent as specified in Appendix 'D'.

S & F 125mm size Grating Doom of chromium plated (Minimum weight 120 gms) complete all as specified and directed.

S & F in repairs 32mm dia PVC flexible waste pipe for WHB/Sink 600mm long with PVC coupling complete all as specified and directed.

S & F in repairs for sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 915mm x 460 mm with bowl size 410mm x 330mm x160 mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, all as specified and as directed.

S & F in repairs white Vitreous china wash down water closet pan (EWC) white (ISI marked) inclduing connection to drain (OR outgoing pipe) and to flushing pipe antisyphonage pipe etc. & with plastic WC seat cover (white) closed pattern complete all as specified and directed.

S & F vitreous china wash basin with Pedestal , white, flat back, size 550 x 400 mm including one no 15mm bore fancy type pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered HOT or COLD with long screwed shanks and fly nuts, screwed for iron pipe, one No PVC waste pipe 25 mm dia and 75 cm long with 32 mm dia connector, 32mm size waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange end, bedded in red lead cement and other fixed and PVC connection 15 mm dia & 600mm long with two Nos check nut and washer complete including cutting for and pinning in ends of bracket or erecting stand complete all as specified and directed

S & F in repairs brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed, compelte all as specified and directed.

S & F in repairs 300mm tuffened corner acrylic shelf 6mm thick with brass chromium plated guard and fixing arrangements complete all as specified and directed.

S & F Hand Shower (Health Faucet) with 8mm dia 1 metre long flexible tube with wall hook for EWC complete all as specified and as directed.

S&F in repair 15mm dia bib tap cast copper alloy fancy type crutch or butter fly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair 15mm dia bib tap cast copper alloy fancy type half turn with wall flange chromium plated with capstan head screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F brass CP wall mixer 3 in 1 with L-Bend mixing hot & cold water screwed down for iron pipe and fixed in repairs,complete all as specified and directed.

S & F Factory made solid PVC moulded door shutter, 28 to 30 mm thick (style), with 2, 4 or 6 raised panel design with 2mm thick moulded prelaminated PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face, supplying and fixing in frame at site as all as per specifications and drawings as applicable to item 08101 given in SSR Part – II.

E/M ITEMS Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including teak wood battens/PVC casing caping and making good disturbed surfaces of walls, floors & ceiling etc.including dismentling of fittings to match with existing surfaces, complete all as specified and directed.

M & L for point wiring complete with 1.5 Sqmm single core unsheathed stranded copper conductor cable of 1100 volts grade PVC insulated and unsheathed FRLS cable enclosed in and including PVC casing and capping not less than 20mm width with MS sheet metal sunken switch/terminal box 1.2mm thick and phenolic laminated sheet cover 3.0mm thick and brass screws with cup washers with all necessary wall cutting and making good distrubted surface as directed, including all necessay wall cutting and making good disturbed surface including 1.5 Sq.mm solid copper conductor with green PVC FRLS insulated unsheathed earth continuity conductor to common earth & connecting to earth dolly for the following :-

One fan point controlled by one, one way switch

One fan point controlled by one switch and regulator.

One bell/buzzer pointcontrolled two way switch

One light point controlled by two, two way switch

One 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

One 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per description of serial item No. 126.00 here-in-before but for one 3 pin socket outlet 15 Amps with 2.50 sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continous earth wire in green colour complete all as specified and directed.

S & F switch piano flush type 5/6 Amps single pole one way 230 volts complete all as specified and directed.

S & F switch piano flush type 5 Amps single pole two way 230 volts complete all as specified and directed.

S & F switch piano flush type 15 Amps single pole one way 230 volts complete all as specified and directed.

S & F, socket outlet 3 pin(with 2 pin outlet also), 5/6 Amp flush type, 240 volts all as specified & directed.

S&F socket outlet two-in-one, 3 pin, 5 Amp and 15 Amp, flush type , 240 Volt complete all as specified & directed.

S & F bell push flush type 5 Amps, 240 Volts, complete all as specified and directed.

S & F bell /buzzer AC 230 Volts, single pole complete all as specified and directed.

S & F ceiling rose surface bakelite 65x50mm with two or three terminal complete all as specified and directed.

S&F in repairs decorative ultra slim liner LED lighting fixture with extended poly carbonate environmental friendly, energy efficient suitable for 16W to 20W with LED tube of model E-LITE LED pride and connecting up with the fitting from ceiling rose/connector using copper flexible cord of size 1.5sqmm, 3 core of suitable length complete all as specified and directed. Make :- Havelles Cat Part No LHEXBHP71N1W018 or equivalent of Philips/Cromption Greaves/Bajaj/Wipro/GE.

S&Fin repair decorative ultra slim liner LED lighting fixture with extended poly carbonate environmental friendly, energy efficient suitable for 8/9 W to 20W with LED tube of model E-LITE LED pride and connecting up with the fitting from ceiling rose/connector using copper flexible cord of size 1.5sqmm, 3 core of suitable length complete all as specified and directed. Make :- Havelles Cat Part No LHEXBLP71N1W009 or equivalent of Philips/Cromption Greaves/Bajaj/Wipro/GE.

S & F for lamp holder, PVC/polycarbonate type with back plate suitable for battern fittings complete all as specified and directed.

Supply and fixing Adore LED lamps of 9/10 Watt and including taking down old u/s CFL lamp complete all as specified and directed. Make - Cat Part No LHLDERHEML8X010 of make Havells or equivalent model of make Philips/Cromptom/ Greaves/Wipro/ Bajaj

Supply & Fixing of stepped type electronic fan regulator flush type and connecting up , ISI marked , 240 Volts complete all as specified and directed.

S & F sheet metal enclosure double door DB SPN 8 way, 240 volts protection class IP-43 made out of CRCA mild steel sheet surface with epoxy powder coated surface confirming to IS-13032, IS 8623, BS-5484 with tinned copper bus bar of 200 Amps capacity all as specified and directed.

S & F sheet metal enclosure double door DB SPN 4 way, 240 volts protection class IP-43 made out of CRCA mild steel sheet surface with epoxy powder coated surface confirming to IS-13032, IS 8623, BS-5484 with tinned copper bus bar of 200 Amps capacity all as specified and directed.

S & F MCB SPN 32 Amps, 240 volts, B-curve, rupturing capacity 10KA conforming to IEC-60898, Part-I, complete, all as specified & directed.

S & F MCB SP 6 to 32 Amps, 240 volts, B-curve, rupturing capacity 10KA conforming to IEC-60898, Part-I complete, all as specified & directed.

S & F MCB SP 63 Amps, 240 volts, B-curve, rupturing capacity 10KA conforming to IEC-60898, Part-I complete, all as specified & directed.

S & F for submain wiring with 2 single core PVC insulated & PVC unsheathed FRLS cable 1100 Volt grade with 06 Sqmm copper multistranded conductor drawn through and including PVC conduit/casing-caping fixed on surface to wall/ ceiling by means of MS screws and saddles including one run of 6 Sqmm single core multistranded copper conductor 1100 volts grade PVC insulated and unsheathed FRLS cable as earth continuity conductor to common earth and connecting to earth dolly and including taking down old u/s sub main wiring complete all as specified and directed. Note: - Two runs of main cable, one run of earth continuity conductor and one run of conduit/casing-caping will be measured and paid as one length only.

S & F second class hardwood rectangular block open recessed of size 30cm x 25cm x 5 cm depth with 3 mm thick phenolic laminated sheet top cover fixed with suitable steel screws & PVC rawl plug (4 Nos) complete all as directed.

M & L for 40mm bore GI Pipe (Light Grade) for protection of LT cable fixed to walls/ poles/ road crossing including clamps complete all as specified and directed.

Supply and fixing LED type street DRACO Series , light luminaire 20 Watt 230 V, 50 Hz and including all necessary fitting accessories and LED complete all as specified and directed. Make:- Cat Part No LTESS20WLED of make C & S or equivalent model of make Crompton/ Greaves/Wipro

Supply / Lying, jointing and testing XLPE insulated armoured heavy duty LT under ground cable with aluminium stranded conductor, 1100 volts grade cross sectional area 35 Sqmm 3.5 core laid in trenches/ ducts/ through pipes, under floors or roads/along poles etc complete all as specified and directed. Note :- Sand cushioning, Cable protection, GI protection pipe, Clamps, Jointing kits and Excavation & Earth work shall be measured & paid for separately.

M&L for earthing complete with galvanized steel earth plate electrode 600x 600 x 6.3 mm thick buried directly in ground (earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 M deep below normal ground level and connected to galvanised iron earth wire 4mm dia by means of bolts, nuts, checknuts and washers of GI or steel all as shown in electrical plate No 3 of SSR Part-I 2009 and connection to main switch board / Test point /panel /equipment all as specified or indicated and testing on completion as directed by the Engineer-in-Charge including necessary excavation & earth work in any type of soil, returning, filling in and removal of surplus soil to a distance n exc 50 M, Charcoal and Salt in alternate layer 15cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20mm dia for watering and 15 mm dia 3 M long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25mm x 3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1 40mm thick precast RCC pit cover1:2:4 type B1 shall be provided on CI frame etc complete, all as specified & directed.

DEEPENDRA SINGH SHEKHAWAT

M/s S Amarjit Singh

Radha Enterprises