CONSTRUCTION OF NEW TALUKA PANCHAYAT OFFICE BUILDING AT KHERALU TA. KHERALU, DIST. MEHSANA

BILL OF QUANTITIES

Memorandum showing items of works to be carried out

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

1 Excavation for foundation upto 1.50mt.Depth including sorting out and stacking of 946.00 Cum. 157.08

useful materials and disposing of the excavated stuff as directed with in all lead & Lift

(B) Dense or Hard soil.

2 Excavation for foundation up to 1.50 M. to 3.0 mt. Depth including sorting out and 570.00 Cum 170.40

stacking of useful materials and disposing of the excavated stuff up to 50M. Lead (B)

Dense or hard Soil

3 Excavation for foundation up to 1.50 M. to 3.0 mt. Depth including sorting out and 31.00 Cum 300.80

stacking of useful materials and disposing of the excavated stuff up to 50M. Lead (D)

Soft Rock not requiring blasting

4 Filling foundation and plinth with murrum or selected soil in layers of 20 cm. thickness 102.00 Cum 399.94

includind watering, ramming and consolidating etc. comp.

5 Filling available excavated earth excluding rock in trenches plinth side of foundation 856.80 Cum 136.92

etc. in layer not exceeding 20cm. In depth consolidation each deposited layer by

ramming and watering.

6 Filling foundation and plinth with sand under floors including watering, ramming and 181.00 Cum 269.75

consolidating dressing etc, comp.

7 Applying general insecticide pest control treatment to floors, cupboards etc including 610.00 Sqm. 80.62

labour materials etc. complete. Using Imidacloprid 30.5 SCas Per IS 6313 part - II(

(0.075% concentration by mass) is recommended 10.5ml chemical diluted with 5 liters

of water application 0.5 litre chemical /Sqm of surface is recommended as per I.S

8 Providing and laying controlled cement concrete M-150 and curing complete excluding 60.00 Cum 4022.83

the cost of form work anad reinforcement concrete work in:(a) Foundation footing

base of column and mass concrete.

9 Providing and laying controlled cement concrete M-250 and curing complete including 224.00 Cum 4471.27

the cost of form work but excluding the cost of reinforcement concrete work in

Foundation footing bases of column.

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

10 Providing and laying controlled cement concrete M-250 and curing complete including 37.00 Cum 6894.26

the cost of form work but excluding the cost of reinforcement concrete work in

Column upto floor two level. Upto ground level.

11 Providing & laying cement concrete 1: 3 : 6 ( 1 Cement : 3 Coarse sand : 6 graded B.T 297.00 Cum 3194.66

stone aggregate 20mm nominal size) Curing comp. including cost of form work in

foundation and plinth.

12 Providing and laying Controlled cement concrete M200 using B.T. stone aggregate and 31.00 Cum. 7404.31

curing etc. complete including the cost of form work but excluding the cost of

reinforcement. (a) Column for Ground floor.

13 Providing and laying Controlled cement concrete M200 using B.T. stone aggregate and 31.00 Cum. 7443.60

curing etc. complete including the cost of form work but excluding the cost of

reinforcement. (a) Column for First floor.

14 Providing and laying Controlled cement concrete M200 using B.T. stone aggregate and 12.00 Cum 7482.89

curing etc. complete including the cost of form work but excluding the cost of

reinforcement. (a) Column for Second floor .

15 Providing and laying Controlled cement concrete M 250 using B.T. stone aggregate and 147.00 Cum 5835.78

curing etc. complete including the cost of form work but excluding the cost of

reinforcement for (c) PLINTH BEAM having cross sectional area more than 0.12 sqm

16 Providing and laying controlled cement concrete M-150 and curing complete including 92.00 Cum. 4284.42

the cost of form work but excluding the cost of reinforcement for reinforced concrete

work in Plinth PLINTH Slab .

17 Providing and laying controlled cement concrete M-200 and curing complete including 1.00 Cum. 6201.40

the costof form work but excluding the cost of reinforcement for reinforced concrete

workn in Wall caps / Coping / Lintel bends Ground Floor.

18 Providing and laying controlled cement concrete M-200 and curing complete including 53.00 Cum. 6447.84

the cost of form work but excluding the cost of reinforcement for reinforced concrete

work in BEAMS Ground Floor.

19 Providing and laying controlled cement concrete M-200 and curing complete including 49.00 Cum. 6487.13

the cost of form work but excluding the cost of reinforcement for reinforced concrete

work in BEAMS First Floor.

20 Providing and laying controlled cement concrete M-200 and curing complete including 5.00 Cum. 6526.42

the cost of form work but excluding the cost of reinforcement for reinforced concrete

work in BEAMS Second Floor.

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

21 Providing and laying controlled cement concrete M-200 and curing complete including 9.50 Cum. 7568.94

the cost of form work but excluding the cost of reinforcement for reinforced concrete

work in LINTELS Ground Floor.

22 Providing and laying controlled cement concrete M-200 and curing complete including 10.00 Cum. 7608.23

the cost of form work but excluding the cost of reinforcement for reinforced concrete

work in LINTELS First Floor.

23 Providing and laying controlled cement concrete M-200 and curing complete including 3.30 Cum. 6620.55

the cost of form work but excluding the cost of reinforcement for reinforced concrete

work in CHHAJJAS Ground Floor.

24 Providing and laying controlled cement concrete M-200 and curing complete including 6.00 Cum. 6659.84

the cost of form work but excluding the cost of reinforcement for reinforced concrete

work in CHHAJJAS First Floor.

25 Providing and laying controlled cement concrete M-200 and curing complete including 108.00 Cum 6398.35

the cost of form work but excluding the cost of reinforcement for reinforced concrete

work in slabs for Ground Floor.

26 Providing and laying Controlled cement concrete M200 using B.T. stone aggregate and 86.00 Cum 6437.64

curing etc. complete including the cost of form work but excluding the cost of

reinforcement. In slab for First floor.

27 Providing and laying Controlled cement concrete M200 using B.T. stone aggregate and 6.00 Cum 6476.93

curing etc. complete including the cost of form work but excluding the cost of

reinforcement. In slab for Second floor.

28 Providing and laying controlled cement concrete M-200 using B.T. stone aggregate and 7.00 Cum. 7449.76

curing complete including the cost of formwork but excluding the cost of reinforcement

for reinforced cement concrete work in staircases G.F. to F.F.

29 Providing and laying controlled cement concrete M-200 using B.T. stone aggregate and 7.00 Cum 7489.05

curing complete including the cost of formwork but excluding the cost of reinforcement

for reinforced cement concrete work in staircases F.F. to S.F.

30 Providing T.M.T. bar FE500/500D reinforcement confirmed to for R.C.C. work ####### Kg 77.63

including bending, binding, and placing. In position comp. Up to floor two level. For All

31 Brick work using common burnt clay building bricks having crushing strength not less 170.00 Cum 3424.52

than 35 Kg./Sq.m. in foundation and plinth in cement mortar 1:6 (1 cement:6 fine sand)

(b) Conventional.

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

32 Brick work using common burnt clay building bricks having crushing strength not less 107.00 Cum 3706.17

than 35 Kg./ Sqm. in cement mortar 1:6 ( 1 cement : 6 Fine sand ) in super structure

above plinth level upto floor two level ( for G.F ) Conventional

33 Brick work using common burnt clay building bricks having crushing strength not less 108.00 Cum 3740.39

than 35 Kg./ Sqm. in cement mortar 1:6 ( 1 cement : 6 Fine sand ) in super structure

above plinth level upto floor two level ( for F.F ) Conventional.

34 Brick work using common burnt clay building bricks having crushing strength not less 49.00 Cum 3774.61

than 35 Kg./ Sqm. in cement mortar 1:6 ( 1 cement : 6 Fine sand ) in super structure

above plinth level upto floor two level ( for S.F ) Conventional.

35 Half brick masonary in common burnt clay building bricks having crushing strength 188.00 Sqm. 656.74

not less than 35kg./sq.cm. in cement mortar 1:3 (1 cement : 3 coarse sand ) with 2nos.

of 6mm dia mild steel round bars every three coarse embedded in cement mortar in

superstructure for Ground floor (Conventional)

36 Half brick masonary in common burnt clay building bricks having crushing strength 185.00 Sqm. 662.21

not less than 35kg./sq.cm. in cement mortar 1:3 (1 cement : 3 coarse sand ) with 2nos.

of 6mm dia mild steel round bars every three coarse embedded in cement mortar in

superstructure First floor (Conventional)

37 Providing and fixing door Double shutter having factory fabricated std. Extruded 20.00 Sqm. 5826.69

aluminium colour anodized hollow section {Section 63.50 x 38 mm x 2.50 mm thick }

for door frame, hollow portion of door frame shall be filled with wood to be insert for

durable grip of door hinges, with factory made 38 mm.thick flush door with both side

1mm thick laminated with 6 Lever Mortice lock , SS Aldrop 30cm long, SS Handle size

15 Cm Long, Tower Bolt size 20 cm etc. as per detail colour & pattern approved by this

office including necessary anodized alluminum fixtures and fastenings.

38 Providing and fixing door Single shutter having factory fabricated std. Extruded 92.00 Sqm. 4133.93

aluminium colour anodized hollow section {Section 63.50 x 38 mm x 2.50 mm thick }

for door frame, hollow portion of door frame shall be filled with wood to be insert for

durable grip of door hinges, with factory made 38 mm.thick flush door with both side

1mm thick laminated with 6 Lever Mortice lock , SS Aldrop 30cm long, SS Handle size

15 Cm Long, Tower Bolt size 20 cm etc. as per detail colour & pattern approved by this

office including necessary anodized alluminum fixtures and fastenings.

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

39 Providing & fixing FRP Frame size100 x 50mm and 35mm think FRP depress pannel 37.00 Sqm. 2118.49

shutter having extra reinforcement on sides ad edges and in gel coat finish. The cores of

the shutter is to be filled up with intected fire extinguishing grade polyurethane

wooden pieces for stiffening and also for taking hinges and fixtures. The FRP shutter is

to be water proof, weather proof, termite proof and resistance to mild acid / Alkali

including S.S hinges with necessary screws and alluminium fixtures and fastenings &

Fastener Sleeve.

40 Providing and fixing Anodized Alluminum Section Jindal Deluxe Partly Fixed & Partly 86.00 Sqm 2081.61

Sliding Window THREE track window as shown in elevation, shutter with 5mm thick

transparent plain float glass, with transparent silicon sealant with allu. anosized coated

fittings and fixture etc complete.

41 Providing and fixing Anodized Alluminum Section Jindal Deluxe Partly Fixed & 128.00 Sqm 3086.56

Partly Sliding Window Two track window as shown in elevation, shutter with 5mm

thick transparent plain float glass, with transparent silicon sealant with allu. power

coated fittings and fixture etc complete.

42 Providing and fixing standared extruded of alluminium section of size 63.50 x 38.10 x 24.00 Sqm 1525.00

1.95 mm @ Wt 1.094Kg / Rmt with colour Powder Coated alluminium frame with

mm thick transparent bronze colour tinted float glass as details etc complete for Fix

43 Providing and fixing standared extruded of alluminium section of size 63mm x 12.00 Sqm 1175.56

38.10mm x 1.2mm @ Wt. 0.643 Kg/mt) with colour anodized alluminium frame for

ventilation with 5 mm thick frosted glass as details etc complete for Ventilation

{Colour as directed by Engineer in charge except black & Alluminum section and glass

44 Providing and fixing standard GI Chanel frame for ventilation with fixed louvers 23.00 Sqm 1596.81

114mm wide G.I.sheet with thickness of 0.55mm & wt. not less than 400gm per meter

roll formed to create 84mm wide louver snap fixed on special shaped GI channel. Fix

louvers & Channels shall finished with powder coating of 55microns etc. complete.

45 Providing and fixing Safty grills of required pattern for windows Rectangular CRC 6340.00 Kgs. 111.50

pipes of size 50 x 30 x 2mm & 16mm dia M.S. bar at 10cm spacing as per design

including fixing rat mesh and hold fasting with coach bolts including one coat of

primer and two coats of matt inished oil painting etc complete.

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

46 Providing and laying Machine cut, Free edges, Machine polished Granite stone slab 18 95.00 Sqm 3378.45

mm (Average) thick {Single piece not more than 150 cm } for stair steps and riser as

per design incl. full moulded round front edge & 1 cm nosing & necessary groobe on

trade of steps laid on 20 mm thick cement mortar 1:6 (1 -cement : 6 coarse sand )

jointed with grey cement slurry including rubbing and polishing etc. complete

47 Providing and laying 60 x 60cm Matt Finished Vitrified tiles 8 to 10 mm thick with 328.00 Sqm 1120.36

pattern colour & Shade as detailed approve by architect in flooring treads of steps and

landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand)

finishing with flush pointing in white cement.

48 Providing and laying 60 x 60cm Matt Finished Vitrified tiles 8 to 10 mm thick with 19.00 Sqm 1195.02

pattern colour & Shade as detailed approve by architect in skrting risers of steps and

dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with

white cement slurry

49 Providing and laying 60 x 60cm Soluble Salt Vitrified tiles 8 to 10 mm thick with 537.00 Sqm 1427.72

pattern colour & Shade as detailed approve by architect ( 10% Dark colour tiles

Pattern ) in flooring treads of steps and landing laid on a bed of 12mm thick cement

mortar 1:3 (1-cement : 3-coarse sand) finishing with flush pointing in white cement.

50 Providing and laying 60 x 60cm GTV Vitrified tiles 8 to 10 mm thick with pattern colour 35.00 Sqm 1502.37

& Shade as detailed approve by architect ( 10% Dark colour tiles Pattern ) in skrting

risers of steps and dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand)

and jointed with white cement slurry

51 Providing and laying 60 x 60cm Antiskid Vitrified tiles 8 to 10 mm thick in flooring 87.00 Sqm 1467.72

treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement :

3-coarse sand) finishing with flush pointing in white cement.

52 Providing and laying 30 x 30 cm size Ceramic tiles 6mm thick in flooring treads of steps 29.00 Sqm 965.65

and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand )

finishing with flush pointing in white cement.

53 Providing and laying 30 x 60Cm size Ceramic tiles 6mm thick in skrting risers of steps 324.00 Sqm 1080.96

and dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed

with white cement slurry

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

54 Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block 708.00 Sqm 699.84

60mm thick with grade of concrete M300 pnumatic compressed / vibrated

mechanically and as per approved design Confirming to IS 15658 : 2006 including

mm Sand layer for levelling and filling the joint with sand in proper line and level as

per guidlines of IRC : SP 63-2018 etc. Complete

55 Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block 139.00 Rmt. 374.92

30cm length,30cm height and 15cm thick of M250 grade concret as per approved

design and including excavation for fixing in proper line and level,filling the joint with

C:M 1:3 (1cement:3fine sand) etc complete.

56 Providing and laying water proofing tretment with chaina mosaic tiles flooring over 549.00 Sqm 1095.85

avg 40 mm C.C. 1:2:4 ( 1 Cement, 2 sand, 1 Kapchi 20mm + 3 grit 6mm to 10mm )

bedding for maintaining slope for plain and curve surface & 12 mm to 20 mm of

broken piece of ceramic / glazed tiles ( one or more color as directed ) to be laid over

cement mortar bedding of C M 1:3 (1 cement : 3 sand ) containg one Kg. of water

profing materials per bag of O P C at plain or / and slops and to be tempered to bring

mortar ceramic up to surface with using white cement and colour pigment including

rounding of junctions and extending them up to 15 cm along the wall and curing with

bends any pattens or design as per drawing and cleaning by using oxalic acid etc

57 Providing and laying Mirror polished Machine polished Green Marble stone slab 18mm 253.00 Sqm 2530.05

(Average ) thick for doors & windows sill & Jams clading as per design including full

moulded round front steps & 1cm nosing & necessary groove on trads of steps ;laid on

20mm thick cement mortar 1:6 ( 1 cement : 6 coarse sand ) jointed with gray cement

sluury including rubbing and polsihing etc. complete.for Doors / windows sill & jams

58 Providing 20 mm thick double coat mala cement plaster on interior brick / concrete 1159.00 Sqm 284.33

work for plastering comprising of base coat of 12 mm thick cement plaster in cement

mortar (1 Cement : 4 coarse sand) in rough finishing and 8 mm thick top coat of cement

mortar 1:2 (1 Cement : 2 Coarse sand) finished with trovel including scaffolding curing

etc. complete. For Ground Floor

59 Providing 20 mm thick double coat mala cement plaster on interior brick / concrete 1325.00 Sqm 311.60

work for plastering comprising of base coat of 12 mm thick cement plaster in cement

mortar (1 Cement : 4 coarse sand) in rough finishing and 8 mm thick top coat of cement

mortar 1:2 (1 Cement : 2 Coarse sand) finished with trovel including scaffolding curing

etc. complete. for First Floor

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

60 Providing 20 mm thick double coat mala cement plaster on interior brick / concrete 219.00 Sqm 338.87

work for plastering comprising of base coat of 12 mm thick cement plaster in cement

mortar (1 Cement : 4 coarse sand) in rough finishing and 8 mm thick top coat of cement

mortar 1:2 (1 Cement : 2 Coarse sand) finished with trovel including scaffolding curing

etc. complete. for Second Floor

61 Providing 10mm thick cement plaster in single coat on brick/concrete walls for interior 536.00 Sqm 216.14

plastering upto floor two level and finished even and smooth in (i) Cement mortar 1:3

(1-cement:3-sand) including finishing with a flating coat of neat cement slurry etc.

complete. for Ground Floor

62 Providing 10mm thick cement plaster in single coat on brick / concrete walls for 493.00 Sqm 237.10

interior plastering upto floor two level and finished even and smooth in (i) Cement

mortar 1:3 (1-cement:3-sand) including finishing with a flating coat of neat cement

slurry etc. complete. for First Floor

63 Providing 10mm thick cement plaster in single coat on brick/concrete walls for interior 24.00 Sqm 258.89

plastering upto floor two level and finished even and smooth in (i) Cement mortar 1:3

(1-cement:3-sand) including finishing with a flating coat of neat cement slurry etc.

complete. for Second Floor

64 Providing 20 mm thick Water proof cement plaster for sunk in single coat on bricks/ 102.00 Sqm 203.01

concrete wall for interior plastering upto floor two level finished even and smooth (ii)

Cement mortar 1:3 (1- cement : 3-sand) and mixing waterproofing materials of

approved brand and manufacture in cement mortar in proportion recommended by

the manufacturer for All Floors.

65 Providing and fixing chiken mesh jali with square of 12.50 x 12.50 mm of 25 gauge at 431.00 Sqm 92.92

junction the Brick.masonary and reinforcement cement concrete member including

fixing materials scaffolding labour etc. complete

66 Applying two coats of putty & two coats of primer of approved brand and manufacture 3707.00 Sqm 40.59

on new wall surface to give an even shade including thoroughly brushing the surface

free from mortar dropping and other foreign matter and sand papered smooth. For all

67 Wall painting (three coats) with plastic emulsion paint of approved brand and 2715.00 Sqm 125.50

manufacture on undecorated wall surface to give an even shade including throughly

brushing the surface free from mortar droppings and other foreign matter and sand

papered smooth including

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

68 Wall painting (three coats) with plastic emulsion paint of approved brand and 1024.00 Sqm 131.02

manufacture on undecorated ceiling surface to give an even shade including throughly

brushing the surface free from mortar droppings and other foreign matter and sand

papered smooth.

69 20mm thick sand faced cement Gutka finished plaster on walls upto height 10 metres 1524.00 Sqm 321.10

above ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-

sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. complete.

70 Providing and fixing 90 cm high Stainless steel railing made from anticorrocive S S 35.86 Rmt. 3144.13

pipe of 50 mm dia (16Gauge) as hand rail with S S 38 mm dia (16Gauge) as a vertical

support fixed in RCC slab at 1.2m c/c including three horizontal S S pipes of 25 mm

dia (16Gauge) at eqal distance fixed by 18.75 mm dia (16Gauge) S S pipe including

accessories as per detailed drawing as directed etc. complete.

71 Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH- 40) 96.00 Rmt. 72.65

for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed

on the wall with the help of clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of all materials.

72 Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40) 90.00 Rmt. 91.84

for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed

on the wall with the help of clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of all materials. [B] 25mm dia.

73 Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH- 40) 80.00 Rmt. 148.12

for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed

on the wall with the help of clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of all materials.[D] 40 mm.

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

74 Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH- 40) 150.00 Rmt. 195.67

for cold water including fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of all materials.[E] 50 mm.

75 Providing and fixing Handle valve of aprroved brand (B) 25mm dia., 6.00 Nos. 383.80

76 Providing and fixing Handle valve of aprroved brand (C) 40mm dia., 6.00 Nos. 566.61

77 Providing and fixing Butterfly valve of IS aprroved brand (C) 50mm dia., 4.00 Nos. 813.56

78 Providing and fixing to wall, ceiling and floor galvanised Mild steel tubes (Medium 100.00 Rmt. 608.35

grade) of the following nominal bore, tube fitting and clamps including making good

the wall ceiling and floor.(E) 40mm

79 Providing, laying and jointing in true line and level 75 diametre U.P.V.C (Type B) 80.00 Rmt. 797.98

conforming to IS 13592-1992 with one end plain and other end socketed with rubber

ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system

pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be

fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x

mm heigh at every 2000 mm center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement including cost of all materials.

80 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure 225.00 Rmt. 339.05

poluthene pipes of the following outside Dia. Low densidy, complete with special flange

compression type fittings, wall clipsetc. including making good the wall ceiling and

floor.(A) 110mm dia.

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

81 Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) 110.00 Rmt. 876.11

conforming to IS 13592-1992 with one end plain and other end socketed with rubber

ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system

pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be

fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x

mm heigh at every 2000 mm center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement including cost of all materials.

82 Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) 140.00 Rmt. 834.38

conforming to IS 13592-1992 with one end plain and other end socketed with rubber

ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system

pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be

fixed on wall using of PVC clamp of the size 160 mm diametre x 210 mm length x

mm heigh at every 2000 mm center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement including cost of all materials.

83 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with 24.00 Nos. 586.60

jali of the following nominal diameter of self cleansing design with C.I scread down or

hinged grating including the cost of cutting and making good the walls.

84 Providing and fixing screw down quarter turn bib taps of following size (A) Brass 38.00 Nos. 186.83

chromium plated screw down bib tap (i) 15mm dia.

85 Providing and fixing CP brass Quarter turn pillar tap, capstan head screw down high 14.00 Nos. 308.73

pressure with screw, shanks and back ndts (A) 15 mm dia Long pipe}

86 Providing and fixing wash basin with pedestal of std. Height with single hole for pillar 14.00 Nos. 1883.65

tap with C.I or M.S brackets painted white including cutting cutting holes and making

good the same including C.P. brass waste and waste pipes and bottal trap (A) Vitreous

China: (ii) Flat Back washbasin 550 mm x 400mm size.In colour.

87 Provision and fixing water closet squatting orissa type W.C. pan size 580mm integral 4.00 Nos. 1340.27

footrest and 100mm p or s trap and including 25mm dia. C.P. brass flush valve and G.I.

inlet connection etc. complet (A) Viterous china long pattern white or colour

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

88 Pro. & Fix.wash down water closet (European w. c .pan) with integral" p " or " s " trap 14.00 Nos. 2333.10

and PVC flushing cistern with a pair of C.L.I. Or Mild steel Brackets, complete with

fittings such as lead value siphon, 15 mm. Nominal size brass ball valve with polythene

float, C.P. Brass handle unions and couplings for connections with inlet, outlet and over

flow pipes, 40 mm. dia. flush bend including cutting holes in walls and making good the

same connecting the flush bend with cistern and closet etc comp incl plastic sheet cover

including jointing trap with pipe in cm 1:1 (a) Viterous china in white or colour

89 Providing and fixing Special Needs Range CRUSE SET, EWC, 710 x 370 x 810 mm, New 1.00 Nos. 58378.00

Cat No: S1021113 S Trap, S1021114 P Trap, S1060106 Cistern, B1520118 Soft Close

Seat Cover, B1810112 Twin Flush Fittings, S2040101 Wash Basin 510 x 400 mm,

F9030451 Spatula Lever basin mixer, B2210106 Wall mounted Grab bar 600 mm long,

B2210106 Wall mounted Grab bar 600mm long, B2210108 Wall mounted Hinged

rail 750 x 750 {Cera or equivalent} as directed by Architect Office {SUGAMYA

BHARAT Instruction}

90 Providing and fixing urinal of approved quality connecting the urinal with waste pipe, 8.00 Nos. 1074.86

trap etc. complete. (A) White earthenware flat back or corner type size 430mm x

91 Providing and laying Both side mirror polished Granite marble stone slab 18 mm 5.40 sqm 1674.58

(Average) thick of approved quality moulded round front edge fixed in wall for

partition and jointed with grey cement slurry including rubbing and polishing complete

92 Providing erecting and fixing double coated PVC. (ISI) water tank of required capacity 21000.00 Litre 3.95

each with all necessary fittings and connection etc. complete on terrace.

93 Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass 14.00 No. 859.41

mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with

C.P. brass screws and washers.

94 Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to 14.00 No. 616.42

wooden plugs with C.P. brass scews.(B) 600mm x 20mm size.

95 Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water 10.00 No. 1246.92

tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i)

Square mouth traps.(B) 150mm x 100mm size P of R type

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

96 Providing and fixing CP brass screw down stop cock of approved quality 15mm size 36.00 No. 205.83

with adjustable wall flange..

97 Constructing brick masonry chamber for underground C.I. Inspection chamber and 10.00 No. 2932.93

bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I.

cover with frame (Light duty) 455mm x 610mm intenal dimensions, total weight of

cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg.

) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate

20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar

1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc.

complete.(i) Inside dimensions 455mmx 610mm and 450mm deep for single pipe

98 Constructing brick masonry chamber for underground C.I. Inspection chamber and 15.00 No. 3660.76

bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I.

cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of

cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg.

) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate

20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar

1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc.

complete.(ii) Inside dimensions 500mm x 700 mm and 450mm deep for pipe line

with one or two inlets.

99 Constructing brick masonry chamber for underground C.I. Inspection chamber and 5.00 No. 7180.44

bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I.

cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of

cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg.

) (R.C.C. top slab with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate

20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar

1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc.

complete.(iii) Inside dimensions 600mm x 850mm and 450mm deep for pipe lines

with three or more inlets

100 Providing and filling screened of burnt coal cinder including and consoliation etc. 11.00 Cum. 621.46

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

101 Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) 1567.00 Sqm 76.75

to give an required shape even shade after thoroughly brushing the surface to remove

all dirt, and remains of loose powdered materials.etc complete

102 Providing thoruting or plaster drip and moulding to R.C.C. chhajja. 54.00 Rmt. 43.05

103 Providing 12mm wide groove throating / notch in plaster including finishing the same 572.00 Rmt. 15.15

etc. complete for all height.

104 Constructing Sandwitch Platform of 18 mm thick Polished Black Granite at top and 25 6.00 Sqm 3112.82

mm thick Kota stone slab using cement mortar 1:3 for sandwich and fitting at bottom &

edges with waterproof rigid adhesives including macking necessary grooves in walls

with Vertical Kotastone 30 mm x 2 No sandwitch thick every 60 cm centre to cenre

including all labour material of approved quality incl. full moulded round front edge

fixed in wall for partition and jointed with grey cement slurry including rubbing and

polishing etc. complete

105 Providing and fixing in position 300mm high , 150mm wide englsih letter made from 30.00 No. 707.00

1.0mm thick stainless steel sheet as directed by enginer in charge with all necessary

tolls & plants etc. complete.

106 Providing and fixing in position 150mm high , Englsih letter made from 1.0mm thick 100.00 No. 404.00

stainless steel sheet as directed by enginer in charge with all necessary tolls & plants

107 Providing water proofing agent for RCC ( Perma - plast SL for M-25 Concrete) as per 291.00 Kgs. 101.00

Aapproved quality of ASTMC494 conforming IS9103-2007 &2645-2003.

108 Providing water proofing agent for Plastering ( Perma Grout - 500) ( Only Wall Qty. 48.00 Kgs. 110.09

109 Providing perma bitu coat for foundation ( Water proofing agenct as well as antitermite 250.00 Kgs. 244.42

treatment for footing and comoumns,

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

110 Providing and fixing acrylic multilingual Braille (raised dots) DIRECTIONAL 36.00 No. 1708.92

SIGNBOARDS of size 225 x 150mm designed as per accessibility standards and having

3.5mm thick acrylic base plate with Upper Case San Serif words made of white acrylic

non glare cut out letters of height 15mm raised not less than 0.8mm above base plate

and the equivalent word written in Hindi with Devanagari non glare acrylic letters of

height 15mm raised not less than 0.8mm above base plate and having a non-glare

acrylic cut arrow pointing in the required direction. Each signboard to be fixed as per

manufacturers specifications on the wall at the approved location and at a height of

1200mm from FFL complete as per design / specifications and guidelines as per the

entire satisfaction of the Engineer

111 PROVIDING & FIXING BRAILE INDICATOR OF SIZE 170 MM X 35MM FOR HANDRAILS 57.00 Rmt. 832.24

OF THE APPROVED DESIGN AND MAKE H BRAILE DOTS RAISED 0.5 MM ABOVE BASE

PLATE TO BE INSTALLED AT SPECIFIC LOCATIONS AS PER DIRECTION ENGINEER IN

112 Providing and fixing of conspectus tape 50mm width on of treads in staircase including 32.00 Sqm. 1355.42

cutting pasting etc. As per harmonised guidelines complete in all respect to the entire

satisfaction of engineer in charge.

113 Providing & laying cement concrete 1:4:8 (1 Cement : 4 Coarse sand : graded B.T. stone 16.00 Cum. 2643.35

aggregate 40mm nominal size) Curing comp. including cost of form work in foundation

114 Providing and laying controlled cement concrete M-250 and curing complete including 7.00 Cum. 4471.27

the cost of form work but excluding the cost of reinforcement concrete work in

Foundation footing bases of column.

115 Providing and laying controlled cement concrete M-200 and curing complete including 6.00 Cum. 6201.40

the cost of form work but excluding the cost of reinforcement for reinforced concrete

work in Wall caps/Copping Ground Floor

116 Providing 15mm thick cement plaster in single coat on fair side of bricks/ concrete wall 487.00 Sqm. 209.21

for interior plastering upto floor two level finished even and smooth in cement mortar

1:4 ( 1 cement :4 sand ) etc. complete.

117 Providing and fixing mild steel door with 40 x 40 x 6 mm angle for frame and for 200.00 Kgs. 111.50

shutter frame 30 x 30 x 3 angle. For windows frame of angle 35 x 35 x 5 & for shutter

windows 25 x25 x 3 mm size angle and 18 gauge sheet for panels & 10 mm dia bars at

10 cm c/c for grill and 40 x 6 mm flats on edge of shutter, & 20 x 6 mm binding patti,

including one coat of primer and two coats of oil painting etc. comp. as per detail / as

directed by Engineer in charge.

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

118 Providing and laying hand dressed polished blue Kota stone slab flooring over 20mm 11.00 Sqm. 1019.00

(Average) thick base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 laid

over and jointed with grey cement slurry including rubbing and semi miror polishing

with emery No. 600 etc. complete. (A) 25mm thick

119 Distempeing (Three coats) with oil bound washable distemper of approved brand and 61.00 Sqm. 110.62

manufacture and of required shade on wall surfaces to give an even shade, over and

including a priming coat with alkali resistance primer of approved brand after

thoroughly brushing the surface and other foreign matter and also including preparing

the surface even and sand parpered smooth.

120 Providing cement vata (10cm. x 10 cm. size) quarter round in cement mortar 1:1 19.00 Rmt. 24.28

including neat cement finishing, watering etc. complete.

121 Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size having weight not less 5.00 No. 958.17

122 Box cutting the road surface to proper slope and chamber for making a base for road 467.00 Cum. 109.05

work including removing the excavated stuff and depositing on the road side slope as

directed up to 50 mts. Lead.

123 Supplying and laying, spreading and compacting coarse clean sharp specified sand 134.00 Cum. 537.32

(C.B.R. not less than 10%) below sub base course including carraige of material

spreading in uniform layers manually on prepared base and compacted with power

roller to achieve desired density including all materials, labours etc. complete. and

spreading coarse clean sand as directed.

124 Provdining and laying W.B.M of B.T.M.C metal of size 45 mm to 63 mm size including 200.00 Cum. 1611.96

0.12 Cu.M. Stone Screeing & 0.08 Cu.M. stone dust as filler including spreading,

watering & consolidation by vibratory roller 80KN to 100KN static weight. 75 mm thick

compected each of two layer.

125 Providing and laying controlled cement concrete M.250 and curing complete including 200.00 Cum. 4298.56

the cost of formwork and reinforcement for reinforced concrete work in(A)

Foundations, footings, Base of columns and Mass concrete

126 Compaction and finishing of cement concrete road by tremix process, providing extra 1334.00 Sqm. 85.85

labour charge for tremix ( Vaccum dewatering service ) process on cement concrete

road surface by using vaccum dewatering pump floater surface vibrator including

making groove 5mm width and filling with polyvynile polymer and rough finish to

surface as per instruction including leveling etc. complete.

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

127 Providing and fixing junction board of M.S.plates and angles as per standered IRC 2.00 No. 5236.70

design including fixing in C.C. 1:4:8 with necessary excavation , painting, figuring and

lettering on board etc. comp.

128 Providing and laying cememt concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone 9.20 Cum, 3587.13

aggregate 20mm nominal size ) and curing complete excluding cost of form work in (a)

foundation and plinth.

129 Providing and fixing 72 x 72 x 3.2mm thick M.S. pipe parking shed post & Rafter , MS 48.25 Qtls. 9108.48

50 x 50 x2mm pipe purlines with necessary M.S. plate 8mm hick including cutting

bending , grinding , welding , drilling for nut bolts including painting two coats of oil

painting over primer coat etc. complete.

130 Providing and fixing 6mm thick polycarbonate multi wall roofing sheet fixed with hilti 425.00 Sqm. 1441.90

screw and rubber silicon sealer and alluminium strip of size 50x 3 mm etc complete as

directed by engineer in charge

131 Providing water harvesting pit 2.40 mt dia x 2.40 mt depth with excavation in any 2.00 No. 61649.39

strata filling the pit with brick bats in 0.60 mt depth, 0.30 mt with 25mm to 40mm

kapchi 0.30 mt with 10mm to 20mm kapchi & 2.00 mm depth with coarse sand in layer

including maing the lines (PVC) for water inlet etc. as directed including 250mm dia

bore work with 6" PVC" pipe upto 35mt etc, comp.

132 Plantation of trees in soil including digging 45 x 45 x 45cm size pits, preparing soil 50.00 No. 40.40

providing and mixing fertilizer, watering, planting and filling the pits as per direction

including etc. complete

133 Providing Tree Plants having minimum 1.00mt. Height and healthy grouwth of various 50.00 No. 25.25

kinds as like Peltoform, Palm,Gulmahore, Karanj, Amla, Rain tree, Saptparni, Cherry,

Cryjeliya, Spethodiya, Paras Pipala, Garmalo, Neem, Borsalli, Kadam, Buch, Chanpo,

Asopalav etc. as per instruction by engineer in charge.

134 Providing and errecting open well type horizontal monoblock pumpset with C.I. body 1.00 No. 11342.30

having following specification. (i) 1H.P. Single phase open well motor pumpset suitable

for 145lpm ( ii) Suitable for 32 dia delivery pipe with control panel & 10mtr. Long

135 Screen Filter 7000 ltr capacity per hr 1.00 No. 1464.50

136 Pressure Gauge 1.00 No. 313.10

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

137 Bypass Assembaly 1.00 No. 1818.00

138 32 dia Control Valve 1.00 No. 323.20

139 16mm internal HDPE pipe 2.5Kg. Including fitting 260.00 Rmt. 8.89

140 Providing and fixing gun metal check or non return fullway controll wheel valve 50mm 3.00 No. 1111.00

141 Providing and laying in trenches 10.0kg.f/ Sqcm working pressure PVC pipes for water 200.00 Rmt. 173.98

sully line of the follwing outside dia having white colour complete with necessary

fittings clamps etc. (B) 50mm

142 Providing and laying in trenches 10.0kg.f/ Sqcm working pressure PVC pipes for water 100.00 Rmt. 123.47

sully line of the follwing outside dia having white colour complete with necessary

fittings clamps etc. (A) 32mm

143 Painting two coats (including priming coat) on new steel and other metal surface with 286.00 Sqm. 129.04

enamel paint, brushing interior to give an even shade including cleaning surface of all

dirt, dust and other foreing matter.

144 Filling in Garden with selected soil in layers of 20 cm. thickness includind watering, 298.00 Cum. 269.75

ramming and consolidating etc. comp.

145 Planting of lawn of approved quality at 15 cms diagonally, maintenance of the lown till 994.25 Sqm. 50.50

virtual completion of soft landscape work : removal of all thatching through out the

area: along with appropriate use of termite and of weedixite as red when required and

146 Earth work for embankmen tincluding breaking clods, dressing with all lead and lift 4986.00 Cum. 186.57

(including watering and consolidation) including rolling of earth work in layers with

power roller including filling indepressions which occur during the process. (D) From

Borrow area within 2.0 Km. lead

147 Drilling of 215mm dia. Bore in over burden strata (0-30) including lowering and fixing 150.00 Rmt. 428.24

of 175 mm nominal dia UPVC pipe/175 mm dia ERW pipe upto required depth and

further drilling of 165mm dia bore hole in rocky strata by DTH rig..

148 Providing and lovering 175 mm dia PVC 6 kg / sqcm. Casing pipe in bore hole with 18.00 Rmt. 915.06

necessary fitting etc. complete.

149 Providing and fixing M.S. Cap plug hinge type with frame of required design for 175 1.00 No. 782.57

mm dia bore casing pipe

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

150 Supplying of submersible pump set Three phase for 100 mm or more dia bore having 2.00 Set 26894.28

motor capacity and discharge as under with necessary panel box motor ratting 5 H.P.

pump having capacity of 30 LPM at 90 mt. Head suitable for 32 mm dia delivery pipe

151 Supplying and erecting submersible horizontal & vertical pump set following 2.00 Set 18746.61

discharge& head 5 H.P. 3 Phase 400/ 440 VA.C. motor with following Cat. III section

and discharge flange size (C) 405 LPM at 30 mtr. head with size 50 mm cat. II.

152 Supplying & erecting approved make motor control cubical panel ( Direct -on - line ) 1.00 No 7722.46

made from 16 G. CRCA sheet duly epoxy powder coated in side and out side with

hinged doors and locking arrangement consisting of suitable size of on-off isolator (

A.C. 3123 duty) main fuses single phasing prevented in dictating lamps for R-Y-B

phases over load relay ammeter voltmeter each with two way selector switch incoming

wires duly socket crimped main connector & over load, relay start stop push button

the isolator over load relay and contactor will be of L & T , siemens cutler hammer

make only (A) D.O.L. 5.0 H.P.

153 Supplying & erecting approved make motor control cubical panel ( Direct -on - line ) 1.00 No 8710.24

made from 16 G. CRCA sheet duly epoxy powder coated in side and out side with

hinged doors and locking arrangement consisting of suitable size of on-off isolator (

A.C. 3123 duty) main fuses single phasing prevented in dictating lamps for R-Y-B

phases over load relay ammeter voltmeter each with two way selector switch incoming

wires duly socket crimped main connector & over load, relay start stop push button

the isolator over load relay and contactor will be of L & T , siemens cutler hammer

make only D.O.L. for 7.50 H.P.

154 Lowering of submersible motor pump set comlete with required nos. and size of casing 1.00 Job 2996.67

pipes erected by means of proper chian pully block & pipe wrenches after checking of

threades of each pipe with coupline take the load of the pump set and pipe assembly

fitted up with water (1) above 90 mt. and 120 mt.

155 Providing and erecting PVC insulated flat flexible cable ISI. Marked approved make of 200.00 Rmt. 104.03

(B) 3 core X 2.50 sqmm.

156 Providing and fixing H.D.P.E. PVC Column pipe heavy duty length and thread on both 120.00 Rmt. 151.50

the ends with 8TPI or 11TPI as required as directed ( a) 40 mm dia

157 Heavy duty clamp made from 4" x 1.5 " iron strips suitable for column pipe 1.5 to 2" 1.00 No. 179.78

length (A) 50 mm (1.5") dia pipe.

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

158 Providing and fixing window having extruded aluminum Colour anodized section 3.00 Sqm. 1713.70

frame main outer size 63.50 x 38.10 x 1.95 mm(of Jindal Section no:4605,@ Wt

Kg / Rmt), horizontal two track member size 61.85 mm x 31.75 mm x 1.20mm (of

Jindal Section no: 8687 @ wt.of 0.695 Kg/mt), vertical member of size 61.85 mm x

31.75mm x 1.30 mm (of Jindal Section no:8758 @ wt.of 0.0.659 Kg/mt) with sliding

shutters of horizontal member size 40mm x 18mm x 1.29mm (of Jindal Section

no:8949 @ wt.of 0.456Kg/mt), vertical member of size 40mm x 18mm x 1.29mm (of

Jindal Section no:8947 @ wt.of 0.456Kg/mt/ Section 8948, @ Wt. 0.457 Kg/mt) with

mm thick transparent bronze colour tinted float glass with powder coated aluminum

fittings and fixtures and transparent silicon sealant glass fixing to frame as per details

etc complete for window.

159 Providing and fixing M.S.Pipe Flage post of required pattern & Drawing required 110.00 Kgs. 151.50

diferance dia M.S. pipe and pulley with two coats of Oil paints with primer coats etc.

160 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both 184.00 Pts. 582.77

are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to

mtr length , in below type of pipe erected with 6A Modular type switch / bell push &

accessories and earth continuity of following type, erected on PVC / Metallic/Wooden

box, single mounting base frame covered with textured/metallic/white front plate

modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete Cat.III

161 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of 77.00 Pts. 809.01

.ISI marked 1.1 KV Grade FRLS PVC insulated multi strand copper wires up to 10 mtr

length, in below type of pipe erected with 6A Modular type switch and hum free EME

step type electronic fan regulator mounted and accessories with earth continuity of

following type erected on PVC / Metallic/Wooden box, single mounting base frame

covered with textured/metallic/white front plate modules erected on / in wall /

ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete Cat. III

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

162 Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket 61.00 Pts. 309.06

erected on PVC / Metallic/Wooden box, single mounting base frame covered with

textured / metallic/white front plate modules erected on / in wall / ceiling with

following type accessories Cat. III

163 Providing following type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate , modules erected with necessary connections as per site

situation directed by Engineer In charge.

(1)One No. SP 6 Amp. Cat.III 24.00 Nos. 151.50

(2) One No 5 pin plug Cat.III 24.00 Nos. 151.50

(3) Two Pin/RJ-11 Telephone Socket 19.00 Nos. 160.59

[A] For One Gang Cat.III

(7) Blank Plate Single Cat.III 50.00 Nos. 25.25

(8) Computer RJ-45 socket Cat.III 56.00 Nos. 160.59

(9) 16 Amp. SP one way switch Cat.III 34.00 Nos. 180.79

(10) 6/16Amp. Universal socket Cat.III 28.00 Nos. 199.98

164 Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size

complete to be erected on/in wall or ceiling erected with necessary PVC fittings &

Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in

approved manner as directed

165 Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, 15.00 Mtr. 21.21

PVC bushes, Check-nuts etc. complete of following sizes.(2) 25 mm

166 Supplying and laying UPVC cable trunking system comprising unplasticised polyvinyl, 20.00 Mtr. 428.24

chloride rigid material with ignition free and flame proof confirming BS with necessary

end caps Internal and external bend, flat bends, coupler, tee etc..All necessary

accessories and measuring of following sizes(2) 100 mm x 50 mm trunking

167 Supplying under floor pregalvanised corrosion proof rectangular sheet steel cable 70.00 Mtr. 458.54

trunking of 1.6 mm thick having with stand point load up to 1.33 Ton & free from

seepage of concrete of screed water with all accessories,Junction Box,Joints as required

and demanded by engineer-incharge and laying/erecting as per OEM guidelines and

as per instruction of engineer incharge having following size of dimensions and No of

compartments (W x D x T) Cat-III [3] 100mm x 25mm x 1.6 mm with one compartment

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

168 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked 2110.00 Mtr. 104.03

stranded Copper conductor wire in following type of pipe to be erected concealed in

/flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of following size(A) With medium

class Rigid PVC pipe and accessories (b) 2 wire 2.5 sq. mm

169 providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be erected in / on wall /

ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size (A) with medium class Rigid PVC pipe and

(a) 2 wire 4 sq. mm 510.00 Mtr. 140.39

(b) 2 wire 6 sq. mm 825.00 Mtr. 184.83

(i) 4 wire 10 sq. mm (use earth wire of 4 sq.mm ) 30.00 Mtr. 532.27

170 providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded,

annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC -

227 erected in existing pipe of following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring) with required size of copper lugs,

nuts and bolts if required.

(f) One wire 10.00 sq. mm 12.00 Mtr. 115.14

(g) One wire 16.00 sq. mm 20.00 Mtr. 177.76

(k) One wire 70.00 sq. mm 20.00 Mtr. 837.29

171 Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv grade ISI 92.00 Mtr. 58.58

marked copper wires of following size to be erected as directed.

(e) 1.50 Sq.mm 3 core round PVC sheathed

172 Supplying & erecting approved make LAN cable of following size in existing pipe as per 1960.00 Mtr. 47.47

173 Supplying & erecting approved make Telephone Cable electrolytic copper conductor PE

insulation twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS

PVC or HFFR outer Jacket suitable for telephone wiring & confirming to C-DOT erected

in existing pipe. of following size of conductors & nos.of pairs. With necessary

[A] Conductor Size 0.5 mm (a) Unarmoured (2) Two Pairs 570.00 Mtr. 20.20

5) Ten Pairs 50.00 Mtr. 65.65

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

174 Providing & erecting main Distribution (MDF) indoor type, back mounted frame as per

DoT standard approved with krone strips

(a) Suitable for 10 pair 2.00 Nos. 994.85

(b) Suitable for 20 pair 1.00 Nos. 1368.55

175 Providing & erecting Switch board for Computer or electric apparatus consisting of 56.00 Nos. 1133.22

following modular type accessories mounted with PVC / Metallic concealed/open box

with single mounting base frame covered with textured/metallic /white front

plate,modules erected with necessary connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type AccessoriesCat. III

176 Decorative call bell Ting-tong box type 250 volts complete erected 8.00 Nos. 71.71

177 Supplying and erecting led lamps with following wattage capacity of 220 to 240 17.00 Nos. 112.11

voltage, minimum 15000 burning hours life, 500 V in built-surge

protection,Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 lamp holders,

pf >= 0.5(A) LED Lamps integral type, with PC diffuser suitable LAMP holder

(ii) 5 to 8 watts Cat-III

178 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt 138.00 Nos. 373.70

assembled on single MCPCB, with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/ aluminium die cast powder coated and high

U.V. & corrosion resistance with diffuser with company mark/name 160V to 270V,

Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.)

(A) Tube Light with integral driver (iv) 22-24 Watts, Surge - 2KV,IP-20, conventional

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

179 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt

assembled on single MCPCB, with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/aluminium pressure die cast powder coated

and high U.V. & corrosion resistance with diffuser housed in aluminium casted body

with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for

spring loaded mounting clips complete.IP20

(iv) 22-24 watts, Surge-2 kV Cat-lll 6.00 Nos. 758.51

180 Supplying and erecting LED street light / Flood light fittings with High power White 22.00 Nos. 5080.30

LEDs wattage of 3 Watt and above assembled on single MCPCB, efficiency more than

130 lm/w and corrosion free High pressure die cast aluminum housing with smooth

finish powder coated and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with company mark/name

engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT

3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC

line supply with over-voltage protection.

(iii) 60 - 89 watts

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC 8.00 Nos. 6177.16

line supply with over-voltage protection.

(iv) 90 - 119 watts

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

(C) Post Top Lantern LED fitting comprises of finish cast aluminum spigot and spun 2.00 Nos. 4096.56

aluminum canopy fixed with opal polycarbonate, pipe arrangement for vertical

mounting driver and accessories wired up to terminal block.IP

181 Approved make Four Pole LT Heavy Duty Switch Disconnector Fuse Unit Cubical type

for panel mounting complete with operating mechanism suitable to operate on 415V

A.C. With HRC fuses of suitable load confirming to IS. 13947 (Part I & III). of following

(c) 125 Amp Cat.III 1.00 Nos. 6120.60

(d) 200 Amp Cat.III 1.00 Nos. 8072.93

(e) 250 Amp Cat.III 1.00 Nos. 9348.56

182 Supplying & erecting approved make Four Pole 415V change over switch interior for 1.00 Nos. 13353.21

panel mounting with operating mechanism A.C.23 duty confirming to IS for(E)250A /

(A)32-40A Cat.III For Motor Pump Panel 1.00 Nos. 2611.86

183 Providing and erecting Approved make Four pole moulded case circuit breaker having 6.00 Nos. 6790.23

breaking capacity ICU of 25 KA. at 415 V,having normal current rating up to 25 A to

100A. with Fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s.

with all internal connections, spreader tinned copper & complete erected in existing

G.M.S. housing. ICS=100% of ICU only Cat III

184 Providing and erecting Approved make Four pole moulded case circuit breaker having 2.00 Nos. 8861.74

breaking capacity ICU of 35 KA. at 415 V. having normal current rating 125A. with

Fixed thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all

internal connections, spreader tinned copper & complete erected in existing 16 G.M.S.

housing. ICS=100% of ICU only Cat III

185 Providing and erecting Approved make Four pole moulded case circuit breaker having 1.00 Nos. 17843.67

breaking capacity ICU of 35 KA. at 415 V. having Normal current rating 200A.with

variable Thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all

internal connections, spreader tinned copper & complete erected in existing

G.M.S.housing ICS=100% of ICU only Cat III

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

186 Providing and erecting Approved make Four pole moulded case circuit breaker having 1.00 Nos. 23041.13

breaking capacity ICU of 35 KA. and above at 415 V . having normal current rating

250A. with variable thermal & magnetic release suitable to work on A.C.supply 50 c/s.

with all internal connections, spreader tinned copper & complete erected in existing

G.M.S. housing. . ICS=100% of ICU only Cat III

187 Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper

Busbars with four equal Nos. of electrolyte bus having current density not more than

1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour

insulating tape for phase sequence of following current carrying capacity, erected with

necessary bus bar supports /insulators, main cable socket to each bar, erected in

existing cubical panel with necessary connections.

(A) Suitable for 100 Amp. Capacity 0.60 Rn.M 1961.42

(B) Suitable for 200 Amp. capacity 0.60 Rn.M 3202.72

(C) Suitable for 300 Amp. capacity 1.00 Rn.M 4909.61

188 providing and erecting Miniature circuit breaker single pole 0.5A to 2A system and 24.00 Nos. 297.95

having breaking capacity 10 KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark

189 providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to 130.00 Nos. 123.22

operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in

existing box. confirming to IS 8828/1996 with ISI Mark Cat.III

190 Providing & erecting 240 V MCB double pole switch for motor & inductive load (C 13.00 Nos. 362.59

Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having

following capacity

191 Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve) having 18.00 Nos. 325.22

10 KA breaking capacity & confirms to IS : 8828 in existing box having following

(B) 40 Amp. Cat.III

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

192 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) 11.00 Nos. 736.29

having 10KA breaking capacity & confirms to IS :8828 in existing box having following

capacity (b)40 Amp.

(c)63 Amp. Cat.III 2.00 Nos. 811.03

193 Plastic enclosure fitted with DIN rail suitable for incorporating One / Two nos. MCB 22.00 Nos. 52.52

194 Supplying KITKAT pattern porcelain cut-out fuse with base of following current 3.00 Nos. 420.16

capacity erected on existing block board.(vi) 200 A. 500 V.

195 Providing and erecting Sheet Steel powder coated MCB distribution board - flush /

surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be used) suitable for(A) single phase

incoming and horizontal single phase outgoing

(b) sheet steel double door (IP-43)

(iii)8 way 10.00 Nos. 1152.41

(B) three phase incoming and single phase horizontal type outgoing Per phase 1.00 Nos. 2913.85

isolation type (PPI)(b) sheet steel double door

196 providing and erecting Approved make RCCBs conforming to IS: 12640 and having 17.00 Nos. 2458.34

sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and suitable for

operation on single phase 240 V,50Hz. having characteristic of quick action & tripping

with all advance feature & do not incorporate any electronic component. for following

Max. rating erected as directed

(ii) 40Amps. DP Cat. III

197 Supplying & erecting approved make Electronics Starter and relay for air conditioners 6.00 Nos. 975.66

in ABS plastic moulded housing. Company fabricated with bakelite terminal for

connection with silver coating bimetallic contact in switching device for o/p with

following features.

(1) Low Voltage Protection below 130 V

(2) High Voltage protection above 270 V

(3) Overload protection for 2-5, 4-10, 8-14, 10-16, 14-22 Amp. (inverse time chara-)

(4) Indicating LEDs for AC on LV, HV, O/L, T/D

(5) With unique feature of 3 minute of time delay

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

198 Providing and erecting metallic vitrified danger notice board as per language suggested 4.00 Nos. 69.69

by engineer incharge for MEDIUM VOLTAGE installation to be erected as per IS-2551.

199 Providing and erecting Annealed bare Copper wire 4.064mm to 1.626mm. 10.00 Kg. 794.87

200 Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. dia. 8.00 Nos. 368.65

galvanised iron pipe with coupling and buch buried in specially prepared earth pit

complete with necessary 8 SWG earth wire.

201 For using salt and charcoal / coke as required for pipe type earthing. 8.00 Nos. 171.70

202 Supplying & erecting earth pit of minimum bore dia.150mm size approved make 3.00 Nos. 4591.46

Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of

corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200

Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising,

connection terminal dia of 12mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable for following type of

applications with chamber and heavy duty cover. (A)(approved make OEM has to

submit test certificate including value of earth resistance of installation duly stamped

and signed by agency and officer Incharge has to ensure the value of earthing resistane

mentioned in test Certificate) & having back filling compound of (B) Inner chemical

(CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage

drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill Compound :-

Earthing compound should be capable to retain moisture for long time Necessary test

report must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

203 Providing & erecting weather proof, dust & vermin proof, floor mounted front operated

indoor type cubical panel board necessary IP-42 and above protection as per approval

from engineer incharge made from 14 SWG thick CRC M.S. sheet for outer body &

doors, 16 SWG thick CRC M.S.sheet for internal partitions with necessary accesories

supporting angles/ flats channel including cutting, bending, drilling, welding, riveting

with internal partitions & cable alley as per requirements & instruction of engineer-in-

charge with erection of

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

supplied switch gears, BUSBARS, suitable size of inter connecting PVC copper wire /

copper-aluminium strips, rubber grommets, rib, bakelite control fuses/MCB for

measuring instruments, earth bus & earth bolts, foundation flange - bolts-base Plates,

sufficient nos. of hinged doors, handles with locking arrangement and rubber

gasket,heavy duty end terminal connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be painted with epoxy powder

(The rates excludes the cost of switchgears, bus bars, inter connecting mains & Copper

Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding base

beams) The panel shall be supplied with following approved manufacturers with

following size.

(A) locally fabricated panel board (i) with 350 mm depth 4.50 Sq.Mt 10468.65

204 Providing , erecting , fabricating the M.S. structure as per requirement on site 105.00 Kgs. 77.77

incorporating proper size of M.S. angles,square,round, flats, bars, channels, sections

complete with cutting, welding, grinding & finishing duly painted with one coat of red

oxide with erection on site as per direction of engineer in charge with necessary

grouting, cementing, plastering & finishing complete.

205 Providing and erecting FRLS XLPE(IS:7098)(I)-88 ISI armoured cable multistrand

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables

(D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core) 30.00 Mtr. 454.50

(E) 3 1/2 core 95 Sq. mm ( 50 Sq. mm 1/2 core) 95.00 Mtr. 589.84

206 Providing and erecting FRLS XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / 420.00 Mtr. 151.50

Solid Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables

(B) 4 core 6 Sq. mm

207 Making trench in soft soil of suitable width of 90 cm deep for laying cable or locating 205.00 Mtr. 55.55

the fault all over the run and back filling the same and making the surface as normal

208 Drilling the road without breaking the road surface (Asphalt) for laying of cable for 10.00 Mtr. 492.88

feeding power supply by making up to following size of holes at both ends complete.(A)

Up to 100 mm bore dia

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

209 Providing & laying approved make Double walled corrugated pipes (DWC) of 210.00 Mtr. 62.62

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of

same material at required depth in existing trench for laying of cable. below ground /

road surface for enclosing cable (A)50 mm outer dia

(C))90 mm outer dia 80.00 Mtr. 95.95

210 Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC 36.00 Nos. 38.38

insulated armoured cable complete with out going tails, insulating tape etc for

following size of cables.(B) 2 to 4 core 6 Sq. mm

211 Providing and, fixing heavy duty flange type brass double compression type cable

gland with rubber ring for PVC insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables.

212 Solder less crimping type Aluminium lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an approved manner.

213 Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with double 75.00 Nos. 1948.29

ball bearing ISI mark with Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete

having 3blades with aluminium blades with , canopy & 30 cm. down rod erected with

earthing.(Make shall be approved by Engineer in charge))

214 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod 75.00 Mtr. 108.07

erected duly painted for fan complete with proper insulation without leakage and

215 Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars 75.00 Nos. 108.07

up to 50mm length each side and pierced through a 16 Gauge M.S. box / Heavy Duty

PVC box complete erected concealed in Ceiling with necessary finishing.

216 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box. 75.00 Nos. 18.18

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

217 Supplying & erecting approved make low noise decorative exhaust fan having square 18.00 Nos. 1703.87

frame ABS body with inbuilt lowers & square frame

250mm with 1350 RPM Cat.II

218 Supplying and erecting approved make Octagonal pole made from HR sheet steel. The 11.00 Nos. 7561.87

pole should be made as per IS. and shall be coated with hot dip galvanizing as per IS

2629/2633/4759, suitable suspend local wind speed with integral Junction box consist

of terminal plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-Rail for

MCB Mounting, stud type terminal and arrangement for cable termination to be

erected With Suitable foundation (Included) as per details given by manufacturer

considering site requirement.

(C) 5 Mtr. Long 70 mm Top X 130 mm bottom dia, 3 mm thickness with

200mmX200mmX12mm base plate, 4-M16 Bolts and 600mm long with necessary G.I. J

Bolts .Approx Pole weight 46 kg

219 Supplying & erecting approved make SMC press moulded composite FRP. loop-in, 8.00 Nos. 515.10

loop-out approx. 2mm thick box complete with Bakelite connector strip

5way(3P+N+E),DIN rail for mounting mob & hinged doors as per requirement having

locking arrangements with mounting clamp with nuts, bolts & washers suitable for

erection on pole with cable clamps& earth bolt of following size of box.

(B) 250mm x 200mm x 100mm [deep]

220 Supplying and erecting Street light pole bracket comprising main B Class GI pipe of 4.2 0.00 0.00 0.00

cm/require outside dia. complete with suitable B Class G.I. sleeve tubing of approx.

45cms.length and suitable for 76.5mm/80mm/require size of pole top having nuts and

bolts for fixing the brackets and having spread of 0.5 mtr. Length with 110 deg.with

vertical plane and suitable welded stiffener reducer and nipple with check nut

complete painted with one coat.of Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of arms.

[B] Double Arm Bracket 0.5 Mtr 8.00 Nos. 622.16

221 Supplying and erecting B class Galvanized iron pipe having smooth finished bore of the 8.00 Mtr. 215.13

pipe on both ends erected nuts and bolts along the pole / wall shaping the pipe as per

site requirement. Pipe dia as following.(B) 32 mm dia

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

222 Supplying & erecting IP 55 grade following size section pillar fabricated from joint less 1.00 Nos. 3595.60

M.S. Sheet with angle iron legs made from jointless M.S. Angle with cable clamps to be

buried in ground to have appropriate erection to work uniform until erected with

cement concrete foundation and 45 cm high bricks work finishing with plaster etc.

hinged double door internally supported on both side, with internal and outside

looking arrangement with look and keys in duplicate 35 x 35 x 5 mm M.S. Angle of Two

Nos. one is welded and other with nut and bolt for erecting Bakelite sheet. Painting the

Section Pillar inside and out side with three tank powder coated paint. section pillar

roof should be without joint with water leakage proof & tested as per IP 55 test &

followed by IS 2147 of

(B) 75 X 60 X 45 cm section pillar fabricated from 16 Gauge MS Sheet with angle iron

legs 45 cm long made from 35 X 35 X 5 mm thick MS angle.

223 Supplying and erecting HYLAM sheet on existing angle iron frame.for following 0.30 Sq 1541.27

thickness(D) 8mm mtr

224 Supplying & erecting approved make Digital time switch having lithium cell 6 years 1.00 Nos. 3168.37

operative and operate battery backup 1 channel day clock with 14 memory

programme, suitable to operate on 240V + 5%, 16A with, floating contacts Minimum

switching setup time 1 minimum & LCD display. Also comprised permanent ON/OFF

switching. Programming switches & housed in fire proof thermoplastic enclosure &

transparent cover erected as required with necessary connection erected as directed.

225 Supplying & erecting power contactor ,AC3 duty for time switch complete erected as 1.00 Nos. 2782.55

per direction Cat III (D) 4 pole 440V 40 Amp.

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

226 SITC of Digital / PCM / TDM EPABX System having SMT design, system with flexible

universal slots. Inbuilt Auto attendant facility, Minimum 15 Nos. conference, Analog

extension line, Calling GSM, E&M line, PRI / EI & VOIP program me through Analog

telephone digital key from Ethernet, public address cord, shall have unrestricted

simultaneous dialing facility,

QSIG protocol on PRI, 95 / STD / ISD / Local-Locking, Class of Service, Quick Dial-Single

Digit dialing of any two external number, Once only ring device, Chairman / Secretary -

Do not disturb Facility, Power Down Mode, Hot Line, Hot Outward Dialing, Day Night

Mode, Auto Call Back, Barge-in, Call Pick Up & Call Transfer, Call transfer while Ringing

with Voice Guide System, (DISA), Caller ID (CLI), CLI Base ECF, CLI Base routing

Internet Ready Port, External Music Port, Call Budgeting, Call Most Calculation

(ASMDR), DID Direct Inverse Dialing, External Music Input, Fax Homing, Global

Directory Printing with following capacities [[Approved by Competent Authority i.e. not

Below the rank of Executive Engineer ]

[B] No of Extension 24, No of Junctions 9, 8 Port IP Resource in-built, 4 Port Web base 1.00 Nos. 51440.31

Video Conferencing, No of expandable ports : 96, Operators Console - 01 Compatible :

227 Supplying & erecting push button type telephone instrument having speaker phone 18.00 Nos. 565.60

Caller ID & hands free dialing system & 30 memories with display system Single line

[[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

228 Supplying & erecting Single line push button type Two way Cord Less telephone 1.00 Nos. 5565.10

instrument Speaker Phone having feather light key pad 30 days standby battery life,

hands free speaker phone, 19 station speed dialler, inter com with 2 way paging & lock

key one touch dialler. [[Approved by Competent Authority i.e. not Below the rank of

Executive Engineer ]

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

229 Supplying & erecting Amplifier having following specification: 1.00 Nos. 13558.24

Power Output :250W (RMS) (300W Max.)

inputs : 6 Misc. & 2 Aux.

frequency Response :50-1500HZ I3db

Tone Controls :Cut & Boost type

LED Meter :5 LED Arrays

The amplifier suitable to operate 240V A.C.& 24volt D.C. (Battery) with automatic

changeover from AC to Battery operation, duly protected by wrong Battery Polarity

connections. [[Approved by Competent Authority i.e. not Below the rank of Executive

230 Supplying & erecting four channel Echo Mixer Pre-amplifier with following 1.00 Nos. 4314.72

(i) Suitable to operate on 24OV.A.C. & 12 V D.C. Battery supply

(ii) B.B.D. Delay system ECHO facility on all inputs through ECHO volume, Repeat &

(iii) Peak LED for setting optimum distortion free input levels

(iv) Two outputs, variable for line & fixed for recording

(v)Compatible with Audio Mixing consoles. [[Approved by Competent Authority i.e. not

Below the rank of Executive Engineer ]

231 Supplying and erecting Weather & Dust resistant sound column with Aluminium case & 2.00 Nos. 2466.42

Aluminium mesh grille with foam layer under grill, rotary- switch for selecting power

taps / impedance having frequency response 150-20000 Hz with following

specifications . [[Approved by Competent Authority i.e. not Below the rank of Executive

(a) With 4 speakers, capacity of power handling 45W (MAX) & 30 W RMS, each

speaker have impedance of respectively 300 ohms / 30 W, 500ohms/20W,I -

K.ohms/10 W, 2K. ohms / 5W.

232 Supplying, Installing & testing approved make highly sensitive microphone capable to 1.00 Nos. 2740.13

pick up weak sound from longer distance & wider area suitable for stage shows, group

singing with frequency response 50 - 16000 Hz. Having sensitivity of 1.6MV / Pa &

impedance 250 ohms (Lo -Z), Supplied with quick detachable holder & 10 mtr.

twin core cable & 3 pin XLR connector. [[Approved by Competent Authority i.e. not

Below the rank of Executive Engineer ]

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

233 Supplying microphones stands with sturdy mechanism, treble free movement & 1.00 Nos. 257.55

positioning of microphones, free from rust with superior quality of chrome plating with

following size. [[Approved by Competent Authority i.e. not Below the rank of Executive

(b) Fixed height 35 cm & extendable up to 53 cm, with round base of dia. 16 cms.

234 Supplying & testing wireless microphone system for 92.5 MHz FM operation With 1.00 Nos. 1884.66

effective range 200 feet with microphone having facility for frequency adjustment &

receiver with LED indicator Telescopic antenna with battery cells.[[Approved by

Competent Authority i.e. not Below the rank of Executive Engineer ]

235 Providing and erecting approved make split air-conditioning unit consisting of copper 6.00 Nos. 50917.13

condensing unit with fan motor, hermetically sealed rotary compressor with

accessories etc. duly connected separately erected evaporating unit and blower motor

with its accessories by means of extra supplied proper insulated copper tubing,drain

PVC pipes suitable for ( cost includes powder coated Stand, Eco Friendly green gas

charging, 15A plug top & Remote Control) with necessary core cutting.

(1)For ISEER Range (KWH/KWH)(3.1 to 3.99)

(c) for 2 ton capacity

236 Supplying and erecting insulated pair of soft copper tubing open or concealed including 30.00 Rmt 1158.47

power and control cable,necessary PVC drain pipes for Split/Cassette AC machine up

to 4 TR capacity

237 Providing & erecting water cooler having storage capacity 150 Ltr. & cooling capacity 2.00 Nos. 61482.74

150 Ltr.per hour @ an ambient temp of 45˚ C. The outlet temp. of the water should

drop by 15˚C within a hour, The water cooler should be comprising of hermetically

sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating,

coil, thermostats, relay etc.complete with necessary inlet & outlet connection. The body

of water cooler will be made from Stainless Steel.

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

238 Supplying & erecting reverse osmosis (RO) water purification system with M.S. 2.00 Nos. 77891.20

powder coated pedestal frame, prefilter housing carbon filter suitable buster DC pump,

auto low & high pressure switches with following size of LPH capacity & erected as

[D] 100 LPH with 1 phase / 3 phase Raw water pump of 500LPH @ 2.5kg/cm2 - (1N0 -

Kirloskar /CRI/Lubi), Dual media filter 10"x54" - (1 No), Micron cartridge filter 20" x

2.5" ( 1No), High pressure pump 500LPH @ 10kg/cm2 - (1No - Shimge /CRI /Lubi),

RO Membrane housing with RO membrane of 40*40 - (1No), RO pressure tube 4" x 1E -

( 1No), 0 - 1200LPH Rotameter -(2 Nos), with Recovery Rate 50%.

239 Supplying and erecting approved make panel mounting type Digital Voltmeter having 3.00 Nos. 1275.63

3 digits LED display, 0 to 750 AC Volts range erected on existing panel board with all

connection, wiring etc .with manufacturers calibration certificate.

240 Supplying and erecting approved make panel mounting type Digital Ammeter having 3 3.00 Nos. 1558.43

digits LED display, external CT operated, calibrated for 0 to 1000 Amps suitable to

operate on 500 Volt AC , erected on existing panel board with all connection, wiring etc

.with manufacturers calibration certificate.

241 Supplying and erecting Ammeter / Voltmeter selector switch for 3 phase AC Supply 6.00 Nos. 317.14

500 V on existing panel board with necessary connections.

242 Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 ratio 9.00 Nos. 274.72

15 VA burden erected in existing CRCA box duly secured with insulating materials

connected to the meter

243 Supplying and erecting approved make suitable panel indicator LED type lamp, lens 9.00 Nos. 43.43

cover, complete erected with necessary connections.

244 Providing & erecting open well horizontal mono block pump set with cast iron body,

complete for three phase submersible motor having

[C] For 3 HP 3 phase open well horizontal mono block pump set suitable for 85 LPM to 2.00 Nos. 17279.08

270 LPM @ 11 mtr to 33 mtr head suitable for 50/65 mm dia delivery pipe Cat.II

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

245 Supplying & erecting approved make motor control cubical panel [Star delta] made 2.00 Nos. 7250.79

from 16G CRCA sheet duly epoxy powder painted inside and outside with hinged doors

and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital

volt and current meter (in a single unit) with micro controller based control unit and

current sensing single phasing preventer electronic overload protection, over voltage

(Programmable) protection and under voltage (Programmable) protection, prod less

dry run protection programming facility for setting of all parameter like overload

current, high voltage limit, low voltage limit, dry run limit with digital indication on

seven segment LED display for any fault like over load, high voltage, low voltage, dry

running single crimped, electronic star delta timer, feather touch start / stop push

buttons to be erected on angle iron frame. Grouted on wall the contactors will be of L&

T, Siemens, BCH make only)(A) DOL up to 5.0 H.P.

246 Lowering of submersible motor pump set at the depth of following ,complete with 2.00 Job 856.48

required. Nos. and size of casing pipes erected by means of proper chain pulley block &

pipe wrenches after checking of threads of each pipe with coupling to take the load of

the pump set and pipe assembly filled up with water (d)For Open well Horizontal

submersible pump set for sump well (i) 1 HP to 5 HP

247 Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible 30.00 Mtr. 104.03

Submersible copper cable approved make of following Size. (B) 3 Core x 2.5 Sq. mm.

248 Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using 2.00 Nos. 189.88

insulating material, water proofing material, & making the joint complete. (A) Up to

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

249 Supply, Installation, Testing & Commissioning of following size of Grid Tied Solar

Power Plant with

Solar Panels (ALMM approved): Frame Material : Anodized Aluminum alloy Frame

With Twin Wall Profile, Front Cover : High Transmission Low-Iron Tempered Glass (AR

Coated), High efficency and positive power tolerance Pmax: 0/+5, Module Efficiency

should be approx. 19.5%-22%, Normal operating temperature 45'C, Junction Box with

Waterproof IP67 & MC4 Compatible and Enclosed with Bypass diodes, 100%

Electroluminescence test to ensure error free Modules, Thep. temp. co-efficient of the

PV module shall equal or better than -0.45%/degree C. Solar PV modules of minimum

fill factor 75% to be used. Unit Production:- More than 4.5 Unit /kw /day

(Actual)(1Year Avg) With 10 year Product warranty. Modules must be complied to the

DCR(Domestic content requirements). The Ration of AC to DC is 5:6 for the Installation

capacity which are given in AC KW.

Solar Inverter: MPPT Range: MPPT Range: 80-1000 V , Max efficiency: 97.5% - 98.9%,

O/p Frequency: 50/60Hz, Operating Altitude (m) ≤4000, O/p Power Factor: ~1, O/P

THDi: <3%, Operating Tempreture Range: -25~60°C, Integrated protection of Inverter

are Anti-islanding Protection, Input Reverse Polarity Protection, Insulation Resistor

Detection, Ground fault protection, Residual Current Monitoring Unit, Output Over

Current Protection, Output Short Circuit Protection, Output Over Voltage Protection, PV

array string fault Protection. Protection Degree: IP65, User Interface LCD & APP,

Datalogger & Communication: GPRS / Wi-Fi.

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

Integrated, Input Reverse Polarity Protection Integrated, Insulation Resistor Detection

Integrated, Residual Current Monitoring Unit Integrated, Output Over Current

Protection Integrated, Output Short Circuit Protection Integrated, Output Over Voltage

Protection Integrated, Protection Degree: IP65, User Interface LCD & APP,Datalogger &

Communication: GPRS / Wi-Fi, Module Mounting Structure: The mounting (Rectangular

pipe / square pipe / circular pipe) with requisite cross bars, nuts and bolts, etc. shall be

Hot deep galvanized with minimum 80micron coating. The Rectangular / square

/circular hollow pipe section used for the structure should have a minimum thickness

of 2.0 mm. other than above, the material thickness should be minimum 2.5 mm. A

certificate of a structural engineer certifying the strength and stability of the mounting

structure to withstand the weight and wind speed of 150 km/hour , shall be submitted

by the vendors. Hot Dipped Galvanized steel coils. suitable arrangement for base plate

for foundation , solar panel mounting, the structure should be suitable for carry the

load of solar panel,wiring, sprinkler system etc. with necessary foundation work/wall

mount, j bolt, anchor fastner etc. the nut bolt used for installtion of stucture should be

(SS 304) quality.The ground clearance of the bottom most edge of solar panel shall not

be less than 300 mm to 1200 mm or as per site’s technical/feasibility requirement.

a. Column –The minimum section (thickness) should be 60MM*40MM

b. Rafter - The minimum section (thickness) should be 60MM*40MM

c. Purlin - The minimum section (thickness) should be 40MM * 40MM Balane of System

with necessary Swichgears (Suitabel size and protection of ACDB & DCDB), inter

connecting wiring, earthing system as per the CEIG drawing approval,

lightining arrester system as per the CEIG drawing approval, all liasoning work with

various gov. dipartment like state nodal agency,DISCOM & CEIG is included in agency

scope (Excluding All charges namely GEDA Application fees, Solar connectivity

Charges, Meter connectivity Charges, Meter testing Charges and system

stability/strenthning charges.)

Item No. Description of Item Quantity Unit Rate Total Amount

Item No. Description of Item Quantity Unit Rate Total Amount

(C ) Grid Tied Solar Power System: 11 - 25 kW (3 - phase) 25.00 Kw 42455.35

Rupees Three Crores Sixty Five Lakhs Seven Thousand Four Hundred Sixty Four and Paise Eighty Two Only

I / we, am / are willing to carry out the works at______ % Above / below percent (should be written in figure and words) of the estimate

rates mentioned above.

Amount of my /our tender works out as under.

Estimated amount put to tender: Estimated amount put to tender:

Deduct………% below Add………% Above

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge for which no extra

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills.

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017 Cement

Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a change as per actual mix design the cost of

difference of cement consumption have been deducted from the rate of original item at the rate of input rate mentioned in all the tender.

Quantity, rates & wording of items are as per estimates and calculation in the "Bill Of Quantities" are arithmetically checked and found

Signature of Contractor

Deputy Executive Engineer Executive Engineer

(P) R. & B. Sub Division (P) R. & B. Division

Kheralu Mehsana