PROVN OF ONE TOILET BLOCK NEAR HQ AND P BTY (OR LIVING) IN 116 MED REGT AT MIL STATION DHRANGADHRA UNDER GE(A) GANDHINAGAR

Amount

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard and dense soil complete all as specified and directed.

Excavation in trenches n.exc 1.50mtr wide and n.exc 1.50mtr in depth for foundation etc or for shaft, wells,cesspits, manholes, piers holes etc not exc 10 sqm on plan and and getting out in soft/disintegrated rock all as specified and directed.

M&L cement concrete (1:4:8) type D-2 using 40mm graded agg as in foundations, filling and mass concrete all as specified and directed.

Returning filling in,including spreading levelling, watering and well ramming in layers not exe 25 cm.in soft/disintegrated rock completed as specified and directed.

Removing excavated material soil exc 500m but not exc 1.00Km and depositing where directed at a level n. exc. 1.5 m above the starting point.

M&L for moorum/red bajri filling in floors or pavings, laid in layers n exc 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for 75mm thick cement concrete type D-2, 1:2:4 (40mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for walling of random rubble stone masonry, uncoursed, brought upto courses, well bonded, bedded and solidly hearted, built in CM (1:6) complete all as specified and directed.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface n. exc 20mm for sand stone and dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses completed as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

M&L for reinforced cement concrete, M-25(Design mix) in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns, etc basement slabs and mass concrete complete including form work all as specified and directed.

M&L for reinforced cement concrete M-25 (Design mix) (20mm graded stone aggregate) as in beams, cantilevers, bressumers, lintels over 1.5m span complete including form work all as specified and directed.

M&L for reinforced cement concrete M-25 (Design mix) (20mm graded stone aggregate) as in chajjas complete including form work all as specified and directed.

M&L for TMT 10 mm dia bar and over, cut to length, bent to shape required, including cranking, bending, hooking ends, binding with and inlcuding mild steel wire (annealed) not less than steel wire 0.9mm dia or securing with clips complete all as specified and directed.

S&F Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length bent to shape required and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for rendering 15mm thick cement plaster in cement mortar 1:4 on stone Masonary surfaces or surface other than fair face of brick work is to be finished even and smooth w/o using extra cement completed as specified and directed.

M&L for rendering 15mm thick cement plaster in cement mortar 1:6 on stone masonary surfaces or surface other than fair face of brick work is to be finished even and smooth w/o using extra cement completed as specified and directed.

M&L preparation of new surfaces of plastered or unplastered of wall and application of three coat of white washing.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white cement primer complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size 300 x 200 x 7mm thick on vertical surfaces such as skirting/dado, in two different colours, set and jointed in neat cement slurry and pointed in coloured cement to match laid over and including rendering 10mm thick in cement mortar (1:4) complete all as specified and directed.

M&L for Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc. in two different colours, set & jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

S&F, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specifications complete all as specified and directed.

S&F, MS angle iron framed work as in doors or gates of angle or other section conforming to Fe 290(Gde E-165) with gusset plates, rails, braces, etc complete including hanging also fastening and fixing complete as specified and directed.

S&F 35 mm thick, 2nd class hard wood factory made, plain, framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S&F, 300mm length of bolt aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cost or extraded sections and fixing bolts and sliding bolts of extraded sections or cost aluminium alloy.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed

S&F, butt hinges, medium weight, cold rolled, mild steel of size 100 mm complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

S&F, factory made steel windows with side hung shutter including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded including applying one shop coat of red oxide primer complete all as specified and directed.

S&F, factory made steel windows with side hung shutter including box type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded including applying one shop coat of red oxide primer complete all as specified and directed.

S&F factory made steel ventilators with top hung shutter including hinges, steel peg stay, glazing bars including applying one shop coat of red oxide primer all as specified and directed

M&L for mild steel rolled sections (Fe 410-W (Gde-E-250) quality-A) as in post, main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all specified and directed.

S&F, pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F, pre-painted galvalume aluminium zinc coating GI based plain steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F false ceiling, at any height, 600 x 600mm grid with Armstrong 'Prelude XL 32' grid system and 16mm thick mineral fibre acoustic tile 'RH - 99 Classic lite' with suspension system complete all as specified and per manufacturer's instruction. Make : Armstrong or equivalent as approved by GE.

M&L for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc. 0.5 sq.m in each pane complete all as specified and directed.

M&L for 3mm thick figured glass, pin headed type and glazing with oil putty in square not exc. 0.5sq.m in each pane complete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 25mm bore of pipe complete all as specified and directed.

Supply, hoisting, fixing in position and connecting 1000 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top), ISI marked, including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I complete all as specified and directed.

S&F 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed. (Minimum weight -210 Gms)

S&F Vitreous China half urinals bowl type (back to corner wall type), complete including providing and fixing plug, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; flush pipe, grating, spreader with pipe and union for discharge pipe.

S&F vitreous china wash basin, white, flat back of size 550mm x 400mm including brackets grouted in cement mortar 1:2 in wall complete all as specified and directed. Note :- Supply only pillar taps, waste fittings, PVC connection, PVC waste pipe shall be measured and paid separately.

S&F vitreous china squatting pan, 'Orissa’ pattern, white of size 580mm x 440mm with integral foot rest, P or S trap (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F vitreous china wash down closet pan (pedestal pattern) of white (excluding flushing cistern and flush pipe) but incluging connection to drain pipe or outgoing pipe and to flushing pipe, antisyphonage pipe, seat and cover etc complete all as specified.

S&F 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, inlet ball valve, float and handle including brackets and connection to pipe or lever etc. complete all as specified and directed.

S&F, chromium plated over head shower 125mm size with or without swivel joints, including fixing to pipe or union complete all as specified and directed.

M&L for 50mm thick cement concrete 1:3:6 type C1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L for soap dish, vitreous china white, approximate size 160x160x90mm complete all as specified and directed.

S&F 40mm bore, low density polyethelene pipe (HDPE) of pressure rating 6kgf/sq.cm fixed to walls, ceilings or in floors etc. complete all as specified and directed.

S&F waste coupling of PTMT (half or full threaded) suitable for urinals 32mm dia (Minimum weight 32mm) complete all as specified and directed.

S&F, 32mm bore, low density polyethelene pipe (HDPE) of pressure rating 6kgf/sq.cm fixed to walls, ceilings or in floors etc. complete all as specified and directed.

S&F bib taps, cast copper alloy, fancy type, chromium plated, screwed down, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed.

S&F stop valves, fancy type, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed.

Supply only Pillar taps cast copper alloy with capstan head, chromium plated, fancy type screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

Supply only PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F, 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or floor complete all as specified and directed.

S&F, 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or floor complete all as specified and directed.

S&F, 75mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed.

S&F PVC (SWR) junction single, (single T) equal or unequal with access door of 75mm bore.

S&F PVC (SWR) junction single, (single T) equal or unequal with access door of 100mm bore.

S&F, 110mm bore PVC (SWR), vent cowl complete all as specified and directed.

S&F PVC (SWR) nahani trap, with chromium plated grating including jointing with solvent cement, dia of outlet 75mm complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed.

M&L for cement concrete (1:3:6), type C-1, using 20mm graded stone aggregate in coping and the like including weathering, slightly rounded or chamfered angles and throating, Including necessary form work complete all as specified and directed.

M&L for concrete bed to drain pipes 1:3:6, type C-2 (using 40mm graded crushed stone aggregate) including packing under, and haunching against the side of pipes after they are laid and tested for 150mm internal dia of pipe.

M&L for salt glazed stone ware (SGSW) drain pipes laid in tenches and jointed specified in size of pipe is Grade 'A' 150 mm internal dia of pipe.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick or concrete surface and finished the surface even and smooth without using extra cement mixed with water proofing compound complete all as specified and directed.(WPC shall measured and paid separately)

Supply only integral water proofing compound.

M&L for 60mm thick Machine pressed precast concrete interlocking paver with grey cement and pigment any shape including 25mm sand as screed bed and size conforming to IS 15658-2006, M-25 grade.

M&L for factory made Pre-cast cement concrete kerb stone masonry type B-1, 1:2:4 (20mm graded stone aggregate) with solid block exc 10cm and set in CM 1:6.

Cutting into existing manholes for connecting new drain pipes, making good to pipes and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cment concrete (1:2:4) type B1, using 20mm graded stone aggregate, smooth finished and reforming benching as required for 150mm bore of pipe complete all as specified and directed.

M&L pre-cast reinforced cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate for manhole covers including placing the cover in position and set in cement mortar (1:6) complete all as specified and directed. Note: Reinforcement shall be measured and paid seperately.

M&L for mild steel TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M & L for wring with and including multistranded copper conductor 1.5 sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 volts grade, ISI marked with valied CML number drawn in and including medium grade PVC casing and capping double lock type 32mm in size, fire resistant, ISI marked including with its fittings and fixture such as tees, bends, elbows, junction boxes, etc. Including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) Single , core PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. Complete all as specified and directed for the following:-

(a) One light/fan point controlled by one switch

S &F, switch piano, flush button, single pole , one way 5 Amps complete all as specified and directed.

S &F, sheet metal distribution board, SPN 4 way 240 volt, double door factory made and tested complete, protection class IP-42 suitable for mounting MCBs, isolator with 200 A tinned copper bus bar complete all as specified and directed

S & F, ceiling rose, 3 terminal , any shade, of PVC/Polycarbonate, isolated body complete all as specified and directed.

Supplying & laying, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire heavy duty underground cable with aluminium multi stranded conductor , 1100 volt grade, laid in trenches/duct, passing through pipe/ duct or fixed on pole and connecting and testing complete all as specified and directed of 25 sqmm, 4 core size of cable.

S & F, 1X9 watts, bulk head luminaries deep drawn anodised body, epoxy white powder coated, heat resistant, prisamatic glass cover with specially designed gasket, including CFL lamp 9 watt and connecting up with twin core twisted flexible copper cable of suitable size and testing on completion all as specified and directed, As per Cat No BJBE 19 of Make:- Bajaj or equivalent make approved by GE from the make specified in Appx ‘C’.

S & F LED light fitting, batten type house in extruded from powder coasted minimum, 9 watt for soft diffuser lighting with and including lamp and connecting up complete with PVC insulated and PVC sheathed round flexible three core copper conductor cable suitable size and testing on completion all as specified and directed. Make as per Cat No BAJAJ LED BATTEN 9w (item code 830102) of Bajaj of equivalent make approved by GE from the make specified in list of make

S & F LED tube light fitting, 20 watt including LED tube 20 watt including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Make of fitting havells or equivalent make approved by GE from the make specified in list of make

S & F, Exhaust Fan, 300 mm Sweep single phase, 230 volts, 50Hz including making opening for exhaust fan including grouting nut, bolts and washer for fixing of fan and making good the disturbed surfaces all as per existing and mounting fan including connected with three core copper conductor cable 0.75mm complete all as specified and directed.

S & F miniature circuit breakers, type curve ‘B’ 10 KA, SP, 6 to 32 Amps complete all as specified and directed.

S & F isolator, single pole and neutral, type curve ‘C’ 10 KA, 40 amps 230 Volts complete all as specified and directed.

S & F sub main wiring with 2 single core, 4 sqmm PVC insulated, unsheathed 1100volts grade, FRLS, copper multi stranded conductor drawn in and including PVC concealed conduit and conduit accessories including drawing one run of PVC insulated, unsheathed, 100, Volts grade FRLS copper conductor multi stranded, 2.5 sqmm size as continuous earth wire drawn through and connected to main switch/DB and testing on completion complete all as specified and directed Note: (i) 2 runs of main conductor, one run of earth conductor and one run of PVC conduit and accessories shall be measured as one unit length. (ii) Rate quoted shall deemed to including cuttings chases for concealing PVC conduit and making good the disturbed surfaces in CM 1.3 complete

M & L Earthling complete with galvanized steel earth plate electrode of 60 cm X 60 cm X6 mm thick buried directly in ground earth pit not less than 2.25 mere deep below normal ground level with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth wire 4 mm dia by means of points nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No 3 of MES SSR Part I all as specified and testing on completion including provision of earth load protected by 15mm dia light grade GI pipe & watering pipe shall be 20mm bore medium grade GI pope including all excavation and earth work in any type of soil, PCC pit with RCC cover, char coal, salt funnel etc complete Note: Rate quoted by tenders shall be deemed to included for following provisions :- (i) Excavation & earth work in any type of soil including removing of surplus material upto 50 m (ii) PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50X50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles (iii) Main earthing lead from earth electrode to test point upto 7.5 mtr (iv) Funnel with watering pipe GI Pipe 20 mm bore ISI marked medium grade & copper lugs, charcoal & salt as reqd (v) GI protection pipe size 15 mm bore light grade 7.5m all as directed.

partechengineers

Singh Engineer And Contractor

SNEH TRADERS