Construction Work of Twon Hall, At Final T.P.S.No. 01 Bharuch, O.P.No. 09, At. Bharuch Dist. Bharuch, Under Swarnim Jayanti Mukhyamantri Shaheri Vikas Yojna (Unique Identity) Year-2025-26.

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials and disposing off the excavated stuff upto all lead. (B) Dense or Hard soil

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful materials and disposing off the excavated stuff upto all lead. (C) Hard Murrum

Supplying of Rubble materials. Lead 45 Km.

Filling in plinth with sand under floors including watering ramming, consolidating and dressing complete.

Spreading the stone aggregate for rolling and W.B.M. including filling the interstices to required camber and gradient (excluding spreading of Blindage)(ii) 40mm to 63mm size aggreagates (H.B.)

Providing and laying in position Ready Mixed M-150 grade concrete for reinforced cement conctere work (A) Foundation and Plinth, using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering shuttering finishing and reinforcementincluding cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained)

Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating each disposited layer by ramming and watering.

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Foundation footing (A) Foundation footing base of column and mass concrete, using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained)

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Beam (C) Slabs, Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two level., using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) G.F. Level

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Beam (C) Slabs, Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two level., using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) F.F. Level

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Beam (C) Slabs, Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two level., using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) S.F. Level

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Lintel (C) Slabs, Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two level, using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) GF. Lintel

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Lintel (C) Slabs, Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two level, using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) F.F. Lintel

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Lintel (C) Slabs, Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two level, using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) S.F. Lintel

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Chhajja (C) Slabs, Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two level, using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) G.F. Chhajja

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Chhajja (C) Slabs, Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two level, using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) S.F. Chhajja

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Column (D) Columns, Pillars posts and struts upto floor two level, using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) G.F. Column

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Column (D) Columns, Pillars posts and struts upto floor two level, using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) F.F. Column

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Column (D) Columns, Pillars posts and struts upto floor two level, using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) S.F. Column

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Slab (C) Slabs, Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two level, using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) G.F. Slab

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Slab (C) Slabs, Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two level, using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) F.F. Slab

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Slab (C) Slabs, Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two level, using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) S.F. Slab

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Wall (B) Walls, from top of foundation level upto floor two level, using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) G.F.

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Stair Case (E) Staircases excluding landing up to floor two level, using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) G.F.

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement conctere work in Stair Case (E) Staircases excluding landing up to floor two level, using cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, including the cost of formwork like centering shuttering finishing but exculding cost of reinforcement and including cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS 456 shall be maintained) F.F.

Steel Reinforcement bars Supplying cutting, bending, binding and placing in position steel as per plan and design and as per ISS 2502 including cost of steel and binding wire for reservoirs/structures only including lift up to 6 meter height or depth below G.L. for all diameters Do-Corrosion resistance steel (CRS) Fe 500 grade for all diameters confirming to relevant I.S.

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement Mortar 1:5. (1- Cement : 5 -fine sand) (B) Conventional

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in Superstructure in Cement Mortar 1:5. (1- Cement : 5 -fine sand) Extra for brick work in superstructure above plinth level upto floor two level (B) Conventional

(i) Half brick masonary in common brunt clay building brick having crushing strength not lass than 35 Kg / Sqcm. in cement mortar 1:4 ( 1 cement : 4 coarse sand ) extra for brick work in superstructure above level up to floor two level (B) Conventional

Providing 15 mm thick cement plaster in single coat on fair side brick/concrete wall for interior plastering up to floor two level finished even and smooth in with Floating coat of neat cement. (i) cement Mortar 1:3 (1 cement : 3 Sand)

Providing 15 mm thick cement plaster in single coat on fair side brick/concrete wall for interior plastering up to floor two level finished even and smooth in (i) cement Mortar 1:3 (1 cement : 3 Sand)

Providing 10mm thick cement plaster in single coat on brick/concrete walls for interior plastering upto floor two level and finished even and smooth in (i) Cement mortar 1:3 (1-cement:3-sand) Extra over items 58 to 64 for finishing with a floating coat of neat cement slurry.

20mm thick sand faced cement plaster on walls upto height 10 metres above ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. complete.

Providing and laying Vitrified tiles 8 to 10 mm thick , 36'' x 36'' in flooring treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand ) finishing with flush pointing in white cement.

Providing and laying 18mm thick Black Granite stone slab flooring over 20mm (average)base of cement mortar 1:6 (1-cement : 6 coarse sand) or L.M. 1:1.5(1- lime putty : 1.5 - coarse sand) laid and jointed with gray cement slurry including rubbing and polishing complete. (A) 25mm thick Block Granite

Labour Charge Full Round Edge for Granite

Providing throating or plaster drip and moulding to R.C.C. Chhajja.

Providing and laying Vitrified tiles 8 to 10 mm thick , in skrting risers of steps and dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry.

Providing and laying broken chine mosaic flooring for terrace using 12 mm to 20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to plain or slope and to be tempered to bring mortar creme out upto surface using white cement including rounding off junctions and extending them upto 15 cm along the wall,clearing with water and oxalic acid etc. as directed.

Extra for providing and mixing water proofing material in Cement concrete in mix proportion recommended by the manufacturers.

Providing and laying cement concrete flooring 1:2:4 (1-cement : 2-coarse sand : 4-graded stone aggregate 20mm nominal size) laid in one layer and finished with a floating coat of neat cement. (B) 50mm thick.

Providing and fixing FRP frame size 125x65 mm and 35mm thick FRP shutter with wood grain raised panneled design finish shutter having extra reinforcement on sides & edges in Gel coat finish. The core of the shutter & frame is to be filed up with injected polyurethene foam done in situ alongwith embedded wooden pieces for stiffening & also taking hinges & fintures. The whole FRP frame & shutter is to be water proof weather proof, termite proof & resistance to mild acid/alkali. Rates are to be inclusive of S.S hinges with fastener sleeve & alluminium fixtures & fastenings.

Providing and fixing window having extruded aluminum DOMAL Colour anodized section frame main outer size as per required, horizontal two track member size as per required, vertical member of size as per required with sliding shutter & openable of horizontal member as per required, vertical member of size as per required with 5mm thick transparent bronze color tinted float glass & Bright Bar 12mm Jali with powder coated aluminium fitting and fixture and transparent silicon sealant glass fixing to frame as per details etc. complete for window

Providing and fixing standared extruded of alluminium section of size 63.50 x 38.10 x 1.95 mm(of Jindal Section no:4605,@ Wt 1.094Kg / Rmt with colour anodized alluminium frame with 5 mm thick transparent bronze colour tinted float glass as details etc complete for Fix window.

Providing and fixing standared extruded of alluminium section of size 63mm x 38.10mm x 1.2mm @ Wt. 0.643 Kg/mt with colour anodized alluminium frame for ventilation with 5 mm thick frosted glass as details etc complete for Ventilation

Providing and fixing 35mm thick Flush Door both side 1mm thick Laminate Fitting materials 304 Grade S.S. 4" Hinges, S.S. Handle, S.S. Stoper and Edge Side of Indian teakwood battens Patti, 15CM long S.S. Handle Fevico 998 and Door Closer Heavy Duty, S.S. Door Stopper and S.S. Door Stop, S.S. 25 Cm. long Door Aldrop and including of all type labour and necessary fitting material etc. Complete.

Item Description

Providing and fixing M.S. grills of required pattern to wooden frames of windows etc. with M.S. flats at required spacings and frame alround, square or round bars with Hollow Pipe round headed bolts and nuts or by screws (A) Plain Grill.

Applying general insecticide pest control treatment to floors, cupboards etc including labour materials etc. complete. Using Imidacloprid 30.5 SCas Per IS 6313 part -II( (0.075 Percentage concentration by mass) is recommended 10.5ml chemical diluted with 5 liters of water application 0.5 litre chemical /Sqm of surface is recommended as per I.S.

Providing and fixing in position collapsible steel shutters with vertical channels 20 x 10 x 2 mm braced with flat iron diagonals 20 x 5 mm size with top and bottom rails of T_rin 40x 40 x 6 mm with 38mm dia, steel pulleys complete with bolts, nuts, locking arrangements, stoppers handles including applying a priming coat of red lead paint.

Providing and fixing 12mm thick Toughened Glass Door, Top & Bottom Patch, Floor Door Closer, Both side Handle, lock including all labour, necessary fitting material, loading, unloading, transportation etc. complete etc. Complete.

Providing and fixing 4mm thick Alluminium Composite Pannel sheet and M.S. Pipe frame and including of screw, welding, and silicon tube and pressure tube and scaffolding charge and all lead & lift including of labour, materials loading, unloading, transportation etc. complete.

Providing and laying exterior 10 to 15mm thick stone Cladding work size of 300x300x dedo on & jointed with white cement slurry. Including of labour, unloading, loading, transportation etc. complete.

Supply, Application and Sealing of FF Calco Premia Wall renders, ~1.5 to 2.5mm thick in approved texture finish and colour, including manufacturer recommended sealing.

Providing and fixing 4mm thick CNC Laser Cutting Decorative Jali and Vertical and Hori. Post of 80x80mm Pipe and Black Powder Coated Including of welding, bending and all labour etc. Complete.

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jali of the following nominal diameter of self cleansing design with C.I scread down or hinged grating including the cost of cutting and making good the walls.

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps. (A) 100mm x 100mm size P type.

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(i) Inside dimensions 455mmx 610mm and 450mm deep for single pipe line.

Providing and fixing screw down bib taps of following size.(A) Brass screw down bib tap polished bright. (i) 15mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve.(D) 32mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve. (E) 40mm dia.

Providing and fixing water closet squatting Pan (Indian type W.C. Pan) size 580mm (Earthwork, bed concrete, foot reste and trap to be measured and paid for separately) (A) Vitreous China.(I) Long pattern White colour

Providing and fixing 100mm size P or S trap for water closet squatting pan including jointing the trap with the pan and soil pipe in cement Mortar 1:1 (1-Cement : 1-Fine sand) (A) Vitreous China.

Providing and fixing Urinal of approved quality including connection with trap and with integral longitudinal flush pipe. (A) Squating plate pattern white earthenware 550mm x 300mm.

Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S. brackets painted white including sutting holes and making good the same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm size. (i) In white colour.

Providing and fixing C.P. brass waste for washbasin or sink. (A) 32mm dia.

Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete.(i) 20mm dia.

Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet. (A) 100mm dia. Each

Providing erecting and fixing double coated ISI water tank of required capacity each with all necessary fittings and connection etc. complete on terrace

Providing and fixing brass screw down stop tap. (C) 25mm dia.

Providing and fixing wsh down water closet (European type, W.C. Pan) with integral P or S trap including jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and cover to be measured and paid for separately) (A) vitreous China Pattern :(i) in white colour

Providing and fixing plastic seat and cover for wash down water closer with C.P. brass hinges and rubber buffers. (B) Black plastic seal and cover.

Providing and fixing 600mm x 450mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and washers.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 32mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160 mm diametre x 210 mm length x 196 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing and supplying, Laying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint including cost of rings, Tess, beand, reducer etc. as per IS specification no. 4985/1988 including all local and central taxes, transportation,freight charges, octroi, inspection charges, loading, unloading, conveyance to the departmental stores and including cost of jointing meterial etc. complete. Test Pressure 6Kg/cm2 (90mm Dia.)

Description As Above 75mm Dia.

Applying priming coat over new steel and other metel surface after and including preparing the surface by throughly cleaning, oil,grease, dirt and other foreign matter and scoured with brushes fine steel wood, scrapers and sand paper with ready mixed priming paint brushing red lead.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint, brushing, interior to give an even shade including cleaning the surface an even shade including cleanicn the surface of all dirt, dust and other foreign matter.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth.

Wall Primer of Approved Brand

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an required shape even shade after thoroughly brushing the surface to remove all dirt, and remains of loose powdered materials.etc complete.

Steel work, welded in built up sections framed work including cutting, hoisting, fixing in position and applying a priming coat of read lead paint. (A) In beams and joists, channels angles Tees, flats, pipe etc with connecting plates or angle cleats as in main and cross beams. Hip and jack rafters, purlins conneted to common rafters and the like

Providing and fixing 0.90 mt height stainless (304 Grade) steel stair railling by top rail of 50mm dia.x16G pipe providing vertical support of 32x32 Sq. x 16G Pipe and Hori. Supports Pipe of 16mm x 16G 4 No. Row including grinding, cleaning and filling the welded spots with SS finish and including of labour transportation loading, unloading and all tex etc. complete.

RCC precast M.H. Frame & Cover Manufacture, supply & Delivery at store or at site of work precast RCC M.200 Frame & cover suitable to drainage M.H. and as per type design & Drawing including cost of reinforcement M.S. Angles or Flate, curring mold work etc. (Frame)

Description As Above Cover

Providing and Laying in position Controlled Concrete M-250 grade concrete for using cement content as per approved design mix, improve workability without impiring strength and durability as per direction of the engineer in charge. (min cement level as per latest ID: 456 shall be maintained) for 150mm thick trimix C.C Road with trimix vaccume dewatering system work with power trowling sheet form with M.S Channel, surface vibrator with providing road expansion joint having size 6mmx50mm by concrete cutter machine and filled with bitumen, finishing with floor hardener necessary all equipments, all labour charges complete.

Item Description

Road marking with hot applied thermoplastic paints with reflectorising glass beads on bitumin surface providing and laying a hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250gms per sqm area, thickness of 2.5mm is excluding of surface applied glass beds as per IRC:35-2015. The finished surface to be level, uniform and free from streaks and holes. zebra patta /bump patta lane/center line/ edge line/cut patta. The white color marking should provide liminance coefficinet on cemend road shalll be min 130 mcd/m2/lux and Asphalt road shall be min 100 mcd/m2/lux during the service life during the day time. The marking should meet the performance criteria for night time reflectivity, wet reflectivity and skid resistance as mentioned in the section-15 of IRC 35-2015. Warranty for the Retro reflectivity should be two years.

Supplying and fixing cat eye (Stimsonite) made out from Acrilo beautile sterine injuction high compressed molding with reflector made of MMC (prismatic type of size 12cm x 6cm x 2.5cm) provided with bituminous adhesive 100g. with each unit for fixing. (High Intensity grade)

Providing and fixing single layer waterproof gypusm board 12.5 mm thick of the make Newgood Group Co. Ltd. or equivalent & Newgood Group Co. Ltd. company sections using waterproof board of size 1220 mm x 1830 mm x 8.0 mm suspended by G.I suapender of size 25 mm x 3 mm with intermediate channel of size 18 mm x 40 mm x 0.80 mm at 1220 mm center to center ceiling section of size 40 mm x 35 mm x 0.55 mm at 457 mm center to center and perimetre chanel A of size 20 mm x 27 mm x 30 mm x 0.50 mm at edges & drops including paper tap sand sofit cleat, anchor fastener, scoch bolt connecting cleat joining compound top coat on ceiling including making necessary opening for light fitting, diffuser etc. complete as per detail drawing as directed.

Providing & Erecting Acrylic Letter - SS Still Letter (Silver / Gold / Rose Gold) 3D Box Letters on front side of gate Letter size of 12" Height & appropriate width with approved design. incl. cost of all Materials, Labour, erection charge, Trasportation, Loading, Unloading, all taxes, etc. complete work carried out as per directed by Engineer-in-charge.

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length , in below type of pipe erected with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed. CAT.III (a) with medium class Rigid PVC pipe and accessories erected flushed on wall/ceiling complete

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected with 6A Modular type switch and hum free EME step type electronic fan regulator mounted and accessories with earth continuity of following type erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed. CAT.lll (a) with medium class Rigid PVC pipe and accessories erected flushed on wall/ceiling complete

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected complete with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. CAT.III [I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb db board (a) with medium class Rigid PVC pipe and accessories erected flushed on wall/ceiling complete

Description As Above [II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db board. CAT.III (a) with medium class Rigid PVC pipe and accessories erected flushed on wall/ceiling complete

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of .ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires erected in below type of pipe with 6A Modular type switches and following type of accessories erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate modules erected on / in wall / ceiling as per pipe erected. with necessary batten/angle holder or ceiling rose or H.D.Connector as directed. CAT.III (a) with medium class Rigid PVC pipe and accessories erected flushed on wall/ceiling complete

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size (A) With medium class Rigid PVC pipe and accessories (a) 2 wire 1.5 sq. mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size (A) With medium class Rigid PVC pipe and accessories (b) 2 wire 2.5 sq. mm

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 50 K.A. and above at 415 V having normal current rating up to 630A. with variable thermal & magnetic release suitable to work on A.C.supply 50 cs. with all internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing. ICS 100 Percentage ICU only Cat-lIl

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 50 KA and above at 415 V having Normal current rating 400A. with variable Thermal & magnetic release suitable to work on A.C.supply 50 c/s. With all internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing. ICS 100 Percentage ICU only Cat-lIl

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 35 KA. and above at 415 V . having normal current rating 250A. with variable thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing. ICS 100 Percentage ICU only Cat-lIl

Providing and erecting Approved make Three pole moulded case circuit breaker having breaking capacity/strength ICU of 50 K.A. and above at 415V. having normal current rating 250A. with variable thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing. ICS 100 Percentage ICU only Cat-lIl

Providing and erecting Approved make Three pole moulded case circuit breaker having breaking capacity/strength ICU of 35 K.A. at 415 V. having normal current rating 125A.with Fixed thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing. ICS 100 Percentage ICU only Cat-lIl

Supplying and erecting triple pole & neutral 440V/ 500V panel mounting Aluminium Busbars with four equal Nos. of bus having current density not more than 0.8 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulating tape for phase sequence of following current carrying capacity, erected with necessary bus bar supports /insulators, main cable socket to each busbar,erected in existing cubical panel with necessary connections. (D) Suitable for 400 Amp. Capacity

Description As Above (E) Suitable for 630 Amp. capacity

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark. Cat.lll

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity (a) 6 to 32 Amp. Cat.lll

Description As Above (a) 40 Amp. Cat.lll

Description As Above (a) 63 Amp. Cat.lll

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity (a) 6 to 32 Amp. Cat.lll

providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase 240 V,50Hz. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed. (i) 25 Amps.DP Cat.lll

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for (B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (b) sheet steel double door (i) 4 way

Description As Above (i) 6 way

Description As Above (i) 8 way

Providing and erecting Sheet Steel powder coated Vertical MCB distribution board (VTPN) - flush / surface mounted double door (IP54) fitted with copper insulated busbar, isolated neutral bar, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3, suitable for 63/100 AMP TPN MCCB + RCCB as incomer and three phase outgoing as per following .(The DBs should be used of same company of MCB to be used) (A) 4 way outgoing

Providing and erecting metallic vitrified danger notice board as per language suggested by engineer incharge for MEDIUM VOLTAGE installation to be erected as per IS-2551.

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover. (A)(approved make OEM has to submit test certificate including value of earth resistance of installation duly stamped and signed by agency and officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate) & having back filling compound of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2 Percentage(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time Necessary test report must be submitted by Agency. [C] For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA)i.e. independent Earthing located in other than normal soil i.e. Soft Rock, Marshy Soil etc.. -Length of Pipe : 3 Mtrs. -Back filling Compound :2 nos Bags of 25 Kg.

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical panel board necessary IP-54 and above protection as per approval from engineer incharge made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for internal partitions with necessary accesories , supporting angles/ flats channel including cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per requirements & instruction of engineer-in-charge with erection of (The rates excludes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with following approved manufacturers with following size. (B) The standard companies switch gear shall be used and only manufacturers at CPRI approved factory (ii) with 550 mm. Depth

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. (B) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core)

Description As Above (F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core)

Description As Above (I) 3 1/2 core 240 Sq. mm( 120 Sq. mm 1/2 core)

Description As Above (J) 3 1/2 core 300 Sq.mm ( 150 Sq. mm 1/2 core)

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. (A) 4 core 4 Sq. mm

Description As Above (B) 4 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (A) 4 core 10 Sq. mm

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at required depth in existing trench for laying of cable. below ground / road surface for enclosing cable. (D)120 mm outer dia.

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (A) 1.5/ 2.5/4/6 Sq.mm

Description As Above (B) 10 Sq.mm

Description As Above (C) 16/25 Sq.mm.

Description As Above (D) 35/50 Sq.mm.

Description As Above (E) 70 Sq.mm.

Description As Above (G) 120 Sq.mm.

Item Description

Description As Above (H) 150 Sq.mm.

Description As Above (K) 300 Sq.mm.

Solder less crimping type Copper lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool and connected to switchgear terminals with brass cadmium plated nut bolts in an approved manner. (B) 10 Sq.mm

Providing and erecting Approved make Ceiling fan with double ball bearing ISI mark with condenser A.C. 23OV.50 c/s.1200 mm. sweep complete, canopy erected on existing hook or clamp with earthing. [Make shall be approved by Engineer in charge]

Supplying and erecting approved make low noise decorative exhaust fan having square frame ABS body with inbuilt lowers and square frame. 250mm with 1350 RPM Cat.II

Providing and erecting Inverter based approved make split airconditioning unit consisting of condensing unit with variable speed fan motor, inverter type hermetically sealed rotary compressor with accessories etc. duly connected separately erected evaporating unit and blower motor with its accessories by means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( cost includes Eco Friendly green gas charging and 15A plug top and Remote Control and MS Stand) with necessary core cutting. (B) for 1.5 ton capacity

Providing and erecting Inverter based approved make Cassette type split airconditioning unit consisting of condensing unit with fan motor, hermetically sealed scroll/rotary compressor with accessories etc. duly connected separately erected evaporating unit and blower motor with its accessories by Eco friendly Green gas charging and Internal copper wiring and Remote control ( 3 star and above of current year) with necessary core cutting. (D) for 4 ton capacity 1/3Phase

Description As Above (B) LED Panel Light with provision for Plane front frame with translucent cover fixed to housing complete.IP20 (vi) 36 watts, 24" x 24", Surge 2KV Cat.lll

Description As Above (I) Adjustable spot light with COB led having aluminium reflector of following wattage (iv) 30 Watts Cat.lll

Providing and fixing approved make Perforated C type cable tray. Made from sheet steel. The cable tray should be single or double bended as per required and as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with max 17.5 Percentage perforation with coupler plate / Fish plate and GI hardware like nut bolt and washers etc. erection with necessary support( included) as per Specification and as per instruction of engineer in charge. (2) 100 X 50 X 1.6 mm Thick

Providing and fixing approved make 'T' Junction for Perforated C type cable tray. Made from sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with max 17.5 Percentage perforation with coupler plate / Fish plate and GI hardware like nut bolt and washers etc. erected on existing support as per Specification and as per instruction of engineer in charge of following size (2) 100 X 50 X 1.6 mm Thick

Providing and fixing approved make '90° Elbow' for Perforated C type cable tray. Made from sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut bolt and washers etc. erected on existing support as per Specification and as per instruction of engineer in charge. (2)100 X 50 X 1.6 mm Thick 90° Elbow

Providing and erecting approved make ductable split Air Conditioning unit each consist of remote located condensing unit and an evaporating unit complete with interconnecting insulated refrigerant piping up to 10 RMT. rigid PVC, drain piping of 10 kg / cm2 dully insulated with nitrile rubber insulation of 10 RMT with ECO Friendly Green gas. The condensing unit is complete with hermetically sealed scroll compressor and condenser unit which effectively achieves heat rejection by utilizing air of fan and coil type condenser. The evaporating unit will be complete with DX evaporator centrifugal blower, blower motor along with microprocessor biased remote controller with memory backup etc. (D) For 16.5 Ton

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class0 tubular insulation/with Class0 closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc with necessary refrigerant joint as required : (D) 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

Description As Above (H) 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber insulation. 25 mm Dia.

Description As Above 32 mm Dia.

Description As Above 40 mm Dia.

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. (A) Thickness 0.63 mm sheet (22 Gauge)

Description As Above (B) Thickness 0.80 mm sheet (20 Gauge)

Supplying and fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers complete as per specifications and size and shape as per site requirement and approved design.

Supplying and fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as per specifications and size and shape as per site requirement and approved design.

Supplying, fixing testing commissioning of supply air diffuser of powder coated aluminium with aluminium volume control dampers with anti smudge ring and removable core and size and shape as per site requirement and approved design.

Supplying, fixing testing commissioning of Return air diffuser of powder coated aluminium without volume control dampers with anti smudge ring and removable core and size and shape as per site requirement and approved design.

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. (A) 19mm

Description As Above (B) 25mm

Supplying and fixing 50mm thick TF quality expanded polystyrene for underdeck insulation on slab/wall /shaft exposed to sun/atmosphere as per specifications.

Providing and erecting XLPE(IS:7098)(I)88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (J) 3 1/2 core 300 Sq.mm (150 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)88 ISI armoured cable multistrand / Solid Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (C) 4 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (A) 4 core 10 Sq. mm

Providing and erecting weather proof, dust and vermin proof, floor mounted front operated outdoor type double door cubical panel board necessary IP54 and above protection as per approval from engineer incharge made from 14 SWG thick CRC M.S. sheet for outer body and doors, 16 SWG thick CRC M.S.sheet for internal partitions with necessary accesories, supporting angles/ flats channel including cutting, bending, drilling, welding, riveting with internal partitions and cable alley as per requirements and instruction of engineerincharge with erection of supplied switch gears, BUSBARS, suitable size of inter connecting PVC copper wire / copperaluminium strips, rubber grommets, rib, bakelite control fuses/MCB for measuring instruments, earth bus and earth bolts, foundation flange boltsbase Plates, sufficient nos. of hinged doors, handles with locking arrangement and rubber gasket,heavy duty end terminal connection,danger notice board,necessary ventilation,earthing strip complete. The Panel shall be painted with epoxy powder coating. (B) The standard companies switch gear shall be used and only manufacturers at CPRI approved factory (ii) with 550 mm. Depth

PreInsulated Duct and Accessories Supply installation balancing and commissioning of pre insulated factory fabricated PIR (polyisocyanurate foam panel or board) ducts made up of CNC machine cut for internal use. The thickness of board shall be 20mm density of foam shall be 45 kg/m³ thermal conductivity 0.020W/m.K. The aluminium foil shall be 80µ thick and provided on both sides and the foil shall be embossed. All accessories adhesive sealant and tape used in duct fabrication should be same as panel manufacturer erected with necessary supports.

Supply of Approved make Iron Clad or metal clad four pole change over switch 415V. confirming to IS of following capacity (B) 400 A Cat III

Providing and erecting busbar chamber confirming to IS375 fabricated from 16 G.M.S. sheet, dust and vermin proof having hinged door with rubber gasket and necessary busbar supports with Aluminium busbar having current density not more than 0.8 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulation tape for phase sequence, three phase and neutral each Suitable for following current capacity with necessary painting mounted on wall or pedestal frame of required size with necessary connections.(D) Suitable for 400 Amp. capacity

Providing and erecting metallic vitrified danger notice board as per language suggested by engineer incharge for MEDIUM VOLTAGE installation to be erected as per IS2551.

Providing and erecting required size Aluminium strip for earthing of H.T. , OCB / ACB / Transformer, LT panel board, Motors etc. using copper clamp.

providing and erecting Approved make Three Phase and Neutral LT Heavy Duty Switch Disconnector Fuse Unit Cubical type for panel mounting complete with operating mechanism suitable to operate on 415V A.C., 23A duty With HRC fuses of suitable load confirming to IS. 13947 (Part I and III). of following capacities. (g) 400 Amp Cat.III

Supplying and erecting approved make panel mounting type Digital Voltmeter having 3 digits LED display, 0 to 750 AC Volts range erected on existing panel board with all connection, wiring etc .with manufacturers calibration certificate. Cat.III

Supplying and erecting approved make Analog type moving iron Ammeter direct reading type 030A AC current, 500 V square /. Round dial, flush or projection type complete erected with connection and wiring.

Supplying and erecting approved make Analog type moving iron C.T operated Ammeter A C Current suitable slide in scale 0 400 Amp. with 3 Nos. of Current Transformer erected on panel board with connections.

Supplying and erecting approved make suitable panel indicator LED type lamp, lens cover, complete erected with necessary connections.

Item Description

Providing and Fixing of Mat finish Teak wood Auditorium Stage Wooden Flooring as per reuired size and 15 to 22mm thick with toungue groove locking system based on plywood including adhesive materials and all labour, transportation and fitting charge make : Action Tessa/ Vista/Green/ Hogan Plywood

Providing and Fixing Floor Carpet Synthetic Pills Of 6 mm Thick Using With SR Adhesive 707 Pidilite ,Erecting ,and Furnishing of american pipe figured belt of size 50mm/60mm x 10mm thick with Skirting at Periffery Of Wall and it should polished with matt melamine etc As Per Directed By Architect/Enegineer

P and F Acoustical Doors along with 150 x 150 mm teak wood frame, doors made from 50mm Teak wood frame 600 x600 c to c filled with synthetic wool 50mm thick and 5mm Tec sound from both sides, 12mm waterproof ply and veneer from both sides , including 100mm heavy duty SS hinges 4 no each leaf, with Doorcloser (Dorma / Geze or eq.) including cost of required CutOuts, decorative mouldings / finishingitems / melamine polish and Scaffolding as per Architectural and Acoustical Design and Instructions and Complete in all aspects (10 doors) system complete as per approve by consultant Approved makes: Illuminar, GCS Stage Craft, Neo Stage Craft

Providing and fixing of 15mm thick Acoustic Rockwool ceilling sheet size of 595x595mmx15mm thick with M.S. "T" Section frame 24mm size and Suspended from tie of roof truss using Alum. Screws and strictly as per acoustic curve, with finishing and white and black colour, surface finish of anti fungal antialgea paint, lightweight and High strength long lasting fireproof materials all labour, loading, unloading, transportation etc. complete Approved makes Gyptech

P and F Side Walls for Hall and Stage: 12 to 15mm thick Perforated Gypsum sheet frame of 0.5mm G.I. channel grid frame including fixtures and fasteners with 50mm 32kg/m3 glass wool cushion with nonwoven fabric 250gsm with adhesive on all surface. Approved makes: Action Tessa/ Vista/Green/ Hogan Plywood

Providing, laying, testing and commissioning of C class Heavy duty G.I. pipe comforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolt, gaskets etc. and fixing the pipe on the wall/ceilling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as reuiqred 100mm Dia.

80mm Dia.

50mm Dia.

25mm Dia.

(A) Supplying, installation, testing and commissioning of electric drivin MAIN FIRE PUMP suitable for automatic operation and consisting of following complete in all respects as reuiqred (B) Suitable HP squiirel cage induction motor TEFC synchronous speed 1500 RPM suitable for operation on 415 volts 3 phase 50 Hz AC supply with IP 55 protection fo enclosure horizontal foot mounted type with class F insulation confirming to IS325 (C) Horizontal type multistage centrifugal, split casing pump of cast iron body and bronze impeller with stainless steel shaft mechanical seal confirming to IS1520 (D) M.S. fabricated common base plate, coupling, coupling guard foundation bolts etc. as required (E) Suitable cement concrete foundation duly plastered with anti vibration pads (2280 lpm at 88 Mt. Head Required HP)

(A) Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following complete in all respects as required (JOCKEY PUMP) (B) horizontal type multistage centrifugal pump of cast iron body and bronze impeller with stainless steel shaft mechianical seal conforming to IS 1520 (C) suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure horizontal foor mounted type with class F insulation conforming to IS 325 (D) M.S. Fabrication common base plate coupling coupling guard foundation bolts etc. as required (E) suitable cement concrete foundation duly plastered and with anti vibration pads 180 lpm at. 70 Mt. Head Required HP

(A) Supplying, installation, testing and commissioning of Diesel engine driven main fire pump suitable for automatic operator and consisting of following, complete in all respects, as required : (Diesel Driven Pump) (B) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaftm mechanical seal confirming to IS 1520 (C ) Suitable HP, 1500 RPM water cooled with radiator diesel engine confirming to relevant IS Standard complete with auto starting mechanism, 12/24 volt electric starting equipment, diesel tank exhaust pipe extended up to 10M outside pump house duly insulated with 50mm thick glass wool with 1.0mm thick aluminium sheet cladding, residential silencer, intruments and prorection as per standard specification, stop solenoid for auto stop in the event of fult with audio indication painted with post office red color etc. as required (D) M.S. Fabricated common base plat coupling coupling guard foundation bolts etc. as required (E) Suitable cement concrete foundation duly plastered and with anti vibration pads. 2280 lpm 70 Mt. Head Required HP

Supplying and fixing single headed internal Hydrant valve with instantaneous Gunmetal/stainless steel coupling of 63mm dia. With cast iron wheel ISI marked conforming to IS 5290 (TypeA) with blank Gunmetal/Stainless Steel cap and chain as required (Single headed stainless steel

Supplying fixing testing and commissioning of Butterfly valve of PN 1.6 rating with bronze/gumetal seat duly ISI marked complete with nuts bolts washers gaskets confirming to IS 13095 of following sizes as required. 100mm Butterfly Valve

80mm Butterfly Valve

Supplying fixing first aid Hose Reel with MS construction spray painted in cost office red. Conforming to IS 884 complete with the following as required 20mm nominal internal dia. Water hose thermoplastic (Textile reinfored) type2 as per IS 12585 20mm nominal internal dia gun metal globe valve and nozzle. Drum and bracket for fixing the equipment on wall. Connection from riser with 25mm dia. stop bun metal valve and M.S. pipe and socket 30.0 Mt.

Supplying fixing 63mm dia. Gun metal short branch pipe with 20mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required Gun Metal

Supplying fixing 63mm dia. 15 Mt. long RRL hose pipe with 63mm dia. Male and female coupling duly bound with GI wire, rivets etc. conforming to IS 636 (typeA) as required Gun Metal

Providing and fixing pressure Switch in M.S. Pipe line including connection etc. as required

Supplying and fixing of fire bridges connection of cast iron body with gun metel male instantaneous inlet couplings complete with cap and chain as reuiqred for suitable dia. MS pipe connection conforming to IS 904 as required. 2 Way100mm Dia. M.S. Pipe

Providing and fixing of Dial type Pressure Gauge having 100 mm dial and range of 014 Kg/cm2 with isolation ball valve.

Providing, installation testing and commissioning of nonrerutn valve of following sizes confirming to IS 5312 complete with rubber gasket GI bolts nuts washers etc. as required 100mm Dia.

Supply, installation, testing and commissioning of lockable cabinet made out of MS sheet having central opening and 4 mm thick glazed glass doors (one nos.) suitably marked on the outside with the letters "FIRE HOSE" with one coat of primer and coat of synthetic paint of approved shade. The cabinet shall be suitable to accommodate 2 nos. 15 mtr long Hose pipe and 1 No branch pipe nozzle. It shall be mounted on raised Brick platform complete as required.

SITC of Aid zone Fire Alarm Control Panel The Panel shall be compliant with EN542, EN544 and approved by LPCB. The Fire Alarm Control Panel shall have inbuilt one loop. The Panel must have large graphic display. The Panel must also have the capability to take Wired and Wireless Devices on same loop. Each loop shall have a sounders/Base Sounder Beacons. The Panel shall have power supply along with automatic

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size (c) 3 wire 1.5 sq. mm

(a) 2 wire 1.5 sq. mm

Providing and supplying C.I. Air Valves of approved make and quality of following class and dimater including all taxes, insurance transportation freight charge octroi inspaction charge, loading, unloading conveyance to department stores stacking etc. complete Air Vales Single

Supply and installation and commisioning of C.I body below sized foot valve including all accessories 100mm Dia.

Supplying, installation, testing and commissioning of Smoke Detector with builtin LED and mounting base complete with all connections as required.

Supplying, installation, testing and commissioning Fire Alarm souder with facility to make announcement, mounted in M.S. box (16 SWG) with hinges cover plate and suitable for operation with amplifier i/c line matching transformaer etc. complete as required

Providing and fixing of ABC 6.0 Kg. Extinguisher, Steel body (as per latest IS 7285), Low Pressure Extinguisher (Service Pressure ≤19 bar), Steel body (as per latest IS 7285) Welded low carbon steel cylinders (as per Clause 9.2.5 of IS 15683), Weight of Filled Portable FireExtinguisher 9 kilogram, Features of Fire Extinguisher Carrying Handle (Mandatory If Extinguisher having mass ≥ 1.5 Kg or Cylinder diameter, Rechargeable, Operating Temperature (°C) 30°C to +60°C

Providing and fixing of CO2 4.50 Kg. Extinguisher, Steel body (as per latest IS 7285), Low Pressure Extinguisher (Service Pressure ≤19 bar), Steel body (as per latest IS 7285) Welded low carbon steel cylinders (as per Clause 9.2.5 of IS 15683), Weight of Filled Portable FireExtinguisher 9 kilogram, Features of Fire Extinguisher Carrying Handle (Mandatory If Extinguisher having mass ≥ 1.5 Kg or Cylinder diameter, Rechargeable, Operating Temperature (°C) 30°C to +60°C

Providing, fixing, testing and commissioning of 15mm dia. Quartzoid bulb type sprinklers of rating 68 degree centrigrade with reuired accessories

Providing, fixing, testing MCP as Required capacity

Providing and fixing of auto tip up Auditorum Chair Auditorium Chairs / Seating Auditorium Seating is a style of commonly used event layout, comprised of chairs aligned in consecutive straight rows, generally facing a single direction. It is sometimes called stadium seating. Type of Chair Mechanism Auto Seat Tip Up with Sliding Seat with Push Back Chair Under Structure MS under structure with integrated auto tipup mechanism with suitable welded base plate Chair legs Rectangular MS ERW Tube of size 60 X 40 X 2mm with welded 5 mm thick base suitable base plate from grouting the chair legs and understructure. Chair Under Structure Legs Finish Antirust treatment and powder coated Type of Seat Fabric upholstered seat made of high density PU foam backed with 12mm ±1mm thick moulded plywood with plastic moulded under seat cover high Density of PU Foam for Seat (Kg/m^3) 50, Thickness of PU Foam for Seat (in mm) 100 millimeter Width of the Seat in mm >400400600400<500 Actual Backrest Width in mm 430 Backrest Upholstery Fabric Armrest Independent armrest in aisle side and Foldable Writing Pad on RHS Side in middle seats Type of Armrest PU Moulded and Armrest with Cup Holder Yes Side Panel / Aisle Panel Made from 1.2~1.6 mm CRAC sheet, clad with upholstery fabric with suitable foam layer and Warranty of Chair 3 year

Supply, Installation, Testing and Commissioning of PASSIVE HYBRID CURVATURE ARRAY SPEAKER with 15″ Coxial passive, System Type : 2Way, Voice Coil Size : 4", System Peak SPL : 141 DB**, Nominal Coverage : 100° x 20°, Frequency Response (+/3 dB) : 42 Hz – 20 kHz, Frequency Range (10 dB) : 25 Hz – 25 kHz, Sensitivity (2.83 v / 1 m) : 102 dB, Crossover Frequency : 1.2 KHz, Power (RMS / Programme / Peak): 500W / 1000W / 2000W, Nominal Impedance: 8Ω, Inputs 2 x Speakon

Supply, Installation, Testing and Commissioning of PASSIVE DUAL 18" SUBWOOFER with Dual 2 x 18″ LF driver swith 4.0″ voice coils, Max SPL (@ 1 MTR.) : 148 dB , Frequency Response (+/3 dB) : 30 800 Hz, Frequency Range (10 dB) : 25800 Hz, Sensitivity (2.83 v / 1 m) : 109 dB, Power (RMS / Programme / Peak): 2000W / 4000W / 8000W, Impedance : 4Ω, Inputs : 3 x Speakon

Supply, Installation, Testing and Commissioning of PASSIVE ARRAY SUBWOOFER with 21″ Coxial LF, Voice Coil Size : 4" Quattro, System Peak SPL : 147 DB**, Frequency Response (+/3 dB) : 25 Hz – 100 Hz, Frequency Range (10 dB) : 18 Hz – 125 Hz, Sensitivity (2.83 v / 1 m) : 103 dB, Crossover Frequency : 100 KHz, Power (RMS / Programme / Peak): 1600W / 3200W / 6400W, Nominal Impedance : 4Ω, Inputs : 2 x Speakon

Supply, Installation, Testing and Commissioning of PASSIVE SPEAKER FOR SURROUND , Configuration: 2Way, LF Drivers : 10" , HF Coil : 1.75" Titanium , Voice Coil Size : 2.5", Frequency Response (+/3 dB) : 6520 kHz, Frequency Range (10 dB) : 6020 kHz, Sensitivity (2.83 v / 1 m) : 97 dB, Crossover Frequency : 2.8 KHz, Power : RMS: 300W, Program: 600W, Peak: 1200W, Max SPL : 128 db, Nominal Coverage : 90⁰ x 60⁰, Impedance: 8Ω, Input: 2 x Speakon

Supply, Installation, Testing and Commissioning of PASSIVE SPEAKER FOR STAGE MONITOR with 15″ , System Type : 2Way, Voice Coil Size : 3", Syatem Peak SPL : 131 DB**, Frequency Response (+/3 dB) : 5520 kHz, Frequency Range (10 dB) : 5020 kHz, Sensitivity (2.83 v / 1 m) : 98 dB, Crossover Frequency : 1.8 KHz, Power (RMS / Programme / Peak): 500W / 1000W / 2000W, Nominal Impedance : 8Ω, Inputs 2 x Speakon

Supply, Installation, Testing and Commissioning of POWER AMPLIFIER 4CHANNEL For Main Line Array Speaker And Surround Speaker With Stereo Power Output (per channel): 1000W X 8Ω, 1700W X 4Ω, 2890W X 2Ω, Frequency Response (+/3 dB @ 8 OHMS) : 20 Hz – 30 KHz, Digital, Voltage Gain : 38db, Topology : Class D, Signal Input : XLRF, Jacks, Signal Output : Speakon,Jacks, Multi Channel, Lightweight, Protection : Thermal protect, Overcurrent protect, Output DC protect, Output short protect, Power on/off mute

Supply, Installation, Testing and Commissioning of POWER AMPLIFIER 2CHANNEL For Subwoofer With Stereo Power Output (per channel): 2000W X 8Ω, 3400W X 4Ω, 4760W X 2Ω, Frequency Response (+/3 dB @ 8 OHMS) : 20 Hz – 30 KHz, Digital, Voltage Gain : 38db, Topology : Class D, Signal Input : XLRF, Jacks, Signal Output : Speakon,Jacks, Multi Channel, Lightweight, Protection : Thermal protect, Overcurrent protect, Output DC protect, Output short protect, Power on/off mute

Supply, Installation, Testing and Commissioning of DIGITAL AUDIO MIXING C0NSOLE with Live performance and studio recording digital console with up to 40 simultaneous input channels. 32 awardwinning Midas Daylight viewable 7” full colour TFT displaymicrophone preamplifiers.192 kHz ADC and DAC converters for outstanding audio performance. 8 DCA and 6 mute groups, 8 stereo signal processing effects engines, 25 Midas PRO motorised 100 mm faders, screen, 32 x 32 channel USB 2.0 audio interface, Optional wireless remote control with Midas Apps for iPhone* iPad*, Autoranging universal switchmode power supply.

Supply, Installation, Testing and Commissioning of DI 32 STAGE BOX with 16 electronically balanced low impedance line level outputs ULTRANET personal monitoring system connectivity for inear applications, 32 awardwinning Midas PRO microphone preamplifiers with switchable 48 V phantom power. Dual AES50 SuperMAC ports for cascading additional DL16 stageboxes—no merger or router required. Automatic AES50 stagesplit mode when connected between Midas M32 Series FOH and monitor console Dual ADAT outputs providing 16channel digital output on two optical TOSLINK connectors. 2 AES3 ports (AES/EBU), for directly connecting PA system controllers with digital inputs. Remote operation via shielded CAT5e cable up to 330 ft / 100 m length. Mute All function for quietly patching any inputs on stage. Rugged 3U rackmount chassis for durability in portable applications Autoranging universal switchmode power supply.

Item Description

Supply, Installation, Testing and Commissioning of DYNAMIC CARDIOID VOCAL MICROPHONE with Cuts through high onstage levels, Clear reproduction with a high presence, Consistent sound quality, Handles high sound pressure levels, Excellent feedback rejection, Connector: XLR3, Frequency response: 40 16000 Hz, Sensitivity in free field, no load: 2.7 mV/Pa, Nominal impedance: 350 Ω, Min terminating impedance: 1000 Ω

Supply, Installation, Testing and Commissioning of GOOSENECK MICROPHONE FOR PODIUM with intregrated 3pin XLR with configurable pushbutton and XLRequipped bases, Excellent feedback rejection, Connector: XLR3,

Supply, Installation, Testing and Commissioning of WIRELESS HANDHELD MICROPHONE System with Frequency response: 50 to 16,000 Hz (–3 dB), THD, total harmonic distortion: ≤ 0.9Percentage, Pickup pattern: cardioid , Signaltonoise ratio :≥ 103 dBA , RF output power: 10 mW , Switching bandwidth: up to 24 MHz, Modulation: wideband FM, Output voltage: 1/4“ (6.3 mm) jack socket (unbalanced): +6 dBu, XLR socket (balanced): +12 dBu, Frequency range A: 548572 MHz, C: 766790 MHz, K: 925937.5 MHz, Sensitivity: < 3 μV at 52 dB(A)rms S/N, Synchronization: 2.4 GHz, Low Power OQPSK, Input sensitivity: 1.8 mV / P. Line / Mic level: 20 dB, switchable

Supply, Installation, Testing and Commissioning of WIRELESS LAVALIER MICROPHONE System with Frequency response: 50 to 16,000 Hz (–3 dB), THD, total harmonic distortion: ≤ 0.9Percentage, Pickup pattern: omnidirectional , Signaltonoise ratio :≥ 103 dBA , RF output power 10 mW , Switching bandwidth: up to 24 MHz, Modulation : wideband FM, Output voltage: 1/4“ (6.3 mm) jack socket (unbalanced): +6 dBu, XLR socket (balanced): +12 dBu, Frequency 8 frequency banks, Frequency range A: 548572 MHz,: C: 766790 MHz, K: 925937.5 MHz, Synchronization 2.4 GHz, Low Power OQPSK, Adjustment Range Transmitter 0 to 30 dB, adjustable in 10 dB steps, Audio adjustment range 40 dB,adjustable in 5dB steps , Line / Mic level 20 dB, switchable

Supply, Installation, Testing and Commissioning of STEREO GRAPHIC EQUALIZER with FBQ Feedback detection system, Dedicated Limiters with gain reduction meters for each channel peotect your sound system from overload and distrotion, pink noise generator provides test signels to adopt your sound system to any room acoustics, Mono subwoofer, output decicated level control and adjustable ceossover frequency, servo balanced inputs and outputs with 1/4" TRS and XLR connectors, UltraLow noise audio operational amplifiers for highest signel integrity, Shielded torodial power transformer for ultralow noise perfomance.

Supply, Installation, Testing and Commissioning of 13,000 LUMENS 3LCD LASER PROJECTOR with 4K Enhancement, accepts 4K content and delivers up to 4.6 million pixels onscreen for an incredibly crisp and vibrant image, high native contrast ratio produces deep blacks; frame interpolation delivers re+C58alistic moving images; HDR support4 and scene adaptive gamma correction for truetolife images, Interface: 3G SDI in/out; HDMI x 1 (HDCP 2.3); HDBaseT x 1; DVID x 1; VGA x 1; Variable audio out: Mini Stereo x 1; USB Type B x 1; USB Type A x 2 (5 V, 2.0 A); USB Type A for Wireless LAN (optional); Serial: RS 232C x 1 (9pin); Remote Mini Stereo; Network: RJ45, Video Input: Input Video Signal (HDMI®, DVID and HDBaseT™ ports) 3840 x 2160/ 4096 x 2160, Contrast Ratio: 2,500,000:1.

Supply, Installation, Testing and Commissioning of HEAVY DUTY PROJECTOR CEILING MOUNT KIT of weight carrying capacity of minimum 25 kgs. with variable projector connection arms, fitted on M.S. fabrication at desired height and angle.

Supply, Installation, Testing and Commissioning of HDMI FIBER CABLE High Speed with Ethernet, for Projector to Operating Room, HDMI 2.0, Bandwidth 18Gbps, Resolution : 4K (3840X2160)@60Hz, Shielding : Aluminium Foil, Cable Gauge: 30AWG*2C+28AWB*4C+24AWG*1C (50 Mtrs.)

Supply, Installation, Testing and Commissioning of LARGE VENUE TABTENSION MOTORIZED SCREEN, High Speed, Mute Tubular Motor, and equipped with RS45, IR/RF control, 12V trigger port and high quality controller, Screen size (Wide x Height): 16 ft. x 9 ft. Screen size (Diagonal): 220, Aspect Ratio : 16:10.

Supply, Installation, Testing and Commissioning of 4K HDMI OVER HDBase TX RX with Resolution: 4096×2160 @60Hz, Colorspace: YCbCr, RGB, Chroma Subsampling: 4:4:4, Color DepthL 8bit, 10bit, 12bit, Sample Rate: 96kHz, 176.4kHz, 192kHz, Bit Rate: up to 24bit, Bandwidth 10.2 Gbps, HDCP 2.2 compliant, 4K HDR10 @ 24 Hz, Connectivity: Firmware: MiniB USB, HDBaseT: RJ45, HDMI Type A, Supply Input: AC100~240V 50/60Hz, Output: DC 5V/1.2A

Supply, Installation, Testing and Commissioning of HDMI CABLE High speed with Ethernet, Data Transfer Speed 10.2Gbps, Supported 3D and 4K Resolution up to 4K X 2K @ 30Hz, Cable Gauge 24 AWG ( 2.0 m)

Supply, Installation, Testing and Commissioning of METAL STAGE BOX with microphone connector, Per Stage box 4XLR body mount Connector.

Supply, Installation, Testing and Commissioning of FLY BAR WITH CHAIN PULLY for Line Array Speaker Mounting / Hanging arrangement system.

Supply, Installation, Testing and Commissioning of MIKE STAND with height and angle adjustable, Floor and Table Stand.

Supply, Installation, Testing and Commissioning of SPEAKER CABLE with 2.5 Sq. mm. 2 Core ATC, twin twisted, Tinned Copper Speaker Cable with laynig.

Supply, Installation, Testing and Commissioning of MICROPHONE DIGITAL SIGNAL CABLE 25/42 SWG, Shielded, ATC Lapp with laynig.

Supply, Installation, Testing and Commissioning of CAT6 STP FOIL SHIELDED CABLE.

Supply, Installation, Testing and Commissioning of 3Phase Servo 10 KV STABILIZER.

Supply, Installation, Testing and Commissioning of WALL MOUNT CLAMP for surround Speaker.

Supply, Installation, Testing and Commissioning of EQUIPMENT AV RACK 42U with Rack with 600mm x 650mm, Glass Door, Castor Wheels Set, Standard Rack mount Power Distribution Unit with 6 Skt. x 5 Amp., Cantilever Tray, Horizontal Cable Manager, Roof Mount Cooling Fan, Mounting Hardware and all Accessories.

Supply, Installation, Testing and Commissioning of VARIOUS AV CONNECTORS, Patch Codes and Required Accessories for equipment placement.

Supply, Installation, Testing and Commissioning of Calibration and Traning of above AudioVisual System.

Supply, Installation, Testing and Commissioning of PROFILE HELOGEN SPOT LIGHTS 1000 Watt with Lamp : Halogen 1000 watt, Reflector : Ellipsoidal Anodized Aluminium Reflector, Lens : 2Nos. 150 mm P.C. Lens, Housing : C.R.C. Metal Black, Focussing by Manipulating Tubing

Supply, Installation, Testing and Commissioning of LED PAR LIGHTS Aura 24 LED x 10w, Lamp : 24 Pcs. X 10W High Brightness RGB Led, Beam Angle : 25°, Life Time : 50000 Hrs., Dimmer : 0100Percentage Linear Light Dimmering, Strobe : 020 F/S, Random or Pulse, Speed Adjustable, Control Mode : DMX 512, Auto, Sound, MasterSlave, DMX Channels : 4/8 Channels, Display : LCD Display, Input Voltage : AC 100240V 5060HZ

Supply, Installation, Testing and Commissioning of SEALED PAR64, 1000w, 240volt, Sealed beam available in three types i.e. Sopt , Medium flood and wide flood, Color temperature : 3200k, Housing CRC sheet metal with black/silver finish with adequate ventilation and 0.25 mtr, 2 core wire

Supply, Installation, Testing and Commissioning of MOVING HEAD LIGHTS thro 295W Beam 10R with Lamp : Osram, Beam Angle : 2°50°, Life Time : 2000 Hrs., Colour wheel : 14 Colours + White, 6 Color Wheel (Rainbow), Gobo Wheel : 11 Gobos + 6 Glass Gobo, Effect Wheel : 24 Facet Prism, Dimmer : 0100Percentage Linear Light Dimmering, Strobe : 014 F/S, Random or Pulse, Speed Adjustable, Pan and Tilt : Pan 540° (16Bit) Tilt 270° (16Bit), Control Mode : DMX 512, Auto, Sound, MasterSlave, Dmx Channels : 16 Channels, Display : LCD Display

Supply, Installation, Testing and Commissioning of LED LASER LIGHTS 2 Diod, Red 0.2 mm and green 0.5 mm with heatsink.

Supply, Installation, Testing and Commissioning of LED BLINDER BLAZE 2100 with Lamp : 2 Pcs. X 100W COB Led, no UV Radiation, Beam Angle : 60°, CCT : 3000K/4000K/6500K, Life Time : 50000 Hrs., Dimmer : 0100Percentage Linear Light Dimmering, Strobe : 030 F/S, Random or Pulse, Speed Adjustable, Control Mode : DMX 512, Auto, Sound, MasterSlave, DMX Channels : 6 Channels, Display : LCD Display, Input Voltage: AC 100240V 5060HZ

Supply, Installation, Testing and Commissioning of LED BLINDER BLAZE 4100 with Lamp : 4 Pcs. X 100W COB Led, no UV Radiation, Beam Angle : 60°, CCT : 3000K/4000K/6500K, Life Time : 50000 Hrs., Dimmer : 0100Percentage Linear Light Dimmering, Strobe : 030 F/S, Random or Pulse, Speed Adjustable, Control Mode : DMX 512, Auto, Sound, MasterSlave, DMX Channels : 6 Channels, Display : LCD Display, Input Voltage: AC 100240V 5060HZ

Supply, Installation, Testing and Commissioning of STROBE LIGHTS 1500 watt DMX Operating, xeon Lamp.

Supply, Installation, Testing and Commissioning of CYCLORAMA LIGHTS for lights effects on Cyclorama Screen.

Supply, Installation, Testing and Commissioning of FOG MACHINE 2000 Power : 2000w, Control Method : Wireless Remote and DMX 512, Warmup Time : 5 Minuts, Tank Capacity : 2.5 L, Output : 20000 Cu.Ft./Mints, Spray Distance : 78 Mtrs., Input Voltage : AC 100240V 5060HZ , smoke fluid and the smoke both are safe. .

Supply, Installation, Testing and Commissioning of SPLITTER 8 CHANNEL with DMX 512 Signal and Martin Signal, Improve the loss of Signal During LongRange Transmision, 1 Input and 1 thro Output (Isolated), 8 Distribute Output, DMX Input Connector : XLRD3M/XLRD5M, DMX Thru Output Connector : XLRD3F X4/XLRD5F, DMX Distribute Output Connector : XLRD3F/XLRD5F

Supply, Installation, Testing and Commissioning of MOTORISED STAGE LIGHTING BAR on Stage Fixed with approx. size of MS Pipe 6MM X 50MM Dia and Length 45 Ft. to be Fixed from the existing main Structure / Grid / Beams / Ceiling, MS Pipe Supported by AI Brackets duly painted Black.

Supply, Installation, Testing and Commissioning of LIGHTING CONTROLLER Pearl Board for Lighting Arrangement Mixer.

Supply, Installation, Testing and Commissioning of DMX 512 Lighting Arrangement Mixer.

Supply, Installation, Testing and Commissioning of POWER CABLE WITH 2.5 Sq. Mm. 3 Core for power supply.

Supply, Installation, Testing and Commissioning of PRODIGITAL SIGNAL CABLES 25/42 SWG for DMX Operating.

Supply, Installation, Testing and Commissioning of CLAMPS for Lights with die cast Alluminium / Iron / MS flat, Clamp are for safe hanging the Light Fitting on Lighting Bar size as per site required.

Supply, Installation, Testing and Commissioning of 3PHASE SERVO 10 KV STABILIZER.

Supply, Installation, Testing and Commissioning of EQUIPMENT RACK 27U with Rack with 600mm x 650mm, Glass Door, Castor Wheels Set, Standard Rack mount Power Distribution Unit with 6 Skt. x 5 Amp., Cantilever Tray, Horizontal Cable Manager, Roof Mount Cooling Fan, Mounting Hardware and all Accessories.

Supply, Installation, Testing and Commissioning VARIOUS CONNECTORS, Patch Cords and Accessories for Stage lighting arrangement.

Supply, Installation, Testing and Commissioning of Stage Lighting System Programing, Setting and Traning.

Supplying and erecting in earthpit of minimum bore dia. 225mm size approved make Safe Earthing Electrode consisting PipeinPipe Technology as per IS 30431987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 80 mm having 80200 Micron galvanising, Inner pipe dia of 40 mm having 200250 Micron galvanising, connection terminal dia of 14 mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover.(approved make OEM has to submit test certificate including value of earth resistane of installation. [C] For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant and Sensitive Computer System(like Automation, SCADA)i.e. independent Earthing located in other than normal soil i.e. Soft Rock, Marshy Soil etc.. Length of Pipe : 3 Mtrs. Back filling Compound :2 nos Bags of 25 Kg.

Item Description

providing and erecting Cast iron earth plate size 30 X 30 X 0.35 cms. buried in specially prepared 2.5 Mtr. deep earth pit complete with necessary G.I. strip in G.I. pipe 2 Mtr. long with coupling and G.I. plug for earthing of switch gear, conduit run or power plug etc.

For using salt and charcoal / coke as required for pipe type earthing.

Providing and erecting approved make AMF control panel suitable for following size of 3 phase, 415 V., 50 cycles, A.C. diesel generating set complete of scope as detailed below: 1) Power module: A pair of electromechanically interlocked contactors (for mains and generator) Overload relay for generator contactor Neutral contactor for mains and generator Power socket for connections. 2) Control and metering module: Line voltage monitor. Generator voltage monitor Ammeter 3 items attempt start facility. Air circuit breakers/MCB/MCCB of suitable rating for auto/manual operation. Auto/manual switch. Emergency stop push buttons. Manual start push button. frequency meter. Engine hour meter. Two earthing studs. 3) Protection module: The engine shutdown in the unlikely event of Low lube oil pressure High cylinder head temperature. V belt failure. 4) Indicators with alarm Load on generator. 5) Indicators Load on mains Engine fails to start . Emergency stop battery charger. The AMF Panel of following capacity (C) AMF Control Panel for100 KVA/125 KVA3 phase DG Set

Supplying and erecting XLPE(IS:7098)(I)88 ISI unarmoured copper cable 1.1 KV grade to be erected as directed of following size. (J) 4 core 2.5 Sq. mm

Providing and laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at required depth in existing trench for laying of cable. below ground / road surface for enclosing cable (D)120 mm outer dia.

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or required depth for laying any size of cable or locating the fault all over the run and back filling the same and making the surface as normal ground.

Supply, Installation, Testing and Commissioning of MAIN MOTORISED CURTAIN with Remote Control made out of Horizontal Sliding Arrangement complete with fixing Rails, Brackets and Motorized operation complete with Runners, master Runners, Pullies, 3mm Steel wire rope, 1 HP Motor ( Crompton / Godrej ), 2Nos. Air Breaker Contactors ( Siemens / Schneider / L and T ), 2Nos. Micro Switches for Auto Stop, 3Nos. Push buttons for Forward, Reverse and Stop Positions. The Curtain Material High Quality Velvet (Inovativ / Vimal ) as per approved Colour and make with a Gathering 100 Percentage stiched as per site Condition. Curtain provided with Eyelets at every 200/250 mm for Uniform fixing on to curtain Ttrack / Trollies. The Curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900mm and should be stitched in double gathering. Apprx. Size : 60 FT. X 15 FT.

Supply, Installation, Testing and commissioning of CYCLORAMA SCREEN with fixing 35x35x5mm MS Angle on the wall with MS Angle hold Fasts Secured to the Wall and 40mm Dia 14G MS Pipe welded to it as per site. 40mm Dia Pipe welded to it at 600 centers Vertically at on angle of 45 degree and welding 40mm Dia Pipe Horizontally to it the pipe to be soppoeted away with at 200mm centers by MS Pipe. 12mm Dia MS hooks welded to the both ( Top and Bottom ) The Screen Material PVC Cyclorama Cloth as per approved sample and Fixing by Cotton Doori 610mm thic. Apprx. Size : 30 FT. X 15 FT.

Supply, Installation, Testing and Commissioning of MIDDLE and BACK MOTORISED CURTAIN with Remote Control made out of Horizontal Sliding Arrangement complete with fixing Rails, Brackets and Motorized operation complete with Runners, master Runners, Pullies, 3mm Steel wire rope, 1 HP Motor ( Crompton / Godrej ), 2Nos. Air Breaker Contactors ( Siemens / Schneider / L and T ), 2Nos. Micro Switches for Auto Stop, 3Nos. Push buttons for Forward, Reverse and Stop Positions. The Curtain Material Glazzed Black Cotton Fabric as per approved Colour and make with a Gathering 100 Percentage stiched as per site Condition. Curtain provided with Eyelets at every 200/250 mm for Uniform fixing on to curtain Ttrack / Trollies. The Curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900mm and should be stitched in double gathering. . Apprx. Size : 50 FT. X 15 FT.

Supply, Installation, Testing and commissioning of STAGE WINGS made out of Fixed Wings structure designed as per site Condition and made with MS Suare tube 25mm x 50mm duly Painted In Black Colour With Black Glazed cotton Cloth Both Side Having Manual Moving Facility Complete with required Accessorie for the Rotation of the Wings. The Wings Material Glazzed Cotton Fabric as per approved make and colour with a Gathering of 0Percentage Stitched. Apprx. Size : 15 FT. X 4 FT.

Supply, Installation, Testing and commissioning of Suitable Size Frills made out of fixed Valance Bar 15 Mtrs. Length as per design made out 25 OD mild Steel/MS Pipe Barrel, Supported to hang the Main Valance of the stage system with Matt Black finish Paint. The Frills Material Glazzed Cotton Fabric as per approved Colour with a Gathering of 50Percentage Stitched as per site condition. Apprx. Size : 50 FT. X 4 FT.

Excavation for foundation up to 1.5 mt. depth including sorting out and stacking of useful materials and disposing of the excavated stuff up to all lead.(B) Dense or Hard soil

Excavation for foundation depth from 1.5 mt. to 3.00 Mt. depth including sorting out and stacking of useful materials and disposing of the excavated stuff up to all lead. (C) Hard Murrum

Supplying of Rubble materials. Lead 50 Km.

Filling in plinth with sand under floors including watering ramming, consolidating and dressing complete.

Spreading the stone aggregate for rolling and W.B.M. including filling the interstices to required camber and gradient (excluding spreading of Blindage)(ii) 40mm to 63mm size aggreagates (H.B.)

Providing and laying cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 Machine cut stone aggregate 40mm nominal size ) and curring complete including cost of formwork in (a) Foundation and plinth

Providing and Laying controlled cement concrete M250 and curing complete including the cost of formwork and excluding the cost of reinforcement for reinforced concrete work in (A) Foundation footing base of column and mass concrete

Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations etc. in layers not exceeding 20cm. in depth consolidating each disposited layer by ramming and watering.

Providing and Laying controlled cement concrete M250 and curing complete including the cost of formwork and excluding the cost of reinforcement for reinforced concrete work in Column (D) Columns, Pillars posts and struts upto floor two level

Providing and Laying controlled cement concrete M200 and curing complete including the cost of formwork and excluding the cost of reinforcement for reinforced concrete work in Beam (C) Slabs, Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two level.

Providing and Laying controlled cement concrete M250 and curing complete including the cost of formwork and excluding the cost of reinforcement for reinforced concrete work in SLAB (C) Slabs, Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two level.

Supplying cutting, bending, binding nad placing in position steel as per plan and design and as per ISS 2502 including cost of steel and binding wire for reservoirs/structure only including lift up to 6.00 mt. height or depth below GL for all diameter DoCRS steel all diameter Fe 500 grade confirming to elevant I.S.

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in Superstructure in Cement Mortar 1:5. (1 Cement : 5 fine sand) Extra for brick work in superstructure above plinth level upto floor two level (B) Conventional

Providing 10mm thick cement plaster in single coat on brick/concrete walls for interior plastering upto floor two level and finished even and smooth in (i) Cement mortar 1:3 (1cement:3sand) Extra over items 58 to 64 for finishing with a floating coat of neat cement slurry.

20mm thick sand faced cement plaster on walls up to height 10 mtrs. above ground level consisting of 12mm thick backing coat of C.M. 1:3 ( 1 cement : 3 sand ) and 8mm thick finishing coat of C.M. 1:1 (1 cement : 1 sand) etc. complete.

Providing throating of plaster drip and moulding to R.C.C. Chhajja.

Providing and laying broken China Mosaic Flooring for Terrace using 12mm to 20mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to plain or slope and to be tempered to bring mortar crème out upto surface using white cement including rounding off junctions and extending them up to 15cm. along the wall, clearing with water and oxalic acid etc. as directed.

Providing and mixing Dr. Fixit water proofing material in cement concrete in mix proportion recommended b the manufacturers.

Providing and laying cement concrete flooring 1:2:4 (1 cement :2 course sand : 4 graded stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement (B) 50mm thick

Providing and fixing M.S. grills of required pattern to wooden frames of windows etc. with M.S. flats at required spacings and frame alround, square or round bars with round headed bolts and nuts or by screws (B) ORNAMENTAL GRILL

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth.

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an required shape even shade after thoroughly brushing the surface to remove all dirt, and remains of loose powdered materials.etc complete.

Applying priming coat of over new steel and other metal surface after and including preparing the surface by thoroughly cleaning, oil grease, dirt and other foreign mater and scoured with brushes fine steel wool, scrapers and sand paper with ready mixed priming paint brushing red le

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint, brusing interior to give an even shade including cleaning the surface an even shade including cleaning the surface of all dirt, dust and other foreign matter.

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint including cost of rings, as per IS specification no. 4985/1988 including all local and central taxes, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to the departmental stores and including cost of jointing meterial etc. complete Test pressure 6 kg/cm² 110mm dia PVC pipe line

160mm dia PVC pipe line

Providing and supplying at store or site of work incl. freight, loading, unloading, stacking, insurance and all taxes etc. complete. PVC Elbow 110mm dia

160mm dia

160mm dia (PVC Bend 90º (Fabricated) 6.0 kg.)

Providing and constructing rectangular brick masonry chamber for house connection as per type design in brick masonry in C. M. 1:3 including M100 in foundation M150 in benching inside plastering in C. M. 1:3 and outside plastering in C. M. 1:3 coping in M200 and fixing RCC precast manhole frame and covers, but Excl. supply of manhole and cover etc. complete excl. excavation.

RCC precast M.H. Frame and Cover Manufacture, supply and Delivery at store or at site of work precast RCC M.200 Frame and cover suitable to drainage M.H. and as per type design and Drawing including cost of reinforcement M.S. Angles or Flate, curring mold work etc. House Connection Chamber Light Duty > Frame

> Cover

Excavation for pipe line trenches for water supply, sewerage line, manhole etc. all with shoring and struting if required as per required gradient and line including safety provisions using site rails and stacking excavated stuff including up to all required lead cleaning the site etc. complete for all lifts and strata as specified. Upto 1.50 mt. depth a) In all sorts of soil and soft murrum

Lowering, laying, fixing and jointing PVC / uPVC / cPVC pipes and specials of following class and diameter including cost of conveyance from stores to site of works including cost of labour, material, cement solvent, giving satisfactory hydraulic testing as per ISI code 110mm dia PVC pipe line

Item Description

160mm dia PVC pipe line

Refilling the pipeline trenches incl. ramming, watering, consolidating disposal of surplus stuff as directed within a radius of 3 km. Refilling as directed

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1 cement :2coarse sand : 4graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1cement : 3 coarse sand :6Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:3 (1Cement : 3coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1Cement :2 Coarse sand :4stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg./ Sq.cm. in Cement Mortar 1:5 (1 Cement: 5Coarse sand) (1) A type depth 0.90 Metre for 150mm diameter sewer.

Drilling of bore well by DTH rig in rocky formation in all talukas of all districts of Zone III. Up to 350 mtr. 225mm Dia.

Providing and Lowering of 225mm dia. x 6 Kg/cm² PVC Pipe confirming to latest ISI including jointing materials.

Providing and fixing bore plug having 100mm height made from M.S. plate with 3 holes at equal distance on circumference for nutbolts type, locking arrangement with nutsbolts and lock nuts of standard make complete. From 5mm thick MS plate suitable for Suitable for 250 mm dia. pipe.

Manufacture, supply and delivery of clamp made from M.S. plate with 3 holes on either side with nuts and bolts of standard make and suitable size. 450 mm x 50 mm x 10 mm flat suitable to 32 mm dia pipe 450 mm x 50 mm x 10 mm flat suitable to 32 mm dia pipe

SITC of 4MP (2688x1520) Outdoor IR network bullet camera, 30 Mtr, Max. 4mp@25/30 fps, 3.6 MM Fixed lens, WDR,3DNR, AWB, AGC, HLC, IR Range 30 Mtr, PoE camera, IP67 weatherproof, CE, FCC, BIS, 1 year warranty

SITC of 4MP (2688x1520) Indoor IR network Dome camera, 30 Mtr, Max. 4mp@25/30 fps, 3.6 MM Fixed lens, WDR,3DNR, AWB, AGC, HLC, IR Range 30 Mtr, Inbuilt Audio, PoE camera, IP67 weatherproof, CE, FCC, BIS, 1 year warranty

Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber insulation.

SITC of 64 Ch. Network Video Recorder, approx. 1024 MBPS bandwidth, H.265/H.264+ smart decoding, support 4/8 SATA up to 4TB Hard drive, 2/4 USB Port, HDMI, VGA, CE, FCC, BIS, 1Yr Warranty

SITC Of 4TB (4000GB) Hard Drive, 5400RPM/5700RPM, 24/7 Operation, For Video Recording, Dynamic Cashe Technology, 1 Year Warranty, CE, FCC, RoHS,

SITC Of 8 Ports Gigabits Smart PoE Switch With 2 Giga Uplink Ports, 4858W PoE Power Budget, WEB/CLI Management, Advances QoS Feature, CE, FCC, 1 Year Warranty,

SITC Of 8 Ports 10/100/1000 Mbps Giga Desktop Switch, Link Indication, Power,

SITC Of Outdoor Power Cable or Aluminium Service Wire for power for PoE Switch, as per site requirements,

SITC Of Outdoor CAT6 Cable for Camera, Solid Bare Copper, 4 Pair CAT6, 24 AWG, PVC Outer Jacket, Double Jacket, Inner Jacket PVC, Every Meter Sequential Marking, Temp: 15+60 C, CE, FCC, ROHs,

SITC Of PVC Conduit Pipe, 25MM, ISI Mark, White Colour, Including Relevant Accessories,

SITC Of RJ45 Modular Plugs, 4 Twisted Pair, 100 Pcs Packs, Transparent Colour, Gold Plating Finished, Operating temp: 40 C to 80C, CE, FCC, 1 Year Warranty,

SITC Of HDMI Cable for Camera Monitoring, 10 Mtr, Gold Plating, 4K, CE, FCC, 1 Year Warranty

SITC Of 55 Inch 300400 NTS Brightness LED TV Display, Resolution: 3840X2160, Refresh Rate: 60Hz, Audio:10W+10W, BIS, 1 Year Warranty,

SITC Of 4U Wall Mount Rack for System Security, Front Glass/Acrylic Door with Lock, Fan Mounting, 5 Amp PDU, Complete Hybrid Powder Coating, Including Tray, Cooling Fan, Mounting hardware,

SITC Of 4U Wall Mount Rack for System Security, Front Glass/Acrylic Door with Lock, Fan Mounting, 5 Amp PDU, Complete Hybrid Powder Coating, Including Tray, Cooling Fan, Mounting hardware,

SITC Of UPS, IGBT based Rectifier, sealed maintained free battery, 1 KVA with 6 Nos Of battery, BIS, 30 Min Power Backup,

SITC Of Camera Junction for Camera and Connector Safety,