CERTAIN B/R WORK SERVICES AT OUTSIDE LOCATIONS INCLUDING SARMAT UNDER AF STATION JAMNAGAR NO 1

Amount

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified

M&L for pre-painted galvalume aluminum Zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof ridges etc fixed with self drilling screws as specified

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) (Fe-410-W(Gde-E-250) quality-B) including distance pieces, cleats etc.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240

S&F rolled mild steel Fe 410-W (Gde-E-250) quality-B in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

M&L for cement concrete Type C2 (1:3:6) (40mm graded aggregate) in foundations filling and mass concrete

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets

S&F false ceiling of Non asbestos fiber cement building boards, manufactured from homogeneous mixture of cement, quartz and cellulose and cured with high pressure steam using auto claving process confirming to IS-14862, of size 600mmx 600mmx 4mm thick fixed over and including anodised aluminium powder coated (minimum thickness of powder coating 50 micron) snap grid frame work of T Section (main & cross member) of size 25mm x25mmx1.5 mm thick in square pattern of grid size 600x600mm....

.......The aluminium frame work will supported on side wall with the used of alumminium 'L' section of size 25x25x1.5mm angles etc. Snap grid shall be supported with hangers of 4mm dia, galvanised iron wire adjusting level fixed to roof slabs/truss etc by means of ceiling cleats made out of galvanised iron flat of size 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed

Taking down chowkhats or frames n.exc 1.5 sq. m each with shutters (without taking off shutters from the frame)

Taking down chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m each with shutters (without taking off shutters from the frame)

S&F solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed

S&F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165

M&L for cement concrete Type B1 1:2:4 (20 mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

S&F in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) three track window (two shutter glazed & one shutters wire gauge) with frame, glazed with 4mm thick tinted glass, and wire gauge with stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm including rubber bead joining cleat for fixing in position, concealed type lock for all two shutter, PVC roller etc all as specified below, complete all as specifed including taking down old window.

(a) Frame (top & side ) section shall of size 92.00x31.75x1.50mm (Section o 20831). (b) Frame (bottom) section shall of size 92.00x31.75x1.50mm (section No 20832). (c) Top & side members of shutter section shall be of size 18.00x40.00x1.55mm (Section No 20738). (d) Shutter interlock section shall be size 18.00 x 40.00x1.45mm (Section 20737) (e)Bottom members of shutter section shall be size 18x40.00x1.55mm (Section No 20736) Note : Section Nos given above are of make Jindal, contractor may use similar setion of other make mention in Appx AB

S&F aluminium (powder coated with approved colour) ventilator, partially glazed and partially louvers, outer frame & mullion fabricated with alumimium section of size 82.50mm x 38.00mmx1.5mm thick (Cat No 20036), half portion glazed with 4mm thick frosted glass including rubber beading & glazing clip, half portion louvers of 80mm wide & 4mm thick frosted glass including alumimium louver patti including SS wire gauge of fixing of 0.36mm dia and 1.40 width of aperture with 25x3mm thick aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position including taking down old ventilator complete Note : Section Nos given above are of make Jindal, contractor may use similar setion of other make mention in Appx AB

S&F in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) door shutter with frame, partly glazed with 5mm thick tinted glass and partly panelled with 9mm thick prelaminated particle board with both side decorative laminated including rubber bead, joining cleat for fixing in position, aluminium door handle 150mm size, aluminium barrel tower bolt 200mm size etc including taking down of old frame with shutter of any size all as specified and directed

(a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4mm (Section No 14021) (b) Vertical members of shutter section shall be of size 85.00 x 44.45x2.00mm (Section No 19560) (c) Top members of shutter section shall be of size 83.50 x 44.45x2.00 mm (Section No 19596) (d) Lock rail (middle member ) of shutter section shall be of size 150.00x44.45x3.00 mm (Section No 19596) (e) Bottom member of shutter section shall be of size 150.00 x44.45x3.10mm (Section 19584) (f) Glazing clip for securing glass of shutters shall be of 0.80mm thick (Section No 19370). Note : Section No given above are of make Jindal, contractor may use similar section of other make mention in Appx AB

S&F flush shutters 35 mm thick , solid core construction, with block board core and plywood face panels, commercial type on both sides

S&F 35 mm thick 2nd class hardwood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats

S&F 30 mm thick 2nd class hardwood, Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

S&F 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed

S&F 100 mm long aluminium anodised, barrel tower bolts of extruded section and fixed

S&F aluminium handles, 150 mm size, cast type, anodised

S&F aluminium handles, 100 mm size, cast type, anodised

S&F cold rolled mild steel butt hinges medium grade 100 mm long

S&F cold rolled mild steel butt hinges medium grade 75 mm long

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete

S&F Door closer hydraulically regulated, designation No.2, universal type, aluminium (extruded body section ) suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surfaces of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of pink primer

Demolition of brickwork or stone/ boulder masonry / PCC block masonry, built in cement or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M&L for pre-cast cement concrete block masonry 1:5:8 (20mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6, complete

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. including removal of debris off the MD land

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4, finished even and smooth without using extra cement

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper over a coat of primer on walls including a coat of cement based wall care putty

M & L for preparation of old existing surfaces of ceiling and applying one coat of Oil Bound Distemper complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide, zinc chrome primer

S&F in repairs stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

Hacking out old broken glass (any thickness, size, quality or description) from metal or wooden frame, glazed with putty or fixed with beads complete

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane

Cleaning and removing all scale and dirt, etc, from tanks of capacity exc 250 & n.exc 500 litres and from mouths of circulating pipes, etc.

Cleaning and removing all scale and dirt, etc, from tanks of capacity exc 500 & n.exc 1000 litres and from mouths of circulating pipes, etc.

S&F in repairs 20 mm bore ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm - 210 gms)

Supply and fix in repair 500 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete.

Supply and fix in repair 1000 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store

Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store

M&L for 15 mm steel water tubes, 'medium grade' galvanized, with all fitting and fixed complete to walls and ceilings or laid in floors

M&L for 20 mm steel water tubes, 'medium grade' galvanized, with all fitting and fixed complete to walls and ceilings or laid in floors

Supplying and laying of 20 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified including taking down old pipes.

S&F in repairs white vitreous china wash hand basin (Flat back) of size 550x400mm fixed on and including new brackets complete excluding taps and waste pipes, but including 32mm size PTMT waste coupling.

S&F in repairs Pillar taps 15 mm size , cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete including provision of lime concrete bedding

S&F in repairs vitreous China wash down water closet pan (pedestal pattern), white (including fixing bolts & P or S trap) and finishing with white cement

S&F in repairs toilet paper holder, brass, chromium plated fixed to walls with chromium plated (CP) brass screws

S&F in repairs plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device

S&F in repairs 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including bracket and connections to pipes and fixing of chain and pull, or lever.

S&F in repairs 15mm size PVC connection with PTMT nuts of length 450mm complete all as specified and directed

S&F in repairs 15 mm size chromium plated bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F in repairs 15 mm size fancy type, chromium plated bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F in repairs 15mm size stop valve, cast copper alloy, CP fancy type with capstan head, screwed down, screwed both end for iron pipes complete

S&F in repairs 15mm size Angle stop valve, cast copper alloy, CP fancy type with capstan head, screwed down, screwed both end for iron pipes or for unions complete

S&F in repairs 20 mm bore dia gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long

S&F in repairs tubular towel rail, aluminium anodised, 20mm dia, D type, 60cm long between flanges

S&F in repairs white vitreous china urinal, Half stall type, including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and incl 60mm long brass screws , pointing around urinal back in cement, including automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed

S&F in repairs 32 mm waste coupling of PTMT (half or full threaded) suitable for urinals, (Minimum weight 45gms)

S&F in repairs stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915 mm x 460 mm with bowl size 410mm x 330mm x 160mm including PVC outlet pipe

S&F in repairs stainless steel grating round 100 mm size.

S&F in repairs cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)

S&F in repairs stainless steel grating round 75 mm size.

S&F in repairs waste pipes (32 / 40 mm dia) suitable for urinals , wash basin and sinks

S&F in repairs health faucet with 1 mtr long easy flex tube in chrome finish & wall hook, complete all as specified. ( Model No ALD-CHR-593 of make Jaquar or equivalent of makes given in Special Conditions / Particular Specifications/ ISI marked as approved by GE)

S&F in repairs plastic sheet covers for water tank, black, closed pattern complete all as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for Non - skid joint free coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including screed bed or bedding layer of cement mortar 1:6, 15 mm thick

M&L for Non - skid joint free coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including screed bed or bedding layer of cement mortar 1:6, 15 mm thick

M&L for dark shade vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including screed bed or bedding layer of cement mortar 1:6, 15 mm thick

M&L for coloured glazed ceramic tiles in vertical surface 300x 200x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, over and including 10mm thick backing coat in cement mortar 1:4

M&L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like set and jointed in cement paste including backing coat in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

M&L for repairing the edge / corner of Chajja / roof projection and similar work by removing plaster width / girth exc 200mm but not exc 300mm and making good with 10mm thick rendering in cement mortar 1:3 to match with existing surface complete all as directed

S&F PVC (SWR) pipes 110 mm bore, single socketed in any length with rubber ring joints fixed to walls including taking down old pipe

S&F PVC (SWR) pipes 75 mm bore, single socketed in any length with rubber ring joints fixed to walls including taking down old pipe

Removal of existing roof treatment consisting of screed bed, tar felts of any description etc, and removal of debris out side MD land complete all as directed and as specified

M&L for screed bed or bedding layer of mortar 10 mm thick in cement mortar 1:4 including mixing only liquid water proofing compound as per manufacturers' instructions and finishing the surface fair and even. Note:- WPC will be measured & Paid separately

Supply only liquid water proofing compound

Material and labour for water proofing treatment by applying one coat of oil base bituminous primer @ 0.3 Kg / Sqm with brush / roller, laying of 3 mm thick APP based polymer modified membrane (mineral finish) reinforced non-woven polyester, weight not less than 3.50 Kg / Sqm and sealing all the over laps 150 mm in length side and 100 mm in width side of membranes laid with torch application complete all as specified and as directed.

Demolition of concrete (un-reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) including removal of debris to a distance exc 1.5 km but n.exc 2 km

M&L for 75 mm thick cement concrete type D- 2, 1:4:8 (40mm graded aggregate) in sub-floors, sub-bases, floors and pavings etc

M&L for machine pressed precast concrete interlocking paver block of approved shape and size of 60mm thickness, with minimum compressive strength of 35N/sqm (M-35 ), without correction factor for chamfering, made in rubber moulds with 0.50mm thick scratch proof lacquer coating on top surface, with white cement and pigment laid over and including 25mm thick sand screed bed complete

Supply and fix in repair mild steel galvanised punched tape concertina coil of loop dia 600 mm (dia of coil when up stretched) with 5 Nos of clips and pitch between the barbs of 24.5mm, fixed to existing angle post strut and tying at three places ie two bottom & one at top with 3.15 mm dia galvanised mild steel wire all as specified and directed by Engineer in Charge. Note:- The punched tape concertina coil shall be stretched to maintain the dia of up stretched coil as 600 mm and number of circles as 52 per coil and shall cover 8 running metre per coil. Measurement shall be the length after laying without stretch.

S&F in repairs galvanized 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolt .including .securing or tying at crossing with and provision of galvanized mild steel wire staples or steel pins etc. as directed ( each line wire to be measured)

High Tech Consruction (BID ID -3082340)

Indice Technologies (BID ID -3082285)

JAYESH TRADING CORPORATION (BID ID -3082834)