SPECIAL REPAIR TO BUILDING NO. P-91 (LOGISTICS COMPLEX) AT NAVAL BASE INS DWARKA OKHA UNDER GE NAVY PORBANDAR

Amount

Demolition of stone/boulder masonry, built in cement mortar incl coping etc all as specified and as directed by Engr-in-Charge.

M & L for walling of Porbandar stone masonry well bonded and solidly hearted built in CM 1:6 complete all as specified .

M&L for walling of except stone masonry well bonded and solidly hearted built in CM 1:6 complete all as specified .

Taking down cement plaster, any description on brick or stone walls, etc. including raking out joints, hacking for keys, scrubbing down with water, etc. and rubbishing off the premises, etc. complete

M & L Rendering 10mm thick in CM 1:6 on fair faces of stone masonry work or concrete surfaces finished even and smooth without using extra cement, Complete all as specified and directed.

M & L Rendering 15 mm thick in CM (1:4) on stone/concrete surface of external walls finished even & smooth with using extra cement incl using integral WPC etc complete (integral WPC will be measured separately.

M & L Rendering 5 mm thick in CM (1:3) on concrete surface of ceiling finished even & smooth without using extra cement etc complete

Supply only integral waterproofing compound

M & L for preparing of newly plastered surface of walls and applying one layer 1 mm of white wall care putty and two coats of oil bound distemper over a coat of primer etc complete

M & L for Preparation of new plastered surfaces in walls soffits, facia roof and applying Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives@ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. at any height including necessary scaffolding etc complete all as specified and as directed by Engr-in-Charge of weather coat primer all as specified.

M & L for peparation of newly plastered surfaces of ceiling and applying three coat of white wash all as specified.

Complete removal of existing treatment of wall ( any no. of layers) and making surface even and smooth to receive two coats of anti fungal weather proof acrylic based paint 100% acrylic over coat of exterior wall primer after preparation of surface of at any height including necessary scaffolding etc. complete all as specified and as directed by Engr-in-Charge

M & L for complete removal of existing treatment with mechanical scrubber on old plastered or un-plastered surfaces of walls and applying two coats of oil bond distemper over 1 mm Birla/JK white putty on walls complete all as specified and directed.

M & L for preparation of old treated surface of ceiling and applying one coat of white wash complete all as specified and directed.

M & L for prepration of old treated surface of wall and applying one coat of white wash complete all as specified and directed.

Taking down chowkhats (without taking off shutter) exc 1.5 sqm but n exc 4 sq. m each including builders hardware

Taking down chowkhats (without taking off shutter) not exc 1.5 sqm each ncluding builders hardware

Taking down aluminium windows/ door frames incl shutters (without taking off shutter) complete of size n exc 1.5 sqm area all as specified

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S & F Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails MS frameshall be covered with heat moulded plain colour PVC C channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain cover PVC sheets for top rail, lock rail and bottom rail on either side and as gap insertfor top rail and bottom rail, panelling of plain of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles, and rails with suitable PVC sheet beading and joined together with solvent cement supplying l and fixed in the frame at site as per specification and drawing.

S & F 2nd class HW rail and style 35 mm Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated

S & F Stainless Steel butt hinges 100mm size medium weight cold rolled mild steel

S & F in repairs 100mm Butt hinges(Size of hinges in mm), medium weight, cold rolled, stainless steel ISI marked, and fixed all as specified.

S & F 300mm long aluminium alloy anodised sliding door bolts complete complete all as specified and directed.

S & F 150mm long (Length of Bolt in mm) Aluminium anodised,barrel tower bolts of extruded section and fixed all as specified and directed.

S & F150mm (Size of Handle in mm) Extruded aluminium alloy handles, fabricated type,anodised all as specified.

S & F in repairs Aluminium (Extruded Section Body) Door closer hydraulically regulated,designation No. 3,universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed all as specified.

S & F powder coated aluminium frame and shutters for doors, windows, ventilators with one or more rebates including joining cleat and necessary fitting (handle, locking arrangement, stoppage) for fixing etc (minimum thickness of powder coating 50 micron) complete all as specified and directed.

S & F 4.8mm thick Sheet glass, ordinary quality with and including neoprene beadings in square nexc 0.5 sq.m in each pane as specified and directed.

S & F 5.5mm thick Sheet glass, ordinary quality with and including neoprene beadings in square nexc 0.5 sq.m in each pane as specified and directed.

M & L in repaiir aluminium deco grill medium grade of mesh size 75mmx75mm with 6mm square anodised aluminium bars fixed with aluminium frame of size 37x19x2mm all as specified

Demolition of PCC in ground floors and pavings n exc 15 cm thickness (below or above round level)

M & L PCC type B-0. 1:2:4 (12.5mm graded aggregate) as in Padding concrete to over roof slab 40 mm thick mixed with WPC 3% by weight of cement, finished even and smooth with using extra cement. (WPC shall be measured and paid separately).

M & L Plain Cement concrete 1:2:4 type B-2( 40 mm graded aggregate) 75mm thick as in plinth protection finished even and fair.

M&L for Concrete bed Type D2 1:4:8 to 150mm dia drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested

M & L cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

M&L for providing cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in copings, benching, and the like including weathering, sightly rounded or chamfered angles and throating as directed.

M&L for providing cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in copings, and the like including weathering, sightly rounded or chamfered angles and throating as directed.

M&L for pre-cast reinforced cement concrete 1:2:4, type B1 (using 20mm graded stone aggregate) as in manhole cover with plain fair surface including chamfers, weatherings, throatings, necessary form work and set in CM (1:6), placed in position complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 Type D-2 using 40mm graded stone aggregate as in sub bases all as specified & directed by Engineer-in-charge.

M & L cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in base and mass concrete to be laid in required slope complete all as specified.

Use of forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade 'A' in plinth protection

Dismantling floor, hearth or wall tiling including cement mortar bedding, and rubbish off the premisess complete all as specified and as directed

M & L for Light shade vitrified ceramic tiles, premium quality, coloured (of approved shade and design) area of each tiles not exceeding 0.36sqm,joint free, as in floors and skirtng, etc. set and jointed in neat cement slurry and joints grouted with pigment to match with shade ,laid over and including 15 mm thick screed bed in CM (1:6) complete all as spec and directed.

-Ditto- as per item no above but in vertical surfaces such as skirting over and including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

M & L for non-skid ceramic coloured tiles (of approved shade and design), 7to8mm thick, of superior quality, square / rectangular (area exceeding 0.11 Sqm but not exceeding 0.18 Sqm) joint free, as in floors, etc.set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match shade of tiles laid over & including 15mm thick screed bed in CM (1:4) complete all as specified and as directed

M & L for coloured Glazed ceramic tiles,of size 450x300x 7 to 8mm thick (approved shade and design) of superior quality fixed on vertical surfaces such as skirting / dado / risers of step etc.,set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles fixed over & including backing coat of 15mm thick plaster in CM (1:4) complete all as specified and as directed

Demolition of stone slabs and tiles of any description or thickness laid, bedded and pointed in any mortar .

M & L 20 mm thick Granite (of any type) work (table rubbed and polished) as in partitions, steps, jambs, pillars, window- cills,cooking platforms, working table and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite

M & L for machine cut kota stone as in flooring, stair case landing. treads of steps etc, 20-25mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified including 15mm thick screed bed or bedding in cement mortar 1:6. all as specified nd directed

M & L for machine cut Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 1:4 cement screed and jointed

S & F in repairs Vitreous China wash down water closet pan (European type) with P or S trap, white colour, fixing bolts, including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc complete

S & F in repairs vitreous china wash hand basin white flat back size size 630x450mm incl 02 Nos angle iron bracket 40x40x5mm bracket CP waste coupling and 32mm dia PVC waste pipe, complete all as specified and direceted.

S & F in repairs Plastic water closet seat and cover, white, closed pattern with flat bottom, and mild steel chromium plated hinging device suitable for European WC all as specified and directed.

S & F in repair 10 litres PVC valveless, syphonic action type flushing cistern, with inlet ball valve, float and handleincloding brackets and PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified

S & F in repairs long shank CP Pillar taps 15 mm dia but fancy type, with capstan heads, screwed down high pressure ,with long screwed shanks and fly-nuts , screwed for pvc pipe and fixed.

S & F in repairs bibtap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe 15mm bore chromium plated (fancy type) all as specified.

S & F in repairs CP Stop valves, crewed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed size 15 mm.

S & F in repairs brass CP Health Faucet with 1.2 mtr long flexible tube and wall hook complete all as specified.

S & F in repair SS soap dish of premium quality with complete fixing accesorises etc complete.

S & F in repairs fancy type brass CP toilet paper holder, fixed to walls with screw etc complete.

S & F in repairs fancy type Brass Chromium plated towel rail, 20mm dia, D type, 60cm long between flanges all as specified.

S & F in repairs PVC connection 600mm long with 2 Nos brass check nuts suitable for 15mm bore of pipe with washer complete all as specified.

S & F in repairs Grating square fitting of size 150mm made in two parts for smell and mosquito proofing with minimum 25 mm water seal of PTMT. (Minimum weight 85gms) complete all as specified.

S & F in repair designer looking mirror of size 1350 x900 mm with back lit and fixed on wall with brass fixing knob complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, including hangers and hanging arrangements, including providing and fixing 12 mm thick seamless calcium silicate ceiling board made out of 1800 x 1200mm size board, comprising of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having Philips head with under head cutter at minimum spacing of 200mm centre to centre, including fnishing the joint of face board with specially formulated jointing compound and 48mm wide fibre tap to provide seamless finish and multi layer design complete all as specified and directed.

Dismantling of water storage tank of exc 500 ltrs & n exc 1000 ltrs capacity complete all as specified and as directed

Disconnecting existing tanks, exe 1000 ltr n exe 2000 ltr setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately)

Cleaning and removing of all scale and dirt, etc, from tanks exc 250 ltrs& n exc 500 ltrs capacity. and from mouths of circulating pipes, etc

S&F 1000 Ltrs Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and as directed

S&F in repair 25 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/20 m m - 2 1 0 g m s /25mm-455gms/ 40mm - 690 gms)

Taking up or down steel tubing of 20 mm bore and connections

Taking up or down steel tubing of 25 / 32 mm bore and connections

S&F Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls,ceilings or in floors etc pipes incl cutting/chases of walls etc 20mm inclluding fitting (such as elbow teen reducers, couplers short pieces, connection uion etc) whatever required as per dmanufacturer's instruction fixed on wall /ceiling complete all as specified.

S&F in Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls,ceilings or in floors etc pipes incl cutting/chases of walls etc 25mm inclluding fitting (such as elbow teen reducers, couplers short pieces, connection uion etc) whatever required as per dmanufacturer's instruction fixed on wall /ceiling complete all as specified.

S&F in Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls,ceilings or in floors etc pipes incl cutting/chases of walls etc 32mm inclluding fitting (such as elbow teen reducers, couplers short pieces, connection uion etc) whatever required as per dmanufacturer's instruction fixed on wall /ceiling complete all as specified.

M & L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps,cills, sunshades, shelves, lintels, etc.;and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth

Dismantling water proofing membrane Textile coverings including frames (if any) and cover fillets (measured flat and not girthed)

Rendering 10 mm thick on fair faces of stone masonry surfaces or concrete surfaces on wall in CM 1:4 finished even and smooth without using extra cement including mixing Integral Water proofing treatment (where ever required as directed by Engineer in charge) complete all as specified and as directed. Note : Water proofing compound will be measured and paid separately).

Water proofing treatment to RCC roof slab including parapet comprising with the following course of treatment / specification from bottom to top:- (a) Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces. (b) one layer of APP based polymeric membrane of approved manufacturer, 3 mm thick, weight not less than 3.6 Kgs per Sqm, reinforced with non woven polyester fabric or weight not less 150 gms per sqm. Polymeric membrane shall be taken to a height of 60 cm 9 minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. Note:- (i) Laying of APP based membrane shall be done by torch on method and as per manufacturer's instructions. (ii) A minimum overlap of 150 mm and 100 mm should be made in the end and sides of the polymeric membrane respectively and all overlaps and joints are properly sealed as per manufacturer's instructions.

Preparation of New/ previously untreated surface of APP membrane and painted with two coat of aluminium paint all as specified and directed by Engr-in-charge

S & F of non woven geotextile fabric 150gsm over APP membrane with necessary fixing arrangement all as specified and directed

Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner and all as per directed by engineer-in-charge.

Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts/scaffolding all complete as per direction of Engineer-in-charge.

Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-in-charge complete in all respect. Epoxy bonding adhesive having coverage 2.20sqm/kg of approved make

Demolition of Reinforced cement Concrete of any description and in any position not otherwise specifically provided for

Demolition of cement Concrete (unreinforced) of any description and in any position not otherwise specifically provided for

Demolition of unreinforced cement concrete other than ground floor in Roofs, floors (other than ground floors), beams, staircases, landing,chajjas and similar suspended work

M & L for nominal mix RCC Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M & L CRS TMT reinforcement bars 10mm and over using cut to length bent to shape as required including cranking bending spirally for hooking ends and binding with and including mild steel wire (annealed not less than 0.9mm dia or securig with clips etc) complete all as directed.

M & L CRS Mild steel TMT bars 8 mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) all as directed.

Dismantling of cast iron or reinforced concrete drain pipes of dia 300 mm or more, jointed in cement mortar and taking out of trenches, if required

Cutting of bituminous/RCC road and sub-base WBM (any thickness) for laying of RCC drain etc complete

Demolition and breaking up drain pipes 150mm (Salt glazed ware, AC or Reinforced concrete) set in cement mortar in floors including excavation and removal of soil complete all as specified and directed

Reinforced cement concrete pipes 450mm, class NP3, laid and jointed complete with collars

M&L for reinforced concrete pipe of 150mm bore of pipe, class NP-2, laid and jointed with collars complete all as specified and directed.

Extra for forming fair finished drain or channel 60 cm inner girth in cement concrete using extra cement including forms, moulds mitred / stopped ends etc

Cutting into existing manholes of 150mm internal dia of pipes for connecting new drains, making good to pipe and rendering cutting out existing benching and forming branch channel in PCC (1:2:4) type B-1, smooth finished complete all as specified and directed.

M & L stone kerb of roughly squared stones of size 20cmx30cm dressed so that the maximum depression from straight edge held against the dressed surface shall not exceed 6mm for top and exposed surfaces of sides and 20 mm for the rest of surfaces, jointed in cement mortor 1:6 and struck flush, including embedding stones in the ground to depths indicating and tamping ground around stones and also removing any surplus spoils, etc.

M&L for machine pressed precast concrete rubberised inter locking paver blocks any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new painted surfaces and applying two coat of synthetic enamel on brick, stone, concrete, asbestos cement or plaster surface all as specifed and directed.

Taking down carefully aluminum/copper point wiring (light,fans,socket etc) complete incl battens and fittings such as switch, ceiling rose,light fittings, regulaters, socket etc and making good disturbed surface of wall/floor etc complete all as specified.

M&L for point wring for one light / fan controlled by one switch with 1.5 sqmm nominal area) PVC insulated and PVC unsheathed multi stranded copper conductor cable FRLSH in and including concealed PVC conduit 20 mm dia medium duty ISI marked, including suitable new steel sunken boxes, modular frame and cover plate for fixing of modular switches as per required point in that board, flush to surface for one light point, fan point, controlled by one switch on the same board with other switch or independent including PVC insulated unsheathed 1.5 sqmm copper conductor cable FRLSH connected to common earth duly complete including cutting, chasing the surface and then making good the same in CM 1:6 complete all as specified and directed. (Note : Switches, Sockets etc shall be measured and paid for separately under appropriate items of Sch 'A'

All as per item No 105.00 above but One bell/ buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sq.mm size complete all as specified andas directed.

All as per item No 105.00 above but 5 amps socket outlet on same board board.

All as per item No 105.00 above but One 3 pin socket outlet, 5 Amps,independent board complete all as specified andas directed.

All as per item No 105.00 above but One 3 pin 15 Amp socket outlet with 2.5 sqmm PVC unseathed (FRLSH) wire alongwith 2.5 sqmm green colour wire as earth contuinity conductor for 15 amps switch socket combination outlet on independent board complete all as specified and directed.

All as per item No 105.00 above but but one AC Point with 4 sq mm PVC unseathed (FRLS) wire along with 4 sq mm green colour wire as earth contuinity conductor connected to common earth dolly complete all as specified & as directed by engr-in-charge. Note : Seprate circuit of individual point will be drawn from the DB directly for AC Point complete all as specified and as directed.

Supply and Repair/Replacement of Modular switch 1 way 6 Amps, 1 modules 230 volts complete all as specified and directed.

Supply and Repair/Replacement of Modular switch 1 way 16 Amps, 1 modules 230 volts Complete all as specified and directed.

Supply and Repair/Replacement of Modular socket 6A, 2/3 pin combined, 2 modules 230 volts complete all as specified and directed.

Supply and Repair/Replacement of Modular socket 6A/16A, 2/3 pin combined, 2 modules 230 volts complee all as specified and directed.

Supply and Repair/Replacement of bell push 6 Amps, 1 modules 230 volts complete all as specified and directed.

Supply and Repair/Replacement of call bell Multi musical type complete all as specified and as directed

Supply and Repair/Replacement of five step fan Modular regulator 2 module 230 volts complete all as specified and directed.

M/L and Repair/Replacement for Sub main wiring power/circuit using PVC insulated unsheathed FRLS, stranded copper conductor cable 2 Single core of size 6 Sqmm, earth continuity conductor of size 6 Sqmm to be drawn through in and including PVC conduit concealed in walls/roof/floors all as directed by Engineer in Charge.Notes:- (i)Two wires of 6 sqmm and one wire of 6sqmm & PVC conduit shall be measured as one unit.

Supply and Repair/Replacement of ceiling rose surface backelite 65x50 mm having 3 terminal complete all as specified and directed..

Supply and Repair/Replacement of SPN Sheet metal enclosures with plug and socket with Top and MCB SP 20 Amps including taking down the same. all as specified and directed by Engineer - in - Charge.

M&L for taking down and refixing for after Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and as directed.

M&L For breaking the existing wall to make hole for exhaust fan and making good to the disturbed surface of wall complete all as specified and directed at site.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed..

Supply and Repair/Replacement of LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and Repair/Replacement of LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and Repair/Replacement of Supply and fixing LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

Supply and Repair/Replacement of Supply and fixing LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC surface mounting type with high efficiency PMMA diffuser soft glare free light complete with driver, including connecting up with driver three core flexible copper conductor cases of suitable size complete.

Supply and Repair/Replacement of Building street light fitting Endura pearl 30W LED lamp new genaration energy saving & environmental friendly long life made up of pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening separate driver compartment with IP65 protection and impect resistance of IK07,with suitable of GI pipe (light grade) bracket and clamps,nut bolts are fixed on wall/post and all as required and directed Make Havells Cat Part No. ENDURAPEARLSL30WLED757SASYTOPCMP

Supply and Repair/Replacement of MCB DB Single pole and neutral 12 way double door Complete all as specified and as directed.

Supply and Repair/Replacement of TP&N distribution board with double door vertical type TPN DB made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating,suitable for MCCB for capacity 100Amp, 16 KA, Incomer 4 ways 415 Volts made up of CRCA sheet with busbar rating 200 Amps Adjustable thermal (70% to 100%) & Fixed magnetic setting type including grouting in the wall, cutting & chasing etc complete all as specified and directed.

Supply and Repair/Replacement of MCB rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) SP of 5Amp -32Amp current carrying capacity in the MCB DB complete with connection testing and commissioning.complete all as specified and directed by Engineer - in - Charge.

Supply and Repair/Replacement of MCB rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) SPN of 63Amp current carrying capacity in the MCB DB complete with connection testing and commissioning.complete all as specified and directed by Engineer - in - Charge.

Supply and Repair/Replacement of MCCB four pole 415 volts 50 Hz , 100Amps, with rupturing capacity 16 KA complete all as specified and as directed.

Material and labour for taking out Split type Air conditioner 1.0Ton/ 1.5Ton capacity of any make from its original location, removing the dust from body with blower, cleaning the condenser and cooling coil by using water and caustic soda, painting the base tray with one coat of black enamel paint checking all the connections including functioning of metal clad socket/ DP switch function of relay capacitors overload protector thermostat fan motor blade fan blower drum etc. oiling/ greasing of fan motor checking serviceability and refixing it in its original place including testing commissioning for 1.5/2.0 Ton of AC of any make all as specified & directed by Engineer-in-Charge.

M & L of earthing complete with galvanized steel earth plate electrode of size 600 x 600 x 6 mm thick buried directly in ground to a depth not less than 2.25 mtr below the normal ground level with top edge of earth plate not less than 1.50 mtr below the normal ground level and connected to galvanised earth lead wire 4.0mm dia by means of nut, bolt & washer and protected by 40mm dia GI pipe light grade and watering pipe of 20mm dia GI pipes light grade and connected to earth test point including necessary excavation, earth work, PCC chamber (1:3:6) type C-1 and 40 mm thick RCC pit cover in RCC (1:2:4) type B-1 using 6 mm dia MS round bars @ 150 mm C/C both ways all as shown in electrical plate No. 3 of SSR Part-I all as specified and directed.

Making connection of CPVC distribution branch with GI main by providing and fixing tee including cutting and making fusion joint etc.

Supply Repair/Replacement Laying and Testing of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fittings and making connection fixed complete to walls, ceilings floors or laid in trenches etc. of 50 mm dia laid in trenches complete all as specified and directed.

All as per above item No 137.00 but for 25 mm dia.

Supply and Repair/Replacement of CPVC ball valve 50 mm bore all as directed.

Supply and Repair/Replacement of CPVC ball valve 25 mm bore all as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, manholes, etc. or for laying cables/pipes, erecting poles etc. n exc 10 sqm on plan and getting out in soft/ disintegrated rock complete all as specified and directed.

Returning and filling in trenches incl spreading, levelling watering and raming in layer n.exc 25 cm complete all as specified and directed.

Removing of excavated materials n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point.

Removing of excavated materials exc. 1.50 km but n exc. 5 km and depositing where directed as in rock complete.

Supply and install hi wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2 of 2 TR capacity complete all as specified andas directed.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5.0 KVA complete all as specified andas directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor 35 Sqmm 3.5 Core complete all as specified and as directed.

M & L for sand cushioning for LT cable laid in trenches using screened sand of approved quality as per SSR Part-I all as specified & directed.

S & F unreinforced pre-cast concrete cable covers class LV types 2 flat size 250mm x 150mm x 40mm including removal of old covers complete all as specified and as directed.

Supply and laying/jointing GI Pipe medium grade 40mm dia with all fittings laid/fixed on wall/pole or under road/PCC crossing and all as specified and directed.

shree chamunda enterprise

JAY BHARAT METAL SUPPLIERS

BABUBHAI BHIMABHAI PANDAVADRA

OM ENTERPRISE