SPL REPAIR TO LIGHTING SYSTEM, ADDL/ALTN FOR IMPROVEMENT TO DIGITAL AUDIO SYSTEM AND PROVN OF PROJECTOR SYSTEM AT RIMC UNDER GE DEHRADUN.

Amount

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L point wiring with 1. 5 Sqmm PVC insulated unsheathed multi stranded single core copper conductor cable in PVC conduit in concealed wiring duly chases cutting and including making good surface for modular fixtures with 1.5 Sqmm PVC insulated copper conductor earth continuity wire for one light/fan point controlled by one switch complete all as specified and directed.

All as per item No.2 above but for one pin 5 A socket outlet independent point.

All as per item No.2 above but for one pin 5 A socket outlet on same board.

All as per item No.2 above but with 4 Sqmm cable for one 6 pin 15A socket outlet point on independent board.

M&L point wiring (Modular wiring) for with 1. 5 Sqmm PVC insulated unsheathed multi stranded single core copper conductor cable in existing concealed conduit with 1.5 Sqmm PVC insulated copper conductor earth continuity wire for one light/fan point controlled by one switch.

All as per item No 6 above but for one pin 5 A socket outlet independent point.

All as per item No 6 above but for one pin 5 A socket outlet on same board.

All as per item No 6 above but with 4 Sqmm cable for one 6 pin 15A socket outlet point on independent board.

S&F ceiling rose surface Bakelite 3 terminals of size 65x25mm complete all as specified and directed.

S&F switch modular 6 Amps 230 Volts one way switch complete all as specified and directed.

S&F Socket modular 6 Amps AC 230 Volts 2/3 pin combined 2 modular type complete all as specified and as directed.

S&F Socket 6A/16 Amps-2/3 pin combined AC 230 Volts modular type complete all as specified and as directed.

S&F Switch modular type AC 230 volts 16 Amps one way complete all as specified & as directed.

S & F Modular Fan Regulator electronic rotary,0-4 steps step type 100 Watt, 240 Volt 50 Hz hum free 2 module complete all as specified and directed.

S&F modular bell push 6 Amp one module one way complete all as specified and directed.

S&F GI sunken box with flush metal GI box 1 module suitable for modular switches including plastering, making good disturbed surfaces of wall, painting to match the existing finishes complete all as specified and directed.

All as per item No 17 here in above but 2 module.

All as per item No 17 here in above but 3 module.

All as per item No 17 here in above but 4 module.

All as per item No 17 here in above but 6 module.

All as per item No 17 here in above but 8 module.

S&F repair combined cover plate white 1 module suitable for modular switches complete all as specified and directed.

All as per item no 23 here in above but 2 module

All as per item no 23 here in above but 3 module

All as per item no 23 here in above but 4 module

All as per item no 23 here in above but 6 module

All as per item no 23 here in above but 8 module

S&F LED light fitting Recessed zigbee enabled wireless communicating Downlighter (22w/2200 lumens) with an ability to be remotely controlled and on/off/dim through an App ,provide data on health to a central controller in a wireless manner. It can be controlled through a wireless switch and function with wireless sensors. Luminaire efficacy should be =100 lm/w, SDCM ≤5 , CRI>80 , life class of 50,000 hours(70% lumen maintenance @ Ta = 45°C) with an electronic inbuilt BIS certified driver. Dimensions -Cut Out : 175 mm ,Outer rim : 185 mm ,Height : 80 Mm. complete all as specified and directed.

S&F Wireless Switch Zig Bee Green Power . Indoor distance that can be covered is typically 10m. for line-of sight installations. No wiring and covered is typically 10m. for line-of sight installations. No wiring and power connections required so easy to install and maintenance free The devices can be linked into for example a network formed with Zig bee mesh network. The devices are easy to install and use. Device UID8450 has switch and dim functionality. Dimension 97×86×22 mm (8450) with an RF range 10m complete all as specified and directed.

Supply & Install of Software system Pro Site Enablement v50 (includes Gateway, Identity Management, App, Installer. Portal Subscription, version control etc.): Supports < 100 Luminaries complete all as specified and directed.

S&F LED strip light in 5 meter length with system efficacy of 90lm/watt & typical efficacy 800lm/meter. Color consistency of the strip (SDCM) must be less than or equal to 3 and CCT should be 3000K & CRI>=80. Lifetime (ta 25C) @L70B50 must be 30K hours. fixture must be have all required report like CB report, LM79, IP test, Thermal test complete all as specified and directed.

S&F Transformer for LED strips 120W 24V DC connected for uniform supply with LED strips, all as specified and directed.

S&F Opal diffused PVC cover of 1meter for LED strip to have much lesser glare fixed with connectors all as specified and directed. Make Philips : or equivalent to Wipro/Havells/ Crompton

S&F "U" type Metallic track of 1 meter lengthx12mmx12mm ( to install the LED strip on any surface of wall/ceiling/floor with necessary connecting accessories complete all as specified and directed.

S&F Mounting clip to fix the LED strip on wall/ceiling/floor/grooves complete all as specified and directed.

S&F Connectors for between LED strips after cutting as per site requirement complete all as specified and directed. Make Philips : or equivalent to Wipro/Havells/ Crompton

S&F End cap used after cutting of LED strips as per site requirement complete all as specified and directed.

S&F LED wall mounted luminaire die cast alluminium housing and frosted glass embedded with EXIT (Colour - Red) sign complete all as specified and directed.

Taking down old exhaust fan from the wall carefully and deposited to MES Yard complete all as specified and directed.

S&F in replacement exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m, complete with louvers, shutters and connecting up ceiling rose to connector block of fan including making of holes and grouting of nuts and bolts PCC (1:2:4) B-1 block including taking down old metallic exhaust fan complete all as specified and directed.

Taking down old air circulators from the wall carefully and deposited to MES store Yard complete all as specified and directed.

S&F decorative 5 star rated Ceiling Fan 1250 mm 3 Blade , dust free, low noise, Pearl White colour, Motor Speed: 350 RPM, Dust and Mark Resistant Coating Strong Aerodynamic profile blades for silent operation, 18 pole high torque motor, Power Consumption: 80 W, Air Flow: 260 cmf, Number of Speed Settings: 4, with connecting accessories and fixing with wall including necessary fixing arranging all as specified and directed. Make Havells Stealth Air Model (Ivory colour) or equivalent Bajaj/Usha/Crompton

Taking down old u/s DB/main switch/Metal clad box of any size complete with MCBs and removing unserviceable materials out of site complete all as specified and directed.

S&F Vertical DB DP 4 way double door with 200 Amp rated bus bar including MCCB, 4 pole, 100 Amp breaking capacity 36 KA with enclosure complete all as specified and as directed. Make Indo Asian Part No 810359, MCCB Part No 830082 or equivalent

S & F sheet metal enclosure TPN for DB's when MCB's to be used 8 way with 200 amps bus bar and double door complete all as specified and directed.

S&F Residual Circuit Breaker (RCOB) for earth leakage, overload & short circuit protection 4 pole 30 MA of capacity 63 Amps complete all as specified and directed.

S&F Sheet metal enclosure SPN for DB's when MCB's to be used 8 way with 200 amps bus bar d/door complete all as specified and directed.

S&F Residual Circuit Breaker (RCOB) for earth leakage, overload & short circuit protection double pole 30 MA of capacity 40 Amps complete all as specified and directed.

S & F MCB TPN 32 Amps, 440 Volts,10 KA 'C' series with all incoming/outgoing connections with proper size of lugs complete all as specified and directed.

S&F MCB TP 32 to 40 Amp , 440 Volts,10 KA 'C' series with all incoming/outgoing connections with proper size of lugs complete all as specified and directed.

S & F MCB SPN 32 Amps,240 Volts,10 KA 'C' series with all incoming/outgoing connections with proper size of lugs complete all as specified and directed.

S&F MCB SP 32 Amps,240 Volts,10 KA 'C' series with all incoming/outgoing connections with proper size of lugs complete all as specified and directed.

M&L for sub main wiring with 3 runs (1 run for Phase, 1 run for neutral & 1 run for earth, copper conductor of standard approved colour code of 1.5 Sqmm single core, PVC insulated, unsheathed, multi stranded copper conductor FRLS cable 1100 volts grade drawn through and including concealed wiring with PVC conduit pipe of medium duty not less than 15 mm dia including necessary steel conduit specials and conductor and connecting with suitable size thimble, and making good surface of disturbed wall/ceiling/floor as match with existing complete all as specified and directed. Note:-3 runs of 1.5 Sqmm size PVC copper cable, and one run of PVC conduit shall be measured as one unit length.

All as per item No 54 here in above, but 3 run of 2.5 Sq mm copper conductor. Note:-3 runs of 2.5 Sqmm size PVC copper cable, and one run of PVC conduit shall be measured as one unit length.

All as per item No 54 here in above, but 3 run of 4 Sq mm copper conductor . Note:-3 runs of 4 Sqmm size PVC copper cable and one run of PVC conduit shall be measured as one unit length.

All as per item No 54 here in above, but 3 run of 6 Sq mm copper conductor. Note:-3 runs of 6 Sqmm size PVC copper cable, and one run of PVC conduit shall be measured as one unit length.

All as per item No 54 here in above, but 3 run of 10 Sq mm copper conductor. Note:-3 runs of 10 Sqmm size PVC copper cable, and one run of PVC conduit shall be measured as one unit length.

All as per item No 54 here in above, but 6 run (3 run for Phase, 1 run for neutral & 2 run for earthing for earth, copper conductor of standard approved colour codes) of 10 Sq mm copper conductor wire drawn through PVC rigid conduit not less than 32 mm dia . Note:-6 runs of 10 Sqmm size PVC copper cable, and 1 run of PVC conduit shall be measured as one unit length.

M&L for earthing complete with galvanised steel earth plate electrode 60 x 60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point complete all as specified and directed or indicated including testing on completion.

Taking down old sub main wiring of any size complete all as specified and directed.

Provision of Stage Lighting to the Thimayya Auditorium with following lighting & accessories; complete all as specified and directed.

Providing and Fixing of 200W LED Focusing Imaging Light Power Supply AC100-240V/ 50-60HZ Light Source 56 (3030) or (3535) 3-5W white LED light source Light Source Power 200W Total Power 240W Color Temperature 3200K or 5600K Color Rendering Index 92% or more Dimming Mode DMX signal dimming or manual button dimming Control Channel 1 channel Focusing Mode manual knob sliding focus Light Angle adjustable from 10-20° Working Environment 0°- 40°C (32°-104°F) Protection Level IP20 , including hanging/mounting arrangement .

Providing and Fixing of 200W LED Spotlight (Color Temperature Adjustable) Power Supply AC100~240V, 50/ 60Hz Power 220W Light Source Highly indicated COB LED lamp beads Color Rendering Index Ra>94 Light Source Life 100,000 hours Color Temperature 3000K-6000K adjustable Control Panel LCD display four buttons Beam Angle 15-60 degree Manual zoom Dimming 0-100% linear dimming Heat Dissipation Method copper tube radiator Channel Mode /4CH Control Mode DMX512 control/ manual control Working Temperature -25°C.

Providing and fixing 54 LEDs 3W 4 digital display. There dimmer manual mode, running, strobe, speed adjustable, adjust the data with a power saving, boot automatically recover data. DMX 512 protocol - 6 DMX channels Main dimmer , RGB color changing , Strobe effect, Auto play with internal programs , Master/Slave function, Stand alone mode . Power supply: AC 100V-AC240V 50/60 Hz. Light power connect maximum range 15pcs to 30pcs. Consumption: 160W .

Providing and fixing Revolving head Voltage 110v~240v ,Number of Bulbs 1, Channel 16 Chs / 20 Chs, Frequency 50-60hz ,Average Lifespan 2200 H, Color 14 color blank color wheel.

Providing and Fixing of LED type strobe lights.

Providing and Fixing of LED COB wash light 150w Working Temperature(℃): 20 - 50 IP Rating:IP20 for indoor Emitting Color: COB RGB Lamp: 150W, R,G,B Input Voltage(V):AC100-240V 50/60Hz CRI (Ra>): 90 Working Lifetime(Hour):100000 Certification: CE, FCC, ROHS Control signal: DMX DMX Channel:6.

S&F DMX Splitter Supply and fixing of 1 in 8 Out DMX Splitter.

S&F Fog Machine ,Remote Controllable, DMX channel port Power supply: AC220~240V,50Hz, AC100~240V,60Hz(Optional), Power consumption: 1500W Fuse: 10A /15A,Warm up time: 10 min, Tank capacity: 2L,Output: 5600cuft/min Remote control distance: 25m,Wire control distance: 1.5m,Temperature: 270-310 degree Dimension: 440×300×220 mm, Packing size: 530×340×230 mm,N.W:6 Kg, G.W: 7 Kg complete all as specified and directed. Make - BSS/MSS/NSC

S&F Mini Pearl Lighting Controller 2, Voltage:AC 110V-240V/50~60Hz. N.W(1piece):14 Kg Size(1piece):550×460×350 mm. Mini pearl 1024 can control 96fixtures at the same time. The controller can read the pearl's fixture library format(r20), Inside dozens of effect shapes,also can running 10 scenes.

M&L for DMX point wiring all as specified .

M&L Wiring with 4 core 4 MM wire fixed with light channels for power points.

Supply & install, System Configuration with the Dimmer system.

S&F MCB with DBs for the control system of stage lighting system.

Supply & delivery of FOH left & Right 5.1 Surrounding House Speakers Sys with following specification:- 2 x 10” Full Range, reflex tuning line array , Impedance 32 Ohm, Power Handling (AES)400 Watts, LF / 100 Watts HF (continuous) (continuous)Max. Power Handling (AES)800 W LF / 200 W HF (prog) 1600 W LF / 400 W HF (peak 10 ms)Sensitivity 2.83V / 1m96 dB LF / 110 dB HF Max. SPL119 dB cont. 125 dB peak LF 130 dB cont. 136 dB peak HF Frequency Response (±3dB)55 Hz - 20 kHzDispersion100° x 10° per cabinet, 2 x 1” CD on Planar Wave Manifold Crossover Passive - 1.2 kHz Active - * LPF 1.3 kHz / HPF - 55 Hz Full range / 100 Hz MH complete all as specified and directed. Approved Make: OHM/Martin Audio/British Acoustics/D&B

Supply, Install, Testing & Commissioning of Ground Stacked Subwoofer Passive 2 x18 inch sub-woofer, Frequency Response:47HZ-190KHZ , Max SPL 143 DB, Connector ions- input/Link Speak on rated power 2400 watts nominal impedance -4 OHMS , LF driver -18 inch low frequency, Enclosure Birch Plywood complete all as specified and directed. Approved Make: OHM/ British Acoustics/ OSL/ Martin Audio

Supply, Install, Testing & Commissioning of SIDE Fills Passive 12 inch mid / high speaker, Frequency Response: 57 Hz - 26 kHz (-10dB), 90 Hz - 24 kHz (±3 dB), Continuous SPL: 114 dB, Program SPL 120 dB. Power Handling: 250Watt cont. IEC268 AES, Maximum Power Handling: 500 Watt prog. / 1000 Watt peak, Impedance Nominal: 8 ohm, Dispersion Nominal: 120° x 40° (hor. x vert.), or better complete all as specified and directed. Approved Make: OHM/ British Acoustics/ OSL/ Martin Audio

Supply, Install, Testing & Commissioning of Stage monitor 15" High Power Powered Stage Monitor with Critical Performance Indicators: Max SPL @ 1m: 132 dB, Frequency Response (–3 dB): 50 Hz – 17 kHz, Coverage Angle (H x V): 80 x 50, Transducers: 15" low frequency woofer with 44 mm PET high frequency driver, Inputs: 2 x Mic / Line Input (XLR/ TRS Jack), 1 x Line Input (XLR / RCA), Mounting Options: M10 Fastening Points, 35mm Pole Socket, Amplifier Power: Class H, 500W (1000W Peak) complete all as specified and directed. Approved Make: OHM/ British Acoustics/ OSL/ Martin Audio

Supply, Install, Testing & Commissioning of Control room & Green Room Monitor 8" Powered Control Room Monitor with Critical Performance Indicators: Max SPL @ 1m: 123 dB, Frequency Response (–3 dB): 64 Hz - 20 kHz, Coverage Angle (H x V): 90 x 60, Transducers: 8" low frequency woofer with 25 mm PET high frequency driver, Inputs: 1 x Mic / Line Input (XLR/ TRS Jack), 1 x Line Input (RCA), Mounting Options, M10 Fastening Points, 35mm Pole Socket, Amplifier Power: Class AB, 250W (500W Peak) complete all as specified and directed. Approved Make: OHM/ British Acoustics/ OSL/ Martin Audio

Supply, Install, Testing & Commissioning of FOH system Array Frame Set of 3 Flying Eyes complete all as specified and directed. Approved Make: OHM/ British Acoustics/ OSL/ Martin Audio

Supply, Install, Testing & Commissioning of Bracket for Control Room & Green Room Monitors Wall Mount Bracket for Control Room Monitors complete all as specified and directed. Approved Make: MyStand/ British Acoustics/ OSL/ LAcoustics/ D&B

Supply, Install, Testing & Commissioning of Bracket for mounting SIDE Fills on Wall, Ceiling Cradle, complete with Hand wheels for Leap Fills complete all as specified and directed. Approved Make: OHM/ British Acoustics/ OSL/ Martin Audio

Supply, Install, Testing & Commissioning of 2 Channel analog Amplifier, 1500 Watts @ 4 ohms Audio Power Amplifier, Toroidal or better complete all as specified and directed. Approved Makes: Powersoft/ British Acoustics/ OSL/ OHM/ Lacoustics/ D&B

Supply, Install, Testing & Commissioning of 2 Channel analog Amplifier, 2000 Watts @ 4 ohms, Audio Power Amplifier, Toroidal or better complete all as specified and directed. Approved Makes: Powersoft/ British Acoustics/ OSL/ OHM/ Lacoustics/ D&B

Supply, Install, Testing & Commissioning of 32 Channel Mixer 24 Channel Analogue Mixer complete all as specified and directed. Approved Makes: Mackie/ British Acoustics/ OSL/ Yamaha

Supply, Install, Testing & Commissioning of 33 Meter Snake Cable minimum 32 Channel with Drum of Interface Box & Necessary Connectors complete all as specified and directed. Approved Make: Hawk / Sommer / AWI/Krystal/LYNQ

Supply, Install, Testing & Commissioning of Audio DSP 2 inputs x 6 outputs, speaker management system, with AES inputs, USB inputs, or better complete all as specified and directed. Approved Make: OHM/ British Acoustics/ OSL/ Martin Audio

Supply, Install, Testing & Commissioning of Equalizer for Stage Monitors Dual Channel 31-Band Equalizer, 1/3-octave Constant Q frequency bands, Switchable boost/cut ranges of ±6 or ±12 dB, Front panel bypass switch, ±12 dB input gain range, XLR and TRS Inputs and Outputs, Frequency Response of <10Hz to >50kHz, Dynamic range of greater than 108dB complete all as specified and directed. Approved Make: dbx/BSS/Klark Tecknik or Equivalent

Supply, Install, Testing & Commissioning of Corded Vocal Microphone High-performance Vocal Microphone with adapted sensitivity for deep vocals, Type Dynamic, Frequency Response 24 Hz - 15 Khz, Polar Pattern Car diode, Sensitivity –51 dBV/Pa (1.85 mV), Impedance 600 Ω, Max SPL 168 dB, 1 kHz at 1% T.H.D., Connector Three-pin balanced XLR complete all as specified and directed. Approved Make : OSL/SHURE/Rode/Nueman

Supply, Install, Testing & Commissioning of Corded Instrumental Mic Transducer type: Dynamic, Operating principle: Pressure gradient, Polar pattern: Cardioid, Frequency response: Close miking 50 - 17,000 Hz Distant making (measured at 1 m) 80 - 17,000 Hz, Open circuit voltage: 2.4 mV/Pa (-52.5 dBV) ±3 dB, Nominal impedance: 600 Ω, Load impedance ≥ 2 kΩ, Connection: 3-pin XLR or better Approved Makes: DPA/ OSL/ Shure/ Nuemann

Supply, Install, Testing & Commissioning of Podium Misc Condenser gooseneck misc (cardioids), black, length: 500 mm (20''), two flexible segments, 3-pin XLR male, with pre-amplifier, windscreen included & with Microphone base, 3 pin XLR, push button complete all as specified and directed.Approved Makes: DPA/ OSL/ Shure/ Nuemann

Supply, Install, Testing & Commissioning of Antenna Distribution System Set for the Microphone System, Complete with 2 Flag Antennas & Power Unit complete all as specified and directed. Approved Makes: DPA/ OSL/ Shure/ Nuemann

Supply, Install, Testing & Commissioning of Speaker Cable 4 square mm, 2 core, speaker cable or better Recessed into pvc conduit piping Approved Makes: LYNQ/ Belden/ AWI/ Klotz complete all as specified and directed.

Supply, laying , connecting & Testing of Signal/ Microphone Cable 6 mm 2 core shielded wire complete all as specified and directed. Approved Makes: LYNQ/ Belden/ AWI/ Klotz

Supply, connecting & Testing of Connectors, XLR Male Female, 1/4 inch Phono Jack for connecting the signal/microphone cables attachment complete all as specified and directed. Approved Makes: Nuetrik/ Amphenol/ LYNQ

Supply, Install, Testing & Commissioning of Microphone Stand (Big) for placing the microphones complete all as specified and directed. Approved Make: Mystand/ Ultimate/ Hawk or Equivalent

Supply, Install, Testing & Commissioning of Microphone Stand (Small) for placing the microphones complete all as specified and directed. Approved Make: Mystand/ Ultimate/ Hawk or Equivalent

Supply, Install, Testing & Commissioning Equipment Rack 16RU Rack made upon Metallic frames complete all as specified and directed. Approved Make: Generic/ Custom Equivalent

Supply, Install, Testing & Commissioning of LASER PROJECTOR System with following connecting accessories complete all as specified and directed.

Flexible Laser Projector 9,000-lumen WUXGA performance with Key Specs as below: 01 No.

Projection System: 3LCD Technology, CD Panel: 1.03 inch with C2 Fine Color Light Output: 9,000 Lumen- 6,300 Lumen (economy) In accordance with IDMS15.4 White Light Output: 9,000 Lumen - 6,300 Lumen (economy) In accordance with ISO 21118:2012 Portrait Colour Light Output: 9,000 lm

Portrait White Light Output: 9,000 lm

Resolution: WUXGA, 1920 x 1200, 16:10

High Definition: 4K enhancement

Aspect Ratio: 16:10

Contrast Ratio: 2,500,000 : 1

Native Contrast: 2,000 : 1

Light source: Laser

Laser Light source: 20,000 hours Durability High, 30,000 hours Durability Eco

Keystone Correction: Manual vertical: ± 45 °, Manual horizontal ± 30 °

Colour Reproduction: Up to 1.07 billion colours

Throw Ratio: 1.57 - 2.56:1

Zoom: Motorized, Factor: 1 - 1.6

Projection Lens Zoom Ratio: 1.57 - 2.56 : 1

Lens: Optical

Lens Shift: Motorized - Vertical ± 60 %, horizontal ± 18 %

Lens position memory: 10 positions

Screen Size: 60 inches - 500 inches

Projection Distance Wide: 2 m - 17.2 m

Projection Distance Tele: 3.3 m - 27.8 m

Projection Distance Wide/Tele: 1.99 m - 27.77 m

Projection Lens F Number: 1.8 - 2.5

Projection Lens Focal Length: 36 mm - 57.35 mm

Projection Lens Focus: Motorized

Interfaces: Stereo mini jack audio in (3x), Stereo mini jack audio out, HD Base T, BNC in, HDMI in, DVI in, VGA out, VGA in, Wired Network, RS-232C, USB 2.0 Type B (Service Only), HD-SDI, Wireless LAN b/g/n (2.4GHz) (optional) = 01 No.

Security: Kensington lock, Security bar, Wireless LAN unit lock, Wireless LAN security, Password protection

Other features: 4K enhancement, Absolute Black, Auto Calibration, Customizable user logo, Frame interpolation, Integrated camera for image calibration & image capture, Lens position memory

Video Color Modes: Cinema, Dynamic, Presentation, DICOM SIM, Multi Projection, BT709

Projector control: via: AMX, Creston, Extron

Power consumption: 626 Watt, 512 Watt (economy), 0.3 Watt (standby), On mode power consumption as defined in JBMS-84 554 Watt Heat Dissipation: 2,128 BTU/hour (max)

Product dimensions: 586‎ x 492 x 211 mm (Width x Depth x Height) Product weight: 23.7 kg

Noise Level: Normal: 37 dB (A) - Economy: 30 dB (A) (4K enhancement OFF)

Supported Temperature: Storage -10° C - 60° C

Projector LENS should be designed for thronging image up to length 140(+/-) 20 Feet Make - Sony/Hitachi/Epson

Middle Throw Zoom Lens for Position Flexibility 01 Nos.

Interchangeable lens — for Pro L projectors up to 20,000 lumens

Wide lens shift — for added flexibility High-quality design — up to 1000" screen size support; 2.0 to 2.1 F-number; 14.8 mm to 17.7 mm focal length Zoom ratio — 1 to 1.6 Weight — 4.2 lbs (1900 g)

Up to 8,000-lumen projectors — WUXGA/WXGA 2.16 to 3.48 throw ratio; lens shift—vertical: -67 percent to +67 percent, horizontal: -30 percent to +30 percent 9,000- to 20,000-lumen projectors — WUXGA 1.57 to 2.56 throw ratio; lens shift—vertical: -60 percent to +60 percent, horizontal: -18 percent to +18 percent Native 4K projector — 1.52 to 2.47 throw ratio; vertical: -58 percent to +58 percent, horizontal: -16 percent to +16 percent Make : Sony/Hitachi/Epson

Supply, Install, Testing & commissioning of 4K Switcher 4 HDMI inputs, 1 HDMI Output with de-embedded analog audio, 2K and 4K support, Min. data rate data rate of 17.82Gbps, HDTV Compatible, HDCP 2.2 & HDR10 Compliant, Automatic Switching, 1 Unbalanced Stereo Audio: On a 3.5mm mini jack, Controllable through contact closure switches, etc complete all as specified and directed. Make : Lightware/ Kramer/RGB Spectrum = 01 No.

S& Fixed Screen sheet with Dimensions - 40'x22' - Perforated/Plain for the projector complete all as specified and directed. =880 Sqft

Supply Install, Testing & Commissioning of Power Amplifier having -Power Output-3000W Max., 2500W RMS at 10% THD 2300W RMS at 5% THD, 2150W RMS at 2% THD, Output Regulation-≤ 2 dB, No load to full load at - 1kHz, Input Channels- 1 × Line 200mV/20kΩ balanced, 10kΩ unbalanced, 1 × Line 1V/20kΩ balanced, 10kΩ unbalanced. Make - AHUJA/JBL/Brish Aucostic/CROWN

Supply Install, Testing & Commissioning of Outdoor Speakers having , Input Power-30W RMS, Power Taps on 100V-30/20/10/5W, Impedance- 330/500/1k/2kΩ ,Frequency Response-120-15,000Hz, SPL at 1kHz (1W/1m)-94dB, Dimensions-Ø175 × H256 complete all as specified and directed. Make - AHUJA/JBL/Brish Aucostic/CROWN

Supply Install, Testing & Commissioning of 6 channel Audio Mixer with MP3 Player/Recorder with USB Reader, Bluetooth complete all as specified and directed. Make - AHUJA/YAMAHA/SOUND CRAFT

Supply Install, Testing & Commissioning of Indoor Wall Mount Speakers having , Input Power- 6W RMS, Power Taps on 100V-6/3/1.5W Impedance- 1.6k/3.3k/6.6kΩ, Frequency Response- 60-15,000 Hz, SPL at 1kHz (1W/1m)-92dB,Dimensions-W262 × H262 × D128 mm complete all as specified and directed. Make - AHUJA/JBL/Brish Aucostic/CROWN

Supply Install, Testing & Commissioning of Power Amplifier having -Power Output-415W Max., 325W RMS at 10% THD, 240W RMS at 1% THD ,Output Regulation-≤ 2 dB, No load to full load at 1kHz, Input Channels-3 × Mic 2.5mV/4.7kΩ (unbal.), 2 × Mic 2.0mV/2kΩ (bal.), 1 × Line 1V/50kΩ (Bal.), 2 × Aux 100mV/470kΩ, 1 × Telephone 150mV/10kΩ Frequency Response-50-15,000Hz ±3dB, Signal to Noise Ratio-60dB, Tone Controls-Bass: ±10dB at 100Hz, Treble: ±10dB at 10kHz Output-Preamp 200mV/600Ω (Unbal.), Line 1V/1kΩ (Bal.), Monitor 5V/8Ω Speaker Output-4Ω, 8Ω, 70V & 100V, Digital Player-MP3 Player with USB, SD / MMC Card Reader & Bluetooth Make - AHUJA/JBL/Brish Aucostic/CROWN

Supply Install, Testing & Commissioning of Paging Microphone having -Frequency Response-50-10,000Hz Sensitivity-2.0mV/Pa, Impedance-600Ω complete all as specified and directed. Make - AHUJA/AKG/SHURE

M&L for Wiring & installation 2 core armored PVC coated 1.5 mm complete all as specified and directed. Make - PolyCab/Havells/ Finolux/KEI/V guard

Note for srl item No.63 to 96 of BOQ:- Contractor shall execute the MOU (Memorandum Of Understanding) on non judicial stamp paper of Rs 100.00 with OEM or their authorised dealer for executing the work of item Nos 63 to 96 and work shall be caried out only through OEM or their authorised dealer. Contractor shall submit the MOU to the GE before commencement of work for approval. The leaflet and technical brochure shall also be submitted to GE for approval of product.

MOHAN LAL GUPTA