Implementation of Micro Irrigation System (Drip Irrigation System) of at Droneshwar Pick Up Weir of Machhundri Irrigation Scheme At-Village Dron, Taluka Gir Gadhada, District Gir Somnath.

Name of Work :- Implementation of Micro Irrigation System (Drip Irrigation System) of at

Droneshwar Pick Up Weir of Machhundri Irrigation Scheme At-Village Dron, Taluka Gir Gadhada,

District Gir Somnath

BILL OF QUANTITIES

Percentage Rate Tender (Up to INR 50 Cr. )

Item Description of Item (with brief Quantity Unit Rate Amount

No specification and reference to book of

specifications)

1 Providing and constructing cofferdam in 6903.00 Cum 426.660

river basin including excavation ,filling,

middle portion with soil (in empty

Cement/Gunny bags) to the entire

satisfaction of EIC till completion of the

work including dismantling coffer dam

after completion of the work as directed

2 Excavation in all sort of strata and 4780.00 Cum 74.000

formations incl. depositing the unuseful

excavated stuff as and where directed

incl. sorting and stacking useful

materials in measurable conditions as

directed upto 200mt lead and all lift etc.

complete incl. dewatering. (A) IN

OVERBURDEN INCL. HARD MURRUM.

3 Dewatering for earthen dam and allied 1000.00 HP/ 23.000

works, foundation areas, pits, trenches Hr

etc incl. cost of pumping machineries,

pipe lines, labours diesel/electricity/DG

set, etc complete.

4 Providing & Laying in position 30.00 Cum 4624.000

controlled cement concrete using

cement sand & crushed metal aggregate

by machine mix incl. necessary

formworks, compaction by mechanical

vibrator curing as directed with all lead

and lift etc complete. Excluding the cost

of steel. training wall, side wall and

general purpose. C) Concrete grade M-

20 and MSA-40mm(Graded)

5 Providing and laying in position Ready

Mixed M-300 grade concrete for

reinforced cement concrete work , using

cement content as per approved Design

Mix manufactured in fully automatic

batching plant and transported to site of

work in transit mixer for a lead up to

kms having continuous agitated mixer,

manufactured as per mix design of

specified grade for reinforced cement

concrete work including pumping of

R.M.C. from transit mixer to site of

laying, excluding the cost of centering

shuttering finishing and reinforcement

including cost of admixtures in

recommended proportions as per IS:

9103 to accelerate/ retard setting of

concrete, improve workability without

impairing strength and durability as per

direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as

per latest IS 456 shall be maintained)

(a) RCC M:30 Quantity 416.57 Cum 5094.090

(b) RCC M:25 Quantity 73.12 Cum 4902.090

(c) RCC M:15 Quantity Plum Concrete 20.50 Cum 3828.110

6 Providing, cutting, bending, binding and 52.92 MT 76303.000

fixing in position as per drawing .TMT

BAR , reinforcement for R.C.C. works

and anchor bars incl. cost of black

annealed 16 to 18 BWG M.S. Wire etc.

complete with all lead and lift.

7 Back filling with selected earth brought 4461.13 Cum 132.000

from out side borrow area ,or from

excavated useful material including

watering ramming, consolidation with

pneumatic temping and all lead and lift

8 Providing and fixing rolling shutters of 5.00 Sqm 3503.400

approved make made of 80mm wide MS

Laths inter locked together through

their entire length and jointed together

at the ends by end likes mounted on

specially designed pipe shaft with

bracket plates, guide channels and

arrangements for inside and outside

locking with push pull operation

complete including the cost of hood

cover and spring etc. complete(Width

Rolling Shutter

9 Providing and fixing window having 5.82 Sqm 1713.690

extruded aluminum Colour anodized

section frame main outer size

horizontal two track member size

Kg/mt, vertical member of size

Kg/mt with sliding shutters of

horizontal member size 40mm x 18mm

x1.29mm @ wt. of 0.456Kg/mt, vertical

member of size40mm x 18mm x

Wt.0.457 Kg/mt with 5 mm thick

transparent bronze colour tinted float

glass with powder coated aluminum

fittings and fixtures and transparent

silicon sealant glass fixing to frame as

per details etc complete for window.

10 Providing and laying brick masonry 25.43 Cum 5237.000

using std. modular brunt bricks (2nd

class) and cement mortar by mass incl.

striking out joints, curing, finishing and

scaffolding etc. complete. a) IN C.M. 1:5

For all lead and lift.

11 Cement plaster 20mm thick in single 1594.63 Sqm 248.000

coat to stone masonry in C.M. 1:3 incl.

finishing, curing, scaffolding etc

complete. a) UPTO 6.0 Mt HEIGHT

12 Cement plaster 15mm thick in single 151.90 Sqm 206.000

coat to brick masonry in C.M. 1:3 incl.

finishing, curing, scaffolding etc

a) UPTO 6.0 Mt HEIGHT (Inside Plaster)

13 Providing & laying cement concrete 44.15 Sqm 322.920

flooring 1:2:4 (1cement : 2 coarse sand :

4 graded stone aggregate 20 mm

nominal size) laid in one layer finished

with a floating coat of neat cement.

14 Providing and laying polished kota 44.15 Sqm 1056.250

stone slab 25 mm thick in risers of steps,

dado and pillars laid on 10 mm thick

cement mortar 1 : 3 (1 cement : 3 course

sand) and jointed with grey cement

slurry including rubbing and polishing

15 White washing with lime on wall surface 151.90 Sqm 12.080

(two coats) to give an even shade

including thoroughly booming the

surface to remove all dirt, dust; mortar

drops and other foreign matter.

16 Finishing wall with water proofing 928.46 Sqm 57.430

cement paint of on wall surfaces (Two

coats) to give an approved brand and

manufacture and of required shape even

shade after thoroughly brushing the

surface to remove all dirt and remains of

loose powered materials.

17 Providing and fixing G.I. Pipe railing ( B- 16.00 Rmt 1921.000

class medium duty ) as per design of

mt. height, using 75x75x10 mm size M.S

Angle at 2.0 mt c/c for vertical posts and

38 mm dia G.I. Pipe for 4 horizontal rows

incl. one coat of red oxide primer & two

coats of oil paint etc complete.

18 Heavy Duty Exhaust Fan 2.00 No 5000.000

19 Providing and fixing in position Cast 5.00 Kg 958.160

Iron Manhole Covers and frame

conforming to IS 1726. All exposed

edges rounded end finished in cement

mortar etc. complete.

20 Providing formwork of ordinary timber 1078.54 sqmt 389.730

planking so as to give a rough finish

including centering shuttering strutting

and propping etc. height of propping

and centering below supporting floor to

ceiling not exceeding 4 M. and removal

of the same for in situ reinforced

concrete and plain concrete work in. (G)

Columns Pillars, Posts and struts.

(2)Circular or curved in Plan.

21 Providing and fixing metal expansion 5.00 Rmt 2013.950

joints as per drawings. Details of

expansion joint 50 x 50 x 6mm size two

IS and 100 x 6mm MS plate with 6 x 20 x

25mm long hold fast @ 50 cm / cc on

both sides of expansion joints.

22 Providing formwork of ordinary timber 1006.53 sqmt 174.980

planking so as to give a rough finish

including centering shuttering strutting

and propping etc. height of propping

and centering below supporting floor to

ceiling not exceeding 4 M. and removal

of the same for in situ reinforced

concrete and plain concrete work in (G)

Columns Pillars, Posts and struts.

(2)Circular or curved in Plan.

23 Providing and laying uncoursed rubble 198.11 Cum 2621.000

masonry in cement and sand mortar by

mass and machine mixing incl. use of

header and bond stones etc and incl.

scaffolding and finishing to required

shape and batter end steps etc as per

drawing and racking out the joints,

curing etc complete in all respect. For all

lead lift. A) In C.M. 1:5 for foundation

and super structure.

24 SUBMERSIBLE PUMP:- 2.00 No. 1188257.0

Supply, installation, testing &

commissioning of sewage submersible,

non clog type suitable for working on

three phase, 50 Hz ± 3%, 415 V ± 10%,

AC supply, 1450 RPM synchronous

speed with 3 core flat copper cable from

pump to starter panel with cable end

terminations, all supports, clamps, pipe

fittings along with mechanical seal,

bearing bush, strainer etc. complete set

& following M.O.C: Casing: CI, Impeller:

SS CF8M, Wearing ring & Bearing bush:

Bronze, TC mechanical seal, CS / SS

bearing, SS shaft with sleeve, SS strainer

& MS motor body. (14) 95 Hp

25 Providing, Supplying, Lowering, Laying 2.00 No. 10555.000

and jointing ISI mark CI D/F Sluice valve

as per IS: 14846 (Latest Edition) of

following class and diameter including

all taxes, insurance, transportation,

freight charges, octroi, inspection

charges, loading, unloading, cost of all

labour, jointing material, including nut

bolts and giving satisfactory hydraulic

testing, conveyance to departmental

stores etc complete. PN-1 With hand w

heel/cap operated {PO type short body).

26 Providing, Supplying, Lowering, Laying 2.00 No. 16671.000

and jointing ISI mark CI D/F Reflux valve

as per IS: 15:531 2 (Latest Edition) of

following class and diameter including

all taxes, insurance, transportation,

freight charges, octroi, inspection

charges, loading, unloading, cost of all

labour, jointing material including nut

bolts and giving satisfactory hydraulic

testing, conveyance to departmental

stores etc complete. PN-1 With hand w

heel/cap operated {PO type short body).

27 Providing, Supplying, Lowering, Laying 1.00 No. 17945.000

and jointing ISI mark CI 0/F Butterfly

valve as per IS: 15:13095 (Latest

Edition) of following class and diameter

including all taxes, insurance,

transportation, freight charges, octroi,

inspection charges, loading, unloading,

cost of all labour, jointing material

including nut bolts and giving

satisfactory hydraulic testing,

conveyance to departmental stores etc

complete. Size: 300 mm NB (on header)

28 Providing, Supplying, Lowering, Laying 1.00 No. 11026.000

and jointing C.I Air valves of approved

make & quality of following class and

diameter including all taxes, insurance,

transportation, freight charges, octroi,

inspection charges, loading, unloading,

cost of all labour, jointing material

including nut bolts and giving

satisfactory hydraulic testing,

conveyance to departmental stores etc

complete. Size: 100 mm

29 EXPANSION BELLOWS:

Supply, installation, testing &

commissioning of flange ends Expansion

Bellow as per EJMA standards of overall

length of minimum 300 mm, designed

for 15 mm axial compression and 5 mm

axial extension with tie rods etc. of

following MOC & pressure ratings.

MOC: Bellows: SA 240 Gr. 304; Internal

Sleeve: SA 240 Gr. 304; Weldends: IS

2062 Gr. B; Flanges: IS 2062 Gr. B

(Drilling as per IS 1538 / IS 6392 ) &

Limit Rods & Nuts: CS - IS

(a) Size: 200 mm NB- on delivery side 2.00 No. 6216.000

(b) Size: 300 mm NB- on delivery side 1.00 No. 10200.000

30 Manufacture. Supply, Delivery of 30.00 Mtr. 2891.000

Lowering, laying, Jointing & welding in

position to correct line & level M.S. Pipe

with outer gunniting & inside

lining/Epoxy painting on pedestal or

chairs upon prepared formation or

prepared bedding in trenches the rates

include conveyance from store to site of

work loading, unloading, joint

plastering, hydrotesting of Electric

Resistance Welded (Up to

400mm)/Submerged Arc

Welded(Above 400mm) M.S. Pipe

having beveled ends plate or coil

conforming to IS-3589-2001 or its latest

revision/ ammendment for following

thickness outside diameter at GWSSB

store or sile anywhere in Gujarat State

including all taxes. insurance,

transportation, freight charges, octroi,

inspection charges, loading, unloading

conveyance to Departmental stores,

stacking etc. all complete. (Rate for MS

Pipe based on the ex. works price of HR

Coil as Rs.58500.00 per MT- without

GST (Above 3.15 mm to 10 mm) & Rs.

59000.00 per MT without GST (Above

10 mm) as on Jan-23.( WPI Index of H. R

Coi! of Dec-22 is 144) etc. complete.

Size: 200 mm NB-6.3 mm thick (on

Delivery side)-As per site requirement

31 BLIND FLANGES: 2.00 No. 990.000

Providing and laying in position

including testing following all flanged

cast iron blank flanges (200 mm Dia)

32 PRESSURE GAUGE: 2.00 No. 1029.000

Design, Supply, Installation, Testing,

Commissioning of Bourdon Type

Pressure Gauge, ±1% accuracy, Direct

bottom 1/2" NPT (M) process

connection, IP 67, Glycerine filled, SS304

Case with Bayonet Type Bezel, SS316 L

Bourdon Tube, SS 316 Movement

material, Aluminium dial with black

graduation on white background, Micro

Zero adjustable pointer, neoprene

gasket, Blow out disc, shatter proof

glass, SS tag plate etc as per IS

Range : 0 - 6 kg / sq.cm.

33 FLOW METER: 1.00 No. 210688.00

Design, Supply, Installation, Testing,

Commissioning of Full Bore

Electromagnetic flow meter with factory

calibration, Inbuilt Battery Power

Operated, flanged connection, Flow

sensor, Indicator, transmitter and

totaliser with all accessories viz. surge

arrestor, associated cables, cabinets,

hardwares, etc complete as per

following specifications:

Flow Meter/ Sensor:

DC pulsed type, IP 68 Protection,

Flanged process connection as per IS

1538 or equivalent standard, SS304/

Metallic Alloy Flow Tube, SS316/ SS

L/ Hastelloy Sensor, SS316/ Hastelloy

Grounding Ring/ Inbuilt Grounding

Electrode, Neoprene/Polyurethane/

Hard Rubber/ Rilsan lining, SS304/ Die

Cast Aluminium/ Carbon steel with

Anticorrosive Paint Coil Housing with

Junction Box, CS flanges.

Flow Transmitter/ Converter ( Remote

Field Mounted):

Microprocessor based, Modular design,

2 line LCD for indication of actual flow

rate, forward, reverse, sum totaliser

display, ±0.5% accuracy at 0.3 to

m/sec velocity, one scalable pulse/ one

status, one Modbus output, one GPRS/

GSM output, IP 67 protection, Die cast

aluminium/ polycarbonate/ SS316 with

Anticorrosive Paint/ PU finish with glass

window enclosure, Inbuilt EEPROM and

Data Logger, 20 meters cable length for

sensor to transmitter communication,

Minimum 5 years battery lifetime,

Rechargeable Lithium-thionyl chloride/

Ni-Cd high power batteries, Hourly

Basis Worldwide transmission of

measured data and events via e‐mail

and SMS by integrated GSM/GPRS

modem, Reliable data storage facility

through integrated SD card etc along

with wall mounted/ stand mounted

Meter Size : 300 mm

34 EOT Crane (Circular):- 1.00 No. 428250.00

Supply, installation, testing &

commissioning single girder type fully

electrically operated EOT crane with

electrically operated hoist, class II duty,

geared travelling trolley with seven

meter lift complete with long travel rail

track (40 mm sq. bar), moving or cross

girder, all three motions electrically

operated by suitable rating motor IP

control panel & down pendant control

block, brake, safety device, cables form

motor to starter panel & other required

accessories & tested as per IS

Specifications.

35 MISCELLANEOUS: 100.00 Kg 85.000

Providing, S.I.T.C of Structure Steel at

site of work with freight, loading,

unloading carting, etc. including all taxes

and duties complete such as joints,

channels, angles, Iron Rails,

ISA/ISMC/ISMB/MS flat, Plates,

Chequered plates (below 10mm

thickness) etc. required for support

structure of Electro- Mechanical

equipment etc. for support on floor /

wall / beam / brackets etc. as per tender

36 Manufacture. Supply & Delivery of 25.00 Mtr. 4904.000

Electric Resistance Welded (Up to

400mm)/Submerged Arc

Welded(Above 400mm) M.S. Pipe

having bevelled ends plate or coil

conforming to IS-3589-2001 or its latest

revision/ amendment for following

thickness outside diameter at GWSSB

store or sile anywhere in Gujarat State

including all taxes. insurance,

transportation, freight charges, octroi,

inspection charges, loading, unloading

conveyance to Departmental stores,

stacking etc. all complete. (Rate for MS

Pipe based on the ex. works price of HR

Coil as Rs.58500.00 per MT- without

GST (Above 3.15 mm to 10 mm) & Rs.

59000.00 per MT without GST (Above

10 mm) as on Jan-23.( WPI Index of H. R

Coi! of Dec-22 is 144)

Cast Iron Wall Thimble Mounted Sluice

Gate as per IS: 13349 Standard, Size:

(W) x 700 (H) mm, Suitable for upto

m seating as well as unseating Operating

water head, 11 m CL-PL distance,

Manually operated with indicating

arrangement, Rising spindle, Flush

bottom closure arrangement, Upward

Opening, Open top flange back frame

gate. (Design Head Class-II type)

Electrical Work

38 LT PMCC With APFC Panel: 1.00 Nos. 610500.00

Design, engineering, procurement,

installation, testing and commissioning

of PMCC panel with totally enclosed type

as per IS: 2147 & IS-8623, operation on

three phase,415V, 50Hz,neutral

effectively grounded, IP 52, with

instrument compartments indicating

lamps, control contactors as per IS:

13947,relays and control fuses air

insulated . Incoming & Outgoing feeder

details shall be as per Design & SLD

Drawing. ACB/ MCCB as incomer feeder

, outgoing feeder with S/D , Soft starter,

VFD,DOL feeder & TPN MCCB/SFU etc as

per Design & SLD Drawing.

39 1.1 kV Grade Cable- Aluminium / Copper

Supply, laying, testing & commissioning

1.1 kV grade, XLPE insulated, stranded

Al/CU conductor, galvanised steel flat

strip / round wire armoured, extruded

PVC type ST2 sheathed, heavy duty

cable (to be laid on wall surface with

necessary clamps / in existing cable

trench / cable trays / conduit / pipe

sleeves at road crossing or floor as per

site requirement) conforming to

IS:7098 (Part-1) & IEC:60502

(Part-1) of following sizes:

(a) 1.1kV,4Cx2.5 Sq. mm ,Cu 80.00 mtr 81.000

(c) 1.1kV,3Cx2.5 Sq. mm ,Cu 80.00 mtr 86.000

40 Double Compression Brass Cable

Glands: Providing & fitting heavy duty

brass cable glands (nickel-plated) with

washers & rubber ring conforming to IS,

suitable for 3, 3½ & 4 core cables of

following type & sizes:

(a) 3 Sq mm, 2 to 4 Core 4.00 Nos 73.000

(b) 185 Sq mm, 3 to 3½ Core 1.00 Nos 522.000

41 Cable Trays & Accessories

Supply & laying GI ladder type cable

trays with side channels of size - 75 x

x 15 mm / 100 x 15 x 15 mm & rungs of

size - 35 x15 x 15 mm spaced at 250 mm

apart, fabricated from 2 mm thick sheet

steel in standard length of 2.5 meter,

duly hot dipped galvanized after

fabrication as per IS 2629-1989/ IS

4759-1984 including accessories such

as coupler plates/ fish plates, bends,

tees, reducers, elbows, covers and

electro-galvanized hardware etc,

erected on existing support as per

specification and instruction of

Engineer-in-charge.

42 Earthing & Lightning Protection System:

Providing EARTHING & Lighting

protection for Pump house, Electrical

panel room, Out side Pump house area &

Switchyard area equipments including

Earthing pits, Electrode, GI Strips, MS

Strip as per IS 3043 & IEEE 80 & tender

specifications.

(a) Providing and erecting Pipe type 8.00 Nos 815.000

earthing with 40 mm dia. 2.5 mtr long 'B'

grade G.I. pipe with necessary coupling

buch buried in specially prepared earth

pit & G.I. earth wire of 8 SWG erected &

connected as directed (For panel)

(b) For using salt and charcoal / coke as 16.00 Nos 170.000

required for pipe type earthing.

(c) Supplying & erecting funnel type 4.00 Nos 7797.000

earthing having earth plate of following

size burred in specifically prepared

earth pit 3 mtr. below ground with

kg. charcoal and salt with alternate

layers of charcoal & salt, 20mm.dia. G.I.

pipe with Funnel with a wire mesh for

watering & bricks masonry block, C.I.

Cover complete as per para 7.3 of IS

3043 with necessary length of double

Galvanised Iron / copper earth wire No

6 SWG bolted with lug to the plate and

covered in 12 mm dia. G.I. pipe 2.5 mtr

long complete connected to the nearest

switch gear with end socket as per

direction & duly tested by earth tester

confirming to IS (As per drawing) with

following specification

(C) with 60 x 60x 0.315 cms. Copper

(d) Providing and erecting HOT deep 150.00 Kg 77.000

Galvanised iron strip wire 8 to 16 SWG.

(e) Providing and erecting required size 60.00 Kg 787.000

Copper strip for earthing of H.T. OCB /

ACB/ Transformer, LT panel board,

Motors etc. using copper clamp.

43 Lighting-Indoor & Outdoor

(a) Point wiring for Light / Fan/ Bell/ 12.00 Pt 326.000

Primary Point with 2-1.5 sq. mm &

earth wire of 1.5 sq. mm (green) both

are of ISI marked 1.1 kv grade FRLS

PVC insulated multi strand copper wires

upto max length of 10 mt, in below type

of pipe erected with 6A Tissino Type ISI

marked flush type switch / bell push and

accessories erected on Metal /

PVC/Wooden Box covered with 3 mm

thick PC(Polycarbonate)

/Acrylic/Laminated sheet. with

necessary Lamp holder/ceiling rose /

H.D. Connector as directed.

(a) with medium class Rigid PVC pipe

and accessories erected flushed on

wall/ceiling complete

(b) Point wiring for independent PLUG with 4.00 Pt 460.000

following size mains earth wire of

sq.mm (green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multi

strand copper wires upto 10 mt length,

in following below of pipe erected

complete with ISI marked 3 / 5 Pin

socket and tissino type switch erected

with earth continuity connection

erected on Metal / PVC/Wooden box

covered with 3 mm thick

PC(Polycarbonate) / Acrylic

/Laminated sheet.

[B] 6/16A Plug and 16 amp switch with

2-2.5 sq. mm Cu. Mains from mcb d b

(a) with medium class Rigid PVC pipe

and accessories erected flushed on

wall/ceiling complete

(c) Supplying and erecting LED indoor 6.00 Nos 530.000

fittings with LEDs of wattage 0.2 Watt to

0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be

made of thick sheet Steel conforming to

IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. &

corrosion resistance with diffuser with

company mark/name 160V to 270V,

Power Factor more than 0.95, THD <

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description

have shown ranges of Wattage capacity

of LED fittings. The Engineer in charge

may select any wattage capacity

between the ranges shown.)

(A) Tube Light with integral driver

(v) 36-40 Watts, Surge-2 KV, IP-20,

conventional 4 feet(Cat III)

(d) Supplying and erecting LED street light 4.00 Nos 2180.000

/ Flood light fittings with High power

White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency

more than 130 lm/w and corrosion free

High pressure die cast aluminium

housing with smooth finish powder

coated and heat sink extruded

aluminium with diffuser and

Polycarbonate optics/ lenses with

company mark/name engraved or

embossed 160 to 270 V, Power Factor

more than 0.95, THD < 10 %, CCT

K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt .

LED driver efficiency > 85 %.( fittings

required LM-79 & LM-80

certificates)(NOTE: Below description

have shown ranges of Wattage capacity

of LED fittings. The Engineer in charge

may select any wattage capacity

between the ranges shown.) (A) Street

Light (IP-65), Surge protection -4KV

integral and ,Light must have 440VAC

line supply with over-voltage

(iii) above 24 to 36 watts(Cat-lll)

(e ) Supplying & erecting Steel tubular pole

(Swaged) confirming to IS - 2713 (Part-

II) 1980. Manufacturing process of steel

tubular pole should be as per IS

specification. Basic steel tube should be

ISI Marked. Pole should be painted by

one coat of Zinc comet Primer and two

coat of Aluminium /approved paint to

be erected on / in existing Foundation.

The length of poles are as below.

(A) 7.5 mtr. Long Swaged Steel tubular

(i) pole as per IS code 410-SP-4 with 4.00 Nos 7175.000

300 X 300 X 4 mm base plate with

necessary G.I. J Bolts (Approximate Pole

weight 67 Kg) For burial erection

(f) Providing & erecting Approved make 2.00 Nos 2289.000

Ceiling Fan with double ball bearing ISI

mark with Condenser 230 volt A.C.50 Hz

1200 mm sweep complete having

blades aluminium body and blade sets

having ornamental design shanks

canopy erected with earthing. [ Make

shall be approved by Engineer in

(g) Supplying & erecting single phase 6.00 Nos 3306.000

approved make industrial exhaust fan

suitable for medium duty ring mounted

low noise operation suitable for medium

duty having following dia size and

maximum speed in RPM

[D] 450 mm dia 900 RPM (Cat-lll)

45 SAFETY ACCESSORIES

(a) Providing and fixing printed instruction 2.00 NOS 129.000

chart both in English and Gujarati and

duly framed with front glasses, for

treatment of person suffering from

Electric shock with minimum 50"

diagonally size.

(b) Providing pair of rubber hand gloves 2.00 SET 212.000

suitable for working on 11 KV/22 KV

(c) Supplying rubber matting of following 12.00 SQ.M 3051.000

12 mm thickness as per IS:15652/IEC TR

(d) Supplying stand first AID box with 3.00 NO 297.000

antiseptic cream, medicine for use on

wounds due burn, crepe bandage, gauge

bandage, medicated ready to use

bandage (Band-aid) adhesive tape for

medicinal user, Scissors, anti-septic

solution (Savlon or similar) etc. (All

above contents shall be of standard

(e) Supplying FIRE bucket round bottom of 3.00 NOS 212.000

9 litres capacity made out of 24 gauge

G.I. sheet with extra handle at bottom

duly painted white inside and Red out

side with FIRE mark, filled with dry-

sand and kept on existing stand

provided or hung on wall hook.

(f) Supplying & erecting carbon dioxide 1.00 NOS 8586.000

(CO2) fire extinguisher user of following

capacity with necessary clamps made

from 50 x 6 mm M.S. Flat with nut &

bolts grouted in wall complete.[B] For

5.5 / 6.5 KG Capacity

Instrumentation

45 Pressure Gauges with Accessories

Design, Supply, Installation, Testing,

Commissioning of Diaphragm sealed

Pressure Gauge, ±1% accuracy, Direct

bottom 1/2" NPT (M) process

connection, IP 67, Glycerine filled, SS304

Case with Bayonet Type Bezel, SS316 L

Diaphragm, SS316 Bottom Housing

Material, SS 316 Movement material,

Aluminium dial with black graduation

on white background, Micro Zero

adjustable pointer, neoprene gasket,

Blow out disc, shatter proof glass, SS tag

plate etc as per IS

0 to 6 Kg/cm2 (150 mm Dial Size) 2.00 Nos 3012.000

46 Full Bore Electromagnetic Flow Meter-

Regular Power operated

Design, Supply, Installation, Testing,

Commissioning of Full Bore

Electromagnetic flow meter with factory

calibrated, Regular Power Operated,

flanged connection, Flow sensor,

Indicator, transmitter and totaliser with

all accessories viz. surge arrestor,

associated cables, cabinets, hardwares,

etc complete as per following

specifications: Flow Meter/ Sensor: DC

pulsed type, IP 68 Protection, Flanged

process connection as per IS 1538 or

equivalent standard, SS304/ Metallic

Alloy Flow Tube, SS316/ SS 316 L/

Hastelloy Sensor, SS316/ Hastelloy

Grounding Ring/ Inbuilt Grounding

Electrode, Neoprene/ Polyurethane/

Hard Rubber/ Rilsan lining, SS304/ Die

Cast Aluminium/ Carbon steel with

Anticorrosive Paint Coil Housing with

Junction Box, CS flanges. Flow

Transmitter/ Converter ( Remote Field

Mounted):Microprocessor based,

Modular design, 2 line LCD for

indication of actual flow rate, forward,

reverse, sum totaliser display, ±0.5%

accuracy at 0.3 to 4 m/sec velocity, 4 to

20 mA with HART/Modbus output, one

scalable pulse, one status output, IP

protection, Die cast aluminium/

polycarbonate/ SS316 with

Anticorrosive Paint/ PU finish with glass

window enclosure, Inbuilt EEPROM and

Data Logger, 20 meters cable length for

sensor to transmitter communication

etc along with wall mounted/ stand

mounted cabinet.

(a) 300mm Nominal Bore ( For Pump House 4.00 Nos 134422.00

and Chak-2, 3, 4)

(b) 250mm Nominal Bore ( For Chak-1) 1.00 Nos 117201.00

47 Ultrasonic Level Transmitter

Ultrasonic Type Level Transmitter with

Remote Display :Design, Supply,

Installation, Testing and Commissioning

of NOn Contact Ultrasonic Type Level

Transmitter with Remote Display.

Sensor: The sensor should be non

contact type, field mounting type,

housing shall have minimum IP65

protection, PP/ PVC Sensor MOC, with

sensor to transmitter cable. Remote

Indicator cum Transmitter: Micro

processor based indicator with LED /

LCD digital display, panel/ wall

mounting type, power supply shall be

110-240 Vac or 15 to 36 Vdc, 50 Hz ±

%.Accessories: Mounting bracket, nut,

bolts etc as per system requirement and

Hook up diagram of the Instruments.

Level Transmitter shall be suitable for

following Range.

0 to 10 Meter 1.00 Nos 59436.000

48 PLC HMI Panel

Design, manufacture, supply, 1.00 Nos. 715000.00

installation, testing and commissioning

of indoor type PLC panel with 10" HMI

and necessary hardware, fabricated out

of min. 2 mm thick CRCA sheet complete

with latest configuration PC, necessary

programming for SCADA software and

comprising of all accessories. The I/O's

with minimum of 20% spare with

respect to the specification as directed

49 Cable and accessories:-Supply, laying,

testing & commissioning Overall

Shielded Armoured Cable, stranded CU

conductor with all accessories as

directed by Officer.

(a) 1 PAIR X 1.5 SQ MM CU 30.00 Mtr 211.200

(b) 2 PAIR X 1.5 SQ MM CU 40.00 Mtr 342.100

(c) 4 PAIR X 1.5 SQ MM CU 40.00 Mtr 574.200

Rising Main ( DI K-9) & Distribution

50 Providing and supplying D. I. K-9 grade

pipes for following nominal bore

diameter with internal cement mortar

lining including all taxes, insurance,

transportation, freight charges, octroi,

inspection charges, loading, unloading,

conveyance to departmental stores,

stacking etc. complete. (IS 8329-2000).

Rate for DI pipe based on Wholesale

Price index of Pig Iron as 157.60 for the

month of Dec-2022.

(a) 250 mm Dia. Pipe 338.00 Rmt. 2998.000

(b) 300 mm Dia. Pipe 1976.00 Rmt. 3788.000

51 Manufacture, Supply & Delivery of

Ductile Iron Flange socket spigot bends,

tees, reducers or any other specials as

per BS-EN-545/1995 Class-A series K12

suitable for use with D.I. Pipes

manufactured as per

IS:8329/1994delivery of specials is to

be made to GWSSB store or site of works

any where in Gujarat including all taxes,

loading, unloading, carting, stacking,

insurance, inspection charges, octroi etc.

Rate for Specials 80 to 300mm dia 1149.00 KG 148.000

52 Providing and supplying ISI mark CI D/F

Sluice Valves as per IS:14846 (Latest

Edition) of following class and diameter

including all taxes, insurance,

transportation, freight charges, octroi,

inspection charges, loading, unloading,

conveyance to departmental stores,

stacking etc. complete.

A9) P.N.1.6 with hand wheel/cap

operated (PD type short body)

(a) 250mm dia @ 1-CMS2 to CMS1 1.00 Nos. 16402.000

(b) 300mm dia @ 1-CMS4 to CMS3 & 1- 2.00 Nos. 20946.000

53 Supply, testing & commissioning of

flange ends Expansion Bellow as per

EJMA standards of overall length of

minimum 300 mm, designed for 15 mm

axial compression and 5 mm axial

extension with tie rods etc. of following

MOC & pressure ratings.

MOC: Bellows: SA 240 Gr. 304; Internal

Sleeve: SA 240 Gr. 304; Weldends: IS

2062 Gr. B; Flanges: IS 2062 Gr. B

(Drilling as per IS 1538 /IS 6392 ) &

Limit Rods & Nuts: CS - IS 1367. (P.N 1.6)

54 Providing and supplying C. I Air valves 6.00 Nos. 3660.000

of approved make & quality of following

class and diameter including all taxes,

insurance, transportation, freight

charges, octroi, inspection charges,

loading, unloading, conveyance to

departmental stores, stacking etc.

air valve Double Acting (DS2) type

80mm dia @ 500m interval

55 Providing and supplying ISI mark G. I. 18.00 Rmt 598.000

pipes with Couplings of following class

and diameter including all taxes,

insurance, transportation, freight

charges, octroi, inspection charges,

loading, unloading, conveyance to

departmental stores, stacking etc.

complete. (IS -1239) (Not for well/tube

well column pipe)

80mm dia GI pipe (Medium Duty)

56 Excavation for pipe line trenches for

water supply, sewerage line, manhole

etc. all with shoring and struting if

required as per required gradient and

line including safety provisions using

site rails and stacking excavated stuff

including up to all required lead

cleaning the site etc. complete for all lifts

and strata as specified.

0.0 to 1.5 mt depth.

a) In all sorts of soil, soft murrum and 5040.61 Cum 89.000

b) In hard murrum, boulders incl. 894.27 Cum 135.000

c) In soft rock and/or masonary in CM or 894.27 Cum 163.000

LM or Lime Concrete.

57 Lowering, laying and jointing C. I. S & S

Spun pipes suitable for Tyton joints /

Mortar lined D. I. Pipes of various classes

with CI / MS specials of following

diameters in proper position, grade and

alignment as directed by Engineer-in-

charge including hydraulic testing etc.

(a) 250 mm Dia. Pipe 338.00 Rmt. 127.000

(b) 300 mm Dia. Pipe 1976.00 Rmt. 155.000

58 Lowering, laying and jointing in position

following C. I. / D/F Reflux valves,

Butterfly valves, Sluice valves including

cost of all labour, jointing material,

including nut bolts and giving

satisfactory hydraulic testing, etc.

complete.A9) P.N.1.6 with hand

wheel/cap operated (PD type short

(b) 250mm dia @ 1-CMS2 to CMS1 1.00 Nos. 946.000

(c) 300mm dia @ 1-CMS4 to CMS3 & 1- 2.00 Nos. 1141.000

59 Lowering, laying and jointing in position

following C. I. / D/F Air valves including

cost of all labour, jointing material,

including nut bolts and giving

satisfactory hydraulic testing, etc.

(b) 80mm dia @ 500m interval 6.00 Nos. 411.000

60 Lowering, laying and jointing G. I. pipes 18.00 Rmt 27.000

with G. I. specials of following diameters

in proper position, grade and alignment

as directed by Engineer-in-charge

including conveyance from stores to site

of work, labour, giving hydraulic testing,

etc. complete, 40 mm. dia. G.I. Pipe

80mm dia GI pipe (Medium Duty)

61 Construction of valves chambers in

brick or bela stone masonry, locally

available in C. M. 1:6. Foundation

concrete 150 mm thick in C. C. 1:4:8 of

trap metal size 25 mm to 40 mm thick,

inside cement plaster in C. M. 1:3 and

cement pointing outside in C. M. 1:3 and

top cover of precast RCC slab 100 mm

thick (with key hole in two parts, each

with handles or MS Bar etc. complete as

given size) Upto 1 Mt. depth from G. L. to

pipe invert level incl. complete civil

works but excl. cost of excavation and

refilling, with cast in situ RCC slab in one

single piece with fixing of CI-MH Frame

and cover (excl. cost of CI-MH Frame and

cover) with 23 mm thick brick masonry

wall in C.M.1:6

(a) Valve chamber of Size 0.9 x 0.9 x 1.0 m 61.00 Nos. 7738.000

size for Air Valve

(b) For 1 mt extra Depth 9.00 Rmt. 4479.000

62 Providing and casting in situ C. C. in 64.00 Cum 6722.000

grade M-20 (proportions as per mix

design or as per table 9 of IS 456 -

in masses by weigh batching) usng

granite, quartzite trap metal of size

mm to 20 mm for RCC work, including

scaffolding centring, form work, needle

vibrated consolidation, curing complete

up to 6 M depth or height (excluding cost

of reinforcement and neat finishing)

wiht centring and shuttering etc.

complete for structure other than water

retaining.Thrust Block & Air valve Riser

63 Providing, cutting, bending, binding and 2.828 MT 76303.000

fixing in position as per drawing .TMT

BAR , reinforcement for R.C.C. works

and anchor bars incl cost of black

annealed 16 to 18 BWG M.S.. Wire etc.

complete with all lead and lift. (b) Fe-

64 Providing bedding incl. ramming, 205.72 Cum 176.000

watering, levelling, consolidating etc.

Complete as per standard and

instruction of engineer in charge.

As above with Murrum brought from

outside including all lead

65 Refilling the pipeline trenches incl. 6292.18 Cum 22.00

ramming, watering, consolidating

disposal of surplus stuff as directed

within a radius of 3 km.

66 Providing C.C.M.:100 for encasing pipes 44.36 Cum 4113.800

using trap metal size 12 mm to 50 mm

incl. form work curing consolidation etc.

complete for various location on pipe

line Using Trap Metal 20mm nominal

67 Providing and supplying ISI mark CI D/F 52.00 Nos. 5866.000

Butterfly valve as per IS:13095 (Latest

edition) of following class and diameter

including all taxes, insurance,

transportation, freight charges, octroi,

inspection charges, loading, unloading,

conveyance to departmental stores,

stacking etc. complete.

68 Providing and supplying in standard

lengths ISI mark high density

Polyethylene H.D.P.E. Pipes suitable for

potable water, as per IS specifications

no. 4984/1995 including all local and

central taxes, transportation, freight

charges, octroi, inspection charges,

loading, unloading, conveyance to the

departmental stores, and including cost

of jointing material etc, complete.

H.D.P.E. PE-100, Pipe 6.0 kg/cm²

69 Lowering, laying, fixing and jointing

HDPE pipes and specials of all class and

following diameter (By butt fusion

welding method) including cost of

conveyance from stores to site of works

including cost of labour, material, giving

satisfactory hydraulic testing as per ISI

code etc, complete.

70 Providing and supplying CI Double 12.00 Nos. 2496.000

acting Air valve of approved make and

quality of following class and diameter

including all taxes, insurance,

transportation, freight charges, octroi,

inspection charges, loading, unloading,

conveyance to departmental stores,

stacking etc. complete.

71 Providing & Laying in position 0.43 Cum 2997.000

controlled cement concrete using

cement sand & crushed metal aggregate

by machine mix incl. necessary

formworks ,compaction by mechanical

vibrator curing as directed with all lead

and lift etc complete. Excluding the cost

of steel . For foundation concrete.

P.C.C. in foundation for Air Valve

72 Prov. and Laying in position Controlled

cement concrete using cement, sand and

crushed aggregate by mass and machine

mix for R.C.C/CC work including

necessary formworks centering

scaffolding compaction by mechanical

vibrator, curing as directed with all lead

& lift etc complete Excluding the cost of

reinforcement. FOR COLUMN AND

BEAMS. C) Concrete grade M-20 and

(a) R.C.C. in footing for Air Valve structure 1.68 Cum 5006.000

(b) R.C.C. in column for Air Valve structure 1.17 Cum 5006.000

73 Providing and supplying ISI mark G.I. 30.00 Rmt 369.000

Pipes with flanged ends of medium duty

and following diameter including all

taxes, insurance, transportation, freight

charges, octroi, inspection charges,

loading, unloading, conveyance to

departmental store, stacking etc,

complete. (IS:1239)

50 mm for Air valve

74 Estimate for construction of Cross- 1.00 Lum 558268.95

drainage works in command area, like p

road crossing, nala crossing, railway sum

crossing, river crossing, excluding land

75 Operation and maintenance for below 10.00 Per 495515.15

years of entire scheme including all year

types of repairs in entire scheme

including field and pump house

components, all types of daily

operations required for successful

commissioning of entire scheme. Hence,

no provision for materials, spares, oil

and lubricants and other materials

required for maintenance.

I/We am/are willing to carry out the work at… % above/below percent (Should

be written in figures and words) of the estimated rate mentioned above. Amount of my /our tender

works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

For Item Rate Tender (For above INR 50 Cr.):

Item No Description of Item (with brief Quantity Unit Rate Amount

specification and reference to

book of specifications) In figures In Words

(A) Total Tendered Amount

(B) Rebate on above tendered amount (if any) % (in figure) ………………………………

(C)Net Tendered Amount (A-B) (in figure) ………………………………

1 The Contractor shall exhibit a board with brief details of work as directed by the

Engineer-In-Charge for which no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 GST and Income tax TDS will be deducted at a source while making payments of bills

4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.

NO.: MIS102010/17/K1 Dated:30/07/2018 as stated in S.O.R. therefore in

R.C.C. items where there is a change as per actual mix design the cost of difference of

cement consumption have been deducted from the rate of original item at the rate of input rate

mentioned in all the tender.

Signature of Contractor Executive Engineer

Gir Somnath Irrigation Division