CONSTRUCTION OF PROPOSED 50 BEDDED MOTHER AND CHILD CARE HOSPITAL, HALDWANI DISTRICT - NAINITAL

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1%concentration

Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete : Serrated with central bulb (225 mm wide, 8-11 mm thick)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness),including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size).

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering,shuttering, finishing and reinforcement, including admixtures inrecommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works upto plinth level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering,shuttering, finishing and reinforcement, including admixtures inrecommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works above plinth level upto floor V level

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars

Centring and shuttering including strutting,ropping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Columns, Pillars, Piers, Abutments, Posts and Struts

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Suspended floors, roofs, landings, balconies and access platform

Shelves (Cast in situ)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate

12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand)

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. sqm

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Supply fixing & testing for Mechanical fasteners hilti 20 mm thickness.

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.: 0.63 mm thick with zinc coating not less than 275 gm/ m²

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade. 8mm thick (mirror polished and machine cut edge) Granite stone of any colour and shade

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. completeGranite of any colour and shade:Area of slab over 0.50 sqm

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar tapsetc. including moulding, rubbing and polishing of cut edges etc. complete.

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing inwhite cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : Gang saw cut stone 30mm thick Red sand stone

Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required.

Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases.

Extra for stone work for wall lining on exterior walls of height more than 10 m from ground level for every additional height of 3 m or part there of.

Providing and fixing G.I.swing Door Supply and installation ,Testing and Commissioning of FIRE RATED DOOR tested for 2 hours all included frame thicknes 100*58 mm, frame sheet thickness 1.2 mm with Rockwool infill, Door leaves sheet thickness 0.8mm skin pass galvanised iron sheet with honeycomb Kraft paper infill, leaf thickness 46mm, door stopper, door closer, Ball bearing butt hinge of size 102*75*3mm with SS screw, Mortise dead bolt lock with euro profile, door stopper, door closer, Fire rated clear glass 200*300*6mm, D handle both side 19*254 mm, double shutter, with 300 mm ventilator, including installation etc. complete in all aspects as per direction of Engineer in Charge. (Make- Tata Pravesh) D1 opening size 1800*2400 double leaf

D2 opening size 1500*2400 double leaf

D3 opening size 1200*2400 single leaf

D4 opening size 900*2400 single leaf

D5 opening size 750*2100 single leaf

D6 opening size 1200*2400 single leaf Fire door

D7 opening size 900*2100 single leaf

D8 opening size 1200*2400 single leaf

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete : 25 mm dia

Aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make, including tubular handle bar of 32 mm/ round shape handle of outer dia 100mm, hanging door stopper, hydraulic door closer, 12 mm thick prelaminated particle board conforming to IS:12826 grade,12mm thick toughened glass door shutter conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps atjunctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, including hinges, pivots all complete as per architectural drawings and the directions of Engineer-in-charge : Powder coated aluminium (minimum thickness of powder coating 50 micron) V1 opening size 1800*600, top hung and ventilator

V2 opening size 1500*600, top hung and ventilator

V3 opening size 1200*600, top hung and ventilator

V4 opening size 900*600, top hung

V5 opening size 750*600, Fixed

Aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make, including tubular handle bar of 32 mm/ round shape handle of outer dia 100mm, hanging door stopper, hydraulic door closer, 12 mm thick prelaminated particle board conforming to IS:12826 grade,12mm thick toughened glass door shutter conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps atjunctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, including hinges, pivots all complete as per architectural drawings and the directions of Engineer-in-charge : Powder coated aluminium (minimum thickness of powder coating 50 micron) W1 opening size 2400*1200, THREE TRACK WITH WIRE MESH SLIDER REFLECTOR TOUGHENED GLASS

W2 opening size 1800*1200, THREE TRACK WITH WIRE MESH SLIDER REFLECTOR TOUGHENED GLASS

W3 opening size 1200*1200, THREE TRACK WITH WIRE MESH SLIDER REFLECTOR TOUGHENED GLASS

W4 opening size 900*1200, CASEMENT OPENABLE VILLA WINDOW WITH REFLECTOR TOUGHENED GLASS

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Precast terrazo tiles 22 mm thick with graded marble chips of size upto 12 mm, laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement:4 coarse sand) : Light shade pigment using white cement

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

Providing and fixing Ist quality Thermatek Heat Resistant Tiles as Per Following Approved Specification, Supply of 300x300 mm Roof Tiles, Appearance White (Stone Punch Finish), Solar Reflective Index (SRI) 102 (ASTM E 1980)Reflctance 0.8121, Emissivity 0.8921, Materials used-Infrared Resistive Composition (NON Degradable), Tile Thickness - 10MM (±), Imprevious to Water, Stain Resistant, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

15 mm thick cement plaster in cement mortar 1:6 on Rough Side of brick wall including supply of all material , labour and T&P etc.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately): Flat surfaces

Providing fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS : 8183, density 24kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags, fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building.

Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 15 mm dia nominal bore

20 mm dia nominal bore

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

80 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.. External work 80 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 15 mm dia nominal bore

20 mm dia nominal bore

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

80 mm dia nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 50 mm nominal bore. Horizontal

80 mm nominal bore. Horizontal

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular tank

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge : 15 mm nominal dia

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approvedquality . (Jaquar) (15 mm nominal bore)

Providing and fixing C.P. brass angle cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore (Jaquar)

Supply and installation of Kirloskar make pump Type KDS 527++ (2HP) Three phase Suc X Del 80 X 65, Head 40 mtr Flow 18.3 Lps, MOC Impeller CI,Pump Casing CI complete in all aspects as per direction of Engineer In-charge

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 1500x450 mm

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing soil , waste and vent pipes: Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 100 mm dia

75 mm dia

Providind and fixing M.S.holder bat clamps of approved design to sand cast iron/cast iron (squn) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1cement :2coarse sand :4graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the walls etc: for 100 mm dia pipe

for 75 mm dia pipe

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 100 mm diameter pipe

75 mm diameter pipe

Providing and fixing 100 mm sand cast iron S&S plain bend of required degree. Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 100 mm diameter pipe

75 mm diameter pipe

Providing and fixing heel rest sanitary bend. 100 mm diameter pipe

75 mm diameter pipe

Providing and fixing double equal plain junction of required degree. Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 100x100x100x100 mm

75x75x75x75x75 mm

Providing and fixing single equal plain junction of required degree : Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 100x100x100 mm

Providing and fixing double unequal plain junction of required degree: Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 100x100x75x75 mm

Providing and fixing single unequal plain junction of required degree : Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 100x100x75 mm

Providing and fixing double equal plain invert branch of required degree: Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 100x100x100x100 mm

Providing and fixing single equal plain invert branch of required degree : Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 100x100x100 mm

Providing and fixing single unequal plain invert branch of required degree : Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 100x100x75 mm

Providing and fixing Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905 65 mm offsets With 100 mm dia pipe

65 mm offsets With 75 mm dia pipe

Providing and fixing Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905 130 mm offsets With 100 mm dia

130 mm off sets With 75 mm dia

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS: 3989

Providing and fixing C.P. brass bottle trap for wash basin including CP waste fittings complete 32 mm dia complete in all respect of approved quality.(Jaquar)

Providing and fixing terminal guard 100 mm Sand cast iron S&S as per IS - 1729

Providing and fixing collar : 100mm

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete 450 mm dia RCC pipes.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded 300 mm diameter S. W. pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for manholes Size 120x90 cm With F.P.S brick class designation 75

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collectingsamples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. All types of soil 400 mm dia All types of soil 400 mm dia

Rocky strata including Boulders 400 mm dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed/plain bevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm dia

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 110 mm

Bend 87.5° 110 mm bend

Shoe (Plain) 110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

250 mm dia. R.C.C. pipe

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm precast R.C.C. horizontal grating with frame and vertical grating complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil

WBM Grading 1 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 1 as per Technical Specification Clause 404. By Manual Means

Providing and laying in position ready mixed plain cement concrete, using fly ash and cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. All works upto plinth level: M-10 grade plain cement concrete (cement content considered @ 220 kg/cum)

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).: Dark shade pigment using ordinary cement

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete.1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Excavation for Structures Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. Ordinary soil Upto 3 m depth

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 (For height upto 5 m) P.C.C. grade M 20 Nominal mix (1:2:4)

Brick masonry work in cement mortar in substructure complete excepting pointing and plastering, as per drawing and technical specification Clauses 602, 603, 604, 1202 & 1204 In 1:4 Cement mortar

Plastering with cement mortar (1:4), 15 mm thick on brickwork in substructure as per technical specification Clauses 613.4 & 1204

R.C.C grade M 20

Supplying, fitting and placing HYSD bar reinforcement (Fe 415) in substructrue complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202 (The reinforcement steel shall be procured from original (primary) steel producers as per clause no. 2011.3.1 of MORD specifications (First revision'2014) and IS 1786:2008 clause no. 1.6)

Construction of Embankment with Material Obtained from Roadway Cutting Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5

Trenching in ordinary soil up to a depth of 60cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling with in a lead of 50m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Renovating lawns including weeding, cheeling the grass, forking the ground, top dressing with sludge or manure, mixing the same with forked soil, watering and maintaining the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing and disposal of rubbish as directed, including supplying good earth if needed but excluding the cost of sludge or manure(the good earth shall be paid for separately)

Supplying and stacking sludge at site including royalty and carriage up to 1 km(sludge measured in stacks will be reduced by 8% for payment)

Supplying and stacking at site dump manure from approved source, including carriage up to 1 km (manure measured in stacks will be reduced by 8% for payment) screened through sieve of I.S. designation 4.75 mm

Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge.

Suply and plantation of mature trees including excavation of pit, providing manure and watering and caring for one year as per directions of Engineer-Incharge

STP & ETP with capacity of 40 KLD and Flow Rate 1 m3/Hr. with MBBR Technology.

Supply installation and commissioning of Zero B, water cooler with inbuilt UV water purification System, Cold, Normal, Display , Normal water storage capacity-Online Water, Cold water storage capacity-80 Ltr, Water cooling rate-60 LPH, Cold water temperature-15±2°C, No. of faucet-2 Nos. (1-Cold & 1-Normal), Indication: Dynamic Monitor and Controller (DMC),Blue backlit LCD display indicating temperature, TDS, bar graph for cartridge life, pump status, no water, flushing of membrane.Chiller indicator Green indicator for cooling ON",Outer body material Full stainless steel outer body (SS204cu), Storage Tank material Full stainless steel outer body (SS304), Weight (Kgs) 80±2 Kgs, Dimension(LXWXH) Inches 26.5X28.5X57.5, Compressor EMERSON/Tecumseh, Operating temperature 5 to 45°C ±2°C, Refrigerant R134 A Green Gas, Operating voltage 230±10% V AC, 50Hz, Current in amps (maximum) 3.5±0.5A, Power consumption (W) 700 Watts, Rejection of salts (TDS) Up to 90%, Pure water recovery 100%, Purification Capacity* Up to 120 LPH, Prefilter Dedicated sediment cartridge 10" (10 micron), Carbon filter Activated carbon block -10"(10 micron) filter cartridge complete in all aspects as per direction of Engineer In-charge.

WGSTLPT Point wiring in PVC conduit, with modular type switch. Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. Group C

WGSTLMIDTC Twin Control point wiring in PVC conduit, with modular type switch: Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.

WGSTLPP2 Power plug wiring in PVC conduit (2x4 sq. mm) Wiring for light/power plug with 2x4 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

WGSTLSB Circuit/ submain wiring in PVC conduit: Wiring fir curcuit/ submain wiring alongwith earth wire the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

TLWGEC Telephone wiring in PVC conduit: Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair

PVCCON S/F PVC conduit: Supplying and fixing of following sizes of PVC conduit along with accessories in surface / recess including painting in case of surface conduit, or cuttting the wall and making good the same in case of recessed conduit as required. 20 mm

MB S/F metal boxes: Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required. 75 mm X 75 mm X 60 mm deep

PTSWEB S/F modular type switch/ socket: Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch

3 pin 5/6 amp socket outlet

Telephone socket outlet

MODFREB S/F modular type electronic fan regulator: Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

LPACCPT S/F light plug point modular type accessories: Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

PPACCPT S/F power plug point modular type accessories: Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

CREB S/F ceilling rose: Supplying and fixing 3 pin, 5 amp. ceilling rose on the existing junction box/ wooden block including connection etc. as required

BRHOLD S/F brass holder: Supplying and flxing brass batten/angle holder including connection etc. as required.

Call Bell/Buzzer: Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

ITCFFSUR ITC fluorescent fitting directly on surface: Installation, testing and commissioning of pre-wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling / wall, including connection with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

ITCCFFC ITC ceiling fan with cover on fan box: Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq, mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

ITCEF450 ITC exhaust fan upto 450 mm sweep: Installation of exhaust fan upto 450 mm sweep in the existingopening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required.

LOUSHEF Fixing louvers/shutters for exhaust fan: Extra for fixing louvers/shutters complete with frame for a exhaust fan of all sizes.

PWTPMCBDB S/F TP MCB DB: Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door

6 way (4 + 18), Double door

MCBTPIS S/F TP MCB isolator: Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissoning etc. as required. 63 amps

MCBC S/F 'C' curve, SP MCB Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 600 mm width X 50 mm depth X 2.0 mm thickness

Supplying, installing by suspension on ceiling, testing and commissioning of following capacity Sandwich Type Rising Mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. 2500 A 50kA SC for 1 sec

Supply of AC 230/250 volts, 50 HZ energy efficient ceiling fan with standard down rod, blades, 3 nos. caps Model-ES-50 50/Velocity/Velocity HS (1200 mm Sweep) etc. complete in all aspects as per direction of Engineer in Charge. (Make- HAVELLS ) (Rate taken from Havells price list w.e.f. Jan 2020). 1200 mm sweep

900 mm sweep

Supply of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. complete.Model- Turbo Force SP (Make : Havells) 300 mm sweep 900 rpm ,complete in all aspects as per direction of Engineer in Charge. (Rate taken from Havells price list w.e.f. Jan 2020). 300 mm sweep 900 rpm

Supply of heavy duty wall mounted fan - 400 mm dia Model - (D’zire) complete in all aspects etc. as per direction of Engineer in Charge (Make-HAVELLS) (Rate taken from Havells price list w.e.f. Jan 2020).

Supply of Ceiling Light Aluminium frame Environmental friendly, new generation,aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source, suitable for Armstrong/Grid ceiling (600X600mm) with electronic driver & high Brightness. complete in all aspects like Ballast , housing connecting wire etc. as per direction of Engineer in Charge. (Rate taken from Havells price list w.e.f. Jan 2020). Make-Havells

Supply & fixing of NU Bulb LED Mirror Light -9W (LHLDEUECNL8R009) ,6500k connecting wire etc.of standard make (Havell's) as per direction of Engineer in Charge. (Rate taken from Havells price list w.e.f. Jan 2020).

Supply and fixing of LED Tube light 20W (Code- LHEXARP7IN1W020) ,Lumen Output- 3000, 4000, 6500K, Wall mounted LED batten all in one fixture. complet in all aspects as per direction of Engineer in charge. (Rate taken from Havells price list w.e.f. Jan 2020).

Supply and fixing of Power coated Regal Batten type luminaire 1x36W FTL HF 240v,50Hz etc, (Code- LHFXBIG1IN1W036) ,with electronic ballast, complet in all aspects as per direction of Engineer in charge. (Rate taken from Havells price list w.e.f. 2018).

Supply of Recess Ceiling Light OCTANE LED PANEL ROUND Slim, compact, auminum die cast edge lit panel. Recess mounted round fixture (110MM DIA) ith opal diffuser and separate electronic driver. 6W LED, 6500k /4000k/3000K (Code- LHEBHDP5IZ1W006) as per direction of Engineer in Charge. (Rate taken from Havells price list w.e.f. Jan 2020). .

Supply & fixing of Wall Mounted Personal LED Luminaire 31W, 5700k Cat No- LW04-411-XXX-57-XX (Rate taken from Wipro price list w.e.f. 2017).

SUPPLY OF LED Glass Bulb B22, 15 W ,6000k /4000k/3000K ,230/250 Volt,50 HZ ETC, complete in all aspects as per direction of Engineer in Charge.

Supply and fixing of BULK HEAD light- 1 X 8 W CFL bulk head in die cast aluminium housing & frosted glasses complet in all aspects as per direction of Engineer in charge.

EARGIPL G.I earth plate electrode: Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

EARG125X6 S/L 25 mm x 5 mm G.I. earth strip in ground: Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required Above 120 sq. mm and upto 400 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 400 sq. mm (82mm)

Supplying and making outdoor cable and termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required 120 sq. mm

Supplying and fixing of light class G.I. pipe of 100 mm dia. (nominal) 3 metres length along the pole for protection of under ground cable as required.

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. Above 6.5 meter and upto 8.0 meter

Providing and making steel pole collar with cement concrete (1 cement : 3 coarse sand : 6 stone aggregate 20 mm) of specified size and shape including form work, plastering if required, curing etc. as required. (volume of pole/ pipe not to be deducted)

Supplying and erection of galvanised stay set for 11 KV over head lines complete with 19/ 20 mm dia X 1.8 metres long stay rod, anchor plate of size 45 cm X 45 cm X 7.5 mm thick, thimble, stay clamps, turn buckle ( 20 mm X 600 mm ), 7/ 4.00 mm dia G.I. stay wire and 11 KV strain insulator etc in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling etc. as required.

Supplying of two lengths of channel iron 75 mm X 40 mm X 6 mm (7.14 kg per metre) double pole cross arm for three wire 11KV over head line conductors complete with through bolts and nuts for clamping to the poles, 50 mm X 6 mm M.S. flats welded on one side to the channel iron and with bolts and nuts on the other side for tying the cross arms together, including drilling holes for insulator pins/ fittings, bolts, nuts and washers etc (as per drawing) and painting with primer and finish paint as required.

Supplying and erection of a set of cross bracing FRLSame work for 11 KV over head line double pole structure having four members fabricated out of 50 mm X 50 mm X 6 mm angle iron to form a rectangle of minimum size 1400 mm width X 2500 mm height , complete with 50 mm X 6mm M.S. flat iron clamps, bolts and nuts including drilling holes for insulator pins, bolts and nuts etc (as per drawing) and painting with primer and finish paint as required.

Erection of double pole 3 wire cross arm for 11KV/ 22KV/ 33 KV over head lines as required.

Supplying and erection of 11 KV pin insulator complete with large steel head G.I. pin, nuts, washers etc. as required.

Supplying and erection of 11 KV disc insulator for 11 KV over head lines with galvanised insulator fittings, ball and socket type and complete with galvanised strain clamps, bolts, nuts, washers etc. as required.

Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required.

Supplying, installation, testing & commisioning of following capacity End Feed Unit for the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required 800 A 50kA SC for 1 sec

1250 A 50kA SC for 1 sec

Supply,of following sizes of PVC sheathed LT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes. 3.5c x 500 sq.mm cable

3.5c x 240 sq.mm cable

3.5c x 185 sq.mm cable

3.5c x 70 sq.mm cable

3.5c x 50 sq.mm cable

4c x16 sq.mm cable

4c x10 sq.mm cable

4c x 6 sq.mm cable

HT XLPE CABLESSupply,of following sizes of PVC sheathed HT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes. 3.5 C X 240 sq.mm cable

Supply of Decorative gate light Globe shaped post top lantern in high grade unbreakable polycarbonate material suitable for retrofit LED (LHFXBON1TN5Q020)lamp B22 base. Upto 20 W.complet in all aspects as per direction of Engineer in charge. (Rate taken from Havells price list w.e.f. Jan 2020).

Supply of LED post Top with aluminium enclosure, powered with high power LEDs 72 W as light source and die casted heat sink exhibiting classic Victorian look with symmetrical light distribution, suspended mounting arrangement and excellent heat dissipation for long life standard make (Havells EROSPT72WLED757PSYMTOPC) complete in all aspects as per direction of Engineer in Charge. (Rate taken from Havells price list w.e.f. Jan 2020).

Supplying, installation, testing & commisioning of following capacity End Feed Unit for the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required 200 A 15kA SC for 1 sec

MAIN DISTRIBUTION BOARD Supplying, fixing, testing & commissioning of 415V ,3Phase 50Hz, 4wire system,sheet steel clad,dust & vermin proof cubical & indoor type floor mounted, free standing Main Distribution Board with IP - 42 protection, compartmentalized design and fabricated out of 2mm/1.6mm CRCA sheet steel complete with aluminium Bus Bars, Providing & Fixing of base plate /channel, P/F the following Switchgears,complete with earth Bus Bar throughout the length of the panel,terminal arrangement for incomings/outgoings cables and also outgoing terminations for various sizes of cables,the incoming and outgoing feeders shall be accommodated in a modular multi-tier arrangement,adequate size bus duct/cable alley, Sign writing,Painting,Earthing,Numbering,Danger plate etc. Compleete as requried,numbering, danger plate etc. complete as required as per specification and drawing. SMDB-GF INCOMER: 1 nos. 630A 415V, Ics=25KA, 4P MCCB with microprocessor release having O/L, S/C E/F,O/V & U/V protection. 1 nos. Digital type multi function meters (V+A+Hz) with cast resin CTs 600/5A. 1 Set of phase indicating lamp with MCB 1 nos TPN surge protection device of class 1& 2 BUSBAR 800A TPN Bus bar of aluminimum alloy. OUTGOING 3 nos. 20A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 3 nos. 25A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 1 nos. 32A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 1 nos. 50A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 2 nos. 63A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 7 nos. 80A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 3 nos. 160A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection.

ESMDB-F.F INCOMER: 1 nos. 63A 415V, Ics=25KA, 4P MCCB with microprocessor release having O/L, S/C E/F,O/V & U/V protection. 1 nos. Digital type multi function meters (V+A+Hz) with cast resin CTs 100/5A. 1 Set of phase indicating lamp with MCB 1 nosTPN surge protection device of class 1& 2 BUSBAR 100A TPN Bus bar of aluminimum alloy. OUTGOING 1 nos. 25A 230V, SP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 9 nos. 25A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection.

ESMDB-SF INCOMER: 1 nos. 400A 415V, Ics=25KA, 4P MCCB with microprocessor release having O/L, S/C E/F,O/V & U/V protection. 1 nos. Digital type multi function meters (V+A+Hz) with cast resin CTs 400/5A. 1 Set of phase indicating lamp with MCB 1 nos TPN surge protection device of class 1& 2 BUSBAR 630A TPN Bus bar of aluminimum alloy. OUTGOING 8 nos. 63A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 2 nos. 40A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 2 nos. 32A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection. 2 nos. 20A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection.

LIFT PANEL INCOMER 1 nos. 160A, 415V, 4P ATS. 1 nos. 160A 415V, Ics=25KA, 4P MCCB with microprocessor release having O/L, S/C E/F,O/V & U/V protection. 1 nos. Digital type multi function meters to show (V,A,KWh,KVAH,KW,KVA,PF,Hz) with cast resin CTs & communication port . 1 Set of phase indicating lamp with MCB 1 nosTPN surge protection device of class 1& 2 BUSBAR 1set of TPN Al. Bus bar of minimum of 200A capacity with heat shrinkable coloured sleeves & i/c DMC/SMC Busbars suports at required Intervals complete for cross section, size suports & their spacing etc. for with standing fault level of 25KA for 1 sec. OUTGOING 10 nos. 63A 415V, TP+N MCCB of 25KA with microprocessor based release having O/L, S/C protection & digital multi function (V+A+Hz ) with a set of cast resin CTs.

AUTOMATIC POWER FACTOR CONTROL PANEL(EEP) 500KVAR,IP Rating IP33, IP40, IP44, IP54, IP55, Single phase,three phase

Material and labour for CSS foundation of size 2.5x2.5x0.90m, brick masonry work in 1:6 with PCC 1:4:8 in top of plateform including feeling of boulder brick bats as directed by Engineer-in-charge.

Supply of 8.5 m long Tublor pole SP-23 with base plate and top cover plate complete in all respect.

Providing & Fixing Lightning Arresters System (Building protection)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately): Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin-charge

Toughened glass 12 mm thickness

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge. : Powder coated minimum thickness 50 micron aluminium tubular handle bar

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc.complete.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately).

Supply installation and commissioning of Passenger Elevator with machine room; Permanent magnet Motor, Product KONE I MiniSpace, Load & Capacity 1020 kg or 15 persons, Speed 1 m/s , Stops & Openings 5 stops & 5 openings, Single entrance car, Travel height 14.4 m, Elevator Grouping Duplex-Adjacent ,Full collective, 2a-DX Line separate Lcs , Well Dimension 2150 mm width and 2500 mm depth (required) Head Room height 3600 mm (required) ,Pit Height 1400 mm (required), MAP Floor Position Ex Machine room ,Car dimensions 1100 mm wide x 2150 mm deep x 2200 mm height, Door dimensions 900 mm wide x 2000 mm height, Door type Two-panel centre opening Plain Panel. FINISHES Car design Stainless Steel - Milkyway, Car Panel Finish Stainless steel Hairline, Handrail Round Bend Handrail Painted Traffic Black at Rear Wall, Ceiling & Lighting Integrated Roof RL75 Stainless Steel Pyramid Lighting LED, Flooring 3 mm PVC - Pattern Light Grey With Flecks, Car Door Finish Stainless steel Hairline, Car Operating Panel 1 Full Height Stainless Steel Face Plate ST4 - Silver brushed StSt Segmented LCD display Square surface mounted Buttons KDS90, Landing Signalization Stainless Steel 7 segment display Flush Mounted ST4-Silver brushed KDS90 complete in all aspects as per direction of Engineer In-charge.

Supply installation and commissioning of Passenger Elevator with machine room; Permanent magnet Motor, Product KONE I MiniSpace, Load & Capacity 1020 kg or 15 persons, Speed 1 m/s , Stops & Openings 5 stops & 5 openings, Single entrance car, Travel height 14.4 m, Elevator Grouping Duplex-Adjacent ,Full collective, 2a-DX Line separate Lcs , Well Dimension 2150 mm width and 2500 mm depth (required) Head Room height 3600 mm (required) ,Pit Height 1400 mm (required), MAP Floor Position Ex Machine room ,Car dimensions 1100 mm wide x 2150 mm deep x 2200 mm height, Door dimensions 900 mm wide x 2000 mm height, Door type Two-panel centre opening Plain Panel. FINISHES Car design Stainless Steel - Milkyway, Car Panel Finish Stainless steel Hairline, Handrail Round Bend Handrail Painted Traffic Black at Rear Wall, Ceiling & Lighting Integrated Roof RL75 Stainless Steel Pyramid Lighting LED, Flooring 3 mm PVC - Pattern Light Grey With Flecks, Car Door Finish Stainless steel Hairline, Car Operating Panel 1 Full Height Stainless Steel Face Plate ST4 - Silver brushed StSt Segmented LCD display Square surface mounted Buttons KDS90, Landing Signalization Stainless Steel 7 segment display Flush Mounted ST4-Silver brushed KDS90 complete in all aspects as per direction of Engineer In-charge.

Providind fixing installation and testing of 5 KVA capacity solar Power Plant (Off Grid)

Supply and fixing of C Cube Nurse call System, (NCS) with complete all accessories.

Supply , Installation , Testing and commissioning of CAT 6 UTP cable 23 AWG solid copper conductors Approved Makes: Belden/Dlink/Molex/Siemon/Panduit/Der Wiser

Supply , Installation , Testing and commissioning of loaded 24 port CAT6 jack panel for CAT6 cable termination Approved Makes: Belden/Dlink/Molex/Siemon/Panduit/Der Wiser

Supply , Installtion , Testing and comissioning of CAT6 information outlet (I/O) for CCTV Approved Makes: Belden/Dlink/Molex/Siemon/Panduit/Der Wiser

Supply , Installtion , Testing and comissioning of 1 or 2 port face plate white for I/O fixing at user side .Approved Makes: Belden/Dlink/Molex/Siemon/Panduit/Der Wiser

Supply , Installation , Testing and commissioning of CAT6 patch cord 3 feet for rack side switch termination .Approved Makes: Belden/Dlink/Molex/Siemon/Panduit/Der Wiser

Supply, Installation, Testing & Commissioning of 42 U Network Rack with 19''PDU 6 points 5 amp , Stationary shelf, Mounting Hardware(pac. Of 10) , Cable manager Horizontal 1U , Fan 230 vac 90 cfm top mounted . Approved Makes: Rittal/MTS/mass/Poweride/APC/APW

Supply, installation, testing and commissioning of UL Listed , ONVIF profile S & G , 1/2.8" CMOS, IP Vari Focal Dome Camera , Full, HD 3 MP , 2.8-12 mm Motorized Varifocal Lens, 30 FPS , Triple Stream with Edge Based Analytics , True Day/Night with IR Cut Filter with auto switch , Shutter Speed 1/5s ~ 1/20,000 s, IR Illuminator 30 Meter Min Effective Range, 120DB Wide Dynamic Range, Alarm 1/1, Audio 1/1, SD Card, H.265, H264 Compression, PoE, IP66 , Vandal Proof IK10 etc. Approved Makes :Hikvision/ honeywell/ tvs/Impulse/Axis

Supply, installation, testing and commissioning of UL Listed , ONVIF profile S & G ,1/2.8" CMOS, IP Vari Focal Bullet Camera , Full, HD 3 MP Resolution , 2.8-12 mm Motorized Varifocal Lens , 30 FPS , Triple Stream with Edge Based Analytics , True Day/Night with IR Cut Filter with auto switch , Shutter Speed 1/5s ~ 1/20,000 s, IR Illuminator 30 Meter Min Effective Range, 120DB Wide Dynamic Range, Alarm 1/1, Audio 1/1, SD Card, H.265, H264 Compression, PoE, IP66 etc.Approved Makes :Hikvision/ Honeywell/ Tvs/Impulse/Axis

Supply, installation, Testing and Commissioning of Open Platform ONVIF profile S &G Network Video Recorder, Intel based, Full Rack, RAID 0/1/5/10, @ 2M/30FPS, 1*2.5" SATA + 8 * 3.5" SATA, Throughput: 640 Mbps.1 X HDMI , 1X VGA ,, 1 X mic in , 1 X line out , USB 3.0 x 2 + USB 2.0 x 3 , 1 X WAN port , 1 X LAN port , pre-installed VMS :Approved Makes :Hikvision/ Honeywell/ Tvs/Impulse/Axis

Supply, Installation, Testing & Commissioning of 4TB HD Approved Makes: WD ,segate /Toshiba

Supply, Installation, Testing and Commissioning of Full HD 65" LED Professional Display Panel. Approved Make :- Samsung,Sony, Panasonic

Supply, Installation, Testing & Commissioning of 24 Port POE+ Access Switches with switching capaticy of 128 Gbps, forwarding performance 95 Mpps, having 24 x 10/100/1000BASE-T PoE-plus(RJ45) with minimum PoE budget of 370W and 4x 10G SFP+ uplink ports . Should support min 2GB internal DRAM, 2GB internal Flash memory,32K MAC address, 1K IPv6 Multicast Routes, Should have static Routes from day 1.One year support. Approved Make : Cisco/ Impulse / Juniper / Extreme/ Arista

Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); Memory: 4GB, NON-ECC, 1600MHZ; RAM: 4GB (1x4GB) Non-ECC DDR3 1600MHz SDRAM Memory; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; 20" TFT Monitor; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit. Approved Makes: HP,Dell,IBM

Supply Installation Testing Commissioning of Mitsubishi Electric Highwall Units inverter based (100% imported type) with outdoor bracket as per below specs 5 STAR 1.5TR COOLING ONLY MODEL: MSYGN18

Supply Installation Testing Commissioning of Copper Tubing including chiselling in walls whwereever required as per below specs 6.35mm / 12.7mm with 9mm invidual slevve insulation

Supply Installation Testing Commissioning of Copper Tubing as per below specs 2.5mm 4 Core Copper

Supply Installation Testing Commissioning of Drain Tubing as per below specs 25mm (10kg/sq inch) insulated in tube type nitrile insulation of 6 mm

Supply, installation, testing and commissioning of following sizes ISI markedHeavy duty MS 'C' class pipe including cutting, welding etc. and providing all fittings such as bands, tees, reducers, flanges, gaskets, nuts, tie rods, anchor fastnor, chili clamps, bolts and washers etc. including with two coat of red oxide primer and one coat of post office red paint etc. complete as required. the minimum size of the pipes as following. Make : Jindal / Surya / Swastik / Equivalent 25mm (app.)

80mm (app.)

150mm (app.)

Supply, installation, testing and commissioning of stainless steel single headed landing valve conforming to IS - 5290 with 63 mm dia. instantaneous female coupling on the outlet with PVC blonde cap and chain, necessary companion flanges, nuts, bolts, washer and gasket complete as per specification. (ISI marked) Make : Life guard / Safe Fire / Kalpex / Palex / Equivalent

Supply, installation, testing and commissioning of 63 mm dia. 15m long reinforce rubber lined hose pipe including stainless steel male and female instantaneous type coupling, machine wound with copper wire complete in all respects. (ISI marked) Make : Life guard / Safe Fire / Kalpex / Palex / Equivalent

Supply, installation, testing and commissioning of 63mm dia. stainless steel short branch pipe nozzle suitable for instantaneous connection to hose coupling as required. Make : Life guard / Safe Fire / Kalpex / Palex / Equivalent

Supply and installation of MS hose box keeping two numbers of RRL hose pipe and one number of short branch pipe nozzle with necessary fitting like anchor fastnor, fastnor nuts etc. as required. Size: 750mm x 600mm x 300mm

Supply, installation, testing and commissioning of swinging type first aid fire hose reel of 20mm dia and 30mtr. length made rein forced rubber tubing, MS drum with fixing bracket with 5mm shut off nozzle. Make : Life guard / Safe Fire / Kalpex / Palex / Equivalent

Supply, installation and testing of 25MM dia ball valve including union, hold tight, suta etc. Make : Speed / Kartar / Castle / Equivalent

Supply, installation and testing of cast iron body butterfly valve, wafer end type as per IS : 13095 including lever key complete with all fitting like MS flanges, nuts, bolts, gaskets etc. Make : Castle / Katar / Equivlent 150 mm dia

Supply, installation and testing of air release valve including necessary fittings etc. Make : Kartar / Castle / Equivalent

Supply, installation, testing and commissioning of following sizes ISI marked Heavy duty MS 'C' class pipe including cutting, welding etc. and providing all fittings such as bands, tees, reducers, flanges, gaskets, nuts, tie rods, anchor fastnor, chili clamps, bolts and washers etc. including with two coat of red oxide primer and one coat of post office red paint etc. complete as required. the minimum size of the pipes as following. Make : Jindal / Surya / Swastik / Equivalent 25mm (app.)

80mm (app.)

Supply, installation, testing & commissioning of 68* auto bust sprinklers with socket. Make : Life guard / Safe Fire / Omex / HD / Equivalent Sprinkler pendent type ( 68* )

Supply, installation, testing and commissioning of cast Iron body non return valve, complete with necessary fitting like MS flanges, nuts, bolts, gasket etc. as required. Make : Castle / Kartar / Equivalent 80mm dia

Supply, installation and testing of 25MM dia ball valve including union, hold tight, suta etc. Make : Speed / Kartar / Castle / Equivalent

Supply, installation, testing and commissioning of SS flexible hose pipe 750mm upto 1000mm long with fittings as required (if required )

Supply, installation, testing and commissioning of following sizes ISI marked Heavy duty MS 'C' class pipe including cutting, welding etc. and providing all fittings such as bands, tees, reducers, flanges, gaskets, nuts, tie rods, anchor fastnor, chili clamps, bolts and washers etc. including with two coat of red oxide primer and one coat of post office red paint etc. complete as required. the minimum size of the pipes as following. Make : Jindal / Surya / Swastik / Equivalent 25mm (app.)

80mm (app.)

Supply, installation, testing & commissioning of 68* auto bust sprinklers with socket. Make : Life guard / Safe Fire / Omex / HD / Equivalent Sprinkler pendent type ( 68* )

Supply, installation, testing and commissioning of cast Iron body non return valve, complete with necessary fitting like MS flanges, nuts, bolts, gasket etc. as required. Make : Castle / Kartar / Equivalent 80mm dia

Supply, installation and testing of 25MM dia ball valve including union, hold tight, suta etc. Make : Speed / Kartar / Castle / Equivalent

Supply, installation, testing and commissioning of SS flexible hose pipe 750mm upto 1000mm long with fittings as required (if required )

Supply, installation, testing and commissioning of following sizes ISI marked Heavy duty MS 'C' class pipe including cutting, welding etc. and providing all fittings such as bands, tees, reducers, flanges, gaskets, nuts, tie rods, anchor fastnor, chili clamps, bolts and washers etc. including with two coat of red oxide primer and one coat of post office red paint etc. complete as required. the minimum size of the pipes as following. Make : Jindal / Surya / Swastik / Equivalent 25mm (app.)

80mm (app.)

Supply, installation, testing & commissioning of 68* auto bust sprinklers with socket. Make : Life guard / Safe Fire / Omex / HD / Equivalent Sprinkler pendent type ( 68* )

Supply, installation, testing and commissioning of cast Iron body non return valve, complete with necessary fitting like MS flanges, nuts, bolts, gasket etc. as required. Make : Castle / Kartar / Equivalent 80mm dia

Supply, installation and testing of 25MM dia ball valve including union, hold tight, suta etc. Make : Speed / Kartar / Castle / Equivalent

Supply, installation, testing and commissioning of SS flexible hose pipe 750mm upto 1000mm long with fittings as required (if required )

Supply, installation, testing and commissioning of main fire alarm panel supply source (230AC 50 Hz and 24 V DC) 24V out put supply for detector. fault indication open, short circuit in detector line. visual indication fire, fault, open, short & system . Make : Agni / Equivalent 10Zone

Supply, installation, testing and commissioning of MS body electronic sounder ( hooter ). Make : Agni / Equivalent

Supply, installation, testing and commissioning of MS body manual call point. Make : Agni / Equivalent

Supply, installation, testing and commissioning of Somke Detector for Rooms. Make : Agni / Equivalent Ground Floor

Supply, installation, testing and commissioning of Somke Detector for Rooms. Make : Agni / Equivalent First Floor

Supply, installation, testing and commissioning of Somke Detector for Rooms. Make : Agni / Equivalent Second Floor

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required. Make : Agni / Equivalent

Supply, Laying, Installation, Testing and Commissioning of armored & unarmored copper conductor. The minimum size of the cables as following. Make : Havells / Polly cab / Gloster 2C X 1.5Sq.mm.( Copper unarmored)

Supply, laying, testing and commissioning of 20mm PVC conduit along with accessories complete as required. Make : Sidhbali / Kalinga / Equivalent

Fire Extinguishers Supply and installation of ABC 4Kg type fire extinguishers. Make : Life guard / Safe Fire / Kalpex / Palex / Equivalent

Supply and installation of CO2 4.5Kg type fire extinguishers. Make : Life guard / Safe Fire / Kalpex / Palex / Equivalent

Supply and installation of Mechanical Foam 9Ltr. Type fire extinguishers. Make : Life guard / Safe Fire / Kalpex / Palex / Equivalent

OXYGEN & NITROUS SYSTEM Supply,installation ,testing commissioning of the following Medical Gas Pipe line system conforming to the specification and relevant International standards. the work not Included any civil and other electrical works. the warranty period from the system will be 12 month for the date of commissioning and handing over the same. 8+8 size manifold extendable type along with Non Return Valves for every cylinder and copper pig tail pipe W/O Cylinder.

Fully Automatic Control panel for the Oxygen with changeover system.

Emergency supply system oxygen of Four +4cylinder ( without cylinder)

Surface mounted front loading Oxygen Gas outlets Point . CE with CE NO.

Probe for above outlet point.

Oxygen flow meter 0-15 LPM with humidifier bottle.CE

4+4 size Nitrous Oxide manifold extendable type along with Non Return Valves for every cylinder and copper pig tail pipe W/O Cylinder.

1+1 Emergency Nitrous oxide system

Semi Automatic control Panel for Nitrous oxide

Nitrous oxide outlet Point

Nitrous oxide Probe

VACUUM Supply,installation ,testing commissioning of the following Medical Gas Pipe line system conforming to the specification and relevant International standards. the work not Included any civil and other electrical works. the warranty period from the system will be 12 month for the date of commissioning and handing over the same Surface mounted front loading Vacuum Gas outlets Point .CE

Probe for above outlet point.

Ward Vacuum Unit with Regulator, Collection Jar of 600 ml with Bracket.CE

Low pressure tube for vacuum

Vacuum system DUPLEX consisting of the vacuum pump model 15V -2No with 10 HP motor, Vacuum receiver of 2000 liters capacity with bactrial filter

Theatre Suction Unit, trolley mounted with 2 nos. 2000 ml Collection Jars

COMPRESSED AIR Supply,installation ,testing commissioning of the following Medical Gas Pipe line system conforming to the specification and relevant International standards. the work not Included any civil and other electrical works. the warranty period from the system will be 12 month for the date of commissioning and handing over the same Surface mounted front loading Compressed Air Gas outlets Point 4 bar . CE with CE NO.

Probe for above outlet point.

Compressed air system two with 10 HP motor air receiver for 1000 liters for other related equipments with all filtration system .

MEDICAL GRADE COPPER PIPE : Medical Grade with Imported fitting solid drawn seamless, deoxide non arsenical, half hard, tempered and the degressed, mfd as per the BS 2871 part 1 Table -X of 1971 and EN 13348 the chemical composition. With Lloyd certified . 54mm OD x 1.2mm thick

42mm OD x 1.2mm thick

28mm OD x 0.9mm thick

22mm OD x 0.9mm thick

15mm OD x 0.9mm thick

12mm OD x 0.7mm thick

Valve Box powder coated complete with front glass cover, pressure gauges, Lock etc. complete. for 4 gases

For 3 gases

for 2 gases

Digital Medical Gas Alarm System with low, normal & high pressure indication. Master Alarm system

For 4 gases

for 3 gases

for 2 gases

CASCADE SYSTEM Automatic control panel with duplexing and cascading for vacuum pump and the compressed air system

H.P. antistatic rubber tube for Oxygen,Nitrous,Air and Vacuum Imported

Hand shutoff valve for outlet point

2 Way RMU Unit 11kV, 630A, 21kA/3sec, SF6 Gas Insulated, Outdoor, Extensible Type Compact Switchgear with 1 No. Motor Operated Vacuum Circuit Breakers as Incomer, 1 Nos. Motor Operated Vacuum Circuit Breaker as Outgoing, 1 Nos. Air Insulated Metering Module (Configuration: VVVV+M) SafePlus compact switchgear Total number of modules 1 pcs.

400 KVA Transformer Supply,Installation, Testing & Commissioning of of 400 KVA Transformer 11/0.433KV, 3Phase, 50Hz, Dyn 11, Out door ONAN type, ON Load Tap Changing with Remote Tap Change Over Unit arrangement on HV side, , 11kV (ONLY LEVEL3 LOSSESS)

Supply and installation of 70 sqmm H.T cable.