Special repair to Bldg No. P-191/01 to 06 at Mil Stn Dharamshala

Amount

Taking down chowkhats or frames n.exc 1.50 sqm with shutters (without taking off shutters from the frames) complete all as specified.

All as per Srl Item No 1.00 here-in-before, but exceeding 1.5 Sqm and n.exc 4 Sqm(without taking off shutters from the frames) complete all as specified.

35mm thick Ist class soft wood glazed and skeleton shutters, open rebated and prepared to receive glass or gauge etc ( divided into squares with plain chamfered or rounded , mitred and rebated sash bars, any numbers), edges of framing plain chamfered or rounded fitted with cut and mitered beads and fitted to chowkats for securing glass/gauge size of stiles rails and other parts as per clause 8.24 (a) of SSR Part-I complete all as specified & directed.

35mm thick factory made plain framed panelled shutters of 2nd class hard wood two panel with lock rail and panel of 9mm thick BWP commercial ply. The size of rail and stile as per IS-1003 (Part-I) Kiln seasoned and chemically pressure treated factory made shutters wood is to be incorporated complete all as specified & directed.

Pressed steel frame made out of MS sheet 1.25mm thick of size 125x 60 mm for doors/ windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc all as specified.

Pressed steel frame made out of MS sheet 1.25mm thick of size 105x60 mm for doors/windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc all as specified.

Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, or galvanized wire staples all as specified & directed.

M&L for cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in cills, steps, complete all as specified.

Box type Steel windows comprised of tubular frame and shutters made out of 1.25mm thick MS steel tube factory made with double side shutters wire gauged shutter & glass glazed shutter with side hung shutters with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 150mm long for each leaf and 8mm square bar grills at spacing as shown on drawing welded to F I frame work , incl other fittings ,hinges ,handles tarred hold fasts PCC blocks etc all as specified and directed by Engr-in- Charge. Note-: Wire and glass panes shall be measured and paid separately. Drg No:-CEPZ/C-TD/27/13 dt 11-09-2013 sheet 4/4.

Steel ventilator with centre hung shutter including two pairs of brass cup pivoted catch spring and pulley wheel , all as specified and directed by Engr-in- Charge.

3mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares size n.exc 0.5 sqm in each pane all as specified and directed.

Figured glass pin head type 3 mm thick ordinary quality and glazing with oil putty not exc 0.5 Sqm in each pane all as specified and directed.

Aluminium alloy, anodised,sliding door bolt with hasp, staple ( bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded setion or cast aluminium alloy and fixed 250 mm long all as specified and directed.

Anodised aluminium barral tower bolt extruded section 200 mm size all as specified and directed.

Anodised aluminium handle cast type 125 mm size all as specified and directed.

300mm, ordinary rat tail rod pattern springs, including roller and roller plate complete, fixed in repairs all as specified and directed.

Preparation of new or previously untreated Steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer all as spd and directed.

Complete removal of existing treatment from wall all as spd and directed.

Preparation of new wood or wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint complete.

Taking down cement plaster on brick walls or stone walls any descrition etc including raking out joints, hacking for key, scrubbing down with water etc all as specified and directed.

Rendering 10mm thick cement plaster on other than fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and fair without using extra cement all as specified and directed.

Rendering 05 mm thick cement plaster on faces of brick work or concrete surfaces in cement mortar (1:4) as in ceiling finished even and fair without using extra cement all as specified and directed.

15mm thick cement plaster in CM 1:4 on bricks or concrete surfaces finishing the surfaces even and smooth without using extra cement all as specified.

Rendering or plastering work 5 mm thick in CM 1:4 in fascia/edges/ceiling of Chajjas and roof projections etc, including taking out peeled off plaster / concrete and making the line in true shape and finishing the surface without using extra cement all as specified.

Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified Note-: Payment for providing grooves shall be made separately.

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to theedges of panels and finishing the groove complete as per specifications and as directed by the Engineer-in-charge.

Preparation of new plastered surface of wall by applying 1.5 mm wall care putty in two layer and making the surface smooth with sand paper and applying two coat of OBD complete all as specified & directed.

Preparation of old plastered surface of wall by applying 1.5 mm wall care putty in two layer and making the surface smooth with sand paper and applying two coat of OBD complete all as specified & directed.

Applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new /old surfaces complete all as specified & directed.

Two coats of white wash on new plastered surface of walls including preparation of surfaces all as specified and directed.

Two coat of white wash on old finished surface of ceiling including preparation of surfaces all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving n.exc 15 cm thick (below or above ground level) all as spd and directed.

25 mm thick cement concrete 1:2:4 Type B-0 as in floor finished even and rough to receive further floor finishes all as specified and directed.

Glazed ceramic tiles coloured, (first quality), of size 300x450mm x7mm thick on vertical surfaces such as skirting dados and risers to walls etc, joint free/joint less, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces over and including 10 mm thick rendering in CM 1:3 incl taking down existing tiles all as specified and directed.

Non skid edge cut ceramic coloured tiles 7mm to 8mm (square/rectangular) area each tiles exc. 0.06 sqm but not exc. 0.11sqm in floors etc & jointed in neat cement slurry and pointed in white cement and pigment over over 15mm thick screed bed in CM 1:4 including taking down existing tiles all as spd and directed by Engr-in Charge.

Non skid edge cut ceramic coloured tiles 7mm to 8mm (square/rectangular) area each tiles exc. 0.18 sqm but not exc. 0.38 sqm in floors etc & jointed in neat cement slurry and pointed in white cement and pigment over over 15mm thick screed bed in CM 1:4 including taking down existing tiles all as spd and directed by Engr-in Charge.

20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick screed bed in CM 1:4 including taking down existing stone slab all as spd and directed by Engr-in Charge.

Machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed cement screed base laid and jointed with grey camant slurry mixed with pigment to match the shade of slab including rubbing and polishing complete after roughing surfaces of old concrete floor by picking sweeping down with water to remove dust etc all as spd and directed.

Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete for risers of staircase incl rendering 10mm thick in CM (1:4) and finished rough. all as spd and directe.

Rotational moulded polyethiene water storage tanks (three layer) of capacity 500 litres, (cylindrical vertical with closed top) hoisted and fixed in position including 20mm ball Ball valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball including necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, checknuts & washer etc complete including dismantling existing water tank all as specified and directed.

Taking up or down steel water tubing and connections including cleaning for refixing or removal to store for bore of pipe 15mm bore dia all as specified and directed.

ditto- as per ser item No 38.00 above but 20mm bore all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed by Engr-in-Charge.

S&F 15mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc all as specified.

S&F 20mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc all as specified.

S&F in repair Angular Stop cock 15mm bore pipe ,CP cast copper alloy of complete all as specified and directed.

Bib taps for 15 mm bore pipe, cast copper alloy chromium plated fixed in repairs complete all as spd and directed.

M&L for 15 mm bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as spd and directed.

S&F Shower rose with arm for 15 mm bore pipe, cast copper alloy chromium plated fixed in repairs complete all as spd and directed.

S&F PVC flushing cistern 10 ltr capacity incl PVC connection inlet and and outlet connections,brackets, PVC flush pipe with bend 32 mm dia of suitable length including making necessary connections to water supply pipe line and jointing to WC all as specified and directed.

S&F in in repair Vitreous china ware Orissa pattern white water closet of size 580x440mm with integral foot rest including PVC (SWR) 'S' trap front or back inlet and connection to pipes (excluding flushing cistern but incl flushing pipe 32mm dia) complete all as specified and directed.

PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Ball valve high pressure of PTMT with epoxy coated alum rod & high density plastic ball screwed for 20mm bore iron pipe and fixed ( minimum weight 20mm -210 gms) complete all as specified and directed.

S & F in repairs Vitreous china wash basin, white flat back,size 550 x 400 mm including waste coupling , brackets and cutting for and pinning in ends of brackets or errecting stand and 32 mm dia waste pipe all as spd and directed

Supply only pillar tap 15 mm bore chromium plated screwed down, high pressure screwed for iron pipe complete all as specified and directed.

S & F concealed stop cock extra heavy duty with adjustable wall Flange size 15 mm bore chromium plated complete all as specified and directed.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as spd and directed.

Sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified.

S&F in repair soap dish any type fixed to plugs with chromium plated brass screws all as specified and directed.

Tubular towel rail, 20mm dia, D type, 60cm long between flanges aluminium anodised fixed in repairs all as specified and directed.

S&F in repair 20mm size gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed cast copper chromium plated fancy type alloy ISI marked with crutch or butter fly handles screwed down all as specified and directed.

S&F in repair 15mm size gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed cast copper chromium plated fancy type alloy ISI marked with crutch or butter fly handles screwed down all as specified and directed.

S&F 110mm dia PVC (SWR) bends any radius with oval access door in repair complete.

S&F 75mm dia PVC (SWR) bends any radius in repair complete.

S&F 75mm dia PVC (SWR) bends any radius with oval access door in repair complete.

S & F PVC (SWR) junction single, (Single T) equal or unequal 110 mm dia complete all as specified.

S & F PVC (SWR) junction single, (Single T) equal or unequal 75 mm dia complete all as specified.

S&F in repair 110 mm bore PVC (SWR) pipes single, socketed in any length with rubber ring joints fixed to walls incl dismantling existing pipes all as specified.

All as per Srl item 68 here-in-before, but 75mm bore.

S&F in repair 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified.

All as per Srl item 70 here-in-before, but 75mm bore.

S&F PVC (SWR) vent cowl for 75 mm dia all as directed by Engr-in-charge.

S&F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement fixed in cement concrete 1:2:4 type B-1 all as specified.

Cement concrete type C-1, 1:3:6 (using 20mm graded aggregate) as in plinth protection 75mm thick finished even and smooth without using extra cement complete.

Demolitin of brickwork built in cement mortar including all quions ,arches,pillars etc but excluding ashlar facings dressed stonework and pre cast concrete articles

Brick work with subclass 'B'bricks,straight or curved on plan exc 6m mean radius built in CM 1:6 all as specified.

M&L for 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified.

S & F Continuous (piano) hinges,Width of flaps 30 mm(when open), mild steel, bright finish or electro galvanised complete all as specified.

Hasp and staple 100mm in size, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified.

S&F 25 mm curtain rod, colour coated with wooden bracket and wooden funnel over door and window fixed with steel screw and PVC cleat complete all as specified.

S&F Floor door stopper of aluminium alloy body and tongue 140mm length of cover of plate, anodised, with hard drawn steel spring, fixed in floor complete.

Complete removal of existing roof treatment such as old APP membrane, polythene film, mud phuska and the like, complete all as specified and directed by Engr-in-Charge.

Applying a coat of cement slurry @ 3Kg/ Sqm including preparation of surfaces, complete all as specified and directed by Engr-in-Charge.

20mm thick screed bed in cement mortar 1:4 on concrete surface of roof or terracing surface, finished even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge. NOTE: WPC to be measured and paid separately).

Supply only liquid water proofing compound, complete all as specified and directed by Engr-in-Charge.

Applying one coat of primer conforming to IS: 3384-1986 over plastered surfaces @ 0.40 litres/Sqm of density 0.87-0.89kg/litres at 25°C and viscosity 70-160CPS ( primer shall be of same make as of memebrane), complete all as specified and directed by Engr-in-Charge.

APP (Atactic Poly-propylene polymer) modified membranes, five layered, 3mm thick weighing not less than 3.5 kg/Sqm, having a centre core of polyester non-woven mat (FP) reinforcement dipped into APP modified mix and sealing all the over laps 75mm on length side and 100mm on width side of membranes by torching as per manufacture's instructions by authorised applicator as per manufactureres instructions, complete all as specified and directed by Engr-in-Charge.

Rendering 15mm thick on brick work or concrete surfaces in CM 1:4 with and including water proofing compound to sunken portion with proper slope towards outside and finishing cement concrete or brick work surface even and smooth using extra cement including application of 90 micron polythene film and applying bitumen coating @ 3.00 Kg/Sqm (WPC shall measured and paid separately) all as specified and directed.

M&L for Broken brick coarse aggregate 40 mm nominal size filled under sunken portion after treatment and compacted to laying floor finishing all as specified and directed.

S&F factory made PVC solid door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as specified.

Factory made PVC moulded door shutter with particle board core 28 to 30mm thick (tiles) with 2, 4 or 6 raised panel design with 2mm moulded PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face complete all as specified.

100 mm thick PCC as in sub base Type C-2 1:3:6 40 mm graded aggreagate all as specified.

Chequered cement concrete tiles with grey cement and not pigment ,20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors complete all as specified & directed.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings, tube light fittings etc removing material to store for keeping in safe custody or for taking credit ( credit for above items should be made as per conditions separately ) and also making good disturbed surfaces of wall, floors etc all as specified and as directed by the Engineer-in-Charge.

M&L for point wiring with 1.5 Sqmm copper conductor (Multi-stranded) PVC insulated and unsheating FRLS electric cable 1100 volts cable and including PVC casing and caping of suitable size (as per conductor run) with all fittings/ accessories and including PVC insulated electric cable 1100 volts 1.5 Sqmm ( multi-stranded) copper conductor single core( Green colour) cable as continuous earth wire connected to common earth dolly including sunk sheet steel terminal box made out of 1.6 mm thick MS sheet covered with 3 mm thick plastic laminated sheet ( Make Hylum) concealed in wall or on surface as per site requIrement and making good disturbed surfaces of wall for one light point/bell point/fan point/exhaust fan point etc controlled by one, one way switch complete all as specified and as directed by the Engineer-in-Charge.

All as per Srl item No 96.00 above, but for one 3 pin socket outlet 5 Amp on same board complete all as specified and as directed by the Engineer-in-Charge.

All as per Srl item No 96.00 above, but for one 3 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

All as per Srl item No 96.00 above , but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor ( Multi-stranded) PVC insulated and unsheating electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common earth dolly complete all as specified and as directed by Engineer-in-Charge.

All as per Srl item No 96.00 above, but two way switch complete all as specified and as directed by the Engineer-in-Charge.

M&L for socket, 6A - 2/3 pin combined 2 module all as specified and directed.

M&L for socket, 6A/16A - 2/5 pin combined 2 module all as specified and directed.

M&L for Modular switch 1 way 6A, One module all as specified and directed.

M&L for Modular switch 2 way 6A, One module all as specified and directed.

M&L for Modular switch 1 way 16A, One module all as specified and directed.

M&L for Bell push Switch 5/6 Amp, 1 Module all as specified and directed.

M&L for call bell AC 230 volt single pole complete all as specified.

Sub main wiring single core PVC insulated and unsheathed cable two run 6 Sqmm multi -strand copper conductor drawing in PVC casing caping with 1 x 4.0 Sqmm earth wire as in earth and neutral complete all as specified and directed.

Ceiling rose surface type, 65 mm x 50 mm two to three terminals / PVC / polycarbonate, isolated body fixed on PVC block complete all specified and as directed by the Engineer-in-Charge.

Supply & Fix in replacement of existing unsrviceable Sheet metal enclosure for DB’s suitable for MCBs of single pole and neutral 08 way (Double door) with 200 amp 240 Volts rated bus bar all as specified. Note: i) Connections of MCB's shall be done with appropriate size of brass/Copper thimble. ii) The disturbed surface shall be match with existing surface.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and neutral, current carrying capacity 32 Amp complete all specified and as directed by the Engineer-in-Charge.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amp complete all specified and as directed by the Engineer-in-Charge.

Supply & fix in replacement of existing unserviceable Sheet metal enclosure with DB’s suitable for MCBs of triple pole and neutral 4 way, 415 volt, double door type with 200 amp rated bus bar double door type with one incoming and 04 outgoing Note: i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. ii) The disturbed surface shall be match with existing surface without any cost.

Supply and fix in replacement of MCB TPN/FP 40 to 100 Amp all as specified and directed.

Supply and fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-in-Charge.

Lamp holder, PVC/ polycarbonate type with back plate, complete all as specified and directed by Engr-in-Charge.

Supply and fix LED LAMP 9 W BC 6500 K all as per Wipro Code No N95001 or equivalent complete all as specified and directed by Engr-in-Charge.

Supply and fix LED street light fitting 15 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engr-in-Charge.

Taking down, re-fixing and connecting the existing serviceable electric meters single phase complete all as specified and directed by Engr-in-Charge.

Taking down, re-fixing electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etccomplete all as specified and directed by Engr-in-Charge.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.3mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 Metres below normal ground level, connecting to the Galvanised iron earth lead wire 4mm dia, by means of bolts, nuts, check nuts and washers of galvanised iron and 4mm earth lead protected by provision of GI medium grade pipe 15mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and with 6mm dia MS bar handle made to shape, GI medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of 75x50x6mm phosphorous bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 3 of SSR-2009 Part-I and connecting to earth test point including testing on completion all as specified and directed by the Engineer-in-charge.

Excavation in trenches not exc. 1.5 mtrs wide and not exc. 1.5 mtrs in depth in hard/dense soil getting out all as complete all as specified.

Returing , filling ,including spreading , levelling, watering and well ramming including moundas as in hard/ dense soil in layers not exc 25 cm complete all as specified.

Removing excavated materiel n.exc. 50 Mtrs and depositing where directed at a level n. exc. 1.5 mtrs above the strarting point in soil complete all as specified.

Sand cushioning to underground cables with a layer of sand 8cm before laying the cable and 15cm after lying the cable complete all as specified and directed by Engr-in-Charge.

Sub class (B* brick, old size, brick covering laid dry, flat transversally along the length of cable on sand cushioning, with width equal to the length of the brick, complete all as specified and directed by Engr-in-Charge.

Supply & laying XLPE insulated heavy duty electric power cables with multistranded aluminium conductor,1100 volts grade of size 25 sqmm 3.5 core complete all as specified and directed by Engr-in-Charge

Supply & fixing/ laying of GI pipe of size 40mm dia light grade laid in trenches/walls including clamps,screws etc complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement sheet metal enclosure of size 750x600x300mm made out of 2mm thick MS sheet suitable for fixing MCB/DB & meters, single door type with locking arrangement and reconnecting,commissioningand applying two coats of synthetic enamel paint over a coat of red oxide primer to internal and external surfaces with machine spray including necessary cutting/PCC work complete all as specified and directed by Engr-in-Charge. Note-: Disturbed surfaces shall be matched to existing surface.

Supply and fixing ball brass valves 15mm dia high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrulecomplete all as specified and directed by Engr-in-Charge.

Supply and fixing stop valves of size 15mm dia, cast copper alloy with crutch or butterfly handle, screwed both ends for fixing to GI pipe of size 15mm dia complete all as specified and directed.

KISHAN CONTRACTOR

VIJAY KUMAR LAKHNI

M/s Thakur Engineers