PWD/SE/KEC/NIT06/24-25

Amount

SITC of Automatic Lift (as per manufacturer design & as per detailed spectfication below conforming to IS) and putting into operation after final testing in the existing lift shaft complete with all accessories and reparing the damaged wall /floor if any etc to complete as required.

Make : OTIS / KONE/SCHINDLER

Type: Passanger Lift.

Load : 15/16 Passenger (1020/1088 Kg)

Control: Microprocessor based with AC variable voltage & variable frequency ( VVVF).

Machine:- Energy efficient machine, Gearless, Without Machine Room.

Speed: 1.5 Mtrs./ Sec

Floor served: G+7

Landing: 8 lands, all on same side

Total Rise : 25.7 Mtr (Approx) [Bidder should visit the site]

Operation: Microprocessor based simplex full collective with or without attendant.

Signals: Digital car position indicator,car travels direction indicator in car & at all landing with call registration indicator.

Travelling accuracy: ± 5 mm (Micro levelling arrangement)

Car inside: 1500 mm ( W ) x 2400 mm ( D ) x 2200 mm (H) or as per manufacturer's standard conforming to IS

Car Entrance: Clear Opening 900mm (W) X 2000mm (H) protected with car door.

Car Enclosure: Stainless Steel sheet (20 SWG) with Hairline finish with hand rail.

Car Ceiling & Lighting: Stainless Steel with hairline finish with LED lighting and Fan.

Car Ventilation: Pressure fan with anodised aluminium grill.

Car Flooring: Decorative granite flooring (As per direcion of EIC and according to this Department's Order).

Car Door: Stainless Steel centre opening automatic door provided with V3F controlled door drive system.

Landing Door: Stainless steel centre opening automatic door provided with V3F controlled door drive system.

Door Opening: Automatic power oprated door with full length Photocell assembly infrared light curtain sensor.

Car operating panel: A best quality Screen touch car operating panel with floor indication and digital hall position & direction indicatiors.

Landing operating panel: A best quality Screen touch car operating panel with floor indication and digital hall position & direction indicatiors.

Fire Rated Door: 2 Hours

PROTECTIVE DEVICES & OTHER ACESSORIES

ARD: Automatic rescue device complete with dry maintenance free batteries as required for automatic evacuation to the nearest floor in case of power failure / single phasing/others.

Overload Protection: Fully loaded with overload protection. On overloading condition the lift car will not start with door remaining open and give audio & display indication.

Emergency lighting in car: Battery operated emergency lighting in the lift car.

Intercom system: Battery operated Intercom System in Lift Car, Machine Room & Control Room.

Emergency Alarm: Battery operated alarm bell system in lift car and control room.

Fireman switch: Fireman switch at main landing terminal.

Voice Synthesizer: Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator.

Main rope - Belt Type (Flat Coated steel belt with V groove / Steel rope)

Communication & Monitoring the Lift : Lift controller/ Panel shall be Ethernet/Modbus ready with necessary converter, DC Power supply module etc. if required, and there should be single Ethernet/Modbus output from the Controller/panel and the same should be connected to BMS (Building Management System) and the controller/ panel should have also required for monitoring of real time data with date & time, maintenance-call back record, Mantrap notice, call records, location of car, Lift room temperature etc. should be noticed & display to in any desktop & mobile though wireless system.

Other works: Necessary cutting of wall/floor for fixing the Fire Alarm switch, all Button switch and also making provision to entry of rope, electric wire etc. as required to complete the job.

DIMENSION OF SHAFT & POWER SUPPLY

Available Shaft Dimension: 2000 (W) mm X 3000 (D) mm (Bidder should visit the site)

Pit Depth : 1600 mm (Bidder should visit the site)

Overhead : 4200 mm (Bidder should visit the site)

Electric power supply: AC 415V, 3Phase, 50Hz terminated at top floor adjacent to lift as per IS.

SITC of Automatic Lift (as per manufacturer design & as per detailed spectfication below conforming to IS) and putting into operation after final testing in the existing lift shaft complete with all accessories and reparing the damaged wall /floor if any etc to complete as required.

Make : OTIS / KONE/SCHINDLER

Type: Passenger Lift.

Load : 15/16 Passenger (1020/1088 Kg)

Control: Microprocessor based with AC variable voltage & variable frequency ( VVVF).

Machine:- Energy efficient machine, Gearless, Without Machine Room.

Speed: 1 Mtrs./ Sec

Floor served: G+3

Landing: 4 lands, all on same side

Total Rise : 10.95 Mtr (Approx) [Bidder should visit the site]

Operation: Microprocessor based simplex full collective with or without attendant.

Signals: Digital car position indicator,car travels direction indicator in car & at all landing with call registration indicator.

Travelling accuracy: ± 5 mm (Micro levelling arrangement)

Car inside: 2000 mm ( W ) x 2400 mm ( D ) x 2200 mm (H) or as per manufacturer's standard conforming to IS

Car Entrance: Clear Opening 900mm (W) X 2000mm (H) protected with car door.

Car Enclosure: Stainless Steel sheet (20 SWG) with Hairline finish with hand rail.

Car Ceiling & Lighting: Stainless Steel with hairline finish with LED lighting and Fan.

Car Ventilation: Pressure fan with anodised aluminium grill.

Car Flooring: Decorative granite flooring (As per direcion of EIC and according to this Department's Order).

Car Door: Stainless Steel centre opening automatic door provided with V3F controlled door drive system.

Landing Door: Stainless steel centre opening automatic door provided with V3F controlled door drive system.

Door Opening: Automatic power oprated door with full length Photocell assembly infrared light curtain sensor.

Car operating panel: A best quality Screen touch car operating panel with floor indication and digital hall position & direction indicatiors.

Landing operating panel: A best quality Screen touch car operating panel with floor indication and digital hall position & direction indicatiors.

Fire Rated Door: 2 Hours

PROTECTIVE DEVICES & OTHER ACESSORIES

ARD: Automatic rescue device complete with dry maintenance free batteries as required for automatic evacuation to the nearest floor in case of power failure / single phasing/others.

Overload Protection: Fully loaded with overload protection. On overloading condition the lift car will not start with door remaining open and give audio & display indication.

Emergency lighting in car: Battery operated emergency lighting in the lift car.

Intercom system: Battery operated Intercom System in Lift Car, Machine Room & Control Room.

Emergency Alarm: Battery operated alarm bell system in lift car and control room.

Fireman switch: Fireman switch at main landing terminal.

Voice Synthesizer: Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator.

Main rope - Belt Type (Flat Coated steel belt with V groove / Steel rope)

Communication & Monitoring the Lift : Lift controller/ Panel shall be Ethernet/Modbus ready with necessary converter, DC Power supply module etc. if required, and there should be single Ethernet/Modbus output from the Controller/panel and the same should be connected to BMS (Building Management System) and the controller/ panel should have also required for monitoring of real time data with date & time, maintenance-call back record, Mantrap notice, call records, location of car, Lift room temperature etc. should be noticed & display to in any desktop & mobile though wireless system.

Other works: Necessary cutting of wall/floor for fixing the Fire Alarm switch, all Button switch and also making provision to entry of rope, electric wire etc. as required to complete the job.

DIMENSION OF SHAFT & POWER SUPPLY

Available Shaft Dimension: 2000 (W) mm X 2750 (D) mm (Bidder should visit the site)

Pit Depth : 1600 mm (Bidder should visit the site)

Overhead : 4200 mm (Bidder should visit the site)

Electric power supply: AC 415V, 3Phase, 50Hz terminated at top floor adjacent to lift as per IS.

Terms & Condition

i) The Agency must procure the materials from the Manufacturer / OEM or from their authorised sales channel so that the standard warranty / support of the Manufacturer / OEM becomes applicable to the products to be delivered and installed by them.

ii) Documents that authenticates such procurement from the Manufacturer / OEM or from their authorized sales channel and standard warranty / support should be sent from the e-mail of the Manufacturer / OEM / authorized sales channel to the e-mail of Engineer-in-Charge and hard copy of it to be submitted during execution, of work/submission of bill.

iii) The rate quoted by the manufacturer should be inclusive of cost for providing 2 years DLP after completion of 1 year of initial commisioning.

iv) Rates should be quoted with minor civil works, wall cutting and mending good the damages to the original finish. (Rates should be inclusive of all Taxes & Duties)

SCHINDLER INDIA PRIVATE LIMITED