REPAIR TO SECURITY WALL, FENCING, GATES, ANGLES, POSTS, BARBED WIRES AND OTHER MISC B/R WORK AT BARAMULLA (ZONE I TO III) UNDER GE 969 EWS

Amount

Taking down cement plaster on brick or stone walls etc incl raking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed.

Demolition of brick work or stone masonary built in cement mortar including all quoins arches pillars etc all as directed but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and as directed.

Demolition of cement concrete (reinforced) in any position and any thickness (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings any thickness (below or above ground level) complete all as specified and as directed.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces finished even and smooth with using extra cement in cement mortar (1:4) complete all as specified and as directed.

M&L for dubbing out average 10mm thick in cement mortar (1:4) on irregular face of walls (when specifically ordered in writing) complete all as specified and as directed.

M&L for rendering 15 mm thick on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing finished even and smooth with using extra cement in cement mortar (1:4), complete all as specified and as directed.

M&L for preparation of newly or previously untreated surfaces and finishing wall surfaces with Acrylic Smooth exterior paint of required shade with two or more coat applied @ 1.67 ltr/10 sqm and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and as directed.

M&L for complete removal of existing treatment on old wall surfaces & Finishing walls with Acrylic Smooth exterior paint of required shade with two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) new surfaces or old decorated surfacs complete all as specified and as directed.

Preparation of old surfaces and applying one coat of cement base paint on walls surfaces /weather boardings complete all as specified and as directed.

M&L for complete removal of existing treatment of surfaces and applying two coats of cement base paint on walls surfaces/weather boardings etc, complete all as specified and as directed.

M&L for cement concrete type D-2 1:4:8 (using 40mm graded aggregate) as in foundations, filling and mass concrete, complete all as specified and as directed.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan n.exceeding 6m mean radius built in CM (1:4) complete all as specified and as directed.

M&L for walling or random rubble,uncoursed well bounded bedded and solidly hearted, built in cement mortar (1:6) complete all as specified and as directed.

M&L for providing cement concrete 1:2:4 type, B-1 (using 20mm graded crushed stone aggregate) as in coping, benching including all necessary form work complete all as specified and as directed.

M&L for RCC (nominal mix) Type B-1 1:2:4 (20mm graded aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for precast cement concrete type B-0 1:2:4 (12.50mm graded aggregate) louvres and jallies, 25mm thick (measured solid), including all mouldings but excluding frame set in cement mortar (1:4) complete all as specified and as directed.

Providing Precast cement concrete Type B-1 1:2:4 (using 20 mm graded crushed stone aggregate) in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water throughs, mangers, shelves and similar articals with plain faces set in CM (1:6) complete all as specified and as directed.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and ncluding mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

Dismantling trellis work (Jafri) (One way), including taking as under of battens in trellis (posts and rails measured separately) complete all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) embeded in cement concrete any section, including taking out embedded portion and making good disturbed ground complete all as specified and as directed.

M&L for cement concrete type C-2 1:3:6 (using 40mm graded aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L second class soft wood clean sawn as in scantling in framed and fixed work etc complete all as specified and as directed.

S&F 2nd class softwood 35mm x 10mm laths (fixed straight or diagonally) in two way trellis work with 50mm spaces in the clear, including 75mm x 50 mm fillet (notched to take ends of laths) all round and fixed, complete all as specified and as directed.

M&L for preparation of newly or previously untreated wooden surfaces of any description, not otherwise described, over 10cm width or girth, applying two coat of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

M&L for preparation of old wooden surfaces of any description, not otherwise described, over 10cm width or girth, applying two coat of synthetic enamel paint complete all as specified and as directed.

S&F Stainless steel 304 Grade railing top & bottom 40x40mm and horizontal 40x40mm centre to centre spacing 150mm and height upto 0.80m above GL including baluster 0.60m c/c complete including connected works rquired for fixing in floor PCC type B-1. 1:2:4 and making good of damage/ disturbed area and incl dismantling existing railing. Design and pattern as approved by Engr-in-Charge complete all as specified and directed.

M&L for 75mm thick cement concrete type C-2, 1:3:6 (40mm graded agrregate) as in sub base of floors, finished even and fair over well/rammed/compacted earth complete all as specified and as directed.

M&L for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and as directed.

S & F Chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors including screed bed 15mm thick comple in CM (1:4) complete all as specified and as directed.

M&L for providing cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in roof kerbs or mud stop, rounded or chamfered on edges, complete all as specified and as directed.

Dismantling fencing wire mesh, any type complete all as specified and as directed.

S&F mild steel posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc. flat iron fillets for securing wire mesh etc including MS bars for tightning chain link necessary drilling bolting reveting etc. & similar work, fence with all nut & bolts complete conforming to Fe- 410 - or Fe-310-0, complete all as specified and as directed.

M&L Mild steel round bars 10mm dia and over cut to length bent to shape required including cranking, bending, spirally for hooping, columns hooking ends including binding with and including MS wire (annealed) not less than 0.9mm dia or securing nuts clips, Fe-410-W (Gde.E-250) quality-A or Fe 290 (Gde - E-165) complete all specified and as directed.

S&F for 10 mm dia MS screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other ends or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 5cm long and n.exc 10 cm long, complete all as specified and as directed.

Supply only chain link MS galvanised fecing any size or type, complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size & type to any type of standards, rails, straining bolts etc including provison of binding wire, complete all as specified and as directed.

Applying two coats of synthetic enamel paint on steel & iron surface of any description, not otherwise described, over 10cm width or girth including preparation of new surface and applying one coat of red oxide zinc chrome, complete all as specified and as directed.

Applying two coats of synthetic enamel paint over a coat of red oxide on steel & iron surface of Surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint, complete all as specified and as directed.

S&F framed work such as grills, gratings etc, with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framed work of water tanks & similar work conforming to Fe-290-O Gde E-165 including dismantling, complete all as specified and as directed.

S&F portions framed & hung as gates, including pintle hinges, stops hand made sliding bolts etc, with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framed work of water tanks, guide rails of steel sliding door, rollers for sliding door to move steel sliding door & similar work conforming to Fe-290-0 Gde E-165 including dismantling, complete all as specified and as directed.

S&F pre-painted galvalume aluminium zinc coataing GI based profile steel sheet 0.50 mm thick of any colour having tnsile strength of 550 MPA as in roof covering/cladding to wall,fixed with self tappping screw incl dismantling, complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws incl dismantling, complete all as specified and as directed.

S&F galvanised,corrugated mild steel sheeting 0.63 mm thick with two corrugations side lap, fixed with coach screw and washers in roofs, walls etc incl dismantling, complete all as specified and as directed.

S&F 0.80 mm plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 120 gm incl dismantling, complete all as specified and directed.

Preparation of old painted galvaniised surfaces (on CGI/PGI roof sheet) of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

Preparation of old painted galvaniised surfaces (on CGI/PGI roof sheet) of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and as directed.

Dismantling floor hearth wall tilling including cement mortar bedding, removing serviceable tiles to store and rubbish of the permishes, complete all as specified and as directed.

M&L for glazed ceramic tiles in vertical surface 450x300x10 mm thick colour and design (as approved) in vertical surface and jointed in neat cement slurry and pointed in whiter or colour cement to match the colour of tiles over 15 mm thick cement plaster using CM (1:4), complete all as specified and directed.

M&L for 20mm thick granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Note:- Schedule of credit Rs. 68,403.00 will be deducted from total amount quoted while accepting the bid. Details of schedule of credit is given in tender documents.

M/S BHAT AND CO

M/S GHULAM QADIR WANI AND SONS

M/s ABDUL AHAD AND SONS

HAYAT TRADING CORPORATION

M/S NISAR AND CO

ALI MOHD NAJAR

M/s ABDUL QAYOOM LONE & BROS