Setting up of Studio and Audio Booth at Livestock Management Training Centre, Thiruvananthapuram

Amount

CIVIL WORK

15.3 : Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

15.60 : Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

6.4.1 : Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:Cement mortar 1:4 ( 1 cement : 4 coarse sand)

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

od67349/2023_2024 : Providing and fixing plain lining with necessary screws/nuts/& bolts/nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in-charge ( Frame work shall be paid for separately)<br>18 mm thick commercial ply

50.10.1 : Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

od67352/2023_2024 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 75 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the framework with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for the board as per manufacturer's specification and direction of the engineer in charge all complete.<br>100 mm overall thickness partition with 12.5 mm thick tapered edge gypsum moisture-resistant board conforming to IS : 2095: part I

12.45.3 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum moisture resistant board

od67354/2023_2024 : Providing and fixing of tile Carpet in the floor area complete as per the engineer in charge.

50.9.1.1 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood

9.53 : Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

od67355/2023_2024 : :Providing and fixing 90cm X 3.2cm X 210cm Acoustic Door Shutter including high load bearing<br>hinges and door handle of required size with necessary screws, The door will be filled with high acoustic<br>materials of silent board, Two layers of Acoustic foam ,Two layers of absorb wool. All complete as per direction of Engineering in charge

od67356/2023_2024 : Providing and fixing 120cm X 3.2cm X 210cm Acoustic Door Shutter including high load bearing<br>hinges and door handle of required size with necessary screws, The door will be filled with high acoustic<br>materials of silent board, Two layers of Acoustic foam ,Two layers of absorb wool. All complete as per direction of Engineering in charge.

od67357/2023_2024 : Providing and fixing Automatic heavy duty hydraulic double speed alloy door closer suitable for right and left hand opening doors, mounting on door panel or door frame (having brand logo with ISI, IS : 3564, embossed on the body and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.-for acoustic door

od67358/2023_2024 : Supply and installation of glass window using two layers of 6mm glass with wooden farme.

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.88 : Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

13.62.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture .

od67359/2023_2024 : Providing and fixing 9mm thick PET Polyester Acoustic panel. complete as per the<br>engineer in charge.

od67360/2023_2024 : Supply of single seater sofa made of artificial leather, tufting design element, super soft cushions, high back rest, plush armrest & wood/plywood frame construction.

od67361/2023_2024 : Table (150x75x75 cm) : 1500mm Length x 750mm Depth x 750mm Height,* Table top 25mm thick pre laminated particle board with 2mm edge lipping finish, under structure MS Square leg with powder coated, crossbar square ms tube with powder coated,* Below the table, wire manager raceway frame for electrical & network with powder coated are provided.* Perforated sheet considered as modesty on front.

od67363/2023_2024 : Stool With SS base, 360 degree feet support<br>TUV-CLASS 2 Gas spring: 120mm.<br>Seat upholstered with PU foam

od67365/2023_2024 : CO2 Type Fire extinguisher 4.5kg capacity with ISI mark

STUDIO EQUIPMENTS

od67341/2023_2024 : Supply of High quality studio microphone <br>Ultra-low noise On-mic control with all accessories of standard make as approved by site engineer in charge. Make :( Rode/Focusrite/Audio-Technica/AKG/ equvalent)

od67342/2023_2024 : Supply of Tripod boom microphone stand, for mics at studio with all accessories of standard make as approved by site engineer in charge.<br>Make :( Generic / Equivalent )

od67343/2023_2024 : Supply of Audio Interface, balanced line inputs, suitable for connecting line-level sources, High-performance converters to record and mix with all accessories of standard make as approved by site engineer in charge.<br>Make :( Focusrite/Behringer/Steinberg/equvalent)

od67344/2023_2024 : Supply of Studio Headphones Over Ear Headphones , Studio Sound, Soft Padded with all accessories of standard make as approved by site engineer in charge.<br>Make :( Audio Technica / equivalent)

od67345/2023_2024 : Supply of Amplified studio monitor, Frequency Response. System for high-performance power amplification<br>Room control and high trim response controls with all accessories of standard make as approved by site engineer in charge.<br>Make :( Yamaha/ equivalent)

od67346/2023_2024 : Supply of Workstation with Sound Card- Dell/HP Intel® Xeon® W-2235 Processor. 8.25M Cache, 3.80 GHz, 32 GB DDR2, 512 GB NVMe, + 1 TB SATA with Sound card with all accessories of standard make as approved by site engineer in charge.<br>Make :( Dell/HP/Lenovo/equivalent)

od67347/2023_2024 : Supply of External HDD-1 TB with all accessories of standard make as approved by site engineer in charge.<br>Make :( Seagate/WD/equivalent)

od67348/2023_2024 : Supply of 27" Monitor, 1920 x 1080 Pixels Full HD Monitor - Wall Mountable, Height Adjustable, Panel with HDMI, VGA DP & USB Ports with all accessories of standard make as approved by site engineer in charge.<br>Make :( Dell/HP/Lenovo/equivalent)

od67350/2023_2024 : Supply of High Speed HDMI Cables and adapters with all accessories of standard make as approved by site engineer in charge.<br>Make :( Generic/equivalent)

od67351/2023_2024 : Supply of 22U, 600X600mm Network Rack with PDU Socket, Tray(2 Nos), Cable Organiser 1U Closed, Fan with all accessories of standard make as approved by site engineer in charge.<br>Make :( Generic/equivalent)

od67353/2023_2024 : Supply of Teleprompter Kit for Cameras, Tablet & iPad with all accessories of standard make as approved by site engineer in charge.<br>Make :( Proaim/ selens/ DigioCraft/equivalent )

AIR CONDITIONER

od67340/2023_2024 : Supply & Installation of 1 Ton 3 star inverter type Air conditioner and 4kva stabilizer with all accessories of standard make as approved by the site engineer.<br> Make:(Carrier/ LG/ Samsung/ Blue Star/ Equivalent)

ELECTRICAL

1.17.2 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.2 x 1.5 sq. mm

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.24.1 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.3 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.4 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

90.11.1.18 : Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required

2.3.6 : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator2+6 way, Double door

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.2 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole and netural

2.12.2 : Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.13.2 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.15.3 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

90.10.1.2 : Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )

90.10.1.3 : Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )

90.10.1.5 : Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )

1.10.1 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group A

1.55.3 : Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

od67362/2023_2024 : supply and installation of 1200 mm sweep ceiling fan of standard make as approved by the site engineer in charge (LMR)

od67364/2023_2024 : supplying and fixing DP sheet steel enclosure on surface/ recess complete with connections, testing and commissioning etc. as required. of standard make as approved Make(LMR)

od67366/2023_2024 : Supply and installation of 32 Amps D.P switch

od67367/2023_2024 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required<br>2X 2.5 sq. mm + 1 X 1.5 sq. mm earth wire

od67368/2023_2024 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required<br>2 X 4 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.9 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 6 sq. mm + 2 X 6 sq. mm earth wire

od67369/2023_2024 : Supply and fixing 15 W Round/ Square LED ceiling light with all accessories including cutting false ceiling for, as required and approved by the site engineer,

Ether builders

Lifeline Group of Companies

Bidder Name

Lifeline Group of Companies

Namaste Innovations

Ether builders