Construction of Community Hall at Asufii Punanamei Mao, Senapati District, Manipur.

Amount

Sub-Head 1 :Surface Dressing

Surface dressing of the gruond including removing vegetation and in-equalities not exceeding 15cm deep and disposal of rubbish, lead upto 50m and lift upto 1.5m

Sub-Head 2:Earth Work

Earthwork in eacavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m , including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

Extra for every additional lift of above 1.5 meters or part thereof in All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 metres lift upto 1.5 metre

Supply and filling in plinth with sandy soil under floors including watering, ramming consolidating and dressing complete

Sub-Head 3:Concrete & RCC Work

Providing and Laying in position cement concrete of specified grade excluding the cost of centering & shuttering , 1:4:8 ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Providing and laying in position ready mixed plain concrete or site batched design mix cement concrete for reinforced ccement concrete work, using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland/Portland slag cement, admixture in recommended proportions as per IS:9103 to accelerate/retard setting of concrete, to improve ductility and workability without imparting strength; including pumping of concrete to site laying, curing, carriage for all leads, but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of Engineer-in-charge; for the following grades of concrete: All works upto plinth Level: Concrete of M25 grade with minimum cement content of 330kg/cum

Providing and laying in position ready mixed plain concrete or site batched design mix cement concrete for reinforced ccement concrete work, using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland/Portland slag cement, admixture in recommended proportions as per IS:9103 to accelerate/retard setting of concrete, to improve ductility and workability without imparting strength; including pumping of concrete to site laying, curing, carriage for all leads, but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of Engineer-in-charge; for the following grades of concrete: All works above plinth Level upto floor V Level: Concrete of M25 grade with minimum cement content of 330kg/cum

Reinforced Cement Concrete work in beams, suspended floors, roofs having slope upto 15° landings, belconies, shelves, chajjas, intels, bands, plan window sills, staircases and spiral staircase up to floor five level excluding cost of centering, shuttering, finishing and reinforcement: with 1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone agg. 20 mm nominal size).

Providing and laying damp proof course 50 mm thick with concrete cement 1:2:4(1 cement : 2 course sand : 4 graded stone aggregate 20 mm nominal size)

Applying a coat of residual petroleum bitumen of grade VG-10 of approved quality using 1.7kg per square metre of damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil

Sub-Head 4:Reinforcement Steel/ Rebar work

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically treated bars

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete. Above plinth level.Thermo-Mechanically treated bars

Sub-Head 5:Form work

Centering and shuttering including strutting, propping etc. and removal of form for:

Foundation, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc

Columns, pillars, Piers, Abutments, Posts and Struts.

Suspended floors, roofs, landings, balconies and access platform, with water proof 12mm ply

Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof 12mm ply

Sub-Head 6:Brick work

Brick work with first class common burnt clay F.P.S. (non modular) bricks in foundation and plinth in Cement mortar 1:4 (1 cement: 4 coarse sand)

Half brick masonry with first class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in Cement mortar 1:4 (1 cement: 4 coarse sand)

Sub-Head 7:Wood work

Providing woodwork in frames of doors, windows, celestory windows and other frames wrought, framed and fixed in position with hold fast lugs or with dash fastner of required dia and length (hold fast lugs or with dash fastner shall be pais separately) with Local best quality Teak

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked MS pressed butt hinges bright finished of required sizes with necessary screws with Local best quality Teak wood 35mm thick

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality).

Providing and fixing chromium plated brass night latch including necessary screws etc. complete (Best make of approved quality).

Providing and fixing aluminium Tower bolts ISI marked anodised (anodic coating not less than garde AC 10 as per IS 1868) transparent or dyed to required colour or shade with nuts nad screws etc complete with 250x10mm

Providing and fixing chromium plated Brass handles with necessary screws screws etc.complete.

Providing 40x3mm flat iron hold fast 40cm long I/c fixing to framed with 10 mm dia .bolt nuts and windows plugs and wooden plugs and embedding in cement concrete block 30x10x15mm 1:3:6(1cement:3 coarse sand:6 graded stone aggrt.20mm nominal size)

Sub-Head 8:Finishing work

12 mm thick plaster finished with a floating coat of neat cement of mix 1:3 ( 1 cement : 3 fine sand ) .

15 mm thick plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix 1:3 ( 1 cement : 3 fine sand ) .

Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacture over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with water proofing cement paint of of required shade: New work (two or more coats applied @ 3.84Kg/10sqm)

Painting with oil type wood preservatives of approved brand and manufacture: New work (two or more coats)

Varnishing with varnish of approved brand and manufacture: Two or more coats of glue sizing with copal varnish over an under coat of flatting varnish.

Polishing on wood work with ready made wax polish of approved brand and manufacture: New work

Applying one coat of water thinnable cement primer of approved brand and manufacture: Water thinnable cement primer

Finishing walls with textured exterior paint of required shade: New work (two or more coats applied @ 3.28Lts/1sqm) over and including base coat of water proofing cement paint applied @2.2kg/10sqm.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50grams/litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Sub-Head 9:Flooring work

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete.Size Size of Tile 1000x1000 mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm ( average ) thick base of cement mortar 1 : 4 ( 1 cement: 4 coarse sand ) laid and pointing with cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer -in - Charge. Polished Granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Extra for providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite work.

Providing and fixing 10mm thick acid and/or alkali resistant tiles of approved make and colour using acis and/ or alkali resistant mortar bedding nd joints filled with acid and / or alkali resisting cement as per IS:4457 complete as per direction of Engineer-in-charge. In flooring on a bed of 10mm thick mortar 1:4 (1 acid proof cement: 4 coarse sand) Acid and Alkali resistant tile

Tile work in skirting, riser of steps and dado (upto 2m height) over 12mm thick bed of cement mortar 1:3 (1 cement:3 coarse sand) and jointed with grey cement slurry @ 3.3 kh/sqm including pointing in white cement mixed with pigment of matching shade complete: 8mm thick

Grading roof for water proofing treatment with Cement mortar 1:2:4( 1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size)

Sub-Head 10:Accessesories, Steel and Roofing works

Providing and fixing M.S. grills of required pattern to wooden frames of windows etc. with M.S. flats , square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings/ wooden frames with rawl plugs screws etc.

Providing and Fixing fly proof galvanised M.S. wire gauge to windows and clerastory window using galvanised MS wire guage with average width of aperature 1.4mm in both directions with wire dia.0.63mm all complete; With 2nd class teak wood beading 62x19mm

Providing and fixing 100mm diameter and 60cm long rain water spout in cement mortar 1:4(1 cement: 4 fine sand): Stone ware spout

Providing and fixing on wall face unplasticised-Rigid PVC rain water pipe conforming to IS:13592 Type A including joining with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion, (i) Single sockeded pipes 75mm diameter

Providing and fixing on wall face unplasticised- PVC moulded fittings/accessorie for sunplasticised-Rigid PVC rain water pipe conforming to IS:13592 Type A including joining with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion

Single push fit Coupler:75mm

Single Tee with door:75x75x75mm

Bend 87.5°:75mm bend

Shoe(Plain)

P/F M.S. fan clamps type-I or II of 16mm dia. and M.S.bar bent to shape with hooked ends in RCC slabs, beams during laying including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing in position vertical collapsible steel shutter with vertical channels 20mm x 10mm x 2 mm and braced with flat iron diagonals 20 mm x 5 mm sizes with top and bottom rails of T iron 40 mm x 40 mm x 6 mm with 40 mm dia steel pulleys complete with bolts and nuts, locking arrangements, stoppers handles including applying a priming coat of Steel primer.

Applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works

Painting synthetetic enamel paint of approved brand and manufacture of required colour to give an even shade.Two or more coats on new work.

Steel work in built up tubular (round, square or rectangular tubes etc.) trusses etc., including cutting, hoisting fixing in position and applying a priming coat of approved steel primer, including welding and bolted including special shaped washers etc. complete. Electric resistance or induction butt welded tubes.

Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275gm/sqm

Providing ridges or hips of width 60 cm over all width plain G.S. sheet fixed with polymer coated J. or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete.0.63mm thick with zinc coating not less than 275gm/m2

Sub-Head 11:Extra Architectural Items

Providing and Fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top and bottom pivot & spring type fixing arrangement and making necessary holes etc for fixing required door fittings, all complete as per direction of Engineer-in-charge( Door handle,lock and stopper etc to be paid separately)

Providing and fixing aluminium aluminium tubular handle bar 32mm outer dia, 3.0mm thick & 2100mm long with SS screws etc complete as per direction of Engineer-in-charge. Powder coated minimum thickness 50 micron aluminium tubular handle bar

Filling the gap in between aluminium frame & adjacent RCC/Brick/Stone work by provding weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5mm width.

Sub-Head 12:Ceiling Works

Providing and fitting at all height false ceiling including providing and fixing of frame work made of special sectios, power pressed from MS sheet and galvanised with zinc coating of 120 gmssqm (both sided inclusive) as per IS:277 and consisting of angle cleats of size25mm wide x1.6mm thick with flanges of 27mm and 37mm, at 1200mm centre to centre, one flange fixed to the ceiling with dash fastner 12.5mm diax50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x25x0.55mm of required length with nuts and bolts of required GI channels 45x15x0.9mm running at the spacing of 1200mm c/c, to which the ceiling section 0.5mmthick bottom wedge of 80mm with tappered flanges of 26mm each having clips of 10.5mm at 450mm c/c, shall be fixed in direction perpendicular to GI intermmediate channel with connecting clips made out of 2.64mm diax230mm long GI wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre, with 25mm long drive- all screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c including jointing and finishing to a to a flush finish of tappered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers convering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings and specification and direction of the Engineer-in-charge but excluding the cost of painting with: 12.5mm thick tappered edge gypsum fire resistant board conforming to IS:2095-Part I

Sub-Head 13: Sanitary & Water Supply installation Work

Providing and fixing floor mounted white vitreous china single piece double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolt and gasket etx including making connection with the esixting P/S trap, complete in all respect as per directions of Engineer-in-Charge

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm size respectively with automatic flushing cistern with standard flush pipe and CP brass spreaders with brass unions and GI clamps complete, including painting of ittings and brackets, cutting and making good the walls and floors wherever required: One urinal basin with 5 litre white PVC automatic flushing cistern

Providing and fixing urinal cock of approved quality and colour. 15mm nominal bore, 80mm long, 42mm high and 30mm wide with BSP female threads weighing not less than 48gms

Providing and fixing wash basin with CI brackets, 15mm CP brass pillar taps, 32mm CP brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: White vitreous china wash basin size 630x450mm with a pair of 15mm CP brass pillar taps

Providing and fixing CP brass 32mm size bottle trap of approved quality & make and as per the direction of Engineer-in-charge

Providing and fixing CP brass long nose bib cock of approved quality conforming to IS standard and weighing not less than 810gms. 15mm nominal bore

Providing and fixing CP brass single lever telephonic wall mixer of quality and make as approved by Engineer-in-charge

Providing and fixing 600 x 450 mm levelled edge mirror of Indian make superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with CP brass screws and washers complete

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings arrangement of approved quality and colour, weighing not less than 105gms

Providing and fixing PTMT towel rail complete with bracket fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms

Providing and placing on terrace (at all floor level) polyethylene water storage tank IS:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes without fittings and base support for tank.

Providing and fixing CP brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15mm nominal bore

Sub-Head 14: IEI in Community Hall

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular type switch phenolic laminated sheet suitable size MS-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd.

(a) Group A

(b) Group B

(c) Group B

Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd.

(a) 2X1.5mm2+1X1.5mm2 earth wire

(b) 2X2.5mm2+1X2.5mm2 earth wire

(c) 2X4mm2+1X4mm2 earth wire

(d) 2X10mm2+1X10mm2 earth wire

P/L 25mm2 4 core PVC ins.(heavy duty) Al.cond.armoured cable of 1.1KV grade of size not exceeding 25mm2 but not exceeding 125mm2 direct in ground i/c excavation sand, cushioning protective covering & refilling etc.as reqd.

(a) 5/6 amps switch

(b) 15/16 amps switch

(c) 3 pin 5/6 amps socket outlet

(d) 6 pin 15/16 amps socket outlet

SITC surface mounted LED downlighter with white powder coated Al.housing with intrgrated electronic driver 15 W 840 LHEAAGPIA2W012 complete with connection etc as reqd.(Havell's)

S/F brass batten/angle holder i/c connection etc.as reqd.

S/F 12W LED bulb.

S/F 48"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) blades with regulator etc.as reqd. (Make Bajaj/Usha/Crompton)

S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc.

Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd.

S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd.

SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's)

S/F wall/floor mounted metal board of welded constn.fabricated with minimum 50mm X 50mm X6mm angle iron frame work with horizontal and vertical intermediate members of suitable angle/flat iron for mounting of switch gear i/c painting etc.

Providing & Fixings (following capacity TP & N) dis-connector fuse switch unit inside the existing cubicle panel board with ISI marks HRC fuses including drilling holes in the cubicle panel board, amking connection as reqd. 1. 100 amp. TP & N

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+6 way

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp

Earthing with G.I.earth pipe 4.5mt.long and 40 mm dia. i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.as reqd.

Extra for using salt and charcoal for pipe electrode as reqd.

P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd.

Sub-Head 15: Compound Wall with Gate

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish lead upto 50 cm and lift upto 1.5 metres in Hard/Dense Soil.

Earthwork in eacavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m , including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 metres lift upto 1.5 metre

Providing and Laying in position cement concrete of specified grade excluding the cost of centering & shuttering , 1:4:8 ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Providing and Laying RCC work in position specified grade of reinforced cement concrete, excluding the cost of centering,shuttering,finishing and reinforcement.All work upto plinth level.3.1.1) 1:1:2 (1 cement: 1 coarse sand: 2 graded stone aggregate 20 mm nominal size).

Reinforced Cement Concrete work in beams, suspended floors, roofs having slope upto 15° landings, belconies, shelves, chajjas, intels, bands, plan window sills, staircases and spiral staircase up to floor five level excluding cost of centering, shuttering, finishing and reinforcement in 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in walls (any thickness) i/c attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, abutments, posts, and struts etc. upto floor five level excluding cost of centering, shuttering, finishing and reinforcement in 1:1:2 (1 cement: 1 coarse sand: 2 graded stone aggregate 20 mm nominal size).

Providing and Laying damp proof course 50 mm thick with concrete cement in 1:1.5:3(1 cement : 1.5 course sand : 3 graded stone aggregate 20 mm nominal size)

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically treated bars

Foundation, footings, bases of columns etc. for mass concrete.

Columns, pillars, Piers, Abutments, Posts and Struts.

Suspended floors, roofs, landings, balconies and access platform, with water proof 12mm ply

Half brick masonry with first class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in Cement mortar 1:4 (1 cement: 4 coarse sand)

12 mm thick plaster finished with a floating coat of neat cement of mix 1:3 ( 1 cement : 3 fine sand ) .

Finishing walls with water proofing cement paint of approved quality on new work (two or more coats) to give shade.

Applying one coat of cement primer of approved quality on wall surface.

Finishing walls with weather shield paint of approved quality on new work( three or more coats) to give even shade

Steel work in single sections, i/c cutting, hoisting, fixing in position & applying a priming coat of red lead paint.In M.S. Flat/Plate

Steel work welded in built up sections, framed work in cutting, hoisting, fitting in position & priming coat of red lead paint .In gratings, framed guard bars, ladders, railings, brackets and similar works.

Painting (two or more coats) with anti-corrosive bitumastic paint of approved quality on new work to give an even shade.

Painting (two or more coats) with superior gloss enamel paint of any shade of approved quality on new work to give an even shade.

Sub-Head 16: Land Development

Earth work in excavation/ by mechanical means (Hydraulic Excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as10 sqm on plan) including getting out and disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, as directed by the Engineer-in- Charge.

Sub-Head 17: Fighting & Fire Hydrant

Providing and fixing at approved location approved make 4 nos., for buckets of 24 guage galvanised steel, painted white inside and red outside and black on the bottom, inscribed with letters "FIRE" in black nd gold including stand fabricated out to sheet metal (16 guage) shade, platform and associated civil works, painting etc. as approved by the department.

Providing and fixing carbondioxide fire extinguishers consisting of welded M.S. cylindrical body squeeze lever discharge valve fitted with internal discharge tube, 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket, ISI marked as per IS:2878 finished externally with red enamel paint and fixed to wall with brackets complete with internal charges.Capacity 4.5 kg

D. Pukeho Mao

R.S Daikho