CO Primary Health Center Building at Bagshair Tehsil karsog, Distt. Mandi H.P. SH building portion, water supply and sanitary installation, construction of septic tank and site development.

Amount

Excavation in foundation trenches etc. in earth work in all kinds of soils such as pick work , jumper work, pick jumper blasting work, blasting work in soft and hard rock conglomrate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing out of watering/dewatering upto any lift stacking the excavated soil clear from the edge of excavation and then returning the stacked soil in layers when required into plinth sides of foundations consolidation each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals.

Excavation in drains and channels etc. in earth work in all kinds of soil such as pick work ,jumper work ,blasting work in soft and hard rock conglomerated rock or saturater soil and its intermediate classification of soil ,chisseling work and wedging out rock (where blasting is prohibited)and pumping or balling out watering/dewatering up to any lift including dressing of side ,bed and disposing of exevated earth up to any lead and any lift,deposed earth to be levelled and neatly dressed with in all leads and lifts of material in all respect and as per direction of Engineer-in-charge.

Providing and laying cement concrete 1:6:12 (One cement: Six sand : Twelve graded stone aggregate 40 mm (Forty Millimetre) nominal size and curing complete excluding cost of centring and shuttering in Foundation and plinth including carriage of material within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete and as per HPPWD Specifications of 1990 volume-I including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer-in-Charge.

Providing form work with steel plates 3.15mm (Three point fifteen millimetre) thick welded with angle iron in frame 30x30x5mm (Thirty into thirty into five millimetre) so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling upto all height and removal of the same for insitu-reinforced concrete & plain concrete work including carriage of materials within all leads,lifts and other incidentals as per the direction of Engineer-in-Charge.

Foundation, footings basis of columns etc. and mass concrete.

Columns, pillars, posts and struts Square, rectangular or polygonal in plan.

Beams, cantilever, girders and lintels.Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding in any depth in all heights from floor.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like. Floors etc.upto any thickness.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like.

Stair cases with sloping or stepped soffits excluding landing.

Edges of slabs and breaks in floors and walls: in any wide

Providing and laying cement concrete 1:1.5:3 ( one cement : one point five sand : three graded crushed stone aggregate 20mm (twenty millimetre) nominal size mechanical mixed and vibrated and curing complete excluding cost of form work and reinforcement for feinforced concrete work within including carriage of materials within all leads lifts and other incidentals as per the direction of Engineer-in-Charge.

Foundation, footings basis of columns etc. and mass concrete.

Columns, pillars, posts and struts etc. up to all floor level

Suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers upto all floor level.

Wall (any thickness attached pilasters, buttresses, plinth and string courses etc. from top of foundation level upto any floor level

Stair cases (except spiral stair case) excluding landing but including preparing of the surface and finishing of nosing upto any floor level.

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete upto any floor level including carriage of materials within all leads, lifts and as per HPPWD Specifications of 1990 volume-I

Providing and laying upto any floor level cement concrete 1:2:4 (one cement : two sand : four crushed graded stone aggregate 20mm (twenty millimetre) nominal size and curing complete including form work in string courses coping bed plates, anchor blocks plain window sills and the like including carriage of materials within all leads , lifts and other incidentals as per direction of Engineer-in-Charge.

Providing and laying cement concrete 1:4:8 (One cement: four sand : eight graded stone aggregate 40mm (forty millimetre) nominal size and curing complete excluding cost of form work in: Foundation and plinth including carriage of materials within all leads, lifts and other incidentals or as per direction of Engineer-in-Charge.

Random rubble masonry/polygonal rubble (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement : six sand : twelve graded stone aggregate 20mm (twenty millimetre) nominal size at plinth level in Cement Mortar 1:6 (one cement: six sand) including carriage of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and laying 20 cm (twenty centimetre) thick composit stone masonry with stone facing of chisel dressed stones one line dressed in cement mortar 1:6 (one cement :six sand) and concrete backing with cement concrete 1:3:6 (one cement: three sand: six graded stone aggregate 20 mm (twenty millimetre) nominal size) on inner face of walls including centring, shuttering and propping complete up to all floor level including carrige of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Half brick masonry in common burnt clay building bricks in :- Second Class Bricks in Cement Mortar 1:3 (one cement: three sand) upto any floor level including carrige of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing 2nd class Deodar wood work in frames of dors, windows, clerestory, windows and other frames wrought,framed and fixed in position including carriage of material within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 12 mm (twelve millimetre) thick prelaminated board both side bwp phenol bonded exterior/interior grade panalled shutters with frame of first class Deodar wood for door including bright finished/black enamelled iron butt hinges with necessary screws 40 mm (forty millimetre) thick frame including carrige of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 40 mm (forty millimetre) thick, 2nd class Deodar wood panelled glazed or panelled and glazed shutters for doors windows and clerestory windows.including black enamelled iron butt hinges with necessary screws including carrige of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 40 mm (forty millimetre) thick, 2nd class Deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85G. (eighty five) With wire of dia 0.56mm (zero point fivty six millimetre) for doors, windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws including carrige of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 19mm (nineteen millimetre) thick Commercial Board water proof shutters for cup boards including fixing with nickel plated piano hinges with screws etc. complete including carrige of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 12mm (twelve millimetre) thick 150mm (one hundred fifty millimetre) wide pelmet with 25mm (twenty five millimetre) diametre wooden curtain rods and brackets including fixining 25x3mm (twenty five into three millimetre) M.S. flat 10 cm (ten centimetre) long and plugs etc. complete. In First class Deodar Wood including carrige of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing M.S. plain grills of require pattern in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws including carrige of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 300x16mm (three hundred into sixteen millimetre) anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete including carrige of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing aluminium tower bolts (berrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete including carrige of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

250x10mm (two hundred fifty into ten millimetre)

200x10mm (two hundred into ten millimetre)

150x10mm (one hundred fifty into ten millimetre)

Providing and fixing 125mm (one hundred twenty five millimetre) aluminium handles anodized transparent or dyed to required colour shade with necessary screws etc. complete including carrige of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 150mm (one hundred fifty millimetre) M.S. hooks and eyes including carrige of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 150mm (one hundred fifty millimetre) M.S. single acting spring hinges bright finished with necessary screws etc. complete including carrige of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 150mm (one hundred fifty millimetre) M.S. double acting spring hinges bright finished with necessary screws etc. complete including carrige of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 150mm (one hundred fifty millimetre) M.S. safety hasps and stapples with necessary screws etc. complete including carrige of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 0.60mm (Zero point six zero milimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating to back coat of polyester of 5 microns over 5 microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required as per specifications and as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing ridges or hips 60 cm (Sixty centimeter) overall with 0.60 mm (Zero point sixty millimeter) thick preprinted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat or regular modified polyester organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with screw preprinted iron J or L hooks, bolts & nuts 6mm(Six millimeter) dia and preprinted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing flushing 38cm (Thirty centimeter) overall with 0.60mm ( Zero point six milimetre)thick pre painted sheet in roofing with hot dipped metallic Zink coated sheet with top coat of regular modified polyester organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with screws pre painted J or L hooks, bolts and nuts 6mm(Six milimetre) dia meter & pre painted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-In- charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 15 cm. (Fifteen Centimeter) wide 45 cm (Forty Five Centimeter). overall semicircular plain G.I. sheetgutter with iron brackets 40x3mm ( Forty X Three Millimetre) size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design.(i) 0.63 mm ( Zero Point Sixty Three millimeter) sheet as per the direction of Engineer-In- charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing wind ties of 40mm x 6mm (Forty Millimeter X six Millimeter) flat iron sections as per the direction of Engineer-In- charge including carriage of materials within all leads, lifts and other incidentals.

Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown or / and residual bitumen applied hot at 1.45 kg per square metre of area for each course second course of roofing felt type 3 grade 1 (hessian base self finished bitumen felt) and fourth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cu.dm or 0.006 cum) per sq.m. including preperation of surface excluding grading complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Grading roof for water treatment withCemant concrete 1:2:4 (One cement :Two sand : Four graded stone aggregate 20 mm (Twenty Millimetre) nominal size ) as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing angular fillet 7.5x7.5 cm (Seven Point Five into Seven Point Five ) cement concrete 1:2:4 (One cement :Two sand : Four graded stone aggregate 20 mm (Twenty Millimetre) nominal size ) as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Making khurras 45x45cm (Forty Five into Forty Five ) with average minimum thickness of 5 cm (Five). cement concrete 1:2:4 (One cement :Two sand : Four graded stone aggregate 20 mm (Twenty Millimetre) nominal size finished with 12 mm cement plaster 1:3( one cement three sand ) and coat of neat cement rounding the outlet complete as per direction of Engineer-in-charge including all leads, lifts and carriage of material and other incidental.

Providing and fixing on wall face C.I. accessories for rain water pipes including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1:2 (one cement :two sand) providing and fixing M.S. round holding down bolts with nuts and washers places complete. C.I. Plain bend 100 ( one hundred milimeter) mm dia complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing M.S.holder bat clamps of approved design to C.I. or S.C.I pipes embeded in and including cement concrete blocks 10 x10x10 cm (ten into ten into ten centimetre) of 1:2:4:mix (One cement: two sand ; four graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the wall etc.100 mm ( one hundred vmilimeter) diametre for C.I. pipe complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing on wall face C.I. accessories for rain water pipes including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1:2 (one cement :two sand) providing and fixing M.S. round holding down bolts with nuts and washers places complete. C.I. Plain bend 100 ( one hundred milimeter) mm dia complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing M.S. BP sheet 1.66mm (One point sixty six millimetre) to 2mm (Two millimetre) thick in eaves board/ facia sofits/ ceiling including cutting fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work sheet be measured and paid for separately).

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

In trusses and trussed purlings in buildings.

In gratings framed guard bars,ladders,railling,brackets and similar works.

Precast terrazzo tiles hydraulic compressed 20 mm thick with marble chips of specified sizes laid in floors treads of steps and landings on a bed of 25 mm averagethickness of cement mortar 1:6 (1 cement :6 sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles(wherever required) incliding rubbing and polishing complete with tiles of following shades including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

White shades.

White and grey shades 50% each up to floor all level.

Precast terrazzo tiles 20 mm thick (with marble chips of specified sizes) in skirting and risers of steps not exceeding 30 cm in height on 10 mm thick cement plaster 1:3 (1 cement: 3 sand)jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required)including rubbing and polishing complete with tiles of following shades.:- (i) White and grey 50 % each within all leads and lifts and other incidentals as per the direction of Engineer-in-Charge.

Marble chips skirting or dado upto any height (rubbed and polished to granolithic finish laid in cement marble powder mix 3:1 (three cement : one Marble powder by weight) in proportion of 4:7 ( four cement marble powder mix: seven marble chips by volume) in top layer light shade pigment with white cement (in top layer only) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

White glazed tiles 6 mm thick in skirting risers of steps and dado 12 mm thick cement mortar 1:3 (one cement :three sand) and jointed with cement slurry. including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge

Cement concrete flooring 1:2:4 (one cement : two sand: four graded stone aggregate 20 mm (twenty millimetre) nominal size laid in one layer finished with a floating coat of neat Cement. including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

40 mm ( Forty millimetre) thick up to floor all level

Applying cement slurry on R.C.C. slab or cement concrete work using 2.75 kg (two point seventy five kilogram) of cement per sq.metre of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete. including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and laying marble work (Table rubbed and polished) in flooring on 20mm (twenty millimetre) thick base in cement mortar 1:3 (one cement: threesand) including jointing with cement mortar 1:2 (one white cement: two marble dust) with an admixure of pigment to match the shade of the marble. 20 mm (twenty millimeter) thick White makrana marble. including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

6mm ( six millimeter ) Cement plaster to ceiling In Cement mortar 1:3 (one Cement: three Sand) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

15mm ( Fifteen millimeter) Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth.Cement Mortar 1:6( one cemnet: six sand) up to all floor level including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

15mm ( Fifteen millimeter) Cement plaster in single coat on the fair side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth.Cement Mortar 1:6 (one cement : six sand) up to asll floor level including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing 85 cm (Eighty five Centimeter) high railing with M.S. hollow pipe rectangular pipe 75 x 50 mm (seventy five into fifty millimetre) of 14 gauge baluster M.S. solid square bar 19 x19mm (nineteen into nineteen millimetre) with MS lugs of M.S. flat 40 x 6 mm (forty into six millimetre),10 cm (ten centimetre) long and 2 Nos (two numbers) M.S. plate including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing moulded hand rail of M.S. hollow pipe 50 mm (fifty millimeter) dia welded in straight length over MS flat a tap of vertical baluster 25 mm (twenty five millimetre) dia MS pipe including one coat of red oxide priming coat complete including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge

White washing with lime on undecorated Ceiling and/or sloping roofs two coats to give and even shade including throughly brooming the surface to remove all dirt dust mortar dirt and other foreign matter including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

White washing with lime on undecorated wall surfaces two coats to give and even shade including throughly brooming the surface to remove all dirt dust mortar dirt and other foreign matter including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Distempering with dry distemper of approved brand and manufacture(Two coats)and of required shade on undecorated wall surface to given an even shade over and including primer coat of whiting after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even and sand papered smooth including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Applying priming with cement primer coat on new concrete/masonry/asbestos cement/plastered surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matter and sand papering as required with :- Readymixed primer including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Painting two coats excluding priming on new concrete masonry/plaster surfaces with readymixed paint brushing for use on floors to give an even shade including cleaning the surface of all dirt,dust and other foreign matter and sand papering as required with:--Paint other than white including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matters and scoured with wire brushes fine steel wool scrapers and sand paper with ready mixed priming paint brushing red lead, red oxide/zinc oxide chrome including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Painting two costs (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foregin matters :--Enamel paint other than white including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matters sand papering and knotting.Readymixed paint brushing wood primer pink including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Painting two coats Redy mixed paint other then white (excluding priming coat)on new wood and wood based surfaces,with readymixed paint,brushing to give an even shade including cleaning of all dirt,dust and other foreign matter sand papering and stopping including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

With white paint including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing under layer for plinth protection of 75mm (Seventy Five) thick (unconsolidated) bed dry brick/stone aggregated 40mm (forty millimetre) nominal size with rammed and consolidated and grouted with fine sand including preparation of ground including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge

Providing plinth protection 50mm (Fifty) thick in cement concrete 1:3:6 (one cement : three sand : six graded stone aggregated 20mm (twenty millimeter) nominal size including finishing the top surfaces of concrete smooth including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and laying heavy duty precast cement concrete inter locking paver blocks vibro compacted upto M-50 (fifty) grade including border or kurb block grey of coloured over sub-base of concrete with 25mm ( Twenty Five Millimeter) thick average thickness of cement mortar 1:4 (one cement : four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of block including curing rubbing & polishing complete (sub base concrete floor to be paid for seperaltly 60mm (sixty millimetre) thick block as per direction of Engineer-in-charge including all leads, lifts and carriage of material and other incidental.

Providing and laying 23 cm (twenty three centimetre) half cut stoneware pipes in cement mortar 1:1 (one cement : one sand) complete in all respect including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing to wall ceiling and floor galvanised mild steel tubes (medium grade) tube fitting and clamps including making good the wall, ceiling and floor including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

15 mm (Fifteen millimetre) nominal bore

20 mm (Twenty millimetre) nominal bore

Making connection of galvanised mild steel main 20 mm to 40 mm (twenty millimeter to forty millimeter) nominal bore by providing and fixing tee including cutting and threading the pipes complete including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

providing and fixing PVC water storage tank of ISI:12701 marked,G.I. inlet and outlet connection, 15 mm (fifteen millimeter) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level: 1000 L (one thousand liters) net capacity tank including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing PVC waste water disposal pipe complete in all respects including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

110 mm ( One hundred Ten millimetre) dia

160 mm ( One hundred Sixty millimetre) dia

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc complete including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

110 mm ( One hundred Ten millimetre) dia

150 mm ( One hundred Fifty millimetre) dia

Providing and fixing PVC double equal branch with oval access door, insertion rubber washer 3 mm (three millimeter) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

110 mm ( One hundred Ten millimetre) dia

150 mm ( One hundred Fifty millimetre) dia

Providing and fixing PVC cowl complete in all respects including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

110 mm ( One hundred Ten millimetre) dia

160 mm ( One hundred Sixty millimetre) dia

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc complete 110 mm x 90 mm (one hundred ten into ninety millimeter) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing PVC 'P' or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approve adhesive etc complete 110 mm (one hundred ten millimeter) dia including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing viterous china wash down, water closet squatting pan (indian type W.C. pan) size 580 mm (five hundred eighty millimeter) (earthwork, bed concrete, foot rest and trap to be measured and paid for seperately Orissa pattern including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing 10.00/12.50/15.00 liters (ten point zero/ twelve point fifty/fifteen point zero liters) viterous china low level flushing cistern with a pair of C.I. or mild steel brackets, complete with fiting such as lead valve less syphon, 15 mm (fifteen millimeter) nominal size brass valve withpolythene float, C.P. brass handle, union and couplings for connection with inlet, outlet and overflow pipes, 40 mm (forty millimetre) dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for seperately)

Providing and fixing G.I. inlet connection for flush pipe with W.C. pan including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing viterous china wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings(a) flat back 550 mm x 400 mm (five hundred fiftey millimeter into four hundred millimeter) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing stainless steel kitchen sink of approved standarad ISI make with drain board and C.P. waste with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fitting 610 x 460 mm (six hundred ten into four hundred sixty millimeter) with bowl depth 200 mm (two hundred millimeter) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing C.P. brass waste for wash basin or sink 32 mm (thirty two millimeter) dia including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing M.I. union for wash basin or sink 32 mm (thirty two millimeter) dia including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing 32 mm (thirty two millimeter) dia lead waste pipe for wash basin or sink including brass check nut complete including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing 100 mm (hundred millimeter) sand cast iron grating for gully, floor or nahani trap including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing 600mm x 450 mm ( Six hundred millimetre x Four Hundred Fifty millimetre) bevelled edge mirror of superior glass mounted on 6 mm (Six Millimetre)thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brass screws and washers including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing C.P. brass towel rail complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws 750 mm x 20 mm (seven hundred fifty millimeter into twenty millimeter) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing 600mm x 120 mm (six hundred millimeter into one hundred twenty millimeter) glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. brass screws including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing chromium plated brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing draining board (viterous china) 600 mm x 450 mm ( Six hundred millimetre x Four Hundred Fifty millimetre) dia including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing C.P. brass bib tap with capstan head 15 mm (Fifteen millimetre) dia including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing C.P. brass pillar tap with capstan head 15 mm (Fifteen millimetre) dia including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing C.P. stop cocks 15 mm (Fifteen millimetre) dia including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing C.P. connection pipe with brass unions 45 cm (forty five centimetre) length 15 mm (fifteen millimeter) nominal bore including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing brass full way valve with wheel including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

15 mm (Fifteen millimetre) nominal bore

20 mm (Twenty millimetre) nominal bore

Constructing manhole with R.C.C top slab in 1:2:4 mix in (one cement: two sand: four graded stone aggregate 20 mm (twenty millimeter) nominal size foundation concrete 1:4:8 (one cement : four sand : eight graded stone aggregates) 40 mm (forty millimetre) nominal size) inside plastering 15 mm (fifteen millimeter) thick with cement mortar 1:3 (one cement : three sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix ( one cement : two sand: four graded stone aggregates 20 mm (twenty millimeter) nominal size finished smooth complete including curing and testing including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Inside 800 mm x 800 mm (Eight Hundred millimetre x Eight Hundred millimetre) and 500 mm (five hundred millimeter) deep including C.I. cover with frame light duty single seal pattern - 1) 455 mm x 610 mm ( Four Hundred Fifty five millimetre x Six Hundred ten millimetre) internal dimensions total weight of cover and frame to be not less than 38 Kg (thirty eight kilogram) (weight of cover 23 Kg (twenty three kilogram) and weight of frame 15 kg (fifteen kilogram)

(II) Inside size 1200 mm x 900 mm ( One Thousand Two Hundred millimetre x Nine Hundred millimetre) and 1500 mm (one thousand five hundred millimeter) deep including C.I covr and frame(medium duty) 500 mm (five hundred millimeter)

Brick work using common burnt clay building bricks in foundation and plinth in Cement mortar 1:4 (One Cement : four Sand) second Class Bricks as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .

Cement concrete flooring 1:2:4 (one cement : two sand: four graded stone aggregate 20 mm (twenty millimeter) nominal size laid in one layer finished with a floating coat finished with a floating coat of neat Cement 50 mm (Fifty millimetre) thick up to floor all level including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

15mm (fifteen millimetre) Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor all level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (eighty millimeter) in girth and finished even and smooth. Cement Mortar 1:4 (one cement : four sand) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

supplying and fixing cast iron cover without frame for manhole for frame of 500 mm (five hundred millimeter) internal diameter CI cover (medium duty) the weight of the cover to be not less than 58 Kg (fifty eight kilogram) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Supplying and fixing cast iron cover 300mm X 300mm ( Three Hundred millimetre intoThree Hundred millimetre) with frame for gully trap( standarad pattern) the weight of the cover to be not less than 4.53 kg (four point fifty three kilogram) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Filling in soak pit with broken/ crushed stone Aggregtaes chipping of hard stone of 40 mm (forty millimetre) thick as per PWD specification and as per entire satisfaction and direction of Engineer in Charge including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and laying (two level slopes) and jointing with stif mixtureof cement mortar in proportions of 1:1 (one cement: one sand)salt glazed stoneware pipes grade A of the following internal diameter including testing of pipes and joints complete 100mm ( one hundred milimeter ) diameter including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and laying cement concrete 1:4:8 (one cement: four sand: eight graded stone aggregate 40mm (forty millimetre) nominal size) bedding for stoneware pipes for 100 mm (One Hundred millimetre) internal diameter necessary formwork and curing complete including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Square rubble masonary coursed with hard stone of approved quality in foundation and plinth including rakingout joints in Cement Mortar 1:5 (one cement: five Sand) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Cutting in earth work in all kinds soil such as pick work ,jumper work and blasting work in soft and hard rock saturated soil and its intermideate classification of soil , chieseling /wedging out of rock (where blasting is prohibited )and pumping or bailing out watering/dewatering up to any lift clearance of jungle including uprooting of vegetation ,grass, bushes,wood trees and scrabbling of grith up to any hight and depth ,removal of rubbish and serviceable materials.Any losse to the public and privete property durring the course of execution shall be the absolute responsibility of the contrector.The recovery of 107.62 Cum @ 300/-Per Cubic meter amounting to Rs 32286.00/-only shall be done on prorate basis for the quantity of cutting in earth work effected as per the direction of Engineer-in –charge. Any loss to the public and private property during the course of excavation shall be the absolute responsibility of the contractor, which shall have to be duly compensated by him in all cases.

Providing and laying cement concrete 1:5:10 (one Cement: five Sand: ten stone coursed agreegate)with 15% plum (fifteen percent) and curing complete including the cost of form wit for plain/rainformced in retaining walls, brest walls, the size of the plum be 150 to 300 mm (one fiftey to three hundred) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing weep holes in Brick masonry/ Stone masonry/Plain reinforced concrete. Abutment. R/Wall with 100 mm (One Hundred) dia P.V.C pipe extending through the full with of the structures with of 1(v):20 (H) towards drawing complete as per drawing and technical specification ncluding carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Backfilling behind abutment, wing wall and return wall complete as per drawings and technical specificaiton clause 1204.3.8 as per direction of Engineer-in-Charge including carriage of materials within all leads,lifts and other incidentals.

Gurvaksh Singh