Special repair to Bldg No T-46 and certain sanctioned works at Dholewal Mil Complex under GE Ludhiana

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness ( below or above ground level) complete all as specified and removing rubbish off the premises.

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed by Engineer-In-Charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified and directed by Engineer-In-Charge.

All as per item No 03 above but except bricks etc. Complete all as specified and directed by Engineer-In-Charge (Old brick shall be reused)

Taking down chowkats or frames with shutters not exceeding 1.5 sqm each (without taking off shutters from the frames), complete all as specified and directed by Engineer-In-Charge.

Taking down chowkats or frames with shutters exceeding 1.5 sqm but not exceeding 4 sqm each (without taking off shutters from the frames) complete all as specified and directed by Engineer-In-Charge.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water, etc. Complete all as specified and directed by Engineer-In-Charge and removing rubbish off the premises.

M&L for rendering 12mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6 on walls finished even and smooth without using extra cement complete all as specified and directed by Engineer-In-Charge.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:4 on walls finished even and smooth without using extra cement, complete all as specified and directed by Engineer-In-Charge.

M&L for preparation of new plastered surfaces and applying two coats of cement base paint over plastered surfaces of walls, complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces and distempering walls with two coats of distemper oil emulsion, white or tinted over and including 1mm thick wall care putty including prime coat complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old plastered wall surfaces and applying two coats of Oil bound distemper over a coat of wall care putty ,complete all as specified and directed.

S&F in repair curtain rod made out of 25mm dia(outer dia )pipe having thickness 0.63mm , PVC coated and colour/pattern, over all dia 28 to 29 mm complete all as specified and directed.

S&F in repair plastic finial of 28 to 29mm bore, decorated type, of any colour/pattern, best quality to suit the curtain rod and fixed at the end of curtain rod with suitable adhesive complete all as specified and directed.

M&L One coats of cement base paint including preparation of old plastered surfaces complete all as specified.

S&F in repair mild steel prepainted bracket to hold the curtain rod and fixed to wall(Concrete/brick masonry) with the help of 2 Nos 50mm long steel screws and rawl plug included drilling with electric drill and making good the disturbed surfaces complete all as specified and directed.

Dismantling framed timber scantling 40 sq cm and over in section in any position (framed work) complete all as specified.

S&F Roof truss/Framed works as in purlins, crane grantries, rails and fastening and heavy brackets framing Beam( of tee,angle, pipes of flat section , base plates etc) including distance pieces.

S& F Steel work in tubular /hollow Square pipe trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240,complete all as specified and directed.

S&F steel window & ventilator 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm, 1.25 thick sheet single rebated comprises glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:2:4) type B-1 Four Nos for each window including following fitting welded to frame shutter : (a) Hold fast, 150mm long of 12mm square bar made to shape-04 Nos per window (b) Handles of z section 100mm long (c) Stopper - 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 No per leaf (e) MS Pintal hinges of size 75mm x 75mm x 12mm-02 Nos per leaf (f) Fabrication & fixing arrangement as per drg No CEJZ/TD-7/07 sheet 1/3 to 3/3. Note : Glass and painting shall be measured and paid separately under appropriate item etc complete all as specified and directed by engr-in-charge.

S&F steel window and ventilator 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm, single rebated comprises gauzed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:3:6) type C-1 Four Nos for each window including following fitting welded to frame shutter : (a) Mild Steel Hold fast, 150mm long of 12mm square bar made to shape-04 Nos per window (b) Handles of z section 20mm x 100mm long (c) Stopper - 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 No per leaf (e) MS Pintal hinges of size 75mm x 75mm x 12mm-02 Nos per leaf (f) Grills made out of MS square bar 12mm dia welded to FI frame complete all as specified and shown on drawings. Note : Wire mesh and painting shall be measured and paid separately under appropriate item etc complete all as specified and directed by engr-in-charge.

S&F pressed steel frames,size 125x60mm for doors with one or more rebates pressed out of mild steel sheet of 1.25mm thick including necessary fixing lugs, hinges, lock strike plate etc. complete ,as specified.

All as per item No 22 but Size 105 x 60 mm.

S&F 2nd class hard wood 35mm thick plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed by Engineer-In-Charge. Type of wood : Hollock/SAL or equivalent as approved.

S&F 2nd class HW 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed. Type of wood : Hollock/SAL or equivalent as approved.

M&L for preparation of new wood surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer, complete all as specified and directed by Engineer-in-Charge.

S&F Mild steel pressed handles of size 150mm, oval type, stove enamelled black, complete all as specified and directed by Engineer-In-Charge.

S&F Mild steel barrel tower bolts 200mm long, stove enamelled black, with bright bolt and fixed, complete all as specified and directed by Engineer-In-Charge.

S&F Butt hinges 100mm size, medium weight, cold rolled mild steel, and fixed, complete all as specified and directed by Engineer-In-Charge.

S&F Mild steel sliding door bolts 250mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed by Engineer-In-Charge.

S&F Mild steel 300mm helical door spring, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by engr-in-charge.

S&F 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane, complete all as specified and directed by Engineer-In-Charge.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm, complete all as specified and directed by Engineer-In-Charge.

M&L for providing reinforced cement concrete cast in situ Type B-1, 1:2:4 (20 mm graded stone aggregate) as in lintels upto 1.5m clear span including necessary formwork complete all as specified and directed by engr in charge.(Note : Reinforcement shall be measured and paid separately)

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to complete all as specified and directed by Engineer-In-Charge.

-Ditto- all as per item No 35 above but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binder complete all as specified and directed by Engineer-In-Charge.

M&L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded crushed stone aggregate) as in chajjas, complete all as specified and directed by Engineer-in-Charge. (Reinforcement shall be measured and paid separately)

Formwork to chullah hoods, Chajjas, troughs and similar items including edges fair finished surface complete all as specified and directed by Engineer-in-Charge.

Dismantling asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings including ridges, complete all as specified and directed by Engineer-In-Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed by Engineer-In-Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed by Engineer-In-Charge.

S&F wind tie for roof including securing bolts: flat iron fillets including all necessary drilling, bolting or riveting, etc, and similar work conforming to Fe 410-O or Fe 310-O etc, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint, complete all as specified and directed by Engineer-In-Charge.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed by Engineer-In-Charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thicknness, including cover fillets, complete all as specified and directed by Engineer-In-Charge.

Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre,complete all as specified and directed by engr-in-charge.

Providing and fixing Gypsum Board 8mm thick of size (600x600)mm in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed by engr-in-charge (frame work for ceiling shall be measured and paid separately).

M&L for Machine cut kota stone slab flooring 18-20mm thick over and including 20mm thick cement screed base in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, treating the surface with bees wax polish, complete all as specified and directed by Engineer-In-Charge.

M&L Vitrified ceramic dark shade coloured tiles 8-10mm thick square/rectangular polished area of each tile area not exceeding 0.36 Sqm in skirting over rendering 10mm thick in cement mortar 1:4,Complete all as specified and directed.

M&L for Marble work 18 to 20mm thick (table rubbed and polished) in floor strips,steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of Makrana white,complete all as specified and directed.

M&L PCC 1:2:4 Type B-1 ( 20 mm graded crushed stone aggregate) as in bed blocks, coping, etc. Complete all as specified and directed by Engineer-In-Charge.

M&L for 75mm thick cement concrete type C-2, 1:3:6 (40mm graded crushed stone aggregate) as in plinth protection finished even and fair (without using extra cement), complete all as specified and directed by Engineer-In-Charge.

M&L providing cement concrete type C-0 1:3:6 (12.5 mm graded agg) as for pressed steel chowkhats filling complete all as specified and directed.

M&L for PCC Cement concrete Type D-2, (1:4:8 )mix using 40mm graded stone aggregae as in foundation fillings, mass concrete complete all as specified and directed.

M&L 100mm thick PCC 1:4:8 Type D-2 using 40mm crushed stone aggregate as in sub base floor all as specified.

M&L 80 mm thick interlocking paver block with grey cement and pigment of any size and shape confirming to IS 15658-2006, M-40 Grade as approved by E-I-C laid in flooring and joints filled/broomed with fine sand complete all as specified.

M&L for fine sand filling under interlocking tiles complete all as specified and directed.

M&L preparation of Newly plastered surfaces and applying three coats of White Wash on plastered surfaces of walls etc complete all as specified and directed by Engineer-in-charge.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches in any type of soil not exceeding 1.5m wide and not exceeding 1.5 m depth for foundation & getting out, complete all as specified and directed by Engineer-in-Charge.

M&L for providing cement concrete type D2 1:4:8 (40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

M&L for Brick work with sub class 'B' bricks using old size bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L for filling earth including spreading, leveling, watering and well ramming in layers not exceeding 25cm for soft/loose soil, complete all as specified and directed by Engineer-in-Charge.

M&L Hardcore of broken bricks of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface. Complete all as specified and directed by Engineer-in-Charge.

M&L for sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed by Engineer-in-Charge.

M&L for 40mm thick PCC 1:2:4 type B-1 with 20mm graded crushed stone aggregate as in flooring, finished even and rough to receive the topping layer complete all as specified and directed by Engineer-in-Charge.

M&L for 150mm thick PCC 1:2:4 type B-2 with 40mm graded stone aggregate as in platform for urinal, finished even and rough to receive the topping layer complete all as specified and directed by Engineer-In-Charge.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6 on walls, finished even and smooth without using extra cement, complete all as specified and directed by Engineer-In-Charge.

M&L 5mm thick rendering on concrete surfaces in cement mortar 1:3 , as in ceiling, finsihed the surfaces even and smooth without using extra cement complete all as specified.

M&L for coloured glazed ceramic tiles in vertical surface of size 450x300x7 mm thick laid over and including 10mm thick screed bed in cement mortar 1:4, set and jointed in neat cement slurry and pointed in white or colour cement to match . Complete all as specified and directed by Engineer-in-charge.

M&L three coats white wash on ceiling surfaces inclduing prepration of newly plastere surfaces complte all as specified.

M&L for joint free non-skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engineer-in-charge.

S&F vitreous china under counter top Wash Basin, snow white, oval type of size 560mm x 470mm x 190mm including brackets, cutting for and pinning in ends of brackets or eracting stand & waste pipe, coupling etc complete all as specified and directed by Engineer-in-charge.

S&F vitreous china Urinal, Half stall type, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed by Engineer-in-charge.

S&F urinal spreader of CP any colour for fixing with 15 mm dia pipe complete all as specified and directed.

S&F PVC waste pipe for wash basin, urinal etc complete all as specified and directed by Engineer-in-charge.

S&F vitreous china Urinal partition white of size 310 x 700 complete all as specified and directed by Engineer-in-charge.

M&L granite slab (of any type) 20mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in 15mm thick screed bed of cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite complete all as specified.

S&F 15 mm dia angle stop valve of PTMT any colour pressure screwed for iron pipe and fixed (minimum weight 15mm - 90 gms) complete all as specified and directed by Engineer-In-Charge.

S&F waste coupling dia of discharge pipe 32mm of PTMT (half or full threaded) (Minimum weight 45gms) complete all as specified and directed by Engineer-In-Charge.

S&F grating doom 100mm dia with waste hole of CP complete all as specified and directed by Engineer-In-Charge.

S&F 15mm dia fancy type long body Pillar taps, cast copper alloy with capstan heads Chromium Plated, screwed down high pressure, with or without lettered with long screwed shanks and fly-nuts, screwed for iron pipe but fancy type etc. Complete all as specified and directed by Engineer-In-Charge.

S&F CP soap dish, any type, fixed to plugs with chromium plated brass screws. Complete all as specified and directed by Engineer-In-Charge.

S&F 15mm dia Chromium plated fancy type bib tap cast copper alloy with crutch or butter fly handle screwed down for iron pipe and fixed to 15mm bore pipe complete all as specified and directed by Engineer-In-Charge.

S&F PVC connection 15mm size with PTMT nuts of length 450mm etc. Complete all as specified and directed by Engineer-In-Charge.

S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed by Engineer-In-Charge.

S&F 110mm bore PVC (SWR) bends any radius. Complete all as specified and directed by Engineer-In-Charge.

S&F Steel Tubes Medium Grade Bore of tube 15mm galavanised with all fitting laid in trenches, walls, ceiling or laid in floors etc. Complete all as specified and directed by Engineer-In-Charge.

All as per item No 89 above but of size of 20mm bore. Complete all as specified and directed by Engineer-In-Charge.

S&F rotational moulded polythylene water storage tanks 1000 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified including 20mm dia ball brass valve, complete all as specified and directed by Engineer-In-Charge.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed to steel pipe or union, 20mm bore dia of pipe. Complete all as specified and directed by Engineer-In-Charge.

Supply only 4mm thick figured glass, pinhead type in squares not exceeding 0.5 sqm each pane. Complete all as specified and directed by Engineer-In-Charge.

S&F solid PVC Door Frame of size 50mm x47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube and edges will be painted to match with printed sheets, suppyling & fixing in opening as per specification & drawing. Complete all as specified and directed by Engineer-In-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC sheet ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; & 5mm thick x 15mm wide PVC sheet beading use inside stiles and rails and decorative PVC beading of 10mm x 10mm (90 degree)used. Panelling of wood grain printed PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. Complete all as specified and directed by Engineer-In-Charge.

S&F 100mm size stainless steel butt hinges, medium weight. Complete all as specified and directed by Engineer-In-Charge.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm. Complete all as specified and directed by Engineer-In-Charge.

S&F Aluminium handles, cast type anodised of size 125mm etc complete all as specified and directed.

S&F 150mm long Aluminium anodised, barrel tower bolts of extruded section and fixed, complete all as specified and directed by Engineer-In-Charge.

M&L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed by Engineer-in-Charge.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal/sloping), fair finished surfaces concrete flat, complete all as specified and directed by Engineer-in-Charge.

M&L cleaning the new plastered surfaces with wire brushes, brooms etc and applying a priming coat of bitumen primer @ 0.30 ltrs/Sqm consisting of 3/4 part bitumen of grade 85/25 and 1/4 part of kerosene oil complte all as specified.

M&L providing APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/Sqm ) land on after applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2Kg per Sqm by forced application complete all as specified.

M&L for applying a two coats of water proofing paint with aluminium finish over coat of industrial bitumen 85/25 at the rate of 1.2kg per sqm with forced application above APP based polymeric membrance complete all as specified.

M&L for PCC type B1 (1 : 2 : 4) using 20mm graded crushed stone aggregate as in Manhole coping including necessary form work complete all as specified and directed.

M&L, precast reinforced cement concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in manhole covers and the like set in cement mortar (1:4) duly placed on manholes complete all as specified and directed by Engineer-in-Charge.

M&L for Cement concrete type C2 (1 : 3 : 6) using 40mm graded crushed stone aggregate as in concrete bed to 150mm dia SGSW/RCC drain pipe in any depth including packing under, and haunching against the sides of pipes after they are laid and tested all as specified.

S&F for Reinforced concrete pipes 150 mm bore , class NP3, laid and jointed complete with collars complete all as specified and directed.

M&L for PCC 1:2:4 Type B1 ( 20 mm graded stone aggregate) as in bed blocks, coping, etc. Complete all as specified and directed by Engineer-In-Charge.

M&L Soakage well 1.2 mtr dia x 3.0mtr depth,excavation in ordinary soil, PCC in foundation, Honey combed and soild Bk work in CM (1:4), RCC slab,filling with brick bats complete all as per specified in CEJZ Drg No CEJZ/STD-242/07 Sheet No 9/24 to 12/24.

Surface dressing n.exc 15 Cm deep in soft/loose soil etc complete all as specified and directed by Engr-in-charge.

Excavating over areas, n exc 1.5 m deep and getting out in soft/loose soil complete all as specified.

M&L for hard core of broken stone of bouders n exc 63 mm deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true a surface.

M&L reinforced Cement Concrete type B1 1:1.5:3 (M20) (nominal mix ) (using 20 mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc.Complete all as specified and directed.

Returning ,filling in including spreading, levelling,watering and ramming in layers n. exc 25 cm thick each complete all as specified

Removal of surplus soil to a distance n.exc 50 m & depositing where directed at a level n. exc1.5 m above the starting point copmlete all as specified

Form work to soffits of suspended slab such as roof slab exc 200mm thick (horizontal/sloping/vertical) with fair finished surface complete all as specified

Form work to edges of concrete flats,treads,floors and roofs n. exc 20cm wide and sides of RCC/PCC bands in wall, horizontal or sloping and similar works exc 10 cm but n.exc 20 cm wide complete all as specified

Supply only Integral water proofing compound complete all as specified and as directed by engineer-in-charge.

M&L for hard core of broken stone of bouders n exc 63 mm deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true a surface.

M&L 100mm thick PCC 1:1.5:3 type A1 in flooring , using 20mm graded stone aggregates and finish surface even & smooth using extra cement complete all as specified and directed.

M&L forming grade 'A' construction joints (Dummy) 65mm deep x 10mm wide filled with sealing compound complete all as specified.

Finishing surfaces of concrete roads, pavements, by brooming complete all as specified and directed.

M&L Cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in bed of surface channels and drains all as specified and directed by Engineer – in - Charge.

M&L for cement concrete type B-1, 1:2:4 (20mm graded crushed stone aggregate as in surface channels and drains, complete all as specified and directed by Engr-in-charge.

M&L Extra for forming fair finised drain or channel 30cm inner girth in cement concrete, using extra, including forms, moulds, mitred / stopped ends

M & L Brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6.0m mean radius built in cement mortar 1:4 all as specified and directed by Engineer–in–Charge.

Taking down carefully the point wiring (light, Fan, socket or power) complete, (incl fittings such as switches, sockets any type, ceiling roses, pandents, light fittings, etc for taking credit( credit for above items should be made as per conditions separately) and making good disturbed surface of walls floors etc. all as specified.

Taking down Ceiling fan, sealing cable end, dismantling blades from fan and keeping in safe custody for reuse at site and making good disturbed surfaces complete all as specified and as directed.

Refixing only ceiling fan and connecting up including provision sutiable of new down rod for ceiling fans,of cable from celling rose/ connector to fan all as specified and as directed.

M &L Point wiring complete with 1.5 sqmm single core PVC insulted FRLS cable 1100 volts grade multistranded copper conductor drawn through and including 20mm dia PVC rigid non metallic conduit with all accessories such as internal bend end caps etc complete concealed in walls/ceiling/roof/etc including provision of 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor, all as specified and as directed for the following :-

One light/fan point controlled by one, one way switch

One switch socket outlet point 5 Amps on independent board

One 3 Pin socket outlet , 5 Amps on the same board with other switch

All as per item No. 133 described here-in-before but with copper conductor cable FR LS 2.5 Sqmm for one 3 pin socket outlet, 15 Amps and including provision of 2.5 Sqmm PVC insulated copper conductor cable as earth continuity conductor on independent board

Supply and fix LED tube light fittings 1200 mm, 20W, 240V, 50Hz,rated input current- 0.070-0.110, rated input watt 20, oprating voltage range- 140-270, P.F- not less then 0.95, surge protection upto- 4Kv, IP20, THD shell be less then 10%, CCT- (k0)- 6500ANSI, higher energy saving decorative ultra slim square profile LED lighting fixture with extruded polycarbonate enviromental friendly, energy efficient complete all as specified and directed.

M & L Sub main wiring complete with 2 runs of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade multistranded copper conductor cable with 1 run of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid PVC conduit and conduit accessories concealed in wall/Ceiling etc all as specified and as directed .

Supply and fix TPN MCB DB 4 ways ,Double door with 415 Amps, Double door type complete all as specified and as directed .

Supply and fix MCB TPN 63 Amp, 415 Volt , C- series, 50 Hz, breaking capacity-10 kA complete all as specified and as directed .

Supply and fixing factory made sheet metal enclosures SPN 8 way double door 240 v for DB,s suitable for having MCB flush with wall complete all as specified and directed.

Supply and fixing MCB SPN 40 Amps 240 V, C- curve, 50 Hz, breaking capacity-10 kA. complete all as specified and directed.

Supply and fixing MCB SP 6-32 Amps240 V, C- curve, 50 Hz, breaking capacity-10 kA . complete all as specified and directed

Supply and fix ceiling rose surface type bakelite 65 x 50mm with three terminals complete all as specified and as directed

Supply and Fix Switch Piano,Flush type single pole , one way 5 Amp complete all as specified and as directed.

Supply and Fix Socket outlet 3 pin, 5 A Piano Flush type complete all as specified and as directed.

Supply and Fix Switch Socket combenation 2 in 1 outlet 3 pin, 5 A flush type complete all as specified

Supply and Fix Switch Socket combination 2 in 1 outlet 3 pin, 16 A flush type complete all as specified and as directed.

S&F fan regulator , flush stapped type ,electronic , single phase 230 volt complete all as specified and directed

M &L Earthing work complete with galvanised steel earth plate electrode 60cm X 60 cm X 6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level with the top edge of electrode not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4mm dia means of bolts, nuts,check nuts and washers of galvanised iron and GI lead protected with protection pipe of GI light grade 15mm dia upto 3mtr above ground level along poles fixed with two clamps of 25mm 3mm flat iron and connected to running earth wire at top of poles and watering pipe 20mm bore of GI medium grade all as shown in electrical plate No 3 of SSR Part-I 2009 connected to earthing test point all as specified and direct and testing on completion including PCC 1:3:6 ) C-I cover and frame excavation and earth work etc complete all as specified in elect plate No 3 of SSR Part -I 2009 Note :- PCC Chamber shall be constructed at least 1.50 mtr away from on the earth pit electrode and pipe for watering shall be provided in slanting manner.

Taking down of any size of bldy security light fittings complete all as specified and directed.

Supply and fixing bldg security light fitting LED 30/35 W LED made up of pressure die cast aluminium housing with potted isolated driver and high power LED and indl lenses, oprating range- 90V to 340V AC. , IP66 with high power LED lamp compete all as specified and directed.

S & F for MCB SPN 6- 32 Amps 240Volts, 10kA, C-series, 50Hz 10kA bracking capacity complete all as specified and directed.

Supply and fix for exhaust fan, heavy duty 300mm sweep with louvers, 1400 RPM and connecting up including provision of copper and flexible 3 core of size 0.5 sqmm and PVC connector block complete all as specified. Make :- Crompton/Bajaj/Havells/Philips

Supply, laying and testing cable XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 50 sqmm 3.5 core complete all as specified and directed.

Supplying, filling in trenches, spreading, leveling sand cushioning 8 cm below cable and 15 cm above the cable for under ground cable complete all as specified & directed .

M & L Old size sub class 'B' bricks,laid flat in trenches over the cable with length of brick perpendicular to the direction of the cable , adjacent/abutting each other complete all as specified

Supply, laying and testing cable XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 sqmm 2.0 core Complete all as specified . Make :- Havells/Polycab/Glostar

Supply & fixing for galvanised iron tubes of size 25mm bore (medium grade) with all fittings and laid in trenches, under floor or road including fittings such as socket, bend, elbow, union etc. complete all as specified & directed.

Supply & fixing for galvanised iron tubes of size 20mm bore (medium grade) with all fittings and laid in trenches, under floor or road including fittings such as socket, bend, elbow, union etc. complete all as specified & directed.

Supply & Fix for gun metel gate valve heavy duty ISI marked with iron wheel head screwed both ends for iron pipe 20 mm dia complete all as specified & directed.

Supply & Fix for gun metel gate valve heavy duty ISI marked with iron wheel head screwed both ends for iron pipe 25mm dia complete all as specified & directed.

M &L for cutting the exiting GI 40/25 mm dia taking branch connection 25mm dia including necessary GI fittings/Specials.

AGNIHOTRI CONSTRUCTIONS