improvements to ananthalwar thota, Tirumala

Demolishing and disposal of unserviceable materials within 100 metres lead . Unreinforced cement concrete up to 15cm thickness

Demolition including stacking of serviceable materials and disposal of unserviceable materials within 100 metres lead. RCC work

Demolition including stacking of serviceable materials and disposal of unserviceable materials within 100 metres lead. Brick work.

Dismantling doors, windows and clear storey windows, ventilators etc, (wood or steel) shutters including chowkhats, architraves, hold fasts and other attachments etc., complete and stacking them within 100 metres lead. Not exceeding 3 sq.m in area

Earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all Operational, incidental ,labour charges such as shoring, sheeting, planking, strutting etc., complete for finished item of work. Ordinary soil-Manual means up to 3m depth

Earthwork excavation in hard rock (blasting prohibited) with rock breakers including breaking rock, loading in tippers and disposal with intial lift of 3 m and lead up to 1000 mt, including trimming bottom and side slopes in accordance with with requirements of lines grades and cross sections as per technical specifications clause 302.3.5 MORD/301 MORTH - Mechanical means.

Note: 1 1. The quality, quantity and availability of rock shall be checked before affording credit. 2. In case some rock is issued to the contractor, rate as arrived per cum to that issued extent shall be deducted. 3. In case some rock is issued to the contractor at site , the item carriage shall be restricted / reduced to that extent. 4.Being small quantity, manual loading will be economical in this case and has been provided accordingly.

Note 2: The BoCE committee has resolved to amend the standard data of earth work items such as earth work excavation in all types of soils and rocks and refilling beyond 3.0 M depth, for every 1.0 M depth or part there of, allowance of 10% extra shall be added over the basic rate.

Filling with useful available excavated earth (excluding rock) in trenches, sides of foundations and basement with initial lead in layers not exceeding 15cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T&P etc., complete for finished item of work.

Filling of foundations and basement with best river sand in layers of not more than 15 cms. thick each well watered to saturation and consolidated including cost and conveyance of all materials, incidental charges etc., complete.

Cement Concrete (1:4:8) using 40 mm ( 0.54 cu.m), 20mm (0.27 cu.m) and 12 mm (0.09 cu.m) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cms thick well compacted including curing, machine mixing, cost and conveyance of all materials etc., complete.

Cement Concrete (1:3:6) -Grade M15 using 20 mm ( 0.54 cu.m) and 12 mm (0.36cu.m) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cms thick well compacted including curing, machine mixing, cost and conveyance of all materials etc., complete.

Supply and placing of M 25 Design Mix Concrete corresponding to IS 456 using concrete mixer using of 20 mm HBG crushed metal 0.530 cum (707 kgs),. 10 mm HBG crushed metal, 0.362 cum (471 kgs) , sand 0.407 cum (616 kgs.) and cement 380 kg with water cement ratio of 0.48 ( 182.40 ltrs/ cum of CC) etc., to site and including Seignoirage charges, operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with cement from standard suppliers approved by the department and including hire charges for centering and scaffolding using Steel scaffolding pipes, jack props, wallers, Foot plates, brackets, steel Centering Plates, etc., but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402).

Note : The design mix shall be got designed by furnishing the information required as per clause 19.1.1 & 19.1.2 of IS 456-2000 by the contractor at his own cost and get approved from the competent authority before execution. The cement considered for above M25 grade concrete is 380 kg/Cum and the rate is arrived accordingly in the estimate. After the mix is designed and approved, if there is any variation in the quantity of cement, over the cement content adopted in the estimate, the same will be considered and paid/recovered at estimate rate + or - T.P ( Either increase or decrease in quantity adopted in the estimate). Payment will not be made for variation in the quantity of other materials such as coarse & Fine aggregates.

-do- Columns upto basement level (Pedestals)

-do- Plinth beams

-do- Columns in FF

-do- Lintels in FF

-do- for Rectangular Beams

-do- in First floor

Roof slabs (Excluding centering charges)

-do- in First floor

Hire charges for centering and scaffolding - Unsupported Height upto 3.66m using Steel scaffolding pipes, jack props, steel Centering plates etc, complete.

Roof slabs upto 150 mm thick.- In First floor

RCC M- 20 Design mix using 20mm HBG crushed metal 0.480 cu.m , 10mm HBG crushed metal 0.320 cu.m , sand 0.400 cu.m and cement 350 kg with water cement ratio of 0.53 (185.5 Lit per cu.m of CC ) etc. horizontal plain sunshades or lofts projecting from the face of the wall 65mm average thickness,80mm thick at the face of the wall and 50mm thick at the free end and cast monolithically with the lintels or tailed to the full thickness of the wall where there are no lintels using 20mm size graded machine crushed hard granite metal (coarse aggregate) from any source conforming to the relevant ISI standards including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing , etc.,complete, but excluding cost of centering charges and excluding cost of steel and its fabrication charges for finished item of work.

- do - 0.60 m width

Supply and placing of the M20 Design Mix using of 10mm HBG crushed metal 0.480cu.m,6mm HBG Crushed metal 0.320cu.m,sand 0.400cu.m and cement 350Kgs with water cement ratio of 0.53(185.50 ltrs/cu.m of CC) etc., from any source confirming to the relevant ISI standard including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with minimum cement content as per IS code from standard suppliers approved by the department but excluding cost of steel and its fabrication charges, centering charges, shuttering charges for finished item of work (APSS No. 402)

- do - for 50 mm thick precast slabs using 10 mm graded aggregate HBG crushed metal from any source conforming to the relevant ISI standards with necessary reinforcement, but including cost of necessary form work etc., complete as directed by the department.

-Do- in First floor

Providing High Yield Strength deformed (HYSD)/ Thermo mechancially treated (TMT) steel bars of specified grade (as per IS 1786 - 2008) of different diametres for RCC works, including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars including all wastages such as over laps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc., complete for finished item of work in all floors. (APSS NO.126) (In the absence of 18G binding wire,2 nos of 20G binding wire in tandem are to be strictly adhered). Note: Unless otherwise fabrication and placement of steel, no pre-pament shall be made against the supply of steel reinforcement

- do- Fe500/Fe-500D grade

Construction of Brick Masonry using in CM (1:6) well burnt Bricks 2nd class or ground moulded (Non- modular or traditional size) (230 x 110 x 70 mm)including curing, cost and conveyance of all materials as directed during execution and complying with standard specifications etc., complete.

-Do- in First floor

Construction of 110 mm thick brick partition walls in C.M (1:4) using well burnt Bricks 2nd class or ground moulded ( Non- modular or traditional size) bricks ( 230 x 110 x 70 mm) including curing, cost and conveyance of all materials etc., complete.

-Do- in First Floor

Plastering in Cement mortar using best river sand from approved quarry including cost and conveyance of all materials, screening, curing, rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete for the following proportions.

- do- in C.M( 1:3) 12 mm thick .

-Do- in First Floor

- do- in C.M( 1:5) 12 mm thick .

-Do- in First floor

- do- in C.M( 1:5) 20 mm thick

-Do- in First floor

Flooring with granite slabs set over base coat of cement mortar (1:8) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sqm & jointed neatly with white cement paste mixed with pigment of matching shade to full depth, including cost & conveyance of all materials, seigniorage charges, labour charges for dressing of tiles etc., complete for finished item of work. (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the slabs against supply) telephone Black Granite 18-20 mm thick upto 2.43 M

Flooring with high polished granite 16 to 18 mm thick slabs up to 8'-00 (2.43 M) (other than black and Regular colours) slabs set over base coat of cement mortar (1:8) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sqm & jointed neatly with white cement paste mixed with pigment of matching shade to full depth, including cost & conveyance of all materials, seigniorage charges, labour charges for dressing of tiles etc., complete for finished item of work.

Full Rounding the edges of Marble/ Granite stone slabs of all thicknesses including polishing the same.

Flooring with cement concrete floor tiles of 25 mm thick confirming to IS 1380-12013/IS 1237-2012 of following sizes set over base coat of cement mortar (1:6) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sq.m & jointed with neat cement to full depth mixed with pigment of matching shade including cost & conveyance of all materials, etc., complete for finished item of work. (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the tiles against supply)

Chequered cement concrete heavy duty tiles confirming to IS:13801 using aggregates, cement, pigments of size 300 X 300 x 25mm of any shades.

CUT STONE FLOORING 4" THICK : Supply and dressing with hard granite stone slabs with Three line dressing for flooring from Mulbhagal quarry including cost and conveyance etc., complete with the following specifications. a) The size of the stone slab should not be less than 0.61mx 0.45m (2'-0"x1'-6"). b) The thickness of the stone slabs should not be less than 100mm ( 4") in all sides. c) The top of the slab should be dressed with the following dressings properly. d) All the sides of the slabs should be dressed with following dressing to a depth of 40mm (11/2") from top surface to suit proper alignment and jointing with side slabs. e) The slabs should be laid horizontally and jointed properly to alignment over sand bed (excluding cost of sand bed).cement mortar bed. f) The joint of the slab should not be more than 6mm (1/4" thick). g) The slabs should be jointed with C.M(1:3) and the mortar should not come over the slab for the above item the rate is including cost and conveyance of all materials to site of work including necessary labour charges, dressing, laying, jointing but excluding cost of sand for bed, the bed will be paid under relevant item. (Cement mortar of 0.005 Cum/ Sqm should be used for joints).

Flooring with vitrified tiles of 1st quality of following varieties of series and shades set over base coat of cement mortar (1:6) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kg per sq.m & joints with spacer joints with 3 mm wide jointed neatly with filer material of cement/epoxy grout/white cement paste to full depth mixed with pigment of matching shade as directed during execution, including cost and conveyance of all materials, etc., complete - for finished item of work. (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the tiles against supply)

Supply of Double charged (with double layer pigment) / multi charged stain free full body porcelain vitrified tiles of size 600 x 600 mm and thickness between 8-10 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs

Supplying and fixing in position Flush door shutters, solid bond wood block board type with commercial ply on both faces.: 35 mmthick conforming to IS:2202 of standard make with hot pressed bonded with liquid phenol formaldehyde with rebate cutting, Single leaf using Best Indian Teak wood frames of size 75mm x 100mm without threshold plate, including cost of M.S "Z" Hold fasts of 230 x 50 x 6mm, M.S Powder coated Butt hinges of 125 x 65 x 2.12mm, screws, nails, etc., complete, (excluding cost of other fixtures which will be paid separately but including labour charges for fixing the fixtures).

Supply and fixing of Aluminium hard wares

Supply of Anodised Aluminium Aldrop (IS 2681) -16mm rod 200 mm long. 3T pieces

Supply of Anodised Aluminium tower bolts 10mm dia with 200mm long ISI Mark IS 204 .

Supply of Anodised Aluminium Door handles IS 208 - 12mm rod with 125 mm long

Painting two coats for new wood work with ready mixed Synthetic enamel paint in all shades - Grade-1 over a primary coat with ready mixed wood primer (total three coats) of approved colour and make including brushes to have an even shade including cost and conveyance of all materials as directed during execution complying with standard specifications etc., complete.

Supplying and fixing in position M.S Ornamental grills for windows and ventilators or for verandah openings using M.S. Flats, square rods, angles, sheets etc., of approved design including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the grills with Two coats with Synthetic enamel paint of grade-1 over a Primary coat (Red oxide metal primer) (total three coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforcedwith 1.60 ± 0.2 mm thick galvanized mild steel section made from rollforming process of required length (shape & size according to uPVCprofile), appropriate dimension of uPVC extruded glazing beads anduPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (whitepowder coated) touch locks with hook, zinc alloy body with single nylonrollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mmsize for fixing frame to finished wall and necessary stainless steel screwsetc. Profile of frame & sash shall be mitred cut and fusion welded at allcorners, including drilling of holes for fixing hardware's and drainage ofwater etc. After fixing frame the gap between frame and adjacent finishedwall shall be filled with weather proof silicon sealent over backer rod ofrequired size and of approved quality, all complete as per approved drawing& direction of Engineer-in-Charge inclusive of cost of Single / double glass panes, wire mesh and silicon sealent . Note: For uPVC frame and sash extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted. But no extra payment on this account shall be made.

Three track three panels sliding window with fly proof SS wire mesh(Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and applying wall putty of white cement or polymer or cement based or equivalent putty such as Birla wall care putty of average 1 to 2 mm thickness over plastered surface to prepare the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife / muslin pad, air dry for 2-3 hrs. sand with 180 and 320 No., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work . excluding scaffolding . for internal walls

- Do - for New work.

Painting two coats with Acrylic Emulsion paint interior grade having VOC (Volatile Organic Compound) content less than 50 grams/liter of approved brand over primary coat using ready mixed cement primer (water thinnable) for interior grade-1 (total three coats) and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911 for internal walls.

-Do- for New walls

Painting two coats with Acrylic Exterior Emulsion paint exterior grade with silicon additives having VOC (Volatile Organic Compound) content less than 50 grams/liter of approved brand over one coat of primary coat using cement primer (water thinnable) for exterior grade-II (Total three coats) of approved brand and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911 for external walls.

-Do- for New walls

Conveyance of excavated surplus earth/debris to a distance 2 kms from the site of work at the place specified by the Engineer-in-Charge including loading and unloading etc., complete as directed during execution.

Supplying and fixing in position M.S tubes & pipes of all diameters as per ISI 1161 of approved size design including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the same with Two coats with Synthetic enamel paint over a Primary coat (Red oxide metal primer) (total three coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete.

Supplying, fabrication and fixing of MS base plates of different sizes including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the grills with Two coats with Synthetic enamel paint grade -1 over a Primary coat (Red oxide metal primer (total three coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete

Supply and fixing of Galvalume sheet Pre-painted Galvalume Trapezoidal profile Roofing sheets with 0.47mm thickness, Coating: Alu-Zinc coating AZ150 GSM. Tensile Strength : 550 MPA. Paint coating: regular Modified Polyster painting. Painting Thickness (Top) :18 to 20Microns. (Bottom): 5to7 Microns sheet width:1.020, Length : Maximum 12 Meters with Regular range colours with minimum end lap of 15cms etc., complete including labour charges for erection of Galvalume roof sheet including washers, 'J' bolts etc., complete as directed during execution.

Supply and fixing of roof accessories medium size ridge, barage cap corner trim, L-Flashing, down pipes, gutter etc., with 0.47mm thick, width:0.585, Length maximum 2.50 mts.

Supply and fixing of stain less steel SS 304 grade Tubes, sections, Plates, sheets & pipes of all sizes & diametres etc., including cost and conveyance of all materials and labour charges for fabrication of stainless steel railing works using SS welding rods including buffing, polishing, lacquer finishing, to present seamless finishing etc., complete as directed during execution.

Providing and fixing false ceiling consisting of 600mmX600mm, Solid PVC insulation panels having wall thickness of 1mm thick plain PVC rigid foam sheet and EPS as defined in of desired thickness depending on insulation required shall be insert in a frame work made using anodized aluminium Tee section of sizes 1”X1” (25X25mm, 19 gauge or 1mm thick) in square pattern of grid sizes of 2’X2’ (600X600mm). The aluminium framework is supported from the ceiling with the help of G.I. hook and G.I. wire/6mm.M.S. rods of required sizes to maintain proper level etc. the aluminium framework is supported on side wall with the use of aluminium 1”X1” (25X25mm) angles, complete as per direction of Engineer-in-Charge, manufacture’s specification & drawing

Providing impervious coat to exposed RCC roof slab surface with CM (1:3), 20mm thick with 500 ml of liquid concentrated micronized cement water proof compound/ 100 ml of Integral cement water proofing admixture complies with IS:2645-2003 of approved make per 50 kg bag of cement laid over roof when it is green including cost of all materials, conveyance charges of materials and all operational, incidental and labour charges for mixing mortar, laying, rendering smooth and thread lining, curing, rounding off junctions of wall and slab etc., complete for finished item.

Providing and laying water proofing cum heat insulation treatment with Home Shield Polurethane (PU) Roofkoat (Berger or equivalent) over existing roof slab, all as directed by Engineer-in-charge and as per the following specification:

Surface Preparation

1.Clean the Surface thoughly to make it smooth and free of any foreign material 2.Water pounding test for Mother slab to identify the leakages points before starting the water proofing treatment work 3.Injection grouting should be done for all leakages point indentified and inject the cement slurry dmixed with injection grout admixture, using pressure grouting machine till the rejection of material from the nozzle. 4.Reparing od construction joints by chasing with cutting machine and fill the same with polymerized mortor in C.M91:4) admixture with Advanced Latex plus as per the specified company instructions.

Water proofing Application with PU Roofkoat

1. Apply a self-priming coat of PU Roofkoat after diluting with clean water @50%(1:0.50) 2.Allow to dry for 4 to 6 hours 3.Ally 1st coat of PU roofkoat [email protected] per sqm 3.Allow to dry for 4 to 6 hours 4.Apply 2nd caot of PU roofkiat wuithout dilution @ 0.40Kg per Sqm

The cost inclusive of all required materials such as Home Shield Polurethane (PU) Roofkoat (Berger or equivalent),Injection goruting with required materials, reparing construction joints with required materils and all labour charges for above activities etc., complete as directed during execution.

Electrical items

Supply and Fixing of ISI mark 25mm outer dia heavy grade (2.20mm thickness) with IS:9537 part -3 P.V.C. pipe for concealed wiring in new / existing brick building, walls, columns, beams duly cutting them to the required depth wherever necessary and fixing the pipes and specials with nails and plastering neatly with cement mortar and colour washing to match the finished surface and masonry work for light, fan and separate plug point including all labour charges etc., complete. Makes: Sudhakar / Finolex / Polycab / Kumar / AKG / Indian-tubes / GM / Anchor / Nandi / Polyline / Gold Medal

Supply and Fixing of ISI mark 25mm outer dia heavy grade (2.20mm thickness) with IS:9537 part -3 P.V.C. pipe for concealed wiring in walls of brick building duly cutting them to the required depth wherever necessary and fixing the pipes and specials with nails and plastering neatly with cement mortar and colour washing to match the finished surface and for surface wiring on chromium plated metallic base saddles on ceiling of roof / existing brick building walls, columns, beams, roofs / trusses / channel etc., and masonry work for light, fan and separate plug point including all labour charges etc., complete. Makes: Sudhakar / Finolex / Polycab / Kumar / AKG / Indian-tubes / GM / Anchor / Nandi / Polyline / Gold Medal.

Supply and wiring with 3 run of 14/0.3mm (1.0 sq.mm) PVC insulated FRLS flexible copper cable (ISI MARK) as per IS:694 / 1990 specification in existing PVC pipes / casing & caping with 3 plate Jumbo ceiling rose, 6 Amp 1 Way Module Modular switch to switch control box including all labour charges etc., complete for Light, bell, fan and Exhaust fan points in Non-Residential Buildings. Grade-A: Wire Makes: Finolex / RRKabel / Havells / Polycab / L&T / KEI Grade-A: Modular Switch Makes: Legrand Arteor / Schneider Zen cello / Gold Medal / GIFA / L&T englaze / Crabtree - Murano / Amare / Ducor / GM Four-Five

Supply and wiring with 3 run of 14 / 0.3mm (1.0Sqmm) PVC insulated FRLS flexible copper cable (ISI MARK) as per IS:694 / 1990 specification in existing PVC pipes / casing & caping without ceiling rose, 6 Amp 1 Way Module Modular switch to switch control box including all labour charges etc., complete for Light, bell, fan and Exhaust fan points in Non-Residential Buildings. Grade-A: Makes: Finolex / RRKabel / Havells / Polycab / L&T / KEI Grade-A: Modular Switch Makes: LegrandArteor / Schneider Zen cello / Goldmendal / GIFA / L&T englaze / Crabtree- Murano / Amare / Ducor / GM Four-Five

Supply and run of 3 wire of 36/0.3mm (2.5 Sq mm) PVC insulated flexible FRLS copper cable as per IS:694 / 1990 specification in the existing PVC pipe / MS pipe /PVC Trunking for mains including all labour charges etc., complete. Grade-A: Makes: Finolex / RRKabel / Havells / Polycab / L&T / KEI

Supply and run of 3 wire of 56/0.3mm (4.0 Sq mm) PVC insulated flexible FRLS copper cable as per IS:694 / 1990 specification in the existing PVC pipe / MS pipe /PVC Trunking for mains including all labour charges etc., complete. Grade-A: Makes: Finolex / RRKabel / Havells / Polycab / L&T / KEI

Supply and fixing of 6 /10 Amps 1 way 1 module Modular Switch on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete. Grade-A: Makes: Legrand Arteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree - Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 6 /10 Amps 3 / 2 pin 2 module Modular Socket with shutter on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete. Grade-A: Makes: Legrand Arteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree - Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 16 /20 Amps 1 Way 1 Module Modular Switch on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete. Grade-A: Makes: Legrand Arteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree - Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 20 Amps 2 Module Modular Socket with Shutter on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete. Grade-A: Makes: Legrand Arteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree - Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 6 Modular Cover Plate & Frame on to the Existing Metal Box (Switch control Box) including all labour charges etc., complete. Grade-A: Makes: LegrandArteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree- Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 6 Module Hot Dip Galvanized 20 / 18 SWG Module box with earthing terminal concealed in wall with all required accessories including masonry work and all labour charges etc., complete. Make: Legrand / G.M / L&T / GM Four-Five / Legrand Arteor / Schneider / Anchor / Clipsal / Havells / ABB / Indo Asian / Siemen / Fortune Art.

Supply and fixing of 12 Modular Vertical Cover Plate & Frame on to the Existing Metal Box (Switch control Box) including all labour charges etc., complete. Grade-A: Makes: LegrandArteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree- Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 12 Module Hot Dip Galvanized 20 / 18 SWG Module box with earthing terminal concealed in wall with all required accessories including masonry work and all labour charges etc., complete. Make: Legrand / G.M / L&T / GM Four-Five / Legrand Arteor / Schneider / Anchor / Clipsal / Havells / ABB / Indo Asian / Siemen / Fortune Art.

Fixing of Ceiling fan including transportation and giving connections with twin core wire etc., complete.

Fixing of given (9" to 24") Exhaust fan of in wall with necessary connections and masonry work of making hole, finishing etc., complete

Supply and fixing of 8 way SP & N Distribution board as per IS 8623; IS 13032; IEC 61439-3 with IP-43 protection (Metal door) firmly on the surface of the wall etc., complete. Grade-A: Make: Legrand (Ekinox 3) / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T-Newrang / Indoasian (Opti Pro)

Supply and fixing of 8 Way SP & N Distribution board as per IS 8623; IS 13032; IEC 61439-3 with IP-43 protection (Metal door) firmly concealed in the wall with neat plastering etc., complete. Grade-A: Make: Legrand (Ekinox 3) / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T-Newrang / Indoasian (Opti Pro)

Supply and fixing of 6 to 32 Amps range S.P MCBs 10 KA breaking capacity 'C'/ 'D' Curve ISI Mark as per IS:60898-1:2002 in the existing board and giving necessary connections. Grade-A: Makes: Legrand DX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply and fixing of 40 to 63 Amp SPN/DP MCBs 10 KA breaking capacity 'C'/ 'D' Curve ISI Mark as per IS:60898-1:2002 in the existing board and giving necessary connections. Grade-A: Makes: Legrand DX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply and fixing of 20 Amps 2 Pin & Earth Socket Metal Plug Board with 1 No. 20 Amps SP MCB 10KA 'C' series ISI mark including the cost of MCB on Surface of the wall and giving necessary connections. Grade-A: Make: Legrand (Ekinox 3) / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T-Newrang / Indoasian (Opti Pro)

Supply and fixing of RCCB Up to 40A Double Pole, 30mA for earth leakage protection, confirms to IEC:61008 and IS:12640-1 in the existing boards including internal connections and Labour charges etc., complete. Grade-A: Makes: Legrand DPX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply and fixing of 63A Double Pole, 30mA RCCB for earth leakage protection, confirms to IEC:61008 and IS:12640-1 in the existing boards including internal connections and Labour charges etc., complete. Grade-A: Makes: Legrand DPX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply and transportation of 16 Sq.mm 4 core LT XLPE insulated, 1100V grade armoured Aluminium UG cable as per specification confirming to IS:7098 (Part-I) / 1554-1. Grade-A: Make: Torent / Universal / Unistar / Havells / KEI / Gloster / Polycab / RR Kabel / Finolex.

Laying of U.G cables upto 50 Sq.mm and back filling of trench including labour charges etc., complete.

Supply and making end termination with heavy Alluminium lugs (pin / ring type) upto 16 Sq.mm cable as per IS specification duly crimped with crimping tool, PVC tape etc., complete. Make: Dowels / Jainson / Comet.

Supply and making one end termination with heavy duty single compression brass gland as per BS 6121:2005, IP 66 complete, SIBG type, heavy duty Alluminium lugs duly crimped with crimping tool, PVC tape etc upto 16 Sq.mm with brass washers of Armoured PVC insulated & PVC sheathed / XLPE aluminium conductor cable of 1100 volt grade as required of size. Make: Dowels / Comet / SMI

Earth Work excavation for trench for laying of U.G. Cable in ordinary Soils, manual means to the required width and depth and depositing the same on bank as directed during execution etc., complete .

Supply of 28W, 1200mm BLDC ceiling fan. Sweep : 1200mm (48") Rated Voltage :230V Frequency : 48 - 52Hz Operating Voltage: -140-290V, Single phase AC Power Factor : 0.99 Air Delivery : 230CMM Rated Power : 28W - 30W Motor Speed : 350 RPM with speed control Bearing : Double ball bearing Down Rod size : 260mm Service value : 8.2CMM / W Operating temperature within 2 degree of ambient. Warranty : 3 Years on site Speed control: Regulator compatible conforming as per IS374-2019 latest. makes : TTD approved brands

Supply & fixing of T8 / T5 LED 18W Batten type fitting with lnternal driver with Polycarbonate housing and PC diffuser suitable to operate on 230V AC, 50 Hz power supply as per the following specification. Makes: Philips / Osram / Havells / Crompton Greaves / GE / Orkus.

Technical Specifications: Electrical parameter Specifications: 1. Input Power (W): 18W ±5% 2. Input Voltage (V) : 230V ±5% 3. Power factor : >0.95 4. THD % : <15% 5. Operating Voltage (With load) Vdc : 60 to 80 VDC 6. Output Current (mA) dc : 225 ±5%

7. Driver Efficiency (%) : ≥ 90% 8. Operating Voltage : 140- 270 VAC 9. Operating Frequency (Hz) : 50 ± 3 Hz 10. Output open circuit protection : Yes 11. Output short circuit protection: Yes 12. Surge protection: ≥ 2.5 KV

Optical Specification 1) LED make: NICHIA(Japan)/ OSRAM(German)/ PHILIPS LIMITED/ CREE(USA)/ BRIDGELUX(USA)/ SEOL/ LEDNIM/ EVERLIGHT / LED / EPISTAR / EDISON 2) Luminous Flux (Lumen) : 1800 ±5% 3) Luminous Efficiency (LM/W) : 100 ±5% 4) Colour Temperature (K) : 5500K to 6500K 5) CRI : ≥ 80 6) LED Beam Angle (Degree) : >150 Degree

Environmental: 1) Working Temperature Range: 0 to 40 degree C (Degree centigrade) 2) Working Humidity Range : 0 - 95% Mechanical : 1) IP Grade : IP20 2) Base : NA 3) Housing : PC 4) diffuser : PC Warranty : 5 Years (Rate as per DR.No.127/DE-Elec/TTD/TML//2023-24)

Supply of 12" (300mm) ISI, 900 RPM Heavy duty exhaust fan with metallic blades with Mark. Makes: Crompton / Almounard / Havells Ventil Air-DB

Supply and fixing of fabricated M.S clamps made out of 25mm x 3mm MS flat with necessary holes on either side with 1 1/2" coach screws and painting 2 coats of enamel black paint over one coat of red oxide suitable for fixing of UG Cables of size 10 Sq.mm to 16 Sq.mm on walls etc. including all labour charges etc., complete.

Providing earthing as per IS 3043/ 1987 with 100mm (ID), 13mm thick C.I. Pipe of 3.0 mtr. length after excavating an earth pit of size1.5 m X 0.9 M X 3.00M(Top 1.50 m X 1.20 m X 0.9m & bottom 1.20 M X 1.20 M X 1.65 M) and filling with a homogenous layer of 40 Kgs. of Coke / Char Coal, 20 Kgs. of Salt and the required quantity of sand around 100mm pipe from the bottom of the pipe to a height of 2.7mtr. and filling the remaining excavated portion with earth and consolidation / Settlement of the trench should be done by filling with sufficient quantity of water. A concrete bed of size 0.8 M X 0.8 M X 0.1 M thick and an inspection chamber having inside measurements of 0.4 M X0.4 M X 0.4 M with wall thickness of 100 mm with cement concrete CC (1:2.5:5) using 20 mm HBG Metal is to be constructed with side wall 100 mm above ground level and plastering the exposed walls neatly with CM (1:3) with 12 mm thick

The Top of the Inspection Chamber is to be provided with reinforced precasted RCC Slab with 40mm thick with lifting hook. The top of C.I. Pipe is to be fixed & welded with suitable G.I. Wire mesh funnel 50mm x 6mm G.I. Strip having length of 300mm is to be fixed to the top of C.I. Pipe with G.I. Clamps fabricated with 50 x 3mm G.I. Flats with necessary bolts and nuts and necessary welding to be done to the clamps and C.I. Pipe. 2 Nos. of holes are to be drilled on either side of G.I. Flat for Extending earth connections. 65mm dia PVC Pipe is to be embedded at the pit entry for earth.

After laying earth from earth conductor bus to Electrode trough PVC Pipe, the surface should be covered with bitumen and grease. The cost of GI/Copper flat to be run from CI Pipe electrode to the equipment is to be made separately on running meter basis. The work shall be executed strictly as per IS 3043 - 1987. The rate includes cost and conveyance of all materials, labour charges, incidental charges etc., complete (Note:- Necessary meggaring testing is to be carried out in the presence of concerned Engineers and measurement of resistance shall be as per ISI standards)

Supply and run of ' 8 ' SWG G.I wire for earth electrode to required places by Surface in walls, flooring including cost of all accessories and giving necessary connection with 3/8"x2" GI Bolts, Nuts and Washers wherever joints has to be done. The strip has to be either rivited (or) bolted (or) gas welding neatly and all labour charges etc., complete.

Supply and Transportation of 40W LED Post top lantern made with cast Aluminum with decorative opal polycarbonate diffuser with IP 65 protection etc., complete with all accessories with not less than two years warranty. Makes: Crompton LPTO-40-CDL-M/ Bajaj Celesta BGCL 40 W LED Wh/Wipro LP 02 or equivalent in Phillips/ Keselec/ Havells Endura Spring/Rhino(GPLP14)

Supply and erection of 4 Mts. long 2'' ( 50mm) dia GI pipe 'B' class after excavating an earth pit of size 2'x2'x3' and filled with sand to a height of 6" in the pit and concreting with C.C.1:3:6 with 1 1/2'' (40mm) HBG Crushed metal for full width to a height of 2 ½' over sand bed and coping should be done to a height of 2½' with square / round / hexagonal shape with 20mm HBG Metal in C.C. 1: 3 : 6 and plastering with 12mm thick in C.M. 1: 5. An 155 X 210 X 92 mm Sizes thermo plastic cable junction boxes with IP66/67 weather proof, for outdoor installation with konckouts for cable entry including 1 No. 6 to 32A SP MCB & terminals etc., with screwing / hinges arrangement is to be fixed to the pole above the pole coping with 6mm thick hylum sheet fixed with brass bolts, nuts and washers etc and 2 wire run of 36/0.3mm PVC insulated FRLS copper cable from MS box at bottom to the top of the pipe and giving necessary connections to the fuse unit and to post top lantern fitting etc., The post top lantern fitting is to be fixed on the top of the pipe with suitable GI reducer and GI pipe wherever necessary. Painting should be done with two coats of enamel paint to the GI pipe and to the MS box over one coat of red oxide as directed during execution. (Post top lantern fitting will be supplied by departmentally)

Fixing of M.V / S.V / M.H luminaire / LED/ Halogen fitting on wall / pole cross arm / channel / stem pipe etc., including all labour charges and giving connections etc., complete.

Supply of 3 core 1.5 Sqmm ISI marked, PVC insulated and sheathed FRLS/FRLS-H round copper cable for voltage up to 1100V as per IS 694/1990. Makes: Finolex / RR kabel / Havells/ Finecab /KEI/Polycab/ Gloster/ Goldmedal/GM// Fortune Arrt/Anchor /Million

Supply & fixing of 1" dia 'B' class GI pipe not exceeding 1.5Mtr long with necessary bending (120° to 135°) to the wall or to the pole as directed during execution duly grouting 2 Nos. of MS angle of 35x35x5mm having length 20Cm (grouted portion of MS angles into the wall 7.5cm) and fixing with 2 Nos. of MS clamps fabricated with 25mmx3mm MS flat with suitable holes and 4 Nos. of 3/8"x2" MS bolts, nuts & washers for fixing on the wall / 2 Nos. of suitable MS clamps with bolts, nuts for fixing to the pole etc., complete. A 16Amp fuse unit is to be fixed to the MS angle / clamp and giving necessary connections with 14/0.3mm PVC copper flexible wire from pole to the fuse unit and to the fitting or from Ceiling rose in the building to the fuse unit and to the fitting with link clips etc., and the GI pipe has to be painted with two coats of enamel grey paint over one coat of red oxide paint. Fixing charges for stem pipe including the cost of MS angle, MS clamps, bending of pipe, bolts, nuts, fuse units etc.

Supply and transportation of 45W LED Street light Luminaire made of pressure diecast alluminium body with powder coated, having protective toughned glass, Supply Input voltage 120 - 270 V AC, P.F > 0.90, high power LED's having System efficacy ≥ 120 lm/W and junction temprature < 70°C, with Ingrees protection IP66, Luminaire performance complies to IS 10322 (Part 5 / Sec-3), Driver surge protection 4KV, In house additional Surge protection 10 KV with optics distribution , THD<10% at 110 Volts AC, driver efficiency >90%, CCT: 3000K - 5700K, minimum CRI>70, etc., complete with earth connection and not less than two years warranty

a) LUMINAIRE MAKE : Wipro(Skyline) / Philips (Green line) / GE-Venture / Crompton(Neo Series) / Bajaj (Edge) / Halonix(Lumos - Super) / Havells (Endura Series) /Capart(Premium)/ Greenlites(Hi-Lux) /Polycab/ Keselec/ HPL(City Vision)/ Jaquar(Premium)/ Eveready/ Surya (Pollux) / FortuneArrt (Leaf))/ Rhino ( GPS L04) b) LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG / LG

Supply of 8 Module Plastic surface box Makes: TTD approved brands

Supply and fixing of 8 Modular Horizontal / Vertical Cover Plate & Frame on to the Existing Metal Box (Switch control Box) including all labour charges etc., complete. Grade-A: Makes: LegrandArteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree- Murano - Amare - Ducor / GM Four-Five

Supply of 12 Module Plastic surface box Makes: TTD approved brands

Dismantling of the existing Street / Yard lighting poles / L.T.O.H / H.T.O.H poles with allied accessories (Stem pipe / MS Box / Cross arm / fitting / PVC wire / MS clamp etc.) with out causing any damage to the said materials making site clear by refilling the pit with excavated material and bringing it to the ground level (Note: The dismantled above materials are to be returned to concerned section officer by the contractor at his cost). (Rate as per item No.10.3.10 of Elec SSR 2020-21)

Rupees Seventy Two Lakh(s) Sixty Four Thousand Twenty Nine Only