Construction of Storage Godown and Toilet Block for Transformer Repairing unit at Kamrej sdn Campus under Kadodara Division

Name of work :- Construction of Storage Godown and Toilet Block for Transformer Repairing

unit at Kamrej sdn Campus under Kadodara Division

m Description Qty. Unit Rate Amount

Boring holes 3.5 m deep in ordinary soil (for cast in situ

piles) and getting out the soil and disposal of the surplus

1 excavated soil as directed within a lead of 50 Meter for

following diameter of pipes.(iii) 300 mm

Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and

2 disposing off the excavated stuff upto 50 Meter lead.(B)

Dense or Hard soil

Excavation for foundation for depth from 1.5 m to 3.0 m

including sorting out and stacking of useful materials

3 and disposing off the excavated stuff upto

Meter lead.(B) Dense or Hard soil

Filling available excavated earth (excluding rock) in

trenches. plinth, sides of foundations etc. in layers not

4 exceeding 20 cm. in depth consolidating each

disposited layer by ramming and watering.

Providing, laying, spreading and compacting graded stone

aggregate to wet mix macadam specification including

premixing the Material with water at OMC in mechanical mix

5 plant carriage of mixed Material by tipper to site, laying in 24.00 CMT 1327.00

uniform layers with paver in sub- base / base course on well

prepared surface and compacting with vibratory roller to

achieve the desired density.

Filling in plinth with sand under floors including

6 watering ramming, consolidating and dressing 16.50 CMT 477.03

complete (more than 10 ton)

Filling in foundation and plinth with murrum or selected soil

7 in layers of 20cm. thickness including watering, ramming 100.00 CMT 298.79

and consolidating etc. complete. (upto 10 ton)

Providing and laying cement concrete 1:3:6 (1- Cement : 3-

Coarse sand : 6- Graded brick bat aggregate 40mm normal

8 size) and curing complete excluding cost of formwork in (A)

Foundation and Plinth (upto 10 ton)

Providing and laying controlled cement concrete M.200

and curing complete excluding the cost of formwork

9 and reinforcement for reinforced concrete work in (A) 28.25 CMT 4015.73

Foundations, footings, Base of columns and Mass

Providing and laying controlled cement concrete

M-200 exposed work with curing and finishing

smooth etc. complete including the cost of formwork

10 but excluding the cost of reinforcement for R.C.C 11.00 CMT 8606.80

work in (B) COLUMNS: (ii) Having cross-sectional

area more than 0.18 Sq.M

m Description Qty. Unit Rate Amount

Providing and laying controlled cement concrete

M.200 exposed work with curing etc. complete

including the cost of formwork but excluding the cost

11 of reinforcement for R.C.C. work in (A) BEAMS :(iii) 11.25 CMT 7589.70

Having cross-sectional area more than 0.08 Sq.M

and upto 0.12 Sq.M

Providing TMT Bar FE 500/500D reinforcement for R.C.C.

12 work including bending, binding and placing in position 1950.00 KG 76.52

complete upto floor two level

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

13 and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)

(C) Fly Ash Bricks

Do as Above ….brick work in superstructure above

14 plinth level upto floor two level (C) Fly Ash Bricks 40.00 CMT 4683.00

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for interior

15 plastering upto floor two level and finished even and

smooth in (i) Cement mortar 1:3 (1-cement:3-sand)

Providing 10mm thick cement plaster in single coat on

brick/concrete walls for interior plastering upto floor two

16 level and finished even and smooth in (i)Cement mortar 1:3

(1-cement:3-sand)

17 Finishing with a floating coat of neat cement slurry 303.00 SMT 50.12

20mm thick sand faced cement plaster on walls upto height

10 metres above ground level consisting of 12mm thick

18 backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm 345.00 SMT 312.56

thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc.

Providing cement vata (10cm. x 10 cm. size) quarter round

19 in cement mortar 1:1 including neat cement finishing, 11.00 RMT 24.04

watering etc. complete.

Providing throating or plaster drip and moulding to R.C.C.

Providing & Laying Grenite slab 18 mm thick in skirting,

dedo, risers of steps and landing, sill laid on bed of 10 mm

21 thick base of CM 1:4 finished with flush pointing in white or

colour cement as directed by EIC

22 Labour Charges for Edge Bevelling of Grenite 206.00 RMT 85.00

P & L 24" x 24" vitrified 8 mm thick tile flooring over

mm (average) base of cement mortar 1:6 ( 1 cement:

coarse sand) on new surface or fixing on existing

23 flooring by adhesive material including dismentaling of 55.00 SMT 1456.96

existing flooring and jointed with color cement slurry

including finised with flush pointing & cleaning the

surface etc. complete for light shed

Providing and laying polished Kota stone slab flooring

over 20mm (Average) thick base of cement mortar 1:6

(1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty

24 :1.5 - coarse sand) laid over and jointed with grey 161.00 SMT 1005.48

cement slurry mixed with pigment to match the shade

of slab including rubbing and polishing etc. complete.

m Description Qty. Unit Rate Amount

Providing and laying marble stone slab flooring over 20mm

(average)base of cement mortar 1:6 (1-cement : 6 coarse

25 sand) or L.M. 1:1.5(1- lime putty : 1.5 - coarse sand) laid 72.00 SMT 2173.03

and jointed with gray cement slurry including rubbing and

polishing complete. (A) Marble slab 25mm thick

Providing and applying Primer coat and Wall painting (three

coats) with plastic emulsion paint of approved brand and

manufacture on undecorated wall surface to give an even

26 shade including throughly brushing the surface free from 356.00 SMT 142.02

mortar droppings and other foreign matter and sand

papered smooth.

Applying two coats of Birla (white cement based) or Asian

(acrylic lapy- putty) or equivalent & two coats of primer of

approved brand and manufacture on new wall surface to

27 give an even shade including thoroughly brushing the 356.00 SMT 40.19

surface free from mortar dropping and other foreign matter

and sand papered smooth.

Providing and applying Primer coat and Finishing wall with

weather proof exterior emulsion paint on wall surface (two

28 coats) to give an required shape even shade after 395.00 SMT 135.43

thoroughly brushing the surface to remove all dirt, and

remains of loose powdered materials.etc complete

Providing and fixing extruded aluminum window,

Door, etc having extruded aluminum Colour Powder

Coated section frame main outer size 127mm x

38.10mm x 1.35mm (of Jindal Section no:2443,@

Wt.1.384 Kg/mt),horizontal Four track member size

122.20mm x 31.75mm x 1.10mm (of Jindal Section

no:8787,@ Wt. 1.205 Kg/mt),vertical member of size

122.20mm x 31.75mm x 1.50mm (of Jindal Section

no:8935,@ Wt. 1.398 Kg/mt) with sliding shutters of

29 horizontal member size 40mm x 18mm x 1.29mm 8.00 SMT 2119.14

(of Jindal Section no:8949 @ wt.of

0.456Kg/mt),vertical member of size 40mm x 18mm

x 1.29mm (of Jindal Section no:8947 @ wt.of

0.456Kg/mt/Section 8948,@ Wt. 0.457 Kg/mt) with

mm thick transparent bronze colour tinted float glass

with powder coated aluminum fittings and fixtures

and transparent silicon sealant glass fixing to frame

as per details etc complete for window.

Providing and fixing 35 mm thick shutters for Doors,

windows and clerestory windows including Indian teak wood

frames 10 cm x 7 cm. size including anodized alluminium

30 fixtures and fastenings including primer coat of approved 2.50 SMT 5285.45

quality and two coats of oil painting etc, complete. (ii) Fully

Providing and fixing FRP frame size 125x65 mm and

35mm thick FRP shutter with wood grain raised

panneled design finish shutter having extra

reinforcement on sides & edges in Gel coat finish.

The core of the shutter & frame is to be filed up with

injected polyurethene foam done in situ alongwith

31 embedded wooden pieces for stiffening & also taking 7.25 SMT 1999.98

hinges & fintures. The whole FRP frame & shutter is

to be water proof weather proof, termite proof &

resistance to mild acid/alkali. Rates are to be

inclusive of S.S hinges with fastener sleeve &

alluminium fixtures & fastenings.

m Description Qty. Unit Rate Amount

CONCEALED DOOR CLOSER (GODREJ/DORMA / HAFELE)

ITS 96 - Providing and fixing Concealed Door Closer Dorma

ITS 96 EN -2-4 Cam action door closure /approved

equivalent suitable for max width of 1400 mm or approved

equivalent make. The door closer shall be with integrated in

the frame or door leaf, with rapidly decreasing opening

32 resistance. Closing sped and latching action adjustable; 3.00 NO 2035.00

mechanically cushioned limit stay. Adaptation to different

rebate clearances possible non-handled (i.e. suitable for

right hand & left hand door); max.opening angle

degree. All complete as per detail drawing, as specified and

as directed by Architect / Consultant / Project - In - Charge.

Providing and fixing M.S. grills of required pattern to

wooden frames of windows etc. with M.S. flats at required

33 spacings and frame alround, square or round bars with 170.00 KG 161.41

round headed bolts and nuts or by screws. (B)

ORNAMENTAL GRILL

Providing and fixing of Ridge flashing for roof panel shall be

made out of 0.5 mm thick pre coated GI sheet . The

Precoated sheet shall be of minimum 240 mpa steel grade

confirming to IS 14246:1995 and shall have zinc coating of

minimum 120 gsm as per IS:277:1992 , 5-7 microns epoxy

primer on both side of the sheet and polyester top coat 15-

18 micron. The PPGI Sheet shall have plastic protective

34 guard film of minimum 25 microns to avoid scratches 201.00 SMT 858.80

during transportation. The ridge shall be fixed to the steel

members by pop rivet or self drilling/self stitching fastners

@ maximum 450 mm c/c along length of capping/flashing

etc complete . (Note - for payment the measurement of

area shall be that of actual net area of sheet fixed.)

Providing and fixing of Ridge flashing for roof panel

shall be made out of 0.5 mm thick pre coated GI sheet

. The Precoated sheet shall be of minimum 240 mpa

steel grade confirming to IS 14246:1995 and shall have

zinc coating of minimum 120 gsm as per IS:277:1992

5-7 microns epoxy primer on both side of the sheet

35 and polyester top coat 15-18 micron. The PPGI Sheet 30.00 RMT 515.28

shall have plastic protective guard film of minimum

microns to avoid scratches during transportation. The

ridge shall be fixed to the steel members by pop rivet

or self drilling/self stitching fastners @ maximum

mm c/c along length of capping/flashing etc complete .

Steel work, welded in built up sections framed work

including cutting, hoisting, fixing in position and applying a

priming coat of red lead paint. (A)In beams and joists,

36 channels angles Tees, flats, with connecting plates or angle 4025.00 KG 90.18

cleats as in main and cross beams. Hip and jack rafters,

purlins conneted to common rafters and the like

m Description Qty. Unit Rate Amount

Providing laying and jointing in true line and level 50mm

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings

make PRINCE / SUPREME / ASTRAL / FINOLEX or

equivalent as approved by Engineer In Charge. Pipe shall be

37 fixed on the wall with the help of clamp at every two metre 15.00 RMT 193.73

C/C or shall be concelled as directed including necessary

fittings etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of all

Providing laying and jointing in true line and level 40mm

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings

make PRINCE / SUPREME / ASTRAL / FINOLEX or

equivalent as approved by Engineer In Charge. Pipe shall be

38 fixed on the wall with the help of clamp at every two metre 25.00 RMT 146.65

C/C or shall be concelled as directed including necessary

fittings etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of all

Providing laying and jointing in true line and level 25mm

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or

equivalent as approved by Engineer In Charge. Pipe shall

39 be fixed on the wall with the help of clamp at every two 20.00 RMT 90.93

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost of

Providing laying and jointing in true line and level 15mm

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or

equivalent as approved by Engineer In Charge. Pipe shall

40 be fixed on the wall with the help of clamp at every two 25.00 RMT 71.93

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost of

Providing and fixing Gun metal check or non-return fullway

wheel valve.(C) 25mm dia.

Providing and fixing Gun metal check or non-return fullway

wheel valve.(E) 40mm dia.

Providing and fixing Two way BIB cock with wall flange of

genuine Jaquar ompany brand, in with model no FUS-

43 CHR29041, water tap brand or approved ISI brand quality, 6.00 NO 2300.00

fixing in pieline and testing the same… etc., complete., as

directed by EIC

Providing and fixing brass screw down stop tap.(A)

Providing and fixing chromium plated brass half trun

45 flush cock of approved quality including fixing in pipe 2.00 NO 261.16

line etc. complete.(ii) 25mm dia.

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside

46 Dia. Low densidy, complete with special falnge compression 10.00 RMT 190.12

type fittings, wall clipsetc. including making good the wall

ceiling and floor. (E) 50mm

m Description Qty. Unit Rate Amount

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure polythene pipes of the following outside

47 Dia. Low densidy, complete with special falnge compression 15.00 RMT 277.46

type fittings, wall clipsetc. including making good the wall

ceiling and floor. (F) 75mm

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside

48 Dia. Low densidy, complete with special falnge compression 25.00 RMT 335.69

type fittings, wall clipsetc. including making good the wall

ceiling and floor. (G)110 mm

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside

49 Dia. Low densidy, complete with special falnge compression 15.00 RMT 510.17

type fittings, wall clipsetc. including making good the wall

ceiling and floor.160 mm

Providing and fixing PVC SWR Nahni trap IS 14735 for drain

- 75 mm diameter with jali of the following nominal

50 diameter of self cleansing design with C.I scread down or 2.00 NO 580.47

hinged grating including the cost of cutting and making

good the walls.

Constructing brick masonry chamber for underground C.I.

Inspection chamber and bends with briocks having croshing

strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with

frame (Light duty) 455mm x 610mm intenal dimensions

total weight of cover with frame to be not less than 38Kg.

(Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top

51 slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded 2.00 NO 2903.89

stone aggregate 20mm size) foundation concrete 1:5:10

inside plaster 15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls and

bed concrete etc. complete.(i) Inside dimensions 455mmx

610mm and 450mm deep for pipe lines with three or more

Providing and fixing C.I. Manhole cover with frame 0.60 M.

x 0.45M. size having weight not less than 35Kg.

Providing and fixing S.W. gully trap with C.I. grating brick

masonry chamber and water tight C.I. cover with frame of

300mm x 300mm size (inside) with standard weight.(i)

Square mouth traps.(B) 150mm x 100mm size P or R type

Providing and fixing washbasin with single hole for pillar tap

with C.I. or M.S. brackets painted white including sutting

54 holes and making good the same but excluding fittings.(A) 2.00 NO 3960.55

Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm

size. (i) In white colour.

Angle Cock with PVC pipe connection upto WHB

Providing & fixing pillar taps of approved quality(Jaquar cat

no 5309) with capstan head screw down high screws,

shanks & back nuts. (ii) 15mm dia.

m Description Qty. Unit Rate Amount

57 Hose pipe for pillar cock 2.00 NO 234.60

Providing, fixing,testing & commissioning of White

Vitereous China Floor mounting / Wall Mounted type

European Water Closet / Orissapan with C.P. bolts, nuts,

C.I. chair (painted with two coat of enamel paint over

58 a coat of primer) or other hanging arrangement, built 2.00 NO 6941.30

in concealed low volume compatiable cistern with C.P.

bolts, nuts supporting arrangements, bakelite

/polypropylene seat & cover with C.P. hinges & rubber

buffers, complete with all accesories. Including cutting &

making good the walls & floor whereever required.

W.C. pan with ISI marked white solid plastic seat and lid

59 Jet spray heavy duty with S.S. Braided hose 100 cm long 2.00 NO 305.93

60 Concealed cock 15 mm Heavy duty with cap 2.00 NO 486.44

Concealed Flush Valve with all connecting pipes for WC

Providing and fixing white vitreous china flat back half

stall urinal of size 580x380x350 mm with white PVC

automatic flushing cistern, with fittings, standard size C.P.

brass flush pipe, spreaders with unions and clamps (all in

62 C.P. brass) with waste fitting as per IS : 2556, C.I. 2.00 NO 10128.00

trap with outlet grating and other couplings in

C.P. brass,including painting of fittings and cutting and

making good the walls and floors wherever required : Single

half stall urinal with 5 litre P.V.C. automatic

flushing cistern

Providing and fixing in position cowel went to pipes.(C)

Providing and fixing 600mm x 450mm bevelled edge mirrror

of superior glass mounted on 6mm thick A.C. sheet or

plywood sheet and fixing to wooden pluge with C.P. brass

screws and washers.

Providing and fixing C.P. brass towel rail comlete with C.P.

65 brass brackets fixed to wooden plugs with C.P. brass scews. 2.00 NO 610.32

(B) 600mm x 20mm size.

Providing and fixing Toilet paper holder (A) C.P brass

Providing and fixing PTMT soap dish holder having

length of 138mm, breadth 102mm, height of 75mm

with concealed fitting arrangements.

Providing erecting and fixing double coated ISI water tank

68 of required capacity each with all necessary fittings and 2000.00 Lit 3.91

connection etc. complete on terrace

69 PVC 4kg 90 mm dia rain water pipe 120.00 RMT 125.00

m Description Qty. Unit Rate Amount

Miscellaneous expense for unforseen work which shall be

70 paid as per SOR Rate. Rate for Non SOR item shall be paid 1.00 JOB 25000.00

at approved rate analysed by EE Civil & DE Civil.

Total Amount Excluding GST

Total Amount Excluding GST

"All royalties, toll tax, local tax, development charges, and any other taxes etc., in respect of this contract and also any

statutory variation in future towards above mentioned taxes & any other taxes if levied in future by statutory authority

applicable to the this contract shall be payable by the con-tractor and DGVCL will not entertain any claim whatsoever in

The Contractor has to pay 1% Labour Welfare Cess of estimated cost to the concern Government Department.

The contractor shall produce the receipt of payment of 1% welfare cess from the respective govt. department before

submission of final bill, otherwise final bill for the works will not be finalized.

The proof of payment made by the contractor to the appropriate department shall be submitted to DGVCL, failing

which appropriate amount shall be withheld on getting information/instruction from the concerned department.

I /We agree to carry out the above work at

Add (+)________% above . Rs.

Less (-) _________% below Rs.

Total cost of work. Rs.

(Total cost of work Rs. ______________________________

Signature of Tendered CEO & SE (O&M)

Seal of company DGVCL,Circle Office Surat-R