REPAIR TO WOODEN STEEL FURNITURES AND REWEAVING RETAPPING CANNING OF FURNITURE AT MIL STATION GANDHINAGAR

Amount

Repairs to Charpoy GI 32mm ply top (Drg No FD-220R)

(a) Removing unserviceable ply top and S&F new plywood top of size 1980mmx900mmx12mm thick BWR grade ISI Marked . Plywood top shall be fitted with appropriate sizes of nuts and bolts with washer all as specified and shown on drawings and as directed.

(b) Removing of damaged/broken long rail from charpoy GI pipe and S&F new long rail made out of GI Pipe 32mm bore (ISI marked) medium grade including threading both sides all as specified in Drg & directed.

(c) Removing of old damaged/broken short rail from Charpoy and making of short rail from old u/s long rail (retervied from ser item No 1.02 above) including threading & fixing in charpoy GI Pipe all as specified in Drg & directed.

(d) Removing of old damaged/broken leg from charpoy and making leg from old u/s short rail (retervied from ser item No 1.02 &1.03 above) including threading & fixing in charpoy GI Pipe all as specified in Drg & directed.

(e) Removing of old broken/damaged check nuts and S&F new check nuts of 32 mm dia heavy duty to Charpoy GI pipe all as specified in Drg & directed.

(f) Removing old broken/damaged GI elbow, 3 way, 32 mm bore and S&F new GI elbow, 3 way, 32mm bore (ISI marked) to Charpoy GI pipe all as specified in Drg & directed.

(g) Removing damage/broken welded suports from charpoy GI Pipe 32mm and S/F new support made out of 40 x 6 mm flat iron, 850 mm long duly welded to charpoy including applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified in Drawing and directed.

Repair to Charpoy IP folding (FD-388 & FD 388(R))

(a) Removing of old unserviceable charpoy top and S & F new top of 8-9mm thick plywood BWR grade (ISI Marked ) with appropriate size nuts,bolts & washer including thightening the loose components complete all as specified in drg and directed.

(b) Removing of old unserviceable members of charpoy folding and S & F new members of 25 mm dia 2 mm thck MS condute fixed with gas welding as specified & shown in drg.

(c) M & L for preparation of old painted steel surfaces by scraping/rubbing with sand paper and filling depressions with putty where ever required and applying one coat of synthetic enamel paint of approved shade complete all as specified in drg and directed.

Repair to Chorpoy IP Hard top FD/MAP-II/01

(a) Removing of old unserviceable ply wood from charpoy and S&F new 12 mm thick plywood, BWR grade, (ISI Marked) to the top of charpoy IP of appropriate size including fixing to charpoy using nuts, bolts and washers as shown on drg complete all as specified in drg and directed.

(b) M & L for preparation of old painted steel surfaces by scraping/rubbing with sand paper and filling depressions with putty where ever required and applying one coat of synthetic enamel paint of approved shade complete all as specified in and directed.

Repair to Chair Dining CB, Chair Writing, Chair easy, Bin soiled linen (Drg Nos FD-203, 226, 353, 354, 280, 250, 229 17(M) & 244)

Re-caning of Chairs, Bin Soiled Linen etc (except Chair Verandah) with 2mm wide & 0.4mm thick half round plastic cane except border which shall be 3.5mm(Minimum) wide & 0.6mm thick, flat superior quality cream/ white colour and weaving in accordance to Godrej Pattern as shown on drawing including removing unserviceable plastic cane all as specified and directed.

Repair to Chair Verandah (Drg No FD-19(M), FD-256, FD-359 & FD/E6/MAP-II/06

(a) Re-caning of Chair Verandah with 4mm wide & 0.4mm thick half round plastic cane except border which shall be 5mm wide & 0.6mm thick flat super quality cream/ white colour including applying one coat of synthetic enamel paint White after preparation of surface to complete frame of chair all as specified and directed.

(b) Repairs to broken mild steel components of chair verandah with gas welding all as specified and directed.

(c) Removing old broken leg of chair verandah and providing new 20mm dia MS pipe 1.6mm thick complete with welding all as specified and directed.

(d) Removing old broken PVC seat & back of chair verandah and S & F new PVC seat & back 4 mm thick as specified and directed.

(e) S&F, PVC rubber Shoe/Toe of best quality for the legs of chairs after removing the old un- serviceable shoes all as specified and directed.

Repair to table dining ORs Steel Alluminium top (Drg No FD-165)

(a) Removing existing unserviceable table top and S&F, new table top made from block board, grade 2 quality, interior grade, commercial type, 19mm thick, size 1910x 680mm (ISI Marked) duly covered with anodised aluminum sheet 22 gauge thick and fixed with screws to MS pipe frame all as shown in drawing and directed.

(b) M&L for gas welding to broken joints/spots of 25mm x 25mm square pipe frame all around all as specified and directed.

(c) Cutting of worn out/damaged legs of table and replaced with new MS square pipe piece 3" to 4" long including welding complete.

(d) M&L for painting to MS frame of table dining with one coat of black synthetic enamel paint including preparation of surfaces complete all as specified and as directed.

(e) Removing unserviceable hard rubber shoe from legs of table and S&F, new hard rubber shoes as per existing size complete.

Repairs to Almirah Large Steel (Drg No FD-67(M) &1031) FD/MAP/18

(a) M&L for one coat of synthetic enamal paint OG to internal /external surface & shelves completely after preparation of old painted surfaces by applying sand paper and filling with putty where ever required to Almirah Large steel all as specified & directed .

(b) Removing of old broken/unserviceabble shelves from Almirah large steel and S&F new shelves made out of 1mm thick MS sheet bent to shape required all as specified in drg & directed .

(c) Removing broken/ dacayed legs from exsiting Almirah Large steel and S&F new legs made out 1.00 mm thick MS sheet bend to shape all as specified in drg and directed.

(d) Removing of old unserviceable locking device three way from exsiting Almirah Large steel and S&F new locking device made out of 10 mm dia MS bar round and 3 mm MS plate all as specified in drg and directed .

(e) Removing of broken/unserviceable handle from existing almirah large and S&F new Chromium Plated steel handle 100mm long all as specified in drg & directed.

(f) Removing of old unserviceable lock from exsiting almirah Large (Drg No FD-67(M), 1031 & FD/MAP/18 ) and S&F new four lever lock with duplicate keys all as specified in drg & directed .

(g) Removing of old/broken cleats from existing Almirah largesteel with shelves (Drg No FD-67(M), 1031 & 1032) and S&F new cleats made out of 1.6 mm thick PBI sheet bend to shape and shall be fixed with nut & bolt to give support to shelves all as specified in drg & directed.

Repair to Almirah Med Steel (Drg No FD-1032)

(a) M&L for one coat of synthetic enamal paint OG to internal/external surface & shelves completely after preparation of old painted surfaces by applying sand paper and filling with putty where ever required to Almirah Medium steel all as specified & directed .

(b) Removing of old broken/ unserviceabble shelves from Almirah Medium steel and S&F new shelves made out of 1mm thick MS sheet bent to shape required all as specified in drg & directed .

(c) Removing broken/ dacayed legs from exsiting Almirah medium steel and S&F new legs made out 1.00 mm thick MS sheet bend to shape all as specified in drg and directed .

(d) Removing of old unserviceable locking device three way from exsiting Almirah Medium steel and S&F new locking device made out of 10 mm dia MS bar round and 3 mm MS plate all as specified in drg and directed.

(e) Removing of broken/unserviceable handle from existing almirah large/medium and S&F new Chromium Plated steel handle 100mm long all as specified in drg & directed.

(f) Removing of old unserviceable lock from exsiting almirah Large/Med steel (Drg No FD-67(M), 1031 & 1032) and S&F new four lever lock with duplicate keys all as specified in drg & directed .

(g) Removing of old/broken cleats from existing Almirah large/medium steel with shelves (Drg No FD-67(M), 1031 & 1032) and S&F new cleats made out of 1.6 mm thick PBI sheet bend to shape and shall be fixed with nut & bolt to give support to shelves all as specified in drg & directed.

Repairs to Teapoy Varandah (Drg No FD-35(M), FD- 295, D-255, FD-383)

(a) M&L for spot welding to broken joints of MS member of teapoy verandah all as specified and directed

(b) Removing old u/s tops from Teapoy varandah and S&F new top made out of 18mm thick pre-laminated particle board exterior grade type II (ISI marked) both side white with teak wood beading all around all as specified in drg & as directed .

(c) M&L for one coat of synthetic enamal white paint to Teapoy Varandah after preparation of old painted surfaces by applying sand paper and filling with putty where ever required all as specified & directed .

Repair to Chair tub steel with or withhout Arms (Drg No 75(M)

(a) M&L for gas welding to broken members of chair tubular steel, with & without arms all as directed

(b) M&L for painting of MS frame of chair tubular steel with arms with one coat of olive green synthetic enamel paint all as specified and directed.

(c) M&L fot painting of MS frame of chair tubular steel without arms with one coat of olive green synthetic enamel paint all as specified and directed.

(d) Dismantling of unserviceable seat of chair tubular steel with arms and without arms, S&F new seat made out of Ist class hard wood frame of size 18"x16" and 18"x18", fixing to chair with 75 x 6mm GI nut and bolt, including canning with 2mm plastic cane white half round and 4 mm plastic cane for border all as per drawing .

(e) Dismantling to unserviceable back of chair tubular steel with arms and without arms, S&F of new back made out of Ist class hard wood frame of size 16"x16" and 18"x15", fixing to chair with 75 x6mm GI nut & bolt, including canning with 2mm plastic cane white half round and 4 mm plastic cane for border all as per drawing .

(f) S&F of plastic cap 19mm dia to plug the open end of pipe of chair as shown in drawing .

(g) Dismantling of unserviceable hand rest and S&F new hand rest made out of Ist class hard wood duly painted with black colour complete all as shown in drawing and directed

Repairs to Table Office Clerk Steel (Drg No FD-84(M) & 1004)

(a) M&L for one coat of synthetic enamal paint OG to all steel Surface after preparation of old painted surfaces by applying sand paper and filling with putty where ever required to Table office clerk steel all as specified & directed.

(b) Removing of unserviceable drawers from existing table office clerk steel and S&F, new drawers made out 1 mm thick MS sheet all as specified in drg & directed.

(c) Removing old u/s tops from Table office clerk steel and S&F new top made out of 18mm thick pre-laminated particle board exterior grade type II (ISI marked) one side teak face & other side white with 4mm thick teak wood beading all around, all as specified in drg & as directed.

(d) Removing of old unserviceable lock from exsiting table office clk steel and S&F new four lever lock with duplicate keys all as specified .

Repair to Table Office Officer Steel (Drg No FD-84(M) & 1003)

(a) M&L for one coat of synthetic enamal paint OG to all steel Surface after preparation of old painted surfaces by applying sand paper and filling with putty where ever required to Table office Officer steel all as specified & directed.

(b) Removing of unserviceable drawers from existing table office Officer steel and S&F new drawers made out 1 mm thick MS sheet all as specified in drg & directed.

(c) Removing old u/s tops from Table office Officer steel and S&F new top made out of 18mm thick pre-laminated particle board exterior grade type II (ISI marked) one side teak face & other side white with 4 mm thick teak wood beading all around, all as specified in drg & as directed .

(d) Removing of old unserviceable lock from exsiting table office Officer steel and S&F new four lever lock with duplicate keys all as specified.

(e) M&L for gas welding to broken joints of table office Officer/Clerk steel all as specified and directed.

Repair to table 900x600x760mm with drawer/without drawer steel (Drg No FD-1008 & 1007)

(a) Taking down unserviceable table top and S&F new top of 18 mm thick prelaminated particle board, interior grade, solid core with melamine face on one side and balancing white on other side including 4 mm thick teak wood edging all around complete all as shown on drawing.

(b) M&L for gas welding to broken joints of table Steel all as specified .

(c) Removing of unserviceable locks of drawer and supply & fixing new four lever locks with key in duplicate all as specified in drawing.

(d) Repairs to the drawer of table steel by making good dents, proper alignment for smooth function of drawer and preparation of old surfaces, inside and outside of drawer and legs & applying one coat of olive green paint by spray painting all as specified and directed.

Repairs to Bed Hard Steel FD/E6/MAP/8(R)

M&L for removal of u/s ply wood of bed and S&F new ply wood 12 mm thick, BWR grade, ISI marked including fixing with suitable size screw & cup washer complete all as shown on drg and specified.

M&L for retightening of loose components of bed including welding where ever required on joints, replacement of old nuts & bolts where ever required and touching up on welded points with synthetic enamel paint of same colour/ shade all as shown on Drg & directed .

M&L for removal of prelaminated particle board Headrest of bed , and S&F new 18 mm thick prelaminated particle board exterior grade mellamine faced veneered both side decorated(ISI Marked) with 4 mm thick teak wood beading of suitable size including fixing in position with screws & washers, complete all as shown on drg and directed.

M&L for removal of prelaminated particle board footrest of bed , and S&F new 18 mm thick prelaminated particle board exterior grade mellamine faced veneered both side decorated (ISI Marked) with 4 mm thick teak wood beading of suitable size including fixing in position with screws & washers, complete all as shown on drg and directed.

Repair to Chair Dinning (Drg No. FD-203, 226, 228, 279, 353 & 354) FD/E6/MAP-II/05

(a) M&L for removing of old broken rear leg of chair dinning and S&F new rear leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(b) M&L for removing of old broken front leg of chair dinning and S&F new front leg made out of first class hard wood (teak wood) of similar size & shape complete as specified & shown in drg.

(c) M&L for removing of old broken stifner of chair dinning and S&F new stifner made out of first class hard wood (teak wood) of similar size & shape complete as specified & shown in drg.

(d) M&L for removing of old broken front/side/rear rail of chair dinning and S&F new front/side/rear rail made out of first class hard wood (teak wood) of similar size & shape including drilling holes for caning all as specified & shown in drg.

(e) M&L for removing of old broken back rest of chair dinning and S&F new back rest made out of first class hard wood (teak wood) of similar size & shape all as specified & shown in drg.

(f) M&L for removing of old unserviceable PVC seat of chair and S&F new PVC seat of 4mm thick and fixing with suitable screws all as specified and directed.

(g) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of chair dining all as specified and directed.

Repair to Chair Easy (Drg No. FD-229, 17M, 201)

(a) M&L for removing of old broken rear leg of chair easy and S&F new rear leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(b) M&L for removing of old broken front leg of chair easy and S&F new front leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(c) M&L for removing of old broken front/side/rear rail of chair easy and S&F new front/side/rear rail made out of first class hard wood (teak wood) of similar size & shape including drilling holes for caning all as specified & shown in drg.

(d) M&L for removing of old broken top/bottom/side rail of back rest of chair easy and S&F new top/bottom/side rail made out of first class hard wood (teak wood) of similar size & shape including drilling holes for caning all as specified & shown in drg.

(e) M&L for removing of old broken arms of chair easy and S&F new arm made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(f) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of chair easy all as specified and directed.

Repair to Chair Writing CB (Drg No. FD-280, 20M, 202, 250)

(a) M&L for removing of old broken rear leg of chair writing and S&F new rear leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(b) M&L for removing of old broken front leg of chair writing and S&F new front leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(c) M&L for removing of old broken stifner of chair writing and S&F new stifner made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(d) M&L for removing of old broken front/side/rear rail of chair writing and S&F new front/side/rear rail made out of first class hard wood (teak wood) of similar size & shape including drilling holes for caning all as specified & shown in drg.

(e) M&L for removing of old broken arms of chair writing and S&F new arm made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(f) M&L for removing of old broken back rest of chair writing and S&F new back rest made out of first class hard wood (teak wood) of similar size & shape all as specified & shown in drg

(g) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of chair writting all as specified and directed.

Repair to Chair writing with cushion seat & back (Drg No FD/E6/MAP/12 )

(a) Taking out old/unserviceable seat and S&F new seat made of 120 mm thick hot pressed ply wood upholstered with fabric and mouled polyurethane foam with PVC lipping all round. The polyurethane foam shall be 50mm thick and 5shall be moulded with density 50-55 KG per Cum complete all as shown on drg.

(b) All as item No 19.01 above but old/unserviceable back complete all as shown on drg & as directed..

(c) Taking out old broken/unserviceable arm rest of chair writing and S&F new one piece arm rest made of black integral skin polyurethane with 75-85 Shore 'A' hardness and reinforced with MS insert, it shall be scratch and weather resistant all as shown on drg.

(d) Prepration of old painted surface by scraping , rubbing & applying one coat of synthetic enamel paint (black) to MS tubular frame of chair writing complete all as specified and directed.

(e)Taking out unserviceable/brokan frame and S&F new frame cantilever type powder coated MS tubular frame made of 25mmx10mm all as per drg complete all as directed .

Repair to Chair School with hand board ( Drg No FD/E6/MAP/05 )

S&F in replacement of Hand board of 18 mm thick prelaminated particle board exterior grade mellamine faced veneered both side decorated (ISI Marked), including 4mm thick teak wood beading all round, fixed to frame with suitable 12 Nos nuts, bolts & washer complete all as specified on drg and directed.

S&F in replacement of polypropelene (Seat & Back) set complete all as specified and directed.

S&F in replacement of hard rubber/PVC shoe/ring of superior quality with suitable screw complete all as specified and directed.

Repairs to Teapoy Wooden (Drg No. FD-382, 232, 34M, 278)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(c) M&L for removing of old unservicable front/rear rails, and S&F, new teak wood rail duly finished/smoothened complete all as specified & shown in drg.

(d) M&L for removing of old unservicable bottom rails and S&F, new teak wood rail duly finished/smoothened complete all as specified & shown in drg.

(e) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of teapoy all as specified and directed.

Repair to table 900x600x760mm with or without drawer (Drg No FD-41,42(M) & 224, FD-228,279,16(M),203,55,223 & 284)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(c) M&L for removing of old unservicable long rail and S&F, new teak wood long rail duly finished/smoothened complete all as specified & shown in drg.

(d) M&L for removing of old unservicable short rail and S&F, new teak wood short rail duly finished/smoothened complete all as specified & shown in drg.

(e) M&L for removing of old unservicable middle stiffener and S&F, new teak wood middle stiffener duly finished/smoothened complete all as specified & shown in drg.

(f) M&L for removing of old unservicable side stiffener and S&F, new teak wood side stiffener duly finished/smoothened complete all as specified & shown in drg.

(g) M&L for removing of old unservicable drawer and S&F, new drawer made out of Ist class hard wood and 6mm thick ply wood for bottom of drawer complete all as specified & shown in drg.

(h) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table all as specified and directed.

Repair to Sofa Set (Drg No FD-281, FD-373

(a) M&L for removing old unservicable arms of sofa set single or 3 seat and S&F, new arms of sofa set single or 3 seat made out of 1st class hard wood (Teak wood) of size and pattern all as shown on drawing.

(b) M&L for removing old unservicable leg of sofa set single or 3 seat and S&F, new leg of sofa set single or 3 seat made out of 1st class hard wood (Teak wood) of size and pattern all as shown on drawing.

(c) M&L for removing old unservicable cushion of sofa set and S&F, new cushion of 100mm thick foam, 40 density, size 530mm x 500mm for seat and back of Sofa Set 4/5 Seater, covered with superior quality tapestry cloth including stitching in size etc complete all as shown on drawing and as directed.

M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of sofa set 4 seater all as specified and directed.

M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of sofa set 5 seater all as specified and directed.

Repairs to Table writing (Drg No. FD-33, FD-249 & FD- 275)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for removing old unservicable front side of drawer and S&F, new front side of drawer made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side including providing new chromium plated 35mm size knob complete all as specified and shown on drawing.

(c) M&L for removing old unservicable bottom of drawer and S&F, new bottom of drawer made out of 6mm thick, commercial ply wood complete all as specified and shown on drawing.

(d) M&L for removing old unservicable door and S&F, new door made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround including fixing with hinges and providing new chromium plated 35mm size knob all as specified & shown in drg.

(e) M&L for removing old unservicable back of table writing and S&F, new back of table writing made out of 6mm thick, commercial, BWR grade ply wood complete all as specified and shown on drawing.

(f) M&L for removing old unservicable side of table writing and S&F, new side of table writing made out of 6mm thick, commercial, BWR grade ply wood complete all as specified and shown on drawing.

(g) M&L for removing old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified and shown in drg.

(h) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table writing all as specified and directed.

Repairs to Table 900 x 900 x 760 mm (Drg No. FD-88M, 288 & 291)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for removing of old unservicable rails and S&F, new teak wood rail duly finished/smoothened complete all as specified & shown in drg.

(c) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(d) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table all as specified and directed.

Repair to table dining 6 pers (Drg No 273 & FD/MAP-II/03)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for removing of old unservicable long rails and S&F, new teak wood long rail duly finished/smoothened complete all as specified & shown in drg.

(c) M&L for removing of old unservicable top side rails and S&F, new teak wood top side rail duly finished/smoothened complete all as specified & shown in drg.

(d) M&L for removing of old unservicable top side short rails and S&F, new teak wood top side short rail duly finished/smoothened complete all as specified & shown in drg.

(e) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(f) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table all as specified and directed.

Repair to side board (Drg No FD-26,241,371 & 372)

(a) M&L for removing old unservicable double leaf door and S&F, new double leaf door made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side including providing new butt hinges and new chromium plated 35mm size knob complete all as specified and shown on drawing.

(b) M&L for removing old unservicable front side of drawer and S&F, new front side of drawer made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side including providing new chromium plated 35mm size knob complete all as specified and shown on drawing.

(c) M&L for removing old unservicable bottom of drawer and S&F, new bottom of drawer made out of 6mm thick, commercial ply wood complete all as specified and shown on drawing.

(d) M&L for removing of old unservicable side & rear rails and S&F, new teak wood side & rear rail duly finished/smoothened complete all as specified & shown in drg.

(e) M&L for removing old unservicable back of side board and S&F, new back of side board made out of 6mm thick, commercial, BWR grade ply wood complete all as specified and shown on drawing.

(f) M&L for removing old unservicable top of side board and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side complete all as specified & shown in drg.

(g) M&L for removing old unservicable side of side board and S&F, new back of side of side board made out of 6mm thick, commercial, BWR grade ply wood complete all as specified and shown on drawing.

(h) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(j) M&L for removing of old unservicable chromium plated knob of side board and S&F, new chromium plated knob all as specified & shown in drg.

(k) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of side board all as specified and directed.

Repair to Peg table (Drg No. FD-266, FD-277, FD-384, 25M)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(c) M&L for removing of old unservicable front & rear rail and S&F, new leg made out of 1st class hard wood teak duly finished/ smoothened complete all as specified & shown in drg.

(d) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of peg table all as specified and directed.

Repairs to Bin soiled linen (Drg No. FD-70(M) & 244)

(a) M&L for removing old unservicable back, top & front of bin soiled linen and S&F, new back, top & front of bin soiled linen made out of 6mm thick, commercial, BWR grade ply wood complete all as specified and shown on drawing.

(b) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(c) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of bin soiled linen all as specified and directed.

Repait to Table Centre (Drg No. FD-235 & 274)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(c) M&L for removing of old unservicable top long rails and S&F, new teak wood top long rail duly finished/smoothened complete all as specified & shown in drg.

(d) M&L for removing of old unservicable top short rails and S&F, new teak wood top short rail duly finished/smoothened complete all as specified & shown in drg.

(e) M&L for removing of old unservicable side stiffener and S&F, new teak wood side stiffener duly finished/smoothened complete all as specified & shown in drg.

(f) M&L for removing of old unservicable middle stiffener and S&F, new teak wood middle stiffener duly finished/smoothened complete all as specified & shown in drg.

(g) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of center table all as specified and directed.

Repair to Table dressing ladies with mirror Drg No FD-235,274 & FD/MAP-II/07)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side complete all as specified & shown in drg.

(b) M&L for removing old unservicable back of table and S&F, new back of table made out of 12mm thick, commercial, BWR grade ply wood complete all as specified and shown on drawing.

(c) M&L for removing old unservicable side and partition and S&F, new side and partition made out of prelaminated particle board 12mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side complete all as specified & shown in drg.

(d) M&L for removing old unservicable bottom ply wood of drawers of table and S&F, new bottom ply wood of drawers of table made out of 6mm thick, commercial, BWR grade ply wood complete all as specified and shown on drawing.

(e) M&L for removing old looking mirror of table and S&F, new looking mirror of 5.5mm thick with teak wood frame and with 6mm thick, commercial, BWR grade ply wood at back complete all as specified and shown on drawing.

(f) M&L for removing old unservicable aluminum channel and S&F, new aluminum channel having two 'U' shaped channels for sliding of plain glass of 5mm thick complete all as specified & shown in drg.

(g) M&L for removing old unservicable/broken sliding glass shutter and S&F, new plain, sliding glass, 5mm thick shutter complete all as specified and as shown in drawing .

(h) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table dressing ladies all as specified and directed.

Repair to Table dressing Gents with mirror (Drg No. FD-230,31M & FD/MAP/16)

(a) M&L for removing old unservicable back side of the box of table and S&F, new back side of the box of table made out of 12mm thick, teak wood planks in one piece, complete all as specified and shown on drawing.

(b) M&L for removing old unservicable top of the box of table and S&F, new top of the box of table made out of prelaminated particle board 12mm thick exterior grade (ISI marked), with one side teak face and balancing white on other side complete all as specified & shown in drg.

(c) M&L for removing old unservicable bottom of the box of table and S&F, new bottom of the box of table made out of prelaminated particle board 12mm thick exterior grade (ISI marked), with one side teak face and balancing white on other side complete all as specified & shown in drg.

(d) M&L for removing old unservicable side and partition and S&F, new side and partition made out of prelaminated particle board 12mm thick exterior grade (ISI marked), with one side teak face and balancing white on other side complete all as specified & shown in drg.

(e) M&L for removing old looking mirror of table and S&F, new looking mirror of 5.5mm thick with teak wood frame and with 6mm thick, commercial, BWR grade ply wood at back complete all as specified and shown on drawing.

(f) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table dressing gents all as specified and directed.

Repair to Table bed side (Drg No. FD-276)

(a) M&L for removing old unservicable ply wood of back side of Table bed side and S&F, ply wood of back side of Table bed side made out of 6mm thick, commercial, BWR grade ply wood complete all as specified and shown on drawing.

(b) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(c) M&L for removing old unservicable top of table bed side and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side complete all as specified & shown in drg.

(d) M&L for removing old unservicable Shelf of table bed side and S&F, new Shelf of table bed side made out of prelaminated particle board 12mm thick exterior grade (ISI marked), with one side teak face and balancing white on other side complete all as specified & shown in drg.

(e) M&L for removing old unservicable side of table bed side and S&F, new side of table bed side made out of prelaminated particle board 12mm thick exterior grade (ISI marked), with one side teak face and balancing white on other side complete all as specified & shown in drg.

(f) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table bed side all as specified and directed.

Repair to Table bed side (Drg No. FD/E6/MAP/15(R)

(a) M&L for removing damage/broken MS square pipe and S&F, new MS 18mm size square pipe of 18 Gauge thick, length n.exc 600mm each part for various parts of table bed side duly painted with two coat of synthetic emnamel paint ( approved colour) over a coat of red oxide primer all as shown on drg & as directed.

(b) M&L for removing damage/broken handles of draweras and S&F new handles for drawer 75mm long mild steel chromium plated all as per drg & as directed

(c) M&L for removing damage/broken sides and S&F new sides with 18 mm thick Pre lamineted particle board exterior grade mellamine faced veneered both side decorated (ISI Marked), all as per drawing & as directed.

(d) M&L for removing damage/broken top and S&F new top with 18 mm thick Pre lamineted particle board exterior grade mellamine faced veneered both side decorative (ISI Marked) with 4 mm teak wood edging with polished all as per drg & directed.

(e) M&L for removing damage/broken draweras and S&F new drawer all as per drg & directed.

(f) M&L for removing damage/broken shoe and S&F new PVC/Rubber shoe all as per drg & directed.

Repair to Hat stand with mirror (Drg No. FD-23M, 223 & 361)

(a) M&L for removing old looking mirror and S&F, new looking mirror of 5.5mm thick with teak wood frame and with 6mm thick, commercial, BWR grade ply wood at back complete all as specified and shown on drawing.

(b) M&L for removing broken aluminium hook and S&F, new aluminium hook, solid body, 125mm for Hat Stand complete all as specified and shown in drawing.

(c) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of Hat Stand Small all as specified and directed.

Repair to Almirah mess utensil (Drg No. FD-93(M)

(a) M&L for removing of old broken top and S&F new top of 1065x455x19mm size block board covered with 1mm thick laminated sheet complete all as specified & shown in drg.

(b) M&L for removing of old broken shelf and S&F new shelf of 1025x420x19mm thick planks of 1st class hard wood (Teak) complete all as specified & shown in drg.

(c) M&L for removing of old broken shelf and S&F new shelf of 1025x270x19mm thick planks of 1st class hard wood (Teak) complete all as specified & shown in drg.

(d) M&L for removing old unservicable back ply and S&F, new back of ply of size 1065x1570mm made out of 10mm thick, commercial, BWR grade ply wood complete all as specified and shown on drawing.

(e) M&L for removing of old broken shutter and S&F new shutter of 19mm thick block board covered with 1mm thick laminated sheet complete fixed with new hinges all as specified & shown in drg.

(f) M&L for removing of old aluminum handle and S&F new aluminum handle of 100mm long complete all as specified & shown in drg.

(g) M&L for removing of old hasp and staple and S&F new aluminum hasp and staple of 75mm long complete all as specified & shown in drg.

(h) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coats of french polish to old and new surface of almirah mess utensil all as directed by Engineer-in-charge.

Repair to Table 900x900x760 steel (Drg No. FD-121(M)

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for Gas welding to broken joints of table steel all as specified and directed.

(c) Cutting of worn out portion of legs of table and S&F new 25x25mm square pipe of 1.6mm thick piece of 3” to 4” long including gas welding complete all as specified and directed.

(d) M&L for preparation of old painted surface and applying one coat of black synthetic enamel paint complete all as specified and directed.

Repair to Stool dressing CB (Drg No. FD-27)

(a) M&L for removing old unserviceable short rail and S&F, new short rail of stool dressing made out of first class hardwood (teak wood) of similar size & shape complete all as specified & shown in drawing.

(b) M&L for removing old unserviceable long rail and S&F, new long rail of stool dressing made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(c) M&L for removing old unserviceable legs and S&F, new leg of stool dressing made out of first class hardwood (teak wood) of similar size & shape complte all as specified & shown in drawings.

(d) S&F, Canning patti made out of first class hard wood (teak wood) duly holes for caning fixed with steel screws 35mm long complete all as directed.

(e) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of side board all as directed.

Repair to Table dining 8 pers (Drg No. FD- 239 & FD/E6/MAP-II/03

(a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg.

(b) M&L for removing of old unservicable long rails and S&F, new teak wood long rail duly finished/smoothened complete all as specified & shown in drg.

(c) M&L for removing of old unservicable top side rails and S&F, new teak wood top side rail duly finished/smoothened complete all as specified & shown in drg.

(d) M&L for removing of old unservicable top side short rails and S&F, new teak wood top side short rails duly finished/smoothened complete all as specified & shown in drg.

(e) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg.

(f) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table all as directed by Engineer-in-charge.

Repair to Chair dining with cushion (Drg No. FD/E6/MAP-II/04

(a) M&L for removing of old broken rear leg of chair dinning and S&F new rear leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg.

(b) M&L for removing of old broken front leg of chair dinning and S&F new front leg made out of first class hard wood (teak wood) of similar size & shape complete as specified & shown in drg.

(c) M&L for removing of old broken stifner of chair dinning and S&F new stifner made out of first class hard wood (teak wood) of similar size & shape complete as specified & shown in drg.

(d) M&L for removing of old broken front/side/rear rail of chair dinning and S&F new front/side/rear rail made out of first class hard wood (teak wood) of similar size & shape including drilling holes for caning all as specified & shown in drg.

(e) M&L for removing of old broken back rest of chair dinning and S&F new back rest made out of first class hard wood (teak wood) of similar size & shape all as specified & shown in drg

(f) M&L for removing of old unserviceable seat of chair dinning and S&F new seat made out of 75mm thick, 40 denisity, U-foam covered with superior quality of tepastry cloth including stiching/fixing all as specified and directed.

(g) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of chair dining all as directed by Engineer-in-charge

Repair to Chair revolwing & Computer Chair TP & FD/E6/MAP/01

(a) Removing of old unserviceable hand rest of chair revolving/chair computer and S & F new hand rest black integral skin as shown on drg

(b) Removing of old unserviceable back of chair revolving/chair computer and S & F new back with PVC lipping alround as shown on drg

(c) Removing of old unserviceable seat of chair revolving/chair computer and S & F new seat with PVC lipping alround as shown on drg

(d) Removing of old unserviceable pedestal assy of chair revolving/chair computer and S & F new pedestal assy as shown on drg

(e) Preparation of old painted surface of chair revolving and applying one coat of synthetic enamel paint by spray with black enameled colour all as directed.

Repair to Stool steel 2' hight (DRG No FD-81(M))

(a) Preparation of old painted surface and applying one coat of Olive Green synthetic enamel paint complete all as specified and directed.

(b) Removing of old unserviceable stool top and S&F, new top of stool of 1.6mm thick MS sheet (top size 305 x 305) complete all as specified and shown on drawing.

(c) Removing of old unserviceable legs of stool and S&F, new legs of stool of 1.6mm thick MS sheet complete all as specified and shown on drawing.

(d) Removing of old unserviceable broken top rail of stool and S&F, new top rail of stool of 1.6mm thick MS sheet complete all as specified and shown on drawing.

Repairs to Charpoy GI 25mm ply top (Drg No FD-220R)

(a) Removing unserviceable ply top and S&F new plywood top of size 1980mmx900mmx12mm thick BWR grade ISI Marked . Plywood top shall be fitted with appropriate sizes of nuts and bolts with washer all as specified and shown on drawings and as directed.

(b) Removing of damaged/broken long rail from charpoy GI pipe and S&F new long rail made out of GI Pipe 32mm bore (ISI marked) medium grade including threading both sides all as specified in Drg & directed.

(c) Removing of old damaged/broken short rail from Charpoy and making of short rail from old u/s long rail (retervied from ser item No 1.02 above) including threading & fixing in charpoy GI Pipe all as specified in Drg & directed.

(d) Removing of old damaged/broken leg from charpoy and making leg from old u/s short rail (retervied from ser item No 1.02 &1.03 above) including threading & fixing in charpoy GI Pipe all as specified in Drg & directed.

(e) Removing of old broken/damaged check nuts and S&F new check nuts of 32 mm dia heavy duty to Charpoy GI pipe all as specified in Drg & directed.

(f) Removing old broken/damaged GI elbow, 3 way, 32 mm bore and S&F new GI elbow, 3 way, 32mm bore (ISI marked) to Charpoy GI pipe all as specified in Drg & directed.

(g) Removing damage/broken welded suports from charpoy GI Pipe 32mm and S/F new support made out of 40 x 6 mm flat iron, 850 mm long duly welded to charpoy including applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified in Drawing and directed.

Navkar Enterprises