Construction of CID office Building at Bilaspur Distt Bilaspur HP including internal water supply and sanitary installation external sewerage system development of site and Co 5000 litres capacity Rain Water Harvesting Tank

Amount

Cutting in earth work in all heights/depths and in all kinds of soil such as kankar, moorum, shingal and decomposed or soft rock, hard rock i.e. their intermediate classification and chiselling/wedging out rock where blasting prohibited including saturated soils and filling in embankments etc. where necessary and disposal of all excavated unserviceable material in all leads and lifts including through mechanical transportation, the disposal of the unserviceable material will be done on approved dumping site. Any damage to private/public property during execution will be restored by the contractor whatsoever the nature of the same may be. The serviceable material will be stacked in specified dimensions in all leads and lifts as per the direction of the Engineer-in-charge.

Excavation in earth work in all kinds of soils such as pick work, jumper work, blasting work and chiselling/wedging out of hard or soft rock and disposal of all excavated earth up to any leads and lifts disposed earth to be levelled and neatly dressed as directed by the Engineer-in-charge.

Excavation in earth work and banking in 20 cm. layers including breaking clods, ramming and dressing ground for the purpose of making embankment or filling up ground depressions upto a lead of 20 metres and lift upto 1.50 metres.

Excavation in foundations, trenches etc. in all kinds of soils such as pick work, jumper work, and chiselling/wedging out of hard or soft rock up to all heights stacking the excavated soil not more than 3 meters clear from the edge of excavation and then returning the stacked soil in 15 cms. layers, when required into plinths, sides of foundations etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in-charge in all leads and lifts.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete including carriage of material in all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron frames 30x30x5mm so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies heights of propping and centering below supporting floor to ceiling in all heights and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of materials in all leads and lifts:-

Foundation, footings, bases of columns etc. and mass concrete.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like floors etc. up to 200 mm in thickness.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like.

Columns, pillars, posts and struts:- Square, rectangular or polygonal in plan.

Beams, cantilever, girders and lintels:- Sides and soffits of beam, beam haunchings, cantilevers, bressumers and lintels not exceeding 1 mtr in depth in all heights from floor.

Edges of slabs and breaks in floors and walls:- Under 20 cm. wide.

Providing and laying cement concrete 1:4:8(1cement:4sand:8graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material in all leads and lifts.

Providing and laying cement concrete 1:6:12(1cement:6sand:12 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of centering and shuttering in foundation and plinth including carriage of material in all leads and lifts.

Providing and laying cement concrete 1:2:4(1cement:2sand:4graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material in all leads and lifts.

Providing and laying cement concrete having strength of M-20 mixed design aggregate mechanically mixed and vibrated and curing complete including centring and shuttering etc but excluding cost of reinforcement. including carraige of material in all leads and lifts:- In Mouldings as in cornices and windows sills etc. not exceeding 15cm. in girth

Providing and laying mechanically mixed cement conctere having strength of M-20 mixed design aggregate mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of material in all leads and lifts:-

Foundations, footings, bases of columns and the like mass concrete.

(a) Walls (any thickness but not less than 0.10 metres thickness) including attached pillasters buttresses plinth and string courses etc.

Suspended floors, roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers in all heights.

Columns, pillars, posts and struts up to all heights.

Vertical and horizontal (thickness not more than 0.10 m) individually or forming box louvers and projected band uupto floor all level.

Providing and laying mechanically mixed vibrated reinforced cement concrete of mixed design to have characteristic strength of M-20 GRADE for reinforced concrete chajjas not exceeding 10 cm thickness upto all heights including finishing the exposed surface with cement mortar 1:3(1cement:3sand) to give a smooth and even surface, centering/form work and curing complete excluding cost of reinforcement including carriage of material in all leads and lifts.

Providing tor steel reinforcement for RCC work including bending, binding and placing in position complete including cost of binding wire up to all heights including carriage of material in all leads and lifts.

Applying cement slurry on R.C.C. slab or cement concrete work using 2.75 kg of cement per sq. metre of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surface complete including carriage of material in all leds and lifts.

Providing and laying cement concrete 1 : 8 : 16 (1 cement : 8 sand : 16 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of centering and shuttering in screed laid on slab including carriage of material in all leads and lifts.

Providing and laying cement concrete 1:5:10 with 15% plums and curing complete including the cost of form work for plain/reinforced concrete in retaining walls, breast walls, the size of plum should be 150 to 300mm as per drawing and HP. PWD technical specifications including carriage of material in all leads and lifts.

Providing throating or plaster drip and moulding to R.C.C. chajjas including carriage of material in all leads and lifts.

Brick work using 2nd class common burnt clay building bricks in foundation and plinth in cement mortar 1:6 (1 cement : 6 sand) including carriage of material in all leads and lifts.

Brick work using 2nd class common burnt clay building bricks in superstructure above plinth level up to all floor level, in cement mortar 1:6(1cement:6sand), including carriage of material in all leads and lifts.

Half brick masonry using 2nd class common burnt clay building bricks in superstructure above plinth level upto floor all level in cement mortar 1:4(1cement:4sand) including carriage of material in all leads and lifts.

Random rubble masonry/polygonal rubble masonry (un-coursed/brought to course) with hard stone of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12(1cement:6sand:12 graded stone aggregate 20 mm nominal size) at plinth in cement mortar 1:6 (1cement:6sand) including carriage of material in all leads and lifts.

Stone filling behind retaining walls including carriage of material in all leads and lifts.

Providing weepholes in brick masonry/stone masonry/plain reincorced concrete abutment, wing wall, return wall with 100mm dia PVC pipe extending through the full with of the structures with slop of 1(v):20(H) towards drawings facae complete as per drawing and technical specification clauses 614, 709, 1204.3.7 including carriage of material in all leads and lifts.

Providing wood work in frames of doors, windows, clerestorey windows and other frames wrought framed and fixed in position ivory coast teak wood including carriage of material in all leads and lifts.

Providing and fixing Ivory Coast teak wood 40mm thick panelled door shutters having styles and top rail 100mm width and bottom rail 200mm width lock rail 150mm width with panel insert of 12mm thick commercial veneered flat pressed ply wood Board of BWP grade confirming to IS. 303-1975 and bounded with BWP type synthetic resin confirming to I.S. 848-1974 including providing and fixing 2nd class Indian teak wood beading of size 38x20mm along the panels on both faces of shutters and providing wooden cleats and ISI marked black enamelled M. S. butt hinges with necessary screws all complete as per drawing and specification and instruction of Engineer-in-Charge including carriage of material in all leads and lifts.

Providing and fixing Ivory Coast teak wood 40mm thick single/double leaf glazed window shutters having styles and top rail and bottom rail 75mm width and chamferred edged 2nd class Indian teak wood moulding 20x12mm for glass panes complete including the cost of glass panes and bright finished black enamelled iron butt hinges with necessary screws including carriage of material in all leads and lifts.

Providing and fixing Ivory Coast teak wood 40mm thick wire gauge shutters using M.S. wire gauge of IS gauge designation 85 G with wire of dia 0.56 mm for doors, windows and clerestorey window and providing and fixing 2nd class Indian teak wood chamferred edged beading of 20x12mm including bright finished black enamelled iron butt hinges with necessary screws complete as per drawing and specification and instruction of Engineer-in-Charge including carriage of material in all leads and lifts.

Supplyig and fixing glass panes with putty and nails :- Plain glass 4mm thick including carriage of mateial in all leads and lifts.

Providing and fixing plain square edged cover fillets (beading) 40mmx12mm section with wood screws in ceiling at junction 1st class Indian teak wood including carriage of material in all leads and lifts.

Providing and fixing square edges cover fillets (beading) 19mmx6mm section including mitring at junctions with wood screws and nails complete including carriage of material in nall leads and lifts:- 1st class Indian teak wood.

Providing and fixing MS grills of required pattern in wooden frames of windows etc. with MS flats square or round bars with round headed bolts and nuts welded or by screws including carriage of material in all leads and lifts.

Providing 40x3mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm in cement concrete 1:3:6(1cement:3sand:6graded stone 20mm nominal size)including carriage of material in all leads and lifts.

Fixing anodized power coated aluminium sliding door bolts including carriage of material in all leads and lifts:-

Fixing anodized power coated aluminium tower bolts including carriage of material in all leads and lifts:-

Fixing anodized power coated aluminium handles including carriage of material in all leads and lifts:-

Fixing bright finished hard drawn hooks and eyes:- 150mm including carriage of material in all leads and lifts.

Fixing oxidized M.S. hasps and staples 115mm (safety type) including carriage of material in all leads and lifts.

Fixng 100mm bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete including carriage of material in all leads and lifts.

Fixing bright finished or/and black enamelled iron ( Helical door spring 150mm ) including carriage of material in all leads and lifts.

Providing and fixing 4mm thick water proof kit ply of standard quality ISI mark and approved shade and colour in wall linning including mitring at junctions, butt jointing and nails complete (Frame work for base to be measured and paid for separately) including carriage of material in all leads and lifts.

Providing and fixing 19mm thick commercial Board water proof shutters for cup boards including fixing with nickel plated piano hinges with screws etc. complete including carriage of material in all leads and lifts.

Providing and fixing 19mm thick water proof commercial board in shelves/box for cup board with butt joints and fixing with nails and screws etc. complete including carriage of material in all leads and lifts.

Providing and fixing chromium plated brass 50mm cup board or wardrobe knobs with nuts compiete including carriage of material in all leads and lifts.

Providing and fixing 65x35mm special quality chromium plated brass cup board lock with six levers including necessary screws etc. coplete (Indian made) including carriage of material in all leads and lifts.

Providing and fixing glass strips in joints of terrazzo floors 40mm wide and 4mm thick including carriage of material in all leads and lifts.

Cement concrete flooring 1:2:4(1cement:2sand:4graded stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement including carriage of material in all leads and lifts:- 50mm thick.

Providing and laying granite stone in flooring 20mm (average) thicknss base of cement mortar 1:3 (1cement:3sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete 20mm thick including carriage of material in all leads and lifts.

Extra over item No. 47 for granite stone moulding, nosing etc. including carriage of material in all leads and lifts.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles nitco or equivalent (any size and colour ) manufactured of approved shade and colour in flooring, treads of steps and landing laid over 12mm thick cement mortar 1:3 (1cement:3sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including cost of tiles where required to be cut and carriage of material in all leads and lifts.

Providing and laying Duro stone vetrified tiles (any size) 10mm thick in grey/coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1cement:3sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of material in all leads and lifts.

Providing and laying Duro stone vetrified tiles (any size) 8mm thick in grey/coloured or of approved shade in skirting riser of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1cement:3sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of material in all leads and lifts.

Providing and laying heavy duty precast cement concrete inter locking paver blocks vibro compacted upt M-50 grade including border or kurb block grey or coloured over slub-base of concrete with 25mm thick average thickness of cement lmortar 1:4 (1cement:4sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curring, rubbing and polishing complete (Sub base concrete floor to be paid for separately) including carriage of material in all leads and lifts:- 80mm thick inter locking blocks.

Providing and fixing 15 cm. wide 45 cm. overall semicircular plain G.I. sheetgutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per 0.63mm thick sheet including carriage of material in all leads and lifts.

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm diameter with prepainted limpet and rubber washer complete with all accessories as required as per the direction of Engineer-in-charge including carriage of material in all lead and lifts.

Providing and fixing ridges or hips 60cm over all with 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm diameter with prepainted limpet and rubber washer complete with all accessories as required as per the direction of Engineer-in-charge including carriage of material in all lead and lifts.

Providing and fixing valley 60cm over all with 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm diameter with prepainted limpet and rubber washer complete with all accessories as required as per the direction of Engineer-in-charge including carriage of material in all lead and lifts.

Proiding and fixing on wall face P.V.C. (D-plast) rain water pipes of working pressure not less than 4.5kg per sqm. including filling the joints with approved adhesive complete including carriate of material in all leads and lifts:- 150mm dia.

Providing and fixing on wall face P.V.C. (D-plast) accessories for rain water pipes including filling the joints with approved adhesive complete including carriage of material in all leads and lifts:-

(a) P.V.C. Plain bend 150mm dia.

(b) P.V.C. plain shoe 150mm dia.

Providing and fixing MS holder bat clamps of approved design to CI or SCI/P.V.C pipes embedded in and including cement concrete blocks 10x10x10cms of 1:2:4mix(1cement:2sand:4graded stone aggregate 20mm nominal size) and cost of cutting holes and making good the walls etc. including carriage of material in all leads and lifts. 150mm diameter.

Providing and fixing M.S. B.P. Sheet 1.6mm to 2mm thick in eaves board/facia/ soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured and paid for separately) including carriage of material in all leads and lifts.

Steel work welded in built up sections trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of red lead paint including carriage of material inn all leads and lifts:-

(a) In beams, joists, channels, angles, tee, flats with connecting plates or angle cleats as in main and cross beams, hip and jack rafters, purlins connected to common rafters and the like.

(b) In gratings, framed guard, bars, ladders, railings, brackets and similar work.

Providing and fixing M.S. round holding down or anchor bolts with nuts and washer plates complete including carriage of material in all leads and lifts.

Supplying and fixing rolling shutters of approved make made of 80mmx1.25mm M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft, with brackets side guides and arrangement for inside and outside locking with push pull operation complete but excluding the cost of the top cover and spring:- Shutters having width below 3.5 metres including carriage of material in all leads and lifts.

Providing and fixing 27.5centimetre long wire spring grade No.2 for rolling shutters including carriage of material in all lads and lifts.

Providing and fixing ball bearing for rolling shutters including carraige of material in all leads and lifts.

Providing and fixing top cover for rolling shutters shutters having width below 3.5 metre including carriage of material in all leads and lifts.

Applying priming coat over new steel and other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete :- With ready mixed priming paint brushing red lead, Red-oxide/zinc oxide chrome including carriage of material in all leads and lifts.

Painting coats (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give fair and smooth surface including cleaning the surface of all dirt, dust and other foreign matter. Enamel paint other than white/white enamel paint including carriage of material in all leads and lifts.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil grease, dirt and other foreign matter sand papering and knotting including carriage of material in all leads and lifts:- Readymixed paint brushing wood primer pink.

Painting coats (excluduing priming coat) on new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of dirt, dust and other foreign matter sand papering and stoping including carriage of material in all leads and lifts:- Enamel paint other than white/whiteEnamel paint paint.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other forein matters sand papered smooth to give final matter finish to the surfacae complete including carriage of material in all leads and lifts.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima)or its equalized on undecorated wall surfaces (two coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matters etc. including and paper smooth complete. including carriage of material in all leads & lifts.

Distempering coats with oil bound distemper of approved brand and manufacture and of required shade on undecorated wall surface to give an even shade after thoroughly brushing the surface clean of all grease, dirt, loose pieces of scales including preparing the surface even and sand papered smooth including carriage of material in all leads and lifts.

Distempering coats with oil bound distemper of approved brand and manufacture and of required shade on undecorated ceiling and/or slopped roofs to give an even shade after thoroughly brushing the surface clean of all grease, dirt, loose pieces of scales including preparing the surface even and sand papered smooth including carriage of material in all leads and lifts.

6mm cement plaster to ceiling in cement mortar including carriage of material in all leads and lifts. In cement mortar 1:3(1cement:3sand).

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering up to all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth including carriage of material in all leads and lifts:-

In cement mortar 1:3 (1 cement : 3 Sand)

In cement mortar 1:6 (1 cement : 6 Sand)

Extra over item No. 76.01 for finishing with floating coat of neat cement slurry including carriage of material in all leads and lifts.

20mm cement plaster in single coat on rough side of brick/stone masonry for interior plastering up to all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth including carriage of material in all leads and lifts:- In cement mortar 1:6 (1cement:6sand).

Providing plinth protection 50mm thick in cement concrete 1:3:6(1 cement : 3 sand :6graded stone aggregate 20mm nominal size) including finishing the top surface of concrete smooth including carriage of material in all leads and lifts.

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed of dry bricks/stone aggregate 40mm nominal size) well rammed and consolidated and grouted with fine sand including preparation of ground including carriage of material in all leads and lifts.

Constructing course rubble hammer dressed “U” shape open surface drain with side wall 15x22cm in cement mortar 1:6(1cement:6sand) and inside plastering with cement mortar 1:3(1cement:3sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1cement:5sand:10graded stone aggregate 40mm nominal size) and 7.5cm cement concrete 1:2:4(1cement:2sand:4graded stone aggregate of 20mm nominal size) and finished with a floating coat of neat cement complete as per standard design including carriage of material in all leads and lifts.

Providing and fixing 40 mm nominal bore galvanized M. S. tube (light grade) Out let in cement mortar 1:3 (1cement:3sand) including carriage of material in all leads and lifts.

Providing chases 75mm wide and 50mm deep (average size) in walls for G. I./C. I. pipes and filling the same with cement concrete 1:3:6 (1cement:3sand:6graded stone aggregate 20mm down gauge after the G. I./C. I. pipe is laid (excluding the cost of G. I./C. I. pipe) including carriage of material in all leads and lifts.

Providing and fixing to wall ceiling and floors polythlene Aluminium-polythylene (PE-AL-PE) composite pressure pipes confirming to IS- 15450-2004, U.V. stablized with carbon black having thermal stability for hot and cold water supply, capable to withstand temperature material (Engineering plastic blend and brass inserts wherever required) e. g. elbows, tees, reducers, couplours and connectors etc. with clamps at 1.00 metre spacing. This includes testing of joints complete as per the directions of Engineer-in-Charge inclding carriage of material in all leads and lifts:-

(a) 16mm outer dia.

(b) 20 mm outer dia.

Making connection of galvanized steel distribution branch with galvanized mild steel main 20 to 40mm nominal bore by providing and fixing tee including cutting and threading the pipes complete including carriage of material in all leads and lifts.

Providing and fixing sand cast/cast iron spun and spigot and socket soil waste and ventilating pipe (lead caulked joints to be measured paid for separately) including carriage of material in all leads and lifts:- 100mm nominal size.

Providing and fixing cast iron cowl including carriage of material in all leads and lifts:- 100mm nominal size.

Providing and fixing PVC water storage tank of ISI : 12701 marked, G. I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level including carriage of material in all leads and lifts:-

i) 1000 litres net capacity.

ii) 500 litres net capacity.

Providing and fixing G.I./M.I. unions of following sizes(where not included in the item) including carriage of material in all leads and lifts confirming to BIS specification:-

(a) 15mm nominal size

(b) 20mm nominal size.

Providing and fixing brass full way valve with wheel including carraige of material in all leads and lifts.

(i) 15mm nominal size

(ii) 20mm nominal size

Providing and fixing high pressure PVC spigot and socket soil waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts:-

(a) 75mm nominal bore.

(b) 110mm nominal bore.

Providing and fixting PVC clamp ISI marked of approved design with steel screws and rawl plugs etc. complete including carriage of material in all leads and lifts:-

(i) 110mm dia.

(ii) 75mm dia.

Providing and fixting PVC door bend with oval access door, ISI marked insertion rubber washers 3mm thick bolts and nuts including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts:-

(i) 110mm dia.

(ii) 75mm dia.

Providing and fixting PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts:-

(i) 110mm dia.

(ii) 75mm dia.

Providing and fixting single equal branch with oval access door, ISI marked insertion rubber washers 3mm thick bolts and nuts including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts:-

(i) 110mm dia.

(ii) 75mm dia.

Providing and fixting PVC collars ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts:-

(i) 110mm dia.

(ii) 75mm dia.

Providing and fixting PVC cowl ISI marked of approved design with steel screws and rawl plugs etc. complete including carriage of material in all leads and lifts:-

(i) 110mm dia.

(ii) 75mm dia.

Providing and fixing PVC floor trap ISI marked of self cleaning including fixing with approved adhesive, cost of cutting andn making god the wall and floors etc. complete including carriage of material in all leads and lifts:- 110mm x 75 mm.

Providing and fixing vitreous china wash down, water closet (European type S.C. pan) with integral "P" or "S" trap including jointing the trap with soil lpipe in cement mortar 1:1 (1cement:1sand)) (Seat and cover to be measured and paid for separately) including carriage of material in all leads and lifts:- Anglo Indian Universal closet.

providing and fixing 100mm size 'P' or 'S' trap for water closet (squatting pan) including jointing the trap with tha pan and soil pipe in cement mortor 1:1 (1 cement :1 sand)

Providing and fixing plastic seat (Solid/Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers including carriage of material in all leads and lifts:- Solid type white plastic seat and cover.

Providing and fixing PTMT Coloured / white high density polyethylene / poly propylene 10.00 litres capacity (full flush) European standred control low level PVC flushing cistern with fittings with a pair of brackets with fitting such as lead valve, syphon,15mm nominal size PVC ball valve with polythene float, with push button,coulping for connection with inlet and outlet and overflow pipes40 mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet ( overflow pipe to be measured and paid for separately) including carriage of material in all leads and lifts,

Providing and fixing vitreous china wash basin with single hole for pillar tap with C.I.or M.S.brackets painted white including cutting holes and making good the same but excluding fittings including carriage of materials :- Flat back 550mmx400mm.

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M. S. Brackets painted wihite including cutting holes and making good lthe same but excluding fitting including carriage of material in all leads and lifts:- 610 x 510 mm with owl depth 200mm.

Providing and fixing C.P. Brass waste for wash basin or sink including carriage of material in all leads and lifts:- 32mm dia.

Providing and fixing M.I. union for wash basin or sink 32mm dia confirming to BIS specification including carriage of material in all leads and lifs.

Providing and fixing 32 mm P.V.C waste pipe for wash basin or sink including barss check nut including carriage of material in all leads and lifs.

Providing and fixing 100 mm dia chromium plated grating of superior quality for floor, gully or nahani trap including carriage of material in all leads and lifts.

Providing and fixing 600mmx450mm bevelled edge mirror of superior glass mounted on 6mm thick A. C. sheet plywood sheet and fixed to wooden plugs with C. P. brass screws washers including carriage of material in all leads and lifts.

Providing and fixing C. P. Brass Towel rail complete with C. P. Brackets fixed to wooden plugs with C. P. Brass screws including carriage of material in all leads and lifts:- 600mmx20mm.

Providing and fixing 600mmx120mm glass shelf with C. P. Brass bracket and guard rail complete, fixed to wooden plugs with C. P. Brass screws including carriage of material in all leads and lifts.

Providing and fixing toilet paper holder including carriage of material in all leads and lifts.C.P. brass.

Proiding and fixing C. P. Bottle Trap for wah basin and sink including carriage of material in all leads and lifts:- 30mm dia.

Providing and fixing C.P. brass bib tap with capastan head including carriage of material in all leads and lifts confirming to BIS specification:- 15mm dia.

Providing and fixing C.P. brass pillar tap with capastan head including carriage of material in all leads and lifts confirming to BIS specification:- 15mm dia.

Providing and fixing C.P. brass angle valve 15mm dia confirming to BIS specification including carriage of material in all leds and lifts.

Providing and fixing P.V.C. connection with brass unions including carriage of material in all leads and lifts:- 300/450mm length: 15mm nominal bore.

Providing land fixing C. P. Brass shower rose with 15mm or 20mm inlet including carriage of material in all leads and lifts:- 100mm dia.

Providing and fixing C.P. Brass concealed stop cock 15mm dia (confirming to BIS specification) including carriage of material in all leads and lifts.

Cutting holes through existing brick/stone walls including making good the same in cement mortar 1:6(1cement:6sand) per cm depth of cutting: Holes up to and including 400 mm square centimeter in area including carriage of material in all leads and lifts.

Providing and laying (to level or slopes) and jointing reinforced concrete(light duty) non-pressure pipes I.S. class NP-2 or P of the following internal diameter with collar and butt ends prepared for collar joints including testing of joints 150mm dia including carriage of material in all leads and lifts.

Providing and fixing stoneware gully trap grade ‘A’ complete with C.I. grating, brick masonry chamber in cement mortar 1:5(1cement:5sand) and water tight C.I. cover with frame of 300mmx300mm size (inside) the weight of cover to be not less than 4.53kg and frame to be not less than 2.72kg) square mouth trap 100mmx100mm size 'P' type including carriage of material in all leads and lifts confirming to BIS specification.

Constructing manhole with RCC top slab in 1:2:4mix(1cement:2sand :4graded stone aggregate 20mm nominal size) foundation concrete 1:4:8(1cement:4sand:8graded stone aggregate40mm nominal size) inside plastering 15mm thick with cement mortar 1:3(1cement:3sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4mix (1cement:2sand:4graded stone aggregate 20mm nominal size)finished smooth complete including curing and testing including carriage of material in all leads and lifts:-

(i) Inside size 800mmx800mmx 500mm deep including C.I. cover with frame (light duty single seal pattern-I) 455mmx610mm internal diamension total weight of cover and frame to be not less than 38 kg.(weight of cover 23 kg and weight of frame- -15kg) with 200 mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3(1cement:3sand).

(ii) Inside size 800mmx800mmx 1000mm deep including C.I. cover with frame (light duty single seal pattern-I) 455mmx610mm internal diamension total weight of cover and frame to be not less than 38 kg.(weight of cover 23 kg and weight of frame- -15kg) with 200 mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3(1cement:3sand).

Making connection of drain or sewer line with existing manhole including breaking in to and making good the wall, floorswith cement concrete 1:2:4 (1cement:2sand:4graded stone aggregate 20mm nominal size) cement plastered on both side with cement mortar 1 :3(1cement:3sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4mix (1cement:2sand:4graded stone aggregate 20mm nominal size)finished smooth complete including curing and testing including carriage of material in all leads and lifts:- for pipe 100mm to 150mm internal diameter / nominal size.

Providing 200mm wide cast iron rungs with chequered ribbed non slip surface including fixing inn manholes with 200mmx200mmx100mm in cement concrete 1:3:6 (1cement:3sand:6sand) in 20mm nominal size including carriage of material in all leads and lifts.

Supplying and fixing cast iron cover with out frame for manholes of for frame of 500mm internal diameter C. I. cover (medium duty) the weight of cover to be not less than 58 kg. including carriage of material in all leads and lifts.

Surinder Kumar